Sony DCR-HC23E Service Manual

LEVEL 2 Link SERVICE NOTE MODEL INFORMATION TABLE SPECIFICATIONS FRAME SCHEMATIC DIAGRAMS BLOCK DIAGRAMS DISASSEMBLY PRINTED WIRING BOARDS REPAIR PARTS LIST SCHEMATIC DIAGRAMS Link Revision History Revision History How to use Acrobat Reader How to use Acrobat Reader DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 Ver 1.1 2006.02 DIGITAL VIDEO CAMERA RECORDER 2006B0500-1 © 2006.2 Published by DI Technical Support Department 9-876-927-31 US Model Canadian Model AEP Model UK Model East European Model North European Model E Model Argentine Model Australian Model Brazilian model Chinese Model Hong Kong Model Korea Model Photo: DCR-HC35E DCR-HC23E/HC24E/HC26/HC26E/HC35E RMT-830 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part num- ber specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. • Precaution on Replacing the VC-416 Board N MECHANISM (MDX-N110)

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 SPECIFICATIONS These specifications are extracted from instruction manual ofDCR-HC23E/HC24E/HC26E/HC35E. System Video recording system 2 rotary heads, Helical scanning system Audio recording system Rotary heads, PCM system Quantization: 12 bits (Fs 32 kHz, stereo 1, stereo 2), 16 bits (Fs 48 kHz, stereo) Video signal PAL color, CCIR standards Usable cassette Mini DV cassette with the mark printed Tape speed SP: Approx. 18.81 mm/s LP: Approx. 12.56 mm/s Recording/playback time SP: 60 min (using a DVM60 cassette) LP: 90 min (using a DVM60 cassette) Fast forward/rewind time Approx. 2 min 40 s (using a DVM60 cassette and rechargeable battery pack) Approx. 1 min 45 s (using a DVM60 cassette and AC Adaptor) Viewfinder Electric viewfinder (color) Image device 3.0 mm (1/6 type) CCD (Charge Coupled Device) Gross: Approx. 800 000 pixels Effective (movie): Approx. 400 000 pixels Lens DCR-HC23E: Carl Zeiss Vario-Tessar 20 × (Optical), 640 × (Digital) DCR-HC24E/HC26E/HC35E: Carl Zeiss Vario-Tessar 20 × (Optical), 800 × (Digital) Focal length f=2.3 ~ 46 mm (3/32 ~ 1 13/16 in.) When converted to a 35 mm still camera In CAMERA: 44 ~ 880 mm (1 3/4 ~ 34 1/32 in.) F1.8 ~ 3.1 Filter diameter: 25 mm (1 in.) Color temperature [AUTO], [ONE PUSH], [INDOOR] (3 200 K), [OUTDOOR] (5 800 K) Minimum illumination 5 lx (lux) (F 1.8) 0 lx (lux) (during NightShot plus function)*1 *1 Objects unable to be seen due to the dark can be shot with infrared lighting. Input/Output connectors Audio/Video output 10-pin connector Video signal: 1 Vp-p, 75 Ω (ohms), unbalanced Luminance signal: 1 Vp-p, 75 Ω (ohms), unbalanced Chrominance signal: 0.3 Vp-p, 75 Ω (ohms), unbalanced Audio signal: 327 mV (at load impedance 47 kΩ (kilohms)), Output impedance with less than 2.2 kΩ (kilohms) USB jack (DCR-HC23E/HC24E/HC26E) mini-B DV input/output (DCR-HC26E) i.LINK Interface (IEEE1394, 4-pin connector S100) DV output (DCR-HC23E/HC24E) i.LINK Interface (IEEE1394, 4-pin connector S100) LCD screen Picture 6.2 cm (2.5 type) Total dot number 123 200 (560 × 220) General Power requirements DC 7.2 V (battery pack) DC 8.4 V (AC Adaptor) Average power consumption During camera recording using the viewfinder 1.8 W During camera recording using the LCD 2.1 W Operating temperature 0 °C to 40 °C (32 °F to 104 °F) Storage temperature -20 °C to + 60 °C (-4 °F to + 140 °F) Dimensions (approx.) 65 × 79 × 113 mm (2 5/8 × 3 1/8 × 4 1/2 in.) (w/h/d) Mass (approx.) DCR-HC23E/HC24E/HC26E: 360 g (12 oz) main unit only 420 g (14 oz) including the NP-FP30 rechargeable battery pack and DVM60 cassette. DCR-HC35E: 370 g (13 oz) main unit only 430 g (15 oz) including the NP-FP30 rechargeable battery pack and DVM60 cassette. Audio signal: 327 mV (at load impedance 47 kΩ (kilohms)), Output impedance with less than 2.2 kΩ (kilohms) USB jack mini-B DV input/output i.LINK Interface (IEEE1394, 4-pin connector S100) AC Adaptor AC-L25A/L25B Power requirements AC 100 - 240 V, 50/60 Hz Current consumption 0.35 - 0.18 A Power consumption 18 W Output voltage DC 8.4 V*2 Operating temperature 0 °C to 40 °C (32 °F to 104 °F) Storage temperature -20 °C to + 60 °C (-4 °F to + 140 °F) Dimensions (approx.) 56 × 31 × 100 mm (2 1/4 × 1 1/4 × 4 in.) (w/h/d) excluding the projecting parts Mass (approx.) 190 g (6.7 oz) excluding the mains lead *2 See the label on the AC Adaptor for other specifications. Rechargeable battery pack (NP-FP30) Maximum output voltage DC 8.4 V Output voltage DC 7.2 V Capacity 3.6 Wh (500 mAh) Dimensions (approx.) 31.8 × 18.5 × 45.0 mm (1 5/16 × 3/4 × 1 13/16 in) (w/h/d) Mass (approx.) 40 g (1.5 oz) Operating temperature 0 °C to 40 °C (32 °F to 104 °F) Type Lithium ion Design and specifications are subject to change without notice. Supplied accessories See page 6. AC Adaptor (1) Mains lead (1) Handycam Station (1) (DCR-HC35E) Wireless Remote Commander (1) (DCR-HC24E/HC35E) A/V connecting cable (1) USB cable (1) (DCR-HC24E/HC35E) Lens cap (1) Rechargeable battery pack NP-FP30 (1) CD-ROM “Picture Package Ver.1.5.1” (1) 21-pin adaptor (1) (DCR-HC35E) Operating Guide (1) Handycam Station DCRA-C151 Input/Output connectors (DCR-HC35E) Audio/Video output 10-pin connector Video signal: 1 Vp-p, 75 Ω (ohms), unbalanced Luminance signal: 1 Vp-p, 75 Ω (ohms), unbalanced Chrominance signal: 0.3 Vp-p, 75 Ω (ohms), unbalanced

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 Model DCR-HC23E DCR-HC24E DCR-HC26 DCR-HC26E DCR-HC35E Destination AEP, EE, NE AEP, UK, EE, NE US, CND, E, AR NE, E, AUS, CH, AEP, UK, EE, NE BR, KR HK Color system PAL PAL NTSC PAL PAL DV Interface OUT OUT IN/OUT IN/OUT IN/OUT (Note) Remote commander × a × × a Cradle (Handycam Station) × × × × a CR board × × × × CR-061 Model information table • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model Note: DV Interface on the Cradle (Handycam Station)

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY. Unleaded solder Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 TABLE OF CONTENTS 1. SERVICE NOTE 1-1. Power Supply During Repairs ·········································1-1 1-2. To Take Out a Cassette when not Eject (Force Eject) ·····1-1 1-3. Setting the “Forced Power On” Mode ·····························1-1 1-4. Using Service Jig ·····························································1-2 1-5. Self-diagnosis Function ···················································1-2 1-6. Precaution on Replacing the VC-416 Board ···················1-4 2. DISASSEMBLY 2-1. Disassembly·····································································2-2 3. BLOCK DIAGRAMS 3-1. Overall Block Diagram (1/5) ···········································3-1 3-2. Overall Block Diagram (2/5) ···········································3-2 3-3. Overall Block Diagram (3/5) ···········································3-3 3-4. Overall Block Diagram (4/5) ···········································3-4 3-5. Overall Block Diagram (5/5) ···········································3-5 3-6. Power Block Diagram (1/3)·············································3-6 3-7. Power Block Diagram (2/3)·············································3-7 3-8. Power Block Diagram (3/3)·············································3-8 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. Frame Schematic Diagrams·············································4-1 4-2. Schematic Diagrams ························································4-3 4-3. Printed Wiring Boards ···················································4-25 4-4. Mounted Parts Location ················································4-37 5. REPAIR PARTS LIST 5-1. Exploded Views ·······························································5-2 5-2. Electrical Parts List ·······················································5-12 Section Title Page

1-1. POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so that the unit cannot operate. These following method is available to prevent this. Method: Use the AC power adaptor (AC-L25A/L25B). 1-2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) 1 Refer to “2. DISASSEMBLY” to remove the mechanism deck block. 2 Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment. Loading motor DC power supply (+ 4.5Vdc) 1-3. SETTING THE “FORCED POWER ON” MODE It is possible to turn on power by adjustment remote commander (RM-95 or NEW LANC JIG). Operate the VTR function using the adjustment remote commander. 1-3-1. Setting the “Forced Camera Power ON” Mode 1) Select page: 0, address: 01, and set data:01. 2) Select page: D, address: 10, set data:01 and press the “PAUSE (Write)” button of the adjustment remote commander. 1-3-2. Setting the “Forced VTR Power ON” Mode 1) Select page: 0, address: 01, and set data:01. 2) Select page: D, address: 10, set data:02 and press the “PAUSE (Write)” button of the adjustment remote commander. 1-3-3. Exiting the “Forced Power ON” Mode 1) Select page: 0, address: 01, and set data:01. 2) Select page: D, address: 10, set data:00 and press the “PAUSE (Write)” button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00.

1-5-1. Self-diagnosis Function When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or LCD screen what to do. This function consists of two display; self- diagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual. 1-5-2. Self-diagnosis Display When problems occur while the unit is operating, the counter of the viewfinder or LCD screen shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in which the problem occurred, and “detailed code” of the problem. 1 1 3 1 C Repaired by: Refer to “1-5-3. Self-diagnosis Code Table”. Indicates the appropriate step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again. Block Detailed Code Blinks at 3.2Hz C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer Viewfinder or LCD screen C : 3 1 : 1 1 1 8 CN1014 VC-416 BOARD (SIDE A) CPC-15 (J-6082-564-A) I/F unit for LANC control (J-6082-521-A) 1-4. USING SERVICE JIG Connect the CPC-15 jig connector (J-6082-564-A) and I/F unit for LANC conrol (J-6082-521-A) to the CN1014 of VC-416 board.

C C C C C C C C C C C C C C C C C C C C C C C C C C C C C Block Function 0 4 2 1 2 2 3 1 3 1 3 1 3 1 3 1 3 1 3 1 3 1 3 1 3 1 3 1 3 1 3 1 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 3 2 Detailed Code 0 0 0 0 0 0 1 0 1 1 2 0 2 1 2 2 2 3 3 0 3 1 4 0 4 1 4 2 4 3 4 4 1 0 1 1 2 0 2 1 2 2 2 3 3 0 3 1 4 0 4 1 4 2 4 3 4 4 Symptom/State Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. S reel side tape slacking when unloading. T reel fault. S reel fault. FG fault when starting capstan. FG fault during normal capstan operations. FG fault when starting drum. PG fault when starting drum. FG fault during normal drum operations. PG fault during normal drum operations. Phase fault during normal drum operations. LOAD direction loading motor time- out. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. S reel side tape slacking when unloading. T reel fault. S reel fault. FG fault when starting capstan. FG fault during normal capstan operations. FG fault when starting drum. PG fault when starting drum. FG fault during normal drum operations. PG fault during normal drum operations. Phase fault during normal drum operations. Self-diagnosis Code Repaired by: Correction Use the InfoLITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning.

(Cannot initialize focus.) Zoom operations fault (Cannot initialize zoom lens.) Focus lens initializing failure and zoom lens initializing failure occur simulta- neously. Self-diagnosis Code Repaired by: Correction Inspect the lens block focus reset sensor (Pin ql, of CN3101 of VC- 416 board) when focusing is performed when the touch panel is operated in the focus manual mode and the focus motor drive circuit (IC3101 of VC-416 board) when the focusing is not performed. Inspect the lens block zoom reset sensor (Pin qg, of CN3101 of VC-416 board) when zooming is performed when the zoom switch is operated and the zoom motor drive circuit (IC3101 of VC-416 board) when zooming is not performed. Inspect the flexible board for breakage or loose connection. If not faulty, inspect the focus and zoom motor drive circuit (IC3101 of VC-416 board). 1-6. PRECAUTION ON REPLACING THE VC-416 BOARD Exif Model Data Check When you replace to the repairing board, the written data of repairing board also might be changed to original setting. When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not, rewrite to the right value. Exif Model Data Writing Method: 1) Select page: 0, address: 01 and set data: 01. 2) Select page: C, address: D2 to D4, and set the Exif Model Data. Note: To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data. 3) Select page: 0, address: 01, and set data: 00. Page C C C Data DCR-HC23E 32 33 45 DCR-HC24E 32 34 45 DCR-HC26 32 36 00 Address D2 D3 D4 DCR-HC26E 32 36 45 DCR-HC35E 33 35 45

which comes off at the point. (Be careful or some pieces of gilt may be left inside) NOTE FOR REPAIR • Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. • When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped. • When installing a connector, dont’ press down at wire of connector. It is possible that a wire is snapped.

HELP HELP EXPLODED VIEW HARDWARE LIST 2-1 (Open the Cassette Lid) 2-4 (Claw) 2-5 (Shaft) 2-2 (#2) 2-3 (#2) 3-2 (#2) 3-4 (Boss) 3-1 (Open the Jack Lid) 3-5 2 NS Cabinet Assy 3 Front Panel Block 1 Cabinet (R) block 1-2 (#14) 1-4 (#14) 1-6 (#10) 1-13 1-14 1-15 1-7 (#10) 1-9 (#10) 1-5 (#14) 1-1 (Slide the EVF) 1-8 (Open the LCD) 1-3 (Direction of the arrowA) A 1-12 (Boss) 1-11 (Claw) 1-10 (Claw) 3-3 (#2)

EXPLODED VIEW HARDWARE LIST PD-281 HELP 3-1 3-2 1 Hinge block 3 LCD 2 PD-281 board 1-2 (#13) 1-3 (#12) 1-9 (#10) 1-14 (#3) 1-11 (Claw) 1-12 1-10 (#12) 1-6 (Boss) 1-7 (Boss) 1-5 (#12) 1-1 1-4 1-8 2-2 2-6 2-7 2-3 2-1 2-4 (#12) 2-5 (Claw) 2-8 (Claw) 1-13 1-15

HC35E 2 Lens Block 3 BT Panel Block 1 EVF block 2-3 2-1 (#3) 1-1 (#3) 2-2 (Boss) 1-3 1-2 (Boss) 2-4 3-1 (#2) 3-4 (#2) 3-5 (#2) 3-3 3-6 3-2 (Claw) EXPLODED VIEW HARDWARE LIST

VC-416 CR-061 HC35E US, CND 2-1 2-5 2-6 2-2 2-3 3-1 (Boss) 3-6 3-7 3-3 (Claw) 3-4 (Claw) 3-5 (Claw) 3-2 (Dirrection of the arrow) 2 VC-416 Board 3 Mechanism Deck 1 Bottom Frame 1-1 (#3) 2-4 (#3) 2-7 (Claw) 1-6 (Boss) (Except HC35E) 1-3 1-2 1-4 (#2) 1-5 3-8 EXPLODED VIEW HARDWARE LIST

THE METHOD OF ATTACHMENT OF FP-380 FLEXIBLE BOARD Adhesive tape Hinge cover (M) Claw Claw Claw Claw Adhesive tape Adhesive tape 1 Fold dotted line parts of the FP-380 flexible board as shown in figure. 3 Roll the the FP-380 flexible board 90 degrees. 2 Hang it on the claw after putting the FP-380 flexible board on the hinge cover (M). 4 Attach two hinge covers as shown in figure. Fold Fold

OVERALL BLOCK DIAGRAM (4/5) OVERALL BLOCK DIAGRAM (3/5) OVERALL BLOCK DIAGRAM (2/5) OVERALL BLOCK DIAGRAM (1/5) POWER BLOCK DIAGRAM (3/3) POWER BLOCK DIAGRAM (2/3) POWER BLOCK DIAGRAM (1/3) OVERALL BLOCK DIAGRAM (5/5)

FE_CLPOB V1 - V4, RG, VSHT, H1, H2 7 CCD IMAGER IRIS (SHUTTER) H M IRIS METER M FOCUS SENSOR ZOOM SENSOR FOCUS MOTOR ZOOM MOTOR M LENS BLOCK CCD OUT CN3101 12 8 9 19 LENS TEMP SENSOR IC3002 IC101 BUFFER Q101 IRIS DRIVE Q3101 HALL GAIN CONTROL Q3103 LED DRIVE Q1001 1 SI-051 BOARD (1/4) NIGHTSHOT PLUS CN605 (1/4) NS_LED_K 13 CN1004 (1/4) 24 (2/12) IRIS DRIVE I_DRIVE (-) I_BIAS (-) 6 I_BIAS (+) I_HALL (-) HALL_AD 7 I_HALL (+) FC_A, FC_XA, FC_B, FC_XB ZM_A, ZM_XA, ZM_B, ZM_XB FC_SENS_OUT 15 ZM_SENS_OUT 16 THERMO_OUT 17 NightShot_Vcc FC_RST ZM_RST LENS_TEMP_AD XNS_SW HALL AMP IC3105 (2/12) IC3104 (2/12) IC3101 FOCUS MOTOR DRIVE ZOOM MOTOR DRIVE 05 SPCK CAMERA/ MECHA CONTROL (7/12) IC8601 (1/2) OVERALL (5/5) (PAGE 3-5) 9 OVERALL (2/5) (PAGE 3-2) 1 209 216 214 215 212 213 190 LD_EN0, LD_DIR0A, LD_DIR0B LD_EN1, LD_DIR1A, LD_DIR1B FC_RST ZM_RST LD_EN0, LD_DIR0A, LD_DIR0B LD_EN1, LD_DIR1A, LD_DIR1B 14 15 DV SIGNAL PROCESS (3/12) IC6001 IR_ON B6 A13 R22 P20 D17 Y18 Y5 K1 CN3001 14 CLPDM, PBLK, XSHP, XSHD VCK VCK XRST_VTR CAM_DD_ON XRST_VTR XRST_VTR TG_AHD, TG_AVD TG_ZSG1 TG_ZV1 TG_ID TG_VGAT XRST_VTR CAM_DD_ON XCS_TG XCS_TG CS_CH, CH_SO, CH_SCK CS_CH, CH_SO, CH_SCK CAM_SO, CAM_SCK CAM_SI, CAM_SO, CAM_SCK CAM SI, CAM_SO, CAM_SCK CAM_SI, CAM_SO, CAM_SCK 46 - 48 39 XTAL AMP HALL REG IC3103 (2/12) IC9201 EVR (D/A CONVERTER) (2/12) FREQ_AMPOUT FREQ_TUNE 7 5 1 1 2 3 8 1 7 HALL GAIN 5 7 HALL_OFFSET 5 HALL_GAIN 6 IRIS_PWM, IRIS_COM 3 HALL BIAS 1 3 2 TRCKO 143 IC6002 DV INTERFACE (3/12) 19 LCKO 159 62 78 177 XCS_IC_6002 XCS_IC_6002 LBUS0 - LBUS3 USB_D+, USB_D- USB_D+, USB_D- USB_DET D24A00 - D31A07, DXXA08, DXXA09, ALE, WRX, RDX D24A00 – D31A07, DXXA08, DXXA09, ALE, WRX, RDX USB_D+ USB PULL UP USB_3.1V Q6003 78 77 96 OVERALL (2/5) (PAGE 3-2) 2 OVERALL (4/5) (PAGE 3-4) 4 OVERALL (3/5) (PAGE 3-3) 3 OVERALL (4/5) (PAGE 3-4) 5 OVERALL (3/5) (PAGE 3-3) 6 OVERALL (4/5) (PAGE 3-4) 7 OVERALL (2/5) (PAGE 3-2) 8 RECDT RECA1, RECA2 RECCK RFIN DATA_TO_SFD SFD_BCK DATA_FROM_SFD SFD_FCK SFD_LRCK IC_6001_C_OUT IC_6001_Y_OUT 63 68 64 69 67 110 113 121 123 119 141 PANEL_R PANEL_G PANEL_B PANEL_HD, PANEL_VD OSD_V OSD_V CAM_DD_ON VFO_VD, VFO_OE USB_DET MERODY_ENV MERODY_CARR USB_ON XUSB_EN VREF LINE_OUT_VD 189 XCS_IC_6001 FRRV, TRRV, TRRT 193 XCS_IC_6001-2 197 XIRQ_IC_6001 192 181 182 129 SWP 161 DRP 162 XCS_SFD 187 XCS_VFD 188 Y17 C22 D6 B3 N20 W20 B7 J2 B8 N22 A21 B21 E23 B2 VD_SO, XCS_VD, VD_SCK XCS_VD, VD_SI, VD_SO, VD_SCK VD_SI, VD_SO, VD_SCK VSP_SO, XVSP_SCK VSP_SO, XVSP_SCK VSP_SI, VSP_SO, XVSP_SCK VSP_SI, VSP_SO, XVSP_SCK SWP U1 XCS_EVF V22 EVF_BL_ON AB9 PANEL_BL_ON U2 XCS_AU1 AC18 BEEP D8 D606 IR EMITTER/ NIGHTSHOT TPA+, TPA-, TPB+, TPB- AD0 - AD9 A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL A : VIDEO/AUDIO/SERVO SIGNAL 3 - 6, 8 - 11 4 - 1 24 - 21 12 - 9, 7 - 4 1, 2, 15, 16 44, 45 19, 21 - 23 2 - 11 199 - 208 196 - 194 180 - 178 157 - 154 164 - 176 184 - 186 18 - 20 24, 26 - 28 52, 51, 48, 47 18, 21, 22, 25, 26, 28, 31, 33 1 - 4, 9, 10, 12, 13 35, 38, 37 2, 23, 4, 21 5, 19, 17, 7 6, 7 9 - 12 13 - 16 4, 3 11, 5, 6 12, 8, 9 Y6, AC9, Y9 L2, D15, A16 Y11, AB11, AB10 AC5, Y12, AC12, Y13 AC8, AB8, AC7 AA2, Y2, W4, W2, Y1, V4, V2, W1, P2, P1, K4, L1, L4 Y16, AC17 42, 43 75, 76 131, 130 126, 127 2 - 4, 6 - 9 11, 75 - 77 A7, Y8 XPWAD, XPWDA M20, L20 Q8601, Q8602 MODULATOR 3. BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. A : VIDEO/AUDIO/SERVO SIGNAL A : SERVO SIGNAL DRUM_PWM 05 IC8601 (2/2) VC-416 BOARD (2/5) IC9001 (3/3) IC2201 (1/2) CAP_PWM DRUM_ERROR CAP_ERROR DRUM MOTOR DRIVE FG AMP PG AMP 53 50 52 49 21 20 18 MECHA CONTROL (7/12) Q2208 CN1009 DRUM FG M901 DRUM MOTOR DRUM_VS LOADING MOTOR DRIVE TAPE END DETECT 43 45 LPF Q2207 10 CAPSTAN MOTOR DRIVE FG AMP 4 DRUM_U, V, W LM ± LOAD, UNLOAD TAPE_END_C DRUM_FG DRUM_PG CAP_VS CAP_FWD, CAP_ON CAP_FWD, CAP_ON CAP_FG DRUM_FG DRUM_PG DEW_AD MODE_SW_A - MODE_SW_C MODE_SW_A - MODE_SW_C LOAD, UNLOAD TAPE_END TAPE_LED_ON TAPE_END CAP_FG 9 28 16 25 11 18 TAPE_TOP_C T_REEL ± S_REEL ± TAPE TOP DETECT T REEL FG AMP S REEL FG AMP DEW_AD UHE±, VHE±, WHE± CAP U, V, W CN1007 6 M DRUM PG M903 CAPSTAN MOTOR M HU, HV, HW DEW SENSOR MODE SWITCH S902 Q9002 M902 LOADING MOTOR Q901 TAPE END SENSOR D901 TAPE LED M FG1, FG2 CAPSTAN FG Q902 TAPE TOP SENSOR H902 T REEL SENSOR H901 MIC902 S903 CC DOWN REC PROOF S REEL SENSOR 4PIN CONNECTOR (8/12) IC9001 (1/3) (8/12) IC9001 (2/3) (8/12) DRUM/ CAPSTAN PWM DRIVE (11/12) 21 7 24 8 FG PG LED DRIVE TAPE_LED_K 1 IC8602 64k EEPROM (7/12) D1 C1 X8601 20MHz XCS_EEP F1 SERIAL INTERFACE 38, 36 77, 78 64, 67 63, 65, 68 74, 76, 78 75, 77 1, 80 10 - 15 7, 8 75, 76 37 XCS_IC_9001 34 XRST_VTR OVERALL (1/5) (PAGE 3-1) 1 OVERALL (1/5) (PAGE 3-1) 8 F2 XSYS_RST F4 SIRCS_SIG A10 LM_LIM_DET LM_LIM_DET 41 44 35 SPCK SPCK EEP_SI, EEP_SO, EEP_SCK OVERALL (1/5) (PAGE 3-1) 2 OVERALL (5/5) (PAGE 3-5) 10 REC_PROOF CHIME_SDA, CHIME_SCK XRST_VTR IC_8001_SI, IC_8001_SO. IC_8001_SCK. XCS_IC_8001 VIDEO HEAD CN1008 RF_MON ODD XODD, YODD XEVEN, YEVEN SWP CN1014 EVEN SWP IC6501 REC/PB AMP (4/12) XCS_EEP 2 4 7 - 5 1 30 44 35 46 38 CPC (FOR CHECK) CONT1, SW_PS, ALL_PS CONT1, SW_PS, ALL_PS RECDT RECA1, RECA2 RECCK RFIN RF_MON N MECHA DECK (MDX-N110) VSP_SO, XVSP_SCK VSP_SO, XVSP_SCK SWITCHING SWITCHING 31 Y14 AC15 N4 B9 A9 D10, B10 D19, B20 D11 V23 H4 L22 19 N2 TAPE_TOP TAPE_TOP 29 B11 TREEL_FG TREEL_FG A11 25 SREEL_FG SREEL_FG REC_PROOF CHIME_SDA, CHIME_SCK XCC_DOWN XCC_DOWN B15 AA22 SWP EEP_SI, EEP_SO, EEP_SCK ZOOM_VR_AD SYS_V D14 M22 2, 5, 6 A18, N1, M4 Y7, AB7, AB6, AC6 AB14, AC14, AB13 G4, H2 32, 33 40, 42 10, 9 3, 4 39, 37, 45 69, 72 26, 27 22, 23 AB20 - AB22 XFFREW_UP Q9004 AC13 1 - 6 CN1010 20 - 9 2 - 7 7 - 9 1 - 4 20, 19 22, 23 13, 14 27, 24 6, 5 2, 3

OVERALL (1/5) (PAGE 3-1) 6 OVERALL (5/5) (PAGE 3-5) 11 OVERALL (1/5) (PAGE 3-1) 3 05 A : VIDEO SIGNAL PANEL_R PANEL_G PANEL_B TP_Y TP_SEL1 TP_X XCS_EVF EVF_BL_ON PANEL_BL_ON PANEL_HD, PANEL_VD LB-121 BOARD COLOR EVF UNIT PD-281 BOARD (1/2) FP-380 FLEXIBLE BOARD (1/2) EVF BACKLIGHT DRIVE Q9306 CN9604 5 2 6 3 TP_L TP_R TP_BOT TP_TOP TOUCH PANEL TOUCH PANEL I/F Q9601, Q9602 2.5 inch COLOR LCD UNIT 34 21 22 26 10 28 20 42, 45, 44 5, 11, 18 48, 1 R G B COM, CS COM_P EVF_COM_CS EVF_STBY EVF_STB STB LED_K COM RGT_P, DWN_P, XSTBY_P RGT, DWN, XSTBY RGT, DWN, XSTBY CN9605 HCK1, HCK2, HST, PCG, EN, VCK, VST, WIDE, PSIG, REF 33 32 6 - 9, 12, 14, 16, 17, 24, 30 LCD901 31 5 3 7 6 1 2 43 3 LCD BACKLIGHT DRIVE Q9301 - Q9304 XSYS_RST VR VG VB COM, CS 18 16 17 CN302 D302 (BACKLIGHT) D9603 - D9605 (BACKLIGHT) EVF_VR EVF_VG EVF_VB EVF_COM_CS 14 13 17 15 CN9301 EVF_HCK1, EVF_HCK2, EVF_HST, EVF_PCG, EVF_EN, EVF_VCK, EVF_VST, WIDE, EVF_VP, EVF_REF HCK1, HCK2, HST, PCG, EN, VCK, VST, WIDE, PSIG, REF HCK1, HCK2, HST, PCG, EN, VCK, VST, BLK, PSIG, REF EVF_HCK1, EVF_HCK2, EVF_HST, EVF_PCG, EVF_EN, EVF_VCK, EVF_VST, EVF_BLK, EVF_PSIG, EVF_REF LCD/EVF DRIVE (6/12) IC9301 LCD/EVF BACKLIGHT CONTROL (6/12) IC9302 LCD902 20 7 8 4 6 CN301 1 7 14 11 VD_SI, VD_SO, VD_SCK CN9302 (1/2) 1 2 3 30 14 16 15 PANEL_VR PANEL_VG PANEL_VB TP_Y TP_SEL1 BL_H1 - BL_H3 TP_X CN9601 (1/2) 30 29 28 17 15 16 19 - 23, 29, 28, 18, 24, 17 3 - 6, 8 - 12, 16 21, 19 18 - 15, 13 - 9, 5 5 - 7, 9 - 15, 20 5 3 4 24, 23 6 - 9, 11 - 13, 20 - 22 2, 19, 14 27 - 25 1 12 - 82, 2, 3, 13, 7, 14 4 - 6 11 - 9 20 - 22 3-3. OVERALL BLOCK DIAGRAM (3/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. CR-061 BOARD (1/2) 05 SP± SP± SP901 SPEAKER L CN602 1 3 R MIC901 MICROPHONE SI-051 BOARD (2/4) CONTROL KEY BLOCK (CF17000) (1/2) VC-416 BOARD (4/5) INT_MIC_L INT_MIC_R CN605 (2/4) 18 19 CN1004 (2/4) 19 18 INT_MIC_L INT_MIC_R VIDEO OUT, AUDIO I/O (5/12) IC6701 IC6702 A/D, D/A CONVERTER (5/12) 37 45 38 17 8 9 12 10 11 15 41 23 24 12 9 7 CN1004 (3/4) CN1001 1, 2 13, 14 21, 20 1, 3 VSP_SO, XVSP_SCK VSP_SO, XVSP_SCK OVERALL (1/5) (PAGE 3-1) 4 OVERALL (1/5) (PAGE 3-1) 7 OVERALL (5/5) (PAGE 3-5) 12 DATA_TO_SFD SFD_BCK DATA_FROM_SFD RECOUT_L PBIN_L SFD_FCK SFD_LRCK 19 47 BEEP XCS_AU1 XPWAD, XPWDA IC_6001_C_OUT IC_6001_Y_OUT RECOUT_R PBIN_R OVERALL (1/5) (PAGE 3-1) 5 CN601 CN002 (1/2) VIDEO_I/O MULTI_JACK_IN AUDIO_L_I/O AUDIO_R_I/O S_C_I/O S_Y_I/O VIDEO_I/O MULTI_JACK_IN MULTI_JACK_IN AUDIO_L_I/O AUDIO_R_I/O S_C_I/O S_Y_I/O VIDEO_I/O AUDIO_L_I/O AUDIO_R_I/O S_C_I/O S_Y_I/O VIDEO IN/OUT S-C S-Y JACK AD AUDIO R AUDIO L SI-051 BOARD (3/4) CN003 (1/2) 15 14 12 13 6 7 CN1006 (1/2) 15 17 10 11 13 12 MULTI_JACK_IN_CRADLE LANC_SIG CRADLE (1/2) 8 10 13 9 10 5 9 1 6 7 14 18 A/V OUT CN605 (3/4) (USB) CN604 DV OUT DV 1 CN603 TPA, NTPA, TPB, NTPB D+, D- VCC USB_DET USB_DET D608 1 29 - 32 35, 34 8 - 5 4 - 1 2, 3 3, 2 8 - 5 3, 2 31, 29, 33, 35 36 USB_DET D1023 1 22 20 27 26 24 25 29 - 32 34, 35 32, 34 24, 26 36 24 LANC_SIG LANC_SIG 9 2 28 LANC_SIG LANC_SIG 20 25 17 31 30 25 23 22 16 15 25 26 2 3 USB_DET A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL NON CRADLE model DCR-HC23E/HC24E NON CRADLE model: DCR-HC23E/HC24E /HC26/HC26E CRADLE model: DCR-HC35E CRADLE model DCR-HC26/HC26E TPA, NTPA, TPB, NTPB TPA+, TPA-, TPB+, TPB- TPA, NTPA, TPB, NTPB USB_D+, USB_D- USB_D+, USB_D- USB_D+, USB_D- VIDEO_I/O MULTI_JACK_IN AUDIO_L_I/O AUDIO_R_I/O S_C_I/O S_Y_I/O USB_DET/VBUS TPA, NTPA, TPB, NTPB USB_D+, USB_D-

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. DC IN J001 CN9603 CN9602 3, 4 05 HI CONTROL (9/12) IC8001 D7 J5 J4 F9 J9 H8 X8001 32.768kHz BT601 LITHIUM BATTERY + – C BH001 BATTERY TERMINAL G1 G2 E8 E9 B6 C2 B1 B9 J6 F7 Q8001 BATTERY CHARGE DETECTOR SIRCS_SIG XVTR_LED XPOWER_SW XMODE_SW XCAM_LED XEJECT_SW ZOOM_VR KEY_AD3 KEY_AD3 BATT_INFO XBATT_INFO_SW XRESET XCHARGE_LED SI-051 BOARD (4/4) VC-416 BOARD (5/5) 1 REMOTE SENSOR IC601 CN605 (4/4) 15 CN1004 (4/4) 22 LI_3V 14 23 LANC_IN LANC_OUT XLANC_PWR_ON XLANC_ON VTR_DD_ON XCS_DD CAM DD ON BATT_IN HI_EVER_SO, HI_EVER_SCK IC2201 (2/2) D_1.5V MT_5V D_2.8V (NS_2.8V) RP_2.8V A_2.8V A_2.8V (EP_2.8V) VTR_UNREG C/D_UNREG MT/15.5/BL_UNREG D_2.8V DC CONTROL, RESET, LANC DRIVE (11/12) 57 54 56 F3 F2 55 52 44 13 5 D8 B2 B5 D9 50 A9 AU_4.6V EVER_3.0V CAM_15V AU_2.8V IC_9001_13.5V EP_8.5V CAM_-7.5V USB_3.1V LANC_DC VOUT A_4.6V RP_4.6V A_4.6V (EP_4.6V) 51 45 46 14, 15 C1, D3 KEY_AD5 KEY_AD2 5 13 CN1012 CONTROL KEY BLOCK (SS17000) S003 (PHOTO FREEZE) S002 (PHOTO REC) PHOTO START/STOP REC S004 RV001 (ZOOM) W T 1 11 CAMERA D003 3 9 10 4 PLAY/EDIT D002 S001 (EJECT) POWER CONTROL KEY BLOCK (SB9000) S001 S002 S003 (ZOOM) T W 4 5 3 S101 (PANEL REVERSE) PANEL_REV 2ND_ZOOM(T) 2ND_ZOOM(W) 2ND_S/S_SW FP-386 FLEXIBLE BOARD RESET S005 LI_3V S001 PANEL OPEN/CLOSE EASY CHG S003 BACK LIGHT S002 CONTROL KEY BLOCK (CF17000) (2/2) DISP/ BATT INFO S004 D001 CN1017 5 3 7 1 CN9601 (2/2) KEY_AD1 KEY_AD1 KEY_AD1 KEY_AD5 KEY_AD2 KEY_AD3 PD-281 BOARD (2/2) FP-380 FLEXIBLE BOARD (2/2) 18 CN9302 (2/2) 13 G8 B7 A7 B8 A8 B3 A3 B4 FP-381 FLEXIBLE BOARD CN2001 19 - 23 13 - 17 24 7 1 - 5 8 - 12 XRESET C6 LANC_SIG XRESET CR-061 BOARD (2/2) CN002 (2/2) LANC_SIG CN003 (2/2) CN1006 (2/2) 1 - 7 36 - 30 ACV_UNREG ACV_UNREG ACV_UNREG ACV_GND BATT_UNREG BATT_GND CRADLE (2/2) 1 - 4 BATT/XEXT BATT/XEXT BATT/XEXT 16 21 21 Q2003, Q2004 LF2001 INIT_CHARGE_ON D2006 R2010 BATT_SIG BATT/XEXT FAST_CHARGE Q2001, Q2002, Q2006 VTR_UNREG C/D_UNREG MT/15.5/BL_UNREG BATT_UNREG Q2005 DOUBLE INSERTION DETECT NON CRADLE model: DCR-HC23E/HC24E /HC26/HC26E CRADLE model: DCR-HC35E CRADLE model CRADLE model CRADLE model DCR-HC24E/HC35E NON CRADLE model OVERALL (1/5) (PAGE 3-1) 9 OSD_V CAM_DD_ON XSYS_RST XSYS_RST SIRCS_SIG OVERALL (2/5) (PAGE 3-2) 10 IC_8001_SI, IC_8001_SO, IC_8001_SCK, XCS_IC_8001 XCC_DOWN ZOOM_VR_AD SYS_V OVERALL (3/5) (PAGE 3-3) 11 TP_Y TP_SEL1 TP_X OVERALL (4/5) (PAGE 3-4) 12 MULTI_JACK_IN MULTI_JACK_IN_CRADLE D1, D2, E1, E2 TP_SEL2 H6 A6 G6 H2 TP SELECT SWITCH Q8002 ON OFF (CHG) MODE R8047 CRADLE model REC START/STOP

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. POWER (2/3) (PAGE 3-7) A 05 CN2001 FAST_CHARGE INIT_CHARGE_ON VTR_UNREG VTR_UNREG D_1.5V MT_5V D_2.8V (NS_2.8V) RP_2.8V A_2.8V A_4.6V AU_4.6V A_4.6V (EP_4.6V) RP_4.6V USB_3.1V IC_9001_13.5V EP_8.5V CAM_15V EVER_3.0V CAM DD ON CAM_-7.5V D_2.8V AU_2.8V A_2.8V (EP_2.8V) VTR_UNREG C/D_UNREG MT/15.5/BL_UNREG BATT/XEXT ACV_UNREG ACV_GND BATT_UNREG BATT_GND BATT_UNREG BATT_SIG BATT_SIG BATT/XEXT 7 19 - 23 13 - 17 24 1 - 5 8 - 12 BH001 BATTERY TERMINAL C + − DC IN J001 LF2001 FP-381 FLEXIBLE BOARD VC-416 BOARD (1/3) CR-061 BOARD CN002 LANC_DC LANC_DC CN003 18 CN1006 19 1 - 7 36 - 30 ACV_UNREG ACV_UNREG CRADLE 27 1 - 4 BATT/XEXT BATT/XEXT 16 21 21 CRADLE model Q2003, Q2004 D2006 R2010 Q2005 DOUBLE INSERTION DETECT NON CRADLE model BT601 LITHIUM BATTERY LI_3V CN1004 (1/2) SI-051 BOARD (1/2) 10 CN605 (1/2) 14 23 27 LANC DC LANC_DC F004 F002 F003 HI CONTROL (9/12) IC8001 C6 E8 E9 G1 G2 C1, D3 Q8001 D8 B2 B5 D9 BATTERY CHARGE DETECTOR A9 XLANC_POWER_ON XLANC_ON XCS_DD BATT_IN VTR_DD_ON H7 J7 BATT_SENSE ACV_SENSE FR_EVER_SO FR_EVER_SCK BATT_SIG XLANC_PWR_ON XLANC_ON VTR_DD_ON XCS_DD BATT_IN INIT_CHARGE_ON FAST_CHARGE BATT/XEXT D_2.8V D_2.8V IB_SO IB_SI INIT_CHARGE FAST_CHARGE BATT/EXT VOUT HI_EVER_SO, HI_EVER_SCK IC2201 DC CONTROL, RESET, LANC DRIVE, DRUM/CAPSTAN PWM DRIVE (11/12) 44 13 55 52 CAM_DD_ON 5 50 45 49 64 12 46 58 14, 15 D2201 VCC2 60 VCC3 61 VCC1 WAKE_UP XCTL2 LD REG6CTL OUTC1 CTL1 DIN CLK VBATT VOUT3 VOUT4 OUT1-1 62 VB 63 VCCO1 67 VCCO2 IN1 OUT2 VS2 IN2 OUT3-1 IN3 L2201 L2209 SWITCHING Q2201 CAPSTAN/ DRUM SWITCHING Q2207, Q2208 65 VS1 68 69 VS3 71 11 L2202 SWITCHING Q2204 70 10 L2203 SWITCHING Q2202 OUT4 VS4 IN4 73 74 9 L2204 L2208 L2213 L2214 L2212 L2211 SWITCHING Q2206 IN7 6 VOUT VDD ON/OFF L2216 L2219 L2217 VOUT1 48 VOUT2 47 L2207 SWITCHING Q2209 8.5V REG Q2212 15V REG Q2211 OUT7 79 VCONT5 1 VOUT5 2 -7.5V REG Q2213, Q2214 VCONT6 3 VOUT6 4 3.1V REG (11/12) IC2202 4 3 1 D2205 D2204 D2203 D2202 D_2.8V CHARGE_LED_VDD CONTROL KEY BLOCK (CF17000) D001 CN1017 4 8 NON CRADLE model: DCR-HC23E/HC24E /HC26/HC26E CRADLE model: DCR-HC35E CHG FUCTION KEY Q2001, Q2002, Q2006 CRADLE model CN601 A/V OUT 4 XPOWER_SW XMODE_SW CN1012 (1/2) CONTROL KEY BLOCK (SS17000) (1/2) 9 10 POWER B8 A8 ON OFF (CHG) MODE D 2.8V POWER (3/3) (PAGE 3-8) B XPOWER_SW XMODE_SW

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. VC-416 BOARD (2/3) CN1007 12 26 21 CN1010 8 25 - 26 05 D17 CAM_DD_ON N23 CHIME_PWR_CONT CAMERA/MECHA CONTROL (7/12) IC8601 F22 XREEL_HALL_ON DRUM/ CAPSTAN/ LOADING MOTOR DRIVE (8/12) IC9001 CHIME_VDD HE_VCC HALL_VCC 17 VH FG_VCC 3 VMR POWER (1/3) (PAGE 3-6) A L6702 L6704 L6701 VIDEO OUT, AUDIO I/O (5/12) IC6701 3.4V REG Q6701 FB8602 64k EEPROM (7/12) IC8602 L101 L6002 DV SIGNAL PROCESS (3/12) IC6001 DV INTERFACE (3/12) IC6002 Q8605 Q9003 TAPE_LED_A FB3003 FB3004 IC6702 A/D, D/A CONVERTER (5/12) L6003 L6004 L6006 L6009 FB6001 FB6002 HU, HV, HW CAPSTAN FG MIC902 4PIN CONNECTOR D901 TAPE LED H901 S REEL SENSOR H902 T REEL SENSOR TIMING GENERATOR (1/12) IC3001 S/H, AGC, A/D CONVERTER (1/12) IC3002 CN3001 CN101 CD-631 BOARD CCD IMAGER 3 IC101 12 2 13 FOCUS/ZOOM MOTOR DRIVE (2/12) IC3101 L3001 L3101 VTR_UNREG D_1.5V D_1.5V MT_5V A_2.8V AU_4.6V L6502 L6501 IC6501 REC/PB AMP (4/12) RP_2.8V RP_4.6V USB_3.1V IC_9001_13.5V VTR_UNREG IC_9001_13.5V CAM_15V CAM_DD_ON CAM_-7.5V CAM_15V CAM_-7.5V VH VL D_2.8V AU_2.8V HALL BIAS/ HALL GAIN CONTROL (2/12) IC3105 IRIS DRIVE, HALL AMP (2/12) IC3104 LENS BLOCK ZOOM SENSOR FOCUS SENSOR IRIS METER CN3101 11 20 13 I_DRIVE(+) ZM_SENS_Vcc ZM_RST_LED, FC_RST_LED FC_SENS_Vcc Q3102 HALL REG, XTAL AMP (2/12) IC3103 EVR (D/A CONVERTER) (2/12) IC9201 A_4.6V MT_5V A_2.8V A_2.8V D_2.8V D_2.8V A 4.6V AC3, AB4 ZM_RST_LED FC_RST_LED L3102 N MECHA DECK (MDX-N110)

POWER (1/3) (PAGE 3-6) B CONTROL KEY BLOCK (SS17000) (2/2) D_2.8V D_2.8V CN1012 (2/2) MODE_LED_VDD 7 12 RV001 (ZOOM) T W CAMERA D003 PLAY/EDIT D002 6 CN9302 25 D_2.8V D_2.8V (NS 2.8V) VDD_P XSTBY PD-281 BOARD 18 CN9605 VDD 14 XSTBY CN9601 25 6 8 D_2.8V D_2.8V 23 POFF 2.5 inch COLOR LCD UNIT LCD901 Q9307, 9308 SI-051 BOARD (2/2) D606 IR EMITTER /NIGHTSHOT REMOTE SENSOR IC601 CN605 (2/2) 12 CN1004 (2/2) 25 05 DCR-HC24E/HC35E LB-121 BOARD 2 CN302 VDD 1 CN9301 19 CN301 2 20 L9302 L9301 L9303 EVF_VDD EP_4.6V COLOR EVF UNIT D302 (BACKLIGHT) LCD902 LCD/EVF DRIVE (6/12) IC9301 LCD/EVF BACKLIGHT CONTROL (6/12) IC9302 EP_8.5V A_4.6V (EP_4.6V) A_2.8V (EP_2.8V) 2 XSTBY_P A_OUT 18 1 LCD BACKLIGHT DRIVE Q9301 - Q9304 D9603 - D9605 (BACKLIGHT) BL_H1 - BL_H3 11 - 9 20 - 22 TOUCH PANEL I/F Q9601, Q9602 3-8. POWER BLOCK DIAGRAM (3/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS FRA SI-051 BOARD (SIDE B) FELXIBLE FLAT CABLE (FFC-063) FLEXIBLE FLAT CABLE (FFC-060) M M M IC8602 (EEPROM) LB-121 BOARD (SIDE A) 1 20 1 2 21 20 CN301 CN302 11 12 13 14 16 510 CN601 A/V OUT CN604 DV CN603 USB 29 1 FP-228 FLEXIBLE BOARD FP-032 FLEXIBLE BOARD FP-031 FLEXIBLE BOARD N MECHANISM DECK (MDX-N110) CONTROL KEY BLOCK (SS17000) CONTROL KEY BLOCK (SB9000) CONTROL KEY BLOCK (CF17000) 1 20 20 1 FP-379 FLEXIBLE BOARD 1 30 1 30 FP-380 FLEXIBLE BOARD FP-381 FLEXIBLE BOARD 1 24 LEVEL3 VC-416 BOARD (SIDE B) LEVEL3 VC-416 BOARD (SIDE A) FP-386 FLEXIBLE BOARD 1 6 MIC901 MICROPHONE BT601 LITHIUM BATTERY SP901 SPEAKER LENS BLOCK TOUCH PANEL LCD901 2.5 INCH COLOR LCD UNIT LCD902 COLOR EVF UNIT FOR CHECK M902 LOADING MOTOR M903 CAPSTAN MOTOR M901 DRUM MOTOR VIDEO HEAD C CD-631 BOARD (SIDE B) 1 14 CN101 1 30 1 6 1 6 1 6 1 24 CN9601 CN9602 CN9603 CN9604 CN9605 PD-281 BOARD (SIDE A) 1 4 2 36 1 35 CN602 CN605 1 2 4 5 7 6 1 2 3 4 5 6 1 1 4 2 FLEXIBLE FLAT CABLE (FFC-060) CN002 MULTI CONNECTOR CR-061 BOARD 41 1 42 2 44 43 1 36 CN003 CRADLE model NON CRADLE model NON CRADLE model: DCR-HC23E/HC24E/HC26/HC26E CRADLE model: DCR-HC35E 1 2 23 24 1 2 2 36 1 35 2 1 28 29 1 2 26 27 1 14 1 8 1 2 7 8 1 2 19 20 1 2 29 30 1 2 23 24 1 2 13 14 CN3101 CN1001 CN1006 CN1007 CN1010 CN1012 CN1014 CN1017 CN9301 CN9302 CN2001 CN3001 36 1 1 10 1 10 CN1004 CN1008 CN1009 J001 DC IN BH001 BATTERY TERMINAL

CR-061 BOARD (CRADLE TERMINAL) FP-380 FLEXIBLE BOARD FP-386 FLEXIBLE BOARD (PANEL REVERSE DETECT) SI-051 BOARD (AV/DV/USB CONNECTOR) CONTROL KEY BLOCK (SB9000) LB-121 BOARD (EVF, EVF BACKLIGHT) FP-031, FP-032, FP-228 FLEXIBLE BOARD CD-631 BOARD (CCD IMAGER) PD-281 BOARD (LCD, LCD BACKLIGHT) CONTROL KEY BLOCK (SS17000) CONTROL KEY BLOCK (CF17000) Link Link 4-2. SCHEMATIC DIAGRAMS COMMON NOTE FOR SCHEMATIC DIAGRAMS

4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS 1. Connection 2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain. When indicating parts by reference number, please include the board name. (For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µ µF. 50 V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10 W unless otherwise noted. kΩ=1000 Ω, MΩ=1000 kΩ. • Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. • Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. • Parts with ★ differ according to the model/destination. Refer to the mount table for each function. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2: non flammable resistor • 5: fusible resistor • C: panel designation • A: B+ Line • B: B– Line • J : IN/OUT direction of (+,–) B LINE. • C: adjustment for repair. • A: not use circuit (Measuring conditions voltage and waveform) • Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 MΩ input impedance is used) • Voltage values change depending upon input impedance of VOM used.) Kinds of capacitor Case size External dimensions (mm) Yellow A A B B A=B Fig. a (Video output terminal output waveform) H Cyan Green White Magenta Red Blue Fig.b (Picture on monitor TV) CRT picture frame Electronic beam scanning frame THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) Pattern box Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A Color bar chart For PTB-450: J-6020-250-A For PTB-1450: J-6082-559-A Pattern box Front of the lens L = 1 m (PTB-450) L = 40 cm (PTB-1450) L Camera Precautions for Replacement of Imager • If the imager has been replaced, carry out all the adjustments for the camera section. • As the imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie. 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

R:REC MODE P:PB MODE Note: IC101 is not included in CD-631 complete board. Note: Voltages of IC101 can not be measured, because this is mounted by side of the lens. NTSC PAL R0.3/P0 R11.1 /P0 R14.7/P0 3300 R101 C102 10p 2SC3931-BCD-TX Q101 IC101 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16V 10u C101 16V 10u C104 14P CN101 1 2 3 4 5 6 7 8 9 10 11 12 13 14 CL101 CL102 CL103 L101 10uH 1 A V3 H1 VSHT V2 H2 CCD_OUT VL V4 VH RG V1 VL V3 H2 V_DRAIN V1 V2 VH GND VSHT V4 RG H1 CCD_OUT GND GND GND GND IC101 CCD IMAGER BUFFER CN3001 PAGE 4-6 VC-416 (1/12) of LEVEL3 THROUGH THE FLEXIBLE FLAT CABLE (FFC-063) 05 B D XX MARK:NO MOUNT 5 3 CD-631 BOARD 6 2 C CCD IMAGER 7 4 ICX610NKF: ICX611NKF:

Pages from 4-6 to 4-17 are not shown.

XX Q9603 C9602 XX XX R9601 C9604 XX R9606 XX D9601 XX 1 2 6 5 4 3 C9601 XX XX R9610 XX R9608 XX R9609 XX R9611 XX D9606 XX D9608 XX D9607 XX R9605 NO MARK:REC/PB MODE CONTROL KEY BLOCK (SB9000) is replaced as block, so that PRINTED WIRING BOARD is omitted. (PRINTED WIRING BOARD is omitted.) 0 2.8 2.8 2.8 2.8 0 2.8 0 2.8 2.8 1500 R9603 CN9603 6P 1 2 3 4 5 6 LND901 CH_GND 1M R9607 1200 R9602 MAZS056008S0 D9602 0.1u C9606 C9603 0.0022u 6P CN9602 1 2 3 4 5 6 CN9604 6P 1 2 3 4 5 6 24P CN9605 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 R9604 2200 1u C9605 Q9602 XP411F-TXE 6 2 1 3 5 4 Q9601 XP421F-TXE 6 2 1 3 5 4 D9604 NSSW008CT-T071 D9605 NSSW008CT-T071 D9603 NSSW008CT-T071 30P CN9601 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 LND005 LND004 LND003 S003 1 3 2 4 S002 1 3 2 4 S001 1 3 2 4 LND001 LND006 LND002 LND102 LND105 LND103 LND106 LND104 S101 LND101 LND013 LND008 LND017 LND018 LND023 LND028 LND002 LND023 LND004 LND027 LND024 LND013 LND020 LND011 LND007 LND021 LND014 LND025 LND014 LND030 LND020 LND012 LND005 LND026 LND010 LND030 LND006 LND006 LND016 LND003 LND024 LND015 LND008 LND016 LND009 LND003 LND029 LND010 LND009 LND018 LND019 LND001 LND001 LND029 LND028 LND022 LND002 LND025 LND026 LND004 LND005 LND019 LND021 LND007 LND012 LND015 LND027 LND017 LND011 LND022 1 A VST_P DWN_P PCG_P HST_P WIDE_P HCK2_P HCK1_P VP_P RGT_P COM_P VCK_P VST_P RGT_P VP_P XSTBY_P DWN_P PCG_P HST_P HCK2_P HCK1_P WIDE_P REF_P VR_P VG_P VB_P EN_P VG_P VR_P VB_P XSTBY_P EN_P VCK_P REF_P COM_P VST WIDE VDD PANEL_REV TP_R G TP_BOT HCK1 RGT CS REG_GND TEST1 HST TEST2 N.C DWN REG_GND PCG N.C COM PANEL_REV EN R VSSG PSIG 2ND_ZOOM(T) VSS TP_TOP REG_GND B REG_GND N.C. N.C. VCK 2ND_S/S_SW HCK2 N.C. REF TP_L N.C 2ND_ZOOM(W) XSTBY BL_H3 PCG VST HST REF EP_2.8V(N.C.) HCK1 BL_H2 COM XSTBY REG_GND HCK2 REG_GND KEY_AD1 WIDE RGT REG_GND TP_SEL1 EN DWN TP_X TP_Y PSIG VCK D_2.8V PANEL_VB PANEL_VR PANEL_VG VDD_P BL_H1 Q9601, Q9602 TOUCH PANEL I/F D9603, D9604, D9605 (BACKLIGHT) LCD COLOR LCD901 UNIT (1/2) 2.5 INCH TOUCH with PANEL TOUCH with PANEL (2/2) LCD LCD901 UNIT XX MARK:NO MOUNT LCD, LCD BACKLIGHT PD-281 BOARD 2ND_ZOOM(W) 5 2ND_S/S_SW REG_GND REG_GND 2 (SB9000) 6 4 CONTROL KEY BLOCK N.C. 2ND_ZOOM(T) (ZOOM) T 3 REC START/STOP 1 W 4 6 (PANEL REVERSE) PANEL_REV 5 REG_GND REG_GND PANEL_REV 2 3 1 N.C. FLEXIBLE BOARD N.C. PANEL REVERSE DETECT HCK2 RGT XSTBY PANEL_VR WIDE VCK HCK1 PANEL_VG VST EP_2.8V(N.C.) PCG PSIG PANEL_VR REG_GND HST REG_GND REF DWN DWN PSIG VDD_P REF EN PANEL_VB BL_H2 PANEL_VB HCK2 COM BL_H2 REG_GND D_2.8V D_2.8V TP_X VDD_P HST REG_GND TP_SEL1 EN TP_Y BL_H3 REG_GND REG_GND XSTBY KEY_AD1 WIDE KEY_AD1 BL_H3 PCG VCK TP_SEL1 TP_X RGT TP_Y BL_H1 EP_2.8V(N.C.) BL_H1 VST PANEL_VG HCK1 COM 9 25 29 16 26 13 10 8 20 15 27 28 17 18 1 6 22 12 30 7 3 19 14 5 21 4 23 24 11 2 12 18 23 14 30 10 29 28 1 16 6 3 17 25 4 9 20 21 8 7 19 13 22 2 26 15 5 11 27 24 FP-380 FLEXIBLE BOARD CN9302 (6/12) VC-416 of LEVEL3 PAGE 4-11 FP-386 D F B 13 E 5 J 3 H C 6 12 2 9 14 11 7 G 4 10 I 05 K 8

supplied, but this is included in CR-061 complete board. :DCR-HC35E LND001 CN002 42P 1 3 5 7 9 11 13 19 21 23 25 27 29 31 33 35 37 39 41 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 43 44 36P CN003 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 1 A STATIC_GND USB_D- NTPA ACV_GND S_Y_I/O AUDIO_L_I/O AUDIO_R_I/O ACV_GND ACV_GND USB_DET NTPB TPB LANC_DC REG_GND ACV_UNREG ACV_GND BATT/XEXT ACV_UNREG REG_GND MULTI_JACK_IN VIDEO_I/O ACV_GND ACV_GND ACV_UNREG REG_GND REG_GND S_C_I/O USB_D+ ACV_UNREG LANC_SIG REG_GND TPA ACV_UNREG ACV_UNREG AUDIO_R_I/O REG_GND LANC_DC BATT/XEXT ACV_GND N.C. N.C.(S_JACK_IN) AUDIO_L_I/O ACV_GND TPB ACV_GND VIDEO_I/O REG_GND S_C_I/O LANC_SIG NTPA S_Y_I/O NTPB ACV_UNREG N.C.(XLANC_JACK_IN) ACV_UNREG XCRADLE_IN MULTI_JACK_IN ACV_GND REG_GND USB_D+ ACV_UNREG USB_D- N.C. ACV_UNREG REG_GND TPA USB_GND USB_GND N.C.(USB_ID) USB_GND USB_DET/VBUS N.C. N.C. N.C. USB_DET/VBUS USB_GND N.C. ACV_GND ACV_UNREG 15 17 TO CLADLE UNIT (MULTI CONNECTOR) (12/12) THROUGH THE PAGE 4-17 CN1006 of LEVEL3 VC-416 CABLE (FFC-060) FLEXIBLE FLAT 05 8 D F B XX MARK:NO MOUNT E CR-061 BOARD 5 3 CRADLE TERMINAL H C 6 2 9 7 G 4 10 330p C001 330p C002

SE601 XX 1 3 4 2 XX R608 XX C608 XX C611 XX C610 XX R609 XX R610 SE602 XX 1 3 4 2 XX R619 XX R611 RB601 XX 1 2 3 4 5 6 7 8 XX IC602 1 PASS 2 OUT1 3 AM1 4 Vref1 5 HO1 6 HI1 7 LO1 8 LIA1 9 LIB1 10 GND 11 LIB2 12 LIA2 13 LO2 14 HI2 15 HO2 16 Vref2 17 AM2 18 OUT2 19 CRST 20 VCC XX R617 XX L601 XX C604 XX R622 XX C602 XX R607 XX R606 XX LF601 1 2 3 4 XX R616 XX R618 XX C612 1 2 3 4 XX C613 1 2 3 4 XX C615 C614 XX Q601 XX XX D609 OUT GND GND Vref OUT Vref Vcc Vcc XX D601 5 4 3 2 1 NO MARK:REC/PB MODE Note: CRADLE model is no connection. CRADLE model:DCR-HC35E NON CRADLE model:DCR-HC23E/HC24E/HC26/HC26E Note: IC601 is not included in SI-051 complete board. 2.8 2.8 DCR-HC24E/HC35E (Note) (Note) (Note) (Note) (Note) (Note) (Note) DCR-HC23E /HC24E DCR-HC26 /HC26E NON CRADLE model CN603 5P VCC 1 D- 2 D+ 3 ID 4 GND 5 6 7 D602 MAZB068H0LS0 1 2 6 5 4 3 IC601 RPM7640-V17 1 OUT 2 GND 3 Vcc LND602 CHASSIS_GND BT601 FB601 FB602 REG_GND 36P CN605 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 CN601 10P 1 AUDIO L 2 LANC_SIG 3 S GND 4 LANC_DC 5 S-C 6 AUDIO R 7 JACK AD 8 VIDEO/AUDIO GND 9 VIDEO IN/OUT 10 S-Y 11 12 13 14 CN604 4P 1 NTPB 2 TPB 3 NTPA 4 TPA 5 6 SOL601 LND601 CHASSIS_GND 4P CN602 1 INT_MIC_L 2 INT_MIC_GND 3 INT_MIC_R 4 INT_MIC_GND 1/10W 22 R624 1/10W 22 R623 F601 (0.2A/32V) F602 (0.2A/32V) D608 1SS357(T3SONY1) RB602 10k 1 2 3 4 5 6 7 8 CL-330IRS-X-TU D606 DF3A6.8FV(TH3SONY) D603 3 2 1 LF602 1 3 4 2 LF603 1 3 4 2 470p C617 470p C616 1 A NTPB USB_D- TPB USB_D+ NTPA USB_DET TPA USB_D+ TPA NTPA TPB USB_D- S_Y_I/O S_C_I/O MULTI_JACK_IN VIDEO_I/O LANC_DC LANC_SIG AUDIO_R_I/O AUDIO_L_I/O MULTI_JACK_IN AUDIO_L_I/O S_C_I/O AUDIO_R_I/O S_Y_I/O LANC_DC LANC_SIG VIDEO_I/O NTPB USB_DET USB INT_MIC_GND REG_GND INT_MIC_L AUDIO_L_I/O AUDIO_R_I/O VST_C_RESET(N.C.) REG_GND NS_LED_K VIDEO_I/O D_2.8V A_2.8V(N.C.) INT_MIC_R LANC_DC LANC_SIG USB_D+ REG_GND TPA YAW_AD(N.C.) S_Y_I/O MULTI_JACK_IN USB_DET INT_MIC_GND PITCH_AD(N.C.) S_C_I/O USB_D- SIRCS_SIG REG_GND REG_GND NTPA TPB NTPB SYSTEM_AD REG_GND REG_GND LI_3V REG_GND PAGE 4-17 VC-416 CN1004 CABLE (FFC-060) of LEVEL3 FLEXIBLE FLAT (12/12) THROUGH THE LITHIUM BATTERY R MICROPHONE L MIC901 05 8 D F B XX MARK:NO MOUNT E SI-051 BOARD 5 3 AV/DV/USB CONNECTOR H C 6 2 9 11 7 G 4 10 A/V OUT IR EMITTER /NIGHTSHOT IC601 REMOTE SENSOR DV DV OUT (USB) 12

5 3 LB-121 BOARD 6 2 C EVF, EVF BACKLIGHT 7 4 E Note: BH001 and J001 are not included in FP-381 flexible board. LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND010 LND009 LND011 LND015 LND014 LND012 LND016 LND013 LND020 LND017 LND019 LND022 LND023 LND024 LND018 J001 LND008 LND021 1 A ACV_UNREG BATT_UNREG ACV_GND BATT_SIG BATT/XEXT BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG ACV_UNREG ACV_UNREG ACV_UNREG ACV_UNREG ACV_GND ACV_GND ACV_GND BATT_GND BATT_GND BATT_GND BATT_GND BATT_GND ACV_GND N.C. 22 16 11 8 17 24 15 2 6 18 1 23 12 3 7 14 4 5 20 19 10 9 21 13 DC IN D B DC IN E 3 FP-381 FLEXIBLE BOARD C 2 4 05 (BATTERY TERMINAL) 5 (10/12) VC-416 of LEVEL3 CN2001 PAGE 4-15 N.C. C BH001

MIC902 4 PIN CONNECTOR Q902 PT4850FJE00F TAPE TOP SENSOR S903 (MODE SWITCH) FP-032 FLEXIBLE BOARD FP-228 FLEXIBLE BOARD DEW SENSOR D901 GL453SE0000F (TAPE LED) S902 (REC PROOF) FP-031 FLEXIBLE BOARD M902 LOADING MOTOR G Vcc - + G - Vcc + H902 HW-105A-CDE-T T REEL SENSOR H901 HW-105A-CDE-T S REEL SENSOR 05 Q901 PT4850FJE00F TAPE END SENSOR LM_LOAD LM_LOAD LM_UNLOAD LM_UNLOAD DEW- DEW+ XMODE_SW_A XMODE_SW_B XMODE_SW_C SW_COM XREC_PROOF CHIME_VDD CHIME_SDA CHIME_SCK MIC/REC_SW_GND TAPE_TOP XCCDOWN_SW Cin_GND TREEL- TREEL+ HALL_VCC SREEL+ SREEL- HALL_GND TAPE_LED_K TAPE_LED_A TOP/END_GND TAPE_END 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 NC 28 29 PAGE 4-13 VC-416 (8/12) CN1007 of LEVEL3 1 A D F B E 5 3 8 C 6 2 9 7 4 S901 (CC DOWN) DEW- DEW+ 1 2 MODE_SW_A MODE_SW_A 1 2 MODE_SW_A SW_COM/SW_GND 3 4 DEW- DEW+ 1 2 MODE_SW_A MODE_SW_A 1 2 MODE_SW_A SW_COM/SW_GND 3 4 M

so that PRINTED WIRING BOARD is omitted. LND002 LND001 LND003 LND005 LND004 LND006 S005 1 3 2 4 S002 1 3 2 4 LND009 R002 5400 S004 1 3 2 4 S001 LND007 LND008 D001 1 A S003 1 3 2 4 20k R003 12.2k R001 CHASSIS_GND KEY_AD3 N.C. BATT_INFO XRESET D_2.8V REG_GND EASY BACK LIGHT XCHARGE_LED CHG 8 2 6 1 2 1 3 7 4 5 PANEL OPEN/CLOSE BATT INFO DISP/ D B 5 3 CONTROL KEY BLOCK (CF17000) C 2 4 05 of LEVEL3 (9/12) CN1017 VC-416 PAGE 4-14 of LEVEL3 (5/12) CN1001 VC-416 PAGE 4-10 RESET SP901 SPEAKER CHARGE_LED_VDD SP+ SP- XX D001 CONTROL KEY BLOCK (SS17000) is replaced as block, so that PRINTED WIRING BOARD is omitted. D003 D002 S001 1 3 2 4 S002 1 3 2 4 S003 1 3 2 4 S004 1 3 2 4 LND014 LND011 LND012 LND009 LND008 LND010 LND007 LND005 LND004 LND001 LND006 LND002 LND003 50k RV001 R001 20k 17.6k R002 LND013 1 A REG_GND XPOWER_SW XMODE_SW REG_GND D_2.8V MODE_LED_VDD XCAM_LED ZOOM_VR PLAY/EDIT (EJECT) START/STOP KEY_AD2(PHOTO) REG_GND KEY_AD5(SS) XMODE_SW XPOWER_SW XEJECT_SW REG_GND 13 9 1 14 12 5 2 10 8 6 11 7 4 3 W T (ZOOM) POWER OFF(CHG) MODE ON PHOTO (PHOTO REC) (PHOTO FREEZE) C 8 CONTROL KEY BLOCK (SS17000) D 5 7 E 3 B 2 05 F 4 6 CN1012 PAGE 4-14 VC-416 of LEVEL3 (9/12) N.C.(XVTR_LED) XVTR_LED(XMEM_LED) REC CAMERA

CD-631 BOARD PD-281 BOARD (SIDE B) PD-281 BOARD (SIDE A) CR-061 BOARD FP-386 FLEXIBLE BOARD LB-121 BOARD SI-051 BOARD FP-381 FLEXIBLE BOARD FP-031, FP-032, FP-228 FLEXIBLE BOARD MOUNTED PARTS LOCATION COMMON NOTE FOR PRINTED WIRING BOARDS

4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS • : Uses unleaded solder. • : Circuit board : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers’ patterns are not indicated) • Through hole is omitted. • There are a few cases that the part printed on diagram isn’t mounted in this model. • C: panel designation THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS 2 1 3 2 1 3 2 1 3 3 4 5 2 1 1 2 3 6 5 4 E B C 3 1 5 2 4 6 1 2 3 6 5 4 3 1 5 2 4 6 1 2 3 5 4 4 3 1 2 3 1 2 4 5 5 3 4 1 2 1 4 2 3 4 6 2 5 3 1 1 2 4 3 1 4 2 3 • Chip parts. Transistor Diode

: Uses unleaded solder. 14 8 7 1 IC101 11 05 CD-631 BOARD (SIDE A) 1-868-293- Note: IC101 is not included in CD-631 complete board. 1 14 CL101 CL102 CL103 Q101 L101 R101 B E C CN101 C101 C102 C103 C104 C105 11 05 CD-631 BOARD (SIDE B) 1-868-293-

Pages from 4-28 to 4-29 are not shown.

: Uses unleaded solder. 1 30 1 1 3 1 3 6 4 6 4 1 3 6 4 6 1 6 1 6 1 24 C B E CN9601 CN9602 CN9603 CN9604 CN9605 LND901 C9601 C9602 C9603 C9604 Q9601 C9605 Q9602 C9606 Q9603 D9601 D9602 R9601 R9602 D9606 R9603 D9607 R9604 D9608 R9606 R9607 R9608 R9609 R9610 R9611 R9605 11 C B A 1 2 3 4 5 05 PD-281 BOARD (SIDE A) 1-868-305- D

: Uses unleaded solder. D9603 D9604 D9605 A K A K A K (BACKLIGHT) (BACKLIGHT) (BACKLIGHT) 11 C B A 1 2 3 4 5 05 PD-281 BOARD (SIDE B) 1-868-305- D

FP-386 (1 layer), CR-061 (2 layers), SI-051 (2 layers) : Uses unleaded solder. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. FP-3 8 6 >PI< F X 1 S101 (PANEL REVERSE) S101 FP-386 FLEXIBLE BOARD 1-867-795- 11 05 LND101 1 6 LND103 LND104 LND106 LND001 41 1 1 3 6 4 1 3 6 4 1 3 6 4 1 3 6 4 5 15 25 35 42 2 10 20 30 40 44 43 1 36 CN002 CN003 D001 D002 D003 D005 C002 C001 11 05 CR-061 BOARD 1-868-328- Note: CN002 (multi connector) is not supplied, but this is included in CR-061 complete board. 1 6 2 9 10 7 3 8 4 5 10 C B E R606 R607 R608 R609 R610 R611 R622 C602 C608 C610 D601 1 3 4 5 SE601 2 1 4 3 (PITCH) LND601 LND602 F601 F602 Q601 FB601 FB602 D606 IR EMITTER/ NIGHTSHOT CN601 A/V OUT 11 1 2 05 SI-051 BOARD (SIDE A) 1-868-300- A B C D E 1 4 2 36 1 35 1 20 10 11 R616 R617 R618 R619 CN602 CN605 R623 R624 C604 BT601 SOL601 C611 C612 C613 C614 C615 C616 C617 LF601 LF602 LF603 D602 D603 1 3 6 4 D608 D609 IC602 RB601 RB602 L601 1 4 3 1 2 7 2 8 3 4 1 2 3 4 1 2 2 4 1 3 2 4 1 3 1 2 3 SE602 2 1 4 3 (YAW) 1 7 2 8 11 12 13 14 1 2 4 5 7 6 1 2 3 4 5 6 1 3 CN601 Note: IC601 is not included in SI-051 complete board. CN603 IC601 11 1 2 05 SI-051 BOARD (SIDE B) 1-868-300- A B C D E DV OUT (USB) CN604 DV BT601 BATTERY, LITHIUM SECONDARY EXCEPT DCR-HC35E DCR-HC23E/HC24E DCR-HC26/HC26E

1-867-779- 11 12 05 LND001 1 LND024 LND023 LND022 LND021 LND020 LND019 LND017 LND016 LND015 LND014 LND013 LND012 LND011 LND010 LND009 LND008 LND007 LND005 LND004 LND003 LND002 24 BH001 BATTERY TERMINAL C Note: BH001 and J001 are not included in FP-381 flexible board. LB-121, FP-3 LB-121 (2 layers), FP-381 (1 layer) : Uses unleaded solder. 1 20 1 2 21 20 CN301 CN302 11 05 LB-121 BOARD (SIDE A) 1-868-308- R303 R304 A K C301 C302 C303 D301 D302 (BACKLIGHT) 11 05 LB-121 BOARD (SIDE B) 1-868-308-

FP-031 (1 layer), FP-032 (1 layer), FP-228 (1 layer) : Uses unleaded solder. DEW SENSOR M902 LOADING MOTOR S903 MODE SWITCH M (Dilect Solder) (Dilect Solder) 1 1 4 2 1-677-049- 11 1-867-810- 11 1-867-811- 11 12 29 1 FP-228 FLEXIBLE BOARD FP-032 FLEXIBLE BOARD FP-031 FLEXIBLE BOARD S902 (REC PROOF) S901 (CC DOWN) D901 (TAPE LED) H902 T REEL SENSOR H901 S REEL SENSOR MIC902 Q902 TAPE TOP SENSOR 4 PIN CONNECTOR Q901 TAPE END SENSOR GND VCC - + GND VCC - + 05

Page 4-35 to 4-36 are not shown.

* mark : side B 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS PD-281, SI-051 PD-281 BOARD C9603 A-4 C9605 B-4 C9606 C-4 CN9601 A-2 CN9602 B-4 CN9603 B-2 CN9604 A-4 CN9605 C-5 D9602 B-4 * D9603 B-5 * D9604 C-5 * D9605 A-5 Q9601 A-4 Q9602 A-4 R9602 A-3 R9603 A-3 R9604 B-3 R9607 B-4 * BT601 B-2 * C616 D-1 * C617 D-1 CN601 C-1 * CN603 A-1 * CN604 B-1 * CN605 D-2 * D602 D-1 * D603 D-1 D606 B-1 * D608 B-1 F601 B-1 F602 B-1 FB601 D-1 FB602 D-1 * IC601 C-2 * LF602 C-1 * LF603 C-1 * R623 B-2 * R624 B-1 * RB602 B-1 SI-051 BOARD 4-4. MOUNTED PARTS LOCATION

Link Link OVERALL ASSEMBLY FRONT PANEL BLOCK CABINET (R) BLOCK MAIN BLOCK-1 LENS BLOCK EVF BLOCK MECHANISM DECK SECTION ELECTRICAL PARTS LIST ELECTRICAL PARTS LIST EXPLODED VIEWS EXPLODED VIEWS ACCESSORIES ACCESSORIES NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown. LS/MECHANICHAL CHASSIS BLOCK ASSEMBLY-1 A B C D E F H I FP-031 FLEXIBLE BOARD CR-061 BOARD CD-631 BOARD FP-380 FLEXIBLE BOARD FP-228 FLEXIBLE BOARD FP-032 FLEXIBLE BOARD FP-381 FLEXIBLE BOARD FP-386 FLEXIBLE BOARD LB-121 BOARD SI-051 BOARD PD-281 BOARD J G E C J J D C F B C G LS/MECHANICHAL CHASSIS BLOCK ASSEMBLY-2 J MAIN BLIOCK-2

5. REPAIR PARTS LIST DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • CAPACITORS: uF: µF • COILS uH: µH • RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable • SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , uPC... , µPC... , uPD..., µPD... When indicating parts by reference number, please include the board name. • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 5-1-1. OVERALL ASSEMBLY Ref. No. Part No. Description Ref. No. Part No. Description 1 X-2108-030-1 CABINET (172) ASSY, NS 2 2-664-983-11 CABINET (UPPER (172)) (HC24E/HC26/HC26E/HC35E) 2 2-664-983-21 CABINET (UPPER (172)) (HC23E) #2 2-635-562-31 SCREW (M1.7) (Black) #10 2-599-475-31 SCREW (M1.7) (Silver) #14 2-599-475-11 SCREW (M1.7) (Silver) 5-1. EXPLODED VIEWS #2 #2 #10 #10 #10 #2 #2 #14 #14 #14 1 2 Front Panel Block (See page 5-3.) Cabinet (R) Block (See page 5-4.) Main Block-1 (See page 5-5.) DISASSEMBLY HARDWARE LIST

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 5-1-2. FRONT PANEL BLOCK Ref. No. Part No. Description Ref. No. Part No. Description 51 X-2108-154-1 PANEL (170) ASSY, F (HC23E) 51 X-2108-155-1 PANEL (17R) ASSY, F (HC24E) 51 X-2108-156-1 PANEL (171) ASSY, F (HC26/HC26E) 51 X-2108-157-1 PANEL (17C) ASSY, F (HC35E) 52 2-664-940-01 SCREW (172), FILTER 53 2-664-986-01 COVER, JACK * 54 2-664-946-01 RETAINER, MICROPHONE 55 A-1153-836-A SI-051 BOARD, COMPLETE (HC23E/HC24E/HC26/HC26E) 55 A-1153-837-A SI-051 BOARD, COMPLETE (HC35E) ns: not supplied * 56 2-672-995-01 SHEET (F) 57 3-941-343-01 TAPE (A) 0* BT601 1-756-640-11 BATTERY, LITHIUM SECONDARY * IC601 6-600-505-01 IC RPM7640-V17 (HC24E/HC35E) (Note) MIC901 1-542-513-21 MICROPHONE #8 3-078-890-01 SCREW, TAPPING (Silver) #12 3-080-204-21 SCREW, TAPPING, P2 (Black) CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Refer to page 5-1 for mark 0. SI-051 #8 #12 #12 #12 IC601 (Note) BT601 ns HC24E/HC35E 57 51 52 53 56 54 55 ! : BT601 (BATTERY, LITHIUM SECONDARY) Board on the mount position. (See page 4-32.) MIC901 Note: IC601 is not included in SI-051 complete board. HARDWARE LIST

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 Ref. No. Part No. Description Ref. No. Part No. Description 101 2-664-728-11 CABINET (C), P (HC26/HC26E) 101 2-664-728-41 CABINET (C), P (HC23E) 101 2-664-728-51 CABINET (C), P (HC24E) 101 2-664-728-61 CABINET (C), P (HC35E) 102 3-941-343-01 TAPE (A) 103 A-1153-839-A PD-281 BOARD, COMPLETE * 104 1-867-778-11 FP-380 FLEXIBLE BOARD (Note) 105 2-664-737-01 COVER (C), HINGE 106 X-2067-431-1 HINGE ASSY 107 2-664-738-01 COVER (M), HINGE 108 2-664-735-01 CUSHION (172), TP 109 A-1153-842-A FP-386 FLEXIBLE BOARD, COMPLETE 5-1-3. CABINET (R) BLOCK 110 X-2103-699-1 CABINET (M (172)) ASSY, P 111 1-479-063-21 KEY BLOCK, CONTROL (SB9000) 112 X-2103-698-1 CABINET (R (171)) ASSY 113 A-1153-903-A LIGHT GUIDE BLOCK (2.5) 114 1-479-506-11 KEY BLOCK, CONTROL (CF17000) LCD901 A-1149-654-A TP BLOCK ASSY (25STMG06) * SP901 1-825-260-31 K016NA503-12 #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red) #10 2-599-475-31 SCREW (M1.7) (Silver) #12 3-080-204-21 SCREW, TAPPING, P2 (Black) #13 3-085-397-01 SCREW (Silver) Note: Be sure read “HELP” when you install the FP- 380 flexible board. DISASSEMBLY HARDWARE LIST PD-281 #12 #12 #12 LCD901 #13 #10 #12 #3 ns 102 102 104 (Note) 101 103 105 107 108 109 110 111 112 114 ns 106 113 ns ns ns SP901 ns: not supplied

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 5-1-4. MAIN BLOCK-1 Ref. No. Part No. Description Ref. No. Part No. Description 151 X-2108-032-1 BOTTOM (172) ASSY, CABINET (HC23E/HC24E/HC26/HC26E) 151 X-2108-033-1 BOTTOM (173) ASSY, CABINET (HC35E) * 152 1-867-779-11 FP-381 FLEXIBLE BOARD 153 X-2108-652-1 PANEL (172) ASSY, BT 154 2-664-984-01 COVER, DC (IN) 155 2-664-985-01 LID, CPC ns: not supplied BH001 1-780-064-21 BATTERY TERMINAL BOARD (Note) J001 1-815-792-11 CONNECTOR, DC-IN (7.2V) (Note) #2 2-635-562-31 SCREW (M1.7) (Black) #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red) #11 3-078-890-11 SCREW, TAPPING (Silver) DISASSEMBLY HARDWARE LIST #3 #3 #2 #2 #2 #11 BH001 (Note) J001 (Note) ns 151 152 153 154 155 Lens Block (See page 5-6.) EVF Block (See page 5-7.) HC35E Main Block-2 (See page 5-8.) Note: BH001 and J001 are not included in FP-381 flexible board.

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 Ref. No. Part No. Description Ref. No. Part No. Description 201 1-788-332-11 OPTICS UNIT (EG03B) 201 8-848-804-01 LSV-1070B * 202 2-664-981-01 FRAME (172), LENS 203 1-788-242-11 OPTICAL FILTER BLOCK 204 2-318-138-01 RUBBER, SEAL 1070 * 205 1-830-778-11 CABLE, FLEXIBLE FLAT (FFC-063) 5-1-5. LENS BLOCK 206 A-1153-810-A CD-631 BOARD, COMPLETE IC101 8-753-244-70 ICX610NKF-13 (CCD IMAGER) (HC26) (Note 1, 2) IC101 8-753-244-71 ICX611NKF-13 (CCD IMAGER) (HC23E/HC24E/HC26E/HC35E) (Note 1, 2) #12 3-080-204-21 SCREW, TAPPING, P2 (Black) #13 3-085-397-01 SCREW (Silver) HARDWARE LIST Note 1: IC101 is not included in CD-631 complete board. Note 2: Be sure to read “Precuations for Replacement of Imager” on page 4-3 when changing the imager. CD-631 #12 IC101 (Note1, 2) #13 201 202 203 204 205 206

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 5-1-6. EVF BLOCK Ref. No. Part No. Description Ref. No. Part No. Description 251 A-1153-834-A LB-121 BOARD, COMPLETE 252 2-664-672-01 GUIDE, LAMP * 253 2-638-819-01 CUSHION, LCD * 254 2-638-818-01 ILLUMINATOR * 255 2-638-816-01 PLATE (TFT), DEFLECTION 256 2-664-671-01 SPACER, LCD 257 3-941-343-01 TAPE (A) * 258 1-867-777-11 FP-379 FLEXIBLE BOARD * 259 2-664-670-01 CABINET, INNER * 260 2-638-813-01 PLATE (CF), DEFLECTION * 261 2-664-669-01 FRAME (172), FIXED 262 X-2103-696-1 VF (172) ASSY 263 X-2103-695-1 EYE CUP ASSY LCD902 8-753-245-09 LCX059CKK-1 #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red) #12 3-080-204-21 SCREW, TAPPING, P2 (Black) HARDWARE LIST #12 #3 LCD902 251 257 253 258 259 254 255 256 252 260 262 261 263

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 Ref. No. Part No. Description Ref. No. Part No. Description 301 2-664-982-01 SCREW, TRIPOD * 302 2-664-976-01 FRAME (171), BOTTOM (HC23E/HC24E/HC26/HC26E) * 302 2-664-977-01 FRAME (172), BOTTOM (HC35E) 303 1-479-507-11 KEY BLOCK, CONTROL (SS17000) 304 A-1154-404-A VC-416 BOARD, COMPLETE (SERVICE) (HC23E/HC24E/HC26/HC26E) 304 A-1154-405-A VC-416 BOARD, COMPLETE (SERVICE) (HC35E) 5-1-7. MAIN BLOCK-2 * 305 1-830-775-11 CABLE, FLEXIBLE FLAT (FFC-060) 306 A-1153-808-A CR-061 BOARD, COMPLETE (HC35E) 308 2-659-500-01 LABEL, FUSE REPLACEMENT CAUTION (US, CND) #2 2-635-562-31 SCREW (M1.7) (Black) #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red) #15 3-062-214-01 SCREW (M1.4X1.5) (Silver) ns: not supplied VC-416 CR-061 ns #3 #3 #2 301 302 303 304 305 308 306 305 #15 Mechanism Deck Section (See page 5-9.) HC35E US, CND DISASSEMBLY HARDWARE LIST

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 5-1-8. MECHANISM DECK SECTION ns : not supplied M901 LS chassis block assembly (See page 5-10) 708 703 704 701 ns 714 715 712 713 711 705 705 705 709 710 707 702 706 Ref. No. Part No. Description Ref. No. Part No. Description 701 X-2024-478-1 PENDULUM ASSY 702 2-342-917-02 LED BASE 703 7-627-850-77 SCREW, PRECISION +P 1.4X1.8 704 3-079-366-11 RELEASE, REEL LOCK 705 3-703-816-08 SCREW (M1.4X1.4), SPECIAL HEAD 706 X-2024-450-1 COMPARTMENT ASSY, CASSETTE 707 2-342-926-01 SPRING (ARM S), TENSION COIL 708 2-546-417-01 SCREW (M1.4) 709 2-342-933-01 PLATE, TOP 710 2-342-927-01 SPRING (ARM T), TENSION COIL 711 2-541-585-01 SHEET, FLEXIBLE ADHESIVE 712 2-342-918-01 TG6 CATCHER 713 A-1080-997-A MD (N100) SUB ASSY A 714 3-703-816-13 SCREW (M1.4X2.0), SPECIAL HEAD 715 3-315-414-31 WASHER M901 A-1137-055-A DRUM (DEH-33D-R) (SERVICE)

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 5-1-9. LS/MECHANICAL CHASSIS BLOCK ASSEMBLY-1 ns : not supplied ns 755 768 755 756 757 759 760 761 764 765 762 763 768 768 769 770 771 758 ns 752 753 754 751 766 767 LS / Mechanical chassis block assembly-2 (See page 5-11) Note: These two screws are the fixing screws of the LS cam plate. These two fixing screws are used for adjsting the LS cam plate position. (refar to 4-2. LS cam adjustment of DV mechanical adjustment manual IX) 772 (Note) 772 (Note) Ref. No. Part No. Description Ref. No. Part No. Description 751 2-342-759-01 SPRING, RVS BRAKE 752 A-1083-005-A BLOCK ASSY, RVS BRAKE 753 2-342-731-01 POSITIONING, S 754 A-1083-006-A BLOCK ASSY, S BRAKE 755 3-075-097-11 SCREW (M1.4X1.4), SPECIAL HEAD 756 X-2024-473-1 TABLE ASSY, S REEL 757 A-1083-007-B BLOCKASSY, TENSION REGULATOR 758 2-342-705-01 GEAR (T), GL 759 2-342-902-01 SPRING, TENSION REGULATOR 760 X-2024-474-1 TABLE ASSY, T REEL 761 X-2024-476-1 ARM ASSY, PINCH 762 2-342-906-01 SPRING (PINCH RETURN), TORSION 763 2-342-626-01 SPRING (RETURN TG6), EXTENSION 764 A-1083-002-A BLOCK ASSY, TG6 765 X-2024-468-1 ARM ASSY (S), GL 766 X-2024-465-1 COASTER (S) ASSY 767 2-342-612-01 RAIL 768 3-703-816-13 SCREW (M1.4X2.0), SPECIAL HEAD 769 X-2024-466-1 COASTER (T) ASSY 770 X-2024-469-1 ARM (T) ASSY, GL 771 2-342-716-01 SPRING (T), TORSION COIL 772 3-703-816-08 SCREW (M1.4X1.4), SPECIAL HEAD (for adjustment)

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 ns : not supplied 5-1-10. LS/MECHANICAL CHASSIS BLOCK ASSEMBLY-2 801 802 803 804 804 810 812 813 814 815 815 816 817 818 811 806 807 808 809 ns ns ns H901 D901 Q902 S901 M902 Q901 MIC902 H902 819 820 821 FP-031 (Note 1) FP-031 (Note 1) FP-032 (Note 1, 2) Note1:The FP-031 and FP-032 are supplied as the assembled part of the MD (N100) sub ass'y A by attaching them with the adhesive agent. These parts are not separately supplied because assembling of these parts requires high accuracy. Note2:The mode switch (S903) function works when the contactor of the FP-032 contacts with the bottom surface of wiper of the mode gear ass'y. (Note2) Ref. No. Part No. Description Ref. No. Part No. Description 801 2-342-624-01 SPRING (PINCH LIMITTER), EXTENSION 802 X-2024-463-1 SLIDER ASSY, MODE 803 X-2024-462-1 GEAR ASSY, CAM 804 3-075-097-11 SCREW (M1.4X1.4), SPECIAL HEAD 806 2-342-621-01 GEAR, RELAY 807 3-315-414-31 WASHER 808 2-342-620-01 GEAR, CONVERSION 809 3-084-377-01 HEAD (SCREW M1.2) 810 X-2024-460-1 BASE ASSY, CAM 811 X-2024-461-1 GEAR ASSY, MODE 812 2-342-615-01 GEAR, NO.2 813 2-342-691-01 GEAR, NO.1 814 2-342-688-01 MOTOR HOLDER 815 3-895-822-71 SCREW (M1.2X2), SPECIAL, 0 816 2-342-689-01 WORM SHAFT (2J) 817 2-342-690-01 BASE, MOTOR HOLDER 818 1-677-049-11 FP-228 FLEXIBLE BOARD (DEW SENSOR) 819 2-342-686-01 COVER, CAPSTAN 820 2-541-984-01 MIC COVER 821 3-703-816-13 SCREW (M1.4X2.0), SPECIAL HEAD D901 6-500-652-01 DIODE GL453SE0000F (TAPE LED) H901 8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T (S REEL) H902 8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T (T REEL) M902 X-2024-464-1 MOTOR ASSY (LOADING) MIC902 1-818-576-11 PIN, CONNECTOR (WITH DETECTION SWITCH) Q901 6-550-672-01 TRANSISTOR PT4850FJE00F (TAPE END) Q902 6-550-672-01 TRANSISTOR PT4850FJE00F (TAPE TOP) S901 1-786-448-22 SWITCH, PUSH (1 KEY) (CC DOWN)

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 CD-631 CR-061 FP-031 FP-032 FP-228 FP-380 FP-381 FP-386 A-1153-810-A CD-631 BOARD, COMPLETE ********************** (IC101 is not included in CD-631 complete board.) < CAPACITOR > C101 1-124-779-00 ELECT CHIP 10uF 20% 16V C102 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V C104 1-124-779-00 ELECT CHIP 10uF 20% 16V < CONNECTOR > CN101 1-766-344-51 CONNECTOR, FFC/FPC 14P < IC > IC101 8-753-244-70 ICX610NKF-13 (CCD IMAGER) (HC26) (Note) IC101 8-753-244-71 ICX611NKF-13 (CCD IMAGER) (HC23E/HC24E/HC26E/HC35E) (Note) < COIL > L101 1-400-588-11 INDUCTOR 10uH < TRANSISTOR > Q101 8-729-423-55 TRANSISTOR 2SC3931-D < RESISTOR > R101 1-218-959-11 RES-CHIP 3.3K 5% 1/16W A-1153-808-A CR-061 BOARD, COMPLETE (HC35E) ********************** (CN002 (multi connector) is not supplied, but this is included in CR-061 complete board.) < CAPACITOR > C001 1-164-934-11 CERAMIC CHIP 330PF 10% 50V C002 1-164-934-11 CERAMIC CHIP 330PF 10% 50V < CONNECTOR > CN002 (Not supplied) CONNECTOR, MULTIPLE (SOCKET) CN003 1-766-613-51 CONNECTOR, FFC/FPC 36P (Not supplied) FP-031 FLEXIBLE BOARD ******************** (This flexible board is included in MD (N100) SUB ASSY A (A-1080-997-A).) < DIODE > D901 6-500-652-01 DIODE GL453SE0000F (TAPE LED) < HOLE ELEMENT > H901 8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T (S REEL) H902 8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T (T REEL) < CONNECTOR > MIC902 1-818-576-11 PIN, CONNECTOR (WITH DETECTION SWITCH) < TRANSISTOR > Q901 6-550-672-01 TRANSISTOR PT4850FJE00F (TAPE END) Q902 6-550-672-01 TRANSISTOR PT4850FJE00F (TAPE TOP) < SWITCH > S901 1-786-448-22 SWITCH, PUSH (1 KEY) (CC DOWN) (Not supplied) FP-032 FLEXIBLE BOARD ******************** (This flexible board with S903 is included in MD (N100) SUB ASSY A (A-1080-997-A).) 1-677-049-11 FP-228 FLEXIBLE BOARD (DEW SENSOR) ******************** * 1-867-778-11 FP-380 FLEXIBLE BOARD ******************** * 1-867-779-11 FP-381 FLEXIBLE BOARD ******************** (BH001 and J001 are not included in FP-381 flexible board.) < BATTERY TERMINAL > BH001 1-780-064-21 BATTERY TERMINAL BOARD < JACK > J001 1-815-792-11 CONNECTOR, DC-IN (7.2V) A-1153-842-A FP-386 FLEXIBLE BOARD, COMPLETE ****************************** < SWITCH > S101 1-786-180-31 SWITCH, PUSH (1KEY) (PANEL REVERSE) A-1153-834-A LB-121 BOARD, COMPLETE ********************** < CAPACITOR > C301 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C302 1-165-908-11 CERAMIC CHIP 1uF 10% 10V < CONNECTOR > * CN301 1-818-046-51 CONNECTOR, FFC/FPC 20P * CN302 1-817-560-51 CONNECTOR, FPC (ZIP) 21P < DIODE > D301 6-500-941-01 DIODE MAZS056008S0 * D302 6-501-325-01 DIODE NESW007T-T017 (BACKLIGHT) LB-121 Note: Be sure to read “Precautions for Replacement of Imager” on page 4-3 when changing the imager.

< RESISTOR > R304 1-218-989-11 RES-CHIP 1M 5% 1/16W A-1153-839-A PD-281 BOARD, COMPLETE ********************** < CAPACITOR > C9603 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V C9605 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C9606 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < CONNECTOR > * CN9601 1-817-513-51 CONNECTOR, FFC/FPC (ZIF) 30P * CN9602 1-818-069-51 CONNECTOR, FFC/FPC (ZIF) 6P CN9603 1-573-915-51 CONNECTOR, FFC/FPC (ZIF) 6P CN9604 1-573-915-51 CONNECTOR, FFC/FPC (ZIF) 6P CN9605 1-815-031-51 CONNECTOR, FFC/FPC (ZIF) 24P < DIODE > D9602 6-500-941-01 DIODE MAZS056008S0 * D9603 6-501-476-01 DIODE NSSW008CT-T071 (BACKLIGHT) * D9604 6-501-476-01 DIODE NSSW008CT-T071 (BACKLIGHT) * D9605 6-501-476-01 DIODE NSSW008CT-T071 (BACKLIGHT) < TRANSISTOR > Q9601 8-729-427-67 TRANSISTOR XP421F-TXE Q9602 8-729-427-37 TRANSISTOR XP411F-TXE < RESISTOR > R9602 1-218-954-11 RES-CHIP 1.2K 5% 1/16W R9603 1-218-955-11 RES-CHIP 1.5K 5% 1/16W R9604 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R9607 1-218-989-11 RES-CHIP 1M 5% 1/16W A-1153-836-A SI-051 BOARD, COMPLETE (HC23E/HC24E/HC26/HC26E) A-1153-837-A SI-051 BOARD, COMPLETE (HC35E) ********************** (IC601 is not included in SI-051 complete board.) < BATTERY > 0* BT601 1-756-640-11 BATTERY, LITHIUM SECONDARY < CAPACITOR > C616 1-164-935-11 CERAMIC CHIP 470PF 10% 50V C617 1-164-935-11 CERAMIC CHIP 470PF 10% 50V < CONNECTOR > CN601 1-815-794-21 CONNECTOR (MULTIPLE) (A/V OUT) CN602 1-778-507-21 PIN, CONNECTOR (PC BOARD) 4P CN603 1-794-962-11 CONNECTOR, SQUARE TYPE (USB 5P) (USB) (HC23E/HC24E/HC26/HC26E) CN604 1-794-276-11 CONNECTOR, SQUARE TYPE 4P (DV OUT: HC23E/HC24E) (DV: HC26/HC26E) CN605 1-818-074-51 CONNECTOR, FFC/FPC (ZIF) 36P < DIODE > D602 6-500-044-01 DIODE DF6A6.8FU (TE85R) D603 6-500-776-01 DIODE MAZW068H0LS0 D606 6-500-512-01 DIODE CL-330IRS-X-TU (IR EMITTER/NIGHTSHOT) D608 8-719-078-02 DIODE 1SS357 (T3SONY1) (HC23E/HC24E/HC26/HC26E) < FUSE > 0F601 1-576-897-21 FUSE (0.2A/32V) (HC23E/HC24E/HC26/HC26E) 0F602 1-576-897-21 FUSE (0.2A/32V) (HC23E/HC24E/HC26/HC26E) < FERRITE BEAD > FB601 1-414-760-21 BEAD, FERRITE (CHIP) (1608) FB602 1-414-760-21 BEAD, FERRITE (CHIP) (1608) < IC > * IC601 6-600-505-01 IC RPM7640-V17 (HC24E/HC35E) < LINE FILTER > LF602 1-400-633-21 COMMON MODE CHOKE COIL (HC23E/HC24E/HC26/HC26E) LF603 1-400-633-21 COMMON MODE CHOKE COIL (HC23E/HC24E/HC26/HC26E) < RESISTOR > R623 1-216-801-11 METAL CHIP 22 5% 1/10W R624 1-216-801-11 METAL CHIP 22 5% 1/10W < COMPOSITION CIRCUIT BLOCK > RB602 1-234-378-21 RES, NETWORK 10K (1005X4) (HC23E/HC24E/HC26/HC26E) CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Refer to page 5-1 for mark 0. Electrical parts list of the VC-416 board is not shown. Pages 5-14 to 5-18 are not shown.

Checking supplied accessories. Other accessories 2-659-811-11 MANUAL, INSTRUCTION (HC26) (ENGLISH)(US, CND, E) 2-659-811-21 MANUAL, INSTRUCTION (HC26) (FRENCH) (CND) 2-659-811-31 MANUAL, INSTRUCTION (HC26) (SPANISH) (E, AR) 2-659-811-51 MANUAL, INSTRUCTION (HC26) (TRADITIONAL CHINESE) (E) 2-659-811-61 MANUAL, INSTRUCTION (HC26) (KOREAN) (KR) 2-659-812-11 MANUAL, INSTRUCTION (HC23E/HC26E/HC35E) (ENGLISH) (AEP, UK, E, AUS, HK) 2-659-812-21 MANUAL, INSTRUCTION (HC23E/HC26E/HC35E) (FRENCH) (AEP) 2-659-812-31 MANUAL, INSTRUCTION (HC23E/HC24E/HC35E) (GERMAN) (AEP) 2-659-812-41 MANUAL, INSTRUCTION (HC23E/HC24E/HC35E) (DUTCH) (AEP) 2-659-812-51 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (SPANISH) (AEP) 2-659-812-61 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (PORTUGUESE) (AEP) 2-659-812-71 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (ITALIAN) (AEP) 2-659-812-81 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (GREEK) (AEP) 2-659-812-91 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (SWEDISH) (NE) 2-665-183-11 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (RUSSIAN) (NE) 2-665-183-21 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (DANISH) (NE) 2-665-183-31 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (FINNISH) (NE) 2-665-183-41 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (POLISH) (EE) 2-665-183-51 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (CZECH) (EE) 2-665-183-61 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (HUNGARIAN) (EE) 2-665-183-71 MANUAL, INSTRUCTION (HC23E/HC24E/HC26E/HC35E) (SLOVAK) (EE) 2-665-183-81 MANUAL, INSTRUCTION (HC26E) (ARABIC) (E) 2-665-183-91 MANUAL, INSTRUCTION (HC24E/HC26E/HC35E) (PERSIAN) (E) 2-665-184-11 MANUAL, INSTRUCTION (HC26E) (TRADITIONAL CHINESE) (HK) 2-665-184-21 MANUAL, INSTRUCTION (HC26E) (SIMPLIFIED CHINESE) (E) 2-665-184-31 MANUAL, INSTRUCTION (HC26E) (THAI) (E) 2-665-185-11 MANUAL, INSTRUCTION (HC26E) (SIMPLIFIED CHINESE) (CH) AC Adaptor (AC-L25A/L25B) 0 1-479-288-13 Power Cord 0 1-555-074-71 (AUS) 0 1-782-476-41 (CH) 0 1-783-374-22 (HK) 0 1-790-107-51 (US, CND) 0 1-823-150-21 (AEP, EE, NE) 0 1-824-910-31 (E: PAL) 0 1-830-518-31 (E: NTSC) 0 1-830-736-21 (UK) 0 1-832-115-11 (KR) Conversion (2P) Adaptor 0 1-569-007-12 (E: NTSC) Conversion (2P) Adaptor 0 1-569-008-12 (E: PAL, HK) Lens Cap X-2108-241-1 A/V Connection Cable 1-823-156-51 USB Cable 1-829-868-31 (HC24E/HC35E) CD-ROM "Picture Package Ver. 1.5.1" 2-666-755-01 Handycam Station (DCRA-C151) 1-819-870-11 (HC35E) Rechargeable Battery Pack NP-FP30 0 A-1082-950-A (US, CND) 0 A-1082-951-A (EXCEPT US, CND) Wireless Remote Commander RMT-830 1-477-898-71 (HC24E/HC35E) 21-pin Adaptor 1-770-783-21 (HC35E)

2-635-562-11 2.5 1.7 #10: M1.7 X 4.0 (Silver) 2-599-475-31 1.6 1.7 #6: M1.4 X 1.7 (Silver) 2-598-474-01 1.7 1.4 #7: M1.7 X 1.6 (Black) 7-627-552-18 #3: M1.7 X 2.5 (Red) 2-660-401-01 2.5 1.7 #2: M1.7 X 4.0 (Black) 2-635-562-31 4.0 1.7 4.0 1.7 #5: M1.7 X 3.5 (Black) 3-080-204-01 3.5 1.7 #4: M1.4 X 2.5 (Dark Silver) 3-348-998-81 2.5 1.4 #12: M1.7 X 5.0 (Black) 3-080-204-21 1.7 #9: M1.7 X 5.0 (Silver) 3-078-890-21 5.0 1.7 #14: M1.7 X 2.5 (Silver) 2-599-475-11 #13: M1.7 X 2.5 (Silver) 3-085-397-01 2.5 1.7 #11: M1.7 X 4.0 (Silver) 3-078-890-11 #8: M1.7 X 3.5 (Silver) 3-078-890-01 3.5 1.7 4.0 1.7 5.0 2.5 1.7 #15: M1.4 X 1.5 (Silver) 3-062-214-01 1.5 1.4 HARDWARE LIST

Printing a text 1. Click the Print button . 2. Specify a printer, print range, number of copies, and other op- tions, and then click [OK]. Application of printing: To set a range to be printed within a page, select the graphic selection tool and drag on the page to enclose a range to be printed, and then click the Print button. Finding a text 1. Click the Find button . 2. Enter a character string to be found into a text box, and click the [Find]. (Specify the find options as necessary) Application to the Service Manual: To execute “find” from current page toward the previous pages, select the check box “Find Backward” and then click the “Find”. 3. Open the find dialog box again, and click the [Find Again] and you can find the matched character strings displayed next. (Character strings entered previously are displayed as they are in the text box.) Application to the Service Manual: The parts on the drawing pages (block diagrams, circuit dia- grams, printed circuit boards) and parts list pages in a text can be found using this find function. For example, find a Ref. No. of IC on the block diagram, and click the [Find Again] continuously, so that you can move to the Ref. No. of IC on the circuit diagram or printed circuit board diagram succes- sively. Note: The find function may not be applied to the Service Manual depending on the date of issue. Switching a page • To move to the first page, click the . • To move to the last page, click the . • To move to the previous page, click the . • To move to the next page, click the . Reversing the screens displayed once • To reverse the previous screens (operation) one by one, click the . • To advance the reversed screens (operation) one by one, click the . Application to the Service Manual: This function allows you to go and back between circuit dia- gram and printed circuit board diagram, and accordingly it will be convenient for the voltage check. Moving with link 1. Select either palm tool , zoom tool , text selection tool , or graphic selection tool . 2. Place the pointer in the position in a text where the link exists (such as a button on cover and the table of contents page, or blue characters on the removal flowchart page or drawing page), and the pointer will change to the forefinger form . 3. Then, click the link. (You will go to the link destination.) Moving with bookmark: Click an item (text) on the bookmark pallet, and you can move to the link destination. Also, clicking can display the hidden items. (To go back to original state, click ) Zooming or rotating the screen display “Zoom in/out” • Click the triangle button in the zoom control box to select the display magnification. Or, you may click or for zoom- ing in or out. “Rotate” • Click rotate tool , and the page then rotates 90 degrees each. Application to the Service Manual: The printed circuit board diagram you see now can be changed to the same direction as the set. Toolbar

Sony EMCS Co. 9-876-927-82 2006B0500-1 © 2006.2 Published by DI Technical Support Department SUPPLEMENT-1 File this supplement with the service manual. (PV05-085) • Addition of UK Model (HC23E/HC26E) DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 Note: DV Interface on the Cradle (Handycam Station) Model information table &: Points add portion. (See original service manual page 3) Model DCR-HC23E DCR-HC24E DCR-HC26 DCR-HC26E DCR-HC35E Destination AEP, UK, EE, NE AEP, UK, EE, NE US, CND, E, AR UK, NE, E, AUS, AEP, UK, EE, NE BR, KR CH, HK Color system PAL PAL NTSC PAL PAL DV Interface OUT OUT IN/OUT IN/OUT IN/OUT (Note) Remote commander × a × × a Cradle (Handycam Station) × × × × a CR board × × × × CR-061 & & US Model Canadian Model AEP Model UK Model East European Model North European Model E Model Argentine Model Australian Model Brazilian model Chinese Model Hong Kong Model Korea Model DCR-HC23E/HC24E/HC26/HC26E/HC35E RMT-830

S.M. Rev. issued — No DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2 987692732.pdf