Panasonic PV-C2022 Operating Instructions Manual

operate, or adjust this product. Please save this manual. Spanish Quick Use Guide is included. (Guía para rápida consulta en español está incluida.) Combination VCR Operating Instructions Model No. PV-C2022/PV-C2032W LSQT0517A Basic Operation Initial Setup TV Operation Timer Operation Advanced Operation For Your Information • Initial Setup and Connection Procedures are on pages 8 and 9. As an ENERGY STAR® Partner, Matsushita Electric Corporation of America has determined that this product or product model meets the ENERGY STAR® guidelines for energy efficiency. LSQT0517A_01p09.p65 11/12/2001, 12:02 PM 1

INSTALLATION 1 POWER SOURCE CAUTION Operate only from power source indicated on unit or in this manual. If uncertain, have your Electric Utility Service Company or Video Products Dealer verify your home power source. 2 POWER CORD PLUG For safety, this unit has a polarized type plug (one wide blade), or a three-wire grounding type plug. Always hold the plug firmly and make sure your hands are dry when plugging in or unplugging the AC power cord. Regularly remove dust, dirt, etc. on the plug. POLARIZED PLUG CAUTION: The plug fits into outlet one way. If it cannot be fully inserted, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not tamper with the plug. GROUNDING PLUG CAUTION: The plug requires a three-hole grounding outlet. If necessary, have an electrician install the proper outlet. Do not tamper with the plug. 3 POWER CORD To avoid unit malfunction, and to protect against electrical shock, fire or personal injury: -Keep power cord away from heating appliances and walking traffic. Do not rest heavy objects on, or roll such objects over the power cord. -Do not tamper with the cord in any way. -An extension cord should have the same type plug (polarized or grounding) and must be securely connected. -Overloaded wall outlets or extension cords is a fire hazard. -Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified electrician. 4 DO NOT BLOCK VENTILATION HOLES Ventilation openings in the cabinet release heat generated during operation. If blocked, heat build-up may result in a fire hazard or heat damage to cassettes. For your protection: a. Never cover ventilation slots while unit is ON, or operate unit while placed on a bed, sofa, rug, or other soft surface. b. Avoid built-in installation, such as a book case or rack, unless properly ventilated. 5 AVOID EXTREMELY HOT LOCATIONS OR SUDDEN TEMPERATURE CHANGES Do not place unit over or near a heater or regulator, in direct sunlight, etc. If unit is suddenly moved from a cold place to a warm place, moisture may condense in unit and on the tape causing damage. 6 TO AVOID PERSONAL INJURY • Never place unit on support or stand that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit. • Move any appliance and cart combination with care. Quick stops, excessive force, and uneven surfaces may cause objects to overturn. • Carefully follow all operating instructions. USING THE UNIT Before unit is brought out of storage or moved to a new location, refer again to the INSTALLATION section of these safeguards. 1 KEEP UNIT WELL AWAY FROM WATER OR MOISTURE, such as vases, sinks, tubs, etc. 2 IF EXPOSED TO RAIN, MOISTURE, OR STRONG IMPACT, unplug unit and have it inspected by a qualified service technician before use. 3 ELECTRICAL STORMS During a lightning storm, or before leaving unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system. 4 WHEN UNIT IS PLUGGED IN • DO NOT OPERATE IF: - liquid has spilled into unit. - unit was dropped or otherwise damaged. - unit emits smoke, malodors, or noises. Immediately unplug unit, and have it inspected by a service technician to avoid potential fire and shock hazards. • Never drop or push any object through openings in unit. Touching internal parts may cause electric shock or fire hazard. • Keep magnetic objects, such as speakers, away from unit to avoid electrical interference. 5 USING ACCESSORIES Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards. 6 CLEANING UNIT Unplug unit. Use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into unit and cause electrical shock. Any substance, such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts. READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON UNIT SERVICE 1 DO NOT SERVICE PRODUCT YOURSELF If, after carefully following detailed operating instructions, the unit does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug unit and contact a qualified service technician. 2 REPLACEMENT OF PARTS Make sure the service technician uses only parts specified by the manufacturer, or have equal safety characteristics as original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards. 3 SAFETY CHECK AFTER SERVICING After unit is serviced or repaired, request that a through safety check be done as described in the manufacturer’s service literature to insure video unit is in safe operating condition. OUTDOOR ANTENNA INSTALLATION 1 SAFE ANTENNA AND CABLE CONNECTION An outside antenna or cable system must be properly grounded to provide some protection against built up static charges and voltage. Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical Code) provides information regarding proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS Locate an outside antenna system well away from power lines and electric light or power circuits so it will never touch these power sources should it ever fall. When installing antenna, absolutely never touch power lines, circuits or other power sources as this could be fatal. GROUND CLAMP ELECTRIC SERVICE EQUIPMENT ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) NEC - NATIONAL ELECTRICAL CODE For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] LSQT0517A_01p09.p65 11/12/2001, 12:02 PM 2

Warning : To prevent fire or shock hazard, do not expose this equipment to rain or moisture. Caution : To prevent electric shock, match wide blade of plug to wide slot, fully insert. Avertissement : Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive. Attention :Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond. This video recorder, equipped with the HQ (High Quality) System, is compatible with existing VHS equipment. Only use those tapes with the mark. It is recommended that only cassette tapes that have been tested and inspected for use in 2, 4, 6, and 8 hour VCR machines be used. This television receiver provides display of television closed captioning in accordance with §15.119 of the FCC rules. FCC WARNING : Any unauthorized changes or modifications to this equipment would void the user’s authority to operate. This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION Congratulations on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you and your family years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your unit. Date of Purchase Dealer Purchased From Dealer Address Dealer Phone No. Model No. Serial No. Batteries 2 “AA” Accessories To order accessories, call toll free 1-800-332-5368. Remote Control LSSQ0278 (PV-C2022) LSSQ0279 (PV-C2032W) Loading the Batteries Battery replacement caution • Do not mix old and new batteries. • Do not mix alkaline with manganese batteries. Prevent Accidental Tape Erasure Break off the tab to prevent recording. Record Tab Screwdriver To record again. Cover the hole with cellophane tape. This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: [email protected] LSQT0517A_01p09.p65 11/12/2001, 12:02 PM 3

deflection Picture Tube VCR Video Recording 2 rotary heads helical System: scanning system Audio Track: 1 track Tuner Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69 CABLE Channels: Midband A through I (14 ~ 22) Superband J through W (23 ~ 36) Hyperband AA ~ EEE (37 ~ 64) Lowband A-5 ~ A-1 (95 ~ 99) Special CABLE channel 5A(01) Ultraband 65 ~ 94, 100 ~ 125 FM Radio Band Range: 87.5 ~ 108.1 MHz General Power Source: 120 V AC, 60 Hz Power Consumption: Power On Approx. 110 watts Power Off Approx. 2.5 watts Television System: EIA Standard NTSC color Speaker: 1 piece Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F) Operating Humidity:10 % ~ 75 % Weight: 23 Kg (50.6 lbs.) Dimensions: 515 (W) X 505 (H) X 474 (D) mm 20-5/16” (W) X 19-7/8” (H) X 18-11/16” (D) Note: Designs and specifications are subject to change without notice. Head Cleaning Record/Playback Time Only use tapes with the mark in this unit. SP (Standard Play) 2 Hours 40 Minutes 1 Hour 5 Hours 20 Minutes 2 Hours LP (Long Play) 3 Hours 8 Hours SLP (Super Long Play) Type of Video Cassette Tape Speed Setting T160 T60 Unit auto adjusts clock for DST (Daylight Saving Time.) IIIII Spring (First Sunday in April) DST : ON => Sets clock ahead one hour. IIIII Autumn (Last Sunday in October) DST : ON => Turns clock back one hour. • If your area does not observe Daylight Saving Time, select DST:OFF. • Keep these time changes in mind when programming the unit for timer recordings. DST (Daylight Saving Time) 2 Hour 4 Hours 6 Hours T120 Digital Auto Tracking Continuously analyzes the signal and adjusts for optimum picture quality. Manual Tracking Control (to reduce picture noise) Use during Playback and Slow Motion mode to reduce picture noise. Press the 3 or 6 number key on the remote control or CH on the unit until the picture clears up. To return to Auto Tracking, press POWER off, then on again a few seconds later. Unit Information Features for a Quality Picture For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] V I DEO HEADS MAY NEED CLEAN I NG PL EASE I NSERT HEAD CLEAN I NG CASSETTE OR REFER TO MANUAL END : PLAY KEY Playing older or damaged tapes may eventually cause video heads to become clogged. Head Clog Sensor During playback this screen appears if clogging is detected. To remove screen, press PLAY on the remote or unit. • Use “dry” type head cleaning cassette only. (Part No. NV-TCL30PT is recommended.) • Follow cleaning tape directions carefully. Excessive use of head cleaning tape can shorten the video head life. • If head clog symptoms persist, contact your nearest Factory Service Center or authorized Service Center. (See Page 34.) LSQT0517A_01p09.p65 11/20/2001, 8:59 AM 4

Important Safeguards and Precautions / Safety Precautions .... 2,3 Before Using....................................................................................... 4 Unit Information ................................................................................. 4 Table of Contents................................................................................ 5 Location of Controls ........................................................................... 6 Connections / Initial Setup (Ready to Play) .................................. 8,9 Reset Language, Channels, Clock, Time Zone Adjust............. 10,11 Playback a Tape ................................................................................ 12 Record On a Tape ............................................................................. 12 Copy Your Tapes (Dubbing) ............................................................ 13 Tape Operation ........................................................................... 24~26 Special VCR Features................................................................. 27,28 V-Chip Control Feature.............................................................. 29~31 On-Screen Display (OSD)................................................................. 32 Before Requesting Service ...............................................................33 Servicenter List ..................................................................................34 Limited Warranty ...............................................................................35 Spanish Quick Use Guide / Guía para rápida consulta ........... 36,37 Index .................................................................................................. BC TV Operation .................................................................................... 14 Picture Adjustment .......................................................................... 15 TV Timer Features ....................................................................... 16,17 Closed Caption System .............................................................. 18,19 Timer Recording.......................................................................... 22,23 Basic Operation TV Operation Timer Operation Advanced Operation For Your Information Initial Setup FM Radio ...................................................................................... 20,21 [email protected] LSQT0517A_01p09.p65 11/20/2001, 8:59 AM 5

Remote Control Buttons • When EJECT is pressed, the tape is ejected from Cassette Compartment. If EJECT is pressed during recording, the unit will not respond to the command. EJECT Ejects tape. POWER Turn on or off the unit. FM/TV Receives FM radio signal. MUTE Mutes the sound instantly. CHANNEL UP/DOWN Selects a channel. SELECT UP/DOWN Control navigation around on-screen menu. ACTION Displays Main Menu. NUMBER Keys Selects a channel directly. REWIND/SEARCH Rewinds tape, and searches reverse scene. PLAY Begins playback. PAUSE/SLOW Pauses and slow motion and frame advance picture. CM SKIP /ZERO SEARCH In Stop mode, goes to the counter “0:00:00.“ In Play mode, skips over 1 to 3 minutes of tape. TAPE POSITION Finds out present tape position and amount of tape remaining. SPEED Selects recording speed. COUNTER RESET Resets to “0:00:00” at the desired position. SLEEP Turns off the unit automatically. NITE Color and picture intensity level are adjusted during night time use. DISPLAY Displays the VCR status and clock. RAPID TUNE Displays the last channel you were watching. VOLUME UP/DOWN Adjusts volume. SET/BACK SPACE Sets a selected menu, or goes back to correct. PROGRAM Displays SET PROGRAM screen. You can set Timer Program and On-Timer. TRACKING UP/DOWN Reduces picture noise during Playback and Slow Motion. ADD/DELETE Adds or deletes a channel. FAST FORWARD/SEARCH Fast forwards tape, and searches forward scene. SEARCH Goes directly to the desired recording. Locates end point of recording. REC Records the program. STOP Stops recording or playback. Note For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] LSQT0517A_01p09.p65 11/12/2001, 12:02 PM 6

Rear View of the Unit VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER PROG TIMER PROG TIMER Built-In Speaker AUDIO VIDEO IN Jack For dubbing. POWER See previous page. VOLUME UP/DOWN SET/BACK SPACE See previous page. CHANNEL UP/DOWN TRACKING UP/DOWN SELECT UP/DOWN See previous page. STOP/EJECT See previous page. ACTION Press together with REW. REWIND/SEARCH See previous page. ACTION Press together with STOP. PLAY See previous page. REPEAT Repeats a recording. FAST FORWARD/ SEARCH See previous page. REC See previous page. PHONES Jack Connect an earphone or headphones. PROG TIMER Indicator Lights when the unit is set for Timer Recording. ON TIMER Indicator Lights when the On-Timer is set. REC Indicator Lights during recording. Remote Sensor See above.See previous page. TIMER Sets a timer alarm up to 60 min. AC Power Plug When plugged into an AC outlet, the unit consumes 2.5 W of electric power in an OFF condition. VHF/UHF Antenna Input Terminal In from your Antenna or Cable. Page 8 [email protected] LSQT0517A_01p09.p65 11/20/2001, 9:05 AM 7

DST : ON AUTO CLOCK SET COMPLETED SETT I NG : CH 1 0 If AUTO CLOCK SET IS INCOMPLETE screen appears, set the clock using MANUAL CLOCK SET procedure as below. SET : START : ACT I ON SET CLOCK DST : ON SE SET COMPLETED COMPLETED 2 / 6 / 2 / 6 / : 2002 2002 WED WED 12 12 00 00PM PM Connections/ Initial Setup (Ready to Play) How to Connect Initial Setup (Ready to Play) 1 Plug the unit power cord into an AC wall outlet. Press Power* on the remote or unit. The unit comes on and auto channel and clock set starts. • If you use a cable box, turn it on and set it to the Public Broadcasting Service (PBS) channel in your time zone. If you use a DSS reciever, it must be turned off. Settings are made automatically. When setup is done, this screen appears. For ANT./Cable Connect the cable from Antenna/ Cable to the VHF/UHF terminal on the unit. For DSS/Cable Box Connect the OUT jack on your cable box to the VHF/UHF terminal on the unit with a RF cable. VHF/UHF VHF/UHF UNIT IN from ANT./CABLE VHF/UHF WARNING: Overtightening "Nut type" RF coaxial cables may damage jacks. Finger tighten only. Please make all cable or antenna connections before powering on. VHF/UHF VHF/UHF Cable TV Converter Box CH AUTO SET PROCEEDING PROCEEDING AUTO CLOCK SET CANCEL : PRESS STOP KEY 3 Connecting IN from ANT./CABLE 2 For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected] LSQT0517A_01p09.p65 11/20/2001, 9:05 AM 8

PROG TIMER Reset all unit Memory Functions When moving unit to a new location, or if a mistake was made in the Initial Setup section. • Make sure a tape is not inserted in the unit. Manual Clock Set If AUTO CLOCK SET was incomplete, manually set the clock as follows. SET : SELECT : END : ACT I ON SET CLOCK DST : ON SE SELE CT MONTH TH 1 / / : 1 2 Press ACTION on the Remote to display SET CLOCK Menu screen. Press to select the month and press to set. In the same manner, select and set the date, year, time, and DST. (Daylight Saving Time) SET : START : ACT I ON SET CLOCK DST : ON SE SET COMPLETED COMPLETED 2 / 6 / 2 / 6 / : 2002 2002 WED WED 12 12 00 00PM PM 3 Press ACTION twice to start CLOCK and exit. 3 1 2 Do “Initial Setup” on page 8. POWER ACTION SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN Note to CABLE System Installer This reminder is provided to call the CABLE (Cable TV) System Installers attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. [email protected] Turn the unit Power on. Press and hold both PLAY and FF on the unit for more than 5 seconds. • The power will shut off. • Please ignore “NO CASSETTE” warning. LSQT0517A_01p09.p65 11/12/2001, 12:02 PM 9

Reset Language, Channels, Clock, 4)Press and press to select and set the month, date, year, time, and DST (Daylight Saving Time). 5) Press ACTION twice to start the clock and exit this mode. 3) Press to select “ANTENNA,” then press to set your antenna system (“TV” or “CABLE”). 4) Press to select “AUTO SET,” then press . • After Channel Auto Set is finished, Clock Auto Set will be performed. (If clock is set manually, Clock Auto Set will not be performed.) (“TIME ZONE ADJUST” appears only when auto clock is set.) M A I N MENU T V VCR LANGUAGE SET : ACT I ON SELECT : T V EX I T CLOCK C H T V VCR IDIOMA T V MENU PR I NC I PAL CANAL REL OJ SAL I R HO L A F I JAR : ACT I ON ELEG I R : BONJOUR LANGUE MENU T ELE MAGNET . SORT I E HORLOGE CANAL REGLER : ACT I ON SEL. : 1) Press to select language icon. 2) Press ACTION repeatedly. For English M A I N MENU T V VCR HELLO LANGUAGE SET : ACT I ON SELECT : T V EX I T CLOCK C H For Spanish For French Language M A I N MENU T V VCR EX I T CLOCK C H LANGUAGE SET : ACT I ON SELECT : Channels Clock Press ACTION to display MAIN MENU. 3) Press to select “EXIT.” Press ACTION to exit. 1) Press to select “CH.” M A I N MENU CLOCK C H SET : ACT I ON SELECT : VCR T V EX I T LANGUAGE ANTENNA : CABLE AUTO SET CHANNEL CAPT I ON WEAK S I GNAL D I SPLAY : OFF SELECT : SET : SET END : ACT I ON SET UP CHANNEL 2) Press ACTION. M A I N MENU VCR CLOCK C H SET : ACT I ON SELECT : T V EX I T C H LANGUAGE 1) Press to select “CLOCK.” AUTO CLOCK SET MANUAL T I ME ZONE ADJUST : 0 SELECT : SET : END : ACT I ON SET CLOCK 2) Press ACTION. 1 2 3)Press to select “MANUAL” or “AUTO CLOCK SET” and press . • For Auto Clock Set, select “AUTO CLOCK SET,” then press CH . SET : START : ACT I ON SET CLOCK DST : ON 2 / 6/ 2 / 6/ : 2002 2002 WED WED 12 12 00 00PM PM SE SELE CT HOUR HOUR SELECT : LSQT0517A_10p21.p65 11/20/2001, 9:13 AM 10

3) Press to select TIME ZONE ADJUST and press or to subtract or add hour(s) as necessary. 4)Press ACTION twice to exit. (Only when Auto Clock is set.) Add or Delete a Channel Time Zone Adjust 1) Press to select “CLOCK.” M A I N MENU VCR CLOCK C H SET : ACT I ON SELECT : T V EX I T C H LANGUAGE 2) Press ACTION. AUTO CLOCK SET MANUAL T I ME E ZO ZONE ADJUS JUST T : 0 SELECT : SET : END : ACT I ON SET CLOCK AUTO CLOCK SET MANUAL T I ME E ZO ZONE ADJUS JUST T : +1 +1 SELECT : SET : END : ACT I ON SET CLOCK CHANNEL 08 ADDED To add channel: Select channel with number keys and press ADD/DLT. CHANNEL 08 DELE TED To delete channel: Select channel with CH or number keys and press ADD/DLT. ACTION key on the unit Using keys : CH UP : CH DOWN : VOLUME UP : VOLUME DOWN Whenever the menu or program screen is displayed, CHANNEL UP/DOWN function as and VOLUME UP/ DOWN function as only. On Remote On Unit On Unit You can operate the menu screen using unit buttons. To display the menu, press STOP/ EJECT and REW together with no tape inserted. To exit the menu, repeat above with or without tape inserted until normal screen appears. POWER ACTION ADD/DLT NUMBER Keys SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN STOP/EJECT STOP/EJECT REW/ REW/ ACTION ACTION VOL VOL CH CH LSQT0517A_10p21.p65 11/12/2001, 1:45 PM 11

Record On a Tape Playback a Tape 1 Insert a cassette. Press PLAY. • Playback begins if cassette has no record tab. 2 • The unit power comes on automatically. To prevent tape jam, Record tab I Stop => Press STOP I Rewind tape => Press REW in Stop mode I Fast forward tape => Press FF in Stop mode I Eject tape => Press EJECT on the remote or STOP/EJECT on the unit Ready Check List All connections are made. Your unit is plugged in. Press CH or number keys to Select Channel. • For “LINE” input, see bottom of next page. 2 3 4 • After the unit has been in Rec Pause mode for 5 minutes, it will stop automatically to protect the tape and the video head. • The remaining recording time of an OTR can be displayed by pressing DISPLAY. I Stop => Press STOP I One Touch Recording (OTR) Press REC repeatedly to set the recording length (30 min - 4 hours). • The unit stops recording at a preset time. • PROG TIMER indicator lights on the unit. 1 Insert a cassette with record tab. • The unit power comes on automatically. Notes remove loose or peeling labels from tapes. I Forward/Reverse scene search =>Press FF or REW =>Press PLAY to release. I Still (Freeze) picture =>Press PAUSE/SLOW =>Press PLAY to release. I Slow Motion picture => Hold down PAUSE/SLOW in Still mode => Press PLAY to release. I Frame by Frame picture => Press PAUSE/SLOW in Still mode => Press PLAY to release. Press SPEED to select recording speed (see page 4). SP = Standard Play LP = Long Play SLP = Super Long Play • Selected speed is displayed. Press REC to start recording. • To edit out unwanted portions, press PAUSE/SLOW to pause and resume recording. • You cannot view another channel during recording. You can operate on the unit • These features work best in SLP mode. • After the unit is in Still or Slow mode for 3 minutes, it will switch to Stop mode automatically to protect the tape and the video head. Notes Normal Rec 0:30 1:00 1:30 2:00 3:00 4:00 DISPLAY ACTION ADD/DLT NUMBER Keys EJECT PLAY STOP REC REW PAUSE/ SLOW TRACKING FF SPEED SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER PROG TIMER PROG TIMER Insert a cassette. CH PLAY REC REC Indicator Press to stop and/or eject tape LSQT0517A_10p21.p65 11/12/2001, 1:45 PM 12

• Unauthorized exchanging and/or copying of copyrighted recordings may be copyright infringement. Connections you’ll need to make. Playback (Source) 1 Recording (Editing) unit Insert pre- recorded tape. Insert blank tape with record tab. • Dubbing tapes protected with Copy Guard will have poor quality results. 2 3 4 5 Press PLAY then PAUSE at starting point to put in Standby mode. Press PLAY to start dubbing. Press STOP to stop dubbing. Select “LINE” mode. See “Selecting Input Mode” below. Press REC, then PAUSE/SLOW immediately to put in Standby mode. Press PAUSE/SLOW to start dubbing. Press STOP to stop dubbing. Selecting Input Mode Method 1: Press CH . The display will change as follows. Method 2: a Press ACTION for MAIN MENU. b Press to select “TV”, then press ACTION for SET UP TV screen. c Press to select “INPUT SELECT,” and then press to select “TUNER” or “LINE.” d Press ACTION twice to exit this mode. Caution AUDIO IN Recording (Editing) unit OUT IN IN FROM ANT. OUT TO TV AUDIO VIDEO IN Playing (Source) VCR VIDEO AUDIO IN (Perform operation of steps 4 and 5 on both units at same time.) STOP 1 2 3 125 LINE (CABLE) 69 (TV) or Our Vacation LSQT0517A_10p21.p65 11/12/2001, 1:45 PM 13

VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER PROG TIMER PROG TIMER TV Operation 1 Press POWER on the remote or unit. I Using the 100 key When selecting CABLE channels 100 to 125 with the number keys, first press the 100 key, and then enter the remaining two digits. I Rapid Tune Press R-TUNE to display the last channel you were watching. I Audio Mute Press MUTE to instantly mute the sound. Press again to restore the previous sound level. I Phones Connect an earphone (not supplied) or headphones (not supplied) to the Phones Jack. NIGHT (NITE) Mode Color and picture intensity levels are adjusted so the screen is easier on your eyes during night time use. Press NITE to set NIGHT mode. • NIGHT mode may be selected when watching TV or playing a tape. Press NITE to cancel. • Previous settings are restored. • NIGHT mode is canceled when power is turned off or power failure occurs. N I GHT Ready Check List All connections are made. Your unit is plugged in. Use CH or number keys to select a channel. 2 0 8 ABC 3 Press VOL + or VOL - to adjust volume. 24 PHONES Jack POWER VOL + / VOL- CH LSQT0517A_10p21.p65 11/12/2001, 1:45 PM 14

2 1)Press to select “TV.” 2)Press ACTION to display SET UP TV screen. 3 1)Press to select VIDEO ADJUST. 2)Press to display screen. 4 1)Press to select an adjustment item. (See below left.) 2)Press to adjust. To Reset Picture Controls. Press and to select and set “NORMAL.” All controls return to their factory settings. 5 Press ACTION three times to exit. Picture Adjustment IIIII COLOR Control Adjust color intensity. IIIII TINT Control Adjust for natural flesh tones. IIIII BRIGHTNESS Control Adjust picture brightness. I I I I I PICTURE Control Adjust picture intensity by adjusting both contrast and color level in the proper balance. I I I I I SHARPNESS Control Adjust picture sharpness. M A I N MENU T V VCR EX I T CLOCK C H LANGUAGE SET : ACT I ON SELECT : LOCK CAPT I ON I NPUT SELECT : TUNER V I DEO ADJUST FM ANTENNA :EXT SELECT : SET : END : ACT I ON SET UP TV COLOR T I NT BR I GHTNESS P I CTURE SHARPNESS NORMAL ADJUST : SELECT : END : ACT I ON COLOR T I NT BR I GHTNESS P I CTURE SHARPNESS NORMAL SET : SELECT : END : ACT I ON POWER 100 KEY RAPID TUNE MUTE VOL UP/ DOWN ACTION NITE SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN CH LSQT0517A_10p21.p65 11/20/2001, 9:20 AM 15

CH01 CH125 CH02 CH03 FM1 FM9 FM8 PLAY VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER PROG TIMER PROG TIMER 1 ON-TIMER with Alarm TV Timer Features Ready Check List The clock is set to correct time. This unit can be set to automatically power on in one of 2 modes (TV, Playback, or FM radio). You can also combine the On-Timer with a one minute alarm that gradually increases in volume. • If no button on the remote or unit (including a button used to turn off the alarm) is pressed within 60 minutes after unit turns itself on, it will turn itself back off. Press PROG to display SET PROGRAM screen. Note 2 3 1) Press to select desired settings. 2) Press to set the| ON-TIMER TIME or ON-TIMER mode. • Make sure a tape is inserted if Playback mode is selected. • See “FM Radio” on pages 20 and 21 for instructions on how to preset FM stations. • ON-TIMER mode selection order 4 Press to select ALARM “ON” or “OFF.” When “ON” is selected, an alarm will gradually increase in volume for one minute or until canceled by pressing any button (including VOL + -). To Make Corrections, use and to move back and correct. 5 Press PROG to set ON TIMER. • “ON TIMER SET” is displayed. • ON TIMER Indicator lights on the unit. To Cancel ON-TIMER set, Repeat steps 1 and 2. Then, press ADD/DLT to clear the time in step 3. Now, press PROG to end. “ON TIMER END” briefly appears on-screen. ON TIMER indicator CH TIMER 1)Press to select “ON TIMER.” 2)Press to display ON TIMER screen. SET : SET SELECT : END : T I MER SET T I MER ON T I MER S LEEP T I MER : 00 ON T I MER SELE CT HOUR 6:--AM CH -- SET : SELECT : END : PROG ALARM : ON ON T I MER SELE CT ALARM 6:00AM CH08 SET : SELECT : END : PROG ALARM : ON CANCEL : ADD / DLT ABC LSQT0517A_10p21.p65 11/20/2001, 9:20 AM 16

to set SLEEP TIMER. • Pressing DISPLAY with sleep timer set displays remaining time. Press SLEEP repeatedly until “SLEEP TIMER 00” appears to cancel. Sleep Timer This unit can be set for auto power off. SLEEP TIMER 30 SLEEP TIMER 60 SLEEP TIMER 90 SLEEP TIMER 00 Instant Alarm You can set a timer alarm up to 60 min. Useful when you are cooking, etc. 1 2 3 To cancel, press TIMER then press ADD/DLT on the remote while CANCEL/SET screen is displayed. To increase timer in progress, repeat step 2. Time will be rounded up to next 1, 5, or 10 minute interval. (See chart left.) • If current time remaining is 12:15, countdown will restart from 15:00. • If current time remaining is 9:15, countdown will restart from 10:00. Press CH on the unit with CANCEL/SET screen displayed to set alarm. (Time changes in the order shown left.) Alarm will sound at 0: 00. Press any button to stop • The volume of the alarm gradually increases for one minute and then continues to beep until any button is pressed. • Pressing TIMER repeatedly on the unit will change display as follows. Press TIMER on the unit to display the instant alarm CANCEL/SET screen. 5 : 20PM CANCEL : ADD / DLT 02 : 00 SET : CH KEY ON UN I T • While timer function is in progress, you can change channels on the unit with CH while “CANCEL/SET” screen is not displayed. Note 1:00 (one minute) 2:00 3:00 9:00 10:00 15:00 20:00 25:00 30:00 40:00 50:00 60:00 (Max) one-minute increase until 10:00 five-minute increase until 30:00 ten-minute increase until 60:00 Remaining Time SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN DISPLAY SLEEP ADD/DLT PROG FM FM LSQT0517A_10p21.p65 11/12/2001, 1:45 PM 17

OFF CAP C1 TEXT C1 CAP C2 TEXT C2 M A I N MENU T V VCR EX I T CLOCK C H LANGUAGE SET : ACT I ON SELECT : Closed Caption Mode Feature 1 2 3 4 5 Closed Caption System Closed Caption is ... This multi-use system not only allows the hearing impaired to enjoy selected programs, but also makes useful information from TV stations available to everyone. Press ACTION to display MAIN MENU. 1)Press to select “TV.” 2)Press ACTION to display SET UP TV screen. 1)Press to select “CAPTION”. 2)Press to display CAPTION screen. Press ACTION three times to return to the normal screen. 1)Press to select CAPTION MODE. 2)Press repeatedly to select mode. (See left.) CAPT I ON CA CAPT PT I ON MODE MODE : : CAP C1 CAP C1 CC ON MUTE : CAP C1 SET : SET SELECT : END : ACT I ON Closed Caption Mode Selections Caption Mode: CAP C1 or C2 A narration of selected TV programs is displayed. Check TV program listings for CC(Closed Caption) broadcasts. Caption Mode: TEXT C1 or C2 The lower half of the screen will be blocked out. When the TV station broadcasts information, such as program listings, it will appear in this space. Caption Mode: OFF Closed Caption / Text narration will not be displayed. NOTE : The closed caption or text signal may be broadcast over C1, C2, or both. Also, text contents can vary so you may wish to try different settings. Recording and Playing Back a Closed Caption/Text Program Record: Record normally. Closed Caption/ Text signal, if present, is recorded automatically. Playback: Start playback. Do above steps to select desired caption mode. LOCK CA CAPT PT I ON N I NPUT SELECT : TUNER V I DEO ADJUST FM ANTENNA :EXT SELECT : SET : END : ACT I ON SET UP TV LSQT0517A_10p21.p65 11/12/2001, 1:45 PM 18

the normal screen. NO CAP C1 CAP C2 M A I N MENU T V VCR EX I T CLOCK C H LANGUAGE SET : ACT I ON SELECT : Caption On Mute Feature Closed Caption narration, if available, is displayed when MUTE button is pressed for silence. Press ACTION to display MAIN MENU. 1)Press to select “TV.” 2)Press ACTION to display SET UP TV screen. 1)Press to select “CAPTION”. 2)Press to display CAPTION screen. 1)Press to select CAPTION MODE. 2)Press repeatedly to select “OFF.” 1)Press to select CC ON MUTE. 2)Press repeatedly to select desired mode. • Each press of will change the display as shown left. • The caption may be broadcast over CAP C1 or C2. Press MUTE to mute the sound and display closed captioning. • To cancel, press MUTE again. CAPT I ON CA CAPT PT I ON MODE MODE : : OFF OFF CC ON MUTE : CAP C1 SET : SET SELECT : END : ACT I ON LOCK CA CAPT PT I ON N I NPUT SELECT : TUNER V I DEO ADJUST FM ANTENNA :EXT SELECT : SET : END : ACT I ON SET UP TV SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN MUTE ACTION LSQT0517A_10p21.p65 11/12/2001, 1:45 PM 19

FM Radio 2 Press a number key (1~9) to select the FM number. 1 To Make Corrections, select station with a number key, then do step 3 again. To exit FM mode, press FM/TV on the remote or TIMER/FM twice on the unit. 1)Press CH to select the desired radio station. (Each press changes frequency 200 KHz.) 2)Press ADD/ DLT to set the radio station. Hold down CH or for a few seconds, then release to quickly scan for FM stations in your area. • To cancel, press CH or while in search mode. 3 FM Radio Setup 3 4 1)Press to select FM ANTENNA. 2)Press to select “INT (INTERNAL)” or “EXT (EXTERNAL)” whichever sounds the best. IIIII For cable TV users => “INT” IIIII For antenna users => “EXT” Press FM/TV on the remote or press TIMER/FM twice on the unit to display FM radio mode. FM Radio is ... This unit has an FM radio with built-in antenna, 9 station preset, and a band range of 87.5 ~ 108.1 MHz. You can even set the On-Timer (page 16) to wake up to your favorite radio station. FM ANTENNA Setup 1 2 Make sure FM tuning is done correctly (see FM Radio Setup). Press ACTION to display MAIN MENU. 1)Press to select “TV.” 2)Press ACTION to display SET UP TV screen. Press ACTION twice to end setup. FM 1 87. 5MHz 1 2 : 0 0PM FM 1 8 7. 7MHz MEMORY : PUSH ADD / DLT KEY 1 2 : 0 0PM FM 1 8 7. 7MHz MEMOR I ZED 1 2 : 0 0PM M A I N MENU T V VCR EX I T CLOCK C H LANGUAGE SET : ACT I ON SELECT : LOCK CAPT I ON V I DEO ADJUST FM ANTENNA : I NT NT SELECT : SET : END : ACT I ON SET UP TV LSQT0517A_10p21.p65 11/12/2001, 1:45 PM 20

or TIMER/FM twice on the unit. Press a Number key (1~9) to select a preset FM number (see steps 2 and 3 of FM Radio Setup on page 20.). Using FM Radio FM 1 87. 5MHz 1 2 : 0 0PM Press FM/TV on the remote or press TIMER/FM twice on the unit to display FM radio mode. VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER PROG TIMER PROG TIMER TIMER/FM Notes • FM radio cannot be recorded on a Video cassette. • You may get better reception by repositioning the unit. • You cannot select FM Radio mode during playback or record, or while a blue back screen (PROG, ACTION, MENU) is displayed. • Once stations are set, the selected station and current time are displayed when FM Radio mode is entered. To remove time, press DISPLAY. If DISPLAY is pressed again, the unit status screen appears. ADD/DLT FM/TV NUMBER Keys ACTION CH / SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN LSQT0517A_10p21.p65 11/12/2001, 1:45 PM 21

VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER VIDEO IN AUDIO IN POWER VOL CH STOP/EJECT REW/ PLAY/REPEAT FF/ REC TIMER/FM ACTION REC ON TIMER PROG TIMER PROG TIMER Press PROG (or ACTION) to end the program. To Enter More Programs, press to select and to set a blank program number, and then repeat step 3. 4 CANCEL : ADD / DLT SELECT 1 - 8 : ENTER : END : PROG / ACT I ON P DT START STOP CH SPD 1 day 9 : 00 p 12 : 00a 08 SP 2 -- -- : -- -- : -- -- -- 3 -- -- : -- -- : -- -- -- 4 -- -- : -- -- : -- -- -- Press PROG twice (or ACTION) to exit this mode. • If you’re using a cable box, make sure that it is tuned to the desired channel and the power is left on for timer recording. • PROG TIMER indicator lights on the unit. 5 Timer Recording You can set up to 8 programs to be recorded while you are away. 1 2 3 Ready Check List All connections are made. Your unit is plugged in. The clock is set to correct time. The tape is long enough. The record tab is in place. SELE CT START DATE 7 FR I --:-- --:-- -- TODAY DATE START STOP CH SLP SELECT : SET : END : PROG / ACT I ON - - - - - - - - -- - - - - - - -- - - - - - - Press PROG to display SET PROGRAM screen. 1) Press to select TIMER PROGRAMMING. 2) Press to display screen. • If a program is already in memory, press , and to select an unused program number. Press to select and or to set the recording DATE. • 1~31 = One time • DAILY = MON~FRI • WEEKLY SUN~SAT = Same time once a week Repeat step 3 to set: • start time, stop time • Channel (or LINE for outside source) • Speed (SP, LP, SLP) Today’s Date Example DAILY 7 2 1 31 6 8 9 SELECT / Selection Order WEEKLY (SAT) WEEKLY (MON) WEEKLY (SUN) PROG TIMER indicator SET : SELECT : END : PROG SET PROGRAM ON TIMER T I MER PROGRAMMING Press STOP/EJECT and REW together without a tape inserted to display MAIN MENU. Press + - to select "VCR" and STOP/EJECT and REW together to display SET UP VCR screen. Press + - to select "TIMER PROGRAM and + to display the TIMER Program Screen. Repeat main steps 3 ~ 5. You can set a Timer Recording using ACTION key on the unit. (See Page 11.) 1 2 3 4 Timer Recording Using unit Buttons LSQT0517A_22p31.p65 11/20/2001, 9:30 AM 22

1 CANCEL : ADD / DLT SELECT 1 - 8 : ENTER : END : PROG / ACT I ON P DT START STOP CH SPD 1 day day 9 9 : 00 00p 12 12 : 00 00a 08 08 SP SP 2 8 10 : 00a 12 : 00p 125 SP 3 10 8 : 00p 9 : 00p 10 SP 4 SU 9 : 00p 10 : 00p L LP 8 SAT SAT 9:00 00P P 12 12: 00 00A 08 08 TODAY ---------------------------------------------- DATE START STOP CH ABC SP SE SELE CT START START DAT ATE SELECT : SET : END : PROG / ACT I ON Press PROG twice (or ACTION) to exit this mode. 2 3 To Replace program... To Clear program... 4 Press to select the desired program. 1) Press to display. 2) Press to select and press or to set new program contents. 3) Press PROG (or ACTION). Cancel a Timer Recording: (Recording is in progress) Hold down STOP for a few seconds to cancel the Timer Recording. • Any future daily or weekly recordings will be performed as programmed. Press ADD/DLT. Review, Replace or Clear Program Contents : (Recording is not in progress) • 2 minutes before Timer recording is performed, “PLEASE PREPARE FOR TIMER REC” appears and/ or the PROG TIMER Indicator flashes. Be sure a cassette with record tab is loaded and the unit is in Stop mode. • If the start times of two programs overlap, the lower numbered program will have priority. • If the start time for a Timer Recording comes up during a normal recording or One Touch Recording (page 12), the Timer Recording will not be performed. • If there is a power interruption of more than one minute, the recording may not be performed or continued. • If “INCOMPLETE” appears after all items have been set, check all entries and make necessary corrections. Notes SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN ADD/DLT PROG STOP P DT START STOP CH SPD 1 -- -- -- -- : -- -- -- -- : -- -- -- -- -- -- 2 8 10 : 00p 12 : 00a 125 SP 3 10 8 : 00p 9 : 00p 10 SP 4 SU 9 : 00p 10 : 00p L LP SELECT 1 - 8 : ENTER : END : PROG / ACT I ON LSQT0517A_22p31.p65 11/12/2001, 2:36 PM 23

Search System is ... Each time a recording is made, an invisible index mark is placed on the tape. When timer recordings are made, program index and information are also included. These index marks can be used to access or scan recordings. Tape Operation Program End Search 1 SEARCH START : FF EX I T : SEARCH PROGRAM END SEARCH Example of Program End Search operation. Fig.1 Fig.2 Fig.3 If search exceeds a few seconds in BLANK area. Program 2 BLANK Program 1 INDEX Press SEARCH button FF 2 Press SEARCH button Index Search Go directly to the desired recording. • Make each entry within 10 seconds, or the Index Search mode will be canceled. • If Index Search is started very close to an index mark, that index mark may not be counted in the search. Notes NOTE: indicates start points of each recording. IIIII To calculate the Index Number Example 1: To go to rec. 2 from rec. 4, enter 3 and press REW. Example 2: To go to rec. 6 from rec. 2, enter 4 and press FF. 6 1 5 7 2 3 4 1 7 5 3 4 6 2 Press SEARCH twice in Playback or Stop mode to display PROGRAM END SEARCH screen . Press FF to start search. Upon locating end point... The unit searches slightly past end point, reverse searches, and plays the last few seconds of the program, then stops. • If Program End Search is started very close to an index mark, that mark may be skipped over. • To cancel, press PLAY or STOP. Locates end point of recording for continuity. End Point Notes PLAYBACK DIRECTION Program 1 Program 2 or BLANK INDEX Press SEARCH button FF End Point Program 2 BLANK INDEX BLANK Program 1 Press SEARCH button FF End Point 1 2 Press SEARCH* in Playback or Stop mode to display INDEX SEARCH screen, and then press NUMBER Keys to select the recording number. To calculate number, • see below. Press FF or REW to start search. Play begins at search end. To search forward or back 1 index, press FF or REW while screen left in displayed (10 sec.). ENTER I NDEX NUMBER : 1 US I NG 1- 9 KEYS FORWARD SEARCH : FF REVERSE SEARCH : REW NEXT : SEARCH EX I T : STOP I NDEX SEARCH FORWARD SEARCH : FF REVERSE SEARCH : REW I NDEX SEARCH LSQT0517A_22p31.p65 11/20/2001, 9:33 AM 24

PROG TIMER Auto Operation Functions Tape Position Display Press TAPE POSITION to detect current tape position. 1 DETECT I NG TAPE POS I T I ON 2 IIIII Auto Shut Off No broadcast signal in TV (Only when Weak Signal Display is set to OFF), blank tape is Played for 5 minutes => Power turns off • This feature is canceled if any button is pressed during above mode. IIIII Auto Playback Insert a tape in Power off mode => Power turns on • Playback begins if tape has no record tab. IIIII Auto Rewind Tape reaches its end => Rewind => Stop IIIII Playback Auto Eject (Repeat Play is “OFF”) Tape with no record tab reaches its end Rewind => Stop => Eject • “DETECTING TAPE POSITION” is displayed only when a cassette is first inserted and it takes several seconds for correct tape position to appear. • The present tape position indication and amount of tape remaining (according to tape speed) is displayed. • Tape remaining time display may not be precise. Press TAPE POSITION (or wait 5 seconds) to return to normal screen. • This function cannot display exact amount of tape remaining for tapes 30 minutes or less, or for tapes over 120 minutes in length. Note REW FF To find out present tape position and amount of tape remaining. Tape position is displayed for VHS-C Cassettes type, tapes under 30 minutes, and some other tapes, but the position is not correct. SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN SEARCH FF REW TAPE POSITION NUMBER Keys BEG I N END SLP R 120 MIN. LSQT0517A_22p31.p65 11/12/2001, 2:36 PM 25

Tape Operation (continued) Repeat Play Set to see a recording over and over. 1 2 1)Press to select “REPEAT PLAY.” 2)Press to set REPEAT PLAY “ON” or “OFF.” 3 M A I N MENU T V VCR EX I T CLOCK C H LANGUAGE SET : ACT I ON SELECT : 1)Press to select “VCR.” 2)Press ACTION to display SET UP VCR screen. Press ACTION to display MAIN MENU. 4 Press ACTION twice to end setup. Zero Search To quickly return to a specific tape counter location. 1 2 Press STOP. 4 5 3 Continue playback, rewind, or fast forward. Press COUNTER RESET at the desired position to reset to “0:00:00.” • Unit goes into FF or REW mode and stops at the last point the Counter was set to 0:00:00. Press DISPLAY during playback to display the Counter. • Playback repeats when tape end is reached or unrecorded portion over 30 seconds is detected. • During playback, you may also press PLAY/ REPEAT repeatedly on the unit to select REPEAT “ON” or “OFF.” Press CM/ZERO in stop mode to start ZERO SEARCH. : Present position mark : Zero position mark BEG I N END 1 : 23 : 45 BEG I N END 0 : 00 : 00 • If a blank portion exists on the tape, and depending on the position of the mark, the mark display may be out of position. Notes Press CM/ZERO repeatedly to select skip time in Play mode. • No indication appears. Commercial Skip By pressing the CM/ZERO button in Playback mode you can skip over 1 to 3 minutes of recorded tape in just a few seconds. 1 Note REPEAT REPEAT PLAY PLAY : OFF FF T I MER PROGRAMMING SELECT : SET : END : ACT I ON SET UP VCR LSQT0517A_22p31.p65 11/12/2001, 2:36 PM 26

PROG TIMER Special VCR Features When “ON” is selected, the picture is displayed even when a broadcast signal is weak or non-existent. ANTENNA : CABLE AUTO SET CHANNEL CAPT I ON WEAK S EAK S I GNAL GNAL D I SPLAY SPLAY : OFF OFF SELECT : SET : END : ACT I ON SET UP CHANNEL M A I N MENU CLOCK C H SET : ACT I ON SELECT : VCR T V EX I T LANGUAGE Weak Signal Display ON/OFF 1 2 3 • “ON” =Picture is displayed regardless of signal condition, and may not always be clearly visible. “OFF” =Screen turns solid blue when signal is absent or weak. • If unit is connected to equipment which has blue back feature, selecting “ON” will have no effect on the other equipment. VCR Lock All operations are prohibited except Timer recording and tape eject. Useful for families with small children. VCR LOCK ACT I VATED VCR LOCK OFF 4 Press ACTION to display MAIN MENU. 1)Press to select “CH.” 2)Press ACTION to display SET UP CHANNEL screen. Press ACTION twice to return to the normal screen. 1)Press to select WEAK SIGNAL DISPLAY . 2)Press to set “ON” or “OFF.” Notes • VCR Lock is canceled automatically after about 24 hours if clock is set. • “Auto Power On” is not prohibited when VCR lock is activated. In stop mode, hold down REC on the unit without a cassette inserted for 7 seconds to turn “ON.” Please ignore NO CASSETTE warning. Repeat above with or without cassette to turn “OFF.” REC SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN CM/ZERO ACTION DISPLAY COUNTER RESET LSQT0517A_22p31.p65 11/12/2001, 2:36 PM 27

Special VCR Features (continued) 1 2 Press ACTION to display MAIN MENU. Channel Caption 1)Press to select “CH.” 2)Press ACTION to display SET UP CHANNEL screen. 3 1)Press to select CHANNEL CAPTION. 2)Press to display screen. 4 5 Press ACTION four times to end setup. 1)Press to select a station. 2)Press to move cursor to the right. 3)Press to select channel number. 4)Press to set preset captions. • Repeat step 4 until the Caption List is complete. To Make Corrections Press , then to select channel number. Press to change, or ADD/DLT to delete. Channel Caption is ... Station names, e.g. ABC, TNN, etc. are set so they will appear when a channel is selected. Choose 24 preset names. ANTENNA : CABLE AUTO SET CHANNE NNEL CAP CAPT I ON ON WEAK S I GNAL D I SPLAY : OFF SELECT : SET : END : ACT I ON SET UP CHANNEL - -- -- -- - CHANNEL CAPT I ON SELECT : SET : END : ACT I ON PBS CNN ESPN HBO - -- -- -- - - -- -- -- - ABC ABC CBS FOX NBC 4 2- - 3 5- - CHANNEL CAPT I ON CLEAR : ADD / DLT SELECT : SET : END : ACT I ON TNT UPN WB DSC CBC CTV TSN GLOB 6 2 2 1 5 2 1 2 3 M A I N MENU CLOCK C H SET : ACT I ON SELECT : VCR T V EX I T LANGUAGE SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN ACTION ADD/DLT LSQT0517A_22p31.p65 11/12/2001, 2:36 PM 28

Press ACTION to display MAIN MENU. Enter Secret Code V-Chip Control Feature is... This unit has a built-in V-Chip Control which allows you to block unwanted TV usage based on US MOVIES and US TV PROGRAMS Ratings. A 4-digit code must be entered to view a blocked program or change rating settings. 1 • DO NOT forget your secret code. • Once ratings are set, restricted tapes or programs cannot be accessed unless the secret code is entered. Changing your secret code • You will need your current code. Do steps 1 ~ 4. In step 5, press ADD/DLT to clear current code. Repeat steps 4 and 5 to enter new code. 1)Press to select “TV.” 2)Press ACTION to display SET UP TV screen. 2 M A I N MENU T V VCR EX I T CLOCK C H LANGUAGE SET : ACT I ON SELECT : 1)Press to select LOCK. 2)Press to display screen. 3 1)Press number keys to enter your secret code. 2)Enter same code again for confirmation. 4 Press to display US Ratings menu (see page 30). Or Press ACTION three times to exit. 5 LOCK RECOGN I ZED CHANGE CODE : ADD / DLT CONT I NUE : END : ACT I ON CONF I RM 4-D I G I T CODE **** **** Notes Process of V-Chip Control Feature Setup Blocking Enter Code ENTER : 0 - 9 END : ACT I ON LOCK ENTER 4-D I G I T CODE ---- • Step 2) not necessary when changing rating or secret code. • Take care that you are not observed entering the secret code. To Make Corrections Press repeatedly to move the cursor. Press number keys to make the correction. LOCK LOCK CAPT I ON I NPUT SELECT : TUNER V I DEO ADJUST SELECT : SET : END : ACT I ON SET UP TV SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN ACTION ADD/DLT NUMBER Keys LSQT0517A_22p31.p65 11/12/2001, 2:36 PM 29

Enter Code 1 1)Press to select US MOVIES. 2)Press to set “ON” or “OFF.” If LOCK menu is not displayed, do “Enter Secret Code” steps on page 29. I “ON” => V-Chip Control is activated. I “OFF” => V-Chip Control is deactivated. Setup US MOVIES Ratings Note • “NEXT PAGE” displays CANADIAN V-Chip setting menu. Not necessary except when viewing Canadian tapes or broadcasts. 1 1)Press to select US TV PROGRAMS. 2)Press to set “ON” or “OFF.” Setup US TV PROGRAMS Ratings I “ON” => V-Chip Control is activated. I “OFF” => V-Chip Control is deactivated. Note • “NEXT PAGE” displays CANADIAN V-Chip setting menu. Not necessary except when viewing Canadian tapes or broadcasts. 2 1)Press to select CHANGE SETTINGS. 2)Press to display screen. 3 1)Press to select VIEW NR PROGRAMS?. 2)Press to set “YES” or “NO.” NR (Not Rated) PROGRAMS Some movies, such as old movies or foreign movies usually have no ratings. 4 Press to select and to set ratings to be blocked. (See ratings chart next page.) 5 Press ACTION to redisplay LOCK menu and continue with US TV PROGRAMS Ratings Setup (this page). Or, press ACTION four times to exit. 5 Press ACTION four times to exit this mode. NR (Not Rated) PROGRAMS Some TV shows, such as news, sports, weather, bulletins, emergency information usually have no ratings. 3 1)Press to select VIEW NR PROGRAMS?. 2)Press to set “YES” or “NO.” 2 1)Press to select CHANGE SETTINGS. 2)Press to display screen. • You may select from standard TV ratings (chart 1), or customize to a specific content rating (chart 2). 4 Press to select and to set ratings to be blocked. (See ratings charts next page.) • Ratings highlighted in Green will be blocked. Ratings in white letters will not be blocked. Note Blocking Process of V-Chip Control Feature Setup US MOVIES : OFF CHANGE SETT I NGS US TV PROGRAMS : OFF CHANGE SETT I NGS SELECT : SET : END : ACT I ON LOCK NEXT PAGE US MOVIES : OFF CHANGE SETT I NGS US TV PROGRAMS : OFF CHANGE SETT I NGS SELECT : SET : END : ACT I ON LOCK NEXT PAGE G PG PG-13 R NC-17 X V I EW NR PROGRAMS? : YES GENERAL AUD I ENCE SELECT : SET : END : ACT I ON UNLOCKED US MOVIES : OFF CHANGE SETT I NGS US TV PROGRAMS : OFF CHANGE SETT I NGS SELECT : SET : END : ACT I ON LOCK NEXT PAGE US MOVIES : OFF CHANGE SETT I NGS US TV PROGRAMS : OFF CHANGE SETT I NGS SELECT : SET : END : ACT I ON LOCK NEXT PAGE V I EW NR PROGRAMS? : YES FOR ALL CH I LDREN SELECT : SET : END : ACT I ON TV-Y TV-Y7 TV-G TV-PG TV-1 4 TV-MA FV V S L D V S L D V S L UNLOCKED TV-Y TV-Y7 TV-G TV-PG TV-1 4 TV-MA FV V S L D V S L D V S L UNLOCKED V I EW NR PROGRAMS? : YES CONTA I NS NO RAT I NG SELECT : SET : END : ACT I ON G PG PG-13 R NC-17 X V I EW NR PROGRAMS? : YES CONTA I NS NO RAT I NG SELECT : SET : END : ACT I ON UNLOCKED V-Chip Control Feature (continued) LSQT0517A_22p31.p65 11/20/2001, 9:36 AM 30

PARENTAL GUIDANCE: Some material may not be suitable for children. PARENTS CAUTIONED: Some material may be inappropriate for children under 13. RESTRICTED: Children under 17 must be accompanied by a parent or adult. OVER AGE 17 ONLY: No one 17 and under admitted. ADULTS ONLY: FV V S L D Fantasy Violence Violence Sexual Situations Adult Language Sexually Suggestive Dialogue TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA FOR ALL CHILDREN: Content specifically geared to young viewers ages 2-6. FOR AGE 7 AND OLDER: May contain mild physical or comedic violence which may frighten children under 7. GENERAL AUDIENCE: Contains little or no violence, strong language, or sexual dialogue or situations. PARENTAL GUIDANCE: May contain infrequent coarse language, limited violence, some suggestive sexual dialogue and situations. PARENTS CAUTIONED: May contain sophisticated themes, sexual situations, strong language, and more intense violence. MATURE AUDIENCE: May contain mature themes, profane language, graphic violence, and sexual situations. US TV PROGRAMS RATINGS: Chart 2 2 Blocking Message • If a program or movie exceeds the ratings you have set, a message will appear on a black background and sound is muted. To View a Blocked Program / Movie [Temporarily Deactivate V-Chip Control] Enter your secret code (ACCESS CODE) in the Blocking Message screen. • V-Chip Control is reactivated when power is turned off or power failure occurs. [Deactivate V-Chip Control] Enter your secret code (steps 1-4 page 29). Then, set US MOVIES and/or US TV PROGRAMS to “OFF” using and keys. (Ratings set on page 30 is retained and will be in effect when V-Chip Control is activated again.) Enter Code Process of V-Chip Control Feature Setup Blocking US TV PROGRAMS RATINGS:Chart 1 US MOVIES RATINGS CH08 RAT I NG : PG-1 3 ACCESS CODE ---- PROGRAM RAT I NG EXCEEDED ENTER : 0-9 SELECT/SET :CH UP :CH DOWN :VOL UP :VOL DOWN ACTION DISPLAY LSQT0517A_22p31.p65 11/12/2001, 2:36 PM 31

On-Screen Display (OSD) Warning and Instruction Displays These displays will alert you to a missed operation or provide further instructions. Press DISPLAY to display or remove the overlay. Whenever a blank section of a tape comes up in Play mode, or when the selected channel has no broadcast signal with the Weak Signal Display set to “OFF” (see page 27), the screen will turn solid blue. When a function button is pressed (PLAY, FF, etc.) or you change channels, the unit mode or channel number will be displayed. (Some station names may also appear if Channel Caption is set. See page 28.) 0 8 ABC REC 1 2 : 0 0PM 0 : 25 ABC -0 : 1 2 : 3 4 SP Function Status Current Time Rec Time Remaining (OTR mode only, see page 12.) Counter Tape Speed Channel Caption (See page 28.) VCR Status & Clock Display Blue Screen Display Channel & Function Display OSD PLEASE SET CLOCK BEFORE PROGRAMMING CHECK CASSETTE RECORD TAB TO CANCEL TIMER REC HOLD DOWN STOP KEY FOR APPROX 3 SEC NO CASSETTE PLEASE INSERT A CASSETTE PLEASE PREPARE FOR TIMER REC VIDEO HEADS MAY NEED CLEANING PLEASE INSERT HEAD CLEANING CASSETTE OR REFER TO MANUAL END: PLAY KEY VCR LOCK ACTIVATED Caution • If you attempt to set or review a Timer Recording, or set the On-Timer and the Clock is not set... • If you press REC, and a cassette is inserted with no record tab... • If you press STOP during a Timer Recording... • If you press PLAY, FF, REW, or REC without a cassette inserted... • If the unit is not in Stop mode or a cassette with record tab is not inserted two minutes before a Timer Recording is about to begin... • If head cleaning becomes necessary while playing back a tape... • If you press a function button other than STOP/EJECT or POWER while the unit is in VCR Lock mode... Page 8 - 11 3, 12 23 12 22, 23 4 27 LSQT0517A_32p40.p65 11/12/2001, 3:11 PM 32

33 Before Requesting Service Check the following points once again if you are having trouble with your unit. If you cannot resolve the problem, please call the Customer Satisfaction Center for product assistance at 1-800-211-PANA(7262) To locate an authorized servicenter call toll free 1-800-211-PANA(7262) or send e-mail to : [email protected]. Power No power… Monitor No picture or sound... Poor picture with normal sound... Poor sound with normal picture... Poor TV reception... No color or poor color... Ghost (multiple) images... TV programs cannot be watched... Channel cannot be selected... Correction • Make sure your antenna system (TV or CABLE), is correctly set. (P. 8) • Completely insert Power Plug into an AC outlet. • Set POWER button to ON. • Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in the SET UP TV menu. (P. 15) • Adjust VOLUME control. (P. 14) • Adjust SHARPNESS and PICTURE controls in the SET UP TV menu. (P. 15) • Adjust TINT and COLOR controls in the SET UP TV menu. (P. 15) • Install a directional antenna. • Make sure the selected channel is in unit’s memory. (P. 10, 11) • Only the channel being recorded can be viewed on this unit. Correction • Completely insert Power Plug into an AC outlet. • Set POWER button to ON. VCR TV program cannot be recorded... Timer recording cannot be performed… No playback picture, or the playback picture is noisy or contains streaks... VCR cannot be controlled... Correction • Make sure your antenna system (TV or CABLE), is correctly set. (P. 8) • Make sure cassette record tab is intact. (P.3) • Check that clock is set to current time and date. • Make sure DSS/CABLE box (if used) is left on and tuned to channel to be recorded. • Set recording Start/Stop times correctly. (P. 22-23) • Timer recording may not be performed or continued if a power interruption of more than 1 minute occurs before or during a Timer recording even after power is restored. • Adjust TRACKING control in either direction. (P. 4) • Try Head Cleaning. (P. 4) • Make sure VCR LOCK is set to off. (P. 27) • Make sure unit is not in a Timer Record operation. Remote Control Unit cannot be controlled... ACTION, PROG and FM/TV buttons cannot be selected... Correction • Aim remote at remote sensor on unit (P. 7) so that signal is unobstructed. • Inspect the remote batteries. (P. 3) • Make sure VCR LOCK is set to off. (P. 27) • Exposing unit remote sensor to direct fluorescent or outdoor light may cause signal interference. • Check remote batteries. Correction • Insert the cassette window side up; record tab facing you. • Completely insert Power Plug into an AC outlet. • Try ejecting or inserting the tape again after turning POWER off, then back on. • Make sure cassette record tab is intact. (P. 3) • To enable Quick Play mechanism, the VCR cylinder will rotate for about 3 minutes. This reduces response time from Stop to Play mode and from Play to Rewind Search mode. • Make sure VCR LOCK is set to off. (P. 27) Miscellaneous Video cassette cannot be inserted... Video cassette cannot be removed... Tape cannot be ejected or inserted... Video cassette ejects when a recording is started, or the power is turned off for timer recording... In Stop mode, the VCR motor (CYLINDER) continues to rotate... VCR cannot be controlled... LSQT0517A_32p40.p65 11/12/2001, 3:11 PM 33

Servicenter List As of June 2001 For Product Information, Operating Assistance, Literature Request, Dealer Locations, and all Customer Service inquires please contact: 1-800-211-PANA(7262), Monday-Friday 9am-9pm Saturday-Sunday 9am-7pm, EST. or send e-mail : [email protected] Service in Puerto Rico Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter: Ave. 65 de Infanteria. Km. 9.5 San Gabriel Industrial Park Carolina, Puerto Rico 00985 Phone (787) 750-4300 Fax (787) 768-2910 GEORGIA 8655 Roswell Road Suite 100 Atlanta, GA 30350 ILLINOIS 1709 North Randall Road Eligin, IL 60123 MASSACHUSETTS 60 Glacier Drive, Suite G Westwood, MA 02090 CALIFORNIA 6550 Katella Avenue Cypress, CA 90630 800 Dubuque Avenue S. San Francisco, CA 94080 3878 Ruffin Road Suite A San Diego, CA 92123 FLORIDA 3700 North 29th Avenue Suite 102 Hollywood, FL 33020 MINNESOTA 7850-12th Avenue South Airport Business Center Bloomington, MN 55425 OHIO 2236 Waycross Road Civic Center Plaza Forest Park, OH 45240 PENNSYLVANIA 2221 Cabot Blvd. West Suite B Langhorne, PA 19047 TEXAS 13615 Welch Road Suite 101 Farmers Branch, TX 75244 WASHINGTON 20425-84th Avenue South Kent, WA 98032 HAWAII 99-859 Iwaiwa Street Aiea, Hawaii 96701 Phone (808) 488-1996 Fax (808) 486-4369 Web Site: http://www.panasonic.com You can purchase parts, accessories or locate your nearest servicenter by visiting our Web Site. Accessory Purchases: 1-800-332-5368 (Customer Orders Only) Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032 (6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST) (Visa, Master Card, Discover Card, American Express, Check) Factory Servicenter Locations LSQT0517A_32p40.p65 11/12/2001, 3:11 PM 34

35 Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America, One Panasonic Way Secaucus, New Jersey 07094 Panasonic Sales Company, Division of Matsushita Electric of Puerto Rico, Inc. AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park Carolina, Puerto Rico 00985 PANASONIC/QUASAR Video Products Limited Warranty Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the Warrantor”) will repair or replace this product with new or refurbished parts or equivalent product, free of charge, in the USA or Puerto Rico, in the event of a defect in materials or workmanship as follows (all time periods commence from the date of the original purchase): PRODUCT CAMCORDER DVD/VCR DECK DIGITAL STILL CAMERA A/V MIXER TV/VCR, TV/DVD TV/DVD/VCR COMBINATION TV/HDR COMBINATION LABOR NINETY (90) DAYS NINETY (90) DAYS NINETY (90) DAYS NINETY (90) DAYS NINETY (90) DAYS NINETY (90) DAYS NINETY (90) DAYS CRT - NINETY (90) DAYS NINETY (90) DAYS CRT - NINETY (90) DAYS PARTS ONE (1) YEAR, EXCEPT CCD IMAGE SENSOR CCD IMAGE SENSOR - SIX (6) MONTHS ONE (1) YEAR ONE (1) YEAR, EXCEPT CCD IMAGE SENSOR CCD IMAGE SENSOR - SIX (6) MONTHS ONE (1) YEAR ONE (1) YEAR, EXCEPT CRT CRT - TWO (2) YEARS ONE (1) YEAR, EXCEPT CRT CRT - TWO (2) YEARS CONTACT NUMBER 1-800-211-PANA(7262) 1-800-211-PANA(7262) 1-800-272-7033 1-800-211-PANA(7262) 1-800-211-PANA(7262) 1-888-843-9788 SERVICE Carry-In or Mail-In Carry-In or Mail-In Carry-In or Mail-In Carry-In or Mail-In Carry-In: 21” CRT and Smaller In-Home or Carry-In: 22” CRT and Larger In-Home or Carry-In Batteries (if included) - New rechargeable batteries in exchange for defective rechargeable batteries for ten (10) days. Non-rechargeable batteries are not warranted. Tape (if included) - New video cassette tape in exchange for a defective video cassette tape for five (5) days. Memory cards (if included) - Exchange defective item for new one for ninety (90) days. In-home, carry-in or mail-in service, as applicable, in the USA can be obtained during the warranty period by contacting a Panasonic Services Company (PASC) Factory Servicenter listed in the Servicenter Directory. Or call toll free contact number listed above, to locate an authorized PASC Servicenter. Carry-in or mail-in service in Puerto Rico can be obtained during the warranty period by calling the Panasonic Sales Company telephone number listed in the Servicenter Directory. This warranty is extended only to the original purchaser. A purchase receipt or other proof of the date of the original purchase is requires before warranty service is rendered. This warranty only covers failures due to defects in materials and workmanship, which occur during normal use and does not cover normal maintenance, including, but not limited to, video and audio head cleaning. The warranty does not cover damage which occurs in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, modification, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a PASC Factory Servicenter or a PASC authorized Servicenter, or damage that is attributable to acts of God. LIMITS AND EXCLUSIONS There are no express warranties except as listed above. THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGE TO RECORDING MEDIA) RESULTING FROM THE USE OF THIS PRODUCTS, OR ARISING OUT OF ANY BREACH OF THE WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary, from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the Consumer Affairs Department at the Panasonic Consumer Electronics Company address above. SERVICE CALLS WHICH DO NOT INVOLVE DEFECTIVE MATERIALS OR WORKMANSHIP AS DETERMINED BY THE WARRANTOR, IN ITS SOLE DISCRETION, ARE NOT COVERED. COSTS OF SUCH SERVICE CALLS ARE THE RESPONSIBILITY OF THE PURCHASER. warvid 02/ 12/ 2001 Limited Warranty LSQT0517A_32p40.p65 11/12/2001, 3:11 PM 35

Spanish Quick Use Guide/Guía para rápida consulta CH AUTO SET PROCEEDING PROCEEDING AUTO CLOCK SET CANCEL : PRESS STOP KEY 2 / 6 / 2002 WED 12 : 00PM DST : ON AUTO CLOCK SET COMPLETED SETT I NG : CH 1 0 SET : START : ACT I ON SET CLOCK DST : ON SE SET COMPLETED COMPLETED 2 / 6 / 2 / 6 / : 2002 2002 WED WED 12 12 00 00PM PM MENU PR I NC I PAL TV VCR IDIOMA CANAL REL OJ SAL I R F I JAR : ACT I ON ELEG I R : F I JAC I ON AUTOMAT I CA F I JAR : ELEG I R : TERM I NAR : ACT I ON F I JAR RELOJ MANUAL AJUSTE ZONA HORA : 0 1 2 Si el ajuste automático del reloj no se ha completado, ajuste el reloj manualmente de la siguiente manera: 1) Presione la tecla ACTION en el control remoto para visualizar la pantalla del menú RELOJ. 2) Presione LM para seleccionar el mes y para ajustar. De la misma forma, seleccione y ajuste la fecha, año, hora y DST (Hora de Verano). 3) Presione dos veces la tecla ACTION para poner el RELOJ en marcha y salir. Ajustar de nuevo el reloj 1 Presione ACTION para exhiba el menú. Ajuste Manual del Reloj 2 Presione LM para seleccionar “RELOJ”. Presione ACTION. 3 Presione LM para seleccionar “MANUAL” y luego presione . 4 Presione LM y para seleccionar y ajustar la hora y la fecha. 5 Presione ACTION dos veces para que el reloj comience a funcionar y salir desde este modo. Connexiones/Configurcion Inicial Conecte por favor todas las conexiones del cable o de la antena antes de turing potencia. Conectando el cordon AC de la VCR en toma de pared iniciara automaticamente la busqueda de canales y colocacion de tiempo Para Ant./Cable Conecte Ant./Cable a la entrada de antena de la TV (VHF/UHF). Para Sistema Digital de Satelite (DSS)/ Convertidor de cable Conecte la salida del convertidor de cable la "VHF/UHF" con el RF cable. Conectando Realizando Configuracion Inicial Tape el cable electrico de la unidad en el enchufe de pared de la CA. POWER de la prensa en el telecontrol o la unidad. La unidad se adelanta y comienzo auto del canal y del reloj. Si usa convertidor de cable, enciendala y seleccione el Servicio Publico de Canales de Television (PBS) en su horario de uso o tiempo de su zona. Si utiliza receptor DSS este debe de estar apagado. Selecciones se realizaran automaticamente cuando la configuracion termine, la pantalla siguiente aparecera. Si "AUTO CLOCK SET IS INCOMPLETE" aparece en pantalla, coloque el tiempo usando el procedimiento manual (MANUAL CLOCK SET), vealo enseguida.. Por ayuda, llame al : 1-800-211-PANA(7262) o envie e-mail a : [email protected] F I JAR : ELEG I R : TERM I NAR : ACT I ON ELE ELEG I R MES ES 1 / / / / : F I JAR RELOJ VERANO : ACT LSQT0517A_32p40.p65 11/20/2001, 9:48 AM 36

37 Operaciones básicas para la reproducción 1 Inserte un casete. • El videograbador combinado se enciende automáticamente. 2 IIIII Para encontrar una escena en particular Búsqueda hacia adelante => Presione FF Búsqueda hacia atrás => Presione REW IIIII Para ver una imagen fija (congelada) => Presione PAUSE/SLOW IIIII Para ver en cámara lenta => Mantenga pulsado el botón PAUSE/SLOW en el modo de imagen fija IIIII Para ver imágenes cuadro a cuadro => Presione PAUSE/SLOW en el modo de imagen fija IIIII Para parar => Presione STOP IIIII Para rebobinar la cinta => Presione REW IIIII Para hacer avanzar la cinta rápidamente => Presione FF IIIII Para expulsar la cinta => Presione EJECT en el control remoto o STOP/EJECT en el videograbador combinado Operaciones básicas para la grabación 2 3 4 Comience la grabación. Presione REC. • Para editar partes no deseadas de una grabación, presione PAUSE/SLOW para hacer una pausa durante la grabación. • No podrá ver otro canal durante la grabación. I Para parar => Presione STOP. IIIII El videograbador combinado deja de grabar a una hora prefijada. (Grabación de un toque) Presione REC repetidamente para ajustar la hora de grabación (30 min - 4 horas.) Presione PLAY. • La reproducción comienza automáticamente si el casete no tiene la lengüeta para prevención de grabación. 1 Inserte un casete con la lengüeta para prevención de grabado. • El videograbador combinado se enciende automáticamente. Seleccione el canal. Presione CH LM o las teclas numéricas correspondiente. Seleccione la velocidad de grabación. Presione SPEED. SP = reproducción normal LP = reproducción larga SLP = reproducción super larga • La velocidad seleccionada debe aparecer en la pantalla. Grabación normal 0:30 1:00 1:30 2:00 3:00 4:00 Grabación con temporizador 1 Exhiba FIJAR PROGRAMACION. Presione PROG. Exhiba TEMPORIZADOR. 1) Presione LM para seleccionar. 2) Presione para exhibir. 2 Repita el paso 3 para ajustar: hora de comienzo, hora de parada, canal (o LINEA para una fuente exterior), velocidad (SP, LP, SLP) Ajuste la fecha de grabación. 1) Presione LM para seleccionar. 2) Presione o para ajustar. 3 5 Salga de este modo. Presione PROG dos veces (o ACTION.) • Si está usando un decodificador de TV cable, asegúrese que se encuentra en el canal deseado y que la alimentación queda conectada para grabar con temporizador. • El indicador PROG TIMER se enciende en el videograbador combinado. ELEGIR FECHA DE INICIO ELEGIR FECHA DE INICIO 7 VIE VIE --:-- --:-- --:-- --:-- ---- HOY FECHA INICIO PARADA CA SLP - - - - - - - - -- - - - - - - -- - - - - - - F I JAR : ELEG l R : TERM l NAR : PROG / ACTION 4 Termine el programa. Presione PROG (o ACTION.) 1 P FE I N I C PARADA CA VEL 2 -- -- : -- -- : -- -- -- 3 -- -- : -- -- : -- -- -- 4 -- -- : -- -- : -- -- -- ELEG I R 1-8 : CANCELAR : ADD/DLT ENTRAR : TERM I NAR : PROG / ACT I ON D I 9 : 00p 12 : 00a 08 SP • Si ya existe un programa en la memoria, presione LM y para seleccionar un número de programa sin usar. • 1 - 31 = Grabación única • DIARIO = a la misma hora de lunes a viernes • SEMANAL = a la misma hora una vez a la semana Fecha de hoy F I JAR : ELEG l R : F I JAR PROGRAMAC I ON TEMPOR l ZADOR ENCENDIDO AUTOMATICO TERM l NAR : PROG Para introducir más programas. presione LM y para seleccionar y ajustar el número de programa en blanco, y luego repita los pasos 3 y 4. LSQT0517A_32p40.p65 11/20/2001, 9:48 AM 37

Audio Mute ................................................ 14 Auto Operation Functions ......................... 25 B Batteries .......................................................3 Before Requesting Service.......................... 33 Blocking Message ....................................... 31 Blue Screen Display .................................... 32 C Caption On Mute ......................................... 19 Channel ............................................ 8 -13, 32 Channel Caption.......................................... 28 Clock .......................................................... 10 Closed Caption ........................................... 18 Commercial Skip ......................................... 26 Connections..................................................8 Connections, DSS / Cable Box ......................8 Connections, Antenna / Cable .......................8 Copy Your Tapes (Dubbing) ....................... 13 D DST (Daylight Saving Time) ..........................4 E Eject tape .................................................... 12 F Fast Forward .............................................. 12 FM Radio ............................................... 20,21 Forward Search .......................................... 12 Frame by Frame Advance .......................... 12 Front Panel Indicators ...................................7 Function Display ......................................... 32 H Head Cleaning ..............................................4 I Important Safeguards and Precautions .........2 Index Search .............................................. 24 Initial Setup ...................................................8 Input Mode .................................................. 13 INSTANT ALARM ....................................... 17 L Language .................................................... 10 Limited Warranty ......................................... 35 Location of Controls ................................ 6 - 7 N NIGHT Mode .............................................. 14 O 100 Key ...................................................... 14 One Touch Recording................................. 12 ON-TIMER with Alarm................................. 16 P Phones .................................................. 14 Playback ............................................... 12 Picture Adjustment ................................ 15 Program End Search ............................ 24 Q Quality Picture ......................................... 4 R Rapid Tune ............................................ 14 Rec(ord) ................................................ 12 Record/Playback Speed Settings ............. 4 Remote Control Buttons ........................... 6 Repeat Play ........................................... 26 Reset Language, Channels, Clock ......... 10 Reset unit ................................................ 9 Reverse Search.....................................12 Rewind................................................... 12 S Secret Code........................................... 29 Servicenter List ...................................... 34 Sleep Timer............................................ 17 Slow Motion............................................ 12 Spanish Quick Use Guide ................. 36, 37 Special VCR Features....................... 27, 28 Specifications ........................................... 4 Still Picture ............................................. 12 STOP .................................................... 12 T Tape Erasure Prevention ......................... 3 Tape Position Display............................. 25 Time Zone Adjust ................................... 11 Timer Program Review, Replace, Clear . 23 Timer Recording .................................... 22 Timer Recording Cancellation ................ 23 TV Operation ......................................... 14 TV Timer Features ............................ 16, 17 U Unit, Front/Rear view ............................... 7 US MOVIES/TV PROGRAMS Ratings ... 31 V VCR Lock .............................................. 27 VCR Status & Clock Display .................. 32 V-Chip Control Feature ................... 29 - 31 W Warning and Instruction Displays ........... 32 Weak Signal Display ON/OFF ................ 27 Z Zero Search........................................... 26 INDEX Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America One Panasonic Way Secaucus, New Jersey 07094 Panasonic Sales Company (“PSC”), Division of Matsushita Electric of Puerto Rico, Inc. Ave. 65 de Infanteria. Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Printed in U.S.A LSQT0517A M0901-0 P LSQT0517A LSQT0517A_32p40.p65 11/20/2001, 9:49 AM 40