Panasonic PT-D5700 Specifications
Text of the manual
< 1 >
S
P
E
C
F
I
L
E
Product Number : PT-D5700/D5700L
Product Name :
DLP ™Projectors
As of May 2007. Specifications subject to change without notice.
The PT-D5700L is not equipped with a lens.
As of May 2007
< 2 >
Specifications
Main Unit
Power supply:
North America:
Europe:
Power consumption:
North America:
Europe:
DLP™chip:
Panel size:
Display method:
Pixels:
Lens:
PT-D5700:
PT-D5700L:
Lamp:
Screen size:
Brightness* 1:
Center-to-corner uniformity* 1:
Contrast* 1:
Resolution:
Scanning frequency:
RGB:
YPBPR (YCBCR):
S-Video/Video:
Optical axis shift:
Keystone correction range:
Installation:
Terminals* 2:
DVI-D IN:
RGB 1 IN:
R, G, B:
Y, PB, PR:
RGB 2 IN:
R, G, B:
Y, PB, PR:
VIDEO IN:
S-VIDEO IN:
SERIAL IN:
SERIAL OUT:
REMOTE 1 IN:
REMOTE 1 OUT:
REMOTE 2 IN:
LAN:
Power cord length:
Cabinet materials:
120 V AC, 50/60 Hz
220–240 V AC, 50/60 Hz
770 W (770 VA) (10 W during standby mode with fan stopped)
750 W (790 VA) (15 W during standby mode with fan stopped)
0.7˝ diagonal (4:3 aspect ratio)
DLP™ chip x 1, DLP™ system
786,432 (1,024 x 768) x 1, total of 786,432 pixels
Powered zoom/focus lenses (4:3 aspect ratio: 1.8–2.4:1),
F 1.7–2.0, f 25.6–33.8 mm
Optional poweredzoom/focus lenses
300 W UHM™ lamps (x 2) (dual lamp system)
50–600 inches (50–200 inches with the ET-DLE050), 4:3 aspect ratio
6,000 lumens (dual lamp, high power mode)
90%
2,000:1 (full on/full off, contrast mode: high, brightness: 3,000 lumens)
1,000:1 (full on/full off, contrast mode: normal)
1,024 x 768 pixels
(1,600 x 1,200 pixels compatible, compression mode)
Horizontal: 15–91 kHz, Vertical: 50–85 Hz,
Dot clock: 150 MHz or lower
480i: fH 15.75 kHz; fV 59.94 Hz, 576i: fH 15.63 kHz; fV 50 Hz,
480p: fH 31.50 kHz; fV 59.94 Hz, 576p: fH 31.25 kHz; fV 50 Hz,
720/60p: fH 45 kHz; fV 60 Hz, 720/50p: fH 37.5 kHz; fV 50 Hz,
1035/60i: fH 33.75 kHz; fV 60 Hz, 1080/60i: fH 33.75 kHz; fV 60 Hz,
1080/50i: fH 28.13 kHz; fV 50 Hz, 1080/60p: fH 67.5 kHz; fV 60 Hz,
1080/50p: fH 56.25 kHz; fV 50 Hz
Horizontal: 15.75/15.63 kHz, Vertical: 50/60 Hz,
(NTSC, NTSC4.43, PAL, PAL60, PAL-N, PAL-M, SECAM)
Horizontal (manual) and vertical (powered),
Horizontal: ±10%, vertical: +50%
Vertical: ±30°
Ceiling/floor, front/rear
DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible, for single link
only
480p, 576p, 1080/60i, 1080/50i, 1080/60p, 1080/50p, 720/60p,
720/50p, VGA60, SVGA60, XGA50, XGA60, XGA70, XGA75, XGA85,
SXGA50, SXGA60, SXGA+60, WXGA768/50, WXGA768/60
BNC x 5
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
B, R: 0.7 Vp-p, 75Ω
HD/VD, SYNC: TTL (positive/negative)
Y: 1.0 p-p, 75Ω (including sync signal), PB/PR: 0.7 Vp-p, 75Ω
D-sub HD 15-pin x 1
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
B, R: 0.7 Vp-p, 75Ω
HD/VD, SYNC: TTL (positive/negative)
Y: 1.0 p-p, 75Ω (including sync signal), PB,/PR: 0.7 Vp-p, 75Ω
BNC x 1, 1.0 Vp-p, 75Ω
Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75Ω
D-sub 9-pin x 1 (RS-232C compliant) for external controller
D-sub 9-pin x 1 (RS-232C compliant) for external controller
M3 jack x 1 for wired remote control or link control
M3 jack x 1 for link control
D-sub 9-pin x 1 for external control (parallel)
RJ-45 x 1, compliant with PJLink™, 10Base-T/100Base-TX
3.0 m (9´10˝)
Molded plastic
As of May 2007
< 3 >
On-screen menu:
Dimensions (W x H x D): PT-D5700
PT-D5700L
Weight:
PT-D5700
PT-D5700L
Operating temperature:
Operating humidity:
Remote Control Unit
Power supply:
Operation range* 3:
Wireless:
Dimensions (W x H x D):
Weight:
Supplied Accessories
Optional Accessories
Replacement lamp unit:
Ceiling mount bracket:
Zoom lens (1.3-1.8:1)
Zoom lens (2.4-4.0:1)
Zoom lens (3.8-6.0:1)
Zoom lens (5.8-8.1:1)
Fixed-focus lens (0.8:1)
9 languages: English, French, German, Spanish, Italian, Russian,
Korean, Chinese, and Japanese
530 x 167 x 441 mm (20-7/8˝ x 6-9/16˝ x 17-3/8˝) (with supplied lens)
530 x 167 x 429 mm (20-7/8˝ x 6-9/16˝ x 16-7/8˝) (without lens)
13.9 kg (30.6 lbs) (with supplied lens)
13.1 kg (28.9 lbs) (without lens)
0°–45°C (32°–113°F)
20%–80% (no condensation)
3 V DC (AA battery x 2)
Approx. 30 m (98.4 feet) when operated from directly in front of the
signal receptor
51 x 176 x 22.5 mm (2˝ x 6-15/16˝ x 7/8˝)
134 g (4.7 oz) (including batteries)
Power cord, Wireless/wired remote control unit, Batteries for remote
control (x 2), Wire rope
ET-LAD57 (1 unit)
ET-LAD57W (set of two lamps)
ET-PKD56H (for high ceilings)
ET-PKD55S (for low ceilings)
ET-DLE100
ET-DLE200
ET-DLE300
ET-DLE400
ET-DLE050
86.5
(3-13/32)
157 (6-3/16)
167 (6-9/16)
R30
(1-3/16)
368 (14-1/2)
478.5
(18-27/32)
425 (16-23/32)
441 (17-3/8)
4 (5/32)
12 (15/32)
436 (17-5/32)
530 (20-7/8)
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
The illustration shows the PT-D5700.
Dimensions
Weights and dimensions shown are approximate. Specifications subject to change without notice.
*1
Values indicate overall average values of the product at the time of shipment and are stated based on JIS X 6911:2003 Data Projector
Specification Sheet Format. Measurement method and conditions are based on Appendix 2.
*2
The HD/SYNC and VD inputs do not accept the tri-level sync signal.
*3
Operation range differs depending on environments.
As of May 2007
< 4 >
Terminals
RGB IN connector pin assignment
1
Video input
2
S-Video input
3
RGB 1 input
4
RGB 2 Input
5
DVI-D input
6
LAN connector
7
Remote 1 input and output
8
Remote 2 input
9
Serial input
10 Serial output
no.
1
2
3
4
5
no.
6
7
8
9
10
no.
11
12
13
14
15
signal
R/PR
G/Y
B/PB
GND
GND
signal
GND
GND
GND
NC
GND
signal
GND
NC
HD/SYNC
VD
NC
DVI-D output connector pin assignment
no.
1
2
3
4
5
6
7
8
no.
9
10
11
12
13
14
15
16
no.
17
18
19
20
21
22
23
24
signal
T, M, D, S data 2-
T, M, D, S data 2+
T, M, D, S data 2 shield
NC
NC
DDC clock
DDC clock
NC
signal
T, M, D, S data 1-
T, M, D, S data 1+
T, M, D, S data 1 shield
NC
NC
+5 V
GND
Hot plug detection
signal
T, M, D, S data 0-
T, M, D, S data 0+
T, M, D, S data 0 shield
NC
NC
T, M, D, S clock shield
T, M, D, S clock +
T, M, D, S clock -
1
7
8
9
10
2
3
4
5
6
Upper edge of projected image
Attachment
plate
261
(10-9/32˝)
*3
Lower edge of projected image
Projected image
L
L
109
(4-9/32˝)
76.5 (3˝)
157
(6-3/16˝)
87.5
(3-7/16˝)
L
Projected image
H
H
S
P
E
C
F
I
L
E
PT-D5700/D5700L
DLP ™Projectors
As of May 2007
< 5 >
unit : mm (inch)
*3 When the lens protrudes to the maxi-
mum.
185 mm (7-9/32˝) with the supplied lens
177 mm (6-31/32˝) with the ET-DLE050
209 mm (8-7/32˝) with the ET-DLE100
208 mm (8˝-3/16˝) with the ET-DLE200
196 mm (7-23/32˝) with the ET-DLE300
196 mm (7-23/32˝) with the ET-DLE400
*4 Adjustable in 40 mm (1-9/16˝) steps.
Standard setting-up position (when installed using the ET-PKD56H)
Standard setting-up position (when installed using the ET-PKD55S)
Upper edge of projected image
256
(10-3/32˝)
*1
*2
Lower edge of projected image
Projected image
L
L
L
340–420
(13-3/8˝–
16-17/32˝)
417–497
(16-13/32˝–
19-9/16˝)
100
(3-15/16˝)
344
(13-17/32˝)
100
(3-15/16˝)
400
(15-3/4˝)
Projected image
H
H
NOTE:
Illustrations show the projector installed
using optional ceiling bracket.
This illustration is not drawn to scale.
Values shown are approximate.
The value for L (distance to screen) varies
slightly depending on the zoom lens char-
acteristics. When the shortest projection
distance (min.) is used, a small amount of
distortion may occur in the image due to
the zoom lens characteristics.
unit : mm (inch)
*3 When the lens protrudes to the maxi-
mum.
180 mm (7-3/32˝) with the supplied lens
172 mm (6-25/32˝) with the ET-DLE050
204 mm (8-1/32˝) with the ET-DLE100
203 mm (8˝) with the ET-DLE200
191 mm (7˝-17/32˝) with the ET-DLE300
191 mm (7-17/32˝) with the ET-DLE400
C A U T I O N
The ET-DLE050 has a fixed short-focus lens. Therefore, the lens shift function provided in the main
unit cannot be used.
If the lens shift function is used, the corners of images may not be displayed or images may remain
out of focus in some cases.
As of May 2007
< 6 >
Projection distance for 4:3 aspect ratio screen
50
60
70
80
90
100
120
150
200
250
300
400
500
600
Screen
size
(inch,
diagonal)
min.
max.
min.
max.
Zoom
Zoom
lenses
Fixed-focus
Fixed-
focus
lens
Distance to screen (L)
Height from the edge
of screen to
center of lens (H)
min.
max.
min.
max.
min.
max.
ET-DLE100
Zoom lens
Supplied lens
ET-DLE200
Zoom lens
ET-DLE300
Zoom lens
ET-DLE400
Zoom lens
ET-DLE050
Fixed-focus
lens
–
–
–
–
–
–
–
–
–
–
–
–
–
–
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0.38
0.46
0.53
0.61
0.69
0.76
0.91
1.14
1.52
1.91
2.29
3.05
3.81
4.57
0.794
0.960
1.126
1.292
1.458
1.624
1.956
2.454
3.284
–
–
–
–
–
0.381
0.457
0.533
0.610
0.686
0.762
0.914
1.143
1.524
–
–
–
–
–
1.4
1.7
1.9
2.2
2.5
2.8
3.3
4.1
5.5
6.9
8.3
11.0
13.8
16.6
1.8
2.1
2.5
2.9
3.3
3.6
4.4
5.5
7.3
9.2
11.1
14.8
18.5
22.2
1.8
2.2
2.6
2.9
3.3
3.7
4.4
5.5
7.4
9.2
11.1
14.8
18.5
22.2
2.3
2.8
3.3
3.8
4.3
4.8
5.7
7.2
9.6
12.1
14.5
19.4
24.3
29.2
2.5
3.0
3.5
4.0
4.5
5.0
6.0
7.5
10.1
12.6
15.1
20.1
25.2
30.2
4.0
4.8
5.6
6.5
7.3
8.1
9.8
12.2
16.4
20.5
24.6
32.8
41.1
49.3
3.9
4.7
5.5
6.3
7.1
7.9
9.5
11.8
15.8
19.8
23.8
31.7
39.7
47.6
6.0
7.2
8.4
9.7
10.9
12.1
14.6
18.3
24.5
30.6
36.8
49.1
61.4
73.7
6.0
7.1
8.3
9.5
10.7
11.8
14.2
17.7
23.6
29.5
35.4
47.1
58.9
70.6
8.2
9.9
11.5
13.2
14.8
16.5
19.8
24.7
32.9
41.2
49.4
65.9
82.3
98.8
50
60
70
80
90
100
120
150
200
250
300
400
500
600
Screen
size
(inch,
diagonal)
min.
max.
min.
max.
Zoom
Zoom
lenses
Fixed-focus
Fixed-
focus
lens
Distance to screen (L)
Height from the edge
of screen to
center of lens (H)
min.
max.
min.
max.
min.
max.
ET-DLE100
Zoom lens
Supplied lens
ET-DLE200
Zoom lens
ET-DLE300
Zoom lens
ET-DLE400
Zoom lens
ET-DLE050
Fixed-focus
lens
–
–
–
–
–
–
–
–
–
–
–
–
–
–
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1.25
1.50
1.75
2.00
2.25
2.50
3.00
3.75
5.00
6.25
7.50
10.00
12.50
15.00
2.605
3.149
3.694
4.239
4.783
5.328
6.417
8.051
10.774
–
–
–
–
–
1.250
1.500
1.750
2.000
2.250
2.500
3.000
3.750
5.000
–
–
–
–
–
4.4
5.3
6.2
7.1
8.1
9.0
10.8
13.5
18.0
22.5
27.1
36.1
45.2
54.2
5.9
7.1
8.3
9.6
10.8
12.0
14.4
18.1
24.2
30.3
36.4
48.6
60.8
73.0
5.9
7.1
8.3
9.5
10.8
12.0
14.4
18.0
24.1
30.2
36.3
48.4
60.5
72.7
7.7
9.3
11.0
12.6
14.2
15.8
19.0
23.8
31.8
39.8
47.8
63.8
79.8
95.8
8.1
9.8
11.4
13.1
14.7
16.4
19.7
24.6
32.9
41.2
49.4
66.0
82.5
99.0
13.2
15.9
18.6
21.3
24.0
26.7
32.1
40.3
53.8
67.3
80.8
107.8
134.9
161.9
12.6
15.2
17.9
20.5
23.1
25.7
30.9
38.7
51.8
64.8
77.8
103.9
130.0
156.1
19.7
23.8
27.8
31.9
35.9
39.9
48.0
60.2
80.4
100.6
120.8
161.2
201.6
242.0
19.4
23.3
27.1
31.0
34.9
38.7
46.4
58.0
77.3
96.6
115.9
154.5
193.0
231.6
27.2
32.6
38.0
43.4
48.8
54.2
65.0
81.2
108.2
135.2
162.2
216.2
270.2
324.2
Projection distance for 4:3 aspect ratio screen
(feet)
(meters)
•
The value for L (distance to screen) varies slightly depending on the zoom lens characteristics.
•
At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
•
When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
•
For the ET-DLE050, the height from the edge of the screen to the center of the lens (H) is 1/2 of the screen height.
•
The brightness varies depending on the zoom setting.
As of May 2007
< 7 >
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 4:3
minimum
L (m) = (diagonal screen size in inches) x 0.0276 - 0.0452
maximum
L (m) = (diagonal screen size in inches) x 0.0372 - 0.0478
minimum
L (m) = (diagonal screen size in inches) x 0.0370 - 0.0650
maximum
L (m) = (diagonal screen size in inches) x 0.0488 - 0.0638
minimum
L (m) = (diagonal screen size in inches) x 0.0504 - 0.0657
maximum
L (m) = (diagonal screen size in inches) x 0.0824 - 0.0758
minimum
L (m) = (diagonal screen size in inches) x 0.0795 - 0.1380
maximum
L (m) = (diagonal screen size in inches) x 0.1232 - 0.1310
minimum
L (m) = (diagonal screen size in inches) x 0.1176 + 0.0244
maximum
L (m) = (diagonal screen size in inches) x 0.1646 + 0.0651
(fixed focus)
L (m) = (diagonal screen size in inches) x 0.0166 - 0.0361
ET-DLE100
Supplied lens
ET-DLE200
ET-DLE300
ET-DLE400
ET-DLE050
•
Distances calculated with the above equations will include a slight error.
•
When an SXGA signal is input, the left and right edges of the image are blanked, and the image is projected at a screen aspect ratio of 5:4.
•
The brightness varies depending on the zoom setting.
H
(Width of
projected image)
V
(Height of
projected image)
0.5V
0.1H
0.1H
Standard postition
of projected image
Shift range
Optical axis shift function allows to shift the
position of a projected image as shown.
Installable angle
Install the projector at an angle within the range shown below.
• Vertical direction
The projector may be installed at a vertical
angle of 360°.
• Horizontal direction
The projector may be installed at a horizontal
angle of ±10°.
As of May 2007
< 8 >
List of compatible signals
This projector supports RGB signals with horizontal frequencies of 15 to 91 kHz, vertical frequencies of
50 to 85 Hz and up to 150 MHz dot clock.
NOTE:
The native resolution of this projector is 1,024 x 768 pixels. If the display resolution of the input signal is different from the
native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
Display mode
Display
resolution
(dots)1
Scanning frequency
H
(kHz)
V
(kHz)
Dot clock
frequency
(MHz)
Picture
quality2
Format
720 x 480i
720 x 576i
720 x 480i
720 x 576i
720 x 483
720 x 576
1,280 x 720
1,280 x 720
1,920 x 1,080i
1,920 x 1,080i
1,920 x 1,080
1,920 x 1,080
640 x 400
640 x 480
800 x 600
832 x 624
1,024 x 768
1,280 x 768
1,280 x 800
1,152 x 864
1,152 x 870
1,280 x 960
1,280 x 1,024
1,400 x 1,050
1,600 x 1,200
15.7
15.6
15.7
15.6
31.5
31.3
45.0
37.5
33.8
28.1
67.5
56.3
31.5
37.9
31.5
35.0
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
39.6
48.4
56.5
60.0
68.7
35.5
39.6
47.7
41.3
49.7
64.0
67.5
76.7
68.7
60.0
64.0
80.0
91.1
64.0
75.0
59.9
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
60.0
50.0
70.1
85.1
59.9
66.7
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.6
50.0
60.0
70.1
75.0
85.0
87.0
50.0
60.0
50.0
59.8
71.2
74.9
85.0
75.1
60.0
60.0
75.0
85.0
60.0
60.0
-
-
13.5
13.5
27.0
27.0
74.3
74.3
74.3
74.3
148.5
148.5
25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
51.9
65.0
75.0
78.8
94.5
44.9
65.2
80.1
68.0
83.5
94.2
108.0
121.5
100.0
108.0
108.0
135.0
157.5
108.0
162.0
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
AA
AA
AA
AA
AA
AA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
480i (525i)
576i (625i)
480p (525p)
576p (625p)
720/60p
720/50p
1080/60i
1080/50i
1080/60p
1080/50p
VGA400
VGA480
SVGA
MAC16
XGA
WXGA
MXGA
MAC21
MSXGA
SXGA
SXGA+
UXGA
VIDEO/S-VIDEO
YPBPR /RGB
YPBPR /RGB/DVI
RGB
RGB/DVI
RGB
RGB/DVI
RGB
RGB/DVI
RGB
RGB/DVI
RGB
RGB/DVI
RGB
RGB/DVI
RGB
1. The “i” appearing after the resolution indicates an interlaced signal.
2. The following symbols are used to indicate picture quality.
AA
Maximum picture quality can be obtained.
A
Signals are converted by the image processing circuit before picture is projected.
As of May 2007
< 9 >
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, com-
mands must be input through communication software, based on the format and satisfying the commu-
nication conditions shown below.
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
Communication conditions (factory setting)
Pin assignments and signal names
D-sub 9-pin (female)
Serial input
Description
NC
Send data
Receive data
Connected internally
Ground
Signal name
–
TXD
RXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
CTS
RTS
–
No.
6
7
8
9
Pin assignments and signal names
D-sub 9-pin (male)
Serial output
Description
NC
Receive data
Send data
Connected internally
Ground
Signal name
–
RXD
TXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
RTS
CTS
–
No.
6
7
8
9
CAUTIION
• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this
occurs, wait for 60 seconds, then try sending or receiving again.
• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before
sending the next command.
• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for com-
mand response to 10 seconds or more.
Start
(1 byte)
End
(1 byte)
Colon
(1 byte)
Semicolon
(1 byte)
ID designator:
01 to 64: Address number
0A to 0Z: Group ID
ZZ: All units (ID ALL)
ID 2 characters
(2 bytes)
Parameters
(undefined length)
Command
(3 bytes)
(Control and/or query commands)
STX
ETX
C1
P1 P2 ... Pn
C2
A
D
I1 I2
C3
:
;
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
9,600 bps
None
8 bits
1 bit
None
None
As of May 2007
< 10 >
Control commands
* 1
Do not send PON, POF, OSH, or OLP commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle.
* 2
When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply.
Command : Parameter
Function
Item
Callback
PON *1
POF *1
OFZ:0
OFZ:1
OAS
OSH:0*1/*2
OSH:1*1/*2
IIS:RG1
IIS:RG2
IIS:VID
IIS:SVD
IIS:DVI
OTS:00
OTS:01
OTS:02
OTS:03
OTS:05
OTS:07
OTS08
OOS:0
OOS:1
Power on
Standby power off
Freeze off
Freeze on
Auto setup
Shutter off
Shutter on
RGB 1
RGB 2
Video
S-Video
DVI
Exit test pattern
White (full on)
Black (full off)
Flag
Window
Focus
Color bar
On-screen display off
On-screen display on
POWER
FREEZE
AUTO SETUP
SHUTTER
INPUT SELECT
TEST
ON SCREEN
PON
POF
OFZ:0
OFZ:1
OAS
OSH:0
OSH:1
IIS:RG1
IIS:RG2
IIS:VID
IIS:SVD
IIS:DVI
OTS:00
OTS:01
OTS:02
OTS:03
OTS:05
OTS:07
OTS08
OOS:0
OOS:1
Adjustment mode
Item
Command: Parameter
Callback: Parameter
Description
Parameter value
Min.
Max.
PICTURE MODE
SYSTEM
DAYLIGHT
VIEW
COLOR
TINT
COLOR TEMP.
CONTRAST
BRIGHTNESS
SHARPNESS
SET DATE
SET TIME
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
VXX:DLVI0=+00000
VXX:DLVI0=+00001
VXX:DLVI0=+00002
VXX:DLVI0=+00003
VCO:p1p2p3
VTN:p1p2p3
OTE:1
OTE:2
OTE:4
OTE:10
VCN:p1p2p3
VBR:p1p2p3
VSR:p1p2p3
TSD:y1y2y3y4m1m2d1d2w
TST:h1h2m1m2s1s2
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
VXX:DLVI0=+00000
VXX:DLVI0=+00001
VXX:DLVI0=+00002
VXX:DLVI0=+00003
VCO:p1p2p3
VTN:p1p2p3
OTE:1
OTE:2
OTE:4
OTE:10
VCN:p1p2p3
VBR:p1p2p3
VSR:p1p2p3
TSD:y1y2y3y4m1m2d1d2w
TST:h1h2m1m2s1s2
Natural
Standard
Dynamic
Cinema
Graphic
Off
1
2
3
Color
Tint
Middle
High
User
Default
Contrast
Brightness
Sharpness
Date setting
Time setting
–
–
–
–
–
–
–
–
–
1
1
–
–
–
–
1
1
0
200701011
000000
–
–
–
–
–
–
–
–
–
63
63
–
–
–
–
63
63
15
203512317
235959
Cable specifications
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
PC (DTE)
Projector
NC
NC
NC
NC
NC
NC
NC
NC
As of May 2007
< 11 >
Status asking commands
Item
Command:Parameter
Function
Description
Callback
POWER CONDITION
FREEZE
SHUTTER
INPUT SIGNAL
TEST
ON SCREEN
PICTURE MODE
SYSTEM
DAYLIGHT
VIEW
COLOR
TINT
COLOR TEMP.
CONTRAST
BRIGHTNESS
SHARPNESS
SET RUNTIME
LAMP ON TIME
(LAMP TIMER)
LAMP SELECT
LAMP POWER
VPS SYSTEM
TMP CHECK
GET DATE
GET TIME
QPW
QFZ
QSH
QIN
QTS
QOS
QPM
QVX:DLVI0
QVC
QVT
QTE
QVR
QVB
QVS
QST
Q$L:1
Q$L:2
QSL
QLP
QVY
QTM:0
QTM:1
QTM:2
QGD
QGT
Main power status
Freeze function status
Shutter function status
Input signal status
Test pattern status
On-screen display status
Picture mode status
System daylight view status
Color adjustment value
Tint adjustent value
Color temperature adjustment status
Contrast adjustment value
Brightness adjustment value
Sharpness adjustment value
Picture mode status
Lamp 1 run time
Lamp 2 run time
Lamp operation mode status
Lamp power mode status
VPS system status
Temperature status
Date setting status
Time setting status
Standby (Off)
On
Off
On
Off
On
RGB 1
RGB 2
Video
S-Video
DVI
Exit test pattern
White (full on)
Black (full off)
Flag
Window
Focus
Color bar
Off
On
Natural
Standard
dynamic
Cinema
Graphic
Off
1
2
3
Middle
High
User
Default
00000h–99999h
0000h–9999h
0000h–9999h
Dual
Single
Lamp 1
Lamp 2
High
Low
Slave
Master
p0 = Intake air
p1 = Exhaust air
p2 = DLP™ chip
yyyymmdd (day of week) (*2)
hhmmss (*3)
000
001
0
1
0
1
RG1
RG2
VID
SVD
DVI
0
1
2
3
5
7
8
0
1
NAT
STD
DYN
CIN
GRA
DLVI0=+00000
DLVI0=+00001
DLVI0=+00002
DLVI0=+00003
p1p2p3
p1p2p3
1
2
4
10
p1p2p3
p1p2p3
p1p2p3
p1p2p3p4p5
p1p2p3p4
p1p2p3p4
0
1
2
3
0
1
0
1
p1p2p3p4/p5p6p7p8 (*1)
y1y2y3y4m1m2d1d2w
h1h2m1m2s1s2
* 2
* 3
Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
* 1
p1p2p3p4: Celsius (°C), p5p6p7p8: Fahrenheit (°F)
Set the date and time to UTC (universal time coordinated).
As of May 2007
< 12 >
Parameter format
Parameter format
Size (Byte)
Difinition
As of May 2007
< 13 >
Notes on Projector Placement and Operation:
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
1.
Never place objects on top of the projector while it is operating.
2.
Make sure there is an unobstructed space of 500 mm or more around the projector’s exhaust
openings.
3.
Do not stack projector units directly on top of one another. If two units must be stacked for back-
up use in ordinary projection, use a method as shown below and provide ample space between the
units to ensure that exhaust heat does not accumulate near the intake opening or around the units.
Dual stacked projection of the PT-D5700/D5700L is not recommended.
4.
If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the
projector is between 0°C/32°F and 40°C/104°F *. Also make sure the projector’s intake and exhaust
openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is
not sucked into the intake openings.
*
Even when the ambient temperature near the intake opening is 40°C/104°F or lower, an accumulation of hot air inside the cabinet may
cause the protective circuit to activate and shut down the projector. Please give ample consideration to the design with regard to
ambient temperature conditions.
Operating the Projector Continuously:
1.
If the projector is to be operated continuously 24 hours a day, use the dual-lamp optical system’s alter-
nating lamp operation (lamp changer) function. The projector cannot be operated continuously 24 hours
a day in dual-lamp mode.
Allow a minimum of two hours per day of non-operation time.
2.
The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short
periods.
500 mm/19.2˝ or more
500 mm/19.2˝ or more*
500 mm/19.2˝ or more*
* Minimum distance when two units are used together.
Keep 300 mm/11.8˝ or more when a single unit is used.
Do not stack projector
units directly on top of
one another.
100 mm/
3.9˝ or more
DLP and the DLP logo are trademarks of Texas Instruments. UHM is a trademark of Matshushita Electic.
PJLink is a registered trademark, or a trademark application has been filed, in Japan, the United States, and other countries and regions.
VGA and XGA are registered trademarks of International Business Machines Corporation.
All other trademarks are the property of their respective trademark owners.
Direction of Air Intake and Exhaust
Intake
Exhaust
