Grizzly H0583 Instruction Sheet

No-Load Speed................................... 3,000 RPM Maximum Torque.................................. 1,400 ft/lb Air Inlet Size..............................................1⁄2" NPT Air Consumption....................................... 14 CFM Operating Pressure.................................... 90 PSI Maximum Operating Pressure.................. 115 PSI Weight.......................................................28.6 lbs Inventory A.. Impact Wrench............................................ 1 B.. Side Handle................................................. 1 C.. Cap Screws................................................. 4 Setup Secure the side handle to the impact wrench with the cap screws. MODEL H0583 1" HEAVY–DUTY TWO–HAMMER IMPACT WRENCH INSTRUCTION SHEET Figure 1. Model H0583 Copyright © May, 2008 By Grizzly Industrial, Inc. Warning: No portion of this manual may be reproduced in any shape Or form without the written approval of Grizzly Industrial, inc. #JM10694 printed in TAIWAN INJURY HAZARD! Always disconnect tool from air to prevent unexpected operation during service! EYE/EAR INJURY HAZARD! Wear safety glasses and hearing protection when using this tool! DO NOT EXCEED 115 PSI! Personal injury could occur. SHATTERING HAZARD! Use sockets rated for impact wrench use only. Operation Install any 1" drive socket into your air impact wrench. Flip the forward/reverse switch, shown in Figure 1, to change direction. Connect to air line regulated at 90 PSI. Using both hands, securely hold onto the impact wrench and squeeze the throttle. Maintanence The impact wrench MUST be regularly lubricated with 3-4 drops of air tool oil directly into the air fit- ting before each use. For best results, we recom- mend using an in line filter, lubricator, and regula- tor, as shown in Figure 2. If you need help with your new pneumatic tool, call our Tech Support at: (570) 546-9663. Quick Connector Quick Coupler Air Hose Quick Coupler Quick Connector Lubricator Filter Regulator Air Compressor Your Tool Figure 2. Installing your tool. Side Handle Forward/Reverse Switch Throttle

# $ % & ' ( ) * + #" ## #% #& #' #( #) #* #+ $" $# $$ $% $& $' $( $) $* $+ %" %# %$ %% %& %' %( %) %* %+ &" &$ &% && &' &( &) &* &+ '" '# '$ '& %' %( '' #$ REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH0583001 SCREEN 28 PH0583028 REVERSE LEVER 2 PH0583002 AIR INLET 1/2" NPT 29 PRP43M ROLL PIN 3 X 22 3 PH0583003 COMPRESSION SPRING 30 PH0583030 EXHAUST DEFLECTOR 4 PH0583004 COVER 31 PH0583031 PHLP HD SCREW 5 PH0583005 THROTTLE VALVE 32 PH0583032 SPACER 6 PH0583006 O-RING 33 PH0583033 CLUTCH CAGE 7 PH0583007 RUBBER BUSHING 34 PH0583034 DRIVE CAM 8 PH0583008 THROTTLE HANDLE 35 PH0583035 CLUTCH DOG 9 PH0583009 TRIGGER 36 PH0583036 CLUTCH PIN 10 PRP05M ROLL PIN 5 X 30 37 PH0583037 FLANGE BUSHING 11 PH0583011 CAP SCREW 38 PH0583038 CLUTCH HOUSING 12 PH0583012 LOCK WASHER 39 PH0583039 BUSHING 13 PH0583013 GASKET 40 PSB03 CAP SCREW 5/16-18 X 1 14 PH0583014 BALL BEARING 42 PH0583042 ANVIL 15 PH0583015 OIL SEAL 43 PORP016 O-RING 15.8 X 2.4 P16 16 PH0583016 FRONT PLATE 44 PH0583044 EXT RETAINING RING 17 PH0583017 CYLINDER 45 PH0583045 SIDE HANDLE 18 PH0583018 ROTOR 46 PH0583046 CAP SCREW 19 PH0583019 ROTOR BLADE 47 PH0583047 RUBBER HOUSING SEAL 20 PH0583020 REAR PLATE 48 PH0583048 RUBBER THROTTLE SEAL 21 PORS065 O-RING 64.5 X 2.0 S65 49 PH0583049 SET SCREW 22 PH0583022 ROLL PIN 50 PH0583050 HOUSING OIL SEAL 23 PH0583023 MOTOR HOUSING 51 PH0583051 O-RING 24 PH0583024 MOTOR GASKET 52 PORP020 O-RING 19.8 X 2.4 P20 25 PH0583025 BUSHING 54 PH0583054 RETAINER 26 PH0583026 REVERSE VALVE *55 PH0583055 O-RING KIT 27 PORP021 O-RING 20.8 X 2.4 P21 * Not Included; for aftermarket purchase only