Sonic Impact Technologies IP-P22 Operation & User’s Manual

FCC Declaration of Conformity Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radio and Television Interference This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and then on, the user is encouraged to try to correct the interference by one or more of the following measures: • Increase the separation between the equipment and receiver. • Connect the equipment to a different outlet so that the equipment and receiver are on different branch circuits. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by Sonic Impact could void the user’s authority to operate the equipment. THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. Sonic Impact Technologies LLC ©Sonic Impact Technologies LLC 2555 State Street iP-22 is a trademark of Sonic San Diego, California 92101 Impact Technologies LLC USA iPod® is trademark of Apple Computer, Inc., registered in the www.si-technologies.com U.S. and other countries

CAUTION: TO PREVENT ELECTRONIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD.RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS I-FUSION TO RAIN OR MOISTURE IMPORTANT iP-22 SAFETY INSTRUCTIONS 1. Read instructions --All Safety and operating instructions should be read before the iP-22 is used. 2. Retain instructions--The operating instructions should be retained for future reference. 3. Heed warnings--All warnings in the operating instructions should be read and adhered to. 4. Follow instructions--All operating instructions should be followed. 5. WARNING: Avoid water and moisture--Keep away from all liquids. To reduce the risk of fire or electric shock, do not expose the iP-22 to rain or moisture. 6. Location--The iP-22 should be placed in a stable, level location, away from external heat sources and with adequate ventilation. Do not expose the iP-22 to temperature or humidity extremes. Protect from exposure to dirt, sand, and dust. Note that the speakers are magnetically shielded to prevent distortion of TVs and computer monitors, but keep magnetic storage media at least four inches from the iP-22 to avoid data loss. 7. Power supply--When not powering off the internal rechargeable battery, the iP-22 should only be connected to the power supply provided with your unit or as described in the operating instructions and as marked on the iP-22. 8. Power cord use and care--Power cords should be located so that they are not likely to be walked on or crushed by placing other objects on top of them. Check all attachments regularly. Do not bypass the proper grounding or polarization of the power plug. If your iP-22 is not to be used for an extended period of time, unplug and stow the power cord. 9. TO PREVENT THE RISK OF ELECTRIC SHOCK AND DAMAGE TO THE UNIT, DO NOT REMOVE THE SPEAKER GRILLES OR OPEN THE UNIT FOR SERVICING EXCEPT TO REPLACE THE RECHARGEABLE LITHIUM ION AS INSTRUCTED IN THIS MANUAL. PLEASE REFER SERVICING TO QUALIFIED SONIC IMPACT PERSONNEL. 10. Cleaning--Use only a soft dry cloth. Do not use cleaning chemicals of any kind.

12. Accessories--Only use attachment accessories specified by Sonic Impact Technologies. 13. Damage Requiring Service--The iP-22 should be serviced by qualified service person when: · The power-supply cord or the plug has been damaged. · Objects have fallen onto or liquid has been spilled into the i-Fusion. · The iP-22 has been exposed to rain. · The iP-22 does not appear to operate normally or exhibits a marked change in performance. · The iP-22 has been dropped or the enclosure has been damaged. 14. Servicing--The user should not attempt to service the iP-22 themselves. Servicing should be referred to a qualified service person or returned to the dealer. For questions about warranty and service call Sonic Impact Technologies, LLC at [email protected] . ONE-YEAR LIMITED WARRANTY Sonic Impact Technologies warranties that all of its products are free from defects in material and workmanship in the course of normal and reasonable use for a term of one year from the date of purchase. This warranty is the exclusive and only warranty in effect relative to Sonic Impact Technologies powered iP-22 speaker system and any other warranties, either expressed or implied, are invalid. Neither Sonic Impact Technologies, LLC nor any authorized Sonic Impact Technologies, LLC reseller are responsible for any incidental damages incurred in the use of the speakers. (This limitation of incidental or consequential damage is not applicable where prohibited.) Sonic Impact Technologies, LLC’s obligation under this warranty does not apply to any defect, malfunction or failure as a result of misuse, abuse, improper installation, use with faulty or improper equipment or the use of the speaker systems with any equipment for which they were not intended. The terms of this warranty apply only if the iP-22 speaker systems are returned to the respective authorized Sonic Impact Technologies, LLC reseller where they were purchased. CUSTOMER SERVICE For service or warranty of the electronics please contact: [email protected]

Adapter Cable Sleeves Connect Instruction ·iP-22 portable speaker case ·9V 1.2A AC power adapter ·Ø3.5 stereo cable ·iPod mini、iPod 3G 10GB15GB/iPod 4G 20GB/iPod PHOTO 30GB、iPod 3G 30GB/ iPod 4G 40GB/ iPod PHOTO 40GB60GB adapter sleeves ·User manual ·Quick connect instructions iP-22 Diagram：

2、 iPod®30 Pin Docking Station 3、 Speaker Driver Unit 4、 Port tube 5、 Battery compartment 6、 Input Jacks 7、 Rubber

9、 iPod® Adapter sleeve 10、 iPod®30 Pin Docking Station 11、 Power On/Off and LED LOCATING YOUR iP-22 SYSTEM Best to position the iP-22 system on a stable, level surface within 1-2.5 meter from the listener. The iP-22 system may be placed near video displays, such as TV sets and computer monitors, without causing distortion to the image. CONNECTING TO YOUR iP-22 Warning: Ensure that iP-22 system is in the POWER OFF mode before making any connections and before docking the iPod into the iP-22 system. To ensure proper operation, please carefully follow the connection sequence as described below and in the order indicated. Attach the iPod adapter sleeve, provided with your iP-22, that matches the model of your iPod. Each sleeve will be marked with the iPod models. An iPod model with a 30 PIN connector can be connected directly to the 30 pin docking station located on the iP-22 system. An older iPod model without a 30 PIN connector can be connected via the AUDIO IN port located at the side of your iP-22 case and by using the 3.5 mm stereo cable, included. When you’re sure that either method of connection has been made you are ready to play the iP-22 speakers. 4AA batteries must be inserted to the iP-22 or you may use the optional AC adapter power supply. POWER The iP-22 system uses a universal power supply via [email protected] power adapter or as a portable system uses 4 AA batteries as its power supply When the iPod is connected to the iP-22 system, insert the AC adapter barrel connector into the jack marked DC IN 9V , and then insert the universal power adaptor blade end into your AC power wall jack. Your iP-22 is ready to play. AA batteries power supply

instructions). Your iP-22 speaker system is now ready to operate. Remarks: The output of using power adapter is twice as great as the output of using battery When docked, your iPod will also recharge when using the AC adapter. START PLAYING 1、 Slide power switch to the right for “AUTO ON” and note that the power indicator will illuminate. 2、 Select and play your favorite music using your iPod。 VOLUME CONTROL The buttons on the front panel are the master volume controls for the iP-22 system. Press and hold “+” to increase the volume and then “-”to decrease the volume. The volume will start at 40% maximum volume position every time you re-start your iP-22 system. This will avoid disturbing others when booting it up. POWER OFF To minimize power consumption, please slide power switch to OFF when you are no longer using the device If your iP-22 is not to be used for an extended period of time, remove the AA battery from iP-22 .Please note that the iP-22 has an “ AUTO SHUT-DOWN (STANDBY) function which prevents excess power consumption during idle play. AUTO SHUT-DOWN (STANDBY) When the power switch is set at the “AUTO ON”position, the iP-22 system will shut down automatically and goes into standby mode if an audio signal is not detected within 5 minutes. The LED on the power switch will then turn

when an audio signal is detected and the iP-22 system will automatically power on. Power consumption will be reduced in this “standby” mode, but we suggest that you set the power switch to the “OFF” to shut down the iP-22 system completely when not in use for an extended period of time to save battery life. AA BATTERY REPLACEMENT While using AA battery as the power supply, the indicator turns green while the battery is full. When the indicator turns red , it is a warning that the battery is not full enough .The system will operate again after battery replacement. Under normal use, 4 AA battery can last at least 8 hours( depending on the volume setting and the play interval). Please note the following illustration to replace the AA battery.

Hi-Fi Neodymium driver, digital amp, and the latest digital equalizer circuitry

Slide the power switch to on position. Universal power cord isn’t plugged into a wall outlet and/or the power supply connector is not connected to the power supply jack on the back of iP-22 system。 Plug the universal power supply into a wall outlet and connect the power supply connector into the power supply jack on the back of the iP-22 system. Surge the protector (if used) isn’t powered on. If the universal power supply cord is plugged into a surge protector, make sure the surge protector is switched on. Wall outlet doesn’t work。 Plug another device into a wall outlet (same outlet) to confirm the outlet works Power indicator is not lit when the AC adapter is plugged in AA battery have no charge Replace the AA batteries. Verify the universal power supply cord is plugged into a wall outlet and he power supply jack on the back of the iP-22 system Speakers are mute iP-22 system is not switched on Verify batteries are installed if the universal power supply isn’t being used. Power Output ：1W*2 （AA battery power supply ） 2W*2 （power adapter supply） Speaker channel: 2 channel Impedance： 12Ω Frequency response ：180Hz-- 20KHz S/N ratio： 85dB±2 (0.5M & 1W) Driver unit：neodymium- magnetic drivers 1.25” × 2

indicator is illuminated.。 Press the “+” button to increase the volume。 Volume is set too low。 Check volume level on alternate audio source device and set it at mid-level。 iPod is not seated into the docking station Remove iPod and re-seat it in the docking station。 3.5 mm iP-22 stereo cable isn’t connected to an audio source Connect the 3.5 mm stereo cable to the audio source. Make sure the signal cable is inserted firmly into the correct jacks. 3.5 mm stereo cable is connected to incorrect output on audio source Make sure the 3.5 mm stereo cable is connected and fully inserted in the “line-our” “audio out” or the headphone jack on your sound card or other audio source A problem with audio source Test the speakers by using another audio source (e.g., portable CD, cassette player or FM radio) and by connecting the 3. 5 mm stereo cable through iP-22 Incorrect connection Check if iPod is properly seated in the docking station. Check connection of the 3.5mm stereo cable if not using the docking station. Make sure it is connected to “Line out”, “audio out”, or the headphone jack on your sound card or other audio source – and NOT “speaker-out”. Cracking sound from speakers。 A problem with your audio source Unplug the 3.5mm stereo cable from the audio source. Plug the cable into the headphone jack of an alternate source (e.g., Walkman, Discman or FM radio). Crackling sound from speakers (when connected to PC or laptop) Volume level in operating system is set too high. Check the operating system volume level and decrease it if necessary.

set too high. Decrease the volume Sound is distorted Sound source is distorted. WAV and MID files are often of poor quality; therefore distortion and noise are easily noticed with high-powered speakers. Try a different audio source such as a music CD Sound is distorted (when connected to PC or laptop) Volume level in operating system is set too high. Check the operating system volume level and decrease it if necessary. Sound isn’t continuous AA battery is not full Replace the AA battery or use power adapter Radio interference Too close to a radio tower。 Move your speakers to see if the interference goes away.