Graco 255348 Instructions Manual

SDP5 & SDP15 (Preset) Meters For metered dispense of oils and 50:50 antifreeze/water mix fluids. For professional use only. Not for use in explosive atmospheres. Maximum Working Pressure: 1500 psi (10 MPa, 103 bar) Maximum Working Pressure (50:50 antifreeze/water mix): 900 psi (6.2 MPa, 62 bar) Maximum Flow Rate:14 gpm (53 lpm) List of Models page 2 Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. NOTICE This dispense valve is designed to dispense petroleum-based lubricants and antifreeze only. Do not dispense windshield washer solvent with this dispense valve. ti11821 Preset Meter shown US Patent No: D594,490S India Patent No: 219652 Korea Patent No: 30-555779 Taiwan Patent No: D130836

SDM15 Manual Dispense Electronic Meters SDP5 Preset Dispense Electronic Meters Model Number Swivel Extension Description Nozzle Fluid Type 255348 1/2” npt(f) Flexible Extension Automatic, non-drip, quick close Oil 255349 1/2” npt(f) Gear Lube Extension None-drip, quick close Gear Lube 255350 1/2” npt(f) Rigid Extension Automatic, non-drip, quick close Oil 255802 1/2” npt(f) Rigid Extension Automatic, non-drip, quick close Anti-freeze 255803 1/2” npt(f) Flexible Extension Automatic, non-drip, quick close Anti-freeze Model Number Swivel Extension Description Nozzle Fluid Type 255800 3/4” npt(f) Rigid Extension Automatic, non-drip, quick close Oil 255801 3/4” npt(f) Flexible Extension Automatic, non-drip, quick close Oil 255836 1/2” npt(f) Rigid Extension Automatic, non-drip, quick close Oil 255837 1/2 npt(f) Flexible Extension Automatic, non-drip, quick close Oil Model Number Swivel Extension Description Nozzle Fluid Type 255200 1/2” npt(f) Rigid Extension Automatic, non-drip, quick close Oil 255351 1/2” npt(f) Flexible Extension Automatic, Non-drip, quick close Oil 255352 1/2” npt(f) Gear Lube Extension Non-drip, quick close Gear Lube 255355 1/2” npt(f) Rigid Extension Automatic, non-drip, quick close Anti-freeze 255356 1/2” npt(f) Flexible Extension Automatic, non-drip, quick close Anti-freeze

Model Number Swivel Extension Description Nozzle Fluid Type 255353 3/4” npt(f) Rigid Extension Automatic, non-drip, quick close Oil 255354 3/4” npt(f) Flexible Extension Automatic, non-drip, quick close Oil 256838 1/2” npt(f) Rigid Extension Automatic, non-drip, quick close OIl 256839 1/2” npt(f) Flexible Extension Automatic, non-drip, quick close Oil

tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable. WARNING SKIN INJECTION HAZARD High-pressure fluid from dispense valve, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment. • Do not point dispense valve at anyone or at any part of the body. • Do not put your hand over the end of the dispense nozzle. • Do not stop or deflect leaks with your hand, body, glove, or rag. • Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment. EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals. • Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS forms from distributor or retailer. • Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu- facturer’s replacement parts only. • Do not alter or modify equipment. • Use equipment only for its intended purpose. Call your distributor for information. • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. • Do not kink or over bend hoses or use hoses to pull equipment. • Keep children and animals away from work area. • Comply with all applicable safety regulations. BATTERY SAFETY The battery may leak, explode, cause burns, or cause an explosion if mishandled: • You must use the battery type specified for use with the equipment. • Sparking can occur when changing batteries. Only replace the battery in a non-hazardous location, away from flammable fluids or fumes. • Handle and dispose of battery properly - do not short circuit, charge, force over discharge, disas- semble, crush, penetrate, incinerate, or heat the battery to a temperature exceeding 185° F (85° C).

When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be aware that flammable fumes can ignite or explode. To help prevent fire and explosion: • Use equipment only in well ventilated area. • Eliminate all ignition sources, such as cigarettes and portable electric lamps. • Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline. • Do not plug or unplug power cords or turn lights on or off when flammable fumes are present. • Ground all equipment in the work area. • Use only grounded hoses. • If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem. • Keep a working fire extinguisher in the work area. WARNING

The typical installation shown in FIG. 1 is only a guide. It is not a complete system design. Contact your Graco distributor for assistance in designing a system to suit your needs. Mounting Bracket (FIG. 2) Mounting Bracket Kit 249440 is available for resting the dispense valve on a console. Drum Mount Bracket (FIG. 3) Mounting Bracket 15B750 is available for resting the dispense valve on a drum. NOTICE The dispense valve is not designed for in-line installation. Do not install with a shutoff valve on the outlet side of the meter. Such installation could result in damage to the meter housing cover. FIG. 1 ITEM DESCRIPTION A Electronic metered dispense valve B Fluid shut-off valve C Hose D Hose reel fluid inlet hose E Hose reel A Thermal Relief Kit (not shown) is required. The kit required will vary by pump selected. See Parts, page 40 for a list of available kits. B D E C A ti11010a FIG. 2 FIG. 3 ti11822 ti11823

This equipment will stay pressurized until the pressure has been manually relieved. To reduce the risk of serious injury from pressurized fluid, accidental spray from the dispense valve or splashing fluid, follow this Pressure Relief Procedure when ever you: • Are instructed to relieve pressure. • Check, clean or service any system equipment. • Install or clean fluid nozzles or filter. 1. Turn off power supply to the pump or close upstream ball valve. 2. Trigger the dispense valve into a waste container to relieve pressure. 3. Open any bleed-type master air valves and fluid drain valves in the system. 4. Leave the drain valve open until you are ready to pressurize the system. Grounding The equipment must be grounded. Grounding reduces the risk of static and electric shock by providing an escape wire for the electrical current due to static build up or in the event of a short circuit. Pump: Follow manufacturer’s recommendations. Air and fluid hoses: Only use electrically conductive hoses. Check electrical resistance of hoses. If total resistance to ground exceeds 29 megohms, replace hose immediately. Air compressor: Follow manufacturer’s recommendations. Fluid supply container: Follow local code. To maintain grounding continuity when flushing or relieving pressure: hold a metal part of the dispense valve firmly to the side of a grounded metal pail, then trigger the valve. Pre-Installation Procedure 1. Relieve pressure, page 7. 2. Close the shut-off valve (B, FIG. 1). 3. Ground the hose and reel or console, page 7. Leave at least two threads bare when using PTFE tape. The bare threads ensure a ground is maintained. Installation Procedure Flushing If this is an existing installation, go to Installing Meter section, page 8. The following procedure, Steps 1-5 are the Flushing Procedure. 1. Close the fluid shut-off valve (B, FIG. 1, page 6) at each dispense position. 2. Make sure: • main fluid outlet valve at the pump is closed, • air pressure to the pump motor is adjusted, and • air valve is open. FIRE HAZARD: Conductive metal surfaces on the meter must not make contact with any positively charged metal surface, including (but not limited to), the starter solenoid terminal, alternator terminal or battery terminal. Such contact could cause electrical arcing and a fire. NOTICE • If this is a new installation or if the fluid lines are contaminated, flush the lines before you install the metered valve. Contaminated lines could cause the valve to leak. • Never dispense compressed air with meter. Doing so will damage meter.

a. Place the hose end (with no dispense valve connected) into a container for waste oil. b. Secure the hose in the container so it will not come out during flushing. c. If you have multiple dispense positions, first flush the dispense position farthest from the pump and work your way toward the pump. 4. Slowly open the shut-off valve (B) at the dispense position. Flush out a sufficient amount of oil to ensure that the entire system is clean; then close the valve. 5. Repeat Step 4 at all other positions. Installing Meter (FIG. 4 ) 1. Relieve pressure, page 7. 2. Slide the swivel boot (32) back, over the hose, small end first, to access the swivel fitting (a). 3. Apply thread sealant to the male threads of the hose fitting. Thread the hose fitting into the meter swivel (31). Use two wrenches to tighten securely (FIG. 4). Installing Tube Extension (FIG. 5) 1. a. Loosen nut (a) until it is completely off tube threads. b. Thread extension (20) into housing (b) until it bottoms out. c. Align extension (20) with meter housing and handle (c). d. Firmly tighten nut (a). FIG. 4 Make sure you let the sealant cure to the manufac- turer’s recommendations before circulating fluid through the system. 31 ti10983a 32 a FIG. 5 NOTICE Do not use PTFE tape or thread sealant on threads of extension tube (20). This could cause the fitting to leak. 20 a c b ti10615A

1. a. Thread new nozzle (33) onto extension (20). b. With an open-end adjustable wrench on flats of nozzle bushing, tighten firmly. 2. Open automatic twist lock nozzle and all fluid shut-off valves. Start pump to pressurize system. See Operation Screens, Dispensing in either the Manual or Preset Mode instructions beginning on page 19 for complete meter operation information. 3. To ensure dispensing accuracy, purge all air from the fluid lines and dispense valve before you use it. 4. Set the system flow to the desired flow rate. FIG. 6 • Only tighten nozzle with wrench on flats of the nozzle bushing. • Do not disassemble the bushing from nozzle. Disassembly will affect performance of the nozzle. NOTICE Do not trigger meter when nozzle is closed. Fluid will build up behind the nozzle, leak from the nozzle, and unexpectedly be expelled when the nozzle is opened. If you do accidentally trigger the meter with the nozzle closed, point the nozzle into a waste bucket and open the nozzle to relieve pressure and expel the built up fluid. 20 33 ti10615A

5-Way Menu Navigation Button (FIG. 7) • Includes 4 direction ARROWS (UP, DOWN, LEFT, RIGHT) and a center, ENTER button. • Pressing the direction ARROWS allows user to easily scroll through menus. To select/store your selection, you must press the center, ENTER button. • Pressing and holding a direction ARROW down allows user to scroll through menus quickly. Meter Display Adjusting Screen Contrast using ARROWS On the Setup Home Screen (page 11), use the LEFT and RIGHT ARROWS to adjust the screen contrast. • Darken the Screen: Press the RIGHT ARROW multiple times. • Brighten the Screen: Press the LEFT ARROW multiple times. Asleep/Awake Mode • Asleep: Battery-saving mode. The display goes blank after 2 minutes of inactivity during normal operation. Unit continues to keep track of amount dispensed while the display is asleep. • Awake: Display comes awake from sleep mode when you press any ARROW or the ENTER button or when you squeeze the trigger to dispense fluid. Locking and Unlocking Trigger The Preset Meters only, include a locking trigger feature that allows the user to lock the trigger in the dispense position as shown in FIG. 8. To release the lock, firmly squeeze the trigger to the handle. Preset Meters Only FIG. 7 ti11824 5-Way Menu Navigation Button FIG. 8 Unlocked Locked

312865H 11 Setup Mode Screens If you are in Operation Mode you must be on the Home Screen shown in FIG. 10, to access the Setup Mode Screens. (A complete description of the Home Screen is provided on page 18). To display the Home Screen: 1. Wake up the meter by pressing any button on the key pad. 2. When an operation mode screen displays (such as the one shown in FIG. 9): a. Use the RIGHT ARROW to move the curser over the House icon (a). b. Press center, ENTER button to display the Home Screen (FIG. 10). FIG. 9 MOBIL1 5W-20 10.56 QTS a ti12179a FIG. 10 MOBIL1 5W-20 MANUAL PRESET TOTALS MOBIL1 5W-20 MANUAL TOTALS ti12184a ti12175a Manual Meters Preset Meters

12 312865H Main Setup Screen (FIG. 12) All Meters The Main Setup Screen is the first screen displayed when you enter the Setup Mode. This screen displays a list of the available Setup Screens and also includes a link back to the Home Screen. Manual Meters Screens: • UNITS/LIMIT • CALIBRATE • BANNER • LANGUAGE • HOME Preset Meters include all the Manual Meter’s Setup Screens and also a PRESET screen. • UNITS/LIMIT • CALIBRATE • PRESET • BANNER • LANGUAGE • HOME Displaying Setup Screen from an Operation Mode Screen 1. Hold down the RIGHT ARROW (a) only, for a few seconds (FIG. 11). 2. Then at the same time, also press the center, ENTER button (b) (FIG. 11). Hold both buttons down until the Main Setup Screen shown in FIG. 12 dis- plays. Main Screen Features (FIG. 12) A. Screen Identifier Icon: Wrench icon displays in the upper right corner when user is on the Main Screen of the Setup screens. B. Setup Screens: Screens available to user. 1. Use UP or DOWN ARROWS to select a screen from the list. 2. Press center, ENTER button to confirm selection. Selected screen displays. 1. Software Version Number: Reference number. You may be asked to provide this number when contacting Graco for technical support. FIG. 11 (a) (b) ti11824a FIG. 12 UNITS/LIMIT CALIBRATE PRESET BANNER LANGUAGE HOME 1.23.45 Manual Meters Preset Meters B A UNITS/LIMIT CALIBRATE BANNER LANGUAGE HOME 1.23.45 B A ti12177a ti12186a 1 1

312865H 13 Units/Limit Screen (FIG. 13) For All Meters Sets the units of measurement to pints, quarts, liters, or gallons. Units/Limit Screen Features (FIG. 13) All meters include C - E C. Units Mode: Displays measurement unit that was selected using the Set Measurement Units button (E). D. Wrench Icon: Returns user to Main Setup Screen. E. Set Measurement Units button/field: Sets unit of measurement as pint, quart, gallon or liter. To change/set the Unit of Measurement: 1. Use LEFT or RIGHT ARROW to move curser to the Set Measurement field (E). 2. Use UP or DOWN ARROWS to display measure- ment unit choices: PTS, QTS, L, GAL. 3. Press center, ENTER button to confirm selection. Selected measurement unit is displayed on screen (C). 4. When you are finished making changes, use the RIGHT ARROW to move curser over Wrench icon. 5. Press center, ENTER button to return to Main Setup Screen. Preset meters also include F - G F. Set Manual Dispense Limit field: Sets maximum quantity of fluid that can be dispensed in Manual Mode. To change/set the Manual Dispense Limit: 1. Use RIGHT ARROW to move curser to Manual Dis- pense Limit field (F). 2. Use UP or DOWN ARROWS to increase and decrease displayed amount. 3. When amount you want to use is shown in field, press center, ENTER button to confirm amount. Confirmed amount displays on screen (G). 4. When you have finished making changes, use the RIGHT ARROW button to move curser over Wrench icon. 5. Press center, ENTER button to return to Main Setup Screen. G. Manual Limit Confirmation: Displays maximum quantity of fluid that can be manually dispensed at one time. Amount is assigned on the task bar Set Manual Dispense Limit field (F). Preset dispense amounts are not affected by the manual dispense limit you set. FIG. 13 QTS UNITS = QTS MANUAL LIMIT = 5.0 5.0 D C G E F Preset Meters Manual Meters ti12191a QTS UNITS = QTS C D E

14 312865H Calibrate Screen (FIG. 14) For All Meters Recalibrates the meter for different fluids. Table 1. Calibration Factors • Calibration factors at 70°F (21°C) at 2.0 gpm (7.6 lpm). • Calibration number may vary slightly due to temperature or flow rate. All meters include D - M D. Wrench Icon: Returns user to Main Screen. J. Calibration Factor: Displays amount operator dispensed during meter calibration. K. Preset Calibration Factor: Preset calibration amount displays. Adjusting the Preset Calibration Factor: 1. Use your LEFT or RIGHT ARROW to move the curser to the Calibration Factor Field (K) . 2. Use the UP or DOWN ARROW to manually adjust the Preset Calibration Factor up or down (this can only be done on Calibrate Screen 1 (FIG. 14). 3. Press center, ENTER button to confirm new setting. New setting displays in Calibration Factor field (J). L. Start/End button: Clicked at the start and completion of calibration. See Recalibrating the Meter (page 15). M. Dispense: Only appears on Screen 2 (FIG. 14). Displays amount operator dispensed during calibration test. Fluids Calibration Number Quarts Liters Oil (10W - 30) 173 183 Gear Lube 173 183 Automatic Transmission Fluid 167 176 Antifreeze 159 168 FIG. 14 D J M K L L Calibrate Screen 1 Calibrate Screen 2 ti12173a ti12174a

312865H 15 Recalibrating the Meter (FIG. 14) The meter is shipped from the factory with the default calibration factor for 10W30 motor oil - at 70°F (21°C). This calibration factor is sufficiently accurate for most oils. If other fluids are used or if greater accuracy is required, the meter can be recalibrated by performing one of the following recalibration methods. 1. Choosing a Calibration Factor From the Calibration Table 1 1. Use LEFT or RIGHT ARROW to move the curser to the Calibration Factor Field (K) . 2. Use the UP or DOWN ARROWS to manually adjust the Preset Calibration Factor up or down until the number displayed matches the calibration factor you have chosen from Table 1. 3. Press center, ENTER button to confirm new setting. New setting displays in Calibration Factor field (J). 4. Use the RIGHT ARROW button to move curser over Wrench icon. 5. Press center, ENTER button, to return to Main Setup Screen. OR 2. Manual Calibration Procedure See FIG. 14, page 14 for the Calibrate Screens 1 and 2 referenced in the following instructions. • When an English unit (gallon, quarts, pints) is set as the measurement unit on the Units/Limit Screen, page 13, use a one quart graduated cylinder to calibrate the meter. • When a System International Unit (SI) (Liter) is set as the measurement unit on the Units/Limit Screen, use a one Liter graduated cylinder to calibrate the meter. 1. Use the LEFT or RIGHT ARROWS to select START (L) on Calibrate Screen 1. 2. Press the center, ENTER button to confirm selec- tion. Calibrate Screen 2 will appear. 3. Dispense exactly 1 quart (or 1 liter) of fluid into a calibrated 1 quart (or 1 liter) container. The Calibration Factor will appear on the screen in the Calibration Factor field (J). 4. Use the LEFT or RIGHT ARROWS to select END (L) on Calibrate Screen 2. 5. Press the center, ENTER button to confirm selec- tion. Calibrate Screen 1 will appear. 6. When you have finished making changes, use the RIGHT ARROW button to move curser over Wrench icon. 7. Press center, ENTER button, to return to Main Setup Screen. To attain the most accurate calibration: • Use the manual calibration procedure (Method 2). • Use a certified, graduated cylinder; either 1-Quart or 1-Liter volume in the system of Units to be used (either English or SI) for real-time dispenses. • Calibrate using the exact fluid to be dispensed, at the temperature expected during dispense. • After calibration check your results by measuring a dispense. • Be sure to remove all fluid from graduated cylinder between calibration attempts. • Be sure meter is set to proper system of units for container you are using. Calibration factors provided in Table 1 (page 14), are only approximate, but sufficient for most appi- cations. For the most accuracy, use method 2, Manual Calibration Procedure. Once the meter has been calibrated, the unit of measure can be changed to any other unit, without the need for recalibration.

16 312865H Preset Screen (FIG. 15) For Preset Meters Only Sets the default preset amounts. Typically, you would enter amounts you most frequently dispense. Preset Meters include D, P and Q D. Wrench Icon: Returns user to Main Screen. P. Measurement Unit: Set on Units/Limit Screen, page 13. Q. Set Preset Amounts: Sets dispensing options for the Preset Dispense mode. Sets up to 3, default preset quantities. The amounts can be listed in any order and do not have to be in a numeric order. To set Preset amounts (FIG. 15): 1. Use the LEFT or RIGHT ARROWS to select one of the three amount fields (Q). 2. Use the UP or DOWN ARROWS to increase or decrease the number appearing in the field until the desired amount displays. Pressing and holding the ARROW button down, increases the scrolling speed. 3. Press center, ENTER button to confirm amount. 4. When you have finished making changes, use the LEFT OR RIGHT ARROW button to move curser over Wrench icon. 5. Press center, ENTER button, to return to Main Setup Screen. FIG. 15 PRESET 4.0 6.0 10 1 2 3 QTS D Q P ti12188a The amounts displayed do not automatically recal- culate quantities when changing between measure- ment units. For example, if you change from quarts to liters you must manually change the preset amounts.

312865H 17 Banner Screen (FIG. 16) For All Meters Creates the information banner displayed across top of the Home, Manual and Preset Screens. Banner Screen Features D and R D. Wrench Icon: Returns user to Main Screen. R. Banner field: Information line. Provides space for up to 11 numeric and alpha characters and/or spaces. Using the DOWN ARROW button when a field is blank will also provide the following characters for selection: (period) “ . “; (forward slash) “ / “; or (dash) “ - ”. To create a banner: 1. Use the UP or DOWN ARROWS to scroll through numerals, then alpha characters and then blank/spaces. 2. Press center, ENTER button to select characters. When character is selected, curser automatically moves to the next character field. Use the RIGHT ARROW button to skip fields or if you do not need to use all 11 spaces, to return curser to the Wrench icon. After 11th character has been confirmed, curser automatically moves to Wrench icon (D). 3. Use the center, ENTER button, to return to the Main Setup Screen. Language Screen (FIG. 17) For All Meters Sets language preference for text displayed on meter. Choices include English and Spanish. Language Screen Features D, S, and T D. Wrench Icon: Returns user to Main Screen. S. Language field: Identifies selected language. T. Language field/button: When curser is over this button, each time UP or DOWN arrow is pressed, the name of the Language displayed on the button changes. To select your language: 1. Use the LEFT or RIGHT ARROW to move the curser to the Language field/button (T). 2. Use UP or DOWN ARROWS to view language choices. 3. When the name of your language is displayed on the field/button (T), press the center ENTER button to confirm selection. The selected language is then displayed on screen in Language field (S). 4. When you have finished making changes, use the LEFT OR RIGHT ARROW button to move curser over Wrench icon. 5. Press center, ENTER button, to return to Main Setup Screen. FIG. 16 M O B I L 1 5 W - 2 0 D R ti12181a FIG. 17 After you press the center, ENTER button, the name on the field/button will also change from “SPANISH” to “EPANOL” and will appear this way on both the Language button (T) and in the Language field (S) on the screen. ENGLISH LANGUAGE = ENGLISH D S T

18 312865H Dispensing Fluid and Operation Mode Screens If you are in the Setup Mode, to display the Operation Mode Screens use the UP or DOWN ARROW button to select HOME from the list. Press the Center ENTER button to display the Operation Mode Home Screen shown in FIG. 18. A complete description of the Setup Mode Screens begins on page 11. Home Screen (FIG. 18) All Meters All Meters include Include A - D A. Screen Identifier Icon: House displays when user is on the Home Screen. B. Operation Screens: List/menu of screen choices available to user. Operation Screen choices include: Manual Meters • MANUAL • TOTALS Preset Meters • MANUAL • PRESET • TOTALS 1. Use UP or DOWN ARROWS to scroll through options. 2. Press center, ENTER button to confirm selection and display the screen. C. Battery Indicator: Appears only on Home Screen. Shows current battery charge strength. Appears and flashes on all screens when battery’s charge is low. D. Information Banner: Configurable information banner. Data is input on Setup Mode Banner Screen, page 17. FIRE HAZARD: Conductive metal surfaces on the meter must not make contact with any positively charged metal surface, including (but not limited to), the starter solenoid terminal, alternator terminal or battery terminal. Such contact could cause electrical arcing and a fire. FIG. 18 MOBIL1 5W-20 MANUAL PRESET TOTALS C A D B Preset Meters Manual Meters MOBIL1 5W-20 MANUAL TOTALS B D A C ti12175a ti12184a

312865H 19 Manual Dispense (FIG. 19) All Meters See FIG. 19 for terms D - H D. Information Banner: Configurable information banner. Data is input on Setup Mode Banner Screen, page 17. E. Unit of Measurement: Identifies unit of measurement, pint, quart, gallon or liter. Measurement Unit is set on Setup Mode Units/Limits Screen, page 13. F. Home Icon: Returns user to Home Screen. G. Reset: Resets counter (H) to zero. H. Counter: Before dispense has begun, display reads 0.00. As fluid is dispensed, counts up from zero. To reset counter to zero after a dispense: 1. Use the LEFT or RIGHT ARROW button to move curser to RESET (G). 2. Press center ENTER button. The displayed amount in field H returns to zero. To dispense in Manual Mode: If display was asleep, press any button to wake it up. 1. From HOME screen, use the UP or DOWN ARROWS to select MANUAL (FIG. 20). 2. Press center, ENTER button to confirm selec- tion.The Manual Dispense screen (FIG. 21) appears. 3. Squeeze trigger to dispense fluid. If using a Preset meter, trigger may be locked during the dispense. Fluid flows. The amount displayed counts up from zero or from the previously dispensed amount (FIG. 21) and displays in field H. 4. Release, or for Preset meters only, unlock trigger when you have dispensed the desired amount of fluid. Fluid flow stops. Amount dispensed displays in field H. 5. Use LEFT or RIGHT ARROW to move curser to RESET button (G). Press center ENTER button to reset the displayed amount in field H to zero. FIG. 19 MOBIL1 5W-20 10.56 QTS E F G H D ti12178a FIG. 20 FIG. 21 MOBIL1 5W-20 MANUAL PRESET TOTALS ti12180a Preset shown MOBIL1 5W-20 10.56 QTS G H ti12178a

20 312865H Preset Dispense (FIG. 22) Preset Meters Only See FIG. 22 for terms D - L D. Information Banner: Configurable information banner. Data is input in Setup Mode, Banner Screen, page 17. E. Unit of Measurement: Identifies unit of measurement, pint, quart, gallon or liter. Unit is selected in Setup Mode, Units/Limit Screen, page 13. F. Home Icon: Returns user to Home Screen. G. Reset: Resets counter (H) to zero. H. Counter: Before dispense has begun, display reads 0.00. As fluid is dispensed, counts up from zero. At the same time the Progression Bar (J) displays a real-time, visual representation of the progress made toward completing the dispense. J. Progression Bar: Displays a real-time, visual representation of the progress made toward completing the dispense. Runs in conjunction with Counter (H). For example, in FIG. 22, a partial dispense of 2.5 quarts of the total Preset Dispense of 5.0 quarts is shown. The Progression Bar shows that approximately half the dispense is complete. L. Preset Quantities: Use the UP or DOWN ARROW to select field L on the task bar. a. Use the UP or DOWN ARROWS to scroll through the 3 available Preset Quantities (L). Each time you press the UP or DOWN ARROWS, one of the 3 preset amounts dis- plays on the task bar in field L. b. When the Preset Quantity you want to dispense is shown in field L, press the center, ENTER button to select it. FIG. 22 MOBIL1 5W-20 2.50 QTS 4.0 XXXXXXXXXXXXXXXX E F G H D J L ti122410a If a suitable preset quantity is not available, select an amount that is closest to the amount you want to dispense. Amounts can be modified following the procedure described on page 21.

312865H 21 To modify the amount selected: a. Use the UP or DOWN ARROW to scroll up or down to increase or decrease the amount shown in field L. Each time you press the UP or DOWN ARROW the amount will increase or decrease in increments of 0.1 units. To speed up the scrolling progression, press and hold the UP or DOWN ARROW. b. IMPORTANT!!! When the new dispense amount is shown in field L, the number flashes, indicating a change has been made that requires confirmation. To confirm new amount you MUST PRESS the center, ENTER button on the key pad within 15 seconds. If you begin a dispense without confirming the new amount, the Preset Amount will return to the previous confirmed amount shown in field L. For example, in FIG. 23 (below) the original, confirmed Preset Dispense amount (A) was 4.0 qts. The amount was increased to 8.0 quarts and because it has not been confirmed, is flashing on the screen (B). After the user confirmed this change by pressing the center ENTER button on the key pad, the new dispense amount no longer flashes and is now set to dispense 8.0 quarts (C). To permanently modify the default Preset Quantities, see To set Preset amounts: on page 16. FIG. 23 MOBIL1 5W-20 2.50 QTS 4.0 XXXXXXXXXXXXXXXX 8.0 8.0 A B C

22 312865H To dispense in Preset Mode: If the display was asleep, press any button to wake up the display. 1. From HOME screen, use the UP or DOWN ARROWS to select PRESET (FIG. 24). 2. Press center, ENTER button to confirm selec- tion.The Preset Dispense screen (FIG. 25) appears. 3. Squeeze trigger to begin dispensing fluid. The trig- ger may be locked during the dispense. Fluid flows. The amount displayed counts up from zero or from the previously dispensed amount (FIG. 25) and displays in field H. A visual representation of the dispense progression also appears on the progression bar (J). When the preset amount has been dispensed, fluid flow stops automatically. The total dispensed amount appears in field H. If you want to stop fluid flow before the preset amount is dispensed, release or unlock trigger. To continue dispensing fluid, squeeze and/or lock trigger again. Dispensed amount shown in field H and on progression bar (J) continues to count up toward preset amount. If you want to continue dispensing fluid after preset amount has been dispensed, squeeze trigger. The meter continues dispensing fluid in Manual Mode until you release trigger. 4. Use LEFT or RIGHT ARROW to move curser to RESET button (G). 5. Press center ENTER button to reset the displayed amount in field H to zero and clear the progression bar (J). FIG. 24 FIG. 25 MOBIL1 5W-20 MANUAL PRESET TOTALS ti12242a MOBIL1 5W-20 2.50 QTS 4.0 XXXXXXXXXXXXXXXX G H ti12410a J

312865H 23 Totals Screen (FIG. 26) All Meters See FIG. 26 for terms F, G, M - P F. Home Icon: Returns user to Home Screen. G. Reset: Resets counter (M) to zero. M. Resettable Total: Shows cumulative amount that has been dispensed in all modes. Can be reset to zero at any time with Reset button (G). N. Total: Shows cumulative amount that has been dispensed in all modes for the life of the unit. Cannot be reset. When the Total (N) reaches 999,999 the count resets automatically to 000. To display Totals Screen: If the display was asleep, press any button to wake up the display. 1. From HOME screen, use the UP or DOWN ARROWS to select TOTALS (FIG. 27). 2. Press center, ENTER button to confirm selec- tion.The Totals screen (FIG. 26) appears. 3. To reset Resettable Total field (M) to zero, use LEFT or RIGHT ARROW to move curser over RESET but- ton (G). 4. Press center ENTER button to reset the displayed amount in field M to zero. FIG. 26 3485 14953 QTS GAL F G M N ti12190a FIG. 27 MOBIL1 5W-20 MANUAL PRESET TOTALS ti12243a

operating properly. • When calling for Technical Assistance you may be asked to provide the Software Version that is being used by your meter. Refer to FIG. 10, page 11, item #1 for help determining where this information is shown on your meter. Problem Cause Solution Battery icon is blinking. Batteries are low. Replace batteries, page 27. Display does not activate. Batteries are defective. Replace batteries, page 27. Electronic control is malfunctioning. Replace the electronic bezel assem- bly. (See Manual Meters Parts page 34 or Preset Meters Parts page 36 to identify which kit is required for your meter). Cannot read display Contrast is set too high or too low to be viewed in work area Adjust contrast. See Adjusting Screen Contrast Using LEFT or RIGHT ARROWS, page 10. Slow or no fluid flow. Filter is clogged. 1. Relieve pressure, page 7. 2. Clean or replace filter. Order Fil- ter Kit 255885. 3. If the problem remains, contact your Graco distributor for repair or replacement. Pump pressure is low. Increase pump pressure. Twist lock nozzle not fully open. Aim nozzle into bucket or rag. Fully open nozzle. Do not trigger meter when nozzle is closed! If you do accidentally trig- ger the meter with the nozzle closed, point nozzle into a waste bucket and open the nozzle to relieve pressure and expel built up fluid. Shut-off valve is not fully open. Fully open shut-off valve. Foreign material is jammed in the meter housing. Contact your Graco distributor for repair or replacement. Displayed dispensed amount is not accurate. Unit needs to be calibrated for the fluid that is being dispensed. Calibrate the meter for the fluid that is being dispensed. See Calibrate Screen, page 14. Meter leaks from cover/control. Poor seal at metering cover chamber. Contact your Graco distributor for repair or replacement.

reset sufficiently to dispense fluid. Excessive dirt buildup is causing trip rod to stick. Clean trip rod or replace (page 28). Order Kit 255889. Meter leaks from twist lock nozzle. • It is important to distinguish between the two causes of this problem. A new nozzle will NOT correct a fluid leak caused by a faulty valve. Twist lock nozzle has a damaged seal. Replace nozzle. See Step 1 in Instal- lation Procedure, page 9. Valve has damaged or obstructed seals. Clean valve stem and o-rings or replace. Order Kit 255888. Meter leaks from swivel. Poor swivel/hose connection. Apply PTFE tape (leave a minimum 2 engaged threads uncovered for elec- trical continuity) or sealant to threads of hose and tighten the connection. See Step 3 in Installation Procedure, page 8. Poor swivel/meter housing connec- tion. Torque the fitting to 20-25 ft.-lbs. Swivel seals have deteriorated and leak. Replace swivel. Unit does not stop dispensing when assumed preset amount is dis- pensed. Valve is dirty. Clean valve. Low battery. Replace batteries, page 27. Solenoid not functioning (Preset only). Replace solenoid. Problem Cause Solution

code displayed you can: • Select Manual option on Home Screen. Error code is cleared. Unit switches to Manual mode and dispensed amount is displayed. • Select reset option. Error code is cleared, Unit switches to Auto mode and the present amount is displayed. Error Code Cause Solution Err 1 Battery voltage is low Change battery, page 27. Err 2 Switch Error: Error occurred with pick-up in internal gear. or Ensure that your flow rate is not higher than 14 gpm (37.8 lpm). For further assistance, contact your Graco distributor. Unit was dropped or unit encountered excessive vibration during shipping. Select Reset, item G, page 19. Err 4 Flow has continued after it should have shut off. or Check for low battery symbol and replace batteries if indicated, page 27. For further assistance, contact your Graco distributor. Flow has occurred in lockout condi- tion. Navigate to Home screen. Then re-enter Dispense Screen. Err 5 In Manual Mode only. The unit has dispensed the shut-off default amount and has stopped fluid flow. Select Reset, item G, page 19 and dispense again.To change the shut-off default amount, see Units/Limits Screen, page 13. Err 6 A present dispense amount of zero was entered for the dispense or is stored as the default and a Preset dispense was attempted. Enter an amount that is not zero. See Preset Dispense Screen, page 20. Err7 Battery voltage is too low. or Change battery, page 27. CAP ERROR: Error has occurred in control. Replace the electronic bezel assem- bly. (See Manual Meters Parts page 34 or Preset Meters Parts page 36 to identify which kit is required for your meter).

Replacing the Battery The low battery and dead battery displays are explained in the Troubleshooting Table, page 24. To change the battery: 1. Press firmly on battery compartment cover. Using a flat screwdriver turn latch screw counter-clockwise 1/2 turn. 2. Remove the battery compartment cover and batter- ies. 3. Install new batteries. See FIG. 28 for battery orienta- tion. 4. Replace cover. The cover is designed to only fit on battery compartment one way. The notch (a) on cover fits into slot (b) on compartment. (FIG. 29). . 5. Press down firmly on cover. Using a flat screwdriver turn latch screw clockwise 1/2 turn. • Only use the size and type of batteries specified in this manual. Batteries required to meet life expectancy: • Energizer E91 • Be sure to follow the correct polarity when installing batteries in the battery compartment (FIG. 28). Reversed batteries may damage this meter. • Do not mix different types of batteries together or old batteries with fresh ones. Always replace all 4 batteries with 4, fresh, new batteries. FIG. 28 FIG. 29 ti10984a 47 (b) (a)

(SDP5 & SDP15 Meters Only) Disassembly 1. Relieve Pressure, page 7. 2. Use a Torx (T20) wrench to remove 4 corner screws (A) located on the bottom of the meter (FIG. 30). Keep these screws for reassembly. 3. Turn meter over and tilt cover back (FIG. 31). 4. With your finger, carefully lift up clip (D) to discon- nect battery lead (B) from battery module. 5. Unsnap solenoid lead (C) (FIG. 33). FIG. 30 You will not be able to completely remove the cover until you disconnect the leads to the battery, sole- noid and remove the reed switch PCB. FIG. 31 A A ti11936a ti11937a B C FIG. 32 NOTICE Do not use a screw driver or any other tool to lift up clip (D) when disconnecting battery lead (B) from bat- tery module. If the clip is damaged or broken it cannot be repaired; you will have to replace the battery mod- ule. Order Part No. 255197. FIG. 33 B ti11938a D D ti11939a C

to the cover plate (FIG. 34). Keep these screws for reassembly. Remove cover assembly. 7. Remove and discard o-ring (5) (FIG. 35). 8. Remove guard (9) by inserting your thumb or finger behind the cover and pry it loose. Then slide guard down and out of groove on housing (FIG. 36). 9. Unscrew solenoid (12) and remove from meter housing (FIG. 37). If necessary, a pliers can be used to loosen solenoid. FIG. 34 FIG. 35 ti11940a D 5 ti11941a FIG. 36 FIG. 37 9 ti12009a 12 ti12238a

trip rod from your kit (2) or a non-metal rod or dowel to push trip rod through meter housing (FIG. 38 and FIG. 39) far enough to access pin (19) holding together trip rod and trigger. 11. Use a pick to push pin (19) out (FIG. 39). 12. Remove trigger assembly (6) from meter housing. 13. Remove trip rod assembly from meter housing. Cleaning Trip Rod a. If the trigger does not reset sufficiently to dis- pense fluid, clean trip rod and spring with a soft brush and cleaning fluid such as mineral spirits. b. Inspect trip rod and spring. If damaged, replace using Trip Rod Replacement Kit 255889. FIG. 38 FIG. 39 FIG. 40 ti12011a 19 19 ti12012a ti12016a 6 Be careful when you remove the trip rod assembly. Cover the balls with your fingers or a rag to prevent them from falling out. FIG. 41 ti12013a 6

the old parts. 1. Insert balls (3) in trip rod (2) (FIG. 42). 2. Slide spring (1) over trip rod (2) (FIG. 42). 3. Insert trip rod assembly in opening in meter housing (FIG. 43). 4. Turn meter over and place in vise. Align holes in trig- ger assembly with holes in trip rod (2). Use the old trip rod or a non-metal rod or dowel to push trip rod up and out of the meter housing (FIG. 44) far enough to see hole for pin (19) to slide into, however, do not install pin in this step. 5. Install trigger assembly (8) (FIG. 44). Push pin (19) through holes in trigger and trip rod assembly. 6. Install solenoid (12). Finger tighten securely. 7. Install o-ring (5). FIG. 42 FIG. 43 ti12014a 3 2 1 FIG. 44 FIG. 45 FIG. 46 ti12015a 19 2 8 ti12238a 12 ti11941a 5

screws (D) to secure reed switch PCB to cover plate. Tighten screws until they bottom out. 9. Reconnect lead (B) to battery by carefully sliding connector over battery terminals (E) until it snaps securely into place under clip (D) (FIG. 48). 10. Reconnect solenoid lead (C) (FIG. 49). 11. Position cover over meter housing. FIG. 47 FIG. 48 ti11940a D ti11938ab E D NOTICE Do not use a screw driver or any other tool to lift up clip (D) when reconnecting battery lead (B). If the clip is damaged or broken it cannot be repaired; you will have to replace the battery module. Order Part No. 255197. FIG. 49 NOTICE When replacing cover, be careful not to pinch wires. D ti11939a C

pounds. 13. Install guard (9). FIG. 50 FIG. 51 A A ti11936a ti12009a 9

34 312865H SDM5 & SDM15 Manual Meters Parts ( ▲ Replacement Danger and Warning labels, tags and cards are available at no cost. Ref Part Description Qty 2 115477 SCREW, mach, torx pan hd 6 5 120812 O-RING, seal 1 6 15K418 TRIGGER, meter 1 9 15K464 GUARD, bumper 1 11 HOUSING, meter 1 17 255197 MODULE, battery 1 18 256493 KIT, repair, electronic bezel, includes 18a and instruction man- ual 312942 18a LABEL, control, overlay 1 19 120850 PIN, dowel M4 2 24 255888 KIT, repair, seals and spring only includes 24a-24d and instruction manual 312939 16F811 KIT, repair, valve, spring and seals includes 24a-24f and instruction manual 312939 24a PACKING, o-ring 1 24b PACKING, o-ring 1 24c O-RING, 3 24d SPRING, compression 6.1 x 76mm 1 24e CARTRIDGE, valve 1 24f STEM, valve 1 28 120853 PIN, dowel 1 31 247344 SWIVEL, straight, 1/2-14 NPT, includes 31a (used with 255348, 255349, 255350, 255802, 255803, 255804, 256836, 256837) 1 247345 SWIVEL, straight, 3/4-14 NPT includes 31a (used with 255800, 255801) 1 31a 105765 O-RING 1 32 15T366 BOOT, swivel, 3/4” hose, black (standard with meter) 1 15T367 BOOT, swivel, 3/4” hose, red 1 15T368 BOOT, swivel, 3/4” hose, blue 1 15T369 BOOT, swivel, 3/4” hose, green 1 15T370 BOOT, swivel, 3/4” hose, yellow 1 34 255885 KIT, filter, includes 34a-34c 34a FILTER, wire, 40 mesh 10 34b PACKING, o-ring 10 34c SPACER, strainer 10 39 15R057 BUSHING, stationary, rod 1 40 15R056 ROD, stationary 1 41 115999 RING, retaining 1 47 121413 BATTERY, pkg, 4 count, alkaline, AA (page 27) 1 49▲ 15T259 LABEL, CE 1 50 15T492 SPACER, 1/4 OD x 0.9 th 4 51 15T603 GUARD, right 1 52 15T604 GUARD, left 1 53 117436 SCREW, thd forming 2 Ref Part Description Qty

312865H 35 34a 34b 34c 24b 24a 24e 24f 24c 24d 19 40 41 52 51 53 34 ti11916b 11 39 28 5 50 24c 49 18 9 32 31 31a 2 Torque to 25-35 IN. LBS 3 5 3 5 Torque to 20-30 FT. LBS 5 18a 17 / 47 6

36 312865H SDP5 & SDP 15 Preset Meters Parts ( ▲Replacement Danger and Warning labels, tags and cards are available at no cost. Ref Part Description Qty 2 115477 SCREW, mach, torx pan hd 6 3 255889 KIt, repair, trip rod, includes 3a-3c and instruction manual 312944 1 3a BALL,5 MM, carbide 3 3b ROD 1 3c SPRING, compression 10.67 mm 1 5 120812 O-RING, seal 1 6 15K418 TRIGGER, meter 1 7 15K443 ARM, trip 1 8 15K446 PLATE, ratchet 1 9 15K464 GUARD, bumper 1 11 HOUSING, meter 1 12 15W093 SOLENOID 1 15 15K602 SPRING, torsion 1 17 255197 MODULE, battery 1 18 256494 KIT, repair, electronic bezel, includes 18a and instruction man- ual 312942 1 18a LABEL, control, overlay 1 19 120850 PIN, dowel M4 2 24 255888 KIT, repair, seals ands spring only, includes 24a-24d and instruction manual 312939 16F811 KIT, repair, valve and seal, includes 24a-24f and instruction manual 312939 24a PACKING, o-ring 1 24b PACKING, o-ring 1 24c PACKING, o-ring 3 24d SPRING, compression 6.1 x 76mm 1 24e CARTRIDGE, valve 1 24f STEM, valve 1 28 120853 PIN, dowel 1 31 247344 SWIVEL, straight, 1/2-14 NPT, includes 31a (used with 255200, 255351, 255352, 255355, 255356, 256838, 256839) 1 247345 SWIVEL, straight, 3/4-14 NPT includes 31a (used with 255353, 255354) 1 31a 105765 O-RING 1 32 15T366 BOOT, swivel, 3/4” hose, black (standard with meter) 1 15T367 BOOT, swivel, 3/4” hose, red 1 15T368 BOOT, swivel, 3/4” hose, blue 1 15T369 BOOT, swivel, 3/4” hose, green 1 15T370 BOOT, swivel, 3/4” hose, yellow 1 34 255885 KIT, filter, includes 34a-34c 1 34a KIT, filter, wire, 40 mesh 10 34b PACKING, o-ring 10 34c SPACER, strainer 10 47 121413 BATTERY, pkg, 4 count, alkaline, AA (page 27) 1 49▲ 15T259 LABEL, CE 1 51 15T603 GUARD, right 1 52 15T604 GUARD, left 1 53 117436 SCREW, thd forming 2 Ref Part Description Qty

312865H 37 34a 34b 34c 24c 24b 24e 24f 24c 7 24d 15 6 19 8 3 18 24a 52 51 53 2 34 3a 3b 3c ti10617a 11 28 49 5 9 18a 12 17 / 47 32 31 31a Torque to 25-35 IN. LBS 3 Torque to 20-30 FT. LBS 5 5 3 5

38 312865H Nozzle (33) and Extension (20) Kits Part No. Description Fluid Type 255852* Automatic, non-drip quick close nozzle with rigid extension. Oil 255853* Automatic, non-drip quick close nozzle with flexible extension Oil 255854 Non-drip, quick close nozzle with rigid extension Gear Lube 255855* Non-drip, quick close nozzle with rigid exten- sion Anti-freeze 255856* Non-drip, quick close nozzle with flexible extension Anti-freeze *Used for dispensing 5gpm (22.7 lpm) or less. continued on page 32 ti11826 ti11827 ti11825 ti11827 ti11831 ti11830 ti11826 ti11828 ti11825 ti11828

312865H 39 255857 Non-drip, quick close, high-flow nozzle with rigid extension Oil and Anti-freeze 255858 Non-drip, quick close, high flow nozzle with flexible extension Oil and Anti-freeze Part No. Description Fluid Type ti11826 ti11829 ti11825 ti11829

40 312865H Nozzle (33) Kits Thermal Relief Kits (page 6) 255459* Automatic, non-drip, quick-close nozzle Qty Oil • BODY, nozzle 1 • O-RING, packing 1 • SPRING, compression 1 • O-RING, packing 1 • STEM, nozzle, valve 1 • SEAT, valve 1 255460* Automatic, non-drip, quick-close nozzle Anti-freeze • BODY, nozzle 1 • SPRING, compression 1 • O-RING, packing 1 • STEM, nozzle, valve 1 • O-RING, packing 1 • SEAT, valve 1 255461 Automatic, non-drip, high-flow nozzle Oil and Antifreeze • STEM, nozzle 1 • BODY, nozzle 1 • O-RING, packing 1 • O-RING, packing 1 • O-RING, packing 1 255470 Non-drip, quick-close nozzle Gear Lube • Housing 1 • Body, nozzle 1 • O-RING, packing 1 • O-RING, packing 1 • Plug, Hollow, hex 1 *Used for dispensing 5gpm (22.7 lpm) or less. Part No. Description PSI (bar) Rating 112353 Diaphragm pump for fuel dispense, valve only 50 psi (.34 MPa, 3.4 bar) 235998 Mini Fire-Ball™ 225, 3:1 600 psi (4.1 MPa, 41 bar) 237601 Fire-Ball 425, 3:1 600 psi (4.1 MPa, 41 bar) 237893 Fire-Ball 300, 5:1 900 psi (6.2 MPa, 62 bar) 248296 Fire-Ball 300, 5:1 (same as 237893 without bung adapter and swivel. Includes 6-foot hose) 900 psi (6.2 MPa, 62 bar) 238899 Diaphragm pump 150 psi (1 MPa, 10.4 bar) 240429 Fire-Ball 425, 6:1 and 10:1 1600 psi (11 MPa, 110 bar) 248324 Fire-Ball 425, 6:1 and 10:1 (same as 240429 minus bung adapter and swivel. Includes 6-foot hose) 1600 psi (11 MPa, 110 bar)

**Battery required to meet life expectancy: Energizer® Alkaline E91. † At 2.5 gpm (9.5 lpm), at 70°F (21°C), with 10-weight oil and 1 gallon dispensed. May require calibration; out-of-box accuracy is +/- 1.25 percent. Flow range* 0.26 to 14 gpm (1 to 53 lpm) Maximum Working Pressure 1500 psi (10 MPa, 103.4 bar) Maximum Working Pressure (50:50 antifreeze/water mix) 900 psi (6.2 MPa, 62 bar) Units of Measure pints, quarts, gallons, liters (factory set to quarts) Weight 5 pounds (2.26 kg) Dimensions (without extension) Length 13 inches (33 cm) Width 3.75 inches (9.5 cm) Height 5.75 inches (14.6 cm) Units of measure factory set in quarts maximum totalizer amount = 999,999 gallons or liters maximum recorded dispensed volume = 999.99 units maximum preset volume (Preset only) = 999.9 units Inlet 1/2-14 npt or 3/4-14 npt Outlet 3/4-16 straight thread o-ring boss Operating temperature range 4 °F to 158°F (-4°C to 70°C) Storage temperature range -40°F to 150°F (-40°C to 70°C) Battery** 4AA alkaline or lithium batteries Expected battery life in typical shop environment 1 year Wetted parts aluminum, stainless steel, PBT/PC, zinc, nitrile rubber, CS Fluid compatibility antifreeze, gear oil, crankcase oil, ATF Meter pressure loss 80 psi @ 10 gpm Accuracy† +/- 0.5 percent

Graco reserves the right to make changes at any time without notice. Original instructions. This manual contains English. MM 312865 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441 Copyright 2008, Graco Inc. is registered to ISO 9001 www.graco.com Revised 07/2010 Graco Extended Metered Dispense Valve Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. Graco will, for a period of five (5) years from the date of sale, repair or replace any non-electronic part of the equipment determined by Graco to be defective. Graco will also for a period of three (3) years from the date of sale, repair, or replace any meter electronic components determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties. In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit www.graco.com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590