Sony MZ-NHF800 Service Manual

MiniDisc digital audio system Laser diode properties Material: GaAlAs Wavelength: λ = 790 nm Emission duration: continuous Laser output: less than 44.6 µW (This output is the value measured at a distance of 200 mm from the lens surface on the optical pick-up block with 7 mm aperture.) Recording and playback time When using HMD1G (1GB disc): Maximum 34 hours in Hi-LP stereo When using MDW-80 in Hi-MD mode: Maximum 10 hours and 10 min. in Hi-LP stereo When using MDW-80 in MD mode: Maximum 160 min. in monaural Maximum 320 min. in LP4 stereo Revolutions 350 rpm to 3,000 rpm (CLV) Error correction Hi-MD: LDC (Long Distance Code)/BIS (Burst Indicator Subcode) MD: ACIRC (Advanced Cross Interleave Reed Solomon Code) Sampling frequency 44.1 kHz Sampling rate converter Input: 32 kHz/44.1 kHz/48 kHz Coding Hi-MD: ATRAC3plus (Adaptive TRansform Acoustic Coding 3 plus) MD: ATRAC ATRAC3 −− LP2/LP4 Modulation system Hi-MD: 1-7RLL (Run Length Limited)/PRML (Partial Response Maximum Likelihood) MD: EFM (Eight to Fourteen Modulation) Frequency response 20 to 20,000 Hz ± 3 dB Inputs MIC: stereo mini-jack (minimum input level 0.13 mV) LINE IN (OPT)1): stereo mini-jack for analog input (minimum input level 49 mV) optical (digital) mini-jack for optical (digital) input Outputs i2): stereo mini-jack (dedicated remote control jack) Maximum output (DC) Headphones: 5 mW + 5 mW (24 Ω) (USA model) 3 mW + 3 mW (16 Ω) (European models) 5 mW + 5 mW (16 Ω) (Other models) Radio (MZ-NHF800) Frequency range USA model: FM: 87.5 - 108.0 MHz AM: 530 - 1,710 kHz (10 kHz step) 531 - 1,710 kHz (9 kHz step) TV: 2 - 13 CH WEATHER: 1 - 7 CH Canadian model: FM: 87.5 - 108.0 MHz AM: 530 - 1,710 kHz (10 kHz step) 531 - 1,710 kHz (9 kHz step) Models for Europe and China: FM: 87.5 - 108.0 MHz AM: 531 - 1,602 kHz Other models: FM: 87.5 - 108.0 MHz AM: 530 - 1,710 kHz Antenna FM/TV/WEATHER: Headphones/earphones cord antenna AM: Built-in ferrite bar antenna General Power requirements Sony AC Power Adaptor connected at the DC IN 3V jack: 120 V AC, 60 Hz (Models for USA, Canada, Mexico, and Taiwan) 230 V AC, 50/60 Hz (Models for continental Europe and Chile) 240 V AC, 50 Hz (Model for Australia) 230 V AC, 50 Hz (Models for U.K. and Hong Kong) 115 V/230 V AC, 50/60 Hz (Other models in MZ-NHF800) 100 - 240 V AC, 50/60 Hz (Other models in MZ-NH700) The recorder: Nickel metal hydride rechargeable battery NH-7WMAA 1.2V 700 mAh (MIN) Ni-MH LR6 (size AA) alkaline battery AC power adaptor DC 3V Operating temperature +5°C (+41°F) to +35°C (+95°F) Dimensions Approx. 81.0 × 29.2 × 78.9 mm (w/h/d) (31/4 × 113/16 × 31/8 in.) (excluding projecting parts and controls) Mass Approx. 103 g (3.7 oz) (the recorder only) Approx. 122 g (4.4 oz) (including the rechargeable battery) 1)The LINE 2)Measured in accordance with JEIAT. IN (OPT) jack is used to connect either a digital (optical) cable or a line (analog) cable. PORTABLE MINIDISC RECEIVER MZ-NH700/NHF800 Ver 1.1 2004.09 SPECIFICATIONS – Continued on next page – 9-879-056-02 2004I05-1 © 2004.09 Sony Corporation Personal Audio Company Published by Sony Engineering Corporation US and foreign patents licensed from Dolby Laboratories Licensing Corporation. Model Name Using Similar Mechanism NEW MD Mechanism Type MT-MZNH900-181 Optical Pick-up Name ABX-U US Model MZ-NHF800 Canadian Model AEP Model UK Model E Model Australian Model MZ-NH700/NHF800 Chinese Model Tourist Model MZ-NH700 • SonicStage and SonicStage logo are trademarks or registered trademarks of Sony Corporation. • MD Simple Burner, OpenMG, “Magic Gate”, “MagicGate Memory Stick”, “Memory Stick”, Hi-MD, Net MD, ATRAC, ATRAC3, ATRAC3plus and their logos are trademarks of Sony Corporation. • Microsoft, Windows, Windows NT and Windows Media are trademarks or registered trademarks of Microsoft Corporation in the United States and /or other countries. • IBM and PC/AT are registered trademarks of International Business Machines Corporation. • Macintosh is a trademark of Apple Computer, Inc. in the United States and/or other countries. • MMX and Pentium are trademarks or registered trademarks of Intel Corporation. • All other trademarks and registered trademarks are trademarks or registered trademarks of their respective holders. Photo: MZ-NHF800

Supplied accessories AC power adaptor (1) Remote control (1) Headphones (for USA model) (1) Dedicated USB cable (1) Earphones (except USA model) (1) NH-7WMAA Nickel metal hydride rechargeable battery (1) CD-ROM (SonicStage/MD Simple Burner (1)* Battery carrying case (1) Hi-MD mode (When using a 60/74/80-minute standard disc) (Unit: approx.hours)(JEITA) Battery life When recording continuously Hi-MD mode (When using a 1GB Hi-MD disc) (Unit: approx.hours)(JEITA3)) 3) Measured in accordance with the JEITA (Japan Electronics and Information Technology Industries Association) standard. Batteries Linear PCM Hi-SP Hi-LP NH-7WMAA 4) 4) When using a 100% fully charged nickel metal hydride rechargeable battery 3 4.5 5 LR65) 5) When using a Sony LR6 (size AA) “STAMINA” alkaline dry battery (produced in Japan) 2.5 3.5 4.5 Batteries Linear PCM Hi-SP Hi-LP NH-7WMAA 2.5 4.5 5.5 LR6 5 8 9.5 On power sources •For use in your house: use the AC power adaptor supplied with this recorder. Do not use any other AC power adaptor since it may cause the recorder to malfunction. Polarity of the plug Clamp filter (2) Carrying pouch (except USA model) Optical cable (MZ-NH700) (except Canadian andMexican Models) (1) *Do not play a CD-ROM on an audio CD player. MD mode (Unit: approx.hours)(JEITA) When playing continuously Hi-MD mode (When using a 1GB Hi-MD disc) (Unit: approx.hours)(JEITA) Hi-MD mode (When using a 60/74/80-minute standard disc) (Unit: approx.hours)(JEITA) MD mode (Unit: approx.hours)(JEITA) When using the radio (MZ-NHF800) (Unit: approx.hours)(JEITA) Batteries SP Stereo LP2 Stereo LP4 Stereo NH-7WMAA 4.5 6 6.5 LR6 7.5 9.5 11 Batteries Linear PCM Hi-SP Hi-LP NH-7WMAA 4.5 7.5 9 LR6 11 18.5 21.5 Batteries Linear PCM Hi-SP Hi-LP NH-7WMAA 4 7.5 9 LR6 9.5 17 20 Batteries SP Stereo LP2 Stereo LP4 Stereo NH-7WMAA 7.5 9 10 LR6 20.5 24 26 Batteries FM/AM TV/Wb (weather)6) 6) USA model only. NH-7WMAA 7.5 7 LR6 18.5 17 Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 ˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

1. SERVICING NOTES ................................................ 4 2. GENERAL Location of Controls........................................................ 5 3. DISASSEMBLY 3-1. Disassembly Flow ........................................................... 6 3-2. Case (Lower) Section ...................................................... 7 3-3. MAIN Board.................................................................... 7 3-4. Case (Upper) Section....................................................... 8 3-5. Mechanism Deck Section (MT-MZNH900-181), MD Standard Pin ............................................................. 8 3-6. Set Chassis Assy .............................................................. 9 3-7. Gear (BSA), Gear (SB) ................................................... 9 3-8. Op Service Assy .............................................................. 10 3-9. DC Motor SSM18D/C-NP (Spindle) (M701), DC Motor (Sled) (M702), DC Motor Unit (Over Write Head Up/Down) (M703) ............................. 10 3-10. Holder Assy ..................................................................... 11 3-11. Position of Ferrite Core ................................................... 11 4. TEST MODE .............................................................. 12 5. ELECTRICAL ADJUSTMENTS ......................... 16 6. DIAGRAMS 6-1. Block Diagram –MD SERVO Section – ......................... 21 6-2. Block Diagram –AUDIO Section – ................................. 22 6-3. Block Diagram –POWER SUPPLY Section – ................ 23 6-4. Schematic Diagram –MAIN Section (1/9) – ................... 25 6-5. Schematic Diagram –MAIN Section (2/9) – ................... 26 6-6. Schematic Diagram –MAIN Section (3/9) – ................... 27 6-7. Schematic Diagram –MAIN Section (4/9) – ................... 28 6-8. Schematic Diagram –MAIN Section (5/9) – ................... 29 6-9. Schematic Diagram –MAIN Section (6/9) – ................... 30 6-10. Schematic Diagram –MAIN Section (7/9) – ................... 31 6-11. Schematic Diagram –MAIN Section (8/9) – ................... 32 6-12. Schematic Diagram –MAIN Section (9/9) – ................... 33 6-13. Printed Wiring Board –MAIN Section (1/2) – ................ 34 6-14. Printed Wiring Board –MAIN Section (2/2) – ................ 35 7. EXPLODED VIEWS 7-1. Case (Lower) Section ...................................................... 47 7-2. Case (Upper) Section....................................................... 48 7-3. Chassis Section ................................................................ 49 7-4. Mechanism Deck Section (MT-MZNH900-181) ............ 50 6. ELECTRICAL PARTS LIST ................................ 51 Ver 1.1

break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT SL894 (OPEN/CLOSE) – MAIN Board (Conductor Side) – UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40 °C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. Providing the required system environment The following system environment is required in order to use the SonicStage/MD Simple Burner software for the MD Walkman. This software is not supported by the following environments: •OSs other than the indicated above •Personally constructed PCs or operating systems •An environment that is an upgrade of the original manufacturer-installed operating system •Multi-boot environment •Multi-monitor environment •Macintosh •We do not ensure trouble-free operation on all computers that satisfy the system requirements. •The NTFS format of Windows XP/Windows 2000 Professional can be used only with the standard (factory) settings. •We do not ensure trouble-free operation of the system suspend, sleep, or hibernation function on all computers. •For Windows 2000 Professional users, install Service Pack 3 or later version before using the software. System requirements Computer IBM PC/AT or Compatible • CPU: Pentium II 400 MHz or higher (Pentium III 450 MHz or higher is recommended.) • Hard disk drive space: 200 MB or more (1.5 GB or more is recommended) (The amount space will vary according to Windows version and the number of music files stored on the hard disk.) • RAM: 64 MB or more (128 MB or more is recommended) Others • CD drive (capable of digital playback by WDM) • Sound Board • USB port (supports USB (previously USB 1.1)) Operating System Factory installed: Windows XP Media Center Edition 2004/Windows XP Media Center Edition/Windows XP Professional/Windows XP Home Edition/ Windows 2000 Professional/Windows Millennium Edition/Windows 98 Second Edition Display High Color (16bit) or higher, 800 × 600 dots or better (1024 × 768 dots or better is recommended) Others • Internet access: for Web registration, EMD services and CDDB • Windows Media Player (version 7.0 or higher) installed for playing WMA files Notes OPERATION CHECK WHEN THE LID IS OPEN In making an operation check with the MAIN Board removed from the set, short the SL894 (OPEN/CLOSE) of the MAIN Board with the solder before starting the operation check. Note: Be sure to remove the solder used for shortcircuit after the repaire completed.

instruction manual. Looking at controls The recorder A Display window B T MARK/REC (+N) button C Jog dial D 5-way control key E DC IN 3V jack F X (pause) button G x (stop) • CANCEL/CHG button H OPEN switch I GROUP button J •NAVI/ MENU button Press lightly to go to the NAVI (navigation) setting mode. Press for 2 seconds or more to go to MENU setting mode. K USB cable connecting jack 1 4 3 qs qd qf qg 2 5 6 7 qa 9 8 q; Operation Function Press NENT 1) play, enter Press towards . find the beginning of the previous track, rewind Press towards > find the beginning of the next track, fast forward Press towards VOL +1) or VOL −. volume 1) There are tactile dots beside the NENT and VOL + buttons. L LINE IN (OPT) jack M MIC (PLUG IN POWER) jack There is a tactile dot beside the MIC (PLUG IN POWER) jack. N HOLD switch Slide the switch in the direction of the arrow to disable the buttons on the recorder. To prevent the buttons from being accidentally operated when you carry the recorder, use this function. O i (headphones/earphones) jack The display window of the recorder A Character information display Displays the disc and track names, date, error messages, track numbers, etc. B SYNC (synchro-recording) indication C Hi-MD/MD indication “Hi-MD” lights up when the operation mode of the recorder is in Hi-MD mode and “MD” lights up when the operation mode is in MD mode. D REC indication Lights up during recording or file transfers from the computer. When flashing, the recorder is in record standby mode. E Battery indication Shows the approximate remaining battery power. If the battery is weak, the indication becomes empty and starts flashing. F Disc indication Shows that the disc is rotating for recording or playing. G Track mode (PCM, Hi-SP, Hi-LP, SP, LP2, LP4, MONO) indication H Sub play mode/Repeat play indications Shows the selected Sub play mode (single-track play, shuffle play, etc.) or Repeat play. I Main play mode indications Shows the selected main play mode (group play, bookmark play, etc.). 1 2 3 4 5 6 7 8 9 The headphones/earphones with a remote control (MZ-NHF800) A VOL +, − buttons Press to adjust the volume. B Jog lever (NX/ENT, ., > • BAND, TUNE −, TUNE +) When using an MiniDisc When using the radio C Display window D x (stop) button E (group) +, − F RADIO ON/OFF button Press to turn on or off the radio. G Clip H HOLD switch To prevent the buttons from being accidentally operated when you carry the recorder, use this function. I DISPLAY button J P-MODE/ button K SOUND button B C D E A F G H I J K Operation Function Press NX/ENT play, pause, enter Slide towards . find the beginning of the previous track, rewind Slide towards > find the beginning of the next track, fast forward Operation Function Press BAND select a band Slide towards TUNE − tune backwards Press towards TUNE + tune forward The display window of the remote control (MZ-NHF800) A Disc indication B PRESET indication C Character information display D Sub play mode/Repeat play indications E SND (sound) and SUR (surround) indications F Battery level indication G Track number/Band/Preset number display H Main play mode indications 1 2 3 4 8 7 6 5 The headphones/earphones with a remote control (MZ-NH700) A Clip B HOLD switch To prevent the buttons from being accidentally operated when you carry the recorder, use this function. C (group) +, − buttons D Volume control (VOL +, −) Turn to adjust the volume. E NX (play, pause) button F x (stop) button G ., > buttons 1 4 5 6 7 3 2 Operation Function Press . find the beginning of the previous track, rewind Press > find the beginning of the next track, fast forward

3-1. DISASSEMBLY FLOW 3-2. CASE (LOWER) SECTION (Page 7) 3-3. MAIN BOARD (Page 7) 3-4. CASE (UPPER) SECTION (Page 8) 3-5. MECHANISM DECK SECTION (MT-MZNH900-181), MD STANDARD PIN (Page 8) 3-7. GEAR (BSA), GEAR (SB) (Page 9) 3-8. OP SERVICE ASSY (Page 10) 3-11. POSITION OF FERRITE CORE (Page 11) 3-9. DC MOTOR SSM18D/C-NP (SPINDLE) (M701), DC MOTOR (SLED) (M702), DC MOTOR UNIT (OVER WRITE HEAD UP/DOWN) (M703) (Page 10) 3-10. HOLDER ASSY (Page 11) 3-6. SET CHASSIS ASSY (Page 9) SET Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed. SECTION 3 DISASSEMBLY Ver 1.1

(CN471) 4 three screws (M1.4) 1 Remove two solders of over write head flexible board. 6 OP flexible board (CN501) 3 motor flexible board (CN701) 7 MAIN board 4 screw (M1.4) 5 2 Remove the case (lower) section in the direction of the arrow. 1 two screws (M1.4) 1 two screws (M1.4) 3-2. CASE (LOWER) SECTION

3-5. MECHANISM DECK SECTION (MT-MZNH900-181), MD STANDARD PIN 1 LCD module flexible boaed (CN471) 7 case (upper) section 6 boss 3 herical torsion spring (L) 2 Open the case (upper) section. 4 two step screws 5 2 mechanism deck section (MT-MZNH900-181) 3 MD standard pin 1 two step screws (MD)

3-7. GEAR (BSA), GEAR (SB) 1 torsion coil spring (R) 2 extension spring (R) 5 two screws 3 compression coil spring (open) 4 open slider 6 battery case 7 set chassis assy 1 self tap screw 2 thrust retainer spring 3 washer (0.8-2.5) 4 gear (BSA) 5 gear (SB)

3-9. DC MOTOR SSM18D/C-NP (SPINDLE) (M701), DC MOTOR (SLED) (M702), DC MOTOR UNIT (OVER WRITE HEAD UP/DOWN) (M703) 1 Lead screw block assy is turned and it removes from OP service assy. 2 OP service assy 3 two screws (M1.4) 4 DC motor (sled) (M702) 1 Remove four solders of flexible board. 2 Remove two solders of flexible board. 6 three self tap screws 7 DC motor SSM18D/C-NP (spindle) (M701) 5 motor base assy 9 DC motor unit (over write head up/down) (M703) 8 self tap screw

4 Remove the holder assy to the direction of the arrow A. 3 Open the holder assy. 1 boss 2 boss A 3-11. POSITION OF FERRITE CORE A cable is rolled once. USB A type USB mini B type A cable is not rolled. A cable is rolled once. clamp filter (ferrite core) (Part No. 1-543-798-31) A cable is rolled twice. -REMOTE CONTROL UNIT- -AC ADAPTOR- -USB CABLE- A cable is rolled once. A cable is rolled once. clamp filter (ferrite core) (Part No. 1-543-798-31) clamp filter (ferrite core) (Part No. 1-543-793-41) 20mm Remote control unit (RM-MC21, RM-MC39LT, RM-MC40ELK) (RM-MC21, RM-MC40ELK) A cable is rolled once. clamp filter (ferrite core) (Part No. 1-543-793-41) clamp filter (ferrite core) (Part No. 1-543-793-41) clamp filter (ferrite core) (Part No. 1-543-793-41) clamp filter (ferrite core) (Part No. 1-543-793-41) clamp filter (ferrite core) (Part No. 1-543-793-41) clamp filter (ferrite core) (Part No. 1-543-793-41) 20mm 20mm 20mm 25mm 40mm 40mm 40mm 40mm 40mm (RM-MC39LT) (AC-ES3010K) (AC-ET307K) Ver 1.1

key. 1. ENTERING THE TEST MODE Preparation: Copy the “TestMode_Enter_For_900_800_700_600_600D_ Ver***.exe” folder of the PC application of the latest version to your PC in advance. (operating system: Windows 2000, Windows XP) Also, when using this application, the SonicStage Ver. 2.0 or 2.1 is necessary, and install it in your PC in advance. Procedure: 1. If a Simple Burner has run on the PC, finish it (including the one that is resident in the task tray). 2. Start the “TestMode_Enter_For_900_800_700_600_600D_ Ver***.exe”. 3. Insert the fully charged Ni-MH rechargeable battery (NH- 7WMAA). 4. Open and close the top panel of the main unit to wait until the system reading finished. 5. Connect the main unit and PC by USB cable. 6. Check by device manager screen from property of “My computer” that the set is recognised to your PC normally. 7. Click the [Enter TestMode] button on the screen of application 8. Disconnect the USB cable, when “OK” message is displayed on the application screen. 9. Remove the battery. Screen of the PC application “TestMode_Enter_For_900_800_ 700_600_600D_Ver***.exe” (“***” is version number) Note: Once the test mode is activated with this application, the test mode is then activated forcibly by only turning on the power. After the repair completed, be sure to release the test mode by using this application once more. 2. OPERATION IN SETTING THE TEST MODE • When the test mode becomes active, first the Display Check mode is selected. • Other mode can be selected from the Display Check mode. • When the test mode is set, the LCD repeats the following display. Display check mode: “00#”: Model type 005 (MZ-NH700) 004 (MZ-NHF800) “*.***”: Microcomputer version • When the X key is pressed and hold down, the display at that time is held so that display can be checked. 3. RELEASING THE TEST MODE Procedure: 1. If a Simple Burner has run on the PC, finish it (including the one that is resident in the task tray). 2. Start the “TestMode_Enter_For_900_800_700_600_600D_ Ver***.exe”. 3. Insert the fully charged Ni-MH rechargeable battery (NH- 10WM). 4. Open and close the top panel of the main unit to wait until the system reading finished. 5. Connect the main unit and PC by USB cable. 6. Check by device manager screen that the set is recognised to your PC normally. 7. Click the [Exit TestMode] button on the screen of application 8. Disconnect the USB cable, when “OK” message is displayed on the application screen. 9. Remove the battery. Hi-MD 24 SYNC All lit All off Microcomputer version display Hi-SPLP PCMMONO 1SHUFA-B PGM REC 00# Ver *.*** Ver 1.1

This is mode to adjust or check the operation of the set by function. Operation of The Manual Mode 1. Enter the test mode (Display Check mode). 2. Press the [VOL+] key to activate the Manual mode where the LCD displays as shown below. Display 3. During each test, the optical pick-up moves outward or inward while the > or . key is pressed for several seconds respectively. 4. Each test item is assigned with a four-digit item number; 1000th place is a top item, 100th place is a major item, 10th place is a medium item, and unit place is a minor item. The values adjusted in the test mode are written to the non- volatile memory (for the items where adjustment was made). 5. To quit the Manual mode, press the x key and return to the Display Check mode. Flow of manual mode operation: 0 Manual Number of 1000th place x key > key Top item switching Major item switching x key > key [VOL +] key: 1000th place of item number increase. [VOL --] key: 1000th place of item number decrease. [VOL +] key: 100th place of item number increase. [VOL --] key: 100th place of item number decrease. Medium item switching x key > key [VOL +] key: 10th place of item number increase. [VOL --] key: 10th place of item number decrease. Minor item switching > . key: 1st place of item number increase. key: 1st place of item number decrease. [VOL +] key: Increases the adjusted value. [VOL --] key: Decreases the adjusted value. Adjusted value variation Adjusted value write key: Adjusted value is written. X 4. CONFIGURATION OF THE TEST MODE Flow of the test mode: Manual Mode Sound Skip Check Result Display Mode (Play) Display Check Mode Version display → All lit → All off → Version display... [VOL +] key x key x key N ENT key Self-Diagnosis Result Display Mode x key > key Sound Skip Check Result Display Mode (REC) x key [T MARK] key or [REC] switch Key Check Mode [GROUP] key Overall Adjustment Mode [VOL --] key x key > . key or Open the lid Key Count Mode [NAVI/MENU] key (press a few seconds) (Not used in servicing) 0 AdjF** 00# Ver *.*** 0 Manual 114 10 0 1 0000 0 P00r00 0 p00R00 001 MENU 000 Ver 1.1

6-1. Operation of The Overall Adjustment Mode 1. Enter the test mode (Display Check mode). 2. Press the [VOL--] key to activate the Overall Adjustment mode where the LCD displays as shown below. Display Disc mark: Lit the inner segments: Completed the power supply adjustment. Lit the outer segments: Completed the charge function check. “**”: If “DF” or “FF” is displayed, it mean that completed the servo overall adjustment. 3. To quit the Overall Adjustment mode, press the x key and return to the Display Check mode. Flow of overall adjustment mode: 0 AdjF** CD Overall Adjustment Mode Optical Pick-up Operation Check Mode Overall Adjustment Mode x key x key Stray Light Offset Overall Adjustment Mode x key x key > key . key Initialize The Adjustment Values (rotation) x key [T MARK] key or [REC] switch Hi-MD3 Overall Adjustment Mode [GROUP] key MD1 Overall Adjustment Mode [VOL +] key [VOL --] key x key *** MD1Run 0 AdjF** *** CD Run *** HM3Run *** OfsRun 000 OPChk 911 ResOK? 6-2. Error Message in The Overall Adjustment Mode In the Overall Adjustment mode, if an error occurred, it displays as following table. Display Description Close! Dose not close the lid DfDis! Unsuitableness disc was inserted NoChg! Does not finish the charge function check NoTmp! Does not setting the temperature correction value NotCD! Does not complete the CD Overall adjustment beforethe MD1 Overall adjustment NotM1! Does not complete the MD1 Overall adjustment before the Hi-MD3 Overall adjustment NotH3! Does not complete the Hi-MD3 Overall adjustment before the Stray Light Offset Overall adjustment ****NG Error of item number “****” 7. SELF-DIAGNOSIS RESULT DISPLAY MODE This set uses the self-diagnostic function system in which if an error occurred during the recording or playing, the mechanism control block and the power supply control block in the microcomputer detect it and record its cause as history in the nonvolatile memory. By checking this history in the test mode, you can analyze a fault and determine its location. Total recording time is recorded as a guideline of how long the optical pick-up has been used, and by comparing it with the total recording time at the time when an error occurred in the self- diagnosis result display mode, you can determine when the error occurred. Clear the total recording time, if the optical pick-up was replaced. 7-1. Operation of The Self-Diagnosis Result Display Mode 1. Enter the test mode (Display Check mode). 2. Press the > key to activate the Self-Diagnosis Result Display mode where the LCD displays as shown below. Display “***” : Error code “$$” : Error history code “###” : Total recording time 3. To quit the Self-Diagnosis Result Display mode, press the x key and return to the Display Check mode. *** $$#### Ver 1.1

888 RMC OK ## Flow of Self-diagnosis Result Display mode operation: 7-2. Error Code of The Self-Diagnosis Result Display Mode Error code Description 00 No error 01 Attempt to access an abnormal address 02 High temperature detected 03 Focus error (no change) 04 Abnormal rotation of disc 05 Fault of disc discriminate 06 Error of access loop (no change) 07 Error of access loop (with change) 08 Could not read address 09 Focus error (with change) 12 Could not read data with SYNC 13 TOC address data error 32 Focus error, ABCD offset error 33 Tracking error, offset error 34 Tracking error, X1 tracking error, offset error 7-3. Clear The Total Recording Time After replacing the optical pick-up, clear the total recording time. 1. Enter the test mode (Display Check mode). 2. Press the > key to activate the Self-Diagnosis Result Display mode. 3. Press the [VOL--] key once to display the total recording time indication. 4. Press the X key and display “ClrOK?”. 5. Press the X key again to display “RecT 0” and clear the total recording time. 8. KEY CHECK MODE This mode is used for key check. Operation of The Key Check Mode 1. Enter the test mode (Display Check mode). 2. Press the [GROUP] key to activate the Key Check mode where the LCD displays as shown below. Display “*” : Remote commander (0: with, 4: without) “$$$$$$” : Pressed key name. When remote commander key is pressed, display becomes as “r$$$$$”. When the jog dial is turned, it displays “JOG+ X” or “JOG- X” (“X” is number of 1 to 3). If the jog dial is turned four click, it displays “JOG+OK” or “JOG-OK”. “##” : Key voltage of remote commander. (Hexadecimal number) 3. When all keys (*1) check is OK on the main unit, it displays as follows. Display When all keys (*1, 2) check is OK on the remote commander, it displays as follows. Display *1) Turn the jog dial four click clockwise and counterclockwise to jog test is OK. *2) [RADIO ON/OFF] key (MZ-NHF800) is not included in this check. 4. When all keys check are OK both the main unit and the remote commander, it display backs to the Display Check mode automatically. 5. To quit the Key Check mode, open the lid and return to the Display check mode. The first error [VOL +] key [VOL --] key *** 1 #### The last error [VOL +] key [VOL --] key *** N #### One error before the last [VOL +] key [VOL --] key *** N1#### Two error before the last [VOL +] key [VOL --] key *** N2#### Total recording time [VOL +] key [VOL --] key *** R_#### Ver 1.1

1. Adjustment must be done in the test mode only. After adjusting, release the test mode. A key having no particular description in the text, indicates a set key. 2. Use the following tools and measuring instruments. • Digital voltmeter • Regulated dc power supply (two sets) • Thermometer (using the Temperature Correction) • Laser power meter • CD adjustment disc TDYS-1 (Part No. : 4-963-646-01) • MD1/HiMD1 hybrid adjustment disc MDW-74/GA1 (Part No. : 4-229-747-01) • Hi-MD3 adjustment disc HMD1GSDJ (Part No. : 7-819-098-37) *1 • Remote commander in accessories (with LCD) • AC adapter in accessories • Ni-MH rechargeable battery (NH-7WMAA) in accessories (full charged) • PC application software for test mode “TestMode_Enter_For_900_800_700_600_600D_Ver***.exe” *2 • USB cable *1) Hi-MD3 adjustment disc (HMD1GSDJ) is consumable. Therefore if it is used 400 times, exchange it for a new. *2) Use the newest version every time. Copy the whole folder of this program to your PC. Operating system: Windows 2000, Windows XP When using this application, the SonicStage Ver. 2.0 or 2.1 is necessary, and install it in your PC in advance. 3. Unless specified otherwise, supply DC 1.5 V from battery terminals (CL431: BATT+, CL432: BATT–). 2. ADJUSTMENT SEQUENCE Adjustment must be done with the following order. Adjustment order: 1. Entering the test mode 2. Initialize the adjustment value 3. Setting the temperature correction value 4. Power supply voltage adjustment 5. Charge function check 6. Laser power check 7. Setting the adjustment values 8. Servo Overall adjustment 9. Resume clear 10. Releasing the test mode 3. ADJUSTMENT OF THE EACH ITEM 3-1. Entering The Test Mode Refer to the “SECTION 4. TEST MODE”. 3-2. Initialize The Adjustment Value Procedure: 1. In the test mode (Display Check mode), press the [VOL--] key to enter the Overall adjustment mode. 2. Press the [T MARK] key and display “911 ResOK?”. 3. Press the X key to display “911 Reset!” and initialize the adjustment values. 4. Press the x key and back to Display Check mode. 3-3. Setting The Temperature Correction Value Procedure: 1. In the test mode (Display Check mode), press the [VOL+] key to enter the Manual mode. 2. Press the > key twice, and press the [VOL+] key twice to display as follows. Display 3. Press the > key once to select the item number 0131 and display as follows. Display 4. Measure the ambient temperature. 5. Adjust with [VOL+]/[VOL--] keys so that the adjusted value (hexadecimal value) becomes the ambient temperature. (example: 25 °C = 19h) 6. Press the X key to write the adjusted value. 7. Press the x key four times and back to the Display Check mode. 3-4. Power Supply Voltage Adjustment Adjustment must be done with the following order. 3-4-1. Setting Procedure: 1. Enter the test mode (Display Check mode), and make sure that the power supply voltage is 1.2 V. 2. Press the [VOL+] key to enter the Manual mode. 3. Press the [VOL+] key twice to display as follows. Display 4. Press the > key once, press the [VOL+] key once, and press the > key once again to display as follows. Display 5. Repeat the next procedures (3-4-2. PwrAdj Adjustments), and adjust all contents of “table 3-4-1. PwrAdj Specifications”. 130 Temp 131 ###S** adjustment value (hexadecimal) 2 POWER 210 PwrAdj Ver 1.1

Repeat the following procedures and adjust all contents of “table 3- 4-1. PwrAdj Specifications”. Example Display (Item No. 2211) Procedure: 1. Connect the digital voltmeter to measuring point (refer to the following table) and ground (CL433). 2. Press the > key to change the item number. 3. Adjust with [VOL+]/[VOL--] keys so that the value of digital voltmeter becomes specification value. 4. Press the X key to write the adjusted value. 5. Press the > key to select the next item. 6. Repeat adjustment from step 1 until item number 2233. 211 AD ** adjustment value (hexadecimal) ItemNo. Display Specification value Measuring point 2211 211 AD ** 2.05 V + 0.02 V CL8027 2212 212 AD ** 2.25 V ± 0.01 V CL8027 2213 213 AD ** 1.20 V + 0.01 V CL8001 2214 214 AD ** 3.10 V ± 0.015 V CL658 2215 215 AD ** 3.10 V ± 0.015 V CL658 2216 216 AD ** 3.02 V ± 0.02 V CL919 2217 217 AD ** 3.02 V ± 0.02 V CL919 2218 218 AD ** 2.275 V ± 0.01 V CL921 2219 219 AD ** 2.480 V ± 0.01 V CL921 2221 221 AD ** 2.740 V ± 0.01 V CL921 2222 222 AD ** 2.985 V ± 0.01 V CL921 2223 223 AD ** 2.52 V ± 0.02 V CL931 2224 224 AD ** 0.89 V ± 0.02 V CL604 2225 225 AD ** 1.08 V ± 0.02 V CL604 2226 226 AD ** 1.52 V ± 0.02 V CL604 2227 227 AD ** 2.27 V ± 0.02 V CL604 2228 228 AD ** 2.97 V ± 0.02 V CL604 2229 229 AD ** 0.94 V ± 0.02 V CL604 2231 231 AD ** 1.28 V ± 0.02 V CL604 2232 232 AD ** 2.57 V ± 0.02 V CL604 2233 233 AD ** 2.57 V ± 0.02 V CL604 Note1: “**” is adjustment value (hexadecimal number). Note2: Ground point of all measuring points is CL433. Table 3-4-1. PwrAdj Specifications Adjustment Location: C427 R511 R868 R512 C533 C531 C527 C559 C822 R802 R806 R807 R801 C604 R678 R643 R353 R252 R254 R253 R358 R154 R153 R152 R258 R257 R158 R157 R251 C364 R355 R151 R354 C625 R652 R485 R480 C479 R483 R484 C429 C476 R472 R473 R471 C361 R474 R475 R612 R671 R628 R665 C642 R617 R629 C645 C638 R673 R435 C415 C406 C412 C407 C421 R446 R447 C673 R434 R425 R804 C853 R832 C830 R862 R861 R646 R681 C633 R805 C611 C408 R436 C671 R685 C677 R683 C602 C630 R654 R647 R679 R605 C620 R645 C675 R653 R670 R867 C856 C961 R860 R520 R524 R812 R817 C809 C857 R820 R869 C803 C574 C554 R505 C520 R443 R442 C434 C519 C517 C516 C521 C511 R639 C644 R675 R312 R315 W404 R618 R314 R601 R455 R456 R619 C322 C319 C324 C430 C314 R101 R201 R203 R301 C455 C461 R305 C325 R310 R309 C425 C636 R352 R356 R103 C306 C106 R106 R206 C206 C105 C104 R105 C308 R307 R107 R207 R205 C204 C205 C151 C152 C251 C252 R255 R262 R682 R684 R155 C478 CN471 R478 R359 C363 R609 R616 C641 R638 C515 C557 C522 C523 C513 R657 R642 FB501 R641 R640 R636 R441 R444 C528 C536 C550 C552 C538 R502 R501 C529 C525 C547 C526 C804 R815 R811 R823 C860 C555 C565 R843 C847 VDR801 R827 R810 R519 R518 R517 C566 R509 C545 C669 SL802 IC604 IC801 IC804 IC401 IC605 IC606 IC607 C668 C805 E C B Q504 C802 C801 C858 C859 R808 FB807 X802 C567 + L506 L504 L502 + C556 + C652 + C635 C666 C672 + C637 IC501 IC603 C530 C438 C524 C537 C539 R525 R526 C661 C660 R650 R635 C553 + C518 + L503 D611 Q615 Q901 Q614 K A Q613 G D S L907 L906 L901 FB801 C634 R648 C327 R308 C102 C328 R677 R664 L608 R649 C628 R845 C674 X801 Q802 Q609 Q401 S D G Q801 D803 A K + C622 C411 + C627 + C616 + C614 + C613 + L601 D602 K A D603 A K Q612 S D G SL901 L603 L701 L702 CN701 C423 + C424 + L605 C653 + C612 + C621 + C356 + C321 + C643 Q611 Q608 E C B Q607 D604 A K + C658 + C354 F351 F1 + C323 D609 D613 D610 A K A K IC601 D401 K A C607 C609 R608 C355 C351 C253 C153 C154 C254 C601 FB471 FB357 FB2 FB353 FB354 FB1 FB355 C619 D601 K A K A L303 IC302 D435 A K D303 D302 K A K A C315 + C313 + C316 + R306 R304 FB303 C456 C458 C459 C304 C460 C302 IC301 IC352 Q351 B C E IC602 D251 D471 Q471 K A K A Q618 D352 Q353 Q352 C202 FB201 E C B Q301 FB301 FB101 LF451 R454 C457 FB452 FB451 BP701 SL894 SL892 SL891 S892 (HALF LOCK) J402 1 7 21 15 14 8 22 28 1 1C 2B 2E 1 10 1E 1B 2C 3 5 4 2C 1B 1E D G D D D S D G D D D S D G D D D S K K 1C 1 4 5 3 1 6 18 13 12 19 24 7 2C 1B E 2B K K A 2E 2B 1C 1 16 1 3 4 2 1 1 3 5 5 8 4 1 1 2 4 3 4 2 4 3 E C B ∗ ∗ ∗ ∗ G D S SL801 1 4 8 5 1 1 3 5 4 3 5 4 2C 1B 1E 2E 2B 1C 4 3 1 2 57 56 54 52 49 45 41 37 34 32 30 29 58 59 55 53 50 46 42 38 35 33 31 28 84 87 89 91 94 98 102106 109 111 3 2 85 86 88 90 93 97 101105 108 110 112 1 62 63 64 51 47 43 39 36 25 24 65 66 67 68 48 44 40 23 22 21 77 78 79 96 100104 12 11 10 9 80 81 92 95 99 103107 8 7 6 69 70 71 72 20 19 18 17 73 74 75 76 16 15 14 13 60 61 27 26 82 83 5 4 5451 48 45 43 42 40 37 34 31 5552 49 47 44 41 38 36 33 30 5653 50 46 39 35 32 29 1 4 7 11 18 22 25 28 2 5 8 10 13 16 19 21 24 27 3 6 9 12 14 15 17 20 23 26 D441 A K IC902 1 2 4 3 2C 1B 1E 2E 2B 1C W403 IC402 DC IN 3V − + D801 A K DRY BATTERY SIZE "AA" (IEC DESIGNATION R6) 1PC. 1.5V – MAIN BOARD (Conductor Side) – CL935 CL931 CL8001 CL8055 CL8027 CL921 CL919 CL658 CL604 CL432 (BATT–) CL433 (GND) CL460 (VBUS GND) CL453 (VBUS 5V) CL431 (BATT+) Ver 1.1

Procedure: 1. In the “3-4-2. PwrAdj Adjustments” completed status, press the > key to display as follows. Display 2. Apply the voltage of 5 V to the CL453 (VBUS 5V) and CL460 (VBUS GND). 3. Press the > key to change the item number to 2241. 4. Adjust with [VOL+]/[VOL--] keys so that the value of digital voltmeter becomes specification value. (refer to “table 3-4-2. VBsAdj Specifications”) 5. Press the X key to write the adjusted value. 6. Press the > key to select the next item, and repeat adjustments to item number 2243 at the same manner as step 3 to step 5. Item No. Display Specification value Measuring point 2241 241 AD ** 1.13 V ± 0.01 V CL8001 2242 242 AD ** 2.05 V + 0.02 V CL8027 2243 243 AD ** 3.30 V ± 0.01 V CL8055 Note1: “**” is adjustment value (hexadecimal number). Note2: Ground point of all adjustment points is CL433. Note3: Refer to page 18 for adjustment location. Table 3-4-2. VBsAdj Specifications 7. Press the > key to select the item number 2244, and turn off the power supply of battery terminal. 8. Adjust with [VOL+]/[VOL--] keys so that the voltage of between CL935 and CL433 (GND) becomes 1.80 V (− 0.02 V). 9. Press the X key to write the adjusted value. 10. Apply the voltage of 1.2 V to the battery terminal again. 11. Press the x key to display “240 VBsAdj” (Item number: 2240). 12. Turn off the voltage of 5 V to the CL453 (VBUS 5V) and CL460 (VBUS GND). 13. Press the x key three times and back to the Display Check mode. 240 VBsAdj 3-5. Charge Function Check Note: When perform this check, don’t apply a voltage to battery terminals. Procedure: 1. Connect the digital voltmeter to CL431 (BATT+) and CL433 (GND). 2. Enter the test mode using the AC adapter. 3. Press the [VOL+] key to enter the Manual mode. 4. Press the [VOL+] key twice to display as follows. Display 5. Press the > key once, press the [VOL+] key once, press the > key once, press the [VOL+] key three times, and press the > key once to display as follows. Display 6. Adjust with [VOL+]/[VOL--] keys so that the value of digital voltmeter becomes 1.80 V. 7. Press the X key to write the adjusted value. 8. Press the > key to select the next item. 9. Disconnect the digital voltmeter. 10. Press the > key to select the next item (2262) and display “262 AD CC”. 11. Press the X key and confirm that the adjustment value changes from “CC” to “DD”. If it changes to “BB”, IC401 (for charge IC) is fault. 12. Press the > key to select the next item (2263) and display “263 AD CC”. 13. Press the X key and confirm that the adjustment value changes from “CC” to “DD”. If it changes to “BB”, IC401 (for charge IC) is fault. 14. Disconnect the power supply (AC adaptor). 15. Connect the resistor of the specified value (see table below) to the battery terminals (CL431: BATT+, CL432: BATT−), and then connect the AC adapter again, and enter the test mode. 16. Select item number 2264 through the operation similar to steps 2 to 8. 17. Press the X key and confirm that the adjustment value changes from “CC” to “DD”. If it changes to “BB”, IC401 (for charge IC) is fault. 18. In the same manner, exchange the resistors with the power supply disconnected, and confirm that the adjustment value is “CC” in each item number. Note: Be sure to disconnect the AC adapter when exchanging the resistors. Doing so with the power supply connected causes a trouble. Item No. Display Connecting Resistor 2262 262 AD ** No resistor 2263 263 AD ** No resistor 2264 264 AD ** 22 Ω (0.1 watts or more) 2265 265 AD ** 10 Ω (1.0 watts or more) 2266 266 AD ** 10 Ω (1.0 watts or more) 2267 267 AD ** 2.2 Ω (1.5 watts or more) Table 3-5-1. Charge Adjustment Specifications 2 POWER 261 AD ** adjustment value (hexadecimal) Ver 1.1

Item No. Parameter Result Decimal Hexadecimal 0211 Pr_nominal 2.50 mW 50 32h 0212 Kr −0.3 %/°C 30 1Eh 0213 Pw_nominal 7.35 mW 147 93h 0214 Kw −0.4 %/°C 40 28h 0215 Prmin 1.9 mW 38 26h 0216 Pwmin 5.8 mW 116 74h Procedure: 1. In the test mode (Display Check mode), press the [VOL+] key to enter the Manual mode. 2. Press the > key once, press the [VOL+] key once, and press the > key once again to display as follows. Display 3. Press the > key once to select the item number 0211. 4. Adjust with [VOL+]/[VOL--] keys so that the adjustment value of LCD becomes calculated value. 5. Press the X key to write the adjusted value. 6. Press the > key to next item. 7. Repeat adjustment from step 4 until item number 0216. 3-7-2. Other setting 1. In the test mode (Display Check mode), press the [VOL+] key to enter the Manual mode. 2. Press the > key five time to select the item number 0113 and display as follows. Display 3. Press the [VOL+]/[VOL--] key and set the according value to each model type and destination referring to the following table. 4. Press the X key to write the adjusted value. Destination Model Type MZ-NH700 MZ-NHF800 US − 50 Canadian, Australian 20 30 AEP, UK, East European A0 B0 E18, Hong Kong, Korean, 25 34 Chinese, Tourist E91, Mexican 20 − • Abbreviation E18: 100V - 240V AC area in E model E91: 220V AC area in E model Table 3-7-2. Mode Type and Destination Setting 210 DiscPr 113 ###S** adjustment value (hexadecimal) 3-6. Laser Power Check Procedure: 1. In the test mode (Display Check mode), press the [VOL+] key to enter the Manual mode. 2. Open the lid and press the . key continuously until the optical pick-up moves to the most inward track. 3. Set the laser power meter so that the laser beam from the optical pick-up aims at the objective lens of laser power meter at right angle. 4. Press the [VOL--] key once to display as follows. Display 5. Press the > key three times to select the item number 9111 and display as follows. Display 6. Confirm that the value of laser power meter is 0.67 mW ± 21%. 7. Press the > key to select the item number 9112. 8. Confirm that the value of laser power meter is 0.76 mW ± 18%. 9. Press the > key to select the item number 9113. 10. Confirm that the value of laser power meter is 6.25 mW ± 12%. 11. Press the x key four times and back to the Display Check mode. 3-7. Setting The Adjustment Values 3-7-1. Hi-MD3 setting Preparation: 1. Perform calculation every item based on the data given by the Hi-MD3 adjustment disc by referring to the following table. (Round off the value in decimal place) 2. Convert the calculated value into hexadecimal number. Note: The Hi-MD3 adjustment parameters vary depending on the disc, and therefore use the parameters of the disc used when performing the adjustment. Item No. Calculating formula (*3) 0211 Pr_nominal / 0.05 (*1) Por / 0.05 0212 Kr × (−100) 0213 Pw_nominal / 0.05 (*2) Ppw / 0.05 0214 Kw × (−100) 0215 Prmin / 0.05 0216 Pwmin / 0.05 *1) If the “Pr_nominal” value is indicated, use the “Pr_nominal” value and not used “Por” value. *2) If the “Pw_nominal” value is indicated, use the “Pw_nominal” value and not used “Ppw” value. *3) Round off after the decimal point. Table 3-7-1. Hi-MD3 adjustment parameter 9 DESIGN 111 ###S** Ver 1.1

Note1: Be sure to adjustment so that the set is horizontal and the LCD is upside. Unless performed in that state, it is not adjusted correctly. Note2: If NG is displayed in the middle of this adjustments, perform “3-2. Initialize The Adjustment Value” and “3-7. Setting The Adjustment Values” again, then retry this adjustments from step 1. Procedure: 1. Insert the full charged Ni-MH rechargeable battery (NH- 10WM), then open and close the lid and enter the test mode (Display Check mode). 2. Press the [VOL--] key to enter the Overall Adjustment mode. 3. Insert the CD adjustment disc (TDYS-1). 4. Put the main unit horizontal so that the LCD becomes upside, and press the . key. 5. Wait until “CD OK” is displayed on the LCD. 6. Insert the MD1/HiMD1 hybrid adjustment disc (MDW-74/GA1). 7. Put the main unit horizontal so that the LCD becomes upside, and press the > key. 8. Wait until “MD1 OK” is displayed on the LCD. 9. Insert the Hi-MD3 adjustment disc (HMD1GSDJ). 10. Put the main unit horizontal so that the LCD becomes upside, and press the [VOL+] key. 11. Wait until “HMD OK” is displayed on the LCD. 12. Eject the disc. 13. Put the main unit horizontal so that the LCD becomes upside, and press the [VOL--] key. 14. Wait until “OfstOK” is displayed on the LCD. 15. Press the x key and back to the Display Check mode. 3-9. Resume Clear Procedure: 1. In the test mode (Display Check mode), press the [VOL+] key to enter the Manual mode. 2. Press the [VOL+] key once, press the > key once, press the [VOL--] key once, press the > key once, and press the [VOL+] key twice, press the > key three times to select the item number 1933. 3. Press the X key to resume clear. 4. Press the x key four times and back to the Display Check mode. And remove the Ni-MH rechargeable battery. 3-10. Releasing The Test Mode Refer to the “SECTION 4. TEST MODE”. Note: Once the test mode is activated with this application, the test mode is then activated forcibly by only turning on the power. After the repair completed, be sure to release the test mode by using this application once more. Ver 1.1

8 48 47 40 41 42 23 9 35 21 32 33 7 56 1 54 55 50 51 52 49 15 14 18 19 IY VREF OPTICAL PICK-UP BLOCK (ABX-U) HR601 OVER WRITE HEAD D D_C PD_I PDO_SOURCE C B A VREF10 A_C JY JX IX IY RFO PEAK BOTM ABCD FE TE ADFG PD-NI VREF09 SBUS SCK S-MON XRESET RF AMP, FOCUS/TRACKING ERROR AMP IC501 M703 OVER WRITE HEAD UP/DOWN 17 IX JX JY A B C D S0 S1 L2 TRK+ FCS+ FCS– FCS+ FCS– TRK– TRK+ TRK– 101 106 107 108 109 114 153 110 225 113 252 209 210 251 142 77 84 82 60 62 169 170 164 165 166 160 232 168 167 172 216 157 156 154 155 20 19 29 30 162 163 28 48 49 50 64 1 3 54 53 52 55 238 26 46 27 25 63 62 22 23 24 21 182 IIN PD_BUF 20 F OVER WRITE HEAD DRIVE Q601, 602 M HB OUTA OUTB CLK EFM EFMO OVER WRITE HEAD DRIVE IC601 (1/2) RFI TO IC801 (2/3) (AUDIO SECTION) 145 VIN PEAK BOTM ABCD FE TE ADFG VC XRF_RST SE SSB_CLK PF1/S0DO PF2/S1DO SSB_DATA 38 45 OFTRK VC 123 180 VREF_MON OFTRK APCREF_DA SYSTEM CONTROLLER, DIGITAL SIGNAL PROCESSOR IC801 (1/3) A CLK SLCU SLCV SPCU SPCV SPCW SLD MON U SLD MON V CLV MON U CLV MON V CLV MON W SPRD SPDL_MON SLDW SLDV SRDR SLD_MON FRDR FFDR TRDR TFDR SPDV SPDW XRST_MTR_DRV RI1 FI1 RI2 FI2 WI2 VI2 UI2 VI1 WI1 CPWO2 CPVO2 CPUO2 SLD MON W SLD MON V SLD MON U STALL UI1 PWM1 FO2 FCS– FCS+ TRK– TRK+ COM2 WO1 CPVI2 WO2 CPUI2 CPWI2 CPUI1 CPVI1 CPWI1 COM1 FOCUS/TRACKING COIL DRIVE, SPINDLE/SLED MOTOR DRIVE IC701 M701 (SPINDLE) 11 RF_IY 10 RF_IX 26 CLK 174 FS256_OUT PLSE_XDC CONT 254 272 LDPEN XLSRCK 158 FS4 59 60 61 CPWO1 CPVO1 CPUO1 CLV MON W CLV MON V CLV MON U 159 51 SFDR PWM2 289 45 HI_Z_SLO ST2 290 4 HI_Z_SPDL ST1 63 175 EFM_CLK CHOPPERCLK 56 245 LATCH XCS_REC_DRV 69 HBB 78 HA 70 HAB U W V M702 (SLED) U W V 171 SLCW SLD MON W 161 SPFD NPPO 43 ADIP_IN 39 13 RF_JX 12 RF_JY RF BUFFER Q504 • SIGNAL PATH : PLAYBACK : REC L2 B+ L1 L1 B+ VCC REG3 B+ PVCC REG2 B+ MVCC MDVCC 32, 33 UO2 39, 40 UO1 9, 10 VO1 6, 7 VO2 42, 43 RO2 35, 36 FO1 16, 17 RO1 13, 14 (Page 23)

IC801 (2/3) XMUTE/MUTE 211 212 PF3/RTG3 199 BEEP 314 UDP 318 UPUEN 315 UDM 3 2 DATA+ DATA– 1 VBUS CN451 (USB) 320 UOSCO 319 UOSCI X801 48MHz 311 OSCO 239 XCS_NV 310 OSCI X802 22.5792MHz 195 SI0 196 SO0 197 SCK0 2 24 4 23 22 21 15 17 18 HEADPHONE AMP IC352 OUTA OUTB BEEP_OUTA BEEP_OUTB 7 SDT0 VREF_IN INA INB PW_SW MT_SW BEEP_IN 28 LIN 1 RIN 3 AVDD 19 PRER 18 PREL 13 SDO0 SCK0 F SDO0, SCK0 E VBUS B XRST2 C XWK1, XWK2, XWK4 J352 i 1 2 3 4 XCS SCK DI DO EEPROM IC892 • SIGNAL PATH : PLAYBACK : OPTICAL IN : LINE IN : USB input from PC : MIC IN : USB output to PC RVDD D RMC KEY RVDD DTCK KEY-R RGND VB VB F351 STAT 313 DTCK 131 RMC_KEY 134 RADIO_ON 147 AOUTL 148 AOUTR 173 DIN 200 XOPT_CTL 185 OPT_DET J301 186 XJACK_DET 307 ADDT 306 FS256 309 XBCK 308 LRCK 190 XPD_ADC 189 XCS_ADC REG1 B+ A/D CONVERTER, MIC AMP IC301 FROM IC801 (1/3) (MD SERVO SECTION) 187 XMIC_DET B+ SWITCH Q301 9 MCLK 8 BCLK 10 LRCK 14 PDN 11 CDTI 12 CCLK 13 CSN VC01 B+ LINE IN (OPT) J302 MIC (PLUG IN POWER) DDC3 B+ 133 REC_KEY/DOWNLOAD 248 JOG_A 249 JOG_B 227 XHOLD_SW 183 PAUSE_KEY 124 SET_KEY_1 125 SET_KEY_2 213 SI1 214 SO1 215 SCK1 236 XCS_LCD 192 XRST_LCD RESET SWITCH Q471 T_MARK JOG_A JOG_B HOLD PAUSE SET_KEY_1 SET_KEY_2 SDI SDO SCK CS LCD MODULE RST XWK DVDD XWK1 XWK4 DDC3 B+ REG VSTB B+ +2.4V REGULATOR IC471 253 S894–2 Hi-MD PROTECT DETECT HIMD_PROTECT 188 S893 OPEN/CLOSE DETECT OPEN_CLOSE_SW 184 S894–1 PROTECT DETECT PROTECT –1 –2 135 S892 HALF LOCK XWK2 HALF_LOCK_SW/ OPEN_SW VB B+ 193 USB_WAKE WAKE UP SWITCH Q803 128 WK_DET F1 6-2. BLOCK DIAGRAM – AUDIO Section – (Page 23) (Page 23) (Page 23) (Page 23) (Page 23)

246 SYSTEM CONTROLLER IC801 (3/3) GND_SW 226 219 73 256 257 207 VREC_SEL VBUS_VB_CTL 25 LG VCO1 11 7 LVB 27 VB 14 L1 13 L1 38 L2 37 L2 DW_2B DW_2T 55 REGI1 52 REGI2 48 REGI3 44 43 VRMC 6 DATA SDO0 SCK0 SLEEP 58 CLK 63 XWK3 3 64 STRB 59 SCK 60 XWK2 4 XWK4 2 VG 24 RVDD VC1 10 VO1 12 VC B+ VG B+ VC01 B+ VCO2 B+ VSTB B+ DDC3 B+ REGO2 51 REG2 B+ REGO1 54 REG1 B+ RVDD VREF 57 VSTB 9 VCO2 40 REGO3 47 RF1 26 CHG_SW1 30 VO 32 VI 6 IN1– 12 I_CTL1 20 BAT+ 31 CHARGE CONTROL IC401 4 7 29 23 VI_CTL CHG_CTL I_CTL2 I_CTL3 A/D TYPE2 22 16 REG3 B+ MDVCC VREC B+ 218 233 YUZU_SLEEP XCS_PWR_IC 181 RECP 231 RECP_MON XRST2 34 XRST1 17 229 XRST2_DET XRST2 POWER CONTROL IC601 (2/2) 83 VG 101 TSBV_IN 97 REG_IN 90 DVDD_IN 105 VSTB_IN 18 VREF_IN 112 VREC 4 VRECO_2 5 VRECO_1 10 UP_1B 9 UP_1T 81 VREC_IN 80 VREC_IN 6 L1_2 7 L1_1 46 POWFB SDO0 SCK0 SDO0 SCK0 F B CLK A XWK1, XWK2, XWK4 C REC KEY D 129 VBUS_MON VBUS B+ 127 HIDC_MON DC IN B+ 121 VB_MON VB B+ DRY BATTERY SIZE "AA" (IEC DESIGNATION R6) 1PC. 1.5V 299 PWM_L1 RESET SIGNAL GENERATOR IC902 +1.2V REGULATOR IC604 VOLTAGE DETECT IC606 RESET SWITCH Q618 VOLTAGE DETECT IC607 OR GATE IC605 WAKE UP SWITCH Q902 136 XRST 141 DACVREFH 5 XWK1 CHARGE ON/OFF CONTROL Q407 VBUS D401 B+ SWITCH Q901 B+ SWITCH Q901 B+ SWITCH Q352, 353 B+ SWITCH Q502, 503 REG4 B+ B+ SWITCH Q616, 617 87 64 94 59 58 RST_OUT VBUSSEL2 SLEEP_IN DATA SCK 54 VBUS 36 VPDRV 88 PVBUS 43 VBUSSEL 38 CLP 42 CLM 37 POWP1 41 POWP2 91 DVDD_OUT REG5 B+ +3.2V REGULATOR IC603 +2.1V REGULATOR IC882 DC/DC CONVERTER IC881 98 REG_OUT +1.2V REGULATOR IC602 REG5 OSC B+ REG F B+ 93 OSC_OUT +2.5V REGULATOR IC804 USB IF VDD 108 V33RO 13 VC VC B+ D609 D610 61 VIF 14 VC 67 RECP 250 VBUS_DET 51 VBUS_DET 316 USBHOLD 86 HOLD_OUT 317 SUSPEND 99 SUS_IN 132 RST_CONT 95 RST_IN REG5 VSTB B+ 106 VSTB_OUT REG5 TSBV B+ 102 TSBV_OUT D611 22 V3O_2 DDC3 B+ L1 B+ L2 B+ 21 V3O_1 28 V3FB 66 VG2 73 VG3 B+ SWITCH Q609 2 DW_1B 17 UP_3B 3 DW_1T B+ SWITCH Q603 25 L3_2 24 L3_1 B+ SWITCH Q614, 615 B+ SWITCH CONTROL Q613 205 B+ SWITCH Q611 B+ SWITCH Q801, 802 SWITCHING Q612 B+ SWITCH Q608 DC IN DETECT Q607 REGULATOR Q401 DC IN DETECT Q433 COMPARATOR IC402 GROUND LINE SWITCHING Q403, 406 CHARGE CONTROL Q432 300 PWM_L2 Q501 E VOLTAGE LIMITER Q451, 452 VOLTAGE DETECT Q884 REGULATOR CONTROL Q881 REGULATOR CONTROL Q883 204 MDVCC_CTL +3V REGULATOR IC502 POWER CONTROL IC901 D882 D883 D884 D885 BATT_MINUS_MON 130 237 240 221 222 CC_CTL/VI_CTL CHG_PWM CHG_I_CTL2 CHG_I_CTL3 CHG_MON 122 CHG_TYPE2 255 CN451 (2/2) (USB) THP401 DC IN B+ VB B+ VB B+ FCRAM_VDD FFCLR DRAM_ HOLD_DET DRAM_ VDD_CLR DRAM_ALONE FFCLR FCRAM_VDD DRAM_HOLD_DET DRAM_VDD_CLR DRAM_ALONE FFCLR FCRAM_VDD DRAM_HOLD_DET DRAM_VDD_CLR DRAM_ALONE REG5 B+ J402 DC IN 3V – + + (Page 22) (Page 22) (Page 22) (Page 21)

• MAIN board is multi-layer printed board. However, the patterns of intermediate-layer have not been in- cluded in this diagrams. • Lead Layouts Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • f : internal component. • C : panel designation. • A : B+ Line. • Total current is measured with MD installed. • Power voltage is dc 1.5 V and fed with regulated dc power supply from battery terminal. • Voltages and waveforms are dc with respect to ground in playback mode. no mark : PLAYBACK ∗ : Impossible to measure • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal produc- tion tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal produc- tion tolerances. • Circled numbers refer to waveforms. • Signal path. E : PLAYBACK j : REC J : OPTICAL IN F : LINE IN d : USB input from PC G : USB output to PC N : MIC IN • Abbreviation EE : East European model Note on Printed Wiring Board: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: Parts on the pattern face side seen from (Conductor Side) the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Component Side) the parts face are indicated. surface Lead layout of conventional IC CSP (chip size package) • Waveforms 500 mV/DIV, 500 ns/DIV 1 IC501 ra (FE) (MD Play Mode) 2 IC501 rs (TE) (MD Play Mode) 3 IC801

• See page 36 for IC Block Diagram. R712 C713 C715 C717 C716 C714 R706 R707 R708 C701 C702 C703 R709 R710 R711 C705 C706 C707 C708 C710 C709 L701 L702 IC701 BP701 C712 R713 CN701 0 0.1 0.1 0.1 0.1 0.1 2.2k 2.2k 2.2k 0.047 0.047 0.047 10k 10k 10k 0.01 0.022 0.01 0.022 0.022 0.01 0 0 BD6607KN 0.1 1k 10P A1 A2 A3 A4 A5 B1 B2 B3 XRST_MTR_DRV SLD_CON_W SLD_CON_V SLD_CON_U SLD_PWM SLD_MON_U SLD_MON_V SLD_MON_W CLV_CON_W CLV_CON_V CLV_CON_U CLV_PWM CLV_MON_U CLV_MON_V CLV_MON_W TF1 TR1 ZI2 ZI1 FR1 FF1 TRK+ TRK- FCS- FCS+ XRST_MTR_DRV SLD_MON_W SLD_MON_V SLD_MON_U SLD_PWM SLD_CON_U SLD_CON_V SLD_CON_W XRST_MTR_DRV SLD_CON_W SLD_CON_V SLD_CON_U SLD_PWM SLD_MON_U SLD_MON_V SLD_MON_W CLV_CON_U CLV_CON_V CLV_PWM CLV_MON_U CLV_MON_V CLV_MON_W CLV_CON_W CLV_CON_W CLV_CON_V CLV_CON_U CLV_PWM CLV_MON_U CLV_MON_V CLV_MON_W FF1 TF1 TR1 FR1 FF1 FR1 TF1 TR1 ZI1 ZI2 ZI1 ZI2 HD_DRV- HD_DRV+ CLVW CLVV CLVU CLVN SLEDN SLEDU SLEDV SLEDW VI2 UI2 PWM2 CPUO2 CPVO2 CPWO2 STALL GND VCC VG CPWO1 CPVO1 CPUO1 PWM1 UI1 VI1 WI1 PGNDW1 WO1 ST1 VMVW1 VO1 VO1 PGNDUV1 UO1 UO1 VMU1 VMR1 RO1 RO1 PGND1 FO1 FO1 VMF1 FI1 RI1 COM1 CPUI1 CPVI1 CPWI1 CPWI2 CPVI2 CPUI2 COM2 RI2 FI2 VMF2 FO2 FO2 PGND2 RO2 RO2 VMR2 VMU2 UO2 UO2 PGNDUV2 VO2 VO2 VMVW2 ST2 WO2 PGNDW2 WI2 FOCUS/TRACKING COIL DRIVE, SPINDLE/SLED MOTOR DRIVE V U N W V U N W (SPINDLE) OVER WRITE HEAD UP/DOWN (SLED) M702 M701 M703 (1/9) (Page 32 (Page 26) (Page 27)

• See page 36 for IC Block Diagrams. Q611 Q615 W601 W602 IC606 C668 C669 R663 R662 R660 R661 C601 R652 C619 C602 C604 C613 R654 C614 C675 R653 C616 C607 C609 C611 R624 R625 C648 D606 D615 D616 L606 C622 C628 L601 C633 C634 C635 D602 Q612 C637 C653 R671 C645 C638 R629 C642 C641 R616 L608 R664 C672 C666 R675 R665 R649 R648 L607 R646 R681 R619 R601 IC601 C636 C630 R659 C671 R635 R673 R650 Q613 D611 C661 Q614 R642 C660 R636 R668 R657 R640 R641 R679 R638 R639 R612 R670 L603 D603 C649 C652 C650 C676 C673 R628 D609 C612 Q616 C621 C643 D610 IC605 IC602 R643 R618 R609 D604 C658 R677 R617 L605 R680 C627 R605 C620 D613 D614 Q608 IC603 Q609 Q603 C625 IC604 Q617 Q602 Q601 R608 Q607 R645 IC607 C677 D601 Q618 R683 R682 R685 R684 R647 C644 C646 D608 D605 D607 C674 R620 R622 R623 R621 R678 CL604 CL658 SI1410EDH-T1 SI1410EDH-T1 XC61CN1702NR 1 1 220k 470k 470k 470k 1 0 1 0.1 0.1 22 6.3V 1M 22 6.3V 0.01 22k 22 10V 1 1 0.01 470k 470k 0.047 MA22D17 MA22D17 MA22D17 47 6.3V 1 0.01 1 47 6.3V MA2Z748001S0 SSM3K01F(TE85L) 10 6.3V 10 6.3V 0 0.01 2200p 2.2M 0.047 0.01 1k 2.2 4.7 4.7 2.2M 0 1 1 47k 1M 100k 220k SC901585VAR2 0.1 0.1 100k 0.1 0 0 4.7 2SK1830-TE85L MA2Z748001S0 2.2 XP4601-TXE 100k 0.1 470k 0 0 220k 1M 220 220k 1M 2.2M 0 MA2Z748001S0 0.1 10 6.3V 10 6.3V 1000p 0.1 22 MA2Z748001S0 22 6.3V SI1410EDH-T1 10 4V 2.2 MA2Z748001S0 TC7S32LFU(TE85R) R1160N121B-TR-F 0 100k 100k MA22D2800LS0 47 6.3V 0 1k 0 47 6.3V 1k 0.047 MA2SD32008S0 MA2SD32008S0 XP4314-TX XC6209B322MR NTHD4508NTIG TS8K1TB 0.1 R1180Q121C-TR-FA XP4601-TXE MCH6617-TL-E CPH5614-TL-E 1 2SC4738F- Y/GR(TPL3) 470k XC61CN8902NR 0.1 MA2SD32008S0 XP4601-TXE 1M 1M 10k 10k 1M 4700p 0.047 MA2SD30 MA2SD30 MA22D17 33p 2.2 2.2 2.2 2.2 0 A1 A2 A3 A4 A5 C1 C2 C3 E1 E2 E3 E4 E5 E6 E7 E8 E9 E10 E11 E13 F1 D1 D2 F2 VB RMC_DTCK VBUS_VB_CTL XCS_REC_DRV VBUS_DET DDC3 REG_F EFM_CLK EFM RECP SUSPEND USB_HOLD 3.3V 4FS SDO0 SCK0 RST_CONT SLEEP VREC_SEL XRST REG5_REG REG5_VSTB REG5_OSC REG4_DVDD REG_DACVREFH TERRA_V RADIO_ON VREC_SEL XCS_REC_DRV XCS_REC_DRV VBUS_DET VBUS_DET REG_F REG_F EFM_CLK EFM_CLK EFM EFM RECP RECP SUSPEND SUSPEND USB_HOLD USB_HOLD 3.3V 3.3V 4FS 4FS SDO0 SDO0 SCK0 SCK0 RST_CONT RST_CONT SLEEP VREC_SEL XRST XRST REG5_REG REG5_REG HBB HAB HA HB REG5_VSTB REG5_VSTB REG5_OSC REG5_OSC REG4_DVDD REG4_DVDD HB HA HBB HAB REG5_VSTB REG_DACVREFH REG_DACVREFH RMC_DTCK SLEEP RADIO_ON S S D2 D2 D1 D1 G2 G1 S1 S2 S NC VSS VIN VOUT NC VOUT VDD GND VOUT ECO VDD GND CE S S NC_AI2 HOLD_OUT RST_OUT CRST DVDD_IN DVDD_OUT HOLDC OSC_OUT SLEEP_IN RST_IN PGND2 REG_IN REG_OUT SUS_IN PGND2 TSBV_IN TSBV_OUT VD33R PGND1 VSTB_IN VSTB_OUT BATSEL V33RO RF1 DTC1 VREC NC_A1 DW_1B VRECQ_2 VRECQ_1 L1_2 L1_1 INP1 GND PGND1 VC VC PGND3 PGND1 VREFIN PGND3 PGND3 V30_1 V30_2 33USEL L3_1 L3_2 V3FB OUTA VG OUTB VRECIN VRECIN PGND2 HA HB PGND4 CL VCP VG2 GND CH HAB HBB GND RECP PGND4 VBUSSEL2 EFM_CLK EFM VIF CLK DATA SCK NC_M12 LATCH XWKO VBUS WAKEC V33UO VBUS_DET VBUSREF L5_2 PGND5 VBUSSEL CLM POWP2 INP3 INP2 CLP POWP1 RF2 DTC2 INM2 INM3 DTC3 NC_M1 RF3 L5_1 POWFB PGND5 PGND5 CE GND VDD VOUT NC S S VG3 PVBUS INM1 DW_1T UP_1T UP_1B UP_3B DW_3T DW_3B VPDRV B+ SWITCH -1 -2 B+ SWITCH B+ SWITCH Q614,615 -1 -2 SWITCHING B+ SWITCH CONTROL +3.2V REGULATOR B+ SWITCH B+ SWITCH OVER WRITE HEAD DRIVE,POWER CONTROL * CSP(Chip Size Package) +1.2V REGULATOR +1.2V REGULATOR -1 -2 B+ SWITCH Q616,617 VOLTAGE DETECT OR GATE GND VCC -2 -1 -2 -1 S S S Q601,602 OVER WRITE HEAD DRIVE HR601 OVER WRITE HEAD (2/9) DETECT DC IN -1 -2 VOLTAGE DETECT RESET SWITCH NC VOUT VSS VIN 47µH 47µH 22µH 10µH 10µH (Page 32) (Page 27) (Page 31) (Page 30) (Page 29) (Page 28) (Page 25)

• See page 36 for IC Block Diagram. • See page 24 for Waveforms. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 so critiques pour la sécurité. Ne les remplacer qu par une pièce portant le numéro spécifié. R561 L504 L502 C529 C518 C520 C527 L503 R504 R503 R507 R508 C569 C568 R521 R522 FB501 C570 C573 C513 C521 C522 C525 C519 C556 C557 C531 C533 C538 C545 C547 C550 C552 C536 C537 C539 C553 C554 R525 R526 FB503 Q502 C558 R513 Q503 R514 R515 R516 C560 C564 C559 R512 R517 R518 R509 C565 R519 C555 R511 R524 R520 C526 C566 C567 C562 R501 R502 C517 C516 C515 C511 L505 CN501 C530 C524 C523 L501 FB502 Q504 Q501 IC501 L506 L507 IC502 C528 R505 C561 220k 0.1 4.7 6.3V 0.1 0.1 100k 100k 2.2k 2.2k 0.01 0.01 0 0 4.7 10V 1000p 0.01 10p 10p 4700p 0.1 4.7 6.3V 0.1 0.01 0.01 1000p 0.1 0.047 0.047 0.01 0.022 1 1 4.7 6.3V 0.1 0 0 0 2SA2018TL 1000p 10k 2SC4738F-Y/GR (TPL3) 47k 10k 47k 0.1 4.7 6.3V 4700p 0 10k 47k 0 0.1 1k 4700p 0 220 470 100p 0.1 4.7 6.3V 1 2.2k 1k 0.1 0.1 0.1 0.1 26P 1 0.01 0.1 0 0 2SC4627J-C (TX).SO MCH6604 SN761059ZQLR R1180Q301B 0.1 10 1 B1 B2 B3 C1 C2 C3 I1 I2 REG03 LC_DRV1 LC_DRV2 PEAK PLSE_XDC XLDON BOTM OFTRK MDVCC_CTL RFI VIN ADIP VC S_MON APCREF_DA SSB_DATA SSB_CLK XRST_RF VREF ABCD FE TE A_FS256 S1 S0 LC_DRV1 LC_DRV2 LC_DRV1 LC_DRV2 PEAK PEAK PLSE_XDC PLSE_XDC XLDON XLDON BOTM BOTM OFTRK OFTRK MDVCC_CTL MDVCC_CTL RFI RFI VIN VIN VC ADIP ADIP VC S_MON S_MON APCREF_DA APCREF_DA TE FE ABCD VREF XRST_RF SSB_DATA SSB_CLK SSB_DATA SSB_CLK XRST_RF VREF ABCD TE FE TRK- TRK+ FCS+ FCS- A_FS256 A_FS256 S0 S0 S1 S1 DVCC CP CPOUT SCK SBUS VGIN XRESET DGND CIG VC ADIP_IN ABCD FE TE NPPO AVCC2 TON_C BOTM PEAK D A B C AVCC JX JY IY IX PS EQ AGND OFC_C1 OFC_C2 VREF10 RFO VREF09 RF_IX RF_IY RF_JY RF_JX A_C PDO_SINK PDO_SOURCE PD_I PD_NI PD_BUF SMON VPP_LPF ADFG CCSL2 CLK CPGND CN TRK+ FCS- FCS+ TRK- L1 L2 CONT PLSE_XDC PVCC IIN LDK MDVCC GND F VREF VCC JY JX IY IX A B C D GND VOUT VDD CE S0 OFTRK CDN D_C RF BUFFER Q502,503 B+ SWITCH -1 -2 S S SWITCHING +3V REGULATOR FOCUS/TRACKING ERROR AMP RF AMP, CSP(Chip Size Package) * (3/9) S1 10µH 10µH 10µH 10µH 10µH 10µH (Page 29) (Page 32) (Page 26) (Page 25)

• See page 36 for IC Block Diagram. Q451 Q403 C574 C457 C430 FB451 FB452 C424 R455 R456 R421 C425 C427 Q452 R462 D458 R467 C453 C402 C403 LF451 D440 CN451 C429 C459 C458 C456 D457 R466 R464 R463 R425 R436 THP401 LF401 C426 C419 R418 R419 R420 C420 Q401 C406 C407 C408 R435 C411 C412 C421 R434 IC401 C452 W404 W403 D439 J402 D401 Q406 R437 R438 Q433 Q407 C415 D436 C416 C460 C461 D435 D441 C438 R444 C434 R443 R442 R441 R446 IC402 R447 R422 R423 R424 R433 Q432 R432 CL431 CL432 C423 CL453 C455 R454 CL460 CL433 RTQ035P02TR SI1410EDH-T1 0.1 0.1 1000p 220 5V 1M 470k 100k 0.1 0.1 XP4601-TXE 220k MA8056-L-TX 10k 0.047 220 5V 220 5V MA22D2800SL0 7P 0.1 0.1 0.1 2200p MA22D2800SL0 2.2M 100k 220 2.2k 220k 22 16V 0.1 100k 10k 4.7k 0.1 FZT968TA 0.1 0.1 0.1 0 22 16V 0.1 0.1 1M MM1655NCBE 0.1 MA22D2800LS0 MA22D2800LS0 XP4601-TXE 220k 100k 2SC4738FY/GR (TLP3) UN9214J-(TX).SO 0.1 MAZS068008SO 0.1 0.1 0.1 MAZS068008SO MAZS068008SO 0.1 100k 0.1 100k 100k 100k 0 NJU7008F3 0 1M 220k 470k 0.47 FZT688B-TP 1 (BATT+) (BATT-) 220 5V (VBUS 5V) 2200p 0 (VBUS GND) (GND) D1 G1 G2 G3 H1 D2 M1 M2 UDP UDM GND_SW VBUS_MON MINUS_MON TERRA_V CHG_MON CHG_I_CTL2 CHG_I_CTL3 CHG_PWM HIDC_MON CHG_TYPE2 UDM UDP CHG_PWM CHG_I_CTL2 CHG_I_CTL3 CHG_MON CHG_TYPE2 CHG_PWM UDP UDM HIDC_MON HIDC_MON CHG_TYPE2 CHG_I_CTL3 CHG_I_CTL2 CHG_MON S VBUS DATA- DATA+ IO GND SW_A SW_B S -1 -2 Q403,406 GROUND LINE SWITCHING Q451,452 DRY BATTERY SIZE"AA" (IEC DESIGNATION R6) 1PC. 1.5V (USB) -2 -1 BAT- RF1 IAMP_CAL AMP_SEL I_CTL2 CHG_SW1 BAT+ V0 VI2 VG PWT VI_CTL CHG_SW2 VI CHG_CTL PWR_WAKE RS I_CTL3 A/D GND I_SEL AD_SEL PGND I_CTL1 TYPE2 CFB IAMP_CTL A7CAL_SW IN1- TYPE1 WDT LED_CTL (4/9) DC IN 3V DC IN DETECT CHARGE ON/OFF CONTROL CHARGE CONTROL VOLTAGE LIMITER REGULATOR COMPARATOR CHARGE CONTROL (Page 32) (Page 26) (Page 32) (Page 29) (Page 33) (Page 30)

• See page 36 for IC Block Diagram. C959 C901 R924 C958 IC901 C924 D905 L907 C920 L904 C916 C908 R904 C919 R907 D902 C906 C909 R903 R906 C918 C903 C902 R912 D904 C915 L903 C922 C923 C926 R914 C928 C954 R917 R918 R920 R954 R955 R959 R960 R931 SL901 C931 C932 R951 R952 R953 R933 R934 R922 C929 C935 C936 R935 R936 C937 R937 R938 C927 L906 L901 D906 R958 C960 Q902 Q901 L9001 R925 C940 C948 C933 C939 IC902 C961 R908 R910 R927 R930 R926 R929 R964 CL935 CL921 CL919 CL931 0.1 0.1 470k 1 SC901584EPR2 47 6.3V MA2Z748001S0 0.1 10 6.3V 0.01 1M 0.022 10k MA2Z748001S0 1 22 16V 1M 47k 0.047 0.01 0.1 220k MA2Z748001S0 10 6.3V 100 6.3V 47 6.3V 1000p 10k 100p 1000p 220k 470k 470k 470k 2.2k 470k 0 0 2.2 0.01 0 0 4.7 220k 22k 100k 1000p 2.2 2.2 100k 47k 2.2 22k 47k 100p MA22D2800LS0 47k 0.1 XP4601-TXE TS8K1TB 47k 22 6.3V 22 6.3V 2.2 22 6.3V XC61CC1702NR 0.1 22k 22k 1k 47k 100k 100k 100k E1 E2 E3 E4 E5 E6 E7 E8 E9 E10 E11 E13 G1 G2 G3 I1 I2 J1 J2 J3 J4 J5 L1 L2 SDO0 SCK0 4FS XCS_PWR_IC XRST2 WK_DET RMC_KEY REC_KEY HALF_LOCK SLEEP CLK SEQSEL SCK STRB DATA VREF GND REGI1 REGO1 REGC1 REGI2 REGO2 REG2G REGC2 FFCLR XWK4 XWK3 XWK2 XWK1 VRMC LVB HVB VSTB VC1 VCO1 VO1 L1 L1 PGND1 PGND1 CRST2 XRST2 PGND2 PGND2 L2 L2 VO2 VCO2 VCIN VC2 DW_2T MUTEON REGC3 REGO3 REGI3 XRST1 CRST1 RF1 INM1 CTL VG LG PGND3 VB VGSEL2 VGSEL1 INM2 RF2 DTC2 S S NC VSS VIN VOUT XRST1ADJ DTC1 DW_2B RESET SIGNAL GENERATOR POWER CONTROL -1 -2 SWITCH WAKE UP B+ SWITCH WDT (5/9) 10µH 47µH 100µH 10µH 47µH 10µH (Page 28) (Page 27) (Page 33) (Page 30) (Page 26)

• See page 36 for IC Block Diagram. Q353 IC352 C151 C152 C251 C252 R153 R154 R253 R254 R257 R258 R157 R158 R351 C353 C154 R155 C254 R255 C160 C260 R156 R256 C355 C356 C351 C354 R353 R354 R356 R358 R355 FB355 FB353 FB357 R352 C352 L351 D352 D151 D251 F351 J352 Q351 C361 C364 Q352 R261 R161 R160 R260 FB2 FB354 FB1 F1 R359 R162 R262 C363 C253 C153 R251 R151 R252 R152 SI1410EDH-T1 TA2131FLG(EL) 4700p 2200p 4700p 2200p 10k 10k 10k 10k 1k 2.2k 1k 2.2k 47 0.1 0.22 10 0.22 10 220 4V 220 4V 4.7k 4.7k 2.2 10 4V 1 4.7 4V 22k 10k 100k 2.2M 1M 220k 10 6.3V 0 NNCD6.8H-T1 02DZ2.4-Z(TPH3) 02DZ2.4-Z(TPH3) 0.25A 125V 2SC4738F-Y/GR (TPL3) 0.01 0.1 XP4314-TX 22 22 1.5A 63V 0 0 0 0.1 F1 H1 J1 J2 J3 J4 J5 F2 S_GND XHP_STBY BEEP MUTE AOUTR AOUTL RMC_KEY XCS_PWR_IC WK_DET REC_KEY HALF_LOCK XRST2 GND BEEP MUTE XHP_STBY AOUTR AOUTL BEEP MUTE XHP_STBY AOUTR AOUTL RMC_KEY RMC_KEY XCS_PWR_IC WK_DET REC_KEY HALF_LOCK XRST2 RMC_DTCK RADIO_ON * * * * * * * * S VCC2 OUTA PWR_GND OUTB DET AGC_IN BST_OUT BST_NF2 LPF2 BST_NF1 LPF1 VREF VREF_IN GND BEEP_IN BST_SW MT_SW PW_SW MT_TC VCC1 INB INA BEEP_OUTB OUTA BEEP_ RVDD VB DTCK STAT RGND KEY_R (6/8) B+ SWITCH -1 -2 Q352,353 HEADPHONE AMP REFERENCE VOLTAGE SWITCH * R160,260 0 10 (AEP,UK,EE) (EXCEPT AEP,UK,EE) (AEP,UK,EE) * * * C153,253 R152,252 R151,251 1 2.2 4.7k 2.2k 4.7k 10k (US) (EXCEPT US) (US) (EXCEPT US) (US) (EXCEPT US) (Page 29) (Page 28) (Page 31) (Page 32) (Page 26)

• See page 36 for IC Block Diagram. R476 R477 R471 R472 R473 R475 R490 R491 R894 S894 C481 C479 R485 FB471 R474 C892 R486 C480 R895 R897 R480 R483 R484 CN471 IC471 SL892 SL894 SL891 IC892 D471 C476 C478 Q471 S893 S892 R478 R489 C860 C858 D473 4.7k 4.7k 0 0 0 0 100 100 100k 1 0.1 470k 0 1k 0.1 0 2.2 100k 0 100k 470k 220k 16P XC6219B242MR HN58X2564FPI MA2Z748001S0 1000p 0.01 XP1501-TXE 4.7k 100 0.1 0.1 MAZS068008SO K1 K2 K3 K4 K5 K6 VB RMC_DTCK RMC_KEY DDC3 REG_F 3.3V 4FS SDO0 SCK0 SLEEP RST_CONT VREC_SEL XRST REG5_REG REG5_VSTB REG5_OSC REG4_DVDD XCS_PWR_IC WK_DET REC_KEY HALF_LOCK XRST2 S_GND GND REG_DACVREFM RADIO_ON REG5_REG REG5_VSTB SDI0 XCS_NV SDO0 SCK0 WK_DET REC_KEY HALF_LOCK XRST2 RMC_KEY XCS_PWR_IC XCS_LCD SDI1 SDO1 SCK1 LCD_RST JOG_B JOG_A SET_KEY_2 SET_KEY_1 REC_KEY WK_DET XHOLD_SW PAUSE XRST2 RMC_DTCK 4FS SDO0 SCK0 RST_CONT SLEEP VREC_SEL XRST REG_F REG5_REG 3.3V REG5_VSTB REG5_OSC REG4_DVDD HIMD_PROTECT PROTECT HALF_LOCK OPEN_CLOSE_SW REG5_REG REG_DACVREFM RADIO_ON XCS SO XWP GND VCC XHOLD SCK SI DVDD JOG_B JOG_A SET_KEY_2 SET_KEY_1 T_MARK CS SDI SDO SCK RST XWK HOLD PAUSE DGND SGND VOUT CE VSS VIN NC +2.4V REGULATOR RESET SWITCH -2 -1 -2 -1 PROTECT DETECT Hi-MD PROTECT DETECT S894-1 S894-2 (HALF LOCK) (OPEN/CLOSE DETECT) EEPROM (NOT SUPPLIED) LCD MODULE (7/9) (Page 30) (Page 26) (Page 32

• See page 40 for IC Pin Function Description. • See page 24 for Waveforms. R825 C803 R857 C810 C817 C814 C812 C832 C833 R840 C857 R820 C809 R817 R812 C804 C805 R821 R818 R819 C828 R869 IC804 R845 Q802 C822 C823 C853 C818 C820 C819 FB801 X801 R802 C811 C839 C835 FB807 R809 R863 R864 FB802 FB809 FB810 R855 R856 R860 R843 C847 R842 R876 R832 R822 R862 C856 R867 C821 R823 SL802 R806 R801 C843 R839 R804 R805 C801 C802 R868 C859 R841 R808 X802 R807 Q803 R866 C808 R815 R811 Q801 C850 L803 L804 C816 C846 C845 L801 R824 L805 D801 R833 R858 C827 SL801 D803 R829 C861 R837 IC801 R879 R878 R880 R813 R826 C836 C838 C864 R861 R827 FB803 VDR801 C830 R865 L802 R830 R810 CL8001 CL8027 CL8055 0 0.01 470k 0.1 0.1 0.1 1 1 1 0 22p 220 0.1 1k 100k 0.01 0.47 2.2M 2.2k 1k 1000p 0 XC61CC2502NR 0 XP152A12C0MR 0.1 0.1 0.1 10 6.3V 0.1 47 6.3V 0 48MHz 0 0.1 0.1 0.1 0 0 0 220 0 0 0 0 10 2.2k 0.1 47k 0 10k 1M 1M 0.1 1M 0.1 10k 4.7k 4.7k 0.1 0 22 22 7p 7p 0 0.1 10 4.7k 22.5792MHz 2.2k 2SC4738F-Y/GR (TPL3) 0 1 220k 10k 2SK1830-TE85L 0.1 10 10 47 6.3V 0.1 47 6.3V 0 0 MA2Z748001S0 0 47k 0.1 MA2SD32008S0 0 0.1 2.2k CXD2681-223GG 47 47 47 220 0 10 6.3V 10 6.3V 0.1 22 100 1000p 470k 0 0 K1 K2 K3 K4 K5 K6 AOUTL AOUTR XHP_STBY MUTE BEEP VBUS_VB_CTL UDP UDM XCS_REC_DRV VBUS_DET EFM_CLK EFM RECP SUSPEND USB_HOLD GND_SW VBUS_MON LC_DRV1 LC_DRV2 PLSE_XDC XLDON PEAK BOTM OFTRK TE FE ABCD VREF XRST_RF SSB_DATA SSB_CLK ADIP S_MON APCREF_DA VC RFI MDVCC_CTL VIN XRST_MTR_DRV SLD_MON_W SLD_MON_V SLD_MON_U SLD_PWM SLD_CON_U SLD_CON_V SLD_CON_W CLV_MON_W CLV_MON_V CLV_MON_U CLV_PWM CLV_CON_U CLV_CON_V CLV_CON_W TF1 TR1 ZI2 ZI1 FR1 FF1 MINUS_MON A_FS256 REGO3 CHG_MON CHG_I_CTL2 CHG_I_CTL3 CHG_PWM HIDC_MON CHG_TYPE2 SDO0 SCK0 XCS_ADC XBCK LRCK FS256 ADDT XOPT_CTL DIN1 XJACK_DET OPT_DET XPD_ADC GND S0 S1 VB FCRAMVDD REG5_REG FCRAMVDD XMIC_DET BEEP MUTE XHP_STBY AOUTR AOUTL VBUS_MON VBUS_VB_CTL GND_SW AOUTR AOUTL VIN APCREF_DA EFM_CLK FF1 TF1 TR1 FR1 4FS SLD_PWM CLV_CON_U ADIP XRST HALF_LOCK REC_KEY RST_CONT RMC_KEY WK_DET REG5_VSTB SET_KEY_1 SET_KEY_2 VREF REG5_VSTB TE S_MON VC FE ABCD BOTM PEAK RFI XCS_REG_DRV VBUS_DET SSB_DATA SSB_CLK PLSE_XDC XCS_NV XCS_LCD XCS_PWR_IC CLV_CON_U XRST2 XHOLD_SW VREC_SEL XRST_RF SLEEP SLD_CON_U SDI1 MUTE XHP_STBY MDVCC_CTL BEEP SCK0 SDO0 SDI0 REG5_REG WK_DET LCD_RST POEN_CLOSE_SW PROTECT PAUSE EFM OFTRK SLD_CON_U SLD_CON_W SLD_CON_V SLD_MON_V SLD_MON_W CLV_MON_W CLV_MON_V CLV_MON_U CLV_CON_W CLV_CON_V CLV_PWM SLD_MON_U MINUS_MON A_FS256 LC_DRV1 LC_DRV2 EFM_CLK EFM RECP SUSPEND USB_HOLD VBUS_DET XCS_REC_DRV XRST_MTR_DRV SLD_CON_W SLD_CON_V SLD_CON_U SLD_PWM SLD_MON_U SLD_MON_V SLD_MON_W TF1 TR1 ZI2 ZI1 FR1 FF1 CLV_CON_W CLV_CON_V CLV_CON_U CLV_PWM CLV_MON_U CLV_MON_V CLV_MON_W USB_HOLD SUSPEND XLDON PLSE_XDC LC_DRV1 LC_DRV2 PEAK BOTM OFTRK TE FE ABCD VREF XRST_RF SSB_DATA SSB_CLK ADIP S_MON APCREF_DA VC RFI MDVCC_CTL A_FS256 VIN REG4_DVDD 3.3V REG_F REG5_VSTB REG5_OSC REG5_REG REG5_REG JOG_A JOG_B HIMD_PROTECT ZI2 ZI1 REG_DACVREFM XLDON VBUS_VB_CTL GND_SW VBUS_MON MINUS_MON XRST_MTR_DRV RECP SCK1 SDO1 CHG_MON CHG_MON CHG_I_CTL2 CHG_I_CTL3 CHG_I_CTL2 CHG_I_CTL3 CHG_PWM CHG_PWM HIDC_MON HIDC_MON CHG_TYPE2 CHG_TYPE2 SCK0 SDO0 XBCK LRCK FS256 XCS_ADC ADDT DIN1 XJACK_DET OPT_DET RMC_DTCK XOPT_CTL XOPT_CTL XPD_ADC XPD_ADC XCS_ADC XJACK_DET OPT_DET DIN1 S0 S1 FS256 ADDT LRCK XBCK S1 S0 RADIO_ON DRAM_HOLD_DET DRAM_VDD_CLR DRAM_ALONE FFCLR XMIC_DET XMIC_DET VOUT VIN VSS NC DVDD1_0 DVSS1_0 DVDD1_1 DVSS1_1 DVDD1_2 DVSS1_2 DVDD1_3 DVSS1_3 DVDD1_4 DVSS1_4 DVDD1_5 DVSS1_5 DVDD1_6 DVSS1_6 DVDD1_7 DVSS1_7 DVDD1_8 DVSS1_8 DVDD1_9 DVSS1_9 DVDD1_10 DVSS1_10 DVDD1_11 DVSS1_11 DVDD3 VSS_3 AVDD1A AVSS1A AVDD1B AVSS1B AVDD1C AVDD2 DVDD25SVAD AVSS2 AVDD3 AVSS3 AVDD4A AVSS4A AVDD4B AVSS4B AVDD4C AVSS4C AVDD5 AVSS5 AVDD6 AVSS6 DAVDD DVDD25LPF DAVSS OSCVDD USBOSCVDD TSMVDD MAIFVDD MSJTAGVDD USBIFVDD VSS_0 VSS_1 VSS_2 IFVDD_1 IFVDD_2 IFVDD_3 IFVDD_4 IFVSS_1 IFVSS_2 DRAMVDD0 DRAMVSS0 DRAMVDD1 DRAMVDD2 DRAMVDD3 DRAMVDD4 DRAMVSS1 DRAMVSS2 FCRAMVDD0 FCRAMVSS0 FCRAMVDD1 FCRAMVSS1 FVDD0 FVSS0 SRAMVDD0 SRAMVSS0 UPUEN UOSCI UOSCO SRAMVDD1 SRAMVSS1 EBIFVDD0 EBIFVSS0 EBIFVDD1 EBIFVSS1 EBIFVDD2 EBIFVSS2 EBIFVDD3 EBIFVSS3 EBIFVDD4 EBIFVSS4 EBIFVDD5 EBIFVSS5 EBIFVDD6 EBIFVSS6 EBIFVDD7 EBIFVSS7 ASYO ASYI RFI PCO FILI FILO CLTV PEAK BOTM ABCD FE VC ADIO ADRB SE TE AUX1 ADRT DCHG APC ADC1EXTC D_VREGO VB_MON CHG_MON VREF_MON SET_KEY_1 SET_KEY_2 DCIN_DET HIDC_MON WK_DET VBUS_MON RMC_KEY RST_CONT RADIO_ON XRST PLL2EXTCI PLL2EXTCO PLL3EXTCI PLL3EXTCO DACVREFH APCREF_DA ADC3VREFH AD3EXTC VIN VREFL AOUTL AOUTR VREFR DCLSOUTR DCLSOUTL RTCK ADFG TFDR FFDR FRDR FS4 SFDR SPRD SPFD SPDV SPDW SPCU SPCV SPCW SLCU SLCV DIN FS256_OUT CHOPPERCLK MNT0 MNT1 MNT2 MNT3 OFTRK RECP SLCW SRDR SLDW SLDV EFMO PAUSE_KEY PROTECT OPT_DET XJACK_DET XMIC_DET OPEN_CLOSE_SW XCS_ADC XPD_ADC NC XRST_LCD USB_WAKE A7CAL_SW SI0 SO0 SCK0 XGUM_ON BEEP XOPT_CTL LAM_REQCHK LAM_SPREQ MDVCC_CTL VBUS_VB_CTL LAM_NAME PF0 SI1 SO1 SCK1 SLD_MON AOUT_SEL YUZU_SLEEP FFCLR CHGI_CTL1 CHGI_CTL2 CHGI_CTL3 SLBUSY XTEST XRF_RST VREC_SEL XHOLD_SW T_MARK_SW XRST2_DET CHGI_SEL RECP_MON SPDL_MON XCS_PWR_IC RXD TXD XCS_LCD XRST_MTR_DRV XCS_NV CHG_PWM IAMP_CAL NC D_VCONT_PWM CHG_OPR_LED XCS_REC_DRV GND_SW CS_RTC JOG_A JOG_B VBUS_DET SSB_DATA SSB_CLK HIMD_PROTECT LDPEN CHG_TYPE2 AD2ENDF TEST SRAM_MODE HSALF TIGER_MON0 TIGER_MON1 TIGER_MON2 TIGER_MON3 TIGER_MON4 TIGER_MON5 TIGER_MON6 TIGER_MON7 TIGER_MON8 TIGER_MON9 XLSRCK TAT TAN NAR IDO SAK LRCKI XBCKI DATAI SI3 SO3 SCK3 SI4 SO4 SCK4 SCS3 SCS4 HI_Z_SLD HI_Z_SPDL SET_CODE0 SET_CODE1 SET_CODE2 SET_CODE3 D_EN1 D_EN2 D_ENVG DADT PWM_L1 PWM_L2 JTAG0 JTAG1 CLKIN2 FS256 ADDT LRCK XBCK OSCI OSCO FS512 DTCK UDP UDM USBHOLD SUSPEND I2C_1 I2C_2 S S * CSP(Chip Size Package) SYSTEM CONTROLLER,DIGITAL SIGNAL PROCESSOR SWITCH WAKE UP HALF_LOCK_SW/OPEN_SW REC_KEY/DOWNLOAD BATT_MINUS_MON TRDR REC_LED/ACCESS_LED PF1/S0DO PF2/S1DO PF3/RTG3 XMUTE/MUTE CC_CTL/VI_CTL DRAM_HOLD_DET DRAM_VDD_CLR B+ SWITCH Q801,802 +2.5V REGULATOR (8/9) (NHF800) DRAM_ALONE 22µH 10µH (Page 31) (Page 33) (Page 26) (Page 28) (Page 25) (Page 27) (Page 28) (Page 30) (Page 33) (Page 33) Ver 1.1

• See page 24 for Waveforms. • See page 36 for IC Block Diagrams. C325 R309 R310 R312 C313 C202 R304 R306 R301 C201 C101 R305 R308 C319 C320 C321 C322 C323 C324 L303 C302 C328 C327 R315 R314 IC302 R103 R203 R101 R201 J30 C102 Q301 C303 C304 C305 C883 L881 D881 C884 C885 C886 R882 R890 R886 R885 Q881 IC881 R881 Q883 C895 R873 C887 R883 R887 D884 D883 D882 Q884 R889 R888 R893 R892 R872 C891 FB301 FB101 FB201 FB303 D302 D303 D301 Q885 IC882 R891 Q886 FB302 D885 R884 C306 C308 R307 R205 R105 D304 C208 C108 C107 C207 IC301 C318 C310 C312 C311 C314 C315 C316 R206 R207 C205 C106 C206 C204 C104 R107 R106 C105 J302 0.1 1k 1k 10 47 6.3V 2.2 100k 10k 1k 100p 100p 100 0 0.1 2.2 6.3V 47 6.3V 0.1 10 6.3V 0.1 2200p 1 1 0 0 XC6219B212MR 22k 22k 47k 47k 2.2 2SA2018TL 0.1 100p 100p 10 6.3V MA2SD32008S0 10 6.3V 1 0.01 470k 220k 100k 1M XP4601-TXE XC6382C251MR 220k UN9214J-(TX).SO 0.1 10k 1 1M 100k MA2Z748001S0 MA2SD32008S0 MA2SD32008S0 XP4314-TX 47k 220k 2.2M 220k 10k 0.1 MAZS068008SO MAZS068008SO MAZS068008SO SI1410EDH-T1 R1180Q221B 0 XP4314-TX MA2Z748001S0 470k 0.1 0.1 100 0 0 MAZS068008SO 4.7 6.3V 4.7 6.3V 47 4V 47 4V AK5356VN-L 2.2 6.3V 10 6.3V 47 6.3V 0.1 0.1 10 6.3V 22 6.3V 10k 22k 0.1 1000p 1000p 2200p 2200p 22k 10k 0.1 L1 M2 M1 P3 P4 L2 SDO0 SCK0 XPD_ADC XCS_ADC XBCK LRCK FS256 ADDT XOPT_CTL DIN1 XJACK_DET OPT_DET GND VB FCRAMVDD XMIC_DET LRCK SDO0 SDO0 SCK0 SCK0 XBCK LRCK FS256 XBCK XCS_ADC XPD_ADC ADDT XOPT_CTL DIN1 XJACK_DET OPT_DET XPD_ADC XCS_ADC FS256 ADDT XOPT_CTL DIN1 XJACK_DET OPT_DET DRAM_ALONE DRAM_VDD_CLR DRAM_HOLD_DET FFCLR XMIC_DET XMIC_DET BCLK MCLK LRCK CDTI CCLK CSN PDN LIN MPWR MRF MVCM MVSS MVDD MICR SDTO DVDD DVSS AVSS AVDD VCOM RIN MICL PREOL PRENL PREL PRER PRENR PREOR VIN VSS CE NC VOUT (9/9) +1.2V REGULATOR A/D CONVERTER LINE B+ SWITCH S VOUT NC CE VSS LX VOUT GND CE VDD (OPT -2 -1 -2 -1 Q885,886 B+ SWITCH VOLTAGE DETECT +2.2V REGULATOR DC/DC CONVERTER Q881,883 REGULATOR CONTROL MIC (PLUG IN POWE -1 -2 100µH 10µH (Page 32) (Page 29) (Page 28) (Page 32) (Page 3

: Uses unleaded solder. • Semiconductor Location Ref. No. Location D151 I-9 D301 D-9 D304 D-9 D436 I-9 D439 H-8 D440 D-7 D457 C-9 D458 D-5 D473 I-9 D605 I-6 D606 I-6 D607 I-6 D608 I-6 D614 H-5 D615 I-5 D616 I-6 D881 F-1 D882 E-1 D883 E-1 D884 D-2 D885 D-1 D902 G-5 D904 H-4 D905 F-4 D906 H-4 IC471 I-9 IC502 D-5 IC701 E-6 IC881 F-2 IC882 F-1 IC892 I-4 IC901 G-4 Q403 D-8 Q406 D-8 Q407 I-5 Q432 D-7 Q433 E-8 Q451 D-7 Q452 D-5 Q501 E-5 Q502 D-4 Q503 D-4 Q601 I-6 Q602 I-6 Q603 I-6 Q616 H-5 Q617 G-5 Q803 I-3 Q881 F-3 Q883 F-2 Q884 D-2 Q885 D-2 Q886 D-2 Q902 H-3 C836 + C838 + C816 + C883 + C940 + C948 + C939 + C845 + C818 + C850 C821 R826 R839 R840 C817 R864 R856 R863 R830 R876 R829 C861 C828 C835 R809 R813 R895 C892 R855 R897 R878 R824 C820 C929 R920 R954 R958 C928 C927 C954 C926 R918 R917 R903 R906 R659 C920 C713 C712 R712 R713 C709 C710 R709 C702 C707 C708 R710 C706 C717 C705 R711 R708 C703 R516 R515 R561 R466 R463 R464 R663 R662 C908 R661 R660 R879 R865 C810 R825 R866 R622 C903 C902 R951 R953 C895 R930 R927 R929 R926 R936 R934 R935 R933 R925 R873 R884 R886 R890 R822 R821 R818 R819 C839 R960 R894 R880 R833 C827 R837 R857 R858 R842 R959 C843 C814 C846 R922 C932 R955 C960 C959 R904 R907 R964 C715 R507 C568 C573 R508 C558 R513 CN501 R514 C560 R467 R504 R462 C714 R503 C569 R522 R521 C811 R908 R910 R912 C901 C649 C676 R620 C646 R624 R621 R625 C648 R623 C823 R924 R931 R914 R841 R952 C886 R887 R885 R882 R883 R881 R938 R937 C832 FB810 FB809 FB802 FB803 C958 L802 C808 C885 IC881 IC882 C887 C933 C936 C931 C935 C937 C864 L803 L804 L801 C833 C812 L881 D881 K A + C884 E C B Q883 D883 D882 K A K A D884 D885 K A A K R889 R892 C891 R872 R891 R888 R893 Q885 Q884 Q886 Q881 Q902 E C B Q803 IC892 IC901 D904 D906 D615 D606 A K D902 A K D905 K A A K K A D439 K A A K D607 D616 A K A K L903 L904 L507 L505 L501 L805 C819 + C923 + C650 + C922 + C909 + + C915 + C916 + C564 + C570 + C402 + C403 + C426 E C B Q407 Q601 Q602 Q603 R668 C919 C562 C453 R433 R432 C452 C561 FB503 FB502 C906 C918 R680 THP401 LF401 C480 C481 Q616 Q617 D614 K A D436 D473 K A K A D605 A K D608 A K L606 R491 R490 R489 R486 R476 R162 R477 R418 R424 R421 R423 R422 C716 R707 R706 C701 R351 C419 C420 R420 R156 R161 R160 C311 R260 R261 R256 C353 R437 R438 C305 C201 C101 C303 FB302 C416 R419 D151 A K 1 3 5 4 IC471 L9001 L351 C208 + C108 + C312 + C310 + + C352 + C318 + C207 + C107 + C320 + C160 + C260 L607 Q433 Q432 Q403 Q406 Q451 B C E + C924 Q501 Q452 Q502 B C E E C B Q503 IC502 IC701 D458 K A D440 K A J301 J352 CN451 (USB) CN451 (FRONT VIEW) D457 A K MAIN BOARD (COMPONENT SIDE) 1-861-364- 45 31 1 15 16 30 60 46 1 4 8 5 1 5 6 7 S893 OPEN/CLOSE DETECT i (11) 11 1C 2B 2E 1C 2E 2B 1E 2C 1B E B C 1E 1B 2C G D D D 1 2 4 1 26 3 1 16 48 33 17 32 64 49 G D D S S D D D 1D 2S 2G 1S 2D 1G 1C 2E 2B 1E 2C G D S D D D 5 8 4 1 1B 2D 1G 1S 2S 2G 1D 2D 1D 2G S 1G 1C 2B 2E 1E 1B 2C 2C 1B 1E 3 1 4 5 1 2 4 3 2E 2B 1C OPTICAL PICK-UP BLOCK (ABX-U) 2C 1B 1E G D S D D D 2E 2B 1C 2E 2B 1C 2C 1B 1E A B C D E F G H I 1 2 3 4 5 6 7 8 9 10 11 D301 D304 A K A K S894 S894-1 PROTECT DETECT -1 -2 S894-2 Hi-MD PROTECT DETECT LINE IN (OPT) DIN DGND DVCC (AEP, UK, EE) (AEP, UK, EE) (NHF800)

: Uses unleaded solder. • Semiconductor Location Ref. No. Location D251 H-3 D302 D-2 D303 D-3 D352 G-2 D401 I-5 D435 D-4 D441 D-10 D471 H-3 D601 G-5 D602 G-6 D603 F-7 D604 F-5 D609 F-5 D610 F-4 D611 E-8 D613 G-4 D801 I-7 D803 I-8 IC301 F-3 IC302 D-4 IC352 G-3 IC401 I-5 IC402 D-8 IC501 D-9 IC601 G-6 IC602 H-4 IC603 D-7 IC604 F-11 IC605 H-5 IC606 H-4 IC607 H-4 IC801 H-9 IC804 I-7 IC902 H-7 Q301 D-3 Q351 F-4 Q352 F-2 Q353 F-2 Q401 I-4 Q471 H-3 Q504 E-10 Q607 E-4 Q608 E-4 Q609 H-6 Q611 E-5 Q612 G-7 Q613 E-7 Q614 E-7 Q615 E-8 Q618 H-4 Q801 I-7 Q802 H-7 Q901 F-8 C427 (CHASSIS) R511 R868 R512 C533 C531 C527 C559 C822 R802 R806 R807 R801 C604 R678 R643 R353 R252 R254 R253 R358 R154 R153 R152 R258 R257 R158 R157 R251 C364 R355 R151 R354 C625 R652 R485 R480 C479 R483 R484 C429 C476 R472 R473 R471 C361 R474 R475 R612 R671 R628 R665 C642 R617 R629 C645 C638 R673 R435 C415 C406 C412 C407 C421 R446 R447 C673 R434 R425 R804 C853 R832 C830 R862 R861 R646 R681 C633 R805 C611 C408 R436 C671 R685 C677 R683 C602 C630 R654 R647 R679 R605 C620 R645 C675 R653 R670 R867 C856 C961 R860 R520 R524 R812 R817 C809 C857 R820 R869 C803 C574 C554 R505 C520 R443 R442 C434 C519 C517 C516 C521 C511 R639 C644 R675 R312 R315 W404 R618 R314 R601 R455 R456 R619 C322 C319 C324 C430 C314 R101 R201 R203 R301 C455 C461 R305 C325 R310 R309 C425 C636 R352 R356 R103 C306 C106 R106 R206 C206 C105 C104 R105 C308 R307 R107 R207 R205 C204 C205 C151 C152 C251 C252 R255 R262 R682 R684 R155 C478 CN471 R478 R359 C363 R609 R616 C641 R638 C515 C557 C522 C523 C513 R657 R642 FB501 R641 R640 R636 R441 R444 C528 C536 C550 C552 C538 R502 R501 C529 C525 C547 C526 C804 R815 R811 R823 C860 C555 C565 R843 C847 VDR801 R827 R810 R519 R518 R517 C566 R509 C545 C669 SL802 IC604 IC801 IC804 IC401 IC605 IC606 IC607 C668 C805 E C B Q504 C802 C801 C858 C859 R808 FB807 X802 C567 + L506 L504 L502 + C556 + C652 + C635 C666 C672 + C637 IC501 IC603 C530 C438 C524 C537 C539 R525 R526 C661 C660 R650 R635 C553 + C518 + L503 D611 Q615 Q901 Q614 K A Q613 G D S L907 L906 L901 FB801 C634 R648 C327 R308 C102 C328 R677 R664 L608 R649 C628 R845 C674 X801 Q802 Q609 Q401 S D G Q801 D803 A K + C622 C411 + C627 + C616 + C614 + C613 + L601 D602 K A D603 A K Q612 S D G SL901 L603 L701 L702 CN701 C423 + C424 + L605 C653 + C612 + C621 + C356 + C321 + C643 Q611 Q608 E C B Q607 D604 A K + C658 + C354 F351 F1 + C323 D609 D613 D610 A K A K IC601 D401 K A C607 C609 R608 C355 C351 C253 C153 C154 C254 C601 FB471 FB357 FB2 FB353 FB354 FB1 FB355 C619 D601 K A K A L303 IC302 D435 A K D303 D302 K A K A C315 + C313 + C316 + R306 R304 FB303 C456 C458 C459 C304 C460 C302 IC301 IC352 Q351 B C E IC602 D251 D471 Q471 K A K A Q618 D352 Q353 Q352 C202 FB201 E C B Q301 FB301 FB101 LF451 R454 C457 FB452 FB451 BP701 SL894 SL892 SL891 S892 (HALF LOCK) J402 MAIN BOARD (CONDUCTOR SIDE) (11) 11 1-861-364- 1 7 21 15 14 8 22 28 U U N V W N V W M702 (SLED) M701 (SPINDLE) M703 OVER WRITE HEAD UP/DOWN M 1 10 DRY BATTERY SIZE "AA" (IEC DESIGNATION R6) 1PC. 1.5V 1 1C 2B 2E 1 10 1E 1B 2C 3 5 4 2C 1B 1E D G D D D S D G D D D S D G D D D S K K 1C 1 4 5 3 1 6 18 13 12 19 24 7 2C 1B E 2B K K A 2E 2B 1C 1 16 LCD MODULE 1 3 4 2 1 1 3 5 5 8 4 1 1 2 4 3 4 2 4 3 E C B ∗ ∗ ∗ ∗ G D S HR601 OVER WRITE HEAD SL801 1 4 8 5 1 1 3 5 4 3 5 4 2C 1B 1E 2E 2B 1C 4 3 1 2 A B C D E F G H I J 1 2 3 4 5 6 7 8 9 10 11 57 56 54 52 49 45 41 37 34 32 30 29 58 59 55 53 50 46 42 38 35 33 31 28 84 87 89 91 94 98 102106 109 111 3 2 85 86 88 90 93 97 101105 108 110 112 1 62 63 64 51 47 43 39 36 25 24 65 66 67 68 48 44 40 23 22 21 77 78 79 96 100104 12 11 10 9 80 81 92 95 99 103107 8 7 6 69 70 71 72 20 19 18 17 73 74 75 76 16 15 14 13 60 61 27 26 82 83 5 4 5451 48 45 43 42 40 37 34 31 5552 49 47 44 41 38 36 33 30 5653 50 46 39 35 32 29 1 4 7 11 18 22 25 28 2 5 8 10 13 16 19 21 24 27 3 6 9 12 14 15 17 20 23 26 D441 A K IC902 1 2 4 3 2C 1B 1E 2E 2B 1C (CHASSIS) (CHASSIS) W403 (CHASSIS) IC402 CL8027 CL8001 CL8055 CL921 CL919 CL931 CL935 CL658 CL604 CL433 (GND) CL432 (BATT–) CL460 (VBUS GND) CL453 (VBUS 5V) MIC (PLUG IN POWER) J302 DC IN 3V − + CL431 (BATT+) D801 A K

IC301 AK5356VN-L V REF MT SW BST SW BEEP 19 20 21 22 23 24 18 17 16 15 14 13 PW SW 12 11 10 8 7 BST1 9 BST2 6 5 4 3 2 1 BST AGC PW B PW A ADD MT TC VCC1 INB INA BEEP OUTB BEEP OUTA VCC2 OUTA PWR GND OUTB DET AGC IN BST OUT BST NF2 LPF2 BST NF1 LPF1 VREF VREF IN GND BEEP IN BST SW MT SW PW SW C352 TA2131FLG (EL) LIN 28 A/D CONVERTER AUDIO INTERFACE CONTROLLER CDTI 11 SDTO MICL PREOL PRENL PREL PRER PRENR PREOR 7 RIN 1 VCOM 2 AVDD 3 AVSS 4 DVSS 5 DVDD 6 CSN 13 CCLK 12 LRCK 10 MCLK 9 BCLK 8 CONTROL REGISTER INTERFACE MIC POWER SUPPLY PDN RESET 14 17 16 15 18 19 20 21 MPWR 27 MRF 26 MVSS 24 MVDD 23 MICR 22 MVCM VCOM VCOM 25 IC501 SN761059ZQLR RF PEAK/ BOTTOM SERIAL INTERFACE ABCD 1 2 3 4 5 6 10 11 12 13 14 38 37 36 35 34 33 32 31 30 29 16 15 17 18 19 20 22 21 23 24 25 8 9 7 LX PS EQ AGND OFC-C1 OFC-C2 RF_LX RF_LY RF_JY RF_JX D-C RFO VREF09 VREF10 28 27 26 PDO-SINK A-C PDO-SOURCE PD-I PD-NI PD-BUF WPP-LPF SMON ADFG CDN CCSL2 CN CPGND CLK 42 41 40 39 VC CIG DGND XRESET VGIN SBUS SCK CPOUT CP DVCC TE FE ABCD ADIP-IN 43 47 48 51 52 49 50 53 54 55 56 FE TE POWER SUPPLY T-ON APC TPP/WPP OFTRK ADIP 45 46 VCC VCC2 VCC 44 NPPO BOTM PEAK B C D A AVCC JX JY LY OFTRK TON-C AVCC2 VCC2 TEMP VREF09 A-C D-C MALFA MIJ AWBPF DW DWBPF OFTTH APC ADIP-BPF VFREF0.4 I-J A+B+C+D I+J NPP TON CSL AW+DW TON PEAK TON BOTM ADIP TE TWPP PK/BTM AW CSLO S-MONITOR VREF + – + – + – + – A/D CONVERTER A/D VREF VREF A7CAL_SW 13 WDT 10 LED_CTL 9 IAMP_CTL 14 CFB 15 TYPE1 11 BAT+ 31 CHG_SW1 30 I_CTL2 29 BAT– 25 RF1 26 IAMP_CAL 27 AMP_SEL 28 VO 32 22 I_CTL3 23 RS 24 I_CTL1 20 I_SEL 18 AD_SEL 17 VI 6 CHG_SW2 5 VI_CTL 4 PWT 3 VG 2 VI2 1 GND 21 PGND 19 SWITCHING CIRCUIT TIME DIVIDER ERROR LED CONTROL OSC DET COMPARATOR BLOCK IN1– 12 CHG_CTL 7 TYPE2 16 CHARGE CONTROL ON/OFF CHARGE SWITCH CONTROL CHARGE CONTROL ON/OFF CONTROL RECEIVER PWR_WAKE 8 WAKE-UP CONTROL SWITCHING IC401 MM1655NCBE

30 RF3 31 DTC3 32 INM3 33 INM2 34 DTC2 35 RF2 36 VPDRV 37 POWP1 38 CLP 39 INP2 40 INP3 41 POWP2 42 CLM 43 VBUSSEL 44 PGND5 45 L5 1 46 POWFB 47 PGND5 48 PGND5 19 PGND3 20 PGND3 21 V3C 1 22 V3C 2 23 33USEL 24 L3 1 25 L3 2 26 DW 3T 27 DW 3B 28 V3FB 49 L5 2 50 VBUSREF 51 VBUS DET 52 V33UO 53 WAKEC 54 VBUS 55 XWKO 56 LATCH 62 EFM 63 EFM CLK 64 VBUSSEL2 65 PGND4 66 VG3 67 RECP 68 GND 69 HBB 70 HAB 71 CH 72 GND 73 VG2 74 VCP 75 CL 76 PGND4 77 HB 78 HA 79 PGND2 80 VRECIN 81 VRECIN 82 OUTB 83 VG 84 OUTA 89 CRST 90 DVDD IN 91 DVDD OUT 92 HOLDC 93 OSC OUT 94 SLEEP IN 95 RST IN 96 PGND2 97 REG IN 98 REG OUT 99 SUS IN 100 PGND2 101 TSBV IN 102 TSBV OUT 103 V33R 104 PGND1 105 VSTB IN 106 VSTB OUT 107 BATSEL 108 V33RO 109 RF1 110 INM1 111 DTC1 112 VREC HOLD LOGIC BUFFER CHARGE PUMP PVBUS VG VREC POWER SWITCH DRIVER CIRCUIT 2.0V RESET RESET LOGIC VREC STEP UP-DOWN CONVERTER DRIVER PWM V3 STEP UP-DOWN CONVERTER DRIVER PWM VC V3FB VREF BUFFER DAC VPDRV VBUS VBUS VG3 VIF H-BRIDGE DRIVER CONTROL SYSTEM BUS POWER STEP DOWN CONVERTER DRIVER SELFPOWER STEP UP-DOWN CONVERTER DRIVER BANDGAP REFERENCE DAC WAKE LVDT LVDT CONTROL EFM TOP PRE DRIVER EFM BOTTOM PRE DRIVER IC601 SC901585VAR2

38 MZ-NH700/NHF800 1 2 VDD GND CE REGULATOR CURRENT LIMIT 3 VOUT 5 ECO 4 IC602 R1160N121B-TR-FA 1 2 3 5 4 + – BUFFER VLX LIMITER CHIP ENABLE REFERENCE VOLTAGE PFM CONTROL OSC 100kHz VDD CE VOUT NC LX VSS IC881 XC6382C251MR 18 17 FO1 VMF1 31 VMF2 1 DECODER PRE DRIVE 64 WI1 3 WO1 4 ST1 2 PGNDW1 8 PGNDUV1 5 VMVW1 11 VMU1 VI1 49 VI2 63 UI1 50 UI2 62 PWM1 61 CPUO1 60 CPVO1 59 CPWO1 51 PWM2 52 CPUO2 53 CPVO2 54 CPWO2 STANDBY 55 STALL 56 GND 57 VCC 58 VG DECODER 7 VO1 6 VO1 10 UO1 9 UO1 12 VMR1 15 PGND1 14 RO1 13 RO1 16 FO1 32 FO2 19 FI1 20 RI1 29 RI2 30 FI2 21 COM1 22 CPUI1 23 CPVI1 VG PRE DRIVE VG VG VG PRE DRIVE VG PRE DRIVE + – + – 24 CPWI1 25 CPWI2 26 CPVI2 27 CPUI2 28 COM2 + – + – + – + – 33 FO2 34 PGND2 37 VMR2 38 VMU2 39 UO2 40 UO2 42 VO2 43 VO2 46 WO2 45 ST2 44 VMVW2 47 PGNDW2 48 WI2 41 PGNDUV2 35 RO2 36 RO2 IC701 BD6607KN

SENSE AMP CONTROL LOGIC SERIAL-PARALLEL CONVERTER XCS SDO XWP VSS VCC XHOLD SCL SDI IC901 SC901584EPR2 POWER SWITCH 2 SERIAL PASS REGULATOR 3 49 REGC2 50 REG2G 51 REGO2 52 REGI2 53 REGC1 54 REGO1 55 REGI1 22 INM1 21 RF1 58 DATA 59 STRB 60 CLK 61 WDT 62 SEQSEL 63 CLK 64 SLEEP 1 FFCLR 2 XWK4 3 XWK3 4 XWK2 5 XWK1 LVB 6 VRMC FFCLR 7 HVB 8 VTSB 9 VC1 10 VCO1 11 VO1 13 L1 14 L1 15 PGND1 16 PGND1 12 34 XRST2 33 CRST2 20 DTC1 19 XRST1ADJ 18 CRST1 17 XRST1 25 LG 24 VG 26 PGND3 23 C1L 29 VGSEL1 28 VGSEL2 30 INM2 31 RF2 32 DTC2 RST2 REF2 VG SELECT, VG DUTY CLK 36 PGND2 35 PGND2 L2 37 L2 38 VO2 39 VCO2 40 VCIN 41 VC2 42 DW 2T 43 DW 2B 44 MUTEON 45 REGC3 46 REGO3 47 REGI3 48 SERIAL PASS REGULATOR 2 SERIAL PASS REGULATOR 1 RST1 RST2 SEQSEL MUTE ON MUTING BUFFER VC2 RST2 POWER SWITCH 1 RST2 STEP UP-DOWN DRIVER PWM START UP RESET 2 VC2 REF2 VREF VB REF1 VC VREF 27 VB STEP UP DC/DC CONVERTER CONTROL REF1 REF2 REF3 REF4 REF5 REF DAC VREF0 RST1 LVB DRIVER VREF VC VC STEP UP-DOWN DRIVER PWM VREF RESET 1 VC RST1 VREF REF1 56 GND 57 VREF VC VREF0 BANDGAP REFERENCE

Pin No. Pin Name I/O Description 1 DVDD1_0 — Power supply terminal 2 DVSS1_0 — Ground terminal 3 DVDD1_1 — Power supply terminal 4 DVSS1_1 — Ground terminal 5 DVDD1_2 — Power supply terminal 6 DVSS1_2 — Ground terminal 7 DVDD1_3 — Power supply terminal 8 DVSS1_3 — Ground terminal 9 DVDD1_4 — Power supply terminal 10 DVSS1_4 — Ground terminal 11 DVDD1_5 — Power supply terminal 12 DVSS1_5 — Ground terminal 13 DVDD1_6 — Power supply terminal 14 DVSS1_6 — Ground terminal 15 DVDD1_7 — Power supply terminal 16 DVSS1_7 — Ground terminal 17 DVDD1_8 — Power supply terminal 18 DVSS1_8 — Ground terminal 19 DVDD1_9 — Power supply terminal 20 DVSS1_9 — Ground terminal 21 DVDD3 — Power supply terminal 22 VSS_3 — Ground terminal 23 DVDD1_10 — Power supply terminal 24 DVSS1_10 — Ground terminal 25 DVDD1_11 — Power supply terminal 26 DVSS1_11 — Ground terminal 27 AVDD1A — Power supply terminal (for PLL) 28 AVSS1A — Ground terminal (for PLL) 29 AVDD1B — Power supply terminal 30 AVSS1B — Ground terminal 31 AVDD1C — Power supply terminal 32 AVDD2 — Power supply terminal (for A/D converter) 33 DVDD25SVADC — Power supply terminal (for A/D converter) 34 AVSS2 — Ground terminal (for A/D converter) 35 AVDD3 — Power supply terminal (for A/D converter) 36 AVSS3 — Ground terminal (for A/D converter) 37 AVDD4A — Power supply terminal (for PLL) 38 AVSS4A — Ground terminal (for PLL) 39 AVDD4B — Power supply terminal (for PLL) 40 AVSS4B — Ground terminal (for PLL) 41 AVDD4C — Power supply terminal (for D/A converter) 42 AVSS4C — Ground terminal (for D/A converter) 43 AVDD5 — Power supply terminal (for PLL) 44 AVSS5 — Ground terminal (for PLL) 45 AVDD6 — Power supply terminal (for A/D converter) 46 AVSS6 — Ground terminal (for A/D converter) • IC Pin Function Description Ver 1.1

48 DVDD25LPF — Power supply terminal (for D/A converter) 49 DAVSS — Ground terminal (for D/A converter) 50 OSCVDD — Power supply terminal (for 22 MHz OSC) 51 USBOSCVDD — Power supply terminal (for the USB 48 MHz OSC) 52 TSMVDD — Power supply terminal (for the TSB master communication) 53 MAIFVDD — Power supply terminal (for MA interface) 54 MSJTAGVDD — Power supply terminal (for AUX) 55 USBIFVDD — Power supply terminal (for USB interface) 56 to 58 VSS_0 to VSS_2 — Ground terminal 59 to 62 IFVDD_1 to IFVDD_4 — Power supply terminal (for interface) 63 IFVSS_1 — Ground terminal (for interface) 64 IFVSS_2 — Ground terminal (for interface) 65 to 69 DRAMVDD0 to DRAMVDD4 — Power supply terminal (for D-RAM/DSP interface) 70 to 72 DRAMVSS0 to DRAMVSS2 — Ground terminal (for D-RAM/DSP interface) 73 FCRAMVDD0 — Power supply terminal (for D-RAM) 74 FCRAMVSS0 — Ground terminal (for D-RAM) 75 FCRAMVDD1 — Power supply terminal (for D-RAM) 76 FCRAMVSS1 — Ground terminal (for D-RAM) 77 FVDD0 — Power supply terminal (for AUX) 78 FVSS0 — Ground terminal (for AUX) 79 SRAMVDD0 — Power supply terminal (for AUX) 80 SRAMVSS0 — Ground terminal (for AUX) 81 SRAMVDD1 — Power supply terminal (for AUX) 82 SRAMVSS1 — Ground terminal (for AUX) 83 EBIFVDD0 — Power supply terminal (for interface circuit) 84 EBIFVSS0 — Ground terminal (for interface circuit) 85 EBIFVDD1 — Power supply terminal (for interface circuit) 86 EBIFVSS1 — Ground terminal (for interface circuit) 87 EBIFVDD2 — Power supply terminal (for interface circuit) 88 EBIFVSS2 — Ground terminal (for interface circuit) 89 EBIFVDD3 — Power supply terminal (for interface circuit) 90 EBIFVSS3 — Ground terminal (for interface circuit) 91 EBIFVDD4 — Power supply terminal (for interface circuit) 92 EBIFVSS4 — Ground terminal (for interface circuit) 93 EBIFVDD5 — Power supply terminal (for interface circuit) 94 EBIFVSS5 — Ground terminal (for interface circuit) 95 EBIFVDD6 — Power supply terminal (for interface circuit) 96 EBIFVSS6 — Ground terminal (for interface circuit) 97 EBIFVDD7 — Power supply terminal (for interface circuit) 98 EBIFVSS7 — Ground terminal (for interface circuit) 99 ASYO O Playback EFM duplex signal output 100 ASYI I Playback EFM comparator slice level input 101 RFI I Playback EFM RF signal input from the RF amplifier

103 FILI I Filter input terminal for the playback EFM system master PLL 104 FILO O Filter output terminal for the playback EFM system master PLL 105 CLTV I Internal VCO control voltage input terminal for the playback EFM system master PLL 106 PEAK I Peak hold signal input of the light amount signal (RF/ABCD) the RF amplifier 107 BOTM I Bottom hold signal input of the light amount signal (RF/ABCD) the RF amplifier 108 ABCD I Light amount signal (ABCD) input from the RF amplifier 109 FE I Focus error signal input from the RF amplifier 110 VC I Middle point voltage input from the RF amplifier 111 ADIO O Monitor output terminal of A/D converter input signal Not used 112 ADRB I A/D converter the lower limit voltage input terminal 113 SE I Sled error signal input from the RF amplifier 114 TE I Tracking error signal input from the RF amplifier 115 AUX1 I Auxiliary A/D input terminal 116 ADRT I The upper limit voltage of A/D converter input terminal Not used 117 DCHG — Connecting terminal with the analog power supply of low impedance 118 APC I Error signal input for the laser automatic power control 119 ADC1EXTC — Connection terminal for an external capacitor 120 D_VREGO I Voltage sensibility of regulator for class-D amplifier Not used 121 VB_MON I Unregulated power supply voltage monitoring terminal 122 CHG_MON I Charge or discharge current monitoring terminal Not used 123 VREF_MON I Reference voltage input terminal 124 SET_KEY_1 I Front panel key input terminal 125 SET_KEY_2 I Front panel key input terminal 126 DCIN_DET I DC input voltage for battery charge monitoring terminal Not used 127 HIDC_MON I High DC voltage monitoring terminal 128 WK_DET I Panel key input for wake-up 129 VBUS_MON I USB power supply voltage monitoring terminal 130 BATT_MINUS _MON I Voltage monitoring terminal for the minus terminal of rechargeable battery 131 RMC_KEY I Remote commander key input terminal 132 RST_CONT O System reset signal output to the power control IC 133 REC_KEY /DOWNLOAD I DOWNLOAD key input terminal 134 RADIO_ON I Radio on detection input from the remote commander jack 135 HALF_LOCK_ SW /OPEN_SW I Front panel open switch detection terminal 136 XRST I System reset signal input from the power control IC 137 PLL2EXTCI I Connection terminal for an external capacitor 138 PLL2EXTCO O Connection terminal for an external capacitor 139 PLL3EXTCI I Connection terminal for an external capacitor 140 PLL3EXTCO O Connection terminal for an external capacitor 141 DACVREFH I Reference voltage input terminal 142 APCREF_DA O Reference voltage output terminal 143 ADC3VREFH I Reference voltage input terminal 144 ADC3EXTC — Connection terminal for an external capacitor 145 VIN I RF signal input from the RF amplifier

147 AOUTL O Built-in D/A converter L-CH signal output 148 AOUTR O Built-in D/A converter R-CH signal output 149 VREFR I Reference voltage terminal connected to the capacitor (for the built-in D/A converter R-CH) 150 DCLSOUTR O PWM modulator signal output for the class-D headphone amplifier Not used 151 DCLSOUTL O PWM modulator signal output for the class-D headphone amplifier Not used 152 RTCK — Not used 153 ADFG I ADIP duplex FM signal (22.05±1kHz) input from the RF amplifier 154 TRDR O Tracking servo drive PWM signal output (–) to the coil driver 155 TFDR O Tracking servo drive PWM signal output (+) to the coil driver 156 FFDR O Focus servo drive PWM signal output (+) to the coil driver 157 FRDR O Focus servo drive PWM signal output (–) to the coil driver 158 FS4 O 176.4 kHz clock signal output 159 SFDR O Sled servo drive PWM signal output to the motor driver 160 SPRD O Spindle motor drive control signal output (U) to the motor driver 161 SPFD O Spindle servo drive PWM signal output to the motor driver 162 SPDV O Spindle motor drive control signal output (V) to the motor driver 163 SPDW O Spindle motor drive control signal output (W) to the motor driver 164 SPCU I Spindle motor drive comparison signal input (U) from the motor driver 165 SPCV I Spindle motor drive comparison signal input (V) from the motor driver 166 SPCW I Spindle motor drive comparison signal input (W) from the motor driver 167 SLDV O Sled motor drive control signal output (V) to the motor driver 168 SLDW O Sled motor drive control signal output (W) to the motor driver 169 SLCU I Sled motor drive comparison signal input (U) from the motor driver 170 SLCV I Sled motor drive comparison signal input (V) from the motor driver 171 SLCW I Sled motor drive comparison signal input (W) from the motor driver 172 SRDR O Sled motor drive control signal output (U) to the motor driver 173 DIN I Digital audio signal input terminal 174 FS256_OUT O 11.2896 MHz clock output 175 CHOPPERCLK O Clock signal output for chopper 176 to 179 MNT0 to MNT3 O Monitor output for DSP 180 OFTRK I/O Tracking signal input/output for MD3 181 RECP O Laser power changeover signal output 182 EFMO O EFM encode data output for the record 183 PAUSE_KEY I Pause key input terminal 184 PROTECT I Recording protector detection input for normal disc 185 OPT_DET I Optical digital input plug detection input terminal “H”: optical in 186 XJACK_DET I Line input plug detection input terminal “L”: plug in 187 XMIC_DET I Microphone input plug detection input terminal “L”: plug in 188 OPEN_CLOSE _SW I Open switch input terminal 189 XCS_ADC O Chip select signal output for A/D converter 190 XPD_ADC O Power control signal output for A/D converter 191 NC — Not used 192 XRST_LCD O Reset signal output for the LCD module 193 USB_WAKE I System wake up signal input by USB connect 194 A7CAL_SW O A7 offset voltage CAL on/off control signal output terminal Not used

196 SO0 O Serial data output to the EEPROM, A/D converter and controllers 197 SCK0 O Serial clock output to the EEPROM, A/D converter and controllers 198 XGUM_ON I Rechargeable battery detection signal input terminal Not used 199 BEEP O Beep sound control signal output to the headphone amplifier 200 XOPT_CTL O Power supply on/off control signal output for the optical input jack 201 LAM_REQCHK I LAM power check terminal Not used 202 LAM_SPREQ O LAM force stop request signal output Not used 203 REC_LED /ACCESS_LED O REC or Access LED drive signal output terminal Not used 204 MDVCC_CTL O Power supply control signal output for the OP modulation 205 VBUS_VB_CTL O USB power supply control signal output terminal 206 LAM_NAME O LAM name data request signal output terminal Not used 207 DRAM_ALONE O Self-refresh signal output for internal D-RAM 208 PF0 — Not used 209 PF1/S0DO O Connect to the optical pick-up block 210 PF2/S1DO O Connect to the optical pick-up block 211 PF3/RTG3 O Connect to the headphone amplifier 212 XMUTE /MUTE O Muting on/off control signal output terminal 213 SI1 I Serial data input from the LCD module 214 SO1 O Serial data output to the LCD module 215 SCK1 I/O Serial data transfer clock signal input/output terminal with the LCD module 216 SLD_MON I Sled servo monitoring terminal 217 AOUT_SEL O Headphone/line output switching terminal Not used 218 YUZU_SLEEP O Chip enable output to the power control IC 219 FFCLR O Power on/off control signal output for FCRAM (internal RAM) 220 CHGI_CTL1 O Charge current limiter control signal output at the time of DC adaptor use “L”: charge Not used 221 CHGI_CTL2 O Charge current control signal output terminal “L”: low current charge 222 CHGI_CTL3 O Charge current control signal output terminal “L”: low current charge 223 SLBUSY I Receive signal monitoring terminal for sled command 224 XTEST I Terminal for the test mode setting (normally open) “L”: test mode 225 XRF_RST O Reset signal output to the RF amplifier 226 VREC_SEL O VREC start-up timing control signal output terminal 227 XHOLD_SW I HOLD switch detection input terminal 228 T_MARK_SW I Track mark switch input terminal Not used 229 XRST2_DET I Reset signal input from the power control IC 230 CHGI_SEL O Charge/discharge control signal output for current sense amplifier Not used 231 RECP_MON I Laser power changeover signal monitoring terminal 232 SPDL_MON I Spindle servo monitoring terminal 233 XCS_PWR_IC O Chip select signal output to the power control IC 234 RXD I Not used 235 TXD O Not used 236 XCS_LCD O Chip select signal output to the LCD module 237 CC_CTL /VI_CTL O Constant current circuit control signal output terminal

239 XCS_NV O Chip select signal output to the EEPROM 240 CHG_PWM O Charge current or voltage control signal output terminal 241 IAMP_CAL O Offset signal output of current sense amplifier Not used 242 NC — Not used 243 D_VCONT _PWM O For voltage control signal output terminal for class-D amplifier Not used 244 CHG_OPR_LED O Charge indication LED drive signal output terminal Not used 245 XCS_REC_DRV O Chip select signal output to the over write head driver 246 GND_SW O Ground line switching signal output terminal 247 CS_RTC O Chip select signal output for real time clock Not used 248 JOG_A I Jog dial pulse input terminal 249 JOG_B I Jog dial pulse input terminal 250 VBUS_DET I USB power supply voltage detection terminal 251 SSB_DATA I/O SSB data input/output with the RF amplifier 252 SSB_CLK O SSB clock output to the RF amplifier 253 HIMD_ PROTECT I Recording protector detection input for Hi-MD disc 254 LDPEN O Pulse/DC light-emit switching signal output terminal 255 CHG_TYPE2 O Battery charge control signal output terminal “H”: charging 256 DRAM_HOLD _DET I Detection terminal for internal D-RAM power supply information keeping 257 DRAM_VDD _CLR O Internal D-RAM power latch clear signal output for quick mode sleep 258 AD2ENDF I Monitoring terminal for flag of servo signal A/D measuring finish 259 TEST — Not used 260 SRAM_MODE I Not used 261 HSALF I Not used 262 to 271 TIGER_MON0 to TIGER_MON9 O Trigger monitoring terminal output clock=18.5 MHz 272 XLSRCK O Pulse output for laser strobe recording 273 TAT — Not used 274 TAN — Not used 275 NAR — Not used 276 IDO — Not used 277 SAK — Not used 278 LRCKI I L/R sampling clock signal input terminal for PCM data interface Not used 279 XBCKI I Bit clock signal input terminal for the PCM data interface Not used 280 DATAI I Serial clock signal input terminal for the PCM data interface Not used 281 SI3 I Serial data input for LAM microcomputer communication Not used 282 SO3 O Serial data output for LAM microcomputer communication Not used 283 SCK3 O Serial data transfer clock signal output for LAM microcomputer communication Not used 284 SI4 I Data input from ATRAC3 plus encoder communication Not used 285 SO4 O Data output for ATRAC3 plus encoder communication Not used 286 SCK4 O Clock signal output for ATRAC3 plus encoder communication Not used 287 SCS3 O Chip select signal output for LAM microcomputer communication Not used

289 HI_Z_SLD O Standby signal output terminal for the sled motor 290 HI_Z_SPDL O Standby signal output terminal for the spindle motor 291 to 294 SET_CODE0 to SET_CODE3 I Setting terminal for the destination 295 D_EN1 O Control signal output for class-D amplifier Not used 296 D_EN2 O Control signal output for class-D amplifier Not used 297 D_ENVG O Enable/disable switching control terminal for class-D amplifier booster circuit Not used 298 DADT O Audio data output terminal Not used 299 PWM_L1 O LC drive PWM output terminal 300 PWM_L2 O LC drive PWM output terminal 301 I2C 1 — Open drain for IIC 302 I2C 2 — Open drain for IIC 303, 304 TEST — Not used 305 CLKIN2 I Clock signal input terminal (13.5 MHz or 27 MHz) Not used 306 FS256 O Master clock signal (256Fs=11.2896 MHz) output to A/D converter 307 ADDT I Data input from A/D converter 308 LRCK O L/R sampling clock signal (44.1kHz) output to external A/D converter 309 XBCK O Bit clock (2.8224 MHz) output to the external A/D converter 310 OSCI I Main system clock input terminal (22.5792 MHz) 311 OSCO O Main system clock output terminal (22.5792 MHz) 312 FS512 O Clock signal output for class-D amplifier Not used 313 DTCK I/O TSB master data clock input/output or SSB data input/output 314 UDP I/O USB data (+) input/output terminal 315 UDM I/O USB data (–) input/output terminal 316 USBHOLD I USB hold signal input terminal 317 SUSPEND O USB suspend signal output 318 UPUEN O USB pull-up resistor connection control output terminal 319 UOSCI I Resonator (48MHz) connection terminal for the USB oscillation circuit 320 UOSCO O Resonator (48MHz) connection terminal for the USB oscillation circuit 321 to 325 NC — Not used

are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. • Accessories are given in the last of the electrical parts list. NOTE: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) ↑ ↑ Parts Color Cabinet's Color Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 3-241-529-01 SCREW, STEP 2 3-266-200-01 SPRING (L), TORSION COIL 3 3-266-207-01 CAP (USB) 4 3-234-449-17 SCREW (M1.4) (NHF800) 4 3-234-449-19 SCREW (M1.4) (NH700) 5 3-266-208-01 LID, BATTERY CASE (for SILVER) (NH700) 5 3-266-208-11 LID, BATTERY CASE (for BLUE) (NH700) 5 3-266-208-31 LID, BATTERY CASE (NHF800) 6 3-266-206-01 KNOB (OPEN) (for SILVER) (NH700) 7-1. CASE (LOWER) SECTION 6 3-266-206-21 KNOB (OPEN) (for BLUE) (NH700) 6 3-266-206-41 KNOB (OPEN) (NHF800) 7 3-266-205-01 CASE (LOWER) (for SILVER) (NH700) 7 3-266-205-11 CASE (LOWER) (for BLUE) (NH700) 7 3-266-205-31 CASE (LOWER) (NHF800) 8 3-242-558-01 SPACER (LINE IN) 9 2-190-583-01 SPACER (BATT CASE) 10 2-190-583-11 SPACER (BATT CASE) 11 2-055-327-01 LEAF (LOWER), COPPER case (upper) section chassis section 1 2 3 4 4 4 5 6 7 8 11 9 10 • Abbreviation AUS : Australian model CH : Chinese model CND : Canadian model E15 : Iran model E18 : 100 V - 240 V AC area in E model E91 : 220 V area in E model EE : East Europian model HK : Hong Kong model Les composants identifiés par une marque 0 sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. JE : Tourist model KR : Korean model MX : Mexican model

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 X-2023-315-1 CASE (UPPER) (S) SUB ASSY (for SILVER) (NH700) 51 X-2023-316-1 CASE (UPPER) (L) SUB ASSY (for BLUE) (NH700) 51 X-2023-317-1 CASE (UPPER) (2BAND) SUB ASSY (NHF800: EXCEPT US) 51 X-2023-318-1 CASE (UPPER) (4BAND) SUB ASSY (NHF800: US) 52 3-249-687-41 KNOB (HOLD) (for SILVER) (NH700) 52 3-249-687-51 KNOB (HOLD) (for BLUE) (NH700) 52 3-249-687-71 KNOB (HOLD) (NHF800) 53 3-264-154-01 BADGE (HI-MD) 54 3-266-189-01 OPEN LOCKER 55 3-254-014-01 SCREW 56 3-266-190-01 BUTTON (CONTROL) (NAVI/−MENU. GROUP. x. X. T MARK/REC (+N)) 57 3-266-193-01 KNOB (ROTARY) 58 3-266-192-01 ESCUTCHEON (5 DIRECTION) (VOL +. >. VOL –. .) 59 3-266-191-01 KNOB (5 DIRECTION) (N ENT) 60 1-805-514-11 LCD MODULE 51 53 54 55 55 56 57 58 59 52 60 not supplied

102 3-266-197-01 OPEN SLIDER 103 3-266-196-01 CASE, BATTERY 104 3-266-194-01 MD STANDARD PIN 105 3-266-201-01 SPRING (R), EXTENSION 106 3-254-003-01 SCREW 107 3-266-199-01 SPRING (R), TORSION COIL 108 X-3385-056-1 CHASSIS ASSY, SET 109 3-246-996-01 SCREW (MD), STEP 110 X-2023-415-1 MAIN BOARD, COMPLETE (for SERVICE) (NH700: CND, MX, AUS) 110 X-2023-416-1 MAIN BOARD, COMPLETE (for SERVICE) (NH700: E18, E91, HK, KR, CH, JE) 110 X-2023-417-1 MAIN BOARD, COMPLETE (for SERVICE) (NH700: AEP, UK, EE) 110 X-2023-418-1 MAIN BOARD, COMPLETE (for SERVICE) (NHF800: US) 110 X-2023-419-1 MAIN BOARD, COMPLETE (for SERVICE) (NHF800: CND, AUS) 110 X-2023-420-1 MAIN BOARD, COMPLETE (for SERVICE) (NHF800: E15, HK) 110 X-2023-421-1 MAIN BOARD, COMPLETE (for SERVICE) (NHF800: AEP, UK, EE) 111 3-238-876-04 SCREW (M1.4), TOOTHED LOCK 112 3-266-204-01 TERMINAL (+), BATTERY 113 3-266-203-02 TERMINAL (–), BATTERY 114 2-148-293-01 SPRING (USB), LEAF 115 3-242-558-01 SPACER (LINE IN) 116 1-400-711-11 FILTER, EMI 117 2-178-287-01 SHEET (HP) 118 2-179-912-01 SHEET (CHASSIS) 119 2-177-905-01 SHEET (EMC H BRIDGE) 120 2-177-906-01 SHEET (EMC YUZU) 121 2-187-174-01 SHEET (EMC JACK) 122 2-179-913-01 SHEET (CASE BATTERY) 123 2-178-288-01 CUSHION (HP) 124 2-178-324-01 CUSHION (RODEO) 125 2-188-045-01 SHEET (EMC) mechanism deck section 101 102 103 104 105 106 107 108 122 123 109 117 118 118 118 118 MAIN board 111 112 113 120 124 125 121 111 114 116 115 119 110

mark 0 or dotted line with mark 0 are critical for safety. Replace only with part num- ber specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 7-4. MECHANISM DECK SECTION (MT-MZNH900-181) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 151 3-338-645-31 WASHER (0.8-2.5) 152 3-263-454-01 GEAR (BSA) 153 3-248-370-01 SCREW, SELF TAP 154 3-225-996-17 SCREW (M1.4) (EG), PRECISION PAN 155 3-244-880-01 SPRING, THRUST RETAINER 156 3-263-455-01 GEAR (SB) 157 3-259-972-22 CHASSIS (REC) 158 X-3384-651-2 BASE ASSY, MOTOR 159 X-3384-650-1 HOLDER ASSY 160 3-263-453-01 PLATE, RATCHET 161 X-2023-272-1 LEAD SCREW SERVICE ASSY 162 3-244-879-01 SPRING, RACK 0163 X-2021-785-1 OP SERVICE ASSY (ABX-U) (including HR601(OVER WRITE HEAD)) M701 8-835-782-12 MOTOR, DC SSM18D/C-NP (SPINDLE) M702 1-787-143-11 MOTOR, DC (SLED) M703 1-477-519-21 MOTOR UNIT, DC (OVER WRITE HEAD UP/DOWN) M701 M703 M702 151 152 153 154 154 157 160 161 158 159 162 153 155 156 153 163 (including HR601 (over write head) ) not supplied HR601 (over write head)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-2023-415-1 MAIN BOARD, COMPLETE (for SERVICE) (NH700: CND, MX, AUS) X-2023-416-1 MAIN BOARD, COMPLETE (for SERVICE) (NH700: E18, E91, HK, KR, CH, JE) X-2023-417-1 MAIN BOARD, COMPLETE (for SERVICE) (NH700: AEP, UK, EE) X-2023-418-1 MAIN BOARD, COMPLETE (for SERVICE) (US) X-2023-419-1 MAIN BOARD, COMPLETE (for SERVICE) (NHF800: CND, AUS) X-2023-420-1 MAIN BOARD, COMPLETE (for SERVICE) (NHF800: HK, E15) X-2023-421-1 MAIN BOARD, COMPLETE (for SERVICE) (NHF800: AEP, UK, EE) ********************* 1-400-711-11 FILTER, EMI 3-242-558-01 SPACER (LINE IN) 3-266-203-02 TERMINAL (-), BATTERY < CAPACITOR > C101 1-164-874-11 CERAMIC CHIP 100PF 5% 50V C102 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V C104 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V C105 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C106 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C107 1-131-862-11 TANTALUM CHIP 47uF 20% 4V C108 1-135-210-11 TANTALUM CHIP 4.7uF 20% 10V C151 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V C152 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V C153 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V (US) C153 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V (EXCEPT US) C154 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C160 1-137-859-11 TANTALUM CHIP 220uF 20% 4V C201 1-164-874-11 CERAMIC CHIP 100PF 5% 50V C202 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V C204 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V C205 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C206 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C207 1-131-862-11 TANTALUM CHIP 47uF 20% 4V C208 1-135-210-11 TANTALUM CHIP 4.7uF 20% 10V C251 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V C252 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V C253 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V (US) C253 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V (EXCEPT US) C254 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C260 1-137-859-11 TANTALUM CHIP 220uF 20% 4V C302 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V C303 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C304 1-164-874-11 CERAMIC CHIP 100PF 5% 50V C305 1-164-874-11 CERAMIC CHIP 100PF 5% 50V C306 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C308 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C310 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3V C311 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C312 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C313 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C314 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C315 1-165-851-91 TANTALUM CHIP 10uF 20% 6.3V C316 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V C318 1-135-149-21 TANTALUM CHIP 2.2uF 10% 10V C319 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C320 1-135-149-21 TANTALUM CHIP 2.2uF 10% 10V C321 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C322 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C323 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3V C324 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C325 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C327 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C328 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C351 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C352 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3V C353 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C354 1-135-151-21 TANTALUM CHIP 4.7uF 20% 4V C355 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V C356 1-135-201-11 TANTALUM CHIP 10uF 20% 4V C361 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C363 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C364 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C402 1-100-609-11 TANTALUM CHIP 220uF 5V C403 1-100-609-11 TANTALUM CHIP 220uF 5V C406 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C407 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C408 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C411 1-119-751-11 TANTALUM CHIP 22uF 20% 16V C412 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u: µ, for example: uA... : µA... uPA... : µPA... uPB... : µPB... uPC... : µPC... uPD... : µPD... • CAPACITORS uF: µF • COILS uH: µH • Abbreviation AUS : Australian model CH : Chinese model CND : Canadian model MAIN E15 : Iran model E18 : 100 V - 240 V AC area in E model E91 : 220 V area in E model EE : East Europian model HK : Hong Kong model JE : Tourist model KR : Korean model MX : Mexican model Les composants identifiés par une marque 0 sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board.

5V C424 1-100-609-11 TANTALUM CHIP 220uF 5V C425 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C426 1-119-751-11 TANTALUM CHIP 22uF 20% 16V C427 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C429 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C430 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C434 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C438 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C452 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C453 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C455 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V C456 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V C457 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C458 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C459 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C460 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C461 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C476 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C478 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C479 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C480 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V C481 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C511 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C513 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C515 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C516 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C517 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C518 1-135-210-11 TANTALUM CHIP 4.7uF 20% 10V C519 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C520 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C521 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V C522 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 50V C523 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C524 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C525 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V C526 1-164-874-11 CERAMIC CHIP 100PF 5% 50V C527 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C528 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C529 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C530 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C531 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C533 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C536 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V C537 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C538 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C539 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C545 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C547 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V C550 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V C552 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C553 1-135-210-11 TANTALUM CHIP 4.7uF 20% 10V C554 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C555 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V C556 1-135-210-11 TANTALUM CHIP 4.7uF 20% 10V C557 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C558 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C559 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V C560 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C561 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C562 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C564 1-135-210-11 TANTALUM CHIP 4.7uF 20% 10V C565 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C566 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C567 1-135-210-11 TANTALUM CHIP 4.7uF 20% 10V C568 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C569 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C570 1-165-847-91 TANTALUM CHIP 4.7uF 20% 10V C573 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C574 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C601 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C602 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C604 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C607 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C609 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C611 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C612 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V C613 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V C614 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V C616 1-165-897-11 TANTALUM CHIP 22uF 20% 10V C619 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C620 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V C621 1-135-201-11 TANTALUM CHIP 10uF 20% 4V C622 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C625 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C627 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C628 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C630 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C633 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C634 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C635 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C636 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C637 1-165-851-91 TANTALUM CHIP 10uF 20% 6.3V C638 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V C641 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C642 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V C643 1-100-743-91 CERAMIC CHIP 2.2uF 20% 16V C644 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V C645 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C646 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V C648 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V C649 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C650 1-165-851-91 TANTALUM CHIP 10uF 20% 6.3V C652 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3V C653 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3V C658 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C660 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C661 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V C666 1-127-820-11 CERAMIC CHIP 4.7uF 10% 16V C668 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V MAIN

33PF 5% 100V C675 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C676 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C677 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C701 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V C702 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V C703 1-119-923-11 CERAMIC CHIP 0.047uF 10% 10V C705 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C706 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V C707 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C708 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V C709 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C710 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V C712 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C713 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C714 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C715 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C716 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C717 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C801 1-164-847-11 CERAMIC CHIP 7PF 0.5PF 50V C802 1-164-847-11 CERAMIC CHIP 7PF 0.5PF 50V C803 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C804 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C805 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C808 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C809 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C810 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C811 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C812 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C814 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C816 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C817 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C818 1-165-851-91 TANTALUM CHIP 10uF 20% 6.3V C819 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C820 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C821 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C822 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C823 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C827 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C828 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C830 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C832 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C833 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C835 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C836 1-165-851-91 TANTALUM CHIP 10uF 20% 6.3V C838 1-165-851-91 TANTALUM CHIP 10uF 20% 6.3V C839 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C843 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C845 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C846 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C847 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C850 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C853 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C856 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C857 1-164-858-11 CERAMIC CHIP 22PF 5% 50V C858 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C859 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C860 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C861 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C864 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C883 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3V C884 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3V C885 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C886 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C887 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C891 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C892 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C895 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C901 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C902 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C903 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C906 1-100-352-11 CERAMIC CHIP 1uF 20% 16V C908 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C909 1-119-751-11 TANTALUM CHIP 22uF 20% 16V C915 1-165-851-91 TANTALUM CHIP 10uF 20% 6.3V C916 1-165-851-91 TANTALUM CHIP 10uF 20% 6.3V C918 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C919 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C920 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C922 1-128-964-11 TANTALUM CHIP 100uF 20% 6.3V C923 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C924 1-100-539-11 TANTALUM CHIP 47uF 20% 6.3V C926 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C927 1-164-874-11 CERAMIC CHIP 100PF 5% 50V C928 1-164-874-11 CERAMIC CHIP 100PF 5% 50V C929 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C931 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V C932 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C933 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V C935 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V C936 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V C937 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V C939 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V C940 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V C948 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V C954 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V C958 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C959 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C960 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C961 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < CONNECTOR > CN451 1-818-190-21 CONNECTOR, SQUARE TYPE (USB) 7P (USB) CN471 1-818-543-21 CONNECTOR, FFC/FPC (ZIF) 16P CN501 1-818-545-21 CONNECTOR, FFC/FPC (ZIF) 26P CN701 1-818-540-21 CONNECTOR, FFC/FPC (ZIF) 10P < DIODE > D151 8-719-056-72 DIODE UDZ-TE-17-2.4B D251 8-719-056-72 DIODE UDZ-TE-17-2.4B D301 8-719-056-54 DIODE MAZS068008SO D302 8-719-056-54 DIODE MAZS068008SO MAIN

F1 1-576-462-21 FUSE (SMD) (1.5A/63V) F351 1-576-439-21 FUSE (SMD) (0.25A/125V) < FERRITE BEAD/SHORT > FB1 1-400-808-21 INDUCTOR (EMI FERRITE) FB2 1-469-179-21 INDUCTOR, FERRITE BEAD FB101 1-500-284-21 INDUCTOR, FERRITE BEAD FB201 1-500-284-21 INDUCTOR, FERRITE BEAD FB301 1-216-864-11 SHORT CHIP 0 FB302 1-400-807-21 BEAD, FERRITE (1005) FB303 1-400-807-21 BEAD, FERRITE (1005) FB353 1-469-179-21 INDUCTOR, FERRITE BEAD FB354 1-469-179-21 INDUCTOR, FERRITE BEAD FB355 1-469-179-21 INDUCTOR, FERRITE BEAD FB357 1-400-808-21 INDUCTOR (EMI FERRITE) FB451 1-469-869-21 INDUCTOR (EMI FERRITE) (2012) FB452 1-469-869-21 INDUCTOR (EMI FERRITE) (2012) FB471 1-216-864-11 SHORT CHIP 0 FB501 1-400-620-21 INDUCTOR, FERRITE BEAD (1005) FB502 1-216-864-11 SHORT CHIP 0 FB503 1-216-864-11 SHORT CHIP 0 FB801 1-216-864-11 SHORT CHIP 0 FB802 1-216-864-11 SHORT CHIP 0 FB803 1-414-760-21 INDUCTOR, FERRITE BEAD FB807 1-216-864-11 SHORT CHIP 0 FB809 1-216-864-11 SHORT CHIP 0 FB810 1-414-760-21 INDUCTOR, FERRITE BEAD < IC > IC301 6-702-894-01 IC AK5356VN-L IC302 6-706-528-01 IC XC6219B212MR IC352 6-705-942-01 IC TA2131FLG (EL) IC401 6-705-536-01 IC MM1655NCBE IC402 6-706-652-01 IC NJU7008F3 (TE1) IC471 6-705-715-01 IC XC6219B242MR IC501 6-705-012-01 IC SN761059ZQLR IC502 6-706-095-01 IC R1180Q301B-TR-FA IC601 6-705-000-01 IC SC901585VAR2 IC602 6-703-317-01 IC R1160N121B-TR-FA * IC603 6-706-038-01 IC XC6209B322MR IC604 6-706-079-01 IC R1180Q121C-TR-FA IC605 6-706-214-01 IC TC7SL32FU (TE85R) IC606 6-702-590-01 IC XC61CN1702NR IC607 8-759-690-72 IC XC61CN0902NR IC701 6-704-999-01 IC BD6607KN IC801 8-753-229-55 IC CXD2681-223GG IC804 6-706-089-01 IC XC61CC2502NR IC881 6-759-639-21 IC XC6382C251MR IC882 6-706-094-01 IC R1180Q221B-TR-FA IC892 (Not supplied) IC HN58X2564FPIEZ IC901 6-704-997-01 IC SC901584EPR2 IC902 6-704-245-01 IC XC61CC1702NR < JACK > J301 1-815-950-12 JACK (LINE IN (OPT)) J302 1-794-084-12 JACK (MIC (PLUG IN POWER)) J352 1-816-954-22 JACK (i) J402 1-785-383-11 JACK, DC (POLARITY UNIFIED TYPE) (DC IN 3V) < COIL/SHORT > L303 1-400-397-11 INDUCTOR 10uH L351 1-216-295-00 SHORT CHIP 0 L501 1-216-295-00 SHORT CHIP 0 L502 1-400-397-11 INDUCTOR 10uH L503 1-400-397-11 INDUCTOR 10uH L504 1-400-397-11 INDUCTOR 10uH L505 1-400-397-11 INDUCTOR 10uH L506 1-400-397-11 INDUCTOR 10uH L507 1-400-397-11 INDUCTOR 10uH L601 1-414-398-11 INDUCTOR 10uH L603 1-414-398-11 INDUCTOR 10uH L605 1-416-669-11 INDUCTOR 22uH L606 1-400-626-11 INDUCTOR 10uH MAIN Ver 1.1

LF401 1-411-957-11 FILTER, COMMON MODE LF451 1-456-111-11 COIL, COMMON MODE CHOKE < TRANSISTOR > Q301 8-729-051-23 TRANSISTOR 2SA2018TL Q351 8-729-037-52 TRANSISTOR 2SD2216J-QR (TX).SO Q352 8-729-030-46 TRANSISTOR XP4314-TX Q353 6-550-353-01 FET SI1410EDH-T1 Q401 6-550-326-01 TRANSISTOR FZT968TA Q403 6-550-353-01 FET SI1410EDH-T1 Q406 8-729-427-74 TRANSISTOR XP4601 Q407 8-729-037-75 TRANSISTOR UN9214J-(TX).SO Q432 8-729-044-57 TRANSISTOR FZT688B-TP Q433 8-729-037-52 TRANSISTOR 2SD2216J-QR (TX).SO Q451 6-550-354-01 FET RTQ035P02TR Q452 8-729-427-74 TRANSISTOR XP4601 Q471 8-729-429-44 TRANSISTOR XP1501 Q501 6-550-674-01 FET MCH6604-K-TL-E Q502 8-729-051-23 TRANSISTOR 2SA2018TL Q503 8-729-037-52 TRANSISTOR 2SD2216J-QR (TX).SO Q504 8-729-037-89 TRANSISTOR 2SC4627J-C (TX).SO Q601 6-550-357-01 FET CPH5614-TL-E Q602 6-550-740-01 FET MCH6617-TL-E Q603 8-729-053-71 FET TS8K1TB Q607 8-729-037-52 TRANSISTOR 2SD2216J-QR (TX).SO Q608 8-729-030-46 TRANSISTOR XP4314-TX Q609 6-550-859-01 FET NTHD4508NT1G Q611 6-550-353-01 FET SI1410EDH-T1 Q612 8-729-049-81 FET SSM3K01F (TE85L) Q613 8-729-047-68 FET SSM3K03FE (TPL3) Q614 8-729-427-74 TRANSISTOR XP4601 Q615 6-550-353-01 FET SI1410EDH-T1 Q616 6-550-353-01 FET SI1410EDH-T1 Q617 8-729-427-74 TRANSISTOR XP4601 Q618 8-729-427-74 TRANSISTOR XP4601 Q801 8-729-047-68 FET SSM3K03FE (TPL3) Q802 8-729-051-50 FET XP152A12C0MR Q803 8-729-037-52 TRANSISTOR 2SD2216J-QR (TX).SO Q881 8-729-427-74 TRANSISTOR XP4601 Q883 8-729-037-75 TRANSISTOR UN9214J-(TX).SO Q884 8-729-030-46 TRANSISTOR XP4314-TX Q885 6-550-353-01 FET SI1410EDH-T1 Q886 8-729-030-46 TRANSISTOR XP4314-TX Q901 8-729-053-71 FET TS8K1TB Q902 8-729-427-74 TRANSISTOR XP4601 < RESISTOR > R101 1-208-927-11 METAL CHIP 47K 0.5% 1/16W R103 1-208-715-11 METAL CHIP 22K 0.5% 1/16W R105 1-218-990-11 SHORT CHIP 0 R106 1-208-911-11 METAL CHIP 10K 0.5% 1/16W R107 1-208-715-11 METAL CHIP 22K 0.5% 1/16W R151 1-218-961-11 RES-CHIP 4.7K 5% 1/16W (US) R151 1-218-965-11 RES-CHIP 10K 5% 1/16W (EXCEPT US) R152 1-218-957-11 RES-CHIP 2.2K 5% 1/16W (EXCEPT US) R152 1-218-961-11 RES-CHIP 4.7K 5% 1/16W (US) R153 1-218-965-11 RES-CHIP 10K 5% 1/16W R154 1-218-965-11 RES-CHIP 10K 5% 1/16W R155 1-218-929-11 RES-CHIP 10 5% 1/16W R156 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R157 1-208-683-11 METAL CHIP 1K 0.5% 1/16W R158 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16W R160 1-218-990-11 SHORT CHIP 0 (EXCEPT AEP, UK, EE) R160 1-208-635-11 METAL CHIP 10 0.5% 1/16W (AEP, UK, EE) R161 1-208-643-11 METAL CHIP 22 0.5% 1/16W (AEP, UK, EE) R162 1-218-990-11 SHORT CHIP 0 R201 1-208-927-11 METAL CHIP 47K 0.5% 1/16W R203 1-208-715-11 METAL CHIP 22K 0.5% 1/16W R205 1-218-990-11 SHORT CHIP 0 R206 1-208-911-11 METAL CHIP 10K 0.5% 1/16W R207 1-208-715-11 METAL CHIP 22K 0.5% 1/16W R251 1-218-961-11 RES-CHIP 4.7K 5% 1/16W (US) R251 1-218-965-11 RES-CHIP 10K 5% 1/16W (EXCEPT US) R252 1-218-957-11 RES-CHIP 2.2K 5% 1/16W (EXCEPT US) R252 1-218-961-11 RES-CHIP 4.7K 5% 1/16W (US) R253 1-218-965-11 RES-CHIP 10K 5% 1/16W R254 1-218-965-11 RES-CHIP 10K 5% 1/16W R255 1-218-929-11 RES-CHIP 10 5% 1/16W R256 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R257 1-208-683-11 METAL CHIP 1K 0.5% 1/16W R258 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16W R260 1-218-990-11 SHORT CHIP 0 (EXCEPT AEP, UK, EE) R260 1-208-635-11 METAL CHIP 10 0.5% 1/16W (AEP, UK, EE) R261 1-208-643-11 METAL CHIP 22 0.5% 1/16W (AEP, UK, EE) R262 1-218-990-11 SHORT CHIP 0 R301 1-218-953-11 RES-CHIP 1K 5% 1/16W R304 1-218-977-11 RES-CHIP 100K 5% 1/16W MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 56 MZ-NH700/NHF800 R305 1-218-941-11 RES-CHIP 100 5% 1/16W R306 1-218-965-11 RES-CHIP 10K 5% 1/16W R307 1-218-941-11 RES-CHIP 100 5% 1/16W R308 1-216-864-11 SHORT CHIP 0 R309 1-218-953-11 RES-CHIP 1K 5% 1/16W R310 1-218-953-11 RES-CHIP 1K 5% 1/16W R312 1-218-929-11 RES-CHIP 10 5% 1/16W R314 1-218-990-11 SHORT CHIP 0 R315 1-218-990-11 SHORT CHIP 0 R351 1-218-937-11 RES-CHIP 47 5% 1/16W R352 1-218-981-11 RES-CHIP 220K 5% 1/16W R353 1-218-969-11 RES-CHIP 22K 5% 1/16W R354 1-218-965-11 RES-CHIP 10K 5% 1/16W R355 1-218-989-11 RES-CHIP 1M 5% 1/16W R356 1-218-977-11 RES-CHIP 100K 5% 1/16W R358 1-220-804-11 RES-CHIP 2.2M 5% 1/16W R359 1-218-990-11 SHORT CHIP 0 R418 1-218-977-11 RES-CHIP 100K 5% 1/16W R419 1-218-965-11 RES-CHIP 10K 5% 1/16W R420 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R421 1-218-977-11 RES-CHIP 100K 5% 1/16W R422 1-218-989-11 RES-CHIP 1M 5% 1/16W R423 1-218-981-11 RES-CHIP 220K 5% 1/16W R424 1-218-985-11 RES-CHIP 470K 5% 1/16W R425 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R432 1-245-456-21 METAL CHIP 1 1% 1/5W R433 1-245-455-21 METAL CHIP 0.47 1% 1/5W R434 1-218-989-11 RES-CHIP 1M 5% 1/16W R435 1-218-990-11 SHORT CHIP 0 R436 1-218-981-11 RES-CHIP 220K 5% 1/16W R437 1-218-981-11 RES-CHIP 220K 5% 1/16W R438 1-218-977-11 RES-CHIP 100K 5% 1/16W R441 1-218-977-11 RES-CHIP 100K 5% 1/16W R442 1-218-977-11 RES-CHIP 100K 5% 1/16W R443 1-218-977-11 RES-CHIP 100K 5% 1/16W R444 1-218-977-11 RES-CHIP 100K 5% 1/16W R446 1-218-990-11 SHORT CHIP 0 R447 1-218-990-11 SHORT CHIP 0 R454 1-216-864-11 SHORT CHIP 0 R455 1-218-989-11 RES-CHIP 1M 5% 1/16W R456 1-218-985-11 RES-CHIP 470K 5% 1/16W R462 1-218-981-11 RES-CHIP 220K 5% 1/16W R463 1-218-945-11 RES-CHIP 220 5% 1/16W R464 1-208-935-11 METAL CHIP 100K 0.5% 1/16W R466 1-220-804-11 RES-CHIP 2.2M 5% 1/16W R467 1-218-965-11 RES-CHIP 10K 5% 1/16W R471 1-218-990-11 SHORT CHIP 0 R472 1-218-990-11 SHORT CHIP 0 R473 1-218-990-11 SHORT CHIP 0 R474 1-218-953-11 RES-CHIP 1K 5% 1/16W R475 1-218-990-11 SHORT CHIP 0 R476 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16W R477 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16W R478 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R480 1-218-977-11 RES-CHIP 100K 5% 1/16W R483 1-218-985-11 RES-CHIP 470K 5% 1/16W R484 1-218-981-11 RES-CHIP 220K 5% 1/16W R485 1-218-985-11 RES-CHIP 470K 5% 1/16W R486 1-218-990-11 SHORT CHIP 0 R489 1-218-941-11 RES-CHIP 100 5% 1/16W R490 1-218-941-11 RES-CHIP 100 5% 1/16W R491 1-218-941-11 RES-CHIP 100 5% 1/16W R501 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R502 1-218-953-11 RES-CHIP 1K 5% 1/16W R503 1-218-977-11 RES-CHIP 100K 5% 1/16W R504 1-218-977-11 RES-CHIP 100K 5% 1/16W R505 1-218-929-11 RES-CHIP 10 5% 1/16W R507 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R508 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R509 1-218-990-11 SHORT CHIP 0 R511 1-218-990-11 SHORT CHIP 0 R512 1-218-990-11 SHORT CHIP 0 R513 1-218-965-11 RES-CHIP 10K 5% 1/16W R514 1-218-973-11 RES-CHIP 47K 5% 1/16W R515 1-218-965-11 RES-CHIP 10K 5% 1/16W R516 1-218-973-11 RES-CHIP 47K 5% 1/16W R517 1-218-965-11 RES-CHIP 10K 5% 1/16W R518 1-218-973-11 RES-CHIP 47K 5% 1/16W R519 1-218-953-11 RES-CHIP 1K 5% 1/16W R520 1-218-949-11 RES-CHIP 470 5% 1/16W R521 1-218-990-11 SHORT CHIP 0 R522 1-218-990-11 SHORT CHIP 0 R524 1-218-945-11 RES-CHIP 220 5% 1/16W R525 1-216-864-11 SHORT CHIP 0 R526 1-216-864-11 SHORT CHIP 0 R561 1-218-981-11 RES-CHIP 220K 5% 1/16W R601 1-218-981-11 RES-CHIP 220K 5% 1/16W R605 1-218-953-11 RES-CHIP 1K 5% 1/16W R608 1-218-446-11 METAL CHIP 1 5% 1/10W R609 1-218-977-11 RES-CHIP 100K 5% 1/16W R612 1-220-804-11 RES-CHIP 2.2M 5% 1/16W R616 1-218-953-11 RES-CHIP 1K 5% 1/16W R617 1-218-953-11 RES-CHIP 1K 5% 1/16W R618 1-218-977-11 RES-CHIP 100K 5% 1/16W R619 1-218-977-11 RES-CHIP 100K 5% 1/16W R620 1-244-161-11 RES-CHIP 2.2 5% 1/16W R621 1-244-161-11 RES-CHIP 2.2 5% 1/16W R622 1-244-161-11 RES-CHIP 2.2 5% 1/16W R623 1-244-161-11 RES-CHIP 2.2 5% 1/16W R624 1-218-985-11 RES-CHIP 470K 5% 1/16W R625 1-218-985-11 RES-CHIP 470K 5% 1/16W R628 1-218-933-11 RES-CHIP 22 5% 1/16W R629 1-220-804-11 RES-CHIP 2.2M 5% 1/16W R635 1-216-864-11 SHORT CHIP 0 R636 1-218-985-11 RES-CHIP 470K 5% 1/16W R638 1-218-981-11 RES-CHIP 220K 5% 1/16W R639 1-218-989-11 RES-CHIP 1M 5% 1/16W R640 1-218-981-11 RES-CHIP 220K 5% 1/16W R641 1-218-989-11 RES-CHIP 1M 5% 1/16W R642 1-218-977-11 RES-CHIP 100K 5% 1/16W R643 1-218-990-11 SHORT CHIP 0 R645 1-218-985-11 RES-CHIP 470K 5% 1/16W R646 1-218-973-11 RES-CHIP 47K 5% 1/16W R647 1-218-989-11 RES-CHIP 1M 5% 1/16W R648 1-245-456-21 METAL CHIP 1 1% 1/5W MAIN Ver 1.1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 57 MZ-NH700/NHF800 R649 1-245-456-21 METAL CHIP 1 1% 1/5W R650 1-216-793-11 METAL CHIP 4.7 5% 1/10W R652 1-218-990-11 SHORT CHIP 0 R653 1-218-969-11 RES-CHIP 22K 5% 1/16W R654 1-218-989-11 RES-CHIP 1M 5% 1/16W R657 1-218-990-11 SHORT CHIP 0 R659 1-218-977-11 RES-CHIP 100K 5% 1/16W R660 1-218-985-11 RES-CHIP 470K 5% 1/16W R661 1-218-985-11 RES-CHIP 470K 5% 1/16W R662 1-218-985-11 RES-CHIP 470K 5% 1/16W R663 1-218-981-11 RES-CHIP 220K 5% 1/16W R664 1-216-789-11 METAL CHIP 2.2 5% 1/10W R665 1-218-990-11 SHORT CHIP 0 R668 1-216-864-11 SHORT CHIP 0 R670 1-218-990-11 SHORT CHIP 0 R671 1-218-990-11 SHORT CHIP 0 R673 1-218-990-11 SHORT CHIP 0 R675 1-220-804-11 RES-CHIP 2.2M 5% 1/16W R677 1-216-864-11 SHORT CHIP 0 R678 1-218-990-11 SHORT CHIP 0 R679 1-218-945-11 RES-CHIP 220 5% 1/16W R680 1-216-864-11 SHORT CHIP 0 R681 1-218-989-11 RES-CHIP 1M 5% 1/16W R682 1-218-989-11 RES-CHIP 1M 5% 1/16W R683 1-218-989-11 RES-CHIP 1M 5% 1/16W R684 1-218-965-11 RES-CHIP 10K 5% 1/16W R685 1-218-965-11 RES-CHIP 10K 5% 1/16W R706 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R707 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R708 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R709 1-218-965-11 RES-CHIP 10K 5% 1/16W R710 1-218-965-11 RES-CHIP 10K 5% 1/16W R711 1-218-965-11 RES-CHIP 10K 5% 1/16W R712 1-218-990-11 SHORT CHIP 0 R713 1-218-953-11 RES-CHIP 1K 5% 1/16W R801 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R802 1-218-990-11 SHORT CHIP 0 R804 1-218-933-11 RES-CHIP 22 5% 1/16W R805 1-218-933-11 RES-CHIP 22 5% 1/16W R806 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R807 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R808 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R809 1-218-990-11 SHORT CHIP 0 R810 1-218-990-11 SHORT CHIP 0 R811 1-218-965-11 RES-CHIP 10K 5% 1/16W R812 1-218-977-11 RES-CHIP 100K 5% 1/16W R813 1-218-945-11 RES-CHIP 220 5% 1/16W R815 1-218-981-11 RES-CHIP 220K 5% 1/16W R817 1-218-953-11 RES-CHIP 1K 5% 1/16W R818 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R819 1-218-953-11 RES-CHIP 1K 5% 1/16W R820 1-218-945-11 RES-CHIP 220 5% 1/16W R821 1-220-804-11 RES-CHIP 2.2M 5% 1/16W R822 1-218-989-11 RES-CHIP 1M 5% 1/16W R823 1-218-965-11 RES-CHIP 10K 5% 1/16W R824 1-218-990-11 SHORT CHIP 0 R825 1-218-990-11 SHORT CHIP 0 MAIN R826 1-218-990-11 SHORT CHIP 0 R827 1-218-941-11 RES-CHIP 100 5% 1/16W R829 1-218-990-11 SHORT CHIP 0 (NHF800) R830 1-218-990-11 SHORT CHIP 0 R832 1-218-965-11 RES-CHIP 10K 5% 1/16W R833 1-218-990-11 SHORT CHIP 0 R837 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R839 1-218-990-11 SHORT CHIP 0 R840 1-218-990-11 SHORT CHIP 0 R841 1-218-929-11 RES-CHIP 10 5% 1/16W R842 1-218-973-11 RES-CHIP 47K 5% 1/16W R843 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R845 1-216-864-11 SHORT CHIP 0 R855 1-218-990-11 SHORT CHIP 0 R856 1-218-990-11 SHORT CHIP 0 R857 1-218-985-11 RES-CHIP 470K 5% 1/16W R858 1-208-927-11 METAL CHIP 47K 0.5% 1/16W R860 1-218-929-11 RES-CHIP 10 5% 1/16W R861 1-218-933-11 RES-CHIP 22 5% 1/16W R862 1-218-989-11 RES-CHIP 1M 5% 1/16W R863 1-218-990-11 SHORT CHIP 0 R864 1-218-945-11 RES-CHIP 220 5% 1/16W R865 1-218-985-11 RES-CHIP 470K 5% 1/16W R866 1-218-990-11 SHORT CHIP 0 R867 1-218-989-11 RES-CHIP 1M 5% 1/16W R868 1-218-990-11 SHORT CHIP 0 R869 1-218-990-11 SHORT CHIP 0 R872 1-218-965-11 RES-CHIP 10K 5% 1/16W R873 1-218-965-11 RES-CHIP 10K 5% 1/16W R876 1-218-990-11 SHORT CHIP 0 R878 1-218-937-11 RES-CHIP 47 5% 1/16W R879 1-218-937-11 RES-CHIP 47 5% 1/16W R880 1-218-937-11 RES-CHIP 47 5% 1/16W R881 1-218-981-11 RES-CHIP 220K 5% 1/16W R882 1-218-985-11 RES-CHIP 470K 5% 1/16W R883 1-218-989-11 RES-CHIP 1M 5% 1/16W R884 1-218-985-11 RES-CHIP 470K 5% 1/16W R885 1-218-989-11 RES-CHIP 1M 5% 1/16W R886 1-218-977-11 RES-CHIP 100K 5% 1/16W R887 1-218-977-11 RES-CHIP 100K 5% 1/16W R888 1-218-981-11 RES-CHIP 220K 5% 1/16W R889 1-218-973-11 RES-CHIP 47K 5% 1/16W R890 1-218-981-11 RES-CHIP 220K 5% 1/16W R891 1-218-990-11 SHORT CHIP 0 R892 1-218-981-11 RES-CHIP 220K 5% 1/16W R893 1-220-804-11 RES-CHIP 2.2M 5% 1/16W R894 1-218-977-11 RES-CHIP 100K 5% 1/16W R895 1-218-977-11 RES-CHIP 100K 5% 1/16W R897 1-218-990-11 SHORT CHIP 0 R903 1-218-989-11 RES-CHIP 1M 5% 1/16W R904 1-218-989-11 RES-CHIP 1M 5% 1/16W R906 1-218-973-11 RES-CHIP 47K 5% 1/16W R907 1-218-965-11 RES-CHIP 10K 5% 1/16W R908 1-218-969-11 RES-CHIP 22K 5% 1/16W R910 1-218-969-11 RES-CHIP 22K 5% 1/16W R912 1-218-981-11 RES-CHIP 220K 5% 1/16W R914 1-208-911-11 METAL CHIP 10K 0.5% 1/16W R917 1-218-981-11 RES-CHIP 220K 5% 1/16W Ver 1.1

S892 1-771-339-41 SWITCH, PUSH (HALF LOCK) S893 1-762-805-21 SWITCH, PUSH (1 KEY) (OPEN/COLSE DETECT) S894 1-786-703-21 SWITCH, PUSH (2 KEY) (PROTECT DETECT, Hi-MD PROTECT DETECT) < THERMISTOR (POSITIVE) > THP401 1-805-580-11 THERMISTOR, POSITIVE < VARISTOR > VDR801 1-805-697-21 VARISTOR (SMD) < VIBRATOR > X801 1-813-353-21 VIBRATOR, CERAMIC (48MHz) X802 1-813-314-11 VIBRATOR, CRYSTAL (22.5792MHz) ************************************************************* MISCELLANEOUS ************** 60 1-805-514-11 LCD MODULE 0163 X-2021-785-1 OP SERVICE ASSY (ABX-U) (including HR601 (OVER WRITE HEAD) ) M701 8-835-782-12 MOTOR, DC SSM18D/C-NP (SPINDLE) M702 1-787-143-11 MOTOR, DC (SLED) M703 1-477-519-21 MOTOR UNIT, DC (OVER WRITE HEAD UP/DOWN) ************************************************************** MAIN The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. ACCESSORIES ************ 1-543-793-41 FILTER, CLAMP (FERRITE CORE) (for Optional Stereo Microphone) 1-543-798-31 FILTER, CLAMP (FERRITE CORE) (for Optional Line Cable) 0 1-569-007-12 ADAPTOR, CONVERSION 2P (NH700: JE) 1-816-206-11 CONNECTOR, LIGHT (NH700: AEP, UK, E18, E91, EE, AUS/ NHF800: AEP, UK, E15, EE, AUS) 1-816-206-21 CONNECTOR, LIGHT (NH700: HK, KR, CH, JE/ NHF800: HK) 3-220-749-01 CASE, CARRYING (EXCEPT NHF800: US) 3-223-571-01 CASE, BATTERY CARRYING (EXCEPT NHF800: US) 3-266-457-11 MANUAL, INSTRUCTION (CZECH) (NH700: EE) 3-266-457-21 MANUAL, INSTRUCTION (HUNGARIAN) (NH700: EE) 3-266-457-31 MANUAL, INSTRUCTION (POLISH) (NH700: EE) 3-266-457-41 MANUAL, INSTRUCTION (SLOVAKIAN) (NH700: EE) 3-266-457-51 MANUAL, INSTRUCTION (RUSSIAN) (NH700: EE) 3-266-457-61 MANUAL, INSTRUCTION (TRADITIONAL CHINESE) (NH700: E18, HK) 3-266-457-71 MANUAL, INSTRUCTION (ENGLISH) (NH700: CH, JE) 3-266-457-81 MANUAL, INSTRUCTION (SIMPLIFIED CHINESE) (NH700: CH, JE) 3-266-457-91 MANUAL, INSTRUCTION (KOREAN) (NH700: KR) 3-266-469-11 MANUAL, INSTRUCTION (ENGLISH) (NH700: CND, AEP, UK, E18, EE, HK, AUS) 3-266-469-21 MANUAL, INSTRUCTION (FRENCH) (NH700: CND, AEP) 3-266-469-31 MANUAL, INSTRUCTION (GERMAN) (NH700: AEP) 3-266-469-41 MANUAL, INSTRUCTION (SPANISH) (NH700: AEP, E91, MX) 3-266-469-51 MANUAL, INSTRUCTION (DUTCH) (NH700: AEP) 3-266-469-61 MANUAL, INSTRUCTION (SWEDISH) (NH700: AEP) 3-266-469-71 MANUAL, INSTRUCTION (ITALIAN) (NH700: AEP) 3-266-469-81 MANUAL, INSTRUCTION (PORTUGUESE) (NH700: AEP) 3-266-469-91 MANUAL, INSTRUCTION (FINNISH) (NH700: AEP) 3-266-529-11 MANUAL, INSTRUCTION (ENGLISH) (NHF800: CND) 3-266-529-21 MANUAL, INSTRUCTION (FRENCH) (NHF800: CND) 3-266-529-31 MANUAL, INSTRUCTION (ENGLISH) (NHF800: AEP, UK, E15, EE, HK, AUS) 3-266-529-41 MANUAL, INSTRUCTION (FRENCH) (NHF800: AEP) 3-266-529-51 MANUAL, INSTRUCTION (GERMAN) (NHF800: AEP) 3-266-529-61 MANUAL, INSTRUCTION (SPANISH) (NHF800: AEP)

(NHF800: AEP) 3-266-529-81 MANUAL, INSTRUCTION (SWEDISH) (NHF800: AEP) 3-266-529-91 MANUAL, INSTRUCTION (ITALIAN) (NHF800: AEP) 3-266-571-11 MANUAL, INSTRUCTION (PORTUGUESE) (NHF800: AEP) 3-266-571-21 MANUAL, INSTRUCTION (FINNISH) (NHF800: AEP) 3-266-571-31 MANUAL, INSTRUCTION (CZECH) (NHF800: EE) 3-266-571-41 MANUAL, INSTRUCTION (HUNGARIAN) (NHF800: EE) 3-266-571-51 MANUAL, INSTRUCTION (POLISH) (NHF800: EE) 3-266-571-61 MANUAL, INSTRUCTION (SLOVAKIAN) (NHF800: EE) 3-266-571-71 MANUAL, INSTRUCTION (RUSSIAN) (NHF800: EE) 3-266-571-81 MANUAL, INSTRUCTION (TRADITIONAL CHINESE) (NHF800: E15, HK) 3-266-571-91 MANUAL, INSTRUCTION (ENGLISH) (NHF800: US) X-2022-247-4 CD-ROM (APPLICATION) ASSY (NH700: CND/NHF800: US, CND) X-2022-248-3 CD-ROM (APPLICATION) ASSY (NH700: AEP, UK, EE/NHF800: AEP, UK, EE) X-2023-448-1 CD-ROM (APPLICATION) ASSY (NH700: E18, HK, KR, AUS, CH/ NHF800: E15, HK, AUS) X-2023-449-1 CD-ROM (APPLICATION) ASSY (NH700: E91, MX) X-2023-450-1 CD-ROM (APPLICATION) ASSY (NH700: JE) 501 8-954-007-91 RECEIVER, EAR MDR-027SP/1 SET (NHF800: US) 502 8-954-008-90 RECEIVER, EAR MDR-E808SP/C SET (EXCEPT NHF800: US) 503 1-477-548-13 REMOTE CONTROL UNIT (RM-MC21) (NH700: EXCEPT CH, JE) 503 1-478-468-21 REMOTE COMMANDER (RM-MC40ELK) (NH700: CH, JE) 503 A-3172-189-A REMOTE CONTROL UNIT (RM-MC39LT) (NHF800: US) 503 A-3172-190-A REMOTE CONTROL UNIT (RM-MC39LT) (NHF800: CND) 503 A-3172-191-A REMOTE CONTROL UNIT (RM-MC39LT) (NHF800: AEP, UK, EE) 503 A-3172-192-A REMOTE CONTROL UNIT (RM-MC39LT) (NHF800: E15, HK, AUS) 504 1-543-793-41 FILTER, CLAMP (FERRITE CORE) 505 1-543-798-31 FILTER, CLAMP (FERRITE CORE) 506 1-823-519-61 CORD, CONNECTION (DEDICATED USB CABLE) 0507 1-477-965-21 ADAPTOR, AC (AC-ES3010K) (NH700: JE) 0507 1-478-423-21 ADAPTOR, AC (AC-ES3010K) (NH700: KR) 0507 1-478-424-21 ADAPTOR, AC (AC-ES3010K) (NH700: CH) 0507 1-478-425-41 ADAPTOR, AC (AC-ES3010K) (NH700: AEP, EE, E18, E91) 0507 1-478-426-51 ADAPTOR, AC (AC-ES3010K) (NH700: UK, HK) 0507 1-478-427-31 ADAPTOR, AC (AC-ES3010K) (NH700: CND,MX) 0507 1-478-428-21 ADAPTOR, AC (AC-ES3010K) (NH700: AUS) 0508 1-478-371-11 ADAPTOR, AC (AC-ET307K) (NHF800: US, CND) 0508 1-478-372-11 ADAPTOR, AC (AC-ET307K) (NHF800: AEP, EE) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. Headphones (MDR-027SP) (1) (US model) 501 Headphones/earphones (MDR-E808SP) (1) (EXCEPT US model) 502 Clamp filter (Ferrite core) (Small) (1) 504 Clamp filter (Ferrite core) (Small) (1) 504 Remote control (1) (RM-MC21 (NH700: EXCEPT CH, JE)) (RM-MC40ELK (NH700: CH, JE)) (RM-MC39LT (NHF800)) (RM-MC21, RM-MC40ELK) (RM-MC39LT) 503 506 Clamp filter (Ferrite core) (Lage) (2) 505 Clamp filter (Ferrite core) (Small) (1) 504 Dedicated USB cable (1) 507 Clamp filter (Ferrite core) (Small) (2) 504 AC power adaptor (AC-ES3010K) (1) AC power adaptor (AC-ET307K) (1) 508 Clamp filter (Ferrite core) (Large) (1) 505 Clamp filter (Ferrite core) (Small) (2) 504 NH-7WMAA Nickel metal hydride rechargeable battery (1) 509 0508 1-478-373-11 ADAPTOR, AC (AC-ET307K) (NHF800: UK, HK) 0508 1-478-374-11 ADAPTOR, AC (AC-ET307K) (NHF800: AUS) 0508 1-478-377-11 ADAPTOR, AC (AC-ET307K) (NHF800: E15) 509 1-756-317-22 BATTERY, NICKEL HYDROGEN (NH-7WMAA) (EXCEPT NH700: CND/NHF800: US, CND) Ver 1.1

Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 1.0 2004.07 New 1.1 2004.09 Change of all contents Test Mode and Electrical Adjustments Change of Part No. for IC801, R312, R860 on the MAIN board and AC Adaptor Addition of “Position of Ferrite Core” in the Disassembly (ECN-ECA12671/ECA30140/ECA37792/ECA40256)