Panasonic CF-45 Series Reference Manual

LED Indicators ................................................... 3 Suspend/Hibernation Functions ...................... 4 Security Measures ............................................ 7 Computing On the Road ................................ 11 Battery Power ................................................. 13 Using PC Cards .............................................. 15 Adding Memory .............................................. 17 Port Replicator................................................ 18 Using a Printer................................................ 19 Using an External Display ............................. 20 Using USB Devices .................................................21 Infrared Data Communications ..........................22 Hard Disk Drive............................................... 23 Setup Utility .................................................... 24 Technical Information .................................... 29 Computer Diagnosis ...................................... 32 DMI Viewer ...................................................... 33 Dealing With Problems................................... 34 Contents We recommend that this Reference Manual be printed out. 95 NOTE: NOTE provides a useful fact or helpful information. CAUTION: CAUTION indicates a condition that may result in minor or moderate injury. WARNING: WARNING indicates a hazard that may result in moderate or serious injury. [Start]-[Shut Down]: This illustration means to click [Start], then to click [Shut Down]. (For some applications, you may need to double-click.) Enter : This illustration means to press the [Enter] key. Fn + F5 : This illustration means to press [Fn], and while holding down on [Fn], to press [F5]. : This illustration means to refer to the Operating Instructions

(When the brightness is at its maximum value, is displayed.) By pressing this key combination, you can select either an external display, LCD or simultaneous. Pressing this key combination turns off audio from the internal speaker and headphone jack. Pressing it again turns audio back on. Pressing this key combination adjusts the volume of the internal speaker and headphone jack. This key combination cannot be used to adjust the volume of the beep sound. Pressing this key combination causes the current screen on the display to be saved to memory, and powers off the computer. When the computer is pow- ered on again, this same screen will be displayed. (The computer must be plugged into the AC adapter or have a battery pack with sufficient remaining power installed.) Pressing this key combination temporarily disables the power management feature of the Setup Utility. ( page26) Pressing it again, or powering the computer off and then back on enables the power management feature of the Setup Utility. Pressing this key combination displays the remaining battery capacity on the screen. Pressing this key combination cuts off power to the LCD display until opera- tion is resumed by pressing any key. Key Combinations CAUTION Do not press the following key combinations repeatedly in (quick) succession. Do not press the following key combinations while using the trackball (mouse) or other keys. LCD brightness control Display change Speaker on/off switch Volume control ( down) Volume control ( up) Power off using the sus- pend function Power Management enable/disable switch Remaining capacity of the battery pack Standby mode for conserving power NOTE Fn + F2 Fn + F3 Fn + F4 Fn + F5 Fn + F6 Fn + F7 Fn + F8 Fn + F9 Fn + F10

input is capitalized. These indicators light green when NumLk is pressed and then KeyPad is pressed while holding down the Fn key. This causes a portion of the keyboard to func- tion as a numeric keypad. Depending on the application, the [Enter] key may function differently than normal. This indicator lights green when ScrLk is pressed. Scroll lock functions differ- ently depending on the application. This indicator lights green when KeyPad is pressed while holding down Fn. When the indicator is not lit, a portion of the keyboard functions as arrow keys. Depending on the application, the [Enter] key may function differently than normal. This indicator lights when the CD-ROM drive is accessed. This indicator lights when the floppy disk drive is accessed. This indicator lights when the hard disk drive is accessed. Not lit : AC adapter not connected or charging not being performed. Lit constantly orange : Charging in progress. Lit constantly green : Charging finished. Lit constantly red : Battery is low (remaining battery capacity is approx. 9% or less). Flashing red : Battery pack or charging malfunction. Flashing orange for 5 seconds after the AC adapter is connected : Charging on standby. (The ambient temperature is outside the allowable range.) Not lit : Power off Lit constantly green : Power on Flashing green : Suspend mode Caps Lock NumLk (Numeric key) ScrLk (Scroll lock) KeyPad (Arrow key) CD-ROM status Floppy disk status Hard disk status Battery pack status Power status LED Indicators

page 24) (Do not touch the power switch while your computer is entering the hibernation mode.) Suspend Mode or Hibernation Mode 2 Using and , select [Power Management], then press Enter 3 Close the Setup Utility ( page 24) 4 Setting the Suspend or Hibernation Function If you want to immediately start up and continue an application after shutting down your com- puter, you can do so by using the suspend or hibernation function. Starting Up Your Computer Quickly Power off your computer Function Suspend function Hibernation function Where data is saved to Memory Hard disk Speed Fast Somewhat slow Requires power supply Yes (if power is cut, all data is lost) Power not required to maintain data Shutting Down Using the Suspend or Hibernation Function Suspend/Hibernation Functions Differences between the suspend function and hibernation function The computer should be set for suspend or hibernation ( see the above procedure). If the power switch is held for over four seconds at the ON position, the power goes OFF without activation of the suspend or hibernation function. Do not slide the power switch and hold it for more than four seconds. If the computer will not be operated for an extended period of time, it is recom- mended that hibernation mode is used instead of suspend mode. Using and , select [Power Switch], set [Suspend] or [Hibernation] with , then press Esc

) is displayed upon sliding the power switch, your password has been set. CAUTION After the display returns, the computer needs a short period of time to reinitialize. This takes about 15 seconds. Do not shut down or restart Windows during this time, as this may subsequently cause Windows to operate abnormally. Do not install or remove peripherals while your computer is in the suspend or hiber- nation mode; abnormal operation may result. When operation resumes, serial devices such as a mouse or modem, or your PC Cards may not work. In such cases, you will need to restart your computer or reinitialize the individual devices. Do not use the suspend or hibernation functions when using USB devices. Set [USB Controller] of [Supervisor Setup] to [Disable] in the Setup Utility when using the suspend or hibernation functions. Shutting Down Using the Suspend Function Fn + F7 or select [Suspend] from the [Start] menu Suspend Mode [Suspend] is deleted from the [Start] menu by unchecking [Allow Windows to manage power use on this computer.] in [Start] - [Settings] - [Control Panel] - [Power] or by unchecking [Show suspend command on Start menu] in [Advanced]. NOTE When you select [Suspend] from the [Start] menu: Turn your computer on

When restarting from or shutting down to the suspend or hibernation mode, do not touch the trackball or move the mouse (serial or PS/2 type) if one is connected. There are cases where these devices will fail to operate; you will have to restart your computer using the keyboard. Do not power off during the following periods (you may corrupt your data or file): • While the FDD indicator ( ), HDD indicator ( ) or CD-ROM indicator ( ) is on. • While playing/recording audio files. • While communications software is being used. Do not use the suspend or hibernation function when using an operating system other than the one that comes with your computer, the diagnostics program (DIAG45), the Setup Utility, or when experiencing static electricity or noise. If you hold down on the Alt , Ctrl or Shift key to enter the suspend or hibernation mode, after resuming operation, you must press the same key. For example, if you hold down on the Shift key while sliding the power switch, upon resuming, if you do not press the Shift key again, only capital letters will result from typing. If your computer locks up, press the reset button. All data not saved is lost when this button is pressed. In the suspend mode, power is consumed. If PC cards (e.g., a modem card) are inserted, more of that power is consumed. When all power has been consumed, all data at shut- down is lost since it is retained in memory. We therefore recommend plugging in the AC adapter when using the suspend function. Do not use the suspend or hibernation function during the following periods. The sus- pend or hibernation function, or peripherals may not work. When a file in external devices such as a CD-ROM drive, external hard disk, or ATA card is opened, the suspend or hibernation function may not work. In such cases, close the file. SCSI cards may not recover after entering the suspend or hibernation mode. If this occurs, restart the computer. Precautions for Using the Suspend or Hibernation Function Suspend/Hibernation Functions

Same as above, but while you’re away temporarily You want to prevent theft or damage to data by using a floppy disk You do not want your Supervisor Setup changed without permission You want to prevent theft of your computer To prevent unauthorized access of your computer, the various security measures are provided below. 1 2 Setting the user password (enabling, changing, disabling) 4 3 To disable your password Using the and keys, select [Delete User Password], then press Enter . Go to step 7. CAUTION Your password will not be displayed on the screen. Please limit your password to seven characters. Note that there is no distinc- tion between upper and lower case letters. White colored keys can be used. Note that the space bar and function keys cannot be used. Do not input your password while holding down on Shift or Ctrl . Use only the upper horizontal row of numeric keys to input your user pass- word. Do not forget your password. If a password is forgotten, you will be unable to use your computer. Run the Setup Utility ( page 24) Using and , select [System Setup], then press Enter Using and , select [User Password], then press Enter To enable or change your password Enter your password at the [Enter User Password], then press . Set the User Password. Without the password, access to your computer is impossible. When the User Password is set When you do not want your computer to be used without permission * If you are starting from the suspend mode, if after three attempts the correct password is not input, or if no password is entered for about a minute, the computer returns to the suspend mode. Over three incorrect attempts, If the correct password is input, Will Start Will Not Start* (Power off) Upon entering your User Password and pressing Enter . 5 Re-enter your password at the [Enter User Password Again] (This is for confirmation purposes.) Using and , select [Set User Password], then press Enter 6 Situation Function to use Reference User Password below Coffee break Password page 8 Prevent operation by using a floppy disk page 9 Supervisor Password page 9 Use a security lock

page 24) 7 You should set the “Coffee break Password” (Note that you must first set the User Password). When you input your selected key combination, the computer locks (key input, use of the trackball and use of an external mouse are no longer possible). Alt + Ctrl + F9 Setting the Coffee break Password (enabling or disabling) Do not leave your computer just after sensitive data had been shown on the screen. It is impossible to lock your computer from an external device, such as a mouse connected through the serial port or the USB device is used. During the coffee break, is displayed on the screen. If the operations de- scribed below are performed during the coffee break, the indication may disappear. In order to quit the coffee break and again begin using the computer, input your password. If a different popup window is displayed by using key combination. If the computer is returned from the standby mode. If the serial mouse is moved. CAUTION (Example of a selected key combination) The computer is locked When leaving your desk When an incorrect password is inputted, Operation resumes Operation does not resume When you do not want your computer to be used without permission while away temporarily At the confirmation screen, press Enter Input the correct password used at startup and press Enter . 8 Press Esc to end the password setting procedure CAUTION To prevent the changing of your password without permission • When running the Setup Utility, do not leave your computer even for a short time. • Set the User Password Protection option ( page10). When the coffee break password is set 1 Set the User Password ( page 7 to 8, step 1 to 7 ) 2 To disable the Coffee break Password Using and , select [Coffee break Password], then set [Disable] with . Go to step 4. Close the Setup Utility ( page 24) 4 Press Esc to end the password setting procedure 3 5 Using and keys, select [Key Combination for Coffee break], then set your combination of keys with To enable the Coffee break Password Using and , select [Coffee break Password], then set [Enable] with .

ten accidentally by using a floppy disk. You can also set your computer to be unbootable from a floppy disk. Preventing the use of a floppy disk Even when one tries to access a floppy disk, Procedure 1 Run the Setup Utility ( page 24) This error message is displayed. Using and , select [Supervisor Setup], then press Enter 2 Using and , select [Boot Up Drive], then set either [HDD FDD] or [CDD FDD HDD] with 3 CAUTION When changing to the [HDD FDD] or [CDD FDD HDD] setting, to continue read/write operations from a floppy disk and to use the hard disk drive or CD-ROM to start, press Esc and go to step 5. 4 Using the and , select [Floppy Operation], set [Disable] with , then press Esc 5 When you do not want your Supervisor Setup changed without permission Set the Supervisor Password. After it has been set, no changes can be made to the Supervisor settings unless the password is entered. When the supervisor password is set In the Setup Utility ( page 24), if is displayed, NOTE Supervisor Setup May be Opened Supervisor Setup Can not be Opened When the supervisor password is incorrect or when the user password is entered, (Or, even when the correct supervisor password is entered). page 36 Input the correct supervisor password and press Enter , You may wish to protect the User Password ( page 10). (There are cases in which the Supervisor Setup does not appear on the main screen). page 24 Close the Setup Utility ( page 24) When you want to prevent theft of or damage to data by using a floppy disk Security Measures

(enabling, changing, disabling) 1 2 Run the Setup Utility ( page 24) Using and , select [Supervisor Setup], then press Enter 3 Using and , select [Supervisor Password], then press Enter 4 To enable or change your supervisor password Enter your password at the [Enter Supervisor Password], then press . CAUTION Your password will not be displayed on the screen. Please limit your password to seven characters. Note that there is no dis- tinction between upper and lower case letters. White colored keys can be used. Note that the space bar and function keys cannot be used. Do not input your password while holding down on Shift or Ctrl . Use only the upper horizontal row of numeric keys to input your user pass- word. Do not forget your password. If a password is forgotten you will be unable to use your computer. 5 Re-enter your password at the [Enter Supervisor Password Again] (This is for confirmation purposes.) NOTE Using and , select [Set Supervisor Password], then press Enter 6 At the confirmation screen, press Enter 7 8 Press Esc to end the password setting procedure 9 Close the Setup Utility ( page 24) When you do not want the User Password enabled, changed, or disabled with- out permission, use and to select [User Password Protection], then set [Enable] with . Using and , select [Delete Supervisor Password], then press Enter . Go to step 7. To disable your supervisor password Security Measures

away from your home or office. In the following, information is provided on how to maximize use of the battery pack which is necessary for such computing. POINT 1 Four Important Points POINT 2 Conserving Power Before stepping away from your computer, press Fn + F10 to put your computer in the standby mode The standby mode helps you conserve power by cutting off power to the LCD. To resume, you may press any key other than Fn or move the trackball. Things to Remember Be sure to charge your battery before and after use. To get the maximum use of your battery, set the power man- agement mode. POINT 3 Check to see that you have your AC adapter with you before leaving your home or office. Purchasing an extra battery (CF-VZS251AW*) and the optional battery charger (CF-VCB251W or CF-VCB251AW) is highly recommended. * Do not use CF-VZS251W with this Computer. Always watch your battery level! POINT 4 In the power management mode, the setting of [Advanced] is recommended ( page 12) With the Setup Utility, you can set the [Advanced] mode. This mode allows you to maximize power save regardless of whether you are using only the battery pack or the AC adapter. Leave your computer off when it is not in use ( ) Setting the suspend/hibernation timeout ( page 12) The suspend or hibernation function ( page 4) allows you to save power by automati- cally cutting off power when the computer is idle or there is no access to individual de- vices for 4 or 16 minutes. If [Advanced] or [Standard (Battery/AC adapter)] is selected for [Power Saving], the suspend / hibernation timeout function will go into effect for both the battery pack and the AC adapter. If, however, [Standard (Battery)] is selected for [Power Saving], it will go into effect only during operation by the battery. The standby timeout function is automatically set when [Advanced] or [Standard] is set. Note that the standby timeout precedes the suspend/hibernation timeout. It should be noted that for some applications, the suspend/hibernation timeout will not work properly. NOTE If you plan to use only the battery pack or set the power management, it is necessary to check [Allow Windows to manage power use on this computer] in [Start] - [Settings] - [Control Panel] - [Power]. If no check is added, the hibernation timeout will not occur. Computing On the Road By repeatedly pressing the keys to maximize the brightness ( will be displayed), following this, if the keys are repeatedly pressed again, the brightness will be minimized, thereby lowering the power consumption. Adjust the brightness (dark) with Fn + F2

operations. HDD Motor Timeout: When the hard disk drive is not accessed for more than a minute, power to the motor is shut off. CDD Motor Timeout: When the CD-ROM drive is not accessed for more than a minute, power to the motor is shut off. Standby Timeout: When the computer is idle or a device is not accessed for one or two minutes, the computer enters the standby mode. Power Management settings ( page 26) * Setting at the time of purchase ** Enabled only when the battery itself is being used. Advanced Standard Standard OFF (Battery/AC adapter)* (Battery)** CPU Speed Change Mode Enable Enable Enable Disable HDD Motor Timeout 1 min 1 min 1 min Never CDD Motor Timeout 1 min 1 min 1 min Never Standby Timeout 1 min 2 min 2 min Never Power Management Functions automatically set Close the Setup Utility ( page 24) 6 1 Run the Setup Utility ( page 24) 3 Using and , select [Power Saving], then set [Advanced] with 4 Using and , select [Power Switch], then set [Suspend] or [Hibernation] with 5 Using and , select [Suspend/Hibernation Timeout], set either [4 min] or [16 min] with , then press Esc 2 CAUTION Setting Power Management (How to set [Advanced] and the suspend/hibernation timeout) Using and , select [Power Management], then press Enter Computing On the Road (To avoid setting the suspend/hibernation timeout, press Esc and proceed on to step 6.) There are times when high-speed communication is adversely affected if the power man- agement function is enabled. Please confirm that is displayed by pressing Fn + F8 to disable the power management function. After you have finished using a communication device, you can enable the power management function by pressing Fn + F8 . Key operation and music playback. When the power management function is running, you may feel that key and trackball (or mouse) operations are sluggish. Furthermore, music may not be played back correctly when entering the standby mode during playback. When installed in a network environment. Be sure to disable the suspend/hibernation timeout settings with the Setup Utility . After resuming operation from the suspend or hibernation mode, the network connection may be severed or the computer will not work properly. When a device like a high-speed modem or ISDN terminal adapter is connected to the serial port, etc.

Battery Status Battery Indicator Battery Status Charging Fully-charged Battery charge is low (the charge is less than approx. 9% capacity) Battery pack or charger may not be working properly. Quickly remove the battery pack and disconnect the AC adapter, then connect them again. If the problem persists, contact Panasonic Technical Support. Unable to recharge due to violation of temperature limits Battery pack is not connected or charging not being performed. Orange* Green* Red Blinking red* Blinking orange for 5 seconds after the AC adapter is connected* Not lit * When the AC adapter is connected. Following that: Plug in the AC adapter, and fully charge your battery. Use a spare battery if you have one. If you have neither the AC adapter nor an extra battery, power the computer off. If the suspend or hibernation function is set Computer goes off (at approx. 0% capacity) If the suspend or hibernation function is not set (at approx. 9% capacity) Red indicator lights Beep sounds** (at approx. 9% capacity) Red indicator lights Beep sounds** (at approx. 4% capacity) ** When disabling the speakers with the Setup Utility (or pressing Fn + F4 ), the warning beep is also disabled. Getting a detailed reading NOTE (at approx. 4% capacity) save your data and power off your computer Suspend Mode or Hibernation Mode When the Remaining Battery Charge Becomes Low Fn + F9 The actual remaining battery life and the displayed indication may differ. In this case, the battery will need to be recharged. The following are indications of a battery that needs to be recharged: The battery indicator light remains red for a long period of time. The battery remaining displays 99% and the indicator light is orange for a long pe- riod of time. Low battery warning appears after a short period of time*. * This may be caused by the use of suspend mode for long periods of time. The Battery is discharging while the unit is in suspend mode when the AC adapter is not connected. If any of the above condition occurs, the battery must be discharged, then recharged. You should use the computer without power connected until the battery is fully discharged (reaches 0%) or the displayed battery life falls below 94%. Reconnect the AC adapter to fully recharge the battery. When the battery pack is not in the computer, is displayed.

after fully charging according to the instructions, it may be time to replace your battery pack. The battery pack is a consumable item and therefore will require replacement (CF-VZS251AW). Replacing the Battery Pack 2 Taking out the battery pack 1 CAUTION In the suspend mode, do not remove/change the battery pack. Removing the pack in the suspend mode will erase your data and may damage the computer. Power off your computer ( ) Do not shut down using the suspend mode. Open the cover 3 Close the cover 4 Although the battery has not begun to run out, the battery indicator may light up red or emit a beep. This indicates a significant rise in the temperature of the battery pack. This is typically caused by the fact that the battery pack has been delivering a high level of power because the computer has been used with the display at the brightest setting and with the power-saving function off. To protect the battery pack from increases in temperature, the brightness of the display automatically decreases, allowing the temperature of the battery to drop. In this condition, if the computer is left as is, it will automatically go off after about three minutes have elapsed. Within that period, therefore, be sure to connect the AC adapter or shut the computer OFF after saving any open data (if necessary). NOTE Battery Power Lever CAUTION Cover Connector Battery Pack CAUTION CAUTION Do not touch the terminals on the battery pack. The battery pack may no longer function properly if the contacts are dirty or damaged. The battery pack is not charged when the computer is first purchased. Be sure to charge it before using it for the first time. When the AC adapter is connected to the computer, charging begins automatically. Turn the computer over, unlock the lever and then open the cover. As shown in the figure, lift the battery pack and remove it from the connector. Inserting a battery pack Reconnect the battery to the connector and return it to its proper location. Be sure the battery pack is properly con- nected to the connector. Close the cover using the arrow as a guide, then lock the lever into place. Confirm that the lever lock is correctly in place. Should you decide to carry your computer without the lever lock in place, the cover may open causing the battery pack to fall out.

3 Turn your computer on There are some PC Cards that require a special or updated device driver be installed. Follow the instructions on the screen and read any related manuals on how to install device drivers. Installing a PC Card Simply slide the PC Card in until it snaps into place. Please refer to the manual for each card on how to install the card (insertion is typically label-side up). Label-side up Your computer has two PC Card slots. These slots conform to the PC Card Standard; therefore, communications and SCSI devices may be utilized. The slots allow you to use two Type I or Type II cards (or one Type I and one Type II), or one Type III card. Type I or II Two cards can be used simultaneously. Type III One card can be used only in the slot 1. CAUTION Please check the PC Cards’ specifications. Be sure the total operating current does not exceed the specified limit. Damage may result otherwise. Allowable Current (total for two slots) : 3.3 V: 400 mA, 5 V: 400 mA, 12 V: 120 mA There are times when both a Type I card and a Type II card will not work at the same time. When using a CardBus type PC card, the following cautions must be observed: When using a CardBus type card, no other types of cards can be used. When removing a CardBus type card (e.g., to insert a non-CardBus type card), be sure to restart the computer after pressing [Stop] ( below “To remove a PC Card”). After that, follow the procedure below on installing/removing a PC card. Removing a PC Card 2 CAUTION Power off your computer ( ) Do not shut down using the suspend or hibernation mode. 1 Do not install or remove peripherals while your computer is in the suspend or hibernation mode; abnormal operation may result. Pull the button out and press it. Pull the PC Card the rest of the way out. 1 2 CAUTION PC Card Installing/Removing the PC Card 1 2 Button CAUTION To remove a PC card: Before removing a PC Card, go to [Socket Status] (in [Start] - [Settings] - [Control Panel] - [PC Card (PCMCIA)]), select the PC Card slot and press [Stop]. After removing a CardBus type PC Card, be sure to restart the computer. When inserting a card, do not force the card in if doing so seems difficult. You may damage the slot, making it impossible to remove the card. Slot (Socket) 2 Slot (Socket) 1

PC Card Utility Program 1 Set [Sound Controller] to [Automatic (PnP)] in the Setup Utility. 2 Select [Start] - [Run]. 3 Type "c:\util\drivers\pccard\setup.exe", press [OK], then follow the on-screen instructions. About PhoenixCard ManagerTM for Windows® 95 CAUTION Follow the installation procedure below only if you will be using the ZV card. Otherwise, do not perform the installation; abnormal operation may result. If the hard disk has been reimaged, reinstall PhoenixCard ManagerTM for Windows® 95 if you will be using the ZV card. NOTE When running the power conservation function with the sound chip set, there may be no sound output. In this case, the following setting needs to be made. In [Control Panel] - [Power] - [OPL3-SAx power management], set [Non Power Save mode] then press [Apply]. Then press [OK]. CAUTION After PhoenixCard ManagerTM for Windows® 95 has been installed, make sure to power off the computer before installing or removing the card. Also, do not use the suspend or hibernation functions if the card is installed. Installing (only if you will be using the ZV card) Uninstalling If you will not be using the ZV card, uninstall PhoenixCard ManagerTM for Windows 95 in [Start] - [Settings] - [Control Panel] - [Add/Remove Programs] and follow the procedure below after restarting the computer. 1 Select [PC Card (PCMCIA)] in [Start] - [Settings] - [Control Panel]. 2 Press [Next] at the display for the [Display Driver Wizard for PC Cards (PCMCIA)], press [Next] again and then press [Finish]. When the message appears asking whether to reboot the computer, select [Yes].

it. Installing the RAM module CAUTION RAM modules are extremely sensitive to static electricity. There are cases where static elec- tricity generated by the human body has adversely affected such modules. In addition, it is easy to damage the RAM modules or internal components of the computer. Therefore, when installing or removing a RAM module, handle the module with extreme care. Installing/Removing the RAM Module Do not shut down using the suspend or hibernation mode. 1 Power off your computer ( ) Do not install or remove peripherals while your computer is in the suspend or hibernation mode; abnormal operation may result. CAUTION CAUTION Do not touch the terminals or internal components, insert objects other than the module, or allow foreign particles to enter. Doing so has been known to cause damage, fire or electric shock. 2 RAM module specifications 144 pins, 60/70 ns, 3.3 V SO-DIMM, EDO Removing the RAM module Open the left and right hooks. Gently remove the RAM module from the slot. 1 2 Remove the cover Adding Memory RAM Module 3 Hard Disk Drive RAM Module Slot RAM Module Hook Lever Finger location Cover Take care not to remove the connector Gently return the hard disk into the slot, and then slide the cover back on Be sure to lock the lever. ( page 23, Step 4 and 5) CAUTION Be careful when handling the hard disk. The hard disk is extremely sensitive to shock. Turn the computer over, unlock the lever and then slide the cover off. Flip over the hard disk Do not disconnect the hard disk from the connector, and let it remain on the frame. (Support the hard disk by hand.)

hassles of having you connect/disconnect the various cables when carrying your computer around and allows a variety of peripherals to be connected including a headphone or microphone, etc. The port replicator connects to the expansion bus connector on the bottom of your com- puter. When your computer is not connected to the port replicator, be sure that the expansion bus connector on the bottom of the computer is covered. For more detailed information, please refer to the operation manual for the port replicator. Port Replicator CAUTION When using the computer with the port replicator, the microphone, headphone, and USB connectors must be connected to the port replicator, not directly to the com- puter.

CAUTION Do not install or remove peripherals while your computer is in the suspend or hibernation mode; abnormal operation may result. Do not shut down using the suspend or hibernation mode. Power off your computer ( ) Turn on the printer, then turn on your computer with the LCD panel opened 3 Setting your printer Go to [My Computer] - [Printers]. Find your printer’s icon, double-click on it, and click [File] - [Set As Default]. If no icon is available, select [Add Printer] and then follow the on-screen instructions. 4 You may need to install a driver for your printer. Simply follow the on-screen instruc- tions and refer to the operation manual for the printer on how to install the driver. Parallel Port NOTE Using a Printer

hibernation mode; abnormal operation may result. 2 Connect the external display to your computer Do not shut down using the suspend or hibernation mode. Power off your computer ( ) Run the Setup Utility ( page 24) Using and , select [Display], select the display with , then press Esc Using and , select [System Setup], then press Enter Close the Setup Utility ( page 24) Turn on the display, then turn on your computer with the LCD panel opened 3 1 2 3 4 Ext. Display Port Using an External Display Select your external display 4 Set your external display for [Monitor] in [Start] - [Settings] - [Control Panel] - [Dis- play] - [Settings] - [Advanced Properties]. When a monitor that does not conform to the Plug & Play standards is connected, select [Change] and make the monitor settings. You can choose to select either an external display, or the LCD, or both with Fn + F3 . In addition, you can set the display to use during start-up with the following procedure. NOTE For more detailed information, please refer to the operation manual of the external display.

hibernation mode; abnormal operation may result. 2 Connect the USB device to your computer Do not shut down using the suspend or hibernation mode. Power off your computer ( ) NOTE For more detailed information, please refer to the operation manual of the USB device. Run the Setup Utility ( page 24) 3 Using and , select [Supervisor Setup], then press Enter Using USB Devices USB Connector 4 5 Using and , select [USB Controller], set [Enable] with , then press Enter Using and , select [Power Management], then press Enter 6 7 Using and , select [Power Saving], set [OFF] Close the Setup Utility ( page 24) 9 CAUTION When using a USB device, do not use the suspend or hibernation function. In addition, do not use the standby mode by pressing Fn + F10 . If by accident the suspend, etc., function is used, the computer may act abnormally. In this case, restart the computer by pressing the reset button. You may need to install a driver for your USB devices. Simply follow the on-screen instructions and refer to the operation manual for USB devices on how to install the driver. 8 Using and , select [Power Switch], set [ON-OFF] with , then press Esc

Your computer is equipped with an infrared communications port enabling you to transfer data without a cable. Preparations for Infrared Data Communications Set the address of your infrared communications port to enable. ( below) Position your computer so that the port is face-to-face with the port of another computer. Be sure the computers are not in direct contact with one another. A port-to-port distance of 20 to 50 cm (8 to 20 inches) is recommended. Problems with infrared data communications An object is located between both ports. There are other electronic devices nearby causing interference, such as a television, VCR, wireless headphone, etc. Direct sunlight or white glowing light, such as fluorescent lighting; can cause inter- ference with communications between the ports. When moving your computer while it is transmitting/receiving data. Setting for Infrared Data Communications 3 2 1 Run the Setup Utility ( page 24) Using and , select [Supervisor Setup], then press Enter Using and , select [IrDA], set [2F8] with , then press Esc Close the Setup Utility ( page 24) 4 3 2 1 4 Select [Start] - [Programs] - [Accessories] - [Direct Cable Connection] Select [Host] or [Guest], then press [Next] Select [Serial cable on COM4], then press [Next] Press [Finish] NOTE If [Serial cable on COM4] is not displayed, select [Install New Ports]. Data Communications Infrared data communications will begin. To process at a transfer speed of 4 Mbps, separate application software is necessary. When you select [Start] - [Settings] - [Control Panel], and then select [Infrared], this will give you the conditions for infrared data communications. Online help is available on how to use Direct Cable Connection.

To change your hard disk, contact Panasonic Technical Support 3 Removing/Installing the hard disk 2 1 Do not shut down using the suspend or hibernation mode. Power off your computer ( ) 4 CAUTION Do not install or remove peripherals while your computer is in the suspend or hibernation mode; abnormal operation may result. CAUTION To customers: To change your hard disk, consult your nearest Panasonic Technical Support. Be sure to back up all important data before the change. To technicians (at Panasonic Technical Support): Be careful when replacing the hard disk. The hard disk is extremely sensitive to shock. In addition, static electricity could later affect some internal components. Installing/Removing the hard disk (For technicians at Panasonic Technical Support) Put the cover back into place Take off the cover Turn your computer over. Then, slide the cover and remove it. Tape Return the hard disk to the slot very gently Connector Cover Lever 5 For information on FAT32, refer to "Technical Information" ( page 30). To dislodge the hard disk, after flipping it over, pull on the tape . When installing a hard disk, be sure to hold the connector part. Be sure to lock the lever.

need to restart your computer. NOTE The Setup Utility will not be run if F1 is not pressed soon after the computer restarts. In this case, you need to restart your computer again. If is displayed, enter your password. If both the [User Password] and [Supervisor Password] have been set, after entering the User Password, [Supervisor Setup] and [Load Default Setting...] will not be displayed on the main screen. To display the [Supervisor Setup]: 1 Restart the computer and press F1 when [Press F1 for Setup] is displayed. 2 When is displayed, enter the Supervisor Password. For more details, on-line help is available; press F1 . Running the Setup Utility Press F1 for Setup Upon seeing this message Setup Utility •System Setup •Power Management •Supervisor Setup Save Settings Restore Settings Load Default Settings (PnP) Load Default Settings (Non-PnP) Exit Setup Set default settings. • (PnP) denotes “for Windows® 95”. • (Non-PnP) denotes “for other than Windows® 95”. • When the Supervisor Password has been set, input of the password is necessary.

Closing the Program Exit Setup Settings were changed. Do you want to save them? Yes, save and exit the Setup Utility. No, exit the Setup Utility without saving. No, return to the Setup Utility. (The display may be different if no changes to the settings are made.) Key Operations NOTE F1 : To display the corresponding “help” file. Enter : To make a selection. Esc : To display previous screen (To exit the program at the main screen). : To move among the items. : To move among the values of each item. F9 : To return to the setting before a change. F10 : To set the default values. NOTE If the User Password has been set, the password must be en- tered before Windows can start. Return to the state existing at the time of Setup Utility startup, or to the settings saved with [Save Settings]. Select one of the items and press Enter . F1

Enable Disable Alt + Ctrl + F9 Alt + Ctrl + F10 Alt + Ctrl + F11 Alt + Ctrl + F12 Parameters NumLk Track Ball Speaker Display User Password Coffee break Password* Key Combination for Coffee break** * Cannot be selected when the user password setting is not allowed due to the supervisor setting. ** Can only be selected when the [Coffee break Password] has been set. System Setup System Setup NumLk [ON] Track Ball [Enable] Speaker [Enable] Display [External Monitor] •User Password Coffee break Password [Disable] Key Combination for Coffee break [Disable] Setup Utility (Underlined item: Default)

CPU Speed Change Mode Enable HDD Motor Timeout 1 min CDD Motor Timeout 1 min Standby Timeout 2 min Power Switch [Hibernation] Suspend/ Hibernation Timeout [4 min] Setup Utility Advanced Standard (Battery/AC adapter) Standard (Battery) OFF Display Setting (Enable / Disable) Display Setting (1 min / Never) Display Setting (1 min / Never) Display Setting (1 min / 2 min / Never) Hibernation Suspend On-Off* Disable 4 min 16 min Power Saving CPU Speed Change Mode HDD Motor Timeout CDD Motor Timeout Standby Timeout Power Switch Suspend/Hibernation Timeout** Enable Enable Enable Disable 1 min 1 min 1 min Never 1 min 1 min 1 min Never 1 min 2 min 2 min Never Enable Enable Disable Disable CPU Speed Change Mode HDD Motor Timeout CDD Motor Timeout Standby Timeout Power Conservation (AC Adapter Connected) Popup Window Advanced Standard (Battery/AC adapter) Standard (Battery) OFF ** Setting at the time of purchase. ** Can only be selected when the [Power Switch] has been set [Suspend] or [Hibernation]. Power Management Parameters Power Management Settings (Underlined item: Default)

Parallel Port Mode Serial Port Sound Controller Sound Blaster Compatible I/O WSS CODEC I/O * Can only be selected when the [Sound Controller] has been set [Disable]. Supervisor Setup Supervisor Setup Parallel Port (Address) [Automatic (PnP)] Parallel Port Mode [Bidirectional] Serial Port [Automatic (PnP)] Sound Controller [Enable] Sound Blaster Compatible I/O [Automatic (PnP)] WSS CODEC I/O [Automatic (PnP)] Sound IRQ-A [Automatic (PnP)] Sound IRQ-B [Automatic (PnP)] Sound DMA-A [Automatic (PnP)] Sound DMA-B [Automatic (PnP)] IrDA [Automatic (PnP)] Floppy Operation [Enable] CD Operation [Enable] Boot Up Drive [FDD HDD] •Supervisor Password User Password Protection [Disable] USB Controller [Disable] Setup Utility Parameters (PnP: Default underlined; Non-PnP: Default in Italic)

HDD -> FDD CDD -> FDD -> HDD Enter displays the supervisor password menu. Enable Disable Enable Disable Sound IRQ-A Sound IRQ-B Sound DMA-A Sound DMA-B IrDA Floppy Operation** CD Operation Boot Up Drive Supervisor Password User Password Protection*** USB Controller * Can only be selected when the [Sound Controller] has been set [Disable]. ** Cannot be selected when [Boot Up Drive] is set to [FDD -> HDD]. *** Cannot be selected when both [User Password] and [Supervisor Password] are the same. Setup Utility

mode. Be sure to disable the suspend/hibernation timeout settings with the Setup Utility if you require a network environment. When the power saving function is running, communications software may malfunction. For example, communications may be halted if the suspend or hibernation mode is activated. Be sure that the computer enters the standby or suspend (hibernation) mode after the commu- nications software is closed. The computer must be restarted if one of these modes is entered during data communications. Network

Enter "FDISK", then press Enter . When [Do you wish to enable large disk support (Y/N)...?] appears on the screen, press “N”, then Enter . Select [3. Delete partition or Logical DOS Drive]. Select [1. Delete Primary DOS Partition]. Start up again following the instructions on the screen. These steps will allow you to install most operating systems. The contents of the hard disk will be deleted. Always make sure to back up the hard disk beforehand. The following steps will normally be unnecessary, however, if installation is not possible, try performing them. Start up again using the FIRSTAID FD to open FDISK in the same way. When [Do you wish to enable large disk support (Y/N)...?] appears on the first screen, press “N”, then Enter . Select [1. Create DOS partition or Logical DOS Drive]. Set the partition following the on-screen instructions and activate it. Start up again following the on-screen instructions. Back up the contents of your hard disk. Insert the FIRSTAID FD, and restart the computer. This computer uses a new, highly efficient file system called FAT32. Please note the following regarding FAT32. Some software will not run normally: Do not run disk utilities and other software not compatible with FAT32. Doing so could cause incorrect information such as hard disk capacity to be shown or could destroy hard disk data. Contact the dealer or other outlet for the software and obtain the latest version. Non-recognition from other operating systems: You will not be able to view the contents of your hard disk from other operating systems. (For example, you will not be able to view the contents of your hard disk even when starting up using a floppy disk created with another computer.) Other operating systems cannot therefore be installed. To install the operating system, please refer to the method listed below. If you are unsure about this explanation, do not proceed with installation of operating system. 1 2 Hard Disk 3 4 5 6 7 8 9 10 11 12 Technical Information FAT32

displayed. After reinstalling Windows, [Previous version of MS-DOS] also appears in this menu, however, do not select this item as MS-DOS is not installed. Reinstallation The sound chip has its own power saving function. You can enable this function in the [OPL3- SAx power management] tab (select [Start] - [Settings] - [Control Panel] - [Power] - [OPL3-SAx power management]). In [Non Power Save mode], the power saving function is disabled. (When a ZV card is used, set [Non Power Save mode] to enable sound to be normally produced. This is the default setting.) In [Minimum level of power save], the power saving function is enabled. You may encounter problems, such as no sound from music CDs. Do not select [Intermediate level of power save] or [Maximum level of power save] because noise is likely. Power Saving Function in the Sound Chip Internet Explorer 4.01 places a tremendous load on the system in order to execute the wide variety of functions that it provides. As a result, some unexpected faults may occur. If any of these faults occurs, try using the software with some Internet Explorer 4.01 functions turned off. (See Internet Explorer Help for more details.) It takes a long time to reboot or the computer locks up. Delete the check mark for [Internet Explorer Channel Bar] in [Control Panel] - [Display] - [Web], then press [OK]. A system module error occurs. Set [ (None)] for [Wallpaper] in [Control Panel] - [Display] - [Background]. Performing the above steps does not solve the problem. Uninstall Internet Explorer 4.01 with the following step. Select [Microsoft Internet Explorer 4.01] in [Start] - [Settings] - [Control Panel] - [Add/ Remove Programs] - [Install/Uninstall] and press [Add/Remove]. Follow the on-screen in- structions. If a window with the message [Version Conflict] appears during the installation pro- cess (network card and application installation), select [Yes]. Proper operation may not be possible if [No] is selected. Internet Explorer

If a problem occurs with your hardware, and [POST Start up Error(s)] is displayed along with the error code(s), follow the on-screen instructions. Setup: Setup Utility ( page 24) is started. Run [Load Default Settings (PnP)]. Rerun the Setup Utility to input the appropriate operating environment settings. Exit: Ignore the error message(s), and restart the computer. Follow the messages on the screen. At the MS-DOS prompt (A:\WINDOWS\COMMAND>), input the following: diag45 Enter 1 To run the program, insert the FIRSTAID FD you created into the floppy disk drive, then turn your computer on 2 3 Using the Self-diagnosis Program Follow the procedure below to check whether each part of your computer is operating properly. 062 Boot failure--default configuration used Default configuration in use 101 System Board Failure Interrupt controller failure 102 System Board Failure Timer 2 test failure 106 System Board Failure Diskette controller failure 114 Adapter ROM Error Adapter ROM checksum error 151 System Board Failure Real-time clock failure 161 Bad CMOS Battery Dead battery 162 Configuration Change Has Occurred Configuration error 162 Configuration Error CMOS checksum error 163 Date and Time Incorrect Real-time clock is not updating 173 Configuration Change Has Occurred ROM configuration has changed 201 Memory Size Error Memory size/data error 301 Keyboard Error Keyboard failure 303 Keyboard Error Keyboard controller failure 604 Diskette Drive Error Diskette drive 0 failure 605 Diskette Drive Error Diskette unlocked problem 1780 Hard Disk Error Fixed disk 0 failure 1800 PCI Error No more IRQs available 1801 PCI Error No more room for optional ROM 1802 PCI Error No more I/O space available 1803 PCI Error No more memory (above 1 MB) available 1804 PCI Error No more memory (below 1 MB) available 1805 PCI Error Checksum error or 0 size optional ROM 1962 An operating system could not be found 8603 Pointing Device Error Pointing device failure I9990301 Hard disk failure I9990305 An operating system could not be found Code Description Select [1] from the menu

The screen shown below is displayed. When you click on an item, detailed information on that item will be displayed. Running DMI Viewer 2 1 Save the item that is displayed Select [Save Selected Data] from the [File] menu. Save all items Select [Save All Data] from the [File] menu. This computer conforms to the specifications of the Desktop Management Interface (DMI). The DMI Viewer can be used when you want to know information on the internal systems this computer supports, starting with the CPU and memory. Click to close the DMI Viewer Saving information to a file Displayed information can be saved to a text file (*.txt). Run the DMI Viewer and display the information you wish to save. Input the file name (and select the folder), then press [Save]

When a problem occurs, please refer to this page. The "Reference Manual" also contains detailed information. If a problem appears to be related to a software application, read the software related manual. If you still cannot troubleshoot the problem, please contact Panasonic Technical Support. Starting Up The power indicator or bat- tery indicator is not lit is displayed [POST Start Up Error(s)] is displayed The pre-memory count, Windows startup, or an op- eration is extremely slow The date and time are incorrect When the previous item is not the cause Check the cable connection for the AC adapter. Check to see if a fully charged battery is properly installed. Pressing the reset button ( ) will solve the problem. Remove the battery pack and disconnect the AC adapter, then connect them again. Please input your password. If you have forgotten it, contact Panasonic Technical Support. page 32 Run [Load Default Settings] (PnP) in the Setup Utility ( page 24). This will restore the Setup Utility's settings to their default values (except the password settings). Then, the Setup Utility must be run once again for you to input the appropriate operating environment settings. (The processing speed depends on the application software used, so this operation may not cause the processing speed to increase.) You can set the date and time through [Date/Time] in [Start] - [Settings] - [Control Panel]. If you continue to experience problems, the internal battery maintaining the clock may need to be replaced. Please contact Panasonic Technical Support. Run [Load Default Settings] (PnP) in the Setup Utility ( page 24). This will restore the Setup Utility's settings to their default values (except the password settings). Try removing all peripheral devices. In the MS-DOS mode, run SCANDISK to check the hard disk. At start-up, press F8 to operate the computer in the Safe mode. The red battery indicator lights. Repeated beeps sound while the computer is in use. The red indicator blinks After the AC adapter is con- nected, the orange indicator blinks five times The battery level is low. Save your data and power off your computer. After connecting the AC adapter or replacing the battery pack with a fully charged one, turn your computer on. The battery pack or recharging function may be defective. Quickly remove the battery pack and disconnect the AC adapter, then connect them again. If the problem persists, contact Panasonic Technical Support. Unable to charge because of an improper temperature range. ( ) Battery Indicator

Cannot read/write to a floppy disk Unable to write to a floppy disk How to format a floppy disk is unclear Unable to read/write to the hard disk Trouble has occurred with the CD When the previous item is not the cause The access lamp ( ) does not light Cannot play CD or read data from it Cannot eject CD The CD-ROM drive vi- brates a lot Disk Operations Has the floppy disk been correctly inserted? Has the floppy disk been correctly formatted? Has the Setup Utility been used to set [Floppy Operation] to [Enable]? ( page 27) Is the floppy disk write-protected? Select [Format] in [My Computer] - [3 1/2 Floppy (A:)] - [File]. After confirming the disk volume and format type, start formatting. Your drive or file may not have been properly set. Check to see if the hard disk is full. If it is full, delete unnecessary files. Your hard disk content may be corrupted. Contact Panasonic Technical Support. You may need to clean the lens or CD; Try testing another drive or media. Is the CD loaded on the tray correctly? Is the CD bent, scratched, or dirty? Is the computer powered on? To remove a CD when the computer is powered off, insert a sharp object such as the bent-out tip of a paper clip into the emergency hole. Pushing it completely to the end will free the tray so that it can be pulled out. Is the CD bent or labeled? No display after powering on The power has not been cut, but after a certain period of time, there is no display An afterimage appears The motion of the mouse cursor is not smooth At the time of purchase, the display setting is preset for an external display. If you connect an external display, the screen is displayed on the external display. When there is no display to an external display, • Check your cable connection to the external display. • Confirm your display is powered on. • Check the settings for your external display. Try changing the display by pressing Fn + F3 . If your computer is connected to an external display and the internal LCD has been set to "off", and the computer is placed in the hibernation or suspend mode, the internal LCD will remain in the "off" mode if the external display is not connected when the computer is restarted. In this case, re-connect the external display and reboot the computer. Has the computer been set to the power-saving mode? To resume operation of your computer, press any key, or move the trackball or mouse. To save power, your computer may have automatically entered the suspend or hiberna- tion mode. ( page 11) If an image is displayed for a prolonged period of time, an afterimage may appear. This is not a malfunction. The afterimage will disappear when a different screen is displayed. Select [Start]-[Settings]-[Control Panel]-[Mouse]-[Motion] and check [Show pointer trails]. Display Emergency Hole

but numerals Only capital letters are being input How to input European characters (ß, à, ç) or symbols is unclear If NumLk and Key Pad are on, the Numeric Key Pad is ON. To switch it OFF, press Fn + Key Pad . If CapsLock is on, the Caps Lock function is ON. To switch it OFF, press Caps Lock . Select [Start] - [Programs] - [Accessories] - [Character Map]. The Character Map will be displayed. Point to the desired font name and select it. Dealing With Problems is displayed [Supervisor Setup] is not displayed in the menu [User Password] cannot be selected [Coffee break Password] or [Key Combination for Coffee break] cannot be selected [Supervisor Password] cannot be set Setup Utility Enter the User Password or Supervisor Password. If you have forgotten it, contact Panasonic Technical Support. At the start of the computer when is displayed, you have to enter the Supervisor Pass- word. When both the User Password and Supervisor Password have been set, if you enter the User Password, [Supervisor Setup] will not be displayed. If [Supervisor Setup] is not displayed even after entering the Supervisor Password, you have to delete the User Password. Run the Setup Utility again, and input the Supervisor Password. [User Password Protection] in [Supervisor Setup] may be enabled. You need to set the User Password. If the User Password has been set first, the Supervisor Password can not be the same as the User Password. Another password needs to be entered.

work (An error occurs while installing the driver) Unable to print The cursor does not move from mouse operations The device connected to the serial port does not work External mouse or trackball connected to the ext. key- board/mouse port does not work A PC Card does not work You do not know the available RAM module The RAM module has not been recognized The address map for IRQ, I/O port address, etc. is unclear A USB device does not work You need to use drivers conforming to OS*. Some earlier drivers will no longer work. For more information, please ask the manufacturer of the driver in question. * Windows® 95 Version 4.00.950C (OSR-2.5) Check the computer-printer connection. Make sure the printer is on. Make sure the printer is in the online state. Make sure paper is in the printer tray and there is no paper jam. Has the Setup Utility been used to set [Parallel Port (Address)] to [Automatic (PnP)], [378] or [3BC]? The Coffee break Password may be set; check if is displayed. If this is the case, input the Coffee break Password. Check your mouse connection, then reboot the computer from the keyboard. From the keyboard, you may choose to press down on , then select [Shut Down]. Check the connection. Confirm that the device driver for the serial port works. Please refer to the reference manual of the device. Confirm that two mouse devices are not connected, one through the ext. keyboard/mouse port and the other through the serial port. Try setting [Trackball] to disable in the Setup Utility. Has the Setup Utility been used to set [Serial Port] to [Automatic (PnP)] or [3F8]? Try setting [Trackball] to disable in the Setup Utility. In some circumstances, if a PS/2 external mouse with a serial interface conversion func- tion is connected to the port, it may not operate normally. Try connect it to the serial port. Make sure the card is properly inserted. Confirm that the card conforms to the PC Card Standard. Note that after a driver is installed, the computer must be rebooted. Check that the proper port settings have been made. Read the PC Card’s manual. Or, you may need to call the manufacturer of the PC Card. If you will be using a ZV card, please install PhoenixCard ManagerTM for Windows® 95. ( page 16) page 17 Make sure the RAM module has been properly inserted. Check the address map by going to [View Resources] in [Start] - [Settings] - [Control Panel] - [System] - [Device Manager] - [Computer] - [Properties]. Has the Setup Utility been used to set [USB Controller] to [Enable]? Make sure a driver is installed. Contact the manufacturer of the product. Dealing With Problems Connecting Peripherals

Rerun the application program after the computer restarts. If the program no longer works normally, go to [Start] - [Settings] - [Control Panel] - [Add/Remove Programs] to delete the program. Then, try installing the program once again. Dealing With Problems Computer Hangs Application Software When using the computer as a network computer, some additional settings may have to be made depending on the usage conditions. We recommend asking your system administrator or the person in charge of the network. Unable to connect to a network Network

reproduced in any form without the prior written permission of Matsushita Electric Industrial Co., Ltd. No patent liability is assumed with respect to the use of the information contained herein. ©Matsushita Electric Industrial Co., Ltd. 1998. All Rights Reserved. Disclaimer Computer specifications and manuals are subject to change without notice. Matsushita Electric Industrial Co., Ltd. assumes no liability for damage incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manuals. Trademarks PS/2™ is a trademark of International Business Machines Corporation. Microsoft®, MS-DOS®, Windows® and Windows NT® are registered trademarks of Microsoft Corporation of the United States and/ or other countries. PhoenixCard Manager™ and Phoenix Card Executive™ are trademarks of Phoenix Technologies Ltd. Acrobat® is a registered trademark of Adobe Systems Incorporated. Panasonic® is a registered trademark of Matsushita Electric Industrial Co., Ltd. A