Peripheral Electronics IS77 Owner's Manual

13160 56th Court Clearwater, Florida 33760 Ph. 866-788-4237 [email protected] ©2007 AAMP of Florida, Inc. Owner’s Manual Media Gateway PXAMG Expand Your Factory Radio to your car’s FM stereo iPod ® MP3 Players other audio sources Peripheral Electronics®, a division of AAMP of America™ 13160 56th Court Clearwater, Florida 33760 Ph. 800-477-2267 ext. 230 [email protected] ©2009 AAMP of Florida, Inc. Rev. 10-28-08 Universal Owner’s Manual IS77 Factory Radio Aftermarket Radio For OR

Pages 1. Introduction 1 2. IS77 Components 1 3. Installation Options 1 4. Radio Input Interface (PURI) Installarion 2 5. Troubleshooting 4 6. Warranty Information 5

provide the connecting link between your audio source and your FM radio. Using the supplied accessories, you can connect virtually any audio source into any FM equipped radio. This interface has a universal input that can be configured to accept an audio signal from any source with an RCA connection or a standard 3.5mm “Headphone” output. The IS77 will route the audio from your device through your factory or aftermarket radio not equipped with a built in auxiliary input. If your audio source is an iPod featuring a docking connector, this interface will also charge the iPod’s battery, when connected. 2. IS77 Components • One Radio Input Interface • One 3.5 mm to 3.5 mm Audio Cable (4ft.) • One 3.5mm to RCA adapter • One Power Cable with a On/Off Switch • One iPod Audio/Video Cable Outputs (5ft.) • One “factory look” 3.5mm Dash/Panel Mount Audio Input Cable (6ft.) 3. Installation Options (Choose A or B) A. Connecting an iPod iPod Specific installation instructions 1) Connect the two audio connectors from the iPod cable to the audio inputs on the PURI. 2) Connect the two-pin power connector on the iPod cable to the connector labeled “Connect to iPod” in the PURI wiring harness. 3) The Yellow connector from the iPod cable is intended for video playback from iPods that support this function. Route this Video connection to any video display that is not in view of the driver while operating the automobile. 4) Route the iPod connector to your chosen iPod location in your automobile. Common locations are the glove box, center console or in a mounted iPod cradle. You will need to access the iPod in order to change music selections, etc.. Antenna Out* Antenna In * PURI Connects to iPod Connects to On/OffSwitch MENU 3. Connecting a source with RCA outputs iPodAudio Cable (5 ft.) Fuse Fuse 3.5 mm to RCA Adapter Antenna Out* Antenna In * PURI Connects to On/OffSwitch Fuse 3.5 mm to 3.5 mm Audio Cable (4 ft.) “factory look” 3.5 mm Dash/Panel Mount Audio Input Cable (6 ft.) 3/8” hole C MP3 (not included) iPod (not included) Connect To SWITCH Connect To iPod Connect To SWITCH iPod Conection Not USE Connect To iPod Conection audio source (not included) OR

Installing the 3.5 Dash Panel Mount Audio Input Antenna In * PURI MENU 3. Connecting a source with RCA outputs iPodAudio Cable (5 ft.) 3.5 mm to RCA Adapter Antenna Out* Antenna In * PURI Connects to On/OffSwitch Fuse 3.5 mm to 3.5 mm Audio Cable (4 ft.) “factory look” 3.5 mm Dash/Panel Mount Audio Input Cable (6 ft.) 3/8” hole RCA to RCA (not included) Antenna Out* Antenna In * PURI Connects to On/OffSwitch Fuse audio source (not included) MP3 (not included) * Some radios require the addition of antenna connection adapters Connect To SWITCH iPod Conection Not USE Connect To SWITCH iPod Conection Not USE audio source (not included) OR 1) Choose mounting position of dash mount audio input and carefully drill 3/8” mounting hole. Install connector. 2) Connect your audio device to the newly installed audio input via the supplied 3.5 mm to 3.5 mm connection cable. 3.5 mm to 3.5 mm Audio Cable (4 ft.) “factory look” 3.5 mm Dash Panel Mount Audio input (6 ft.) 3/8” 4. Radio Input Interface (PURI) Installation PURI Universal Radio Input Stereo Audio to FM Radio Audio Input  ° L ° R Power 12V DC ° Ground °  Antenna Input ° Antenna Output ° Tuning Frequency (MHz FM)  87.9 88.3 Radio Tuning Frequency Use to select best operating frequency for your area Audio Input Left & Right Antenna Out to FM radio* Antenna Input from vehicle antenna* Ground Connection Connect to a clean ground point Factory or Upgraded Radio* On/Off Switch 3/4” mounting hole Connects to Power Source ACC 12VDC Power when key-on 2A Fuse TOP VIEW Gain Adjustment Use to match volume of PURI to volume of FM radio stations BACK VIEW H L LEVEL + * Antenna Adapter May be Required

1) The PURI is designed to install Inline with the radio antenna connection usually located on the back of the radio in the dash. In some cases this connection may be at a remote radio tuner location. Consult vehicle manufacturer’s information in these cases. 2) Some antenna connections require the use of an antenna adapter in order to connect to the PURI. These adapters are available from most car audio installation retailers. 3) Select the FM frequency where you will access your new audio device. On the side of PURI where the label indicates “Tuning Frequency” there is a two position switch. Note the position of the switch before installing the interface. If you have a local radio station that occupies either of these frequencies (87.9 or 88.3) please move the switch to the position that does NOT match the local station. The position of this switch determines the frequency where you will access your new audio input. We recommend choosing one option, and setting one of the radio’s preset buttons to represent that station. This easily accesses your auxiliary audio input by pressing the preset button. Using a Multimeter, identify 12V+ and Ground wires behind the radio. a. Connect the PURI Red wire to 12V+ (Ignition) b. Connect the PURI Black wire to Ground c. Connect the vehicle’s antenna into the PURI antenna input* d. Connect the PURI antenna output into the radio* *A vehicle specific antenna adaptor may be required to make these connections The rocker switch supplied with the PURI will turn the device on and off. When the switch is in the on position, the PURI will interrupt the incoming antenna signal to deliver the cleanest signal possible from your device through your FM radio. To regain standard FM reception, move the switch to the Off position. 4) Once the PURI is installed correctly, be sure to properly set the audio level. When set correctly, the audio level of the PURI will match the volume of typical FM radio stations. O /O S tc 3/4” mounting hole Connects to Power Source ACC 12VDC Power when key-on 2A Fuse Gain Adjustment Use to match volume of PURI to volume of FM radio stations BACK VIEW H L LEVEL +

Aux source 1) IS77 is turned off Move rocker switch to ON position 2) Connection cables are discon- nected Check all interconnects for proper con- nection 3) The radio is not on the correct station Verify that the FM radio is tuned to the frequency on the side of the interface. iPod does not charge 1) The power connection on the IS77 is disconnected Connect power cable according to Con- figuration 1 in Section 3 2) The fuse may be blown in the power plug on the iPod specific connection cable If fuse is blown, replace with equivalent fuse Noise / Static 1) Improper selection of IS77 frequency Tune to the frequency specified on the side of the IS77 interface. 2) local radio station is interfering with the Auxiliary input device Change the frequency setting on the side of the IS77 to the other position, and use the new frequency to access the audio source Low audio 1) the volume is down on the audio source Turn up the volume on the source to en- sure best sound quality through the IS77 The IS77 Gain is set too low Adjust the gain setting on the back side of the IS77 iPod is a trademark of Apple Inc., registered in the U.S. and other countries. iPhone is a trademark of Apple Inc. For Best Performance Have It Professionally Installed.

One Year Limited Warranty The quality controls used in the manufacture of this product will ensure your satisfaction. This warranty applies only to the original purchaser of this product from an authorized Peripheral Electronics dealer. This warranty covers any supplied or manufactured parts of this product that, upon inspection by Peripheral Electronics authorized personnel, is found to have failed in normal use due to defects in material or workmanship. This warranty does not apply to installation expenses. Attempting to service or modify this unit, operating this unit under conditions other than the recommended voltage will render this WARRANTY VOID. Unless otherwise prescribed by law, Peripheral Electronics shall not be liable for any per- sonal injury, property damage and or any incidental or consequential damages of any kind (including water damage) resulting from malfunctions, defects, misuse, improper installation or alteration of this product. All parts of this Peripheral Electronics product are guaranteed for a period of 1 year as follows: Within the first 12 months from date of purchase, subject to the conditions above, Peripheral Electronics will repair or replace the product at their discretion, if it is defective in material or workmanship providing it is returned to an Authorized Peripheral Electronics’ dealer, with PROOF OF PURCHASE from an authorized Peripheral Electronics dealer. Warning: This equipment may be reset by unintentional electrostatic discharge during operation. Exposure to direct sunlight or extreme heat may cause damage or malfunction. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener- ates, uses, and can radiate radio frequency energy and, if not installed and used in accor- dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Re-orientate or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that of which the receiver is connected. 4. Consult the dealer or an experienced radio / television technical for help. Notice : The changes or modifications not expressly approved by the party responsible com- pliance could void the user authority to operate the equipment.

13160 56th Court Clearwater, Florida 33760 Ph. 800-477-2267 ext. 230 [email protected] ©2009 AAMP of Florida, Inc.