ParaBody 813102 Assembly Instructions Manual

Please note: * Thank you for purchasing the Parabody 813102 VKRJCHIN/DIP. Please read these instructions thoroughly and keep them for future reference. This product must be assembled ¯ on a flat, level surface toassure its proper function.. * We recommendcleaning your product (pads and frame) oI~ a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these rules: 1. Inspect equipment daily. Tighten all loose connections and. replace worn parts immediately. Failure to do so may result in serious injury. 2. Do not allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. ! Tools Required for Assembly] * 9/16" wrench * Ratchet with 9/16" socket * Adjustable wrench * Hammer * Tape measure Bolt Length Ruler I NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSI~E OF THE HEAD OF THE BOLT. BOLT LENGTH RULER: BOLT LENGTH 3 4 5 6 0 1 2 I , I I I [ I ,

8 3102601 3/8" LOCK WASHER 1 2 34 6 PART# 2 9 3102802 1 10 3102904 2 11 3103101 12 3103103 "13 14 15 6236701 6405201 6467001 DESCR1FHON 3/8" LOCK NUT 14 3/8 X 3" BOLT 20 1-1/4X5" GRIP 2 1-1/4X7’ ChTdP 6 1-3/4" SQ. END CAP 1 2" SQ. END CAP 4 2" SQ. COVER CAP 4 FIGURE 1 STEP 1: ¯ Insert four 2" SQ. COVER CAPS (15) into the ends of the VKR SIDES (3) as shown in FIGURE ¯ Insert four 2" SQ. END CAPS (14) into the the ends of the VKR SIDES (3) as shown in FIGURE 3

(4) to the VKR SIDES’, (3) using two 3/8 X 3" BOLTS (10), four 3/8" FLAT WASHERS (7), and two 3/8" LOCK NUTS (9) as shown in FIGURE ¯ LOOSELY assemble the two BASE CONNECTORS (1) to the VKR SIDE~g (3) using eight 3/8 X 3" BOLTS (10), sixteen 3/8" FLAT WASHERS (7), and eight 3/8" LOCK NUTS (9) as shown in FIGURE ¯ Insert one 2" SQ END CAP (14) into the the end of the UPPER BACK SU-PPORT (4) as shown in FIGURE I 1/2 [ 1,2 [ 1/2 [ 1/2 I 1/2 I 1/2 I 0 1 2 3 4 5 6 4

WASHERS (7), and two 3/8" LOCK NUTS. ¯ SECURELY tigten all connections made up to this point.

PADS (6) to the VKR SIDES (3) using four 3/8 X 3" BOLTS (10), four 3/8" WASHERS (8), and four 3/8" FLAT WASHERS (7) as shown in FIGURE 4. (NOTE: Place the high side of A1LM PAD toward the outside.) 1/2 I 1/2 I 1/2 I 1/2 I 1/2 ] 1/2 I 1 2 3 4 5 6

FIGURE 5 STEP 5: ¯ SECURELY assemble the BACK PAD (5) to the UPPER BACK SUPPOI~.T (4) using two 3/8 X 3" BOLTS (1 two 3/8" LOCK WASHEP~S (8), two 3/8" FLAT WASHERS (7) as shown in FIGUR~

(12) over the HANDLES of the VKR SIDES (4) and the CHIN BAR (2) as in FIGURE 6. ¯ Slide two 1-1/4 X 5" HANDLES (11) over the ARM PAD HANDLE S ofthe VKR S IDES (4) as shown FIGURE 6. (NOTE: Rubbing alcohol can be used on the inside of the grips to make them slide on easier.) Thank you for purchasing the Parabody 884101 SAFTEY RAIL ATTACI~IENT. If unsure ofproper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. 0 1 2 3 4 5 6 $