Panasonic PT-VX42Z Operating Instructions Manual

Thank you for purchasing this Panasonic Product. Before operating this product, please read the instructions carefully, and save this manual ■ ■ for future use. Before using your projector, be sure to read “Read this first!” ( ■ ■ Æ pages 2 to 9). Model No. PT-VX42Z ENGLISH TQBJ0601

Read this first! Read this first! WARNING: THIS APPARATUS MUST BE EARTHED. WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. This device is not intended for use in the direct field of view at visual display workplaces. To avoid incommoding reflexions at visual display workplaces this device must not be placed in the direct field of view. The equipment is not intended for used at a video workstation in compliance BildscharbV. The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779. WARNING: Remove the plug from the mains socket when this unit is not in use for a prolonged period of time. 1. To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified 2. service personnel. Do not remove the earthing pin on the mains plug. This apparatus is equipped with a three prong earthing 3. type mains plug. This plug will only fit an earthing-type mains socket. This is a safety feature. If you are un- able to insert the plug into the mains socket, contact an electrician. Do not defeat the purpose of the earthing plug. CAUTION: To assure continued compliance, follow the attached installation instructions, which includes using the provided power cord and shielded interface cables when connecting to computer or peripheral device. Also, any unauthorized changes or modifications to this equipment will void the user’s authority to operate. Product information (for Turkey only) EEE Yönetmeliğine Uygundur. EEE Complies with Directive of Turkey. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. o The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. 7 The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. This is a device to project images onto a screen, etc., and is not intended for use as indoor lighting in a domestic environment. Directive 2009/125/EC Importer's name and address within the European Union Panasonic Marketing Europe GmbH Panasonic Testing Center Winsbergring 15, 22525 Hamburg, Germany

Read this first! CAUTION (North/Middle/South America and Taiwan) CAUTION: This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only fit a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug. Do not remove FCC NOTICE (USA) Declaration of Conformity Model Number: PT-VX42Z Trade Name: Panasonic Responsible Party: Panasonic Corporation of North America Address: Two Riverfront Plaza, Newark, NJ 07102-5490 Telephone number: (877)803-8492 E-mail: [email protected] This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To assure continued compliance, follow the attached installation instructions and do not make any unauthorized modifications. CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. •• Increase the separation between the equipment and receiver. •• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •• Consult the dealer or an experienced radio/TV technician for help. •• The user may find the booklet “Something About Interference” available from FCC local regional offices helpful. FCC Warning: To assure continued FCC emission limit compliance, follow the attached installation instructions. This includes using the provided power cord and shielded interface cables when connecting to computer or peripheral devices. Also, any unauthorized changes or modifications to this equipment could void the user's authority to operate this device. NOTIFICATION (Canada) This class B digital apparatus complies with Canadian ICES-003. WARNING: Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing •• Equipment, ANSI/NFPA 75. For permanently connected equipment, a readily accessible disconnect device shall be incorporated in the building •• installation wiring. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. •• Notice (USA only): This product has a High Intensity Discharge (HID) lamp that contains mercury. Disposal may be regulated in your •• community due to environmental considerations. For disposal or recycling information, please visit Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149.

Read this first! IMPORTANT: THE MOULDED PLUG (U.K. only) FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of13 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from an Authorised Service Center. If the fitted moulded plug is unsuitable for the mains socket in your home, then the fuse should be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket. If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician. WARNING: THIS APPLIANCE MUST BE EARTHED. IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Green - and - Yellow: Earth Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol or coloured GREEN or GREEN - AND - YELLOW. The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse. 13A250V BS1363/A HE-8 N ASA L

sible when problems occur. If the following problems occur, cut off the power supply immediately. Continued use of the projector in these conditions will result in fire or electric shock. If foreign objects or water get inside the projector, cut off the power supply. z z If the projector is dropped or the cabinet is broken, cut off the power supply. z z If you notice smoke, strange smells or noise coming from the projector, cut off the power supply. z z Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself. During a thunderstorm, do not touch the projector or the cable. Electric shocks can result. Do not do anything that might damage the power cord or the power plug. If the power cord is used while damaged, electric shocks, short-circuits or fire will result. Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it z z excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle. Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary. Insert the power plug securely into the wall outlet. If the plug is not inserted correctly, electric shocks or overheating will result. Do not use anything other than the provided power cord. z z Do not use the provided power cord for other electrical equipment. z z Do not use plugs which are damaged or wall outlets which are coming loose from the wall. z z Clean the power plug regularly to prevent it from becoming covered in dust. Failure to observe this will cause a fire. If dust builds up on the power plug, the resulting humidity can damage the insulation. z z If not using the projector for an extended period of time, pull the power plug out from the wall outlet. z z Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly. Do not handle the power plug with wet hands. Failure to observe this will result in electric shocks. Do not overload the wall outlet. If the power supply is overloaded (ex., by using too many adapters), overheating may occur and fire will result. ON USE/INSTALLATION „ „ Do not place liquid containers on top of the projector. If water spills onto the projector or gets inside it, fire or electric shocks will result. If any water gets inside the projector, contact an Authorized Service Center. Do not place the projector on soft materials such as carpets or sponge mats. Doing so will cause the projector to overheat, which can cause burns, fire or damage to the projector. Do not set up the projector in humid or dusty places or in places where the projector may come into contact with oily smoke or steam, ex. a bathroom. Using the projector under such conditions will result in fire, electric shocks or components deterioration. Com- ponents deterioration (such as ceiling mount brackets) may cause the projector which is mounted on the ceiling to fall down. Do not install this projector in a place which is not strong enough to take the full weight of the projec- tor or on top of a surface which is sloped or unstable. Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage could result. Do not place another projector or other heavy objects on top of the projector. Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or injury. The projector will be damaged or deformed. Installation work (such as ceiling mount bracket) should only be carried out by a qualified technician. If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks. Do not use anything other than an authorized ceiling mount bracket. z z Be sure to use the wire provided with the projector mount bracket for ceiling mount as an extra safety mea- z z sure to prevent the projector from falling down (Install in a different location to the ceiling mount bracket). ENGLISH - 5 Read this first!

Doing so will cause the projector to overheat, which can cause fire or damage to the projector. Do not place the projector in narrow, badly ventilated places. z z Do not place the projector on cloth or papers, as these materials could be drawn into the air intake port. z z Do not place your hands or other objects close to the air exhaust port. Doing so will cause burns or damage your hands or other objects. Heated air comes out of the air exhaust port. Do not place your hands or face, or objects which cannot z z withstand heat close to this port. Do not look and place your skin into the lights emitted from the lens while the projector is being used. Doing so can cause burns or loss of sight. Strong light is emitted from the projector’s lens. Do not look or place your hands directly into this light. z z Be especially careful not to let young children look into the lens. In addition, turn off the power and discon- z z nect the power plug when you are away from the projector. Do not insert any foreign objects into the projector. Doing so will cause fire or electric shocks. Do not insert any metal objects or flammable objects into the projector or drop them onto the projector. z z Never attempt to remodel or disassemble the projector. High voltages can cause fire or electric shocks. For any inspection, adjustment and repair work, please contact an Authorized Service Center. z z Do not project an image with the lens cap attached. Doing so can cause fire. Do not allow metal objects, flammable objects, or liquids to enter inside of the projector. Do not allow the projector to get wet. Doing so may cause short circuits or overheating, and result in fire, electric shock, or malfunction of the projec- tor. Do not place containers of liquid or metal objects near the projector. z z If liquid enters inside of the projector, consult your dealer. z z Particular attention must be paid to children. z z Use the ceiling mount bracket specified by Panasonic. Defects in the ceiling mount bracket will result in falling accidents. Attach the supplied safety cable to the ceiling mount bracket to prevent the projector from falling down. z z ACCESSORIES „ „ Do not use or handle the batteries improperly, and refer to the following. Failure to observe this will cause burns, batteries to leak, overheat, explode or catch fire. Use AAA/R03 o z z r AAA/LR03 batteries. Do not use unspecified batteries. z z Do not disassemble dry cell batteries. z z Do not heat the batteries or place them into water or fire. z z Do not allow the + and z z - terminals of the batteries to come into contact with metallic objects such as neck- laces or hairpins. Do not store or carry batteries together with metallic objects. z z Store the batteries in a plastic bag and keep them away from metallic objects. z z Make sure the polarities (+ and z z -) are correct when inserting the batteries. Do not use a new battery together with an old battery or mix different types of batteries. z z Do not use batteries with the outer cover peeling away or removed. z z Remove the empty batteries from the remote control at once. z z Insulate the battery using tape or something similar before disposal. z z Do not allow children to reach the batteries (AAA/R03 or AAA/LR03 type). The battery can cause personal injury if swallowed. z z If swallowed, seek medical advice immediately. z z If the battery fluid leaks, do not touch it with bare hands, and take the following measures if necessary. Battery fluid on your skin or clothing could result in skin inflammation or injury. z z Rinse with clean water and seek medical advice immediately. Battery fluid coming in contact with your eyes could result in loss of sight. z z In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately. 6 - ENGLISH Read this first!

If the lamp breaks, it could cause injury. Lamp replacement The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will result. The lamp can easily explode if struck against hard objects or dropped. z z Before replacing the lamp, be sure to disconnect the power plug from the wall outlet. z z Electric shocks or explosions can result if this is not done. When replacing the lamp, turn the power off and allow the lamp it to cool for at least 1 hour before handling z z it otherwise it can cause burns. Do not allow infants or pets to touch the remote control unit. Keep the remote control unit out of the reach of infants and pets after using it. z z Do not use the supplied power cord with devices other than this projector. Using the supplied power cord with devices other than this projector may cause short circuits or overheat- z z ing, and result in electric shock or fire. Remove the depleted batteries from the remote control promptly. Leaving them in the unit may result in fluid leakage, overheating, or explosion of the batteries. z z CAUTION: POWER „ „ When disconnecting the power cord, be sure to hold the power plug and power connector. If the power cord itself is pulled, the lead will become damaged, and fire, short-circuits or serious electric shocks will result. When not using the projector for an extended period of time, disconnect the power plug from the wall outlet and remove the batteries from the remote control. Disconnect the power plug from the wall outlet before carrying out any cleaning and replacing the unit. Electric shocks can result if this is not done. ON USE/INSTALLATION „ „ Do not place heavy objects on top of the projector. Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or injury. The projector will be damaged or deformed. Do not put your weight on this projector. You could fall or the projector could break, and injury will result. Be especially careful not to let young children stand or sit on the projector. z z Do not place the projector in extremely hot locations. Doing so will cause the outer casing or internal components to deteriorate, or result in fire. Take particular care in locations exposed to direct sunlight or near stoves. z z Always disconnect all cables before moving the projector. Moving the projector with cables still attached can damage the cables, which will cause fire or electric shocks to occur. Never plug headphones and earphones into VARIABLE AUDIO OUT jack. Excessive sound pressure from earphones and headphones can cause hearing loss. ACCESSORIES „ „ Do not use the old lamp unit. If used it could cause lamp explosion. If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the broken pieces. Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and which contains nearly the same amount of mercury as fluorescent lamps, and the broken pieces will cause injury. If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical z z advice immediately. Ask your dealer about replacing the lamp unit and check the inside of the projector. z z ENGLISH - 7 Read this first!

„ „ BRASIL Após o uso, as pilhas e /ou baterias deverão ser entregues ao estabelecimento comercial ou rede de assistência técnica autorizada. Cobrir os terminais positivo (+) e negativo (-) com uma fita isolante adesiva, antes de depositar numa caixa destinada para o recolhimento. O contato entre partes metálicas pode causar vazamentos, gerar calor, romper a blindagem e produzir fogo.(Fig. 1) Fig. 1 Como isolar os terminais Não desmonte, não remova o invólucro, nem amasse a bateria. O gás liberado pela bateria pode irritar a garganta, danificar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos terminais.Não incinere nem aqueça as baterias, elas não podem ficar expostas a temperaturas superiores a 100 °C (212 °F). O gás liberado pela bateria pode irritar a garganta, danificar o lacre do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos terminais provocado internamente. Evite o contato com o liquido que vazar das baterias. Caso isto ocorra, lave bem a parte afetada com bastante água. Caso haja irritação, consulte um médico. Remoção das baterias „ „ 1. Pressione a guia e levante a tampa. 2. Remova as baterias. Fita Isolante Fita Isolante To remove the battery 1. Press the guide and lift the cover. 2. Remove the batteries. 8 - ENGLISH Read this first!

United States and other countries. Macintosh and Mac, Mac OS, OS X, and Safari are trademarks of Apple Inc., registered in the United States and other f f countries. HDMI, the HDMI logo and High-Definition Multimedia Interface is a trademark or registered trademark of HDMI Licensing f f LLC. PJLink f f ™ is a trademark or pending trademark in Japan, the United States, and other countries and regions. RoomView and Crestron RoomView are registered trademarks of Crestron Electronics, Inc. Crestron Connected f f TM and Fusion RV are the trademarks of Crestron Electronics, Inc. Adobe, Adobe Flash Player and Adobe Reader are trademarks or registered trademarks of Adobe Systems Inc. in the United f f States and/or other countries. Some of the fonts used in the on-screen menu are Ricoh bitmap fonts, which are manufactured and sold by Ricoh Company, f f Ltd. Other names, company names or product names used in these operating instructions are the trademarks or registered f f trademarks of their respective holders. Please note that the operating instructions do not include the ® and ™ symbols. Illustrations in these operating instructions r r Note that illustrations of the projector and screens may differ from the ones you actually see. f f Page references r r In these instructions, references to pages are indicated as: ( f f Æ page 00). Term r r In these instructions, the “Wireless remote control unit” accessory is referred to as the “Remote control”. f f ENGLISH - 9 Read this first!

Auto Setup Function This function optimizes the image position ▶ ▶ and size by pressing the function. Wired LAN Function This function allows you to project an ▶ ▶ image on a computer as well as operate and manage the projector via network. Energy conservation achieved through the ECO function The function to reduce power consumption ▶ ▶ is installed, which is optimizing the lamp power according to the brightness of the surroundings, input signal, and video mute status. Quick Steps For details, see the corresponding pages. Set up your projector. 1. (x page 26) Connect with other devices. 2. (x page 30) Connect the power cord. 3. (x page 35) Power on. 4. (x page 37) Make initial settings. 5. (x page 20) Take this step when you power on for the first time after f f purchasing the projector. Select the input signal. 6. (x page 39) Adjust the image. 7. (x page 39)  10 - ENGLISH

Chapter 1 Preparation Precautions for use.................................................. 14 Cautions when transporting................................... 14 Cautions when installing........................................ 14 Security................................................................. 15 Disposal................................................................. 15 Cautions on use.................................................... 16 Accessories........................................................... 17 Contents of the supplied CD-ROM........................ 19 Optional accessories............................................. 19 Start-up display........................................................ 20 Initial setting (display language)............................ 20 Initial setting (projector setup)............................... 20 About your projector................................................ 21 Remote control...................................................... 21 Projector body....................................................... 22 Using the remote control......................................... 24 Inserting and Removing batteries.......................... 24 Setting Remote control ID numbers...................... 24 Chapter 2 Getting Started Setting up.................................................................. 26 Installation method................................................ 26 Parts for ceiling mount (Optional).......................... 26 Screen size and throw distance............................ 27 Adjusting adjustable feet....................................... 29 Connecting................................................................ 30 Before connecting to the projector........................ 30 Connecting example : AV equipment.................... 32 Connecting example : Computer........................... 32 Connecting example : Audio.................................. 33 Chapter 3 Basic Operations Powering on/off........................................................ 35 Connecting the power cord................................... 35 ON(G)/STANDBY(R) indicator.............................. 36 Turning On the Projector....................................... 37 Making adjustments and selections...................... 37 Powering Off the Projector.................................... 38 Projecting.................................................................. 39 Selecting the input signal...................................... 39 How to adjust the state of the image..................... 39 Basic operations by using the remote control...... 40 Using the AUTO SETUP function.......................... 40 Using the KEYSTONE button................................ 40 Switching the input signal...................................... 41 Using the FUNCTION button................................. 41 Using the FREEZE function.................................. 41 Using the AV MUTE function................................. 42 Using the P-TIMER function.................................. 42 Using the DIGITAL ZOOM function....................... 42 Controlling the volume of the speaker................... 43 Using the MUTE function...................................... 43 Chapter 4 Settings Menu Navigation....................................................... 45 Navigating through the menu................................ 45 Resetting adjustment values to the factory default................................................................. 46 Main menu............................................................. 46 Sub menu.............................................................. 47 [PICTURE] menu....................................................... 49 [PICTURE MODE]................................................. 49 [CONTRAST]......................................................... 49 [BRIGHTNESS]..................................................... 50 [COLOR]................................................................ 50 [TINT].................................................................... 50 [SHARPNESS]...................................................... 50 [COLOR TEMPERATURE].................................... 51 [IRIS]..................................................................... 51 [ADVANCED MENU]............................................. 51 [DAYLIGHT VIEW]................................................. 52 [DIGITAL CINEMA REALITY]................................ 52 [NOISE REDUCTION]........................................... 52 [TV-SYSTEM]........................................................ 53 [RGB/YPBPR]/[RGB/YCBCR]................................. 53 [POSITION] menu..................................................... 54 [REALTIME KEYSTONE]...................................... 54 [KEYSTONE]......................................................... 54 [SHIFT].................................................................. 55 [DOT CLOCK]....................................................... 55 [CLOCK PHASE]................................................... 56 [OVER SCAN]....................................................... 56 [ASPECT].............................................................. 57 [FRAME LOCK]..................................................... 58 [LANGUAGE] menu.................................................. 59 [LANGUAGE]........................................................ 59 [DISPLAY OPTION] menu ....................................... 60 [ON-SCREEN DISPLAY]....................................... 60 [HDMI SIGNAL LEVEL]......................................... 61 [CLOSED CAPTION SETTING]............................ 61 [STARTUP LOGO]................................................. 62 [AUTO SETUP SETTING]..................................... 63 [SIGNAL SEARCH]............................................... 63 [BACK COLOR]..................................................... 63 [WIDE MODE]....................................................... 63 [SXGA MODE]....................................................... 63 [P-TIMER].............................................................. 64 [OTHER FUNCTIONS].......................................... 65 [PROJECTOR SETUP] menu................................... 66 Contents Contents ENGLISH - 11 Contents Be sure to read “Read this first!” from page 2.

[PROJECTOR ID].................................................. 66 [INITIAL START UP].............................................. 67 [PROJECTION METHOD]..................................... 67 [HIGH ALTITUDE MODE]...................................... 67 [LAMP POWER].................................................... 68 [ECO MANAGEMENT].......................................... 68 [EMULATE]............................................................ 69 [FUNCTION BUTTON].......................................... 70 [AUDIO SETTING]................................................ 70 [TEST PATTERN].................................................. 72 [FILTER COUNTER]............................................. 72 [INITIALIZE ALL]................................................... 72 [SECURITY] menu.................................................... 73 [PASSWORD]........................................................ 73 [PASSWORD CHANGE]....................................... 73 [TEXT DISPLAY]................................................... 74 [TEXT CHANGE]................................................... 74 [MENU LOCK]....................................................... 74 [MENU LOCK PASSWORD]................................. 74 [CONTROL DEVICE SETUP]................................ 75 [NETWORK] menu.................................................... 76 [WIRED LAN]........................................................ 76 [NAME CHANGE].................................................. 77 [NETWORK CONTROL]....................................... 77 [AMX D. D.]........................................................... 77 [Crestron Connected(TM)]..................................... 77 [STATUS]............................................................... 78 [INITIALIZE]........................................................... 78 Network connections............................................. 79 Accessing from the Web browser.......................... 80 Chapter 5 Maintenance LAMP and WARNING Indicators............................. 94 Managing the indicated problems......................... 94 Replacement............................................................. 95 Before performing maintenance/replacement....... 95 Maintenance.......................................................... 95 Replacing the unit.................................................. 95 Attaching the Lens Cap......................................... 98 Troubleshooting....................................................... 99 Chapter 6 Appendix Technical Information............................................ 101 PJLink protocol.................................................... 101 Control commands via LAN................................. 102 Serial terminal..................................................... 104 List of compatible signals.................................... 107 Specifications......................................................... 109 Dimensions..............................................................111 Ceiling mount bracket safeguards....................... 112 Index........................................................................ 113 12 - ENGLISH Contents

This chapter describes things you need to know or check before using the projector. ENGLISH - 13

Cautions when transporting When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. Doing f f so may damage the internal parts and result in malfunctions. Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet. f f Cautions when installing Do not set up the projector outdoors. r r The projector is designed for indoor use only. f f Do not use under the following conditions. r r Places where vibration and impacts occur such as in a car or vehicle: Doing so may damage the internal parts f f and result in malfunctions. Near the exhaust of an air conditioner or near lights (studio lamps, etc.) where temperature changes greatly f f (Operating environment Æpage 110): Doing so may shorten the life of the lamp or result in deformation of the outer case and malfunctions. Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector. f f Be sure to ask a specialized technician when installing the product to a ceiling. r r This requires an optional ceiling mount bracket. Model No.: ET-PKV100H (for high ceilings), ET-PKV100S (for low ceilings), ET-PKV101B (Projector Mount Bracket). When using the projector in the elevation of below 1 400 m (4 593 r r '), make sure [HIGH ALTITUDE MODE] is set to [OFF]. Failure to do so may shorten the life of the internal parts and result in malfunctions. When using the projector in the elevation of above 1 400 m (4 593 r r ') and below 2 000 m (6 562'), make sure [HIGH ALTITUDE MODE] is set to [HIGH1]. Failure to do so may shorten the life of the internal parts and result in malfunctions. When using the projector in the elevation of above 2 000 m (6 562 r r ') and below 2 700 m (8 858') , make sure [HIGH ALTITUDE MODE] is set to [HIGH2]. Failure to do so may shorten the life of the internal parts and result in malfunctions. Do not install the projector at elevations of 2 700 m (8 858 r r ') or higher above sea level. Failure to do so may shorten the life of the internal parts and result in malfunctions. Do not tilt the projector or place it on its side. r r Do not tilt the projector body more than approximately ±40 degrees vertically or ±15 degrees horizontally. Over tilting may result in shortening the life of the components. Within 40° Within 40° Within 15° Within 15° 14 - ENGLISH Chapter 1 Preparation - Precautions for use

r r Do not stack the projectors. f f Do not block the ventilation ports (intake and exhaust) of the projector. f f Avoid heating and cooling air from the air conditioning system directly blow to the ventilation ports (intake and f f exhaust) of the projector. Do not install the projector in a confined space. f f When placing the projector in a confined space, a ventilation and/or air conditioning system is required. Exhaust heat may accumulate when the ventilation is not enough, triggering the protection circuit of the projector. Security Take safety measures against following incidents. Personal information being leaked via this product. f f Unauthorized operation of this product by a malicious third party. f f Interfering or stopping of this product by a malicious third party. f f Security instruction (Æpages 73, 89) Make your password as difficult to guess as possible. f f Change your password periodically. f f Panasonic or its affiliate company never inquires a password directly to a customer. Do not tell your password in case you f f receive such an inquiry. The connecting network must be secured by firewall or others. f f Set a password for web control and restrict the users who can log in f f . Disposal When disposing of the product, ask your local authority or dealer about the correct methods of disposal. The lamp contains mercury. When disposing of the used lamp unit, ask your nearest local authorities or dealer about proper disposal of the unit. Dispose of used batteries according to the instructions or your local disposal rule or guidelines. over 500 mm (19.69") over 1 000 mm (39.37") over 500 mm (19.69") over 200 mm (7.87") ENGLISH - 15 Chapter 1 Preparation - Precautions for use

To get a good picture quality r r Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light from indoor f f lamps from shining onto the screen. Depending on where the projector is used, heated air from an exhaust port or warm or cold air from an air conditioner can f f cause a shimmering effect on screen. Avoid use in locations where exhaust or streams of air from projector, other devices and air conditioners flow between the projector and the screen. The lens of projector is affected by the heat from the luminous source. Because of this, the focusing may not be stable right f f after the power is turned on. Focusing is stabled after projecting image for 30 minutes and longer. Do not touch the surface of the projector lens with your bare hands. r r If the surface of the projection lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen. Attach the supplied lens cap to the projection lens when you do not use the projector. LCD Panel r r The display unit of this projector comprises three LCD panels. Although an LCD panel is a product of high-precision technology, some of the pixels on the projected image may be missing or constantly lit. Please note that this is not a malfunction. Displaying a still image for a longer time may result in an after-image on the LCD panels. If this happens, display the all white screen in the test pattern for an hour or more. Optical components r r Operating the projector in an environment with high temperature or heavy exposure to dust or tobacco smoke will reduce the service life of the optical components, such as the LCD panel and polarizing plate, and may necessitate their replacement within less than one year of use. For details, consult your dealer. Lamp r r The luminous source of the projector is a mercury lamp with high internal pressure. A high pressure mercury lamp has following characteristics. The brightness of the lamp will decrease by duration of usage. f f The lamp may burst with sound or shorten life by shock or chipping. f f The life of the lamp varies greatly depending on individual specificities and usage conditions. In particular, continuous use f f over 12 hours and frequent on/off switching of the power greatly deteriorate the lamp and affect the lamp life. In rare cases, the lamp burst shortly after the projection. f f The risk of bursting increases when the lamp is used beyond its replacement cycle. Make sure to replace the lamp unit f f consistently. (“When to replace the lamp unit” (Æpage 97)) If the lamp bursts, gas contained inside of the lamp is released in a form of smoke. f f It is recommended to store replacement lamps for contingency. f f It is recommended to have authorized engineer or your dealer replace the lamp unit. f f 16 - ENGLISH Chapter 1 Preparation - Precautions for use

Wireless remote control unit <1> (N2QAYA000070) String <1> (6103504711) Power cord (TXFSX02UXRZ) CD ROM <1> (TXFQB02UFHZ) (TXFSX02UYAZ) AAA/R03 or AAA/LR03 battery <2> (for remote control unit) (TXFSX02UFEZ) VGA cable <1> (K1HY15YY0012) (TXFSX02UTRZ) Lens cap <1> (6103527222) ENGLISH - 17 Chapter 1 Preparation - Precautions for use

f f Do not use the supplied power cord for devices other than this projector. f f For lost accessories, consult your dealer. f f Store small parts in an appropriate manner, and keep them away from young children. f f Note The type and number of the power cord depend on the country in which you purchased the product. f f The model numbers of accessories are subject to change without prior notice. f f 18 - ENGLISH Chapter 1 Preparation - Precautions for use

The contents of the supplied CD-ROM are as follow. Instruction/list (PDF) Operating Instructions – Functional Manual Operating Instructions – Multi Projector Monitoring & Control Software Operating Instructions – Logo Transfer Software List of compatible projector models This is a list of projectors that are compatible with the software, and their restrictions. Software Multi Projector Monitoring & Control Software (Windows) This software allows you to monitor and control multiple projectors connected to the LAN. Logo Transfer Software (Windows) This software allows you to create original images, such as company logos to be displayed when projection starts, and transfer them to the projector. Optional accessories Options Model No. Ceiling Mount Bracket ET-PKV100H (for high ceilings), ET-PKV100S (for low ceilings) Projector Mount Bracket ET-PKV101B Replacement Lamp Unit ET-LAV300 Replacement Filter Unit ET-RFV300 Note The model numbers of optional accessories are subject to change without prior notice. f f ENGLISH - 19 Chapter 1 Preparation - Precautions for use

[PROJECTOR SETUP] menu, then the initial setting screen is displayed. Set them in accordance with circumstances. In other occasions, you can change the settings by menu operations. Initial setting (display language) Select the language to show on the screen. Press 1) asqw to select the display language. Press the button to proceed to the initial setting. 2) Initial setting (projector setup) Set each item. Press 1) as to select an item. Press 2) qw to switch the setting. [PROJECTION METHOD] ( f f Æpage 67) [HIGH ALTITUDE MODE] ( f f Æpage 67) Press the button. 3) Confirm the setting value and complete the initial setting. f f Note If you press the button on the initial setting screen, you can go back to the previous screen. f f To continue operations after completed the initial settings, refer to “Selecting the input signal” ( f f Æpage 39). 20 - ENGLISH Chapter 1 Preparation - Start-up display

Remote control Attention Do not drop the remote control. f f Avoid contact with liquids. f f Do not attempt to modify or disassemble the remote control. f f < 1 v/b> Button Turn the projector on or off. (Æpages 37, 38) Input Selection Buttons: , 2 , ,

1 Adjust the zoom. Control Panel and Indicators ( 2 Æpage 23) Lamp cover ( 3 Æpage 97) The lamp unit is located inside. Projection Lens 4 Focus ring (Front) 5 Adjust the focus. Remote control signal receiver 6 Air exhaust port 7 Speaker 8 terminal 9 Connect the supplied power cord. Rear terminals ( 10 Æpage 23) Air intake port / Air filter cover ( 11 Æpage 95) The air filter unit is inside. Adjustable feet 12 Adjust the projection angle. Security Chain Hook 13 Attaches a burglar prevention cable, etc. Note The remote control can be used within a distance of about 7 m (22.97') if pointed directly at the remote control signal f f receiver. The remote control can control at angles of up to ± 30 ° vertically and ± 30 ° horizontally, but the effective control range may be reduced. If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not f f operate correctly. You can operate the projector by reflecting the remote control signal on the screen. The operating range may differ due to f f the loss of light caused by the properties of the screen. When the remote control signal receiver is lit with a fluorescent light or other strong light source, the projector may become f f inoperative. Set the projector as far from the luminous source as possible. Projector body ■ Bottom view 1 5 6 4 2 3 7 11 9 10 12 WARNING Keep your hands and other objects away from the air exhaust port. Keep your hand and face away. f f Do not insert your finger. f f Keep heat-sensitive articles away. f f Heated air from the air exhaust port can cause burns or external damage. 13 Attention Do not block the ventilation ports (intake and exhaust) of the projector. f f 8 22 - ENGLISH Chapter 1 Preparation - About your projector

r r r r Rear terminals Attention When a LAN cable is directly connected to the projector, the network connection must be made indoors. f f terminal 1 This is the terminal to input RGB or YPBPR/YCBCR signals. terminal This is the terminal to input RGB signals. Or output the RGB / YCBCR/YPBPR signals to external monitor. terminal 3 This is the terminal to input HDMI signals. terminal 4 This is the terminal to a LAN cable for network connection. terminal 5 This is the RS‑232C compatible terminal to externally control the projector by connecting a computer.

Inserting and Removing batteries Open the cover. (Fig. 1) 1) Insert batteries and close the cover (Insert the 2) m side first.) (Fig. 2) When removing the batteries, perform the steps in reverse order. f f Setting Remote control ID numbers When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector individually using single remote control, if unique ID number is assigned to each projector. After setting the ID number of the projector, set the same ID number to the remote control. The factory default ID number of the projector is set to [ALL]. When using a single projector, press the button on the remote control. Also, you can control a projector by pressing the button on the remote control even if you do not know the projector ID. How to set Press the button on the remote control. 1) Within five seconds, press the one digit ID number set on the projector using the number (<1> - <6>) 2) buttons. If you press the button, you can control the projectors regardless of the ID number setting of the projector. f f Attention Since the ID number of the remote control can be set without the projector, do not press the button on the remote f f control carelessly. If the button is pressed and no number (<1> - <6>) buttons are pressed within five seconds, the ID number returns to its original value before the button was pressed. The ID number set on the remote control will be stored unless it is set again. However, it will be erased if the remote control f f is left with dead batteries. Set the same ID number again when the batteries are replaced. Note Set the ID number of the projector from the [PROJECTOR SETUP] menu → [PROJECTOR ID]. ( f f Æpage 66) Fig. 1 Fig. 2 24 - ENGLISH Chapter 1 Preparation - Using the remote control

This chapter describes things you need to do before using the projector such as the setup and connections. ENGLISH - 25

depending on the installation location. Mounting on the ceiling and projecting forward Setting on a desk/floor and projecting from rear (Using the translucent screen) Menu item Method Menu item Method [PROJECTION METHOD] [FRONT/CEILING] [PROJECTION METHOD] [REAR/DESK] Mounting on the ceiling and projecting from rear (Using the translucent screen) Setting on a desk/floor and projecting forward Menu item Method Menu item Method [PROJECTION METHOD] [REAR/CEILING] [PROJECTION METHOD] [FRONT/DESK] Parts for ceiling mount (Optional) You can install the projector on the ceiling by using the optional ceiling mount bracket (ET-PKV100H: for high ceiling, ET- PKV100S: for low ceiling), and the optional projector mount bracket ET-PKV101B. Use only the ceiling mount brackets specified for this projector. f f Refer to the Installation Instructions for the ceiling mount bracket when you install the bracket and the projector. f f Attention To ensure projector performance and security, installation of the ceiling mount bracket must be carried by your dealer or a f f qualified technician. 26 - ENGLISH Chapter 2 Getting Started - Setting up

Refer to the screen size and projection distances to install the projector. Image size and image position can be adjusted in accordance with the screen size and screen position. Projected image SH SW SD SH Screen L (LW/LT) Screen L (LW/LT) SW H L (LW/LT) *1 Projection distance (m) SH Image height (m) SW Image width (m) H Distance from the center of lens to the image lower end (m) SD Projected image size (m) LW : Minimum distance *1 LT : Maximum distance Attention Before installing, please read “Precautions for Use” ( f f Æ pages 14 to 19). Projection distance All measurements below are approximate and may differ slightly from the actual measurements. (Unit: m) Projection size For 4:3 aspect ratio For 16:9 aspect ratio Screen diagonal (SD) Minimum distance (LW) Maximum distance (LT) Height position (H) Minimum distance (LW) Maximum distance (LT) Height position (H) 0.76 (30") 1.0 1.3 0.05 1.1 1.4 0.04 1.02 (40") 1.4 1.7 0.06 1.5 1.8 0.05 1.27 (50") 1.7 2.1 0.08 1.9 2.3 0.06 1.52 (60") 2.1 2.5 0.09 2.3 2.8 0.08 1.78 (70") 2.5 3.0 0.11 2.7 3.2 0.09 2.03 (80") 2.8 3.4 0.12 3.1 3.7 0.10 2.29 (90") 3.2 3.8 0.14 3.5 4.1 0.11 2.54 (100") 3.5 4.2 0.15 3.8 4.6 0.13 3.05 (120") 4.2 5.1 0.18 4.6 5.5 0.15 3.81 (150") 5.3 6.4 0.23 5.8 6.9 0.19 5.08 (200") 7.1 8.5 0.31 7.7 9.2 0.25 6.35 (250") 8.8 10.6 0.38 9.6 11.0 0.31 7.62 (300") 10.6 11.0 0.46 -- -- 0.37 Note If the projection distance is 11.0 m or more, the performance of the projection lens can not be guaranteed. f f ENGLISH - 27 Chapter 2 Getting Started - Setting up

Any other projection distance can be obtained according to the screen dimensions (m) using the following calculations. The calculated distance may contain a certain error. If the screen dimensions are written as "SD", For 4:3 aspect ratio For 16:9 aspect ratio Screen height (SH) = SD(m) × 0.6 = SD(m) × 0.490 Screen width (SW) = SD(m) × 0.8 = SD(m) × 0.872 Minimum distance (LW) = 1.3956 × SD(m) - 0.0241 = 1.5205 × SD(m) - 0.0241 Maximum distance (LT) = 1.6746 × SD(m) - 0.0242 = 1.8245 × SD(m) - 0.0242 28 - ENGLISH Chapter 2 Getting Started - Setting up

Lift the front of the projector and press the feet lock latches on both side of the projector. Release the feet lock latches to lock the adjustable feet and rotate the adjustable feet to a proper height and tilt. You can turn the adjustable feet to extend them. You can turn them in the opposite direction to contract them. (You can adjust the projection angle vertically.) Attention Heated air comes out of the air exhaust port while the lamp is lit. Do not touch the air exhaust port directly when you adjust f f the adjustable feet. If keystone distortion occurs on the projected image, perform [KEYSTONE] from the [POSITION] menu. ( f f Æpage 54) Note Screw up the adjustable feet, and an audible click will be heard as the limit. f f Feet lock latches Adjustable range Adjustable feet : 43.0 mm(1.693") ENGLISH - 29 Chapter 2 Getting Started - Setting up

Read carefully the instruction manual for the device to be connected. f f Turn off the power switch of the devices before connecting cables. f f Take note of the following points before connecting the cables. Failure to do so may result in malfunctions. f f - When connecting a cable to a device connected to the projector or the projector itself, touch any nearby metallic objects to eliminate static electricity from your body before performing work. - Do not use unnecessarily long cables to connect to a device connected to the projector or to the projector body. The longer the cable, the more it is susceptible to noise. Since using a cable while it is wound makes it act like an antenna, it is more susceptible to noise. - When connecting cables, connect GND first, then insert the connecting terminal of the connecting device in a straight manner. If any connection cable is not supplied with the device, or if no optional cable is available for connection of the device, f f prepare a necessary system connection cable to suit the device. Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture. f f In this case, a time base corrector (TBC) must be connected. The projector accepts video signals, S-video signals, YC f f BCR/YPBPR signals and analog RGB signals (synchronous signals are TTL level), and digital signal. Some computer models are not compatible with the projector. f f When using long cables to connect with each of equipment to the projector, there is a possibility that the image will not be f f output correctly unless a compensator is used. For details on what video signals the projector supports, see “List of compatible signals”. ( f f Æpages 107-108) terminal pin assignments and signal names Outside view Pin No. Signal names GND (luminance signal) GND (color signal) Luminance signal Color signal terminal pin assignments and signal names Outside view Pin No. Signal names Pin No. Signal names R/PR + 5 V G/Y GND B/PB GND — DDC data GND HD/SYNC GND VD GND DDC clock GND 30 - ENGLISH Chapter 2 Getting Started - Connecting

Outside view Pin No. Signal names Pin No. Signal names R/PR *1 +5 V G/Y *1 GND B/PB *1 — — DDC data GND HD/SYNC GND VD GND DDC clock GND *1: It is only for RGB signals when the terminal is used as the input terminal. terminal pin assignments and signal names Outside view Pin No. Signal names Pin No. Signal names T.M.D.S data 2+ T.M.D.S clock shield T.M.D.S data 2 shield T.M.D.S clock - T.M.D.S data 2- CEC T.M.D.S data 1+ — T.M.D.S data 1 shield SCL T.M.D.S data 1- SDA T.M.D.S data 0+ DDC/CEC GND T.M.D.S data 0 shield +5 V T.M.D.S data 0- Hot plug detection T.M.D.S clock + Odd-numbered pins to Even-numbered pins to ENGLISH - 31 Chapter 2 Getting Started - Connecting

For /

f f commercially available shielded cables. Note If you operate the projector using the computer with the resume feature (last memory), you may have to reset the resume f f feature to operate the projector. Connecting example : Audio Note If the [AUDIO IN SELECT] settings are incorrect, the projector may have malfunctions such as the absence of audio. ( f f Æpage 70) When the terminal is connected with cable, the sound will not be output from the built-in speaker. f f Computer Computer Computer AV equipment Audio equipment MIC ENGLISH - 33 Chapter 2 Getting Started - Connecting

Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily. For details of power cord handling, refer to “Read this first!” (Æpage 5). Attaching Check the shapes of the terminal on the back of the projector body and the power cord 1) connector and insert the plug completely in the correct direction (until you hear the side tabs click in place). Removing Turn off the projector, and then remove the AC power cord from the electrical outlet. 1) Remove the AC power cord connector from the terminal on the projector while pressing the 2) tabs on its sides. ENGLISH - 35 Chapter 3 Basic Operations - Powering on/off

indicator before operating the projector. ON(G)/STANDBY(R) indicator Indicator status Status Off The power cord is unplugged. Red Lit The power cord is plugged. The [STANDBY MODE] is set to [ECO] when the projector is in standby mode and the cooling is completed. Blinking The power is switched off (in standby mode). The [STANDBY MODE] is set to [NETWORK].*1 The power is switched off (in standby mode). The [STANDBY MODE] is set to [NORMAL].*2 Orange Lit The projector is cooling down. The power is switched off after a while. (Changes to the standby mode.) Green Lit Projecting. Blinking The power is on and the lamp is not working. The [POWER MANAGEMENT] is set to [READY].*3 The lamp starts work. The projector will project image after a while.*4 *1: The indicator will light as the following order: 2.75 seconds (light) → 0.25 seconds (off) → 0.75 seconds (light) → 0.25 seconds (off) *2: The indicator will light as the following order: 2.75 seconds (light) → 0.25 seconds (off) *3: The indicator will light as the following order: 2.0 seconds (light) → 2.0 seconds (off) *4: The indicator will light as the following order: 0.5 seconds (light) → 0.5 seconds (off) 36 - ENGLISH Chapter 3 Basic Operations - Powering on/off

1) Connect the power plug to an outlet. 2) The indicator will light in red / green, and the projector enters the standby mode. f f Press the < 3) v/b> button on the control panel or on the remote control. The indicator lights in green and the image is soon projected on the screen. f f Attention Using the projector while the lens cap is attached may cause the device to heat up and result in a fire. f f Note If the [PROJECTOR SETUP] menu → f f [ECO MANAGEMENT] menu → [STANDBY MODE] is set to [ECO], it may take approx. 10 seconds longer before the projector starts projecting after the power is turned on, compared with when [NORMAL] is set. Making adjustments and selections It is recommended that images are projected continuously for at least 30 minutes before the focus is adjusted. 3) 5) 3) Adjust the focus of the image roughly. 1) (Æ page 39) Change the settings of the [PROJECTOR SETUP] menu → [PROJECTION METHOD] depending on the 2) installation mode. (Æ page 26) Refer to “Navigating through the menu” ( f f Æ page 45) for the operation of the menu screen. Press the button on the control panel or the input selection (, 3) , ,

1) 2) 3) 1) 2) 2) 2) Press the < 1) v/b> button on the control panel or on the remote control. The following message appears. f f Press 2) qw to select [OK], and press the button. OR Press the button on the control panel or on the remote control again. Projection of the image will stop, and the power indicator lights in orange. (The fan keeps f f running.) Wait until the indicator lights/blinks in red/green 3) . The projector enters standby mode when the indicator lights/blinks in red/green. f f Note Do not put the projector in a case before the projector is cooled enough. f f While the indicator is lighting f f in orange, the lamp is being cooled down and the projector cannot be turned on. Wait until the indicator stops lighting/blinking in red to turn on the projector again. Direct Power Off function You can disconnect the power cord from the wall outlet or turn off the breaker even during projection. Note When using the Direct Power Off function, you cannot restart the projector immediately after the power is disconnected. The f f lamp remains high temperature and needs to be cooled, so it sometimes takes longer time than usual for the lamp to light up again. 38 - ENGLISH Chapter 3 Basic Operations - Powering on/off

(Æpage 37) to start the projector. Select the image and adjust the state of the image. Selecting the input signal Select an input signal. Press the , , ,

Using the AUTO SETUP function The automatic setup function can be used to automatically adjust the resolution, clock phase, and image position when analog RGB signals consisting of bitmap images such as computer signals are being input. Supplying images with bright white borders at the edges and high-contrast black and white characters is recommended when the system is in automatic adjustment mode. Avoid supplying images that include halftones or gradation, such as photographs and computer graphics. button Press the button on the remote control. 1) Note The [CLOCK PHASE] may shift even if it has completed without any incident. In such cases, adjust the [POSITION] menu → f f [CLOCK PHASE] (Æ page 56). Automatic adjustment may not work depending on the the model of the computer and the signal. f f Images may be disrupted for a few seconds during automatic adjustment, but it is not a malfunction. f f If you press any button on the remote control during automatic adjustment, the automatic adjustment will be canceled. f f If the automatic setup function is used while moving images are being input, the adjustment may not be performed properly f f even for an RGB signal that can use automatic setup. Using the KEYSTONE button If [REALTIME KEYSTONE] is set to [ON] or the projected image still has trapezoidal distortion after pressing the button, please correct the image manually. button Press the 1) button on the remote control. The [KEYSTONE] individual adjustment screen is displayed. f f Press 2) qw to adjust. Note For more details, refer to the [POSITION] menu → [KEYSTONE] ( f f Æpage 54). 40 - ENGLISH Chapter 3 Basic Operations - Basic operations by using the remote control

You can switch the input signals to project. buttons Press the ,, ,

If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible to turn off the audio and video temporarily. button Press the button on the remote control. 1) The audio and video turn off. f f Press the button again. 2) The audio and video turn on. f f Note When [MIC] is set to [ON], the audio of MIC will output even during AV MUTE. f f Using the P-TIMER function You can operate the P-TIMER function. When you press the button on the remote control, the projector displays either a remaining time or a elapsed time. button Press the button on the remote control. 1) The count time starts. f f Remaining time or elapsed time is displayed in the lower right corner of the projected image. f f Press the button again. 2) The count time stops. f f Press the button again. 3) You can restarts the count. f f Note Pressing the button for at least three seconds releases the P-TIMER function. f f For details, please refer to [DISPLAY OPTION] -> [P-TIMER]. ( f f Æpage 64) Using the DIGITAL ZOOM function (Only for still image-based computer (RGB) and still image-based HDMI signals input) You can enlarge the center area. You can also change the location of the area to be enlarged. buttons Press the or button on the remote control. 1) The moving screen is displayed. f f The [DIGITAL ZOOM] individual adjustment screen is displayed when executing the menu operation. For details, refer f f to [DISPLAY OPTION] → [OTHER FUNCTIONS] (Æpage 65). Pressing the button cancels the function. f f Button functions during DIGITAL ZOOM r r Operation menu Operation Adjustment Adjustment range Press the button or w button. Increases magnification. 1.0 ~ 3.0 Press the button or q button. Decreases magnification. 42 - ENGLISH Chapter 3 Basic Operations - Basic operations by using the remote control

r r Operation menu Operation Adjustment Press the as buttons. Moves the area to the top or the bottom. Press the qw buttons. Moves the area to the left or the right. When you have executed the operation of remote control directly, the individual adjustment screen is not be displayed f f and the operation menu of the moving screen is displayed. At this time, you can adjust the magnification by using the or button on the remote control. ABC ABC ABC ABC ABC Note Magnification can be set from 1.0x to 3.0x in 0.1 increments. f f When press the button during [DIGITAL ZOOM], the DIGITAL ZOOM function will be cancelled. f f When the input signals change during [DIGITAL ZOOM], the DIGITAL ZOOM function will be cancelled. f f When [DIGITAL ZOOM] is active, the FREEZE function is not available. f f Controlling the volume of the speaker You can control the volume of the projector’s speaker or audio output. buttons Press the or button on the remote control. 1) This operation can be also performed using the f f qw buttons on the control panel. Increases the volume. Decreases the volume. Note For details, refer to [VOLUME] of [AUDIO SETTING] in the [PROJECTOR SETUP] menu ( f f Æpage 70). Using the MUTE function This function allows you to turn off the audio output temporarily. button Press the button on the remote control. 1) The audio turns off. f f Press the button again. 2) The audio turns on. f f ENGLISH - 43 Chapter 3 Basic Operations - Basic operations by using the remote control

This chapter describes the settings and adjustments you can make using the on-screen menu. 44 - ENGLISH

Navigating through the menu Operating procedure button Press the button on the remote control or the control panel. 1) The main menu screen appears. f f Press 2) as to select an item from the main menu. The selected item is highlighted in yellow. f f Press the button. 3) The submenu appears so that you can select the sub-menu item. f f Press 4) as to select the desired sub-menu item, press qw or the button to set or adjust settings. Some items will switch in order as follows each time you press f f qw. A B C For some items, press f f qw to display an individual adjustment screen with a bar scale as shown below. ENGLISH - 45 Chapter 4 Settings - Menu Navigation

f f Some items may not be adjusted or used for certain signal formats to be input to the projector. The menu items that cannot f f be adjusted or used are shown in gray characters, and they cannot be selected. [DIGITAL CINEMA REALITY] and [FRAME LOCK] may not be displayed depending on the input signal. Some items can be adjusted even if signals are not input. f f Individual adjustment screen is cleared automatically if no operation is performed for approximately five seconds. f f For menu items, refer to “Main menu” ( f f Æpage 46) and “Sub-menu” (Æpage 47). Resetting adjustment values to the factory default If the button on the remote control is pressed, the values adjusted in the menu items are restored to the factory default settings. button Press the button on the remote control. 1) Note You cannot reset all the settings to the factory default at a time. f f To reset all the settings adjusted in the sub-menu item to the factory default one at a time, execute [PROJECTOR SETUP] f f menu → [INITIALIZE ALL] (Æ page 72). Some items cannot be reset by pressing the button. Adjust each item manually. f f Main menu The main menu consists of the following 7 menu items. When a main menu item is selected, the screen changes to a submenu selection screen. Main-menu item Page [PICTURE] 49 [POSITION] 54 [LANGUAGE] 59 [DISPLAY OPTION] 60 [PROJECTOR SETUP] 66 [SECURITY] 73 [NETWORK] 76 46 - ENGLISH Chapter 4 Settings - Menu Navigation

PICTURE [ ] Sub-menu item Factory default Page [PICTURE MODE] [STANDARD]*1 49 [CONTRAST] [0] 49 [BRIGHTNESS] [0] 50 [COLOR]*2 [0] 50 [TINT]*2 [0] 50 [SHARPNESS] [8] 50 [COLOR TEMPERATURE] [DEFAULT] 51 [IRIS] [OFF]*1 51 [ADVANCED MENU] - 51 [DAYLIGHT VIEW] [AUTO] 51 [DIGITAL CINEMA REALITY] [ON] 52 [NOISE REDUCTION]*3 [OFF] 52 [TV-SYSTEM]*3 [AUTO] 52 [RGB/YPBPR]/[RGB/YCBCR]*4 [AUTO] 53 It will be different depending on the input signal. *1 Only for movie-based signals. *2 Only when the /

] Sub-menu item Factory default Page [STATUS] - 66 [COMPUTER2 SELECT] [COMPUTER2 IN] 66 [PROJECTOR ID] [ALL] 66 [INITIAL START UP] [LAST MEMORY] 67 [PROJECTION METHOD] [FRONT/DESK] 67 [HIGH ALTITUDE MODE] [OFF] 67 [LAMP POWER] [NORMAL] 68 [ECO MANAGEMENT] - 68 [EMULATE] [DEFAULT] 69 [FUNCTION BUTTON] - 70 [AUDIO SETTING] - 70 [TEST PATTERN] - 72 [FILTER COUNTER] - 72 [INITIALIZE ALL] - 72 SECURITY [ ] Sub-menu item Factory Default Page [PASSWORD] [OFF] 73 [PASSWORD CHANGE] - 73 [TEXT DISPLAY] [OFF] 74 [TEXT CHANGE] - 74 [MENU LOCK] [OFF] 74 [MENU LOCK PASSWORD] - 74 [CONTROL DEVICE SETUP] - 75 NETWORK [ ] Sub-menu item Factory default Page [WIRED LAN] [-] 76 [NAME CHANGE] [-] 77 [NETWORK CONTROL] [ON] 77 [AMX D. D.] [OFF] 77 [Crestron Connected(TM)] [OFF] 77 [STATUS] [-] 78 [INITIALIZE] [-] 78 Note Some items may not be adjusted or used for certain signal formats to be input to the projector. f f The menu items that cannot be adjusted or used are shown in gray characters, and they cannot be selected. f f Sub-menu items and factory default settings differ depending on the selected input terminal. f f 48 - ENGLISH Chapter 4 Settings - Menu Navigation

Refer to "Navigating through the menu" (xpage 45) for the operation of the menu screen. After selecting the item, press asqw to set. [PICTURE MODE] You can switch to the desired picture mode suitable for the image source and the environment in which the projector is used. Press 1) as to select [PICTURE MODE]. Press 2) qw or the button. The [PICTURE MODE] individual adjustment screen is displayed. f f Press 3) qw to switch the item. The items will switch each time you press the button. f f [STANDARD] The picture becomes suitable for moving images in general. [DYNAMIC] The light output is maximized for use in bright areas. [BLACKBOARD] The picture becomes suitable for projecting on a black board. [WHITE BOARD] The picture becomes suitable for projecting on a white board. [CINEMA]*1 The picture becomes suitable for movie sources. [NATURAL]*2 The picture complies with sRGB. Only for the movie-based signals. *1 Only for the still image signals. *2 Note The factory default picture mode is [DYNAMIC] for still image input signals and [STANDARD] for movie-based input signals. f f sRGB is an international standard (IEC61966‑2‑1) for color reproduction defined by IEC (International Electrotechnical f f Commission). [CONTRAST] You can adjust the contrast of the colors. Press 1) as to select [CONTRAST]. Press 2) qw or the button. The [CONTRAST] individual adjustment screen is displayed. f f Press 3) qw to adjust the level. Operation Adjustment Adjustment range Press the ► button. Brightens the screen and makes the color deeper. -32 ~ +32 Press the ◄ button. Darkens the screen and makes the color lighter. Attention Adjust [BRIGHTNESS] first when you need to adjust [BRIGHTNESS] and [CONTRAST]. f f ENGLISH - 49 Chapter 4 Settings - [PICTURE] menu

Press 1) as to select [BRIGHTNESS]. Press 2) qw or the button. The [BRIGHTNESS] individual adjustment screen is displayed. f f Press 3) qw to adjust the level. Operation Adjustment Adjustment range Press the ► button. Increases the brightness of the dark (black) parts of the screen. -32 ~ +32 Press the ◄ button. Reduces the brightness of the dark (black) parts of the screen. [COLOR] (Only for movie-based signal input) You can adjust the color saturation of the projected image. Press 1) as to select [COLOR]. Press 2) qw or the button. The [COLOR] individual adjustment screen is displayed. f f Press 3) qw to adjust the level. Operation Adjustment Adjustment range Press the ► button. Deepens colors. -32 ~ +32 Press the ◄ button. Weakens colors. [TINT] (When input movie-based signal to the /

Press 1) as to select [COLOR TEMPERATURE]. Press 2) qw or the button. The [COLOR TEMPERATURE] individual adjustment screen is displayed. f f Press 3) qw to switch the item. The items will switch each time you press the button. f f [DEFAULT] Factory default setting. [HIGH] Selects the suitable natural color. [LOW] [IRIS] Aperture correction and signal compensation are performed automatically based on the image to result in an image of optimum contrast. Press 1) as to select [IRIS]. Press 2) qw or the button. The [IRIS] individual adjustment screen is displayed. f f Press 3) qw to switch the item. The items will switch each time you press the button. f f [OFF] No correction. [ON] Corrects the aperture. [ADVANCED MENU] You can performed more advanced image adjustment. Press 1) as to select [ADVANCED MENU]. Press the button. 2) The [ADVANCED MENU] screen is displayed. f f Press 3) as to select one item among [CONTRAST R] ~ [BRIGHTNESS B]. Press 4) qw or the button. The individual adjustment screen of items are displayed. f f Press 5) qw to adjust the value. Items Operation Adjustment Adjustment range [CONTRAST R] Press the w button. Emphasizes red in highlight areas. -32 ~ +32 Press the q button. Deemphasizes red in highlight areas. [CONTRAST G] Press the w button. Emphasizes green in highlight areas. -32 ~ +32 Press the q button. Deemphasizes green in highlight areas. [CONTRAST B] Press the w button. Emphasizes blue in highlight areas. -32 ~ +32 Press the q button. Deemphasizes blue in highlight areas. [BRIGHTNESS R] Press the w button. Emphasizes red in shadow areas. -32 ~ +32 Press the q button. Deemphasizes red in shadow areas. [BRIGHTNESS G] Press the w button. Emphasizes green in shadow areas. -32 ~ +32 Press the q button. Deemphasizes green in shadow areas. [BRIGHTNESS B] Press the w button. Emphasizes blue in shadow areas. -32 ~ +32 Press the q button. Deemphasizes blue in shadow areas. ENGLISH - 51 Chapter 4 Settings - [PICTURE] menu

Press 1) as to select [DAYLIGHT VIEW]. Press 2) qw or the button. The [DAYLIGHT VIEW] individual adjustment screen is displayed. f f Press 3) qw to switch the item. The items will switch each time you press the button. f f [AUTO] Enables auto correction of [DAYLIGHT VIEW]. The luminance sensor detects the brightness and color of the surroundings and automatically corrects the video display. [ON] Enables [DAYLIGHT VIEW]. [OFF] Disables [DAYLIGHT VIEW]. Note [DAYLIGHT VIEW] can not be set to [AUTO] when the [PROJECTOR SETUP] menu → [PROJECTION METHOD] is set to f f [REAR/DESK] or [REAR/CEILING]. The [AUTO] mode may not function properly if an object is placed on the top of the projector. f f [DIGITAL CINEMA REALITY] (Only for movie-based signal) You can improve the vertical resolution of 2-2 and 2-3 pulldown video. This function is available only with the following signal inputs. 525i (480i), 625i (576i), 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24sF, S-VIDEO signal, VIDEO signal. Press 1) as to select [DIGITAL CINEMA REALITY]. Press 2) qw or the button. The [DIGITAL CINEMA REALITY] individual adjustment screen is displayed. f f Press 3) qw to switch the item. The items will switch each time you press the button. f f [ON] Enables [DIGITAL CINEMA REALITY]. [OFF] Disables [DIGITAL CINEMA REALITY]. [NOISE REDUCTION] (Only when the /

The projector will automatically detect the input signal, but you can set the color system manually when an unstable signal is input. Set the color system matching the input signal. Press 1) as to select [TV-SYSTEM]. Press 2) qw or the button. The [TV-SYSTEM] individual adjustment screen is displayed. f f Press 3) qw to select the color system. The items will switch each time you press the button. f f Select among [AUTO], [NTSC], [NTSC4.43], [PAL], [PAL-M], [PAL-N], [PAL60] and [SECAM]. f f Set it to [AUTO] normally. (Setting [AUTO] will automatically select [NTSC], [NTSC4.43], [PAL], [PAL-M], [PAL-N], f f [SECAM] or [PAL60]. [RGB/YPBPR]/[RGB/YCBCR] Set it to [AUTO] normally. If images are not displayed correctly when this is set to [AUTO], set either [RGB] or [YCBCR], [YPBPR] in accordance with the input signal. Press 1) as to select [RGB/YPBPR] or [RGB/YCBCR]. Press 2) qw or the button. The [RGB/YP f f BPR] or [RGB/YCBCR] individual adjustment screen is displayed. Press 3) qw to switch the item. The items will switch each time you press the button. f f [AUTO] The sync signal automatically selects the signal [RGB]/ [YPBPR]/[YCBCR]. [RGB] Select it for RGB signal input. [YPBPR] Select it for YPBPR signal input. [YCBCR] Select it for YCBCR signal input. When the terminal is selected For 525i (480i), 625i (576i), 525p (480p) and 625p (576p) input f f Select [AUTO], [RGB] or [YCBCR]. For other movie-based signal input f f Select [AUTO], [RGB] or [YPBPR]. When the terminal is selected For 525p (480p) and 625p (576p) input f f Select [AUTO], [RGB] or [YCBCR]. For other movie-based signal input f f Select [AUTO], [RGB] or [YPBPR]. Note Refer to “List of compatible signals” ( f f Æ pages 107-108) for the signal details. The signal selection may not function properly depending on connected devices. f f ENGLISH - 53 Chapter 4 Settings - [PICTURE] menu

Refer to "Navigating through the menu" (Æpage 45) for the operation of the menu screen. After selecting the item, press f f asqw to set. [REALTIME KEYSTONE] The projector can correct the vertical trapezoidal distortion automatically when the projector is installed tilted. Press 1) as to select [REALTIME KEYSTONE]. Press 2) qw or the button. [REALTIME KEYSTONE] individual adjustment screen is displayed. f f Press 3) qw to switch the item. The items will switch each time you press the button f f . [OFF] Set this function to off. [ON] Executes vertical keystone correction automatically when the projector is installed tilted. [KEYSTONE] You can correct the trapezoidal distortion that occurs when the projector is installed tilted or when the screen is tilted. Press 1) as to select [KEYSTONE]. Press 2) qw or the button. The [KEYSTONE] individual adjustment screen is displayed. f f Press 3) qw to compensate. Operation Adjustment Adjustment range Press the q button. The bottom becomes smaller. -60 ~ +60 Press the w button. The top becomes smaller. Note The menu or logo may run off the screen when adjustments are performed with [KEYSTONE]. f f Correcting up to ±30° for the tilt in the vertical direction is available for adjustments with [KEYSTONE]. However, the image f f quality will degrade and it will get harder to focus with more correction. Install the projector so that the correction will be as small as possible. Screen size will also change when [KEYSTONE] is used to perform various adjustments. f f Aspect ratio of the image size may shift depending on the correction. f f 54 - ENGLISH Chapter 4 Settings - [POSITION] menu

Move the image position vertically or horizontally if the image position projected on the screen is shifted even when the relative position of the projector and the screen is installed correctly. Press 1) as to select [SHIFT]. Press the button. 2) The [SHIFT] screen is displayed. f f Press 3) asqw to adjust the position. Orientation Operation Adjustment Vertical (up and down) adjustment. Press the a button. The image position moves up. Press the s button. The image position moves down. Horizontal (right and left) adjustment. Press the w button. The image position moves to the right. Press the q button. The image position moves to the left. [DOT CLOCK] (Only for still image computer (RGB) signals input) Use this function to adjust and minimize the effect of interference caused by projection of patterns consisting of vertical stripes. The projection of the following striped pattern may cause cyclic patterns (noise). Adjust so that the amount of interference is at a minimum. You can adjust the dot lock of image. Press 1) as to select [DOT CLOCK]. Press 2) qw or the button. The [DOT CLOCK] individual adjustment screen is displayed. f f Press 3) qw to adjust the value. The adjustment value are -32 to +32. f f Attention Set it before adjusting [CLOCK PHASE]. f f ENGLISH - 55 Chapter 4 Settings - [POSITION] menu

You can adjust to achieve an optimal image when there is a flickering image or smeared outlines. Press 1) as to select [CLOCK PHASE]. Press 2) qw or the button. The [CLOCK PHASE] individual adjustment screen is displayed. f f Press 3) qw to adjust the value. The adjustment value are -16 to +16. Adjust so that the amount of interference is at a minimum. f f Note Certain signals may not be adjustable. f f Optimal value may not be achieved if the output from the input computer is unstable. f f To project a signal with dot clock frequency with 162 MHz or higher, noise may not disappear even if [CLOCK PHASE] is f f adjusted. [CLOCK PHASE] cannot be adjusted when a digital signal is input. f f [OVER SCAN] Use this function when characters or pictures are cropped near the periphery of the projected image. Press 1) as to select [OVER SCAN]. Press 2) qw or the button. The [OVER SCAN] individual adjustment screen is displayed. f f Press 3) qw to adjust the level. The adjustment value are 0 to +3. f f Note It is unavailable for still images signals and HDMI signals. f f 56 - ENGLISH Chapter 4 Settings - [POSITION] menu

Press 1) as to select [ASPECT]. Press 2) qw or the button. The [ASPECT] individual adjustment screen is displayed. f f Press 3) qw to switch the item. The items will switch each time you press the button. f f [NORMAL] Displays images without changing the aspect ratio of the input signals. [AUTO]*1 The aspect ratio is automatically switched to the optimum aspect ratio when an aspect ratio identifier is included in the input signal. [WIDE] Displays images with the aspect ratio converted to 16:9 when standard signals*2 are input. Display images without changing the aspect ratio when wide-screen signals*3 are input. [H FIT] While the aspect ratio is kept fixed, The image is projected using all the panel pixels horizontally, and the vertical edges of the image are cropped. [V FIT] Displays the height of the panel pixels vertically without changing the aspect ratio when wide-screen signals are input. When signals have the aspect ratio horizontally longer than the aspect ratio of the screen, the images are displayed with the right and left parts cut off. [FULL] The image is projected using all the panel (screen) pixels. The input signals are converting to the aspect ratio of the panel (screen). [NATIVE] Displays images without changing the resolution of the input signals. Only for Video (NTSC) and 480i (YC *1 BCR) signals input. Standard signals are input signals with an aspect ratio of 4:3 or 5:4. *2 Wide-screen signals are input signals with an aspect ratio of 16:10, 16:9 or 15:9. *3 Note The image size may be switched abnormally when [AUTO] is selected, please set to [NORMAL] or [WIDE] according to the f f input signal. Some size modes are not available for certain types of input signals. f f If an aspect ratio which is different from the aspect ratio for the input signals is selected, the images will appear differently f f from the originals. Be careful of this when selecting the aspect ratio. If using the projector in places such as cafes or hotels to display programs for a commercial purpose or for public f f presentation, note that adjusting the aspect ratio or using the zoom function to change the screen images may be an infringement of the rights of the original copyright owner for that program under copyright protection laws. Take care when using a function of the projector such as the aspect ratio adjustment and zoom function. If conventional (normal) 4:3 images which are not wide-screen images are displayed on a wide screen, the edges of the f f images may not be visible or they may become distorted. Such images should be viewed as with an aspect ratio of 4:3 in the original format intended by the creator of the images. ENGLISH - 57 Chapter 4 Settings - [POSITION] menu

This setting is available for specific computer signals. Set when the movie is distorted. Press 1) as to select [FRAME LOCK]. Press 2) qw or the button. The [FRAME LOCK] individual adjustment screen is displayed. f f Press 3) qw to switch the [FRAME LOCK]. The items will switch each time you press the button. f f [OFF] Disables the frame lock. [ON] Enables the frame lock. 58 - ENGLISH Chapter 4 Settings - [POSITION] menu

Refer to "Navigating through the menu" (Æpage 45) for the operation of the menu screen. Press f f as to select a language, and press button to set. [LANGUAGE] You can select the language of the on-screen display. Various menus, settings, adjustment screens, control button names, etc., are displayed in the selected language. f f The language can be changed to English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Finnish, f f Norwegian, Danish, Polish, Hungarian, Romanian, Czech, Russian, Turkish, Arabic, Kazakh, Vietnamese, Chinese, Korean, Japanese and Thai. Note The on-screen display language of the projector is set to English by default and when [INITIALIZE ALL] ( f f Æ page 72) in [PROJECTOR SETUP] is executed. ENGLISH - 59 Chapter 4 Settings - [LANGUAGE] menu

On the menu screen, select [DISPLAY OPTION] from the main menu, and select an item from the submenu. Refer to "Navigating through the menu" (Æpage 45) for the operation of the menu screen. After selecting the item, press f f asqw to set. [ON-SCREEN DISPLAY] Set the on-screen display and position. [INPUT GUIDE] Set whether to display the input guide when switching the input source. Press 1) as to select [ON-SCREEN DISPLAY]. Press the button. 2) The [ON-SCREEN DISPLAY] screen is displayed. f f Press 3) as to select [INPUT GUIDE]. Press 4) qw to switch the item. The items will switch each time you press the button. f f [DETAILED] Displays the name of input terminal and input signal graphically. [OFF] Disables the input guide. [SIMPLE] Displays the name of input terminal and input signal. [OSD POSITION] Set the position of the menu screen (OSD). Press 1) as to select [ON-SCREEN DISPLAY]. Press the button. 2) The [ON-SCREEN DISPLAY] screen is displayed. f f Press 3) as to select [OSD POSITION]. Press 4) qw to switch the item. The items will switch each time you press the button as following: f f [CENTER] → [UPPER LEFT] → [UPPER RIGHT] → [LOWER LEFT] → [LOWER RIGHT] → [CENTER] → ... [WARNING MESSAGE] Set the display/hide of the warning message. Press 1) as to select [ON-SCREEN DISPLAY]. Press the button. 2) The [ON-SCREEN DISPLAY] screen is displayed. f f 60 - ENGLISH Chapter 4 Settings - [DISPLAY OPTION] menu

Press 4) qw to switch the item. The items will switch each time you press the button. f f [ON] Displays the warning/error message. [OFF] Hides the warning/error message. [HDMI SIGNAL LEVEL] Switch the setting when the external equipment is connected to the terminal of the projector and the image is not projected correctly. Press 1) as to select [HDMI SIGNAL LEVEL]. Press the button. 2) The [HDMI SIGNAL LEVEL] screen is displayed. f f Press 3) qw to switch the item. The items will switch each time you press the button. f f [AUTO] Sets the signal level automatically. [64-940] Select when the HDMI terminal of an external device (such as a blu-ray player) is connected to the terminal. [0-1023] Select when the DVI terminal output of an external device (such as a computer) is connected to the terminal via a conversion cable or similar cable. Select also when the HDMI terminal output of a computer or other device is connected to the terminal. Note The optimal setting varies depending on the output setting of the connected external device. Refer to the operation f f instruction of the external device regarding the output of the external device. The HDMI signal level is displayed for every 30 bits of input. f f [CLOSED CAPTION SETTING] (only for NTSC, 480i YCBCR signals) Set the closed caption. Selecting the closed caption display Set the closed caption display. Press 1) as to select [CLOSED CAPTION SETTING]. Press the button. 2) The [CLOSED CAPTION SETTING] screen is displayed. f f Press 3) as to select [CLOSED CAPTION]. Press 4) qw to switch the item. The items will switch each time you press the button. f f [ON] Closed captions are displayed. [OFF] Closed captions are not displayed. When [ON] is selected, proceed to Step 5). f f When the confirmation is displayed, select [OK], and press the button. 5) Setting the closed caption mode Press 1) as to select [CLOSED CAPTION SETTING]. Press the button. 2) The [CLOSED CAPTION SETTING] screen is displayed. f f Press 3) as to select [MODE]. ENGLISH - 61 Chapter 4 Settings - [DISPLAY OPTION] menu

The items will switch each time you press the button. f f [CC1] Displays CC1 data. [CC2] Displays CC2 data. [CC3] Displays CC3 data. [CC4] Displays CC4 data. Note Closed captions are a function that is mainly used in North America to display text information with video signals. Captions f f may not be displayed depending on the connected devices or software being played back. [CLOSED CAPTION SETTING] can only be selected if an NTSC or 480i YC f f BCR signal is input. If [CLOSED CAPTION SETTING] is set to [ON], the brightness of image may be changed according to the external devices f f or the used content of the closed caption corresponding connection. If a closed caption signal of the selected mode is input, the text is not displayed even when the [SECURITY] menu → [TEXT f f DISPLAY] (Æ page 74) is set to [ON]. Closed captions are not displayed when the menu screen is displayed. f f [STARTUP LOGO] Set the logo display when the power is turned on. Press 1) as to select [STARTUP LOGO]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [DEFAULT LOGO] Displays the Panasonic logo. [USER LOGO] Displays the image registered by the user. [OFF] Disables the startup logo display. Note The startup logo will disappear in approximately f f 30 seconds. To create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM. f f If you do not register the [USER LOGO] image, the startup logo will not be displayed even if the [STARTUP LOGO] is set to f f [USER LOGO]. 62 - ENGLISH Chapter 4 Settings - [DISPLAY OPTION] menu

Set the automatic execution of AUTO SETUP. The screen display position or signal level can be adjusted automatically without pressing the button on the remote control or the control panel on each occasion if you input unregistered signals frequently at meetings, etc. Press 1) as to select [AUTO SETUP SETTING]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [AUTO] Enables the auto setup function when switching signals. [BUTTON] Enables the auto setup function only when the button is pressed. [SIGNAL SEARCH] When the power is turned on, this function automatically detects the terminal which signals are input and sets the function to switch. Press 1) as to select [SIGNAL SEARCH]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [ON] Enables input detection automatically. [OFF] Disables input detection automatically. Note If the [SIGNAL SEARCH] is set to [ON] when there is no signal input, press the button on the remote f f control or the control panel, this function automatically detects the terminal to which signals are input and then switches. [BACK COLOR] Set the display of the projected screen when there is no signal input. Press 1) as to select [BACK COLOR]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [BLUE] Displays the entire projection area in blue. [BLACK] Displays the entire projection area in black. [DEFAULT LOGO] Displays the Panasonic logo. [USER LOGO] Displays the image registered by the user. Note To create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM. f f If you do not register the image of the [USER LOGO], the projected image will be displayed in black even if the [BACK f f COLOR] is set to [USER LOGO]. [WIDE MODE] Using this function when displays the incorrect signals input. Press 1) as to select [WIDE MODE]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [AUTO] Displays by judging the signal automatically. Set to this mode normally. [OFF] When input the 4:3 signal. [ON] When input the wide signals. [SXGA MODE] This function is used if the whole projected image is not displayed when SXGA signal is input. Set it to [SXGA] normally. Press 1) as to select [SXGA MODE]. Press 2) qw to switch the item. ENGLISH - 63 Chapter 4 Settings - [DISPLAY OPTION] menu

f f [SXGA] The image will be displayed completely when it is set to [SXGA]. [SXGA +] The image will be displayed incompletely when it is set to [SXGA +]. [P-TIMER] Set and operate the presentation timer function. Press 1) as to select [P-TIMER]. Press the button. 2) The [P-TIMER] screen is displayed. f f [MODE] Switches the elapsed time between [COUNT UP] and [COUNT DOWN]. [TIMER] Sets the finish time of timer when [COUNT DOWN] is selected. [START] / [STOP] / [RESTART] Operates the timer. [RESET] Resets the count. [EXIT] [P-TIMER] is finished. Setting [MODE] Press 1) as to select [MODE]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [COUNT UP] Displays the elapsed time from count started. [COUNT DOWN] Displays the remaining time for the time in set in [TIMER] menu. Setting the countdown timer Press 1) as to select [TIMER]. Press 2) qw to set the timer. The timer can be set from 1 to 180 minutes in 1 increment. f f The factory default setting is 10 minutes. f f Note [TIMER] is available only when [MODE] is set to [COUNT DOWN]. f f The operation of [P-TIMER] Press 1) as to select [START], [STOP] or [RESTART]. [START] Starts counting. [STOP] Stops counting. [RESTART] Restarts counting. Press the button. 2) When you select [START] or [RESTART], the remaining time or the elapsed time will be displayed in the lower right of f f the projected image. When you select [STOP], the remaining time or the elapsed time while stopping the counting will be displayed in the f f lower right of the projected image. When [RESTART] is selected, then go to step 3). f f Press the button 3 times and then the menu screen will disappear. 3) The start time will be displayed in the lower right of the projected image. f f Note You can also use the P-TIMER function by pressing the button on the remote control ( f f Æ page 42). If the elapsed time or remaining time is displaying, the text will not be displayed even when the [SECURITY] menu → [TEXT f f DISPLAY] (Æ page 74) is set to [ON]. The elapsed time or remaining time will not be display when the Menu screen is displaying. f f The start time will be "000:00" when [MODE] is set to [COUNT UP]. f f 64 - ENGLISH Chapter 4 Settings - [DISPLAY OPTION] menu

f f The circle gauge for [COUNT UP] is rotated clockwise, the circle gauge for [COUNT DOWN] is rotated counter-clockwise. f f [OTHER FUNCTIONS] You can perform some of the remote control button operations from the sub-menu. Press 1) as to select [OTHER FUNCTIONS]. Press the button. 2) The [OTHER FUNCTIONS] screen is displayed. f f Press 3) as to select [AUTO SETUP], [FREEZE], [AV MUTE] or [DIGITAL ZOOM]. [AUTO SETUP] For details, refer to "Using the AUTO SETUP function" (Æpage 40). [FREEZE] The projected image is paused temporarily and the sound stopped regardless of the playback of the external equipment. To release this function, press the button or the button on the remote control. [AV MUTE] Turn off audio and video when the projector is not used for a certain period of time. To release this function, press the button or the button on the remote control. [DIGITAL ZOOM] For details, refer to "Using the DIGITAL ZOOM function" (Æpage 42). Press the button. 4) ENGLISH - 65 Chapter 4 Settings - [DISPLAY OPTION] menu

On the menu screen, select [PROJECTOR SETUP] from the main menu, and select an item from the submenu. Refer to "Navigating through the menu" (Æpage 45) for the operation of the menu screen. After selecting the item, press f f asqw to set. [STATUS] You can check the using status of the projector. Press 1) as to select [STATUS]. Press the button. 2) The [STATUS] screen is displayed. f f [SIGNAL] [NAME] Displays the name of input signal. [FREQUENCY] Displays the scanning frequency of input signal. [RUNTIME]*1 [PROJECTOR] Displays the current usage time of projector. [LAMP (ET-)] [NORMAL] [ECO1] [ECO2] Displays the operation time of lamp in each mode (NORMAL/ECO1/ ECO2). It may differ from the actual runtime under the each setting of [NORMAL]/[ECO1]/[ECO2] in [LAMP POWER] menu. And, displays the model no. of the replacement lamp unit for this projector. [SERIAL NUMBER] [PROJECTOR] Displays the serial number of the projector. The following conversion is required to calculate the rough estimate for lamp replacement. *1 Formula for lamp replacement time (rough estimate) A x 1 + B x 0.8 + C x 2/3 A : Runtime which is displayed in [STATUS] screen - [RUNTIME] - [LAMP] - [NORMAL] f f B : Runtime which is displayed in [STATUS] screen - [RUNTIME] - [LAMP] - [ECO1] f f C : Runtime which is displayed in [STATUS] screen - [RUNTIME] - [LAMP] - [ECO2] f f [COMPUTER2 SELECT] Set whether to use the terminal. Press 1) as to select [COMPUTER2 SELECT]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [COMPUTER2 IN] When input the computer signal. [COMPUTER1 OUT] Outputs the signal which have been input terminal. Note The [COMPUTER2 SELECT] will be unavailable when COMPUTER2 is selected as input source. f f [PROJECTOR ID] The projector has an ID number setting function that can be used when multiple projectors are used side by side to enable simultaneous control or individual control via a single remote control. Press 1) as to select [PROJECTOR ID]. Press the button. 2) The [PROJECTOR ID] screen is displayed. f f 66 - ENGLISH Chapter 4 Settings - [PROJECTOR SETUP] menu

Select one from [ALL], and [1] to [6]. f f [ALL] Select when controlling projectors without specifying an ID number. [1]~[6] Select when specifying an ID number to control individual projector. Press the button to set it. 4) [PROJECTOR ID] is set. f f Note The ID number can be set to [ALL], or from [1] to [6]. f f To specify an ID number for individual control, the ID number of a remote control must match the ID number of the projector. f f When the ID number is set to [ALL], the projector will operate regardless of the ID number specified during remote control or f f computer control. If multiple projectors are set up side by side with ID set to [ALL], they cannot be controlled separately from the projectors with other ID numbers. Refer to “Setting the remote control ID numbers” ( f f Æpage 24) for how to set the ID number on the remote control. [INITIAL START UP] Set the method of start up when the power cord plugged into the AC outlet. Press 1) as to select [INITIAL START UP]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [LAST MEMORY] Starts in the condition that before disconnected the power cord or turn off the breaker. [STANDBY] Starts up in the standby mode. [ON] Starts the projection immediately. [PROJECTION METHOD] Set the projection method in accordance with the installation status of the projector. Change the projection method if the screen display is upside down or inverted. Press 1) as to select [PROJECTION METHOD]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [FRONT/DESK] When installing the projector on the desk, etc. in front of the screen. [FRONT/CEILING] When installing the projector in front of the screen by using the Ceiling Mount Bracket for Projectors (optional). [REAR/DESK] When installing the projector on the desk, etc. behind the screen (with a translucent screen). [REAR/CEILING] When installing the projector behind the screen (with a translucent screen) using the Ceiling Mount Bracket for Projectors (optional). [HIGH ALTITUDE MODE] Change the setting according to the altitude in which you use the projector. Press 1) as to select [HIGH ALTITUDE MODE]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [OFF] When using the projector in the elevation of below 1 400 m. [HIGH1] When using the projector in the elevation of above 1 400 m and below 2 000 m. [HIGH2] When using the projector in the elevation of above 2 000 m and below 2 700 m. Note It is set to [OFF] when using the projector in the elevation of below 1 400 m. It is set to f f [HIGH1] when using the projector in the elevation of above 1 400 m and below 2 000 m. It is set to [HIGH2] when using the projector in the elevation of above 2 000 m and below 2 700 m. Failure to do so may shorten the life of the internal parts and result in malfunctions. Do not set the projector in the elevation of 2 700 m or above, otherwise it may shorten the life of the internal parts and result f f in malfunctions. When it is set to f f [HIGH1] or [HIGH2], the fan noise becomes louder and fan speed increases. ENGLISH - 67 Chapter 4 Settings - [PROJECTOR SETUP] menu

Press 1) as to select [LAMP POWER]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [NORMAL] Select when high luminance is required. [ECO1] Select when high luminance is not required. [ECO2] Select when high luminance is not required and the operation sound is needed more quiet. Note You can reduce power consumption and operation noise, and extend the life of the lamps by setting to f f [ECO2] rather than [ECO1], or by setting to [ECO1] rather than [NORMAL]. [ECO MANAGEMENT] This function optimizes lamp power according to the operating status to reduce power consumption. Press 1) as to select [ECO MANAGEMENT]. Press the button. 2) The [ECO MANAGEMENT] screen is displayed. f f Press 3) as to select one item. Setting [AUTO POWER SAVE] in step 3) Set whether or not to enable the three functions, [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION] and [AV MUTE DETECTION]. Note [AUTO POWER SAVE] cannot be set when the [LAMP POWER] is set to f f [ECO2]. Press 4) qw to switch the [AUTO POWER SAVE]. [ON] Enables power-saving mode. [OFF] Disables power-saving mode. Press 5) as to select one item. [AMBIENT LIGHT DETECTION] Adjusts the lamp power according to the ambient brightness. [SIGNAL DETECTION] Drops the lamp power when no signal is input. [AV MUTE DETECTION] Drops the lamp power in the AV mute mode. Press 6) qw to switch the item. The items will switch each time you press the button. f f [ON] Enables above setting. [OFF] Disables above setting. Note Lamp power cannot reduced automatically in the following cases: f f - When [LAMP POWER] is set to [ECO2]. - When the lamp lit or the setting of [LAMP POWER] is completed, etc. When [AUTO POWER SAVE] is set to [OFF], [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION] and [AV MUTE f f DETECTION] cannot be set. [AMBIENT LIGHT DETECTION] will not work correctly when placing some objects on the ambient luminance sensor. f f Setting [POWER MANAGEMENT] in step 3) Set the operation as following if there is no signal input. Press 1) as to select [POWER MANAGEMENT]. Press 2) qw to switch the item. The items will switch each time you press the button. f f 68 - ENGLISH Chapter 4 Settings - [PROJECTOR SETUP] menu

down when reaching the set time, meanwhile the projector is in the power management mode. The projection lamp will be turned on if the input signal is reconnected or any button is pressed. [SHUT DOWN] The countdown timer is displayed after 30 seconds without input signal. The projection lamp is turned off and cooled down when reached the set time, then the projector enter into standby status. [OFF] Power management function is off. Setting [TIMER] The timer can be set to 5-120 minutes. The increment is 5 minutes. Press 1) as to select [TIMER]. Press 2) qw to set the timer (5-120 MIN.). The time will switch each time you press the button. f f Setting [STANDBY MODE] in step 3) Set the power consumption during standby. Press 1) as to select [STANDBY MODE]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [ECO] Restricts some functions in the standby mode to reduce power consumption. [NETWORK] Restricts network function in the standby mode. [NORMAL] Does not restrict network function and serial communication function even in the standby mode. Note If [STANDBY MODE] is set to [ECO], you cannot use network functions when the projector is standing by. Also, you cannot f f use some RS-232C protocol commands. When set to [ECO], it may take approx. 10 seconds longer before the projector starts projecting after the power is turned on, f f compared with when [NORMAL] is set. If [STANDBY MODE] is set to [NETWORK], it takes less power consumption than it is set to [NORMAL]. f f When [STANDBY MODE] is set to [NETWORK], it will be no restriction for network function and serial communication f f function within 60 seconds when the Wake on LAN function is working. The setting of [STANDBY MODE] cannot be returned to the factory default even if the [PROJECTOR SETUP] menu → f f [INITIALIZE ALL] is executed (Æ page 72). [EMULATE] When controlling the projector on a computer via the terminal, set use of control commands on a previously purchased Panasonic projector. This allows the control software for an existing Panasonic projector to be inherited and used. Press 1) as to select [EMULATE]. Press the button. 2) The [EMULATE] screen is displayed. f f Press 3) as to switch the item. The items will switch each time you press the button. f f [DEFAULT] VX42Z series, VW340Z series, VX410Z series, RZ475 series, RZ470 series, RW430 series, RZ370 series, RW330 series [D3500] D3500 series [D4000] D4000 series [D/W5k SERIES] D5700 series, DW5100 series, D5600 series, DW5000 series, D5500 series [D/W/Z6k SERIES] DZ770 series, DW740 series, DX810 series, DZ680 series, DW640 series, DX610 series, DW730 series, DX800 series, DZ6710 series, DZ6700 series, DW6300 series, D6000 series, D5000 series, DZ570 series, DW530 series, DX500 series [L730 SERIES] L730 series, L720 series, L520 series [L780 SERIES] L780 series, L750 series [L735 SERIES] L735 series [L785 SERIES] L785 series [F/W SERIES] FW430series, FX400 series, FW300 series, F300 series, F200 series, FW100 series, F100 series [LZ370] LZ370 series [LB/W SERIES] LB3 series, LB2 series, LB1 series, ST10 series, LB90 series, LW80NT series, LB80 series, LB78 series, LB75 series ENGLISH - 69 Chapter 4 Settings - [PROJECTOR SETUP] menu

VX400NT series, VX400 series, VX41 series [EZ570 SERIES] EZ570 series, EW630 series, EW530 series, EX600 series, EX500 series [VW431D] VW431D series Press the button. 4) [FUNCTION BUTTON] The function assigned to the button of the remote control is displayed. You can also release the assigned setting. Releasing assigned function to the button Press 1) as to select [FUNCTION BUTTON]. Press the button. 2) The [FUNCTION BUTTON] screen is displayed. f f Select [DISABLE], then press 3) the button. When the confirmation message is displayed, select [OK] and press the button. 4) Note You can also cancel the assigned settings by displaying the on-screen menu, selecting the menu item to be canceled (main f f menu, submenu, or details menu), and then pressing the button for at least 3 seconds. [AUDIO SETTING] You can perform more detailed setting for Audio. Adjusting the volume Press 1) as to select [AUDIO SETTING]. Press the button. 2) The [AUDIO SETTING] screen is displayed. f f Press 3) as to select [VOLUME]. Press 4) qw to adjust the level. Operation Adjustment Range Press the w button. Turns up the volume. 0 ~ 63 Press the q button. Turns down the volume. Setting the mute Press 1) as to select [AUDIO SETTING]. Press the button. 2) The [AUDIO SETTING] screen is displayed. f f Press 3) as to select [MUTE]. Press 4) qw to switch the item. [ON] Turns off the volume temporarily. [OFF] Output the audio. Setting the audio output during standby Press 1) as to select [AUDIO SETTING]. Press the button. 2) The [AUDIO SETTING] screen is displayed. f f Press 3) as to select [IN STANDBY MODE]. Press 4) qw to switch [IN STANDBY MODE]. 70 - ENGLISH Chapter 4 Settings - [PROJECTOR SETUP] menu

f f [OFF] Disables audio output in the standby mode. [ON] Enables audio output in the standby mode when [STANDBY MODE] is set to [NORMAL]. At this time, press the buttons on the remote control or qw buttons on the control panel to adjust the volume. Note Audio cannot be output during standby when [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO] f f or [NETWORK] (Æpage 69). Setting audio input selection Choose the audio input terminal for each input signal. Press 1) as to select [AUDIO SETTING]. Press the button. 2) The [AUDIO SETTING] screen is displayed. f f Press 3) as to select one item of [AUDIO IN SELECT]. [COMPUTER1] Set the audio output when [COMPUTER1] input is selected. [COMPUTER2] Set the audio output when [COMPUTER2] input is selected. [VIDEO] Set the audio output when [VIDEO] input is selected. [S-VIDEO] Set the audio output when [S-VIDEO] input is selected. [HDMI] Set the audio output when [HDMI] input is selected. Press 4) qw to switch the item. The sub items will switch each time you press the button. f f [COMPUTER1] Select one item among [AUDIO IN 1], [AUDIO IN 2] or [AUDIO IN 3]. [COMPUTER2] Select one item among [AUDIO IN 1], [AUDIO IN 2] or [AUDIO IN 3]. [VIDEO] Select one item among [AUDIO IN 1], [AUDIO IN 2] or [AUDIO IN 3]. [S-VIDEO] Select one item among [AUDIO IN 1], [AUDIO IN 2] or [AUDIO IN 3]. [HDMI] Select one item among [HDMI AUDIO IN], [AUDIO IN 1], [AUDIO IN 2] or [AUDIO IN 3]. Note When [MIC] is set to [ON], [AUDIO IN 2] cannot be selected. f f Even if [AUDIO IN 2] is selected, it will change to [AUDIO IN 1] automatically when [MIC] is set to [ON]. f f Using MIC function Press 1) as to select [AUDIO SETTING]. Press the button. 2) The [AUDIO SETTING] screen is displayed. f f Press 3) as to select [MIC]. Press 4) qw to switch the items. The items will switch each time you press the button. f f [ON]

Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before performing various adjustments. Press 1) as to select [TEST PATTERN]. Press the button. 2) The [TEST PATTERN] screen is displayed. f f Press 3) qw to switch the items. The items will switch each time you press the button. f f ALL WHITE → COLOR BARS → WHITE CROSS ON BLACK BACKGROUND → BLACK CROSS ON THE WHITE BACKGROUND → CROSS HATCH → ALL WHITE... When you press the button or button, it will display the sub menu of [PROJECTOR SETUP]. f f Note The initial setting is ALL WHITE. The initial screen is CROSS HATCH if you have assigned it to the button. f f [FILTER COUNTER] This function is used to reset the filter use time and set the notification display. Press 1) as to select [FILTER COUNTER]. Press the button. 2) The [FILTER COUNTER] screen is displayed. f f [FILTER COUNTER] Displays the using time of the filter. [TIMER] Sets the timer when you want to display an alert message of filter replacement. [FILTER COUNTER RESET] Resets the filter counter. Setting [TIMER] Press 1) as to select [TIMER]. Press 2) qw to switch the setting of the timer. The items will switch each time you press the button. f f [OFF] → [1000 H] → [2000 H] → [3000 H] → [4000 H] → [5000 H] → [6000 H] [FILTER COUNTER RESET] Press 1) as to select [FILTER COUNTER RESET]. The [FILTER COUNTER RESET] screen is displayed. z z Press the button. 2) When the confirmation is displayed, press 3) qw to select [OK] and then press the button. [INITIALIZE ALL] Return various setting values to their factory default settings. Press 1) as to select [INITIALIZE ALL]. The [INITIALIZE ALL] screen is displayed. z z Press the button. 2) When the confirmation is displayed, press 3) qw to select [OK] and then press the button. The [POWER OFF] screen is displayed. z z Press the button. 4) The operation is disabled except for turning off the power. z z Note The projector will enter into the standby status to reflect the setting values when [INITIALIZE ALL] is executed. f f 72 - ENGLISH Chapter 4 Settings - [PROJECTOR SETUP] menu

Refer to "Navigating through the menu" (Æpage 45) for the operation of the menu screen. When the projector is used for the first time Initial password: Press f f awsqawsq in order, and press the button. After selecting the item, press f f asqw to set. Attention When you select the [SECURITY] menu and press the button, entering a password is required. Enter the preset f f password and then continue operations of the [SECURITY] menu. When the password has been changed previously, enter the changed password, and press the button. f f Note The entered password is displayed with " f f " mark on the screen. An error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password. f f [PASSWORD] The [PASSWORD] screen is displayed when the power is turned on, [INITIALIZE ALL] is executed or [INITIALIZE] in the [NETWORK] is executed. When the entered password is incorrect, the operation will be restricted to the power standby button on the control panel or the remote control. Press 1) as to select [PASSWORD]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [OFF] Disables the security password entry. [ON] Enables the security password entry. Note The [PASSWORD] setting is set to [OFF] by the factory default. f f Change the password periodically that is hard to guess. f f The security password is enabled after setting [PASSWORD] to [ON] and turning the power off. f f [PASSWORD CHANGE] Change the security password. Press 1) as to select [PASSWORD CHANGE]. Press the button. 2) The [PASSWORD CHANGE] screen is displayed. f f Press 3) asqw or number buttons (<1>-<6>) to set the password. Up to eight button operations can be set. f f Press the button. 4) Re-enter the password for the confirmation. 5) Press the button. 6) ENGLISH - 73 Chapter 4 Settings - [SECURITY] menu

f f " mark on the screen. An error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password. f f If numbers have been used for the security password, the security password will need to be initialized again if the remote f f control is lost. Consult your dealer for the initialization method. [TEXT DISPLAY] Overlap the security message (text or image) over the projecting image. Press 1) as to select [TEXT DISPLAY]. Press 2) qw to switch the items. The items will switch each time you press the button. f f [OFF] Disables the text display. [ON] Enables the text display. [TEXT CHANGE] Change the text displayed when the text display is enabled by selecting [ON] in [TEXT DISPLAY]. Press 1) as to select [TEXT CHANGE]. Press the button. 2) The [TEXT CHANGE] screen is displayed. f f Press 3) asqw to select the text, and press the button to enter the text. Press 4) asqw to select [OK], and press the button. The text is changed. f f [MENU LOCK] Display the menu with the button, and set whether to enable menu operations. Press 1) as to select [MENU LOCK]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [OFF] Disables the lock of the menu operation. [ON] Locks the menu operation. Note After setting [MENU LOCK] to [ON], the button cannot be operated if the incorrect password is input. f f [MENU LOCK] is set to [OFF] at the time of purchase or when [INITIALIZE ALL] has been executed. f f The lock release is maintained until the projector enters standby. f f [MENU LOCK PASSWORD] Change the menu lock password. Press 1) as to select [MENU LOCK PASSWORD]. Press the button. 2) The [MENU LOCK PASSWORD] screen is displayed. f f Press 3) asqw to select the text, and press the button to enter the text. Up to 16 characters can be input. f f Press 4) asqw to select [OK], and press the button. To cancel, select [CANCEL]. f f Attention The initial password is “AAAA” at the time of purchase or when [INITIALIZE ALL] has been executed. f f Change the password periodically that is hard to guess. f f 74 - ENGLISH Chapter 4 Settings - [SECURITY] menu

Enable/disable the button operations on the control panel and the remote control. Press 1) as to select [CONTROL DEVICE SETUP]. Press the button. 2) The [CONTROL DEVICE SETUP] screen is displayed. f f Press 3) as to select one item between [CONTROL PANEL] and [REMOTE CONTROLLER]. [CONTROL PANEL] You can set the limitation on the control from the control panel. [REMOTE CONTROLLER] You can set the limitation on the control from the remote control. Press 4) qw to switch between [ENABLE] and [DISABLE]. You can set the limitation on the control from the control panel or the remote control. f f [ENABLE] Enable the button operations. [DISABLE] Disable the button operations. A confirmation screen will be displayed when you want to change [ENABLE] to [DISABLE]. f f Press 5) qw to select [OK], and then press the button. Note When a button operation is performed on the device set to [DISABLE] , the [PASSWORD] screen is displayed. f f To continue operations, enter the security password. The [PASSWORD] screen will disappear when there is no operation for approx. 10 seconds. f f If the operations of both [CONTROL PANEL] and [REMOTE CONTROLLER] are set to [DISABLE], f f the projector cannot be turned off (cannot enter standby). Even when you set button operations on the remote control to be disabled, operations of the and f f buttons on the remote control are enabled. ENGLISH - 75 Chapter 4 Settings - [SECURITY] menu

Refer to "Navigating through the menu" (Æpage 45) for the operation of the menu screen. After selecting the item, press f f asqw to set. [WIRED LAN] You can make detailed wired LAN settings. Press 1) as to select [WIRED LAN]. Press the button. 2) The [WIRED DETAILED SETUP] screen is displayed. f f Press 3) as to select an item, and change the setting according to the instructions. [DHCP] [ON]: If a DHCP server exists in the network to which the projector is connected, the IP address will automatically be acquired. [OFF]: If a DHCP server does not exist in the network to which the projector is connected, additionally set [IP ADDRESS], [SUBNET MASK] and [DEFAULT GATEWAY]. [IP ADDRESS] Enter the IP address if DHCP server is not used. [SUBNET MASK] If not using a DHCP server, enter the subnet mask. [DEFAULT GATEWAY] Enter the gateway address if DHCP server is not used. [DNS1] Enter the DNS server address if DHCP server is not used. [DNS2] Enter the alternate DNS server address if DHCP server is not used. Press 4) as to select [OK], and press button. Default wired LAN settings r r The following settings are set before the projector leaves the factory. f f [DHCP] OFF [IP ADDRESS] 192.168.10.100 [SUBNET MASK] 255.255.255.0 [DEFAULT GATEWAY] 192.168.10.1 [DNS1]/[DNS2] NULL Note When using a DHCP server, confirm that the DHCP server is running. f f Consult your network administrator regarding the IP ADDRESS, SUBNET MASK, and DEFAULT GATWAY. f f 76 - ENGLISH Chapter 4 Settings - [NETWORK] menu

Press 1) as to select [NAME CHANGE]. Press the button. 2) The [NAME CHANGE] screen is displayed. f f Select characters with the 3) asqw buttons and press the button to enter the projector name. Select [ALL DELETE] to delete all the entered characters, or press the button on the remote control to f f delete a character on the cursor in the entry field. Select [OK] with the 4) as buttons and press the button. To cancel the change of the name, select [CANCEL] and press the button. f f Note [Name f f ]( is 4-digit number) is set before the projector leaves the factory. [NETWORK CONTROL] Set when you want to control the projector from a computer connected to the network. Press 1) as to select [NETWORK CONTROL]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [ON] This function is enabled. Web control, PJLink control, the command control of the LAN are enabled. [OFF] This function is disabled. [AMX D. D.] Set to [ON] to control with the controller of AMX Corporation. Setting this function to [ON] enables detection through “AMX Device Discovery”. For details, refer to the website of AMX Corporation. URL http://www.amx.com/ Press 1) as to select [AMX D. D.] Press 2) qw to switch the item. The items will switch each time you press the button. f f [ON] This function is enabled. [OFF] This function is disabled. [Crestron Connected(TM)] Set to [ON] to control with Crestron ConnectedTM of Crestron Electronics, Inc. Press 1) as to select [Crestron Connected(TM)]. Press 2) qw to switch the item. The items will switch each time you press the button. f f [ON] This function is enabled. [OFF] This function is disabled. ENGLISH - 77 Chapter 4 Settings - [NETWORK] menu

Press 1) as to select [STATUS]. Press the button. 2) T f f he [STATUS] screen is displayed. [INITIALIZE] This function is used to return various setting values of [NETWORK] to the factory default value. Press 1) as to select [INITIALIZE]. Press the button. 2) The [INITIALIZE] screen is displayed. f f Press 3) qw to select [OK], and press the button. 78 - ENGLISH Chapter 4 Settings - [NETWORK] menu

control. Setting and adjustment of the projector. f f Display of the projector status. f f Transmission of an E-mail message when there is a problem with the projector. f f The projector supports "Crestron Connected™", and the following application software of Crestron Electronics, Inc. can be used. RoomView Express f f Fusion RV f f RoomView Server Edition f f Attention When a LAN cable is directly connected to the projector, the network connection must be made indoors. f f Note "Crestron Connected f f TM" is a system developed by Crestron Electronics, Inc. which collectively manage and control multiple system devices connected via the network, from a computer. This projector supports "Crestron ConnectedTM". For details of "Crestron Connected f f TM", refer to the Crestron Electronics, Inc. website. (Provided only in English.). http://www.crestron.com/ For the download of "RoomView Express", refer to the Crestron Electronics, Inc. website. (Provided only in English.). http://www.crestron.com/getroomview A LAN cable is required to use the network function. f f Example of a normal network connection r r A Web browser is required to use this function. Confirm that the Web browser can be used beforehand. f f Compatible OS : Windows XP/Windows Vista/Windows 7/Windows 8, Mac OS X v10.4/v10.5/v10.6/v10.7/v10.8 Compatible Web Browser : Internet Explorer 7.0/8.0/9.0/10.0, Safari 4.0/5.0/6.0 (Mac OS) Communication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be used f f beforehand. Use shielded LAN cable (STP cable) that is compatible with category 5 or above. f f Use a LAN cable with length of 100m or shorter. f f Computer Projector LAN cable (straight) LAN cable (straight) Hub ENGLISH - 79 Chapter 4 Settings - [NETWORK] menu

Activate the Web browser in the personal computer. 1) Enter the IP address set by the projector into the URL input field of the Web browser. 2) Enter your 3) “User name” and “Password”. The factory default setting of the user name is user1 (user rights)/admin1 (administrator rights) and the password is f f panasonic (lower case). Click [OK] to display the Projector status page. 4) The [Projector status] page is displayed. f f Note If you use a web browser to control the projector, set [NETWORK CONTROL] to [ON] in [NETWORK] ( f f Æpage 77). Do not perform setting or control simultaneously by starting up multiple web browsers. Do not set or control the projector f f from multiple computers. Change the password first. ( f f Æpage 89). The administrator rights allow use of all functions. The user rights allow use of [Projector status] ( f f Æ page 81), confirmation of the error information page (Æ page 82), [Network status] (Æ page 82), [Basic control] (Æ page 83), [Advanced control] (Æ page 83),and [Change password] (Æ page 89) only. Access will be locked for few minutes when an incorrect password is entered three times consecutively. f f Some items on the projector setting page use the Javascript function of the web browser. The projector may not be able to f f be controlled properly if it is set with a browser that does not have this function enabled. If the screen for the web control is not displayed, consult your network administrator. f f While updating the screen for the web control, the screen may become white for a moment, but it is not a malfunction. f f 80 - ENGLISH Chapter 4 Settings - [NETWORK] menu

1 2 3 4 5 6 Page tab 1 Switches pages by clicking this item. [Status] 2 The status of the projector is displayed by clicking this item. [Projector control] 3 The [Projector control] page is displayed by clicking this item. [Detailed set up] 4 The [Detailed set up] page is displayed by clicking this item. [Change password] 5 The [Change password] page is displayed by clicking this item. [Crestron Connected(TM)] 6 The control page of Crestron Connected™ is displayed by clicking this item. [Projector status] page Click [Status] → [Projector status]. Display the status of the projector for the following items. 13 14 15 5 6 7 8 1 2 3 4 9 10 11 12 [PROJECTOR TYPE] 1 Displays the type of projector. [MAIN VERSION] 2 Displays the firmware version of the projector. [POWER] 3 Displays the status of the power. [PICTURE MODE] 4 Displays the video mode status. [SERIAL NUMBER] 5 Displays the serial number of the projector. [NETWORK VERSION] 6 Displays the version of firmware of the network. [AV MUTE] 7 Displays the AV mute status. [VOLUME] 8 Displays the volume status. [INPUT] 9 Displays the status of the selected input. [INTAKE AIR TEMPERATURE] 10 Displays the status of the air intake temperature of the projector. [EXHAUST AIR TEMPERATURE] 11 Displays the status of the temperature around the exhaust air of the projector. [OPTIC MODULE TEMPERATURE] 12 Displays the optics module temperature status of the projector. [LAMP RUNTIME] 13 Displays the runtime of the lamps (converted value). [SELF TEST] 14 Displays the self diagnostics information. [PROJECTOR RUNTIME] 15 Displays the runtime of the projector. ENGLISH - 81 Chapter 4 Settings - [NETWORK] menu

When [Error (Detail)] or [Warning (Detail)] is displayed in the self-diagnosis display of the [Projector status] screen, click it to display the error/warning details. The projector may go into the standby status to protect the projector depending on the contents of the error. f f 1 Self-diagnosis result display 1 Displays the item check results. [OK]: Indicates that operation is normal. [FAILED]: Indicates that there is a problem. [WARNING]: Indicates that there is a warning. [FAILED] items displayed when a problem occurs r r Parameter Description [FAN] Trouble has occurred in the fan or its drive circuit. Consult your dealer. [FAN(INTAKE)] Trouble has occurred in the intake fan. [FAN(EXHAUST)] Trouble has occurred in the exhaust fan. [FAN(LAMP)] Trouble has occurred in the lamp cooling fan. [INTAKE AIR TEMPERATURE] The air intake temperature is too high. The projector may be used in an operating environment where the temperature is high, such as near a heating appliance. [EXHAUST AIR TEMPERATURE] The exhaust air temperature is high. The air exhaust port may be blocked. [OPTICS MODULE TEMPERATURE] The temperature around the optics module inside the projector is high. The projector may be used in an operating environment where the temperature is high, such as near a heating appliance. [LAMP REMAIN TIME] The lamp runtime has exceeded the prescribed cumulative time, and it is now time to replace the lamp. [LAMP STATUS] The lamp has failed to light. Wait a short while for the lamp to cool off, and then turn on the power. [APERTURE (CONTRAST-SHUTTER)] Trouble has occurred in the contrast shutter circuitry. Consult your dealer. [AIR FILTER] There is too much dust accumulated in the air filter unit. Turning off the projector and clean the air filter unit. [Network status] page Click [Status] → [Network status]. The current network setting status is displayed. 82 - ENGLISH Chapter 4 Settings - [NETWORK] menu

Click [Projector control] → [Basic control]. 1 2 5 6 3 4 [INPUT] 1 Switches the input signal. [VOLUME] 2 Adjusts the volume level. [PICTURE MODE] 3 Switches the picture mode. [AV MUTE] 4 Switches between AV mute on/off. [POWER] 5 Turns on/off the power. [CLOSED CAPTION] 6 Switches the closed caption mode. [Advanced control] page Click [Projector control] → [Advanced control]. 1 2 [POSITION] 1 Adjusts the position of image and the keystone correction. [PICTURE] 2 Adjusts the items of image. ENGLISH - 83 Chapter 4 Settings - [NETWORK] menu

Click [Detailed set up] → [Network config]. Click [Network config] to display the [CAUTION!] screen. f f The current settings are displayed by pressing the [Next] button. f f Click [Change] to display the setting change screen. f f 2 7 1 3 4 5 6 [Projector name] 1 Enter the name of the projector. Enter the host name if it is required when using a DHCP server etc. [DHCP ON]/[DHCP OFF] 2 To enable the DHCP client function, set to [DHCP ON]. [IP ADDRESS] 3 Enter the IP address when not using a DHCP server. [SUBNET MASK] 4 Enter the subnet mask when not using a DHCP server. [DEFAULT GATEWAY] 5 Enter the default gateway address when not using a DHCP server. [DNS1]/[DNS2] 6 Enter the DNS1/DNS2 server address. Permissible/ available characters for the entry of DNS1/ DNS2 server address. (primary): Numbers (0 - 9), period (.) (Example: 192.168.0.253). [Back]/[Next] 7 Click the [Back] button to return to the original screen. The current settings are displayed by pressing the [Next] button. Click the [Submit] button to update the settings. Note When you use the “Forward” and “Back” functions of your browser, a warning message “Page has Expired” may appear. In f f that case, click [Network config] again since the following operation will not be guaranteed. Changing LAN settings while connected to the LAN may cause the connection to cut out. f f 84 - ENGLISH Chapter 4 Settings - [NETWORK] menu

Check whether the network is connected to the mail server, POP server, DNS server, etc. Click [Detailed set up] → [Ping test]. 3 4 1 2 [ Input IP address] 1 Enter the IP address of the server to be tested. [Submit] 2 Executes the connection test. Example of display when the connection has 3 succeeded Example of display when the connection has failed 4 [E-mail set up] page When there is a problem or the runtime of a lamp reaches a set value, an E-mail can be sent to preset E-mail addresses (up to two addresses). Click [Detailed set up] → [E-mail set up]. 1 2 3 4 5 6 [ENABLE] 1 Select [Enable] to use the E-mail function. [SMTP SERVER NAME] 2 Enter the IP address or the server name of the E-mail server (SMTP). To enter the server name, the DNS server needs to beset up. [MAIL FROM] 3 Enter the E-mail address of the projector. (Up to 63 characters in single byte) [MEMO] 4 Enter information such as the location of the projector that notifies the sender of the E-mail. (Up to 63 characters in single byte) [MINIMUM TIME] 5 Change the minimum interval for the temperature warning E-mail. The default value is 60 minutes. In this case, another E-mail will not be sent for 60 minutes after sending the temperature warning E-mail even if it reaches the warning temperature. [INTAKE AIR TEMPERATURE] 6 Change the temperature setting for the temperature warning mail. A temperature warning E-mail is sent when the temperature exceeds this value. ENGLISH - 85 Chapter 4 Settings - [NETWORK] menu

7 Enter the E-mail address to be sent. Leave [E-MAIL ADDRESS 2] blank when two E-mail addresses are not to be used. Settings of the conditions to send E-mail 8 Select the conditions to send E-mail. [MAIL CONTENTS]: Select either [NORMAL] or [SIMPLE]. [ERROR]: Send an E-mail when an error occurred in the self- diagnosis. [LAMP RUNTIME]: An E-mail message is sent when the remaining lamp on time for the lamp has reached the value set at the right field. [INTAKE AIR TEMPERATURE]: Send an E-mail when the air intake temperature has reached the value set at the above field. [Submit] 9 Update the settings. [Authentication set up] page Set the authentication items when POP authentication or SMTP authentication is necessary to send an E-mail. Click [Detailed set up] → [Authentication set up]. 1 2 3 4 5 6 7 8 [Auth] 1 Select the authentication method specified by your Internet service provider. [SMTP Auth] 2 Set when the SMTP authentication is selected. [POP server name] 3 Enter the POP server name. Allowed characters: Alphanumerics (A - Z, a - z, 0 - 9) Minus sign (-) and period (.) [User name] 4 Enter the user name for the POP server or the SMTP server. [Password] 5 Enter the password for the POP server or the SMTP server. [SMTP server port] 6 Enter the port number of the SMTP server. (Normally 25) [POP server port] 7 Enter the port number of the POP server. (Normally 110) [Submit] 8 Update the settings. 86 - ENGLISH Chapter 4 Settings - [NETWORK] menu

Example of E-mail sent when E-mail is set Mail with the contents shown below is sent when the e-mail settings have been established. === Panasonic projector report(CONFIGURE) === Projector Type : PT-VX42Z Serial No : 000000000 ----- E-mail setup data ----- TEMPERATURE WARNING SETUP MINIMUM TIME at [ 60] minutes interval INTAKE AIR TEMPERATURE Over [ 32degC / 89degF ] ERROR [ OFF ] LAMP RUNTIME [ OFF ] at REMAIN [ 400] H LAMP RUNTIME [ OFF ] at REMAIN [ 200] H INTAKE AIR TEMPERATURE [ OFF ] ----- check system ----- FAN [ OK ] FAN(INTAKE) [ OK ] FAN(EXHAUST) [ OK ] FAN(LAMP) [ OK ] INTAKE AIR TEMPERATURE [ OK ] EXHAUST AIR TEMPERATURE [ OK ] OPTICS MODULE TEMPERATURE [ OK ] LAMP REMAIN TIME [ OK ] LAMP STATUS [ OK ] APERTURE (CONTRAST-SHUTTER) [ OK ] AIR FILTER [ OK ] (Error code 00 00 00 00 00 00 00 00) Intake air temperature : 31 degC / 87 degF Exhaust air temperature : 37 degC / 98 degF Optics module temperature : 39 degC / 102 degF PROJECTOR RUNTIME 800 H LAMP NORMAL 100 H LAMP ECO1 500 H LAMP ECO2 200 H LAMP REMAIN 3400 H -------- Current status --------- MAIN VERSION 1.00 NETWORK VERSION 1.00 SUB VERSION 1.00 LAMP STATUS LAMP=ON INPUT RGB SIGNAL NAME XGA6 SIGNAL FREQUENCY 0.00kHz / 0.00Hz ----- Wired Network configuration ----- DHCP Client OFF IP address 192.168.10.100 MAC address 04:20:9A:00:00:00 ----- Memo ----- ENGLISH - 87 Chapter 4 Settings - [NETWORK] menu

Mail with the contents shown below is sent when an error has occurred. === Panasonic projector report(ERROR) === Projector Type : PT-VX42Z Serial No : 000000000 ----- check system ----- FAN [ OK ] FAN(INTAKE) [ OK ] FAN(EXHAUST) [ OK ] FAN(LAMP) [ OK ] INTAKE AIR TEMPERATURE [ OK ] EXHAUST AIR TEMPERATURE [ OK ] OPTICS MODULE TEMPERATURE [ OK ] LAMP REMAIN TIME [ OK ] LAMP STATUS [ OK ] APERTURE (CONTRAST-SHUTTER) [ OK ] AIR FILTER [ FAILED ] (Error code 00 40 00 00 00 00 00 08) Intake air temperature : 31 degC / 87 degF Exhaust air temperature : 37 degC / 98 degF Optics module temperature : 39 degC / 102 degF PROJECTOR RUNTIME 800 H LAMP NORMAL 100 H LAMP ECO1 500 H LAMP ECO2 200 H LAMP REMAIN 3400 H -------- Current status --------- MAIN VERSION 1.00 NETWORK VERSION 1.00 SUB VERSION 1.00 LAMP STATUS LAMP=OFF INPUT NETWORK ----- Wired Network configuration ----- DHCP Client OFF IP address 192.168.10.100 MAC address 04:20:9A:00:00:00 ----- Memo ----- [Port set up] page Set the port number used for command control. Click [Detailed set up] → [Port set up]. 1 2 3 [COMMAND PORT] 1 Set the port number used for command control. [Wake on LAN PORT] 2 When [STANDBY MODE] is set to [NETWORK], set the port number used for the Wake on LAN function. [Submit] 3 Update the settings. 88 - ENGLISH Chapter 4 Settings - [NETWORK] menu

You can make settings for the ECO management function of the projector. Click [Detailed set up] → [ECO management set up]. 1 2 3 4 5 6 7 8 [LAMP POWER] 1 Selects the [LAMP POWER] setting. [AUTO POWER SAVE] 2 Select [ON] to set [AMBIENT LIGHT DETECTION], [SIGNAL DETECTION], and [AV MUTE DETECTION]. [AMBIENT LIGHT DETECTION] 3 Enable ([ON])/disable ([OFF]) the ambient light detection function. [SIGNAL DETECTION] 4 Enable ([ON])/disable ([OFF]) the signal detection function. [AV MUTE DETECTION] 5 Enable ([ON])/disable ([OFF]) the AV mute detection function. [POWER MANAGEMENT] 6 Select the power consumption mode. [TIMER] 7 Select the time that the lamp is turned off when the POWER MANAGEMENT function is using. [Submit] 8 Update the setting. Note For detailed description of each setting item, refer to the [PROJECTOR SETUP] menu of the projector → [ECO f f MANAGEMENT] (Æpage 68). [Change Password] page Click [Change password]. 1 2 3 [Administrator] 1 Used to change the setting of [Administrator]. [User] 2 Used to change the setting of [User]. [Next] 3 Used to change the setting of the password. ENGLISH - 89 Chapter 4 Settings - [NETWORK] menu

1 Displays the account to change. [Current] [User name] 2 Enter the user name before the change. [Current] [Password] 3 Enter the current password. [New] [User name] 4 Enter the desired new user name. (Up to 16 characters in single byte) [New] [Password] 5 Enter the desired new password. (Up to 16 characters in single byte) [New] [Password (Retype)] 6 Enter the desired new password again. [OK] 7 Determines the change of password. [User] account 1 2 3 5 4 [Account : User] 1 Displays the account to change. [New] [User name] 2 Enter the desired new user name. (Up to 16 characters in single byte) [New] [Password] 3 Enter the desired new password. (Up to 16 characters in single byte) [New] [Password (Retype)] 4 Enter the desired new password again. [OK] 5 Determines the change of password. [Change Password] (For user rights) Only the change of password is enabled under the user rights. 1 2 4 3 90 - ENGLISH Chapter 4 Settings - [NETWORK] menu

[New password] 2 Enter the desired new password. (Up to 16 characters in single byte) [Retype] 3 Enter the desired new password again. [OK] 4 Determines the change of password. Note To change the account of the administrator, you must enter the [User name] and [Password] in [Current]. f f [Crestron Conneted(TM)] page The projector can be monitored/controlled with Crestron ConnectedTM. To start the Crestron ConnetedTM control page from the web control screen, you need to access with the administrator rights. (For user rights, the [Crestron Conneted(TM)] button is not displayed on the web control screen.) The control page of Crestron ConnetedTM is displayed by clicking [Crestron Conneted(TM)]. It is not displayed if Adobe Flash Player is not installed on the computer used, or the browser used does not support Flash. In that case, click [Back] on the control page to go back to the previous page. Control page 1 2 3 4 5 6 7 [Tools][Info][Help] 1 Tabs for selecting the setting, information, or help page of the projector. [POWER] 2 Turns on/off the power. [VOL DOWN]/[AU MUTE]/[VOL UP] 3 Adjusts the volume. Switches the AV mute function on/off. [Input Select] 4 Controls input select. Not available when the power of the projector is turned off. Menu screen control buttons 5 Navigates the menu screen. Freeze/image quality adjustment 6 Controls items related to freeze/image quality. [Back] 7 Performs return to the previous page. [Tools] page Click [Tools] on the control page. 1 2 3 4 5 ENGLISH - 91 Chapter 4 Settings - [NETWORK] menu

controller to be connected with the projector. [User Password] 2 Set the user rights password for the Crestron ConnectedTM control page. [Admin Password] 3 Set the administrator rights password for the Crestron ConnectedTM control page. Network status 4 Displays the settings of wired LAN. [DHCP] Displays the current setting. [Ip Address] Displays the current setting. [Subnet Mask] Displays the current setting. [Default Gateway] Displays the current setting. [DNS Server] Displays the current setting. [Exit] 5 Returns to the control page. [Info] page Click [Info] on the control page. 4 5 6 7 1 2 3 8 [Projector Name] 1 Displays the projector name. [Mac Address] 2 Displays the MAC address. [Lamp Hours] 3 Displays the runtime of the lamps (converted value). [Power Status] 4 Displays the status of the power. [Source] 5 Displays the selected input. [Lamp Mode] 6 Displays [LAMP POWER] (Æ page 68). [Error Status] 7 Displays the error status. [Exit] 8 Returns to the control page. [Help] page Click [Help] on the control page. The [Help Desk] window is displayed. 1 [Help Desk] 1 Send/receive messages to/from an administrator who uses Crestron ConnectedTM. 92 - ENGLISH Chapter 4 Settings - [NETWORK] menu

This chapter describes methods of inspection when there are problems, maintenance, and replacements of the units. ENGLISH - 93

Managing the indicated problems If a problem should occur inside the projector, the , and/or indicators will inform you. Manage the indicated problems as follow. Attention Before you take a remedial measure, follow the procedure of switching the power off indicated in “Powering Off the f f projector”. (Æpage 38) LAMP indicator Indicator Lighting in red. Flashing in red. Status Time to replace the lamp unit. A problem is detected in the lamp or the power supply for the lamp. Check Was [REPLACE LAMP] displayed when f f you turned on the power? The indicator lights up when the f f runtime of the lamp unit has reached 4 000 hours (when [LAMP POWER] is set to [NORMAL]). Have you turned on the f f power again immediately after turning it off? Some error has occurred in f f the lamp circuit. Check for fluctuation (or drop) in the source voltage. Remedy Replace the lamp unit. f f Wait a while until the f f luminous lamp cools off, and then turn on the power. Turn off the projector, and f f unplug the AC power cord, and consult your dealer. Note Contact your dealer for repair services when indicator persists to light after taking these measurements. f f WARNING indicator Indicator Lighting in red. Flashing in red. Flashing in red. (Slow) Status Internal temperature is high (warning). Internal temperature is high (standby status). The projector detects an abnormal condition and cannot be turned on. Check Is the air intake/exhaust port blocked? f f Is the room temperature high? f f Is the air filter unit clogged? f f _ Remedy Remove any objects that are blocking the air intake/ exhaust port. f f Install the projector in a location with an ambient temperature of 0 °C f f (32 °F) to 40 °C (104 °F) Do not use the projector at high altitudes of 2 700 m (8 858') or higher f f above sea level. Replace the air filter unit. ( f f Æpage 95) If the projector is turned off f f again, unplug the AC power cord and contact the dealer or the service center for service and checkup. Note If indicator persists to light or blink after taking these measurements, please contact your dealer for repair f f services. Do not leave the projector on. It may cause an electric shock or a fire hazard. The projector detects an abnormal condition and cannot be turned on. Unplug the AC power cord and plug it again to turn on f f the projector. If the projector is turned off again, unplug the AC power cord and contact the dealer or the service center for service and checkup. Do not leave the projector on. It may cause an electric shock or a fire hazard. indicator indicator 94 - ENGLISH Chapter 5 Maintenance - LAMP and WARNING Indicators

When you perform maintenance or replacement of the parts, make sure to turn off the power and disconnect the power plug f f from the wall outlet. (Æ pages 35, 38) Be sure to observe the procedure “Powering Off the projector” ( f f Æ page 38) when performing power supply operation. Maintenance Outer Case Wipe off dirt and dust using a soft dry cloth. If the dirt is persistent, soak the cloth with water and wring it thoroughly before wiping. Dry off the projector with a dry cloth. f f Do not use benzene, thinner, or rubbing alcohol, other solvents, household cleaners. Using them may cause deterioration of f f the outer case. When using chemical treated dusters, follow its instruction. f f Front glass surface of the lens Wipe off the dirt and dust off the front surface of the lens with soft clean cloth. Do not use a cloth that has an abrasive surface or a cloth that is moist, oily, or covered with dust. f f Do not use excessive force when wiping the lens as it is fragile. f f Attention The lens is made of glass. Impacts or excessive force when wiping may scratch its surface. f f Please handle with care. Replacing the unit Air filter unit The air filter prevents dust from accumulating on the optical elements inside the projector. Should the air filter become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life of the projector. If the air filter unit become clogged, it will result in internal heat buildup, the power of the projector may be turned off for safety. If a warning message appears on the screen, replace the air filter immediately. Consult your dealer to purchase a replacement air filter unit (ET-RFV300). Removing the air filter unit Remove the air filter cover. (Fig.1) 1) Open the air filter cover in the direction of the arrow and remove it. f f Remove the air filter unit. 2) Hold the tab of the air filter unit and pull out in the direction of the arrow. (Fig.2) f f After removing the air filter unit, remove foreign objects and dust from the air filter compartment and the projector’s air f f intake port if there are any. Fig.1 Fig.2 Air filter cover Air filter unit Tab ENGLISH - 95 Chapter 5 Maintenance - Replacement

Attach the unused air filter unit to the projector. 1) Hold the air filter unit that the tab is in up-left side in the figure, put the right side in the figure first, and press the tab side f f until make a click sound. Do not press any other part of the air filter unit except the frame during installation. f f Install the air filter cover. 2) Perform Step 1) in “Removing the air filter unit” ( f f Æ page 95) in the reverse order . Make sure that the air filter cover is closed tightly. f f Resetting the filter counter. Be sure to reset the filter counter after replacing the air filter unit. Connect the power plug, press the < 1) v/b> button on the control panel or on the remote control. Press the button to display the main menu, then press 2) as to select [PROJECTOR SETUP]. Press the button, press 3) as to select [FILTER COUNTER]. Press the button, press 4) as to select [FILTER COUNTER RESET]. Press the button. 5) [FILTER COUNTER RESET] confirmation is displayed. f f Press 6) qw to select [OK], then press the button. The filter usage time is 0 after reset. f f Attention Turn off the power before you replace the air filter unit. f f When attaching the air filter unit, make sure that the projector is stable, and work in an environment that is safe, even in the f f event of the air filter unit dropping. Make sure that the air filter unit is properly attached before using the projector. If it is not attached, the projector will suck in f f dirt and dust causing a malfunction. Do not put anything into the air vents. Doing so may result in malfunction of the projector. f f The air filter unit to be replaced should be an unused product. f f After replacing the air filter, reset the filter counter. Otherwise, “FILTER COUNTER has reached the set time.” will appear on f f screen. Note The replacement cycle of the air filter unit varies greatly depending on the usage environment. f f Lamp unit The lamp unit is a consumable component. Refer to “When to replace the lamp unit” (Æ page 97) for details about the replacement cycle. It is recommended to ask an authorized engineer to replace the lamp unit. Contact your dealer. Consult your dealer to purchase a replacement lamp unit (ET-LAV300). Warning Do not replace the lamp unit when it is hot. (Wait at least 1 hour after use.) The inside of the cover can become very hot, take care to avoid burn injuries. Tab 96 - ENGLISH Chapter 5 Maintenance - Replacement

The luminous source of the lamp is made of glass and may burst if you hit it against a hard surface or drop it. Please handle f f with care. A Phillips screwdriver is required for replacement of the lamp unit. f f When replacing the lamp unit, be sure to hold it by the handle. f f When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. If replacing f f the lamp of a projector which has been installed on the ceiling, you should always assume that the lamp is broken, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened. If pieces of glass get into your eyes or mouth, seek medical advice immediately. The lamp may be ruptured. Care should be taken not to scatter pieces of the broken lamp glass when replacing the lamp f f unit. Pieces of the broken lamp may fall from the lamp unit especially when the projector is mounted on the ceiling, so when replacing the lamp unit do not stand directly underneath it or position your face close to it. The lamp contains mercury. Consult your local municipality or your dealer about correct disposal of used lamp units. f f Attention Panasonic takes no responsibility for any damage or malfunction of the product resulting from use of lamp units which are f f not manufactured by Panasonic. Use only specified lamp units. Note The model numbers of accessories and optional accessories are subject to change without prior notice. f f When to replace the lamp unit The lamp unit is a consumable component. Since its brightness gradually decreases over time, it is necessary to replace the lamp unit regularly. The estimated duration before replacement is 4 000 hours, but the lamp may go off before 4 000 hours has elapsed depending on individual lamp characteristics, usage conditions, and the installation environment. It is recommended that the Replacement lamp unit be prepared earlier. If you continue to use the lamp unit after 4 000 hours has elapsed, the lamp turns off automatically after approximately 10 minutes, as it will cause malfunction of the projector. Lamp runtime On-screen display REPLACE LAMP LAMP indicator Over 3 800 hours The message is displayed for 30 seconds. If you press any button within the 30 seconds, the message disap- pears. Lights in red (even in stand-by mode). Over 4 000 hours If the power is turned on without replacing the lamp, the power automatically turns off after approximately ten min- utes to prevent the malfunction of the projector. Note To predict when to replace the lamp, check the lamp runtime displayed in [RUNTIME] in [STATUS] ( f f Æ page 66). 4 000 hours of use is a rough guideline, but is not a guarantee. The lamp runtime differs depending on the setting of "LAMP f f POWER" menu. Replacing the Lamp unit Attention When the projector is mounted on a ceiling, do not work with your face close to the projector. f f Attach the lamp unit and the lamp cover securely. f f When you experience difficulty in installing the lamp, remove it and try again. If you use force to install the lamp, the f f connector may be damaged. Do not loosen other than designated screws. f f Lamp cover Lamp unit fixing screws Handles Lamp cover fixing screw ENGLISH - 97 Chapter 5 Maintenance - Replacement

When moving this projector or while not using it over an extended period of time, attach the lens cap. To prevent loss for the lens cap, please according to the following procedures, attach the lens cap with the string of accessories. Thread the thinner end of the string through the hole on the lens cap. 1) Lens cap String Thread the other end of the string through the hole on the bottom of the projector. 2) Turn off the Power by following the procedure in "Powering Off the Projector" ( 1) Æ page 38). Remove the AC power plug from the wall outlet. Wait at least 1 hour and make sure the lamp unit and surroundings are cool. Remove the lamp cover. 2) Use a Phillips screwdriver to loosen the lamp cover fixing screw (×1) and remove the lamp cover. Remove the lamp cover by pulling it slowly toward the direction of the arrow. f f Remove the lamp unit. 3) Use a Phillips screwdriver to loosen the three lamp unit fixing screws (×3) until the screws turn freely. Hold the used lamp unit by its handles, and pull it gently from the projector. Attach the unused lamp unit. 4) Insert the new lamp unit in correct direction. Tighten the three lamp unit fixing screws (×3) securely with a Phillips screwdriver. Attach the lamp cover. 5) Attach the lamp cover, and tighten the lamp cover fixing screw (×1) securely with a Phillips screwdriver. Attach the lamp cover by pushing it slowly opposite the direction of the arrow. f f Note When you replace the lamp unit with new one, the projector resets the runtime of the lamp unit automatically. f f 98 - ENGLISH Chapter 5 Maintenance - Replacement

Problem Cause Reference page Power does not turn on. The power cord may not be connected. f f No electric supply is at the wall outlet. f f The circuit breakers have tripped. f f Is the indicator or indicator lit or blinking? f f The lamp cover has not been securely installed. f f — — — 36, 94 97 No picture appears. The video signal input source may not be connected to a terminal properly. f f The input selection setting may not be correct. f f The [BRIGHTNESS] adjustment setting may be at the minimum setting. f f The input source which is connected to the projector may have a problem. f f The AV MUTE function may be in use. f f 32 41 50 — 42 The picture is fuzzy. The lens cap is still attached to the lens. f f The lens focus may not have been set correctly. f f The projector may not be at the correct distance from the screen. f f The lens may be dirty. f f The projector may be tilted too much. f f 17 39 27-28 17 — The color is pale or grayish. [COLOR] or [TINT] adjustment may be incorrect. f f The input source which is connected to the projector may not be adjusted f f correctly. RGB cable is damaged. f f 50 — — No sound from the internal speaker. The input terminals may not have been correctly connected. f f The volume may have been set to the minimum level. f f The AV MUTE function may have been turned on. f f When the VARIABLE AUDIO OUT is plugged-in, the projector's built-in speaker f f is not available. The MUTE function may have been turned on. f f 30-33 43, 70 42 23 43, 70 The remote control does not operate. The batteries may be weak. f f The batteries may not have been inserted correctly. f f The remote control signal receptor on the projector may be obstructed. f f The remote control unit may be out of the operation range. f f Strong light such as fluorescent shine onto the signal receptor. f f When different codes are set on the projector and on the remote control. f f The [REMOTE CONTROL] setting is set to [DISABLE] in [CONTROL DEVICE f f SETUP]. — 24 21 21 21 67 75 The control buttons of the projector do not operate. The [CONTROL PANEL] setting is set to [DISABLE] in [CONTROL DEVICE f f SETUP]. 75 The picture does not display correctly. There may be a problem with the VCR or other signal source. f f A signal which is not compatible with the projector is being input. f f — 107-108 Picture from a computer does not appear. The cable may be longer than the optional cable. f f The external video output from a laptop computer may not be correct. f f — — Picture from a HDMI device does not appear or picture is not stable. Is the HDMI cable securely connected? f f Turn off the power of the projector and the connected devices. Then turn the f f power of the projector and the connected devices back on. Isn't unsupported signal cable connected? f f 32 — 107-108 No sound is output from a HDMI device. Set the sound channel of the attached device to Linear PCM. f f — Attention If the problem persists, after confirming the contents of the table, please consult your dealer. f f ENGLISH - 99 Chapter 5 Maintenance - Troubleshooting

This chapter describes specifications and after-sales service for the projector. 100 - ENGLISH