Panasonic PT-CW331R Specifications

Ultra Short-Throw DLP ™Projector S P E C F I L E Product Number : PT-CW331R As of June 2013. Specifications and appearance are subject to change without notice. SFD13M001-1 1 / 1 3

Specifications Main unit Power supply Power consumption DLP™ chip Panel size Display method Pixels Lens Lamp Screen size Colors Brightness* 2 Center-to-corner uniformity* 2 Contrast* 2 Resolution Scanning frequency HDMI RGB YPBPR (YCBCR) Video/S-Video Keystone correction range Installation Built-in speaker Size Output power Terminals HDMI IN COMPUTER (RGB) 1/2 IN R, G, B Y, PB (CB), PR (CR) MONITOR (RGB) OUT R, G, B VIDEO IN S-VIDEO IN 100–240 V AC, 3.6–1.5 A, 50/60 Hz 340 W (0.5 W when STANDBY MODE set to ECO,* 1 6.0 W when STANDBY MODE set to NETWORK.) 16.5 mm (0.65 inches) diagonal (16:10 aspect ratio) DLP™ chip × 1, DLP™ system 1,024,000 (1,280 × 800) pixels Fixed (0.35:1 throw ratio), manual focus, F 2.6, f 5.27 mm 280 W UHM lamp × 1 1.78– 2.54 m (70–100 inches) diagonally, 16:10 aspect ratio Full color (16,777,216 colors) 3,100 lumens (LAMP POWER: NORMAL) 80% 8,000:1 (full on/off, During RGB signal input, LAMP POWER: NORMAL) 1,280 × 800 pixels (Input signals that exceed this resolution will be converted to 1,280 × 800 pixels.) fH: 15 kHz–100 kHz, fV: 24 Hz–120 Hz, dot clock: 25 MHz–162 MHz fH: 15 kHz–100 kHz, fV: 24 Hz–120 Hz, dot clock: 162 MHz or lower 525i (480i): fH 15.75 kHz; fV 60 Hz, 625i (576i): fH 15.63 kHz; fV 50 Hz, 525p (480p): fH 31.50 kHz; fV 60 Hz, 625p (576p): fH 31.25 kHz; fV 50 Hz, 750 (720)/60p: fH 45.00 kHz; fV 60 Hz, 750 (720)/50p: fH 37.50 kHz; fV 50 Hz, 1125 (1080)/60i: fH 33.75 kHz; fV 60 Hz, 1125 (1080)/50i: fH 28.13 kHz; fV 50 Hz 1125 (1080)/24p: fH 27.00 kHz; fV 24 Hz 1125 (1080)/60p: fH 67.50 kHz; fV 60 Hz 1125 (1080)/50p: fH 56.25 kHz; fV 50 Hz fH: 15.75/15.63 kHz, fV: 50/60 Hz [NTSC/NTSC4.43/PAL/PAL60/PAL-N/PAL-M/SECAM] Vertical: ±15° Ceiling/floor, front/rear (Menu setting) 7 x 3 cm (2-3/4 x 1-3/16 inches) (oval-shaped) × 1 10 W (monaural) HDMI 19-pin × 1, HDCP compatible, Deep color compatible 525p (480p), 625p (576p), 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p, 1125 (1080)/60p, 1125 (1080)/50p VGA (640 × 480) – WSXGA+ (1,680 × 1,050), Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz) D-sub HD 15-pin (female) × 2 G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms; B, R: 0.7 Vp-p, 75 ohms; HD/VD, SYNC: high impedance, TTL, positive/negative automatic Y: 1.0 Vp-p (including sync signal); PB (CB), PR (CR): 0.7 Vp-p, 75 ohms Y, PB (CB), PR (CR) Y: 1.0 Vp-p (including sync signal); PB (CB), PR (CR): 0.7 Vp-p, 75 ohms D-sub (Outputs signals selected from RGB input 1/2.) HD 15-pin (female) × 1 G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms; B, R: 0.7 Vp-p, 75 ohms; HD/VD, SYNC: high impedance, TTL, positive Pin jack × 1, 1.0 Vp-p, 75 ohms Mini DIN 4-pin × 1, Y: 1.0 Vp-p; C: 0.286 Vp-p, 75 ohms As of June 2013 SFD13M001-1 2 / 1 3 PT-CW331R

3 / 1 3 COMPUTER 1 AUDIO IN COMPUTER 2 AUDIO IN VIDEO/S-VIDEO AUDIO IN AUDIO OUT SERIAL IN LAN MiniUSB Power cord length Cabinet materials Dimensions (W × H × D) Weight Operation noise Operating temperature Operating humidity Remote control unit Power supply Operation range* 4 Dimensions (W × H × D) Weight Supplied accessories Optional accessories Ceiling mount bracket Bracket assembly Wall mount bracket Replacement Interactive Pen Interactive Pointer ET-PEN100 ET-PNT100 lamp unit M3 (L, R) × 1, 0.5 Vrms M3 (L, R) × 1, 0.5 Vrms Pin jack × 2 (L/R × 1), 0.5 Vrms M3 (L, R) × 1 (monitor out: 0– 2.0 Vrms, variable) D-sub 9-pin (female) × 1, for external control (RS-232C compliant) RJ-45 × 1, for network connection, 100Base-TX/10Base-T, compliant with PJLink™ MiniUSB x 1 (For interactive function) 3.0 m (9 ft 10 in) Molded plastic (PC) 357 mm × 250 mm* 3 × 367 mm (14-1/16 × 9-27/32*3 × 14-7/16 inches) Approximately 7.8 kg (17.6 lbs) 37 dB (LAMP POWER: NORMAL), 33 dB (LAMP POWER: ECO) 5–40 °C (41–104 °F) up to 750 m (2,500 ft) above sea level, 5–30 °C (41–86 °F) between 1,500 m and 3,000 m (5,000 ft and 10,000 ft) above sea level. 5–35 °C (41–95 °F) between 750 m and 1,500 m (2,500 ft and 5,000 ft) above sea level. 20%–80% (no condensation) 3 V DC (Lithium coin cell battery × 1) Approximately 8 m (26.3 ft) when operated from directly in front of the signal receptor 41 × 87 × 7 mm (1-5/8 × 3-7/16 × 9/32 inches) Approx. 23 g (0.8 oz) (including Lithium coin cell battery) Power cord (× 1) (× 2 for PT-CW331REA) Power code cover (x 1) Power code holder (x 1) Wireless remote control unit (× 1) Lithium coin cell battery for remote control (× 1) Computer cable (1.8 m) (x 1) ET Interactive Pen (x 2) AAA type battery (x 4) USB cable (5.0 m) (x 1) Software CD-ROM (Interactive function manual, LightPenⅢ) (x 1) -PKV100H (for high ceilings) ET-PKV100S (for low ceilings) ET-PKC200B ET-PKC200W ET-LAC300 Weights and dimensions shown are approximate. Specifications subject to change without notice. *1 When the standby mode is set to eco, network functions such as LAN Standby On and MONITOR OUT/AUDIO OUT terminals do not work. *2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. *3 With legs at shortest position. *4 Operation range differs depending on environments. As of June 2013 SFD13M001-1 PT-CW331R

NOTE: This illustration is not drawn to scale. S P E C F I L E Ultra Short-Throw DLP™Projector 4 / 1 3 Terminals 1 MiniUSB 2 HDMI input 3 Monitor output 4 LAN connector 5 Computer 1 input 6 Audio input for computer 1 7 S-Video input 8 Audio input for S-Video 9 Serial input 10 Computer 2 input 11 Audio input for computer 2 12 Video input 13 Audio input for video 14 Audio output As of June 2013 SFD13M001-1 PT-CW331R 231 (9-3/32) 250 (27/32) 19 (3/4) 187 (7-3/8)

5 / 1 3 Standard setting-up position unit : mm (inch) NOTE: Illustrations show the projector installed using optional ceiling mount bracket ET-PKV100H and bracket assembly ET-PKC200B. This illustration is not drawn to scale. As of June 2013 SFD13M001-1 C a u t i o n : • All construction work should be done by a qualified technician. • When mounting to the ceiling, use the special mounting bracket. Furthermore, in order to prevent it from falling down from the ceiling, use the supplied wire on the mounting bracket. 1106.5–1676.5 (43-9/16 – 66) Adjustable in 30-mm (1-3/16-inch) step. Projected image Projected image Lower edge of projected image Upper edge of projected image ∅38 (1-1/2) 100 (3-15/16) 100 (3-15/16) 200 (7-7/8) 70 (2-3/4) 140 (5-1/2) 70 (2-3/4) 56 (2-7/32) (4-1/32) (9-1/8) 102.5 232 A B E F A B E F

6 / 1 3 Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:10 A (m) = (diagonal screen size in inches) × 0.00810 – 0.0508 Aspect ratio 16:9 A (m) = (diagonal screen size in inches) × 0.00832 – 0.0507 NOTE: Distances calculated with the above equations will include a slight error. 70 80 90 100 Screen size (inch, diagonal) A: Distance from the edge of the projection window to the screen B: Distance from the projector front to the screen E: Height from the edge of the screen to the top of the projector F: Height from the edge of the screen to the bottom of the projector 0.6 0.9 1.1 1.4 1.7 2.0 2.2 2.5 Unit: feet 70 80 90 Screen size (inch, diagonal) A: Distance from the edge of the projection window to the screen B: Distance from the projector front to the screen E: Height from the edge of the screen to the top of the projector F: Height from the edge of the screen to the bottom of the projector 0.7 0.9 1.2 1.7 2.0 2.3 Unit: feet 70 80 90 Screen size (inch, diagonal) A: Distance from the edge of the projection window to the screen B: Distance from the projector front to the screen E: Height from the edge of the screen to the top of the projector F: Height from the edge of the screen to the bottom of the projector 0.20 0.28 0.36 0.53 0.61 0.70 Projection distance for 16:9 aspect ratio screen Unit: meters As of June 2013 SFD13M001-1 70 80 90 100 Screen size (inch, diagonal) A: Distance from the edge of the projection window to the screen B: Distance from the projector front to the screen E: Height from the edge of the screen to the top of the projector F: Height from the edge of the screen to the bottom of the projector 0.18 0.26 0.34 0.42 0.52 0.60 0.68 0.76 Projection distance for 16:10 aspect ratio screen Unit: meters PT-CW331R 1.0 1.1 1.2 1.3 0.5 0.6 0.7 0.8 1.2 1.3 1.5 0.7 0.8 1.0 0.36 0.40 0.44 0.21 0.25 0.29 0.30 0.34 0.37 0.41 0.15 0.19 0.22 0.25

7 / 1 3 Installable angle Install the projector at an angle within the range shown below. • Vertical direction The projector may be installed at a vertical angle . • Horizontal direction The projector may be installed at a horizontal angle of ±10°. As of June 2013 SFD13M001-1 of ±10° +10° -10° +10° -10° PT-CW331R

8 / 1 3 List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning fre- quencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of 162 MHz maximum can be input. NOTE: The native resolution of this projector is 1,280 × 800 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution. Display mode Display resolution (dots)1 Scanning frequency H (kHz) V (Hz) Dot clock frequency (MHz) Format 720 × 480i 720 × 576i 720 × 480i 720 × 576i 720 × 483 720 × 576 1280 × 720 1920 × 1080i 1920 × 1080 640 × 480 720 × 400 800 × 600 15.7 15.6 15.7 15.7 15.6 15.6 31.5 31.3 45.0 37.5 33.8 28.1 27.0 67.5 56.3 31.5 35.0 37.5 37.9 43.3 61.9 31.5 35.1 37.9 46.9 48.1 53.7 77.4 49.1 59.9 50.0 59.9 59.9 50.0 50.0 59.9 50.0 60.0 50.0 60.0 50.0 24.0 60.0 50.0 59.9 66.7 75.0 72.8 85.0 120.0 70.1 56.3 60.3 75.0 72.2 85.1 119.9 74.6 – – 27.0 13.5 13.5 27.0 27.0 27.0 74.3 74.3 74.3 74.3 74.3 148.5 148.5 25.2 30.2 31.5 31.5 36.0 52.5 28.3 36.0 40.0 49.5 50.0 56.3 83.0 57.3 NTSC/NTSC4.43/PAL-M/PAL60 PAL/PAL-N/SECAM 525i (480i) 625i (576i) 525p (480p) 625p (576p) 750(720)/60p 750(720)/50p 1125(1080)/60i 1125(1080)/50i 1125(1080)/24p 1125(1080)/60p 1600 × 1200 1400 × 1050 1280 × 960 1280 × 1024 1680 × 1050 65.3 75.0 65.3 60.0 60.0 60.0 121.8 162.0 146.3 SXGA+ UXGA WSXGA+ 1125(1080)/50p VGA SVGA MAC16 VIDEO/S-VIDEO HDMI HDMI YCBCR YCBCR HDMI/YPBPR 60.0 75.2 60.0 75.0 108.0 130.0 SXGA HDMI/RGB 832 × 624 48.4 56.5 60.0 68.7 99.0 60.0 70.1 75.0 85.0 119.8 65.0 75.0 78.8 94.5 137.8 XGA 1280 × 720 1024 × 768 44.8 49.7 47.7 55.9 1280 × 800 1366 × 768 1440 × 900 60.0 59.8 59.8 59.9 74.5 83.5 84.8 106.5 WXGA 64.0 77.0 80.0 60.0 72.0 75.0 108.0 133.0 135.0 68.7 75.1 100.0 MAC21 1152 × 870 *1 The “i” appearing after the resolution indicates an interlaced signal. As of June 2013 SFD13M001-1 PT-CW331R

9 / 1 3 3D-compliant signal list The 3D signals that can be input to this projector are as follows. Display mode Display resolution (dots)1 Scanning frequency H (kHz) V (Hz) Dot clock frequency (MHz) HDMI Frame packing Side by side Top and bottom Frame sequential Frame sequential Frame sequential Filled sequential Computer1/2 Video/S-Video 1280 × 720 1920 × 1080i 1920 × 1080 640 × 480 800 × 600 45.0 37.5 33.8 28.1 27.0 61.9 77.4 60.0 50.0 60.0 50.0 24.0 119.5 119.9 74.3 74.3 74.3 74.3 74.3 52.5 83.0 750(720)/60p 750(720)/50p 1125(1080)/60i 1125(1080)/50i 1125(1080)/24p Video/S-Video VGA SVGA 99.0 119.8 137.8 XGA 1024 × 768 As of June 2013 SFD13M001-1 – – – – ○ ○ ○ × × × × × × × × × ○ ○ × × × × ○ ○ ○ × × × × × × × × × × × ○ ○ ○ – × × × × × ○ ○ ○ × × × × × × × × × ○ × × × × × × × × ○ Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, com- mands must be input through communication software, based on the format and satisfying the commu- nication conditions shown below. Communication conditions (factory setting) Pin assignments and signal names 6 1 5 9 D-sub 9-pin (female) Serial input Description NC Send data Receive data NC Ground Signal name – TXD RXD – GND No. 1 2 3 4 5 Description NC Connected internally Connected internally NC Signal name – CTS RTS – No. 6 7 8 9 Signal level Synchronization method Baud rate Parity Character length Stop bit X parameter S parameter RS-232C-compliant Start-stop synchronization 19,200 bps None 8 bits 1 bit None None PT-CW331R

1 0 / 1 3 As of June 2013 SFD13M001-1 Control commands Command : Parameter Function Callback PON POF IIS:HD1 IIS:RG1 IIS:RG2 IIS:VID IIS:SVD OSH:0 OSH:1 POWER (STANDBY) INPUT SELECT AV MUTE PON POF IIS:HD1 IIS:RG1 IIS:RG2 IIS:VID IIS:SVD OSH:0 OSH:1 Standby power on Standby power off HDMI RGB 1 RGB 2 Video S-Video AV mute off AV mute on Cable specifications 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 PC (DTE) Projector NC NC NC NC NC NC NC NC * Do * STX and ETX are character chords. STX is 02 and ETX is 03 when expressed in hexadecimal. not send PON, POF or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle. * When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply. Basic format Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control. CAUTION • It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again. • When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next command. • Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for com- mand response to 10 seconds or more. Start (1 byte) End (1 byte) Colon (1 byte) Parameters (undefined length) Command (3 bytes) (Control and/or query commands) STX ETX C1 P1 P2 ... Pn C2 C3 : PT-CW331R

1 1 / 1 3 As of June 2013 SFD13M001-1 Status request commands Command:Parameter Function Description Callback QPW QSH QIN QVX:RTMI0 Q$L Main power status AV mute function status Input signal status Projector run time Lamp run time Standby On Standby Off On HDMI RGB 1 RGB 2 Video S-Video 00000h–99999h 0000h–9999h 000 001 0 1 HD1 RG1 RG2 VID SVD Q$S Lamp on status 0 1 2 3 p1p2p3p4p5 p1p2p3p4 QTM:0 Temperature status p0 = Internal temperature p1p2p3p4/p5p6p7p8 (*1) * 1 p1p2p3p4: Celsius (°C), p5p6p7p8: Fahrenheit (°F) Command example To s et the AV mute function off, send the command as shown below. OSH : 0 ETX Command STX Start Parameter End NOTE: When sending commands without parameters, a colon (:) is not necessary. NOTE: If a wrong command is received, the projector will send an ER401 or ER402 command to the computer. Lamp on control in progress Lamp on Lamp off control in progress PT-CW331R

1 2 / 1 3 Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector while it is operating. 2. Make sure there is the unobstructed space as shown below or more around the projector’s exhaust openings. In addition to this space, also ensure that there is a sufficient work space for removing and installing the lamp, air filter and other parts. 3. Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install the pro- jector so that cool or hot air from other air conditioning equipment does not flow directly toward the projector’s air intake or exhaust openings. 4. Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the intake opening. This may cause the projector’s protective circuit to interrupt projector operation. Direction of air intake and exhaust As of June 2013 SFD13M001-1 500 mm (19-11/16˝) or more 100 mm (3-15/16˝) or more 1000 mm (39-3/8˝) or more Intake Exhaust PT-CW331R

1 3 / 1 3 Operating the projector continuously 1. If the projector is to be operated continuously 22 hours or more, lamp replacement cycle duration becomes shorter. 2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods (one hour or less). As of June 2013 SFD13M001-1 PT-CW331R Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice. Product availability differs depending on region and country. This product may be subject to export control regulations. DLP and the DLP logo are trademarks of Texas Instruments. P HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. JLink is a registered trademark, or a trademark application has been filed, in Japan, the United States, and other countries and regions. All other trademarks are the property of their respective trademark owners.