Sony HCD-ZX80D Service Manual

US Model HCD-ZX80D E Model HCD-ZX80D/ZX100D HCD-ZX80D/ZX100D Ver. 1.2 2007.08 SPECIFICATIONS 9-887-251-03 2007H05-1 © 2007.08 Sony Corporation Personal Audio Division Published by Sony Techno Create Corporation • HCD-ZX80D is the amplifier, disc player, tape deck and tuner section in FST-ZX80D/LBT-ZX80D. • HCD-ZX100D is the amplifier, disc player, tape deck and tuner section in FST-ZX100D/LBT-ZX100D. DVD Model Name Using Similar Mechanism NEW Section DVD Mechanism Type CDM74HF-DVBU101 Optical Pick-up Block Name KHM-310CAB or KHM-313CAB Tape deck Model Name Using Similar Mechanism NEW Section Tape Transport Mechanism Type CWN42RR603 – Continued on next page – Photo: HCD-ZX80D This system incorporates Dolby* Digital, Dolby Pro Logic (II) adaptive matrix surround decoder, and the DTS** Digital Surround System. * Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories. **Manufactured under license from Digital Theater Systems, Inc. “DTS” and “ DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc. Amplifier section HCD-ZX100D The following are measured at AC 120, 127, 220, 240V 50/60 Hz DIN power output (rated): 130 W + 130 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) Front speaker: 170 W + 170 W (6 ohms at 1 kHz, 10% THD) Center speaker: 80 W (16 ohms at 1 kHz, 10% THD) Surround speaker: 170 W + 170 W (6 ohms at 1 kHz, 10% THD) Subwoofer: 180 W (8 ohms at 100 Hz, 10% THD) HCD-ZX80D The following are measured at AC 120, 127, 220, 240V 50/60 Hz DIN power output (rated):155 W + 155 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) Front speaker: 200 W + 200 W (6 ohms at 1 kHz, 10% THD) Center speaker: 80 W (16 ohms at 1 kHz, 10% THD) Surround speaker: 200 W + 200 W (6 ohms at 1 kHz, 10% THD) Inputs VIDEO INPUT (phono jacks): VIDEO: 1 Vp-p, 75 ohms AUDIO L/R: Voltage 250 mV, impedance 47 kilohms TV/SAT AUDIO IN L/R (phono jacks): Voltage 250 mV/450 mV, impedance 47 kilohms MIC 1 or 2 (phone jack): Sensitivity 1 mV, impedance 10 kilohms Outputs AUDIO OUT (phono jacks): Voltage 250 mV, impedance 1 kilohm VIDEO OUT (phono jack): Max. output level 1 Vp-p, unbalanced, Sync. negative load impedance 75 ohms COMPONENT VIDEO OUT: Y: 1 Vp-p, 75 ohms PB/CB: 0.7 Vp-p, 75 ohms PR/CR: 0.7 Vp-p, 75 ohms AUDIO POWER SPECIFICATION (HCD-ZX80D USA model only) POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6-ohm loads, both channels driven, from 120 Hz − 10 kHz; rates 160 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output. Continuous RMS power output (reference) Front speaker: 200 W + 200 W (6 ohms at 1 kHz, 10% THD) Center speaker: 80 W (16 ohms at 1 kHz, 10% THD) Surround speaker: 200 W + 200 W (6 ohms at 1 kHz, 10% THD)

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range 87.5 − 108.0 MHz (50 kHz step) Antenna FM lead antenna Antenna terminals 75 ohms unbalanced Intermediate frequency 10.7 MHz AM tuner section Tuning range Pan American models: 530 − 1,710 kHz (with the interval set at 10 kHz) 531 − 1,710 kHz (with the interval set at 9 kHz) Other models: 531 − 1,602 kHz (with the interval set at 9 kHz) 530 − 1,710 kHz (with the interval set at 10 kHz) Antenna AM loop antenna Antenna terminals External antenna terminal Intermediate frequency 450 kHz General Power requirements Mexican model: 127 V AC, 60 Hz US model: 120 V AC, 60 Hz Other models: 120 V, 220 V or 230 − 240 V AC, 50/60 Hz Adjustable with voltage selector Power consumption HCD-ZX100D 430 W HCD-ZX80D 390 W Dimensions (w/h/d) (Approx.) 281 × 379 × 404.5 mm (11 1/8 × 15 × 16 in.) Mass (Approx.) 16.3 kg (35 lb 15 oz) Design and specifications are subject to change without notice. Frequency response DVD (PCM 48 kHz): 2 Hz − 22 kHz (±1dB) CD: 2 Hz − 20 kHz (±0.5 dB) Video color system format Pan American models: NTSC Other models: NTSC and PAL Tape deck section Recording system 4-track 2-channel stereo Frequency response 50 − 13,000 Hz (±3 dB), using Sony TYPE I tape Disc player section System Compact disc and digital audio and video system Laser Semiconductor laser (DVD: λ = 650 nm, CD: λ = 790 nm) Emission duration: continuous CENTER SPEAKER: Use only the supplied speaker SUBWOOFER OUT: HCD-ZX100D: Use only the supplied subwoofer HCD-ZX80D (phono jacks): Voltage 250 mV, impedance 1 kilohm SURR SPEAKER: Use only the supplied speakers PHONES (stereo mini jack): accepts headphones of 8 ohms or more FRONT SPEAKER: Use only the supplied speakers S VIDEO OUT (4-pin/mini-DIN jack): Y: 1 Vp-p, unbalanced, Sync. negative C: 0.286 Vp-p, load impedance 75 ohms Ver. 1.1

• Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 ˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. SELF DIAGNOSIS FUNCTION (When letters/numbers appear in the display) When the self-diagnosis function is activated to prevent the system from malfunctioning, a 5-character service number (e.g. C 13 50) with a combination of a letter and 4 digits appears on the TV screen and the front panel display. In this case, check the following table. When displaying the version number on the TV screen When you turn on the system, the version number [VER.X.XX] (X is a number) may appear on the TV screen. Although this is not a malfunction and for Sony service use only, normal system operation will not be possible. Turn off the system, and then turn on the system again to operate. Self-diagnosis Function First 3 characters of the service number Cause and corrective action C 13 This disc is dirty. • Clean the disc with a soft cloth. C 31 The disc is not inserted correctly. • Restart the system, then re-insert the disc correctly. E XX (XX is a number) To prevent a malfunction, the system has performed the self-diagnosis function. • Contact your nearest Sony dealer or local authorized Sony service facility and give the 5-character service number. Example: E 61 10 VER.X.XX This appliance is classified as a CLASS 1 LASER product. This label is located on the rear exterior. The following caution label is located inside the apparatus. Ver. 1.1 SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) Fig. A. Using an AC voltmeter to check AC leakage. 1.5 kΩ 0.15 µF AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground

1. SERVICING NOTES ............................................... 5 2. GENERAL ................................................................... 7 3. DISASSEMBLY 3-1. Disassembly Flow ........................................................... 8 3-2. Case ................................................................................. 9 3-3. Escution Top Block ......................................................... 9 3-4. Loading Panel .................................................................. 10 3-5. Tuner (FM/AM) (TM10SE) ............................................ 10 3-6. DVD Mechanism Deck Block ......................................... 11 3-7. Front Panel Block ............................................................ 11 3-8. Back Panel Block ............................................................ 12 3-9. MAIN Board Block ......................................................... 12 3-10. MAIN Board.................................................................... 13 3-11. Cover (CDM)................................................................... 13 3-12. DRIVER Board, SW Board............................................. 14 3-13. Optical Pick-Up Block (KHM-310CAB or KHM-313CAB) ............................... 14 3-14. SENSOR Board ............................................................... 15 3-15. MOTOR (TB) Board ....................................................... 15 3-16. MOTOR (LD) Board ....................................................... 16 4. TEST MODE .............................................................. 17 5. MECHANICAL ADJUSTMENTS ....................... 21 6. ELECTRICAL ADJUSTMENTS ......................... 21 7. DIAGRAMS 7-1. Block Diagram – RF SERVO/VIDEO Section – ............ 23 7-2. Block Diagram – MIC/EFFECTOR Section – ................ 24 7-3. Block Diagram – TUNER/TAPE Section – .................... 25 7-4. Block Diagram – AUDIO Section – ................................ 26 7-5. Block Diagram – AMP Section – .................................... 27 7-6. Block Diagram – PANEL/POWER SUPPLY Section – ........................... 28 7-7. Printed Wiring Board – DMB15 Board (Side A) – ......... 30 7-8. Printed Wiring Board – DMB15 Board (Side B) – ......... 31 7-9. Schematic Diagram – DMB15 Board (1/4) –.................. 32 7-10. Schematic Diagram – DMB15 Board (2/4) –.................. 33 7-11. Schematic Diagram – DMB15 Board (3/4) –.................. 34 7-12. Schematic Diagram – DMB15 Board (4/4) –.................. 35 7-13. Printed Wiring Boards – CHANGER Section – .............. 36 7-14. Schematic Diagram – CHANGER Section – .................. 37 7-15. Printed Wiring Board – VIDEO Board –......................... 38 7-16. Schematic Diagram – VIDEO Board – ........................... 39 7-17. Printed Wiring Board – MIC Board – ............................. 40 7-18. Schematic Diagram – MIC Board – ................................ 41 7-19. Printed Wiring Board – EFFECTOR Board – ................. 42 7-20. Schematic Diagram – EFFECTOR Board –.................... 43 7-21. Printed Wiring Board – KARAOKE Board – ................. 44 7-22. Schematic Diagram – KARAOKE Board – .................... 44 7-23. Printed Wiring Board – MAIN Board – .......................... 45 7-24. Schematic Diagram – MAIN Board (1/6) – .................... 46 7-25. Schematic Diagram – MAIN Board (2/6) – .................... 47 7-26. Schematic Diagram – MAIN Board (3/6) – .................... 48 7-27. Schematic Diagram – MAIN Board (4/6) – .................... 49 7-28. Schematic Diagram – MAIN Board (5/6) – .................... 50 7-29. Schematic Diagram – MAIN Board (6/6) – .................... 51 7-30. Printed Wiring Board – PA Board – ................................ 52 7-31. Schematic Diagram – PA Board – ................................... 53 7-32. Printed Wiring Board – SURROUND Board – ............... 55 7-33. Schematic Diagram – SURROUND Board (1/2) – ......... 56 7-34. Schematic Diagram – SURROUND Board (2/2) – ......... 57 7-35. Printed Wiring Board – PANEL Board – ........................ 58 7-36. Schematic Diagram – PANEL Board – ........................... 59 7-37. Printed Wiring Boards – FRONT KEY Section – ........... 60 7-38. Schematic Diagram – FRONT KEY Section – ............... 61 7-39. Printed Wiring Boards – TOP KEY Section – ................ 62 7-40. Schematic Diagram – TOP KEY Section – ..................... 63 7-41. Printed Wiring Board – TRANSFORMER Board – ....... 64 7-42. Printed Wiring Board – PRIMARY Board – ................... 65 7-43. Schematic Diagram – POWER SUPPLY Section – ........ 66 8. EXPLODED VIEWS 8-1. Case, Escutcheon Top Section ......................................... 81 8-2. PANEL Board Section ..................................................... 82 8-3. Tape Mecha Deck Section ............................................... 83 8-4. Back Panel Section .......................................................... 84 8-5. DMB15/KARAOKE/VIDEO Boards Section................. 85 8-6. MAIN/PA/SURROUND Boards Section ........................ 86 8-7. Power Transformer Section ............................................. 87 8-8. DVD Mechanism Deck Section-1 (CDM74HF-DVBU101).................................................. 88 8-9. DVD Mechanism Deck Section-2 (CDM74HF-DVBU101).................................................. 89 9. ELECTRICAL PARTS LIST ................................ 90 Note: Refer to SUPPLEMENT-1 for the MAIN board of printed wiring board, schematic diagram and electrical parts list of US model. Ver. 1.1

Label indication Model 2-661-760-5[] E2 ZX80D: E2 2-661-760-6[] E2 ZX100D: E2 2-661-761-3[] MX ZX100D: MX 2-661-761-4[] MX ZX80D: MX 2-672-142-0[] E3 ZX100D: E3 2-672-142-1[] E3 ZX80D: E3 2-675-973-2[] E51 ZX80D: E51 2-675-973-3[] E51 ZX100D: E51 2-686-974-1[] SP2/6 ZX100D: SP, MY 2-686-106-0[] E13 ZX80D: E3 2-899-693-0[] U2 ZX80D: US • Abbreviation E2 : 120V AC area in E model E3 : 240V AC area in E model E13 : Russian model and 220V – 230V AC area in E model E51 : Chilean and Peruvian models MX : Mexican model MY : Malaysia model SP : Singapore model HOW TO IDENTIFY OPTICAL PICK-UP BLOCK There are two kinds of OPTICAL PICK-UP BLOCK in this set. When replacing the OPTICAL PICK-UP BLOCK, make sure which OPTICAL PICK-UP BLOCK it is following the “How to Identify” in the figure shown below. SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40 °C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. RELEASING THE DVD TRAY LOCK The disc tray lock function for the antitheft of an demonstration disc in the store is equipped. Releasing Procedure : 1. Press the I/1 button to turn the power on. 2. Press the DVD button to select “DVD”. 3. While pressing the x button, press the Z OPEN/CLOSE button until “UNLOCKED” displayed on the fluorescent indicator tube (around 5 seconds). Note: When “LOCKED” is displayed, the disc tray lock is not released by turning power on/off with the I/1 button. NOTES ON REPLACEMENT OF THE DMB15 BOARD New part of EEPROM (IC103) on the DMB15 board cannot be used. Therefore, if the mounted DMB15 board is replaced, exchange new EEPROM with that used before the replacement. Model number label Printed of KHM-310CAB or KHM-313CAB. KHM-310CAB or KHM-313CAB Ver. 1.1

system. Other discs cannot be played back. List of playable discs “DVD+RW”, “DVD-RW”, “DVD+R”, “DVD VIDEO”, and the “CD” logos are trademarks. Notes on discs The system can play back the following disc: • CD-ROMs/CD-Rs/CD-RWs recorded in the following formats: – VIDEO CD format – AUDIO CD format – CD Graphics (Latin American models only) – DATA CD format which contains MP3 audio tracks, JPEG image files and DivX 1) video files of format conforming to ISO 2) 9660 Level 1, Level 2 or Joliet in 3) expansion format • DVD-ROMs/DVD-Rs/DVD-RWs/DVD+Rs/ DVD+RWs recorded in the following formats: – DVD VIDEO format – DATA DVD format which contains MP3 audio tracks, JPEG image files and DivX 1) video files of format conforming to UDF 2) (Universal Disk Format) – VR (Video Recording) format (DVD-Rs/ DVD-RWs only) The system cannot play back the following discs: 1) MP3 audio tracks must be in MPEG 1 Audio Layer 3 format. 2) DivX video files must be recorded in DivX format with the extension “.AVI” or “.DIVX”. (Except US model) 3) ISO 9660 Format A logical format of files and folders on CD-ROMs, defined by ISO (International Organization for Standardization). Playable discs Format of discs Disc logo DVD VIDEO DVD-RW/DVD-R DVD+RW/ DVD+R VIDEO CD AUDIO CD CD Graphics (CDG) (Latin American models only) CD-R/CD-RW 4) CD-Extra: This format records audio (AUDIO CD data) on the tracks in session 1 and data on the tracks in session 2. 5)Mixed CD: This format records data on the first track and audio (AUDIO CD data) on the second and subsequent tracks of a session. Region code of DVD VIDEOs you can play back on this system Your system has a region code printed on the back of the unit and will only play back DVD VIDEOs labeled with identical region code. DVD VIDEOs labeled will also be played back on this system. If you try to play back any other region code DVD VIDEO, the message “Playback prohibited by area limitations.” will appear on the TV screen. Depending on the DVD VIDEO, no region code indication may be labeled even though playing the DVD VIDEO is prohibited by area restrictions. Example: Note on DualDiscs A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to Compact Disc (CD) standard, playback on this product is not guaranteed. ALL DVD DECK RECEIVER MODELN0. HCD-ZX100D SERIAL NO. AC:120-127/220/230-240V 50/60Hz430W Region code Notes on CD-R/CD-RW/DVD-R/ DVD-RW/DVD+R/DVD+RW • In some cases, CD-Rs/CD-RWs/DVD-Rs/ DVD-RWs/DVD+Rs/DVD+RWs cannot be played back on this system due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. The disc will not be played back if it has not been correctly finalized. For more information, see the operation instructions for the recording device. • Note that some playback functions may not work with some DVD+RWs/DVD+Rs, even if they have been correctly finalized. In this case, view the disc by normal playback. • A disc created in Packet Write format cannot be played back. Note on playback operations of DVD VIDEOs and VIDEO CDs Some playback operations of DVD VIDEOs and VIDEO CDs may be intentionally set by software producers. Since this system play back DVD VIDEOs and VIDEO CDs according to the disc contents the software producers designed, some playback features may not be available. Also, refer to the instructions supplied with the DVD VIDEOs or VIDEO CDs. Note on PBC (Playback Control) (VIDEO CDs) This system conforms to Ver. 1.1 and Ver. 2.0 of VIDEO CD standards. You can enjoy two kinds of playback depending on the disc type. Disc type You can VIDEO CDs without PBC functions (Ver. 1.1 discs) Enjoy video playback (moving pictures) as well as music. Music discs encoded with copyright protection technologies This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. Notes on Multi Session disc • This system can play back Multi Session discs when an MP3 audio track is contained in the first session. Any subsequent MP3 audio tracks recorded in later sessions can also be played back. • This system can play back Multi Session discs when a JPEG image file is contained in the first session. Any subsequent JPEG image files recorded in later sessions can also be played back. • If the first session is recorded in AUDIO CD or VIDEO CD format, only the first session will be played back. VIDEO CDs with PBC functions (Ver. 2.0 discs) Play back interactive software using menu screens displayed on the TV screen (PBC Playback), in addition to the video playback functions of Ver. 1.1 discs. Moreover, you can play back high- resolution still pictures, if they are included on the disc. Disc type You can • The system will recognize a Multi Session disc as an AUDIO CD if there is a session recorded in AUDIO CD format on the disc. However, the system will only play back the disc if the first session is recorded in AUDIO CD format. • With DATA CD or DATA DVD, the system will only play back DivX video files even if it contains MP3 audio tracks or JPEG image files. • CD-ROMs recorded in PHOTO CD format • Data part of CD-Extras4) • Data part of Mixed CDs5) • Super Audio CDs • DVD Audio discs • DVD-RAMs • A DVD VIDEO with a different region code. • A disc that has a non-standard shape (e.g., heart, square, star). • A disc that has the adhesive cellophane tape or a sticker still left on it. Ver. 1.1

instruction manual. LOCATION OF CONTROLS Remote control ADVANCE wf ALBUM +/– qa ANGLE q; AUDIO 8 CLEAR wk DISC SKIP 3 DISPLAY ed ENTER wh FM MODE 7 FUNCTION +/– 4 KARAOKE MODE ea KARAOKE PON e; KEY CONTROL #/2 es MENU qs Numeric Buttons1) wl PICTURE NAVI 6 PRESET + qh PRESET – wd REPEAT 7 REPLAY wf SCORE 5 SLEEP eg SLOW qj SLOW ws SOUND FIELD qd STEP C wf SUBTITLE 9 THEATRE SYNC 1 TIMER MENU eh TIME/TEXT ef TOP MENU wj TUNING + qj TUNING – ws TV w; TV CH + qh TV CH – wd TV/VIDEO eg TV VOL +/– qf 1) TV &/1 (on/standby) 2 VOLUME +/– qf 1) ?/1 (on/standby) 2 x (stop) qk X (pause) ql H1) (play) wa > (go forward) qh . (go backward) wd M (fast forward) qj m (rewind) ws V/v/B/b wh 10/0 wl -/-- wk O RETURN wg DISPLAY qg c STEP wf 1) The numeric button 5, TV VOL +, VOLUME + and H buttons have a tactile dot. Use the tactile dot as a reference when operating the system. ALPHABETICAL ORDER A – L M – S T – Z NUMBERS AND SYMBOLS Unit AMP MENU e; BALANCE rh BEAT JUMP rs BEAT MAX ra BEAT PAD r; CD SYNC q; CHORUS wl Deck A ea Deck B qk DELAY wk DIRECTION ql DISC 1 ~ 3 ts Disc tray 8 DISPLAY 2 Display 6 DVD ej ECHO LEVEL ws ENTER wa EQ BAND w; EX-CHANGE/DISC SKIP t; FADER rg FLANGER 3 GROOVE qh ILLUMINATION 1 IR Receptor ek MASTER VOLUME wf MIC 1/2 (jack) wg MIC 1/2 LEVEL wd OPERATION DIAL ta PHONES (jack) wj Power illuminator 5 PRESET +/– qf PROGRESSIVE 7 RANDOM rd REC PAUSE/START 9 SOUND FIELD 4 SPEAKERS rj TAPE A/B eg TUNER/BAND eh TUNING +/– qg TV/SAT ef VIDEO INPUT (jacks) wh VIDEO ed X-ROUND JOG rk X-ROUND OFF rj WAVE rf ?/1 (on/standby) el Z OPEN/CLOSE rl nN (play) qa .> (go backward/forward) qf mM (rewind/fast forward) qg X (pause) qs x (stop) qd A Z (Eject A) es B Z (Eject qj ALPHABETICAL ORDER A – D E – L M – R S – Z SYMBOLS Front Panel Top Panel 1 2 3 4 567 8 9 q; qa qs qd qf qg qh qj qk wa w; ql ws wd wf wg wh wj e; wl wk ea es ed ef eg eh ej ek el rg rf rd rs ra r; tsta t;rl rj rh rk 7 5 q; qh qj qk ql wa wd wf wh wj wk wl ea es ed ef eg eh e; qg qf qs qa 9 8 6 4 3 1 2 w; ws wg qd 1 Press ?/1 to turn on the system. 2 Press TIMER MENU. The hour indication flashes in the display. 3 Press V or v repeatedly to set the hour. 4 Press ENTER. The minute indication flashes in the display. 5 Press V or v repeatedly to set the minute. 6 Press ENTER. The clock starts functioning. To adjust the clock 1 Press TIMER MENU. “PLAY SET?” flashes in the display. 2 Press V or v repeatedly to select “CLOCK SET?”, then press ENTER. The hour indication flashes in the display. 3 Do the same procedures as step 3 to 6 above. Notes • The clock settings are canceled when you disconnect the power cord or if a power failure occurs. • You cannot set the clock in Power Saving Mode. Setting the clock

3-1. DISASSEMBLY FLOW SET 3-2. CASE (Page 9) 3-3. ESCUTCHEON TOP BLOCK (Page 9) 3-4. LOADING PANEL (Page 10) 3-9. MAIN BOARD BLOCK (Page 12) 3-12. DRIVER BOARD, SW BOARD (Page 14) 3-13. OPTICAL PICK-UP BLOCK (KHM-310CAB or KHM-313CAB) (Page 14) 3-10. MAIN BOARD (Page 13) 3-15. MOTOR (TB) BOARD (Page 15) 3-16. MOTOR (LD) BOARD (Page 16) 3-7. FRONT PANEL BLOCK (Page 11) 3-5. TUNER (FM/AM) (TM10SE) (Page 10) 3-6. DVD MECHANISM DECK BLOCK (Page 11) 3-14. SENSOR BOARD (Page 15) 3-8. BACK PANEL BLOCK (Page 12) 3-11. COVER (CDM) (Page 13) Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed.

3-2. CASE 3-3. ESCUTCHEON TOP BLOCK 3 screw (case 3 TP2) 5 case 2 two screws (BVTP 3 ×10) 1 three screws (BVTP 3 × 10) 3 screw (case 3 TP2) 2 two screws (BVTP 3 ×10) 4 two screws (case 3 TP2) 4 two screws (case 3 TP2) 3 wire (flat type) (7 core) (CN1153) 2 boss 4 escutcheon top block 2 boss 1 screw (BVTP 3 × 12) 1 screw (BVTP 3 × 12)

3-4. LOADING PANEL 3 four claws 1 Turn the gear (loading A) to the direction of the arrow. 2 4 loading panel 3 tuner (FM/AM) (TM10SE) 2 two screws (BVTT 3 × 8) 1 wire (flat type) (9 core)

3 wire (flat type) (21 core) (CN302) 4 three connectors (CN401, CN800, NO2000) 4 connector (CN802) 1 wire (flat type) (13 core) (CN106) 6 7 2 wire (flat type) (13 core) (CN701) 5 four screws (BVTT 3 × 10) 5 three screws (BVTT 3 × 10) 4 six screws (BVTP 3 × 8) 3 connector (CN1102) 6 wire (flat type) (17 core) (CN508) 2 ground wire 1 screw (BV3 (3-CR)) 7 wire (flat type) (11 core) (CN509) 8 three connectors (CN100, CN503, CN504) 9 front panel block 5 3-6. DVD MECHANISM DECK BLOCK 3-7. FRONT PANEL BLOCK

3-9. MAIN BOARD BLOCK 2 connector (CN1204) 2 connector (CN1202) 2 connector (CN1200) 5 connector (CN580) 4 3 screw (BVTT 3 × 10) 3 four screws (BVTT 3 × 10) 3 three screws (BVTT 3 × 10) 3 two screws (BVTT 3 × 10) 6 back panel block 1 wire (flat type) (19 core) (CN1502) 3 three screws (BV3 (3-CR)) 3 screw (BV3 (3-CR)) 6 MAIN board block 5 two screws (BVTT 3 × 8) 4 screw (BVTT 3 × 10) 1 screw (BVTT 3 × 8) 2 ground wire

3 MAIN board 2 two connectors (CN513, CN514) 1 screw (BVTT 3 × 8) 2 two connectors (CN501, CN502) 3-11. COVER (CDM) 2 KARAOKE board 1 two screws (BVTT 3 × 10) 8 three screws (BVTT 3 × 10) 7 connector (CN201) 9 cover (CDM) 6 wire (flat type) (24 core) (CN101) 4 two screws (BVTT 3 × 10) 3 wire (flat type) (13 core) (CN801) 5 VIDEO board

3-13. OPTICAL PICK-UP BLOCK (KHM-310CAB or KHM-313CAB) 3 connector (CN703) 4 DRIVER board 6 SW board 2 wire (flat type) (5 core) (CN702) 1 two screws (BTTP (M2.6)) 5 screw (BTTP (M2.6)) 1 floating screw (PTPWH M2.6) 5 connector 2 holder (310) assy 6 wire (flat type) (24 core) 7 optical pick-up block (KHM-310CAB or KHM-313CAB) 4 two insulators 3 two insulator screws 3 two insulator screws 4 two insulators

2 tray 3 belt (table) 5 pulley (table) 8 screw (BTTP (M2.6)) 0 SENSOR board 7 gear (geneva) 9 connector (CN731) 1 floating screw (PTPWH M2.6) 6 floating screw (PTPWH M2.6) 4 floating screw (PTPWH M2.6) 3-15. MOTOR (TB) BOARD 6 Remove the two solderings of motor. 8 MOTOR (TB) board 7 table motor assy (M741) 5 two screws (BTTP (M2.6)) 4 3 wire (flat type) (5 core) (CN742) 1 stopper 2 stopper

3 Remove the two solderings of motor. 4 MOTOR (LD) board 1 belt (loading) 5 loading motor assy (M751) 2 two screws (BTTP (M2.6))

This mode is used to check the fluorescent indicator tube, LEDs, keys, MASTER VOLUME knob, OPERATION DIAL knob, X- ROUND JOG knob, model, destination, software version and VACS level. Procedure: 1. Press three buttons of x , [ENTER] and [DISC 2] simultaneously. 2. All LEDs except I/1 LED (green color) and segments in fluorescent indicator tube are lighted up. 3. When you want to enter the software version display mode, press the [DISC 1] button. The model information appears on the fluorescent indicator tube. 4. Each time the [DISC 1] button is pressed, the display changes from destination information, MC version, GC version, SYS version, DVD version, ST version, TC version, TA version, TM version in this order, and returns to the model information display. 5. When the [DISC 3] button is pressed while the version numbers are being displayed except model information and destination information, the date of the software creation appears. When the [DISC 3] button is pressed again, the display returns to the software version display. When the [DISC 1] button is pressed while the date of the software creation is being displayed, the date of the software creation is displayed in the same order of software version display. 6. Press the [DISC 2] button, the key check mode is activated. 7. In the key check mode, the fluorescent indicator tube displays “K 0 V0J0 X0”. Each time a button is pressed, “K 0” value increases. However, once a button has been pressed, it is no longer taken into account. 8. “V” value increases in the manner of 0, 1, 2, 3 ... if the [MASTER VOLUME] knob is turned clockwise, or it decreases in the manner of 0, 9, 8, 7 ... if the [MASTER VOLUME] knob is turned counterclockwise. “J” value increases in the manner of 0, 1, 2, 3 ... if the [OPERATION DIAL] knob is turned clockwise, or it decreases in the manner of 0, 9, 8, 7 ... if the [OPERATION DIAL] knob is turned counterclockwise. “X” value increases in the manner of 0, 1, 2, 3 ... if the [X- ROUND JOG] knob is turned clockwise, or it decreases in the manner of 0, 9, 8, 7 ... if the [X-ROUND JOG] knob is turned counterclockwise. 9. When the [DISC 3] button is pressed after all LEDs except I/1 LED (green color) and segments in fluorescent indicator tube light up, the fluorescent indicator tube displays “VACS A+B F APC”. A is conventional VACS level which is triggered by signal level. B is thermal VACS level which is triggered by temperature F is shown if the fan is turned in high speed and vice-versa. C is VACS level which is triggered by APVACS (Abuse Protection VACS). The signal level , which will trigger VACS A is shown in the center area of the fluorescent indicator tube. 10. When [EX-CHANGE/DISC SKIP] button is pressed after all LEDs except I/1 LED (green color) and segments in fluorescent indicator tube light up, alternate segments in fluorescent indicator tube and LEDs would light up. If you press [EX- CHANGE/DISC SKIP] button again, another half of alternate segments in fluorescent indicator tube and LEDs would light up. Press [EX-CHANGE/DISC SKIP] button again would cause all LEDs except I/1 LED (green color) and segments in fluorescent indicator tube lights up. 11. To release from this mode, press three buttons in the same manner as step 1 or disconnect the power cord. SECTION 4 TEST MODE COMMON TEST MODE This mode is used to check operations of the respective sections of amplifier and tape. Procedure: • To enter common test mode 1. Press three buttons of x , [ENTER] and [DISC 3] simultaneously. 2. The DVD ring indicators, tape A and B indicators and the line below DVD ring indicators and tape A and B indicators flash synchronously on the fluorescent indicator tube. The function is changed to “TV”. • Check of amplifier 1. Press the [EQ BAND] button repeatedly until a message “GEQ MAX” appears on the fluorescent indicator tube. GEQ increases to its maximum. 2. Press the [EQ BAND] button repeatedly until a message “GEQ MIN” appears on the fluorescent indicator tube. GEQ decreases to its minimum. 3. Press the [EQ BAND] button repeatedly until a message “GEQ FLAT” appears on the fluorescent indicator tube. GEQ is set to flat. 4. When the [MASTER VOLUME] knob is turned clockwise even slightly, the sound volume increases to its maximum and a message “VOLUME MAX” appears on the fluorescent indicator tube. 5. When the [MASTER VOLUME] knob is turned counterclockwise even slightly, the sound volume decreases to its minimum and a message “VOLUME MIN” appears on the fluorescent indicator tube. • Tape function 1. When a tape is inserted in deck-B and recording is started, the function is changed to “TV” automatically. When the [CD SYNC] button is pressed during recording in function, ALC (Automatic Logic Control) is turned on. 2. During recording, press the m button will stop the recording and the function is changed to “TAPE B” and rewind the tape in deck-B until the recording start position and playback of the tape is started. If the [REC PAUSE/START] button is pressed for a pause and pressed again to resume recording during recording time, when the tape is rewind, the tape will be rewind until the position where the pause is applied. • To release common test mode 1. To release from this mode, press the I/1 button. 2. The cold reset is enforced at the same time. COLD RESET The cold reset clears all data including preset data stored in the RAM to initial conditions. Procedure: 1. Press the I/1 button to turn on the system. 2. Press three buttons of x , [ENTER] and I/1 simultaneously. 3. The message “COLD RESET“ appears on the fluorescent indicator tube. Then, the fluorescent indicator tube becomes blink for a while , and the system is reset. VACS ON/OFF This mode is used to switch on and off the VACS (Variable Attenuation Control System). Procedure: 1. Press the I/1 button to turn on the system. 2. Press two buttons of x and [ILLUMINATION] simultaneously. The message “VACS OFF” or “VACS ON” appears on the fluorescent indicator tube.

The step interval of AM channels can be toggled between 9 kHz and 10 kHz. This mode is not available for Russian model. Procedure: 1. Press the I/1 button to turn on the system. 2. Press the [TUNER/BAND] button repeatedly to select the “AM”. 3. Press the I/1 button to turn off the system. 4. Press two buttons of [ENTER] and I/1 simultaneously. The system will turn on automatically. The message “AM 9k STEP” or AM 10k STEP” appears on the fluorescent indicator tube and thus the channel step is changed. DVD SHIP MODE (WITH MEMORY CLEAR) This mode moves the optical pick-up to the position durable to vibration and clears all data including preset data stored in the RAM to initial conditions. Use this mode when returning the set to the customer after repair. Procedure: 1. Press the I/1 button to turn on the system. 2. Press the [DVD] button to select the “DVD”. 3. Press three buttons of x , [DELAY] and I/1 simultaneously during “DVD No Disc” condition. The system will turn off automatically. 4. After the “STANDBY” blinking display finishes, a message “MECHA LOCK” appears on the fluorescent indicator tube and the DVD ship mode is set. DVD SHIP MODE (WITHOUT MEMORY CLEAR) This mode moves the optical pick-up to the position durable to vibration. Procedure: 1. Press the I/1 button to turn on the system. 2. Press the [DVD] button to select the “DVD”. 3. Press two buttons of [DVD] and I/1 simultaneously during “DVD No Disc” condition. The system will turn off automatically. 4. After the “STANDBY” blinking display finishes, a message “MECHA LOCK” appears on the fluorescent indicator tube and the DVD ship mode is set. DVD TRAY LOCK MODE This mode is used to lock the disc tray. When this mode is activated, the disc tray will not open when Z OPEN/CLOSE button or [EX- CHANGE/DISC SKIP] button is pressed. The message “LOCKED” appears on the fluorescent indicator tube. Procedure: 1. Press the I/1 button to turn on the system. 2. Press the [DVD] button to select the “DVD”. 3. Press two buttons of x and Z OPEN/CLOSE simultaneously and hold down until “LOCKED” or “UNLOCKED” appears on the fluorescent indicator tube (around 5 seconds). TV/SAT SWITCHING This mode let you switch from TV to SAT and vice-versa. Procedure: 1. Press the I/1 button to turn on the system. 2. Press the [TV/SAT] button to select the “TV”. 3. Press two buttons of [TV/SAT] and I/1 simultaneously. The function will changed to SAT. Press the same buttons again to change from SAT to TV. DVD COLOR SYSTEM This mode let you change the color system of the video output from PAL to NTSC or vice-versa. This mode is not available for Latin American model and Russian models. Procedure: 1. Press the I/1 button to turn on the system. 2. Press the [DVD] button to select the “DVD”. 3. Press the I/1 button to turn off the system. 4. Press two buttons of X and I/1 simultaneously. The system will turn on automatically. The message “COLOR PAL” or “COLOR NTSC” appears on the fluorescent indicator tube. REMOTE DISABLE MODE This mode let you disable the remote commander reception. When this mode is activated, the system will not response if the button on the remote commander is pressed. The message “RemoteDisable” appears on the fluorescent indicator tube. This mode is essential for conducting test and repairing when no interruption from the other remote commander is expected. This mode is cancelled automatically when the AC power supply is cutoff. Procedure: 1. Press the I/1 button to turn on the system. 2. Press three buttons of x , [FLANGER] and [DISC 2] simultaneously until “RemoteDisable” or “RemoteEnable” appears on the fluorescent indicator tube. TCM OFFLINE MODE This mode is used to prevent the system from turning off automatically when TCM is not connected. Therefore, measurements can be done even when TCM is not connected during production. Procedure: 1. When the system is turned off, press three buttons of [EQ BAND], [TAPE A/B] and I/1 simultaneously. The system will turn on automatically. 2. The message “TCM OFFLINE” appears on the fluorescent indicator tube. MTK FIRMWARE DISPLAY This mode is used to display the MTK firmware version. Procedure: 1. Press the I/1 button to turn on the system. 2. Press the [DVD] button to select the “DVD”. 3. Press the I/1 button to turn off the system. 4. Press two buttons of x and I/1 simultaneously. The system will turn on automatically. 5. The version of MTK firmware appears on the TV screen. MTK OFFLINE This mode is used to enable audio output from the function other than DVD function in order to check the audio output from the system without connecting MTK. Procedure: 1. Press the I/1 button to turn on the system. 2. Press three buttons of x , [FLANGER] and [DISC 1] simultaneously and the message “MTK OFFLINE” appears on the fluorescent indicator tube.

This mode let you make diagnosis and adjustment easily by using the remote commander and the TV screen. The instructions, diagnostic results, etc. are given on the on-screen display. 2. ENTERING DVD SERVICE MODE Procedure: 1. Press the I/1 button to turn on the system. 2. Press the [DVD] button to select the “DVD”. 3. Press two buttons x and Z OPEN/CLOSE simultaneously and then turn the [MASTER VOLUME] knob clockwise. 4. The message “SERVICE IN” appears on the fluorescent indicator tube and top menu of the Remocon Diagnosis Menu appears on the on-screen display on the TV screen as follows. The model name, IF-con version and Syscon version are displayed at the bottom of the on-screen display. Remocon Diagnosis Menu 0. External Chip Check 1. Servo Parameter Check 2. Drive Manual Operation 3. Emergency History 4. Version Information Model Name :xxxxxxxxxx IF-con:Ver.xx.xx(xxxx) Syscon:Ver.x.xxx 5. To execute each function, press its number by using numeric button on the remote commander. 6. To release from this mode, press the I/1 button to turn off the system. 3. EXECUTING IOP MEASUREMENT In order to execute IOP measurement, the following standard procedures must be followed. Procedure: 1. From the top menu of Remocon Diagnosis Menu, select “2 Drive Manual Operation” by pressing the [2] button on the remote commander. The following screen appears on the on- screen display Drive Manual Operation 1. Servo Control 2. Track/Layer Jump 3. Manual Adjustment 4. Mecha Test Mode 5. MIRR time Adjust 0. Return to Top Menu 2. Select “3. Manual Adjustment” by pressing the [3] button on the remote commander. The following screen appears on the on-screen display. Manual Adjust 1. Track Balance Adjust: 2. Track Gain Adjust: 3. Focus Balance Adjust: 4. Focus Gain Adjust: 5. Eq boost Adjust: 6. Iop: 7. TRV. Level: 8. S curve(FE) Level: 9. RFL(PI) Level: 0. MIRR Time: V v Change Value [RETURN]Return to previous menu 3. Select “6. Iop:” by pressing [6] button on the remote commander. 4. Wait until a hexadecimal number appear in the on-screen display as below. Manual Adjust 1. Track Balance Adjust: 2. Track Gain Adjust: 3. Focus Balance Adjust: 4. Focus Gain Adjust: 5. Eq boost Adjust: 6. Iop: ED: 7. TRV. Level: 8. S curve(FE) Level: 9. RFL(PI) Level: 0. MIRR Time: V v Change Value [RETURN]Return to previous menu 5. Convert data from hexadecimal to decimal by using conversion table. 6. Please find the label on the rear of the BU (Base Unit). The default IOP values is written in the label. 7. Subtract between these two values. 8. If the value is smaller than 93 (decimal), then it is OK. However if the value is higher than 93, then BU (base unit) is defective and need to be change. 9. Press the O RETURN button on the remote commander to return to previous menu. 10. Press the [0] button on the remote commander to return to the top menu of Remocon Diagnosis Menu. 11. Press the I/1 button to turn off the system. Ver. 1.2

To check the emergency history, please follow the following procedure. Procedure: 1. From the top menu of Remocon Diagnosis Menu, select “3. Emergency History” by pressing the [3] button on the remote commander. The following screen appears on the on-screen display. Emg. History Check Laser Hours CD 999h 59min DVD 999h 59min 01. 01 05 04 04 00 92 46 00 00 00 00 00 00 00 23 45 02. 02 02 01 01 00 A9 4B 00 00 00 00 00 00 00 23 45 [Next]Next page [Prev]Prev page [0]Return to Top Menu 2. You can check the total time when the laser is turned on during playback of DVD and CD from the above menu. The maximum time, which can be displayed are 999h 59min. 3. You can check the error code of latest 10 emergency history from the above menu. To view the previous or next page of emergency history, press the . or > button on the remote commander. The error code consists of three kinds of error codes. A. Error code Example of Error code 01. 01 05 04 04 00 92 46 00 00 00 00 00 00 00 23 45 The meaning of error code is as below: 01: Communication error (No reply from syscon) 02: Syscon hung up 03: Power OFF request when syscon hung up 19: Thermal shutdown 24: MoveSledHome error 25: Mechanical move error (5 changer) 26: Mechanical move stack error 30: DC motor adjustment error 31: DPD offset adjustment error 32: TE balance adjustment error 33. TE sensor adjustment error 34. TE loop gain adjustment error 35. FE loop gain adjustment error 36. Bad jitter after adjustment 40. Focus NG 42. Focus layer jump NG 52. Open kick spindle error 51: Spindle stop error 60: Focus on error 61: Seek fail error 62: Read Q data/ID error 70: Lead in data read fail 71: TOC read time out (CD) 80: Can’t buffering 81: Unknown media type B. Parameter of error code This is the detail of error code. Example of Error code 01. 01 05 04 04 00 92 46 00 00 00 00 00 00 00 23 45 C. Time of error code This is the laser time when an error occurred. Example of Error code 01. 01 05 04 04 00 92 46 00 00 00 00 00 00 00 23 45 To Clear the Laser Hour Press the [ DISPLAY] button on the remote commander and then press the [CLEAR] button on the remote commander. The data for both CD and DVD data are reset. Emg. History Check Laser Hours CD 0h 0min DVD 0h 0min 01. 01 05 04 04 00 92 46 00 00 00 00 00 00 00 23 45 02. 02 02 01 01 00 A9 4B 00 00 00 00 00 00 00 23 45 [Next]Next page [Prev]Prev page [0]Return to Top Menu To Clear the Emergency History Press the [DVD TOP MENU] button on the remote commander and then press the [CLEAR] button on the remote commander. The error code for all emergency history would be reset. Emg. History Check Laser Hours CD 999h 59min DVD 999h 59min 01. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [Next]Next page [Prev]Prev page [0]Return to Top Menu Ver. 1.2

Procedure: 1. Press the [DVD MENU] button on the remote commander and then press the [CLEAR] button on the remote commander. The following screen appears on the on-screen display. Emg. History Check Laser Hours CD 999h 59min DVD 999h 59min Initialize setup data... [Next]Next page [Prev]Prev page [0]Return to Top Menu 2. The screen after a while returns to former display. To Return to the Top Menu of Remocon Diagnosis Menu Press the [0] button on the remote commander. 5. CHECKING VERSION INFORMATION To check the version information, please follow the following procedure. Procedure: 1. From the top menu of Remocon Diagnosis Menu, select “4. Version Information” by pressing the [4] button on the remote commander. The following screen appears on the on-screen display. Version information Firm(Main): Ver. X.XXXX Firm(Sub): XX.XX RISC: XXXXXX 8032: XXXXXX Audio DSP: XX.XX.XX.XX Servo DSP: XX.XX.XX.XX [0]Return to Top Menu 2. To return to the top menu of Remocon Diagnosis Menu, press the [0] on the remote commander. SECTION 5 MECHANICAL ADJUSTMENTS PRECAUTION 1. Clean the following parts with a denatured-alcohol-moistened swab : record/playback head pinch roller erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, appiy suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. TORQUE MEASUREMENT Mode Torque Meter Meter Reading 3.06 – 6.96 mN⋅m FWD CQ-102C (31 – 71 g⋅cm) (0.43 – 0.98 oz⋅inch) FWD 0.19 – 0.58 mN⋅m Back Tension CQ-102C (2.0 – 6.0 g⋅cm) (0.02 – 0.08 oz⋅inch) 3.06 – 6.96 mN⋅m REV CQ-102RC (31 – 71 g⋅cm) (0.43 – 0.98 oz⋅inch) REV 0.19 – 0.58 mN⋅m Back Tension CQ-102RC (2.0 – 6.0 g⋅cm) (0.02 – 0.08 oz⋅inch) 6.96 – 14.02 mN⋅m FF/REW CQ-201B (71 – 143 g⋅cm) 0.98 – 1.99 oz⋅inch) 9.80 mN⋅m FWD CQ-403A more than 100 g (more than 3.53 oz) 9.80 mN⋅m REV CQ-403R more than 100 g (more than 3.53 oz) Ver. 1.2

Use the following test disc on electrical adjustments. YEDS-18 (CD) : PART No. 3-702-101-01 PATD-012 (CD) : PART No. 4-225-203-01 HLX-503 (DVD-SL) (NTSC) : PART No. J-6090-069-A HLX-504 (DVD-SL) (NTSC) : PART No. J-6090-088-A HLX-506 (DVD-SL) (PAL) : PART No. J-6090-077-A HLX-501 (DVD-DL) (NTSL) : PART No. J-6090-071-A HLX-505 (DVD-DL) (NTSC) : PART No. J-6090-089-A HLX-507 (DVD-DL) (PAL) : PART No. J-6090-078-A Note: Do not use excepting test disc for DVD. ADJUSTMENT AFTER OPTICAL PICK-UP BLOCK REPLACED After optical pick-up block is replaced, adjustment is necessary. In this case, perform “EXECUTING IOP MEASUREMENT” (Refer to page 19 in TEST MODE) next. RFMON LEVEL CHECK Connection : Procedure : 1. Connect an oscilloscope to CN105 pin 6 (RFMON) and CN105 pin 3 (GND) on the DMB15 board. 2. Press the I/1 button to turn the power on, and press the Z OPEN/CLOSE button to open the CD disc table. 3. Set the test disc (DVD-SL (NTSC): HLX-503 (Part No. J- 6090-069-A, CD: YEDS-18 (Part No. 3-702-101-01) on the tray and press the Y button to playback. 4. Confirm that oscilloscope waveform is clear and check RFMON signal level is correct or not. Note: A clear RFMON signal waveform means that the shape “◊” can be clearly distinguished at the center of the waveform. + – DMB15 board CN105 pin 6 (RFMON) CN105 pin 3 (GND) oscilloscope VOLT/DIV: 200 mV TIME/DIV: 500 ns level: 0.58 ± 1.23 Vp-p (DVD-SL) 0.57 ± 1.1 Vp-p (CD) IC102 – DMB15 Board (Side A) – IC201 CN105 1 6 RECORD/PLAYBACK HEAD AZIMUTH ADJUSTMENT DECK A DECK B Note : Perform this adjustment for both decks. Procedure: 1. Mode: Playback 2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak. 3. Mode: Playback MAIN board CN510 test tape P-4-A100 (10 kHz, –10 dB) pin 3 oscilloscope L-CH R-CH V H waveform of oscilloscope in phase 45° 90° 135° 180° good wrong pin 2 pin 1 L R Screw position L-CH peak within 1dB Output level L-CH peak R-CH peak within 1dB Screw position R-CH peak SECTION 6 ELECTRICAL ADJUSTMENTS 0 dB=0.775 V DECK SECTION 1. Demagnetize the record/playback head with a head demagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. 3. After the adjustments, apply suitable locking compound to the parts adjust. TEST TAPE Tape Signal Used for P-4-A100 10 kHz, -10 dB Azimuth Adjustment set MAIN board CN510 pin 1 (L-CH) pin 3 (R-CH) MAIN board CN510 pin 2 (GND) + – level meter test tape P-4-A100 (10 kHz, –10 dB) 4. After the adjustments, apply suitable locking compound to the pats adjusted. Adjustment Location: Playback Head (DECK-A) Record/Playback/Erase Head (DECK-B) reverse forward Connecting Location: Ver. 1.2

DQ0 – DQ7 AD0 – AD7 A-1, A0 – A20 IOA0 – IOA21 D/A CONVERTER IC301 OPTICAL PICK-UP BLOCK RF AMP, SERVO DSP, MPEG DECODER IC102 FOCUS/TRACKING COIL DRIVE, SPINDLE/SLED MOTOR DRIVE IC201 AUTOMATIC POWER CONTROL (FOR CD) Q102-1 DVDRFIP 6 MA 8 MB 9 MC 10 MD 11 RF DVDA 2 SDTI1 14 DVDB 3 DVDC 4 DVDD 5 VOA/A VOB/B VOC/C VOD/D TNI 18 VOE/E+G TPI 19 VOF/F+H V2O 29 VC LDO1 23 LD (780) AUTOMATIC POWER CONTROL (FOR DVD) Q102-2 LDO2 22 LD (650) FOO 42 CD ON SWITCH Q101-1 DVD ON SWITCH Q101-2 VR (780) MSW LIMSW 50 VR (650) FCS+ MSW MDI1 20 MDI2 21 PD 176 LIMIT Q103 IOCS CE SD-RAM IC104 X101 27MHz FL FR B 36 FCS– 37 1 TRO 41 TRK+ 35 TRK– 34 4 FMO 38 SL+ 29 SL– 30 10 DMO 37 SP+ 27 SP– 28 31 32 42 46 47 13 SPFG 47 45 ASDATA0 217 LOUT1+ 2 LOUT1– 1 ROUT1+ 48 ROUT1– 47 MCLK ACLK 10 ACLK 215 BICK 9 ABCK 214 LRCK 17 ALRCK 213 SDA 20 SDA 103 SPDATA 209 SCL 19 SCL 102 PDN 8 XRST 220 XTALI 229 VOICE 206 SMSCK 208 XTALO 228 EEPROM IC103 SDA 6 SCL 5 MIX AMP IC3711 SDTI2 15 SL SR ASDATA1 218 LOUT2+ 46 LOUT2– 45 ROUT2+ 44 43 ROUT2– MIX AMP IC3731 SDTI3 16 FC SW ASDATA2 219 LOUT3+ 42 LOUT3– 41 ROUT3+ 40 39 ROUT3– MIX AMP IC3751 SDTI4 13 LT RT ASDATA4 222 LOUT4+ 38 LOUT4– 37 ROUT4+ 33 32 ROUT4– MIX AMP IC3771 FL, FR, SL, SR, FC, SW C LT, RT D ANALOG-L 81 – 84, 86 – 88, 91 29, 31, 33, 35, 38, 40, 42, 44 93, 78, 53 – 59, 75, 74, 72 – 67, 92, 60, 61, 76, 89 45, 25 – 18, 8 – 1, 48, 17, 16, 9, 10 DQ0 – DQ15 RD0 – RD15 A0 – A11 RA0 – RA11 2, 4, 5, 7, 8, 10, 11, 13, 42, 44, 45, 47, 48, 50, 51, 53 125 – 123, 121, 120, 118, 117, 115, 135, 133 – 128, 126 147, 149 – 151, 166 – 164, 162, 160, 159, 146, 158 23 – 26, 29 – 34, 22, 35 77 26 IOOE OE 79 28 IOWR WE 66 11 BA0 BA0 143 20 BA1 BA1 145 21 RCLK CLK 156 38 CKE CKE 157 37 DQM0 LDQM 113 15 DQM1 UDQM 137 39 RAS /RAS 140 18 CAS /CAS 139 17 RCS /CS 142 19 RWE /WE 138 WIDE 49 16 • SIGNAL PATH : CD PLAY : DVD PLAY : AUDIO : VIDEO : Y : CHROMA : COMPONENT VIDEO FOCUS COIL DRIVE TRACKING COIL DRIVE SLED MOTOR DRIVE SPINDLE MOTOR DRIVE REGULATOR MUTE123 MUTE12 211 19 MUTE MUTE34 210 20 TSD_M TSD-M 170 22 IOPMON 40 40 8 MUTE5 21 BUFFER BUFFER RF+3.3V AU+5V REGO2 REGO1 MTK-SOD IFSDO 32 98 MTK-XIFCS IXFCS 24 100 MIC STATUS MIC 21 205 MTK-KMOD KRMOD 22 207 MTK-SIO IFSDI 31 101 MTK-CLK IFCK 33 99 MTK-IFBSY IFBSY 23 105 MTK-RESET PRST 25 VMUTE 88 VIDEO-OUT-SW 87 110 MASTER CONTROLLER IC401 (1/6) CENTER VOLTAGE GENERATOR Q3801 ABCK ALRCK XVOICE SCORE SPDATA 196 YUV2 194 YUV1 198 YUV3 202 YUV5 200 YUV4 203 YUV6 VIDEO AMP, 75Ω DRIVER IC801 4 CVBSIN 2 CIN 6 YIN 10 CYIN 12 CBIN 14 CRIN 3 MUTE1 13 MUTE2 25 S1 : DIGITAL OUT : VIDEO INPUT (VIDEO) • R-ch is omitted due to same as L-ch. KHM-310CAB OR KHM-313CAB VIDEO OUT J802 S VIDEO OUT J801 VIDEO SWITCH, 75Ω DRIVER IC800 2 SW1 J800 COMPONENT VIDEO OUT Y PB/CB PR/CR 1 VIN1 3 VIN2 23 CVBSOUT 7 VOUT 26 C OUT 21 YOUT 20 CYOUT 18 CBOUT 16 CROUT 27 S-DCOUT J1102 (1/2) VIDEO INPUT VIDEO C Y FLASH ROM IC101 DISC TABLE ADDRESS SENSOR IC731 LOADING MOTOR DRIVE IC701 M751 (LOADING) 7 FIN 38 LM-F 4 OUT1 2 OUT2 9 FIN 39 LM-R TABLE MOTOR DRIVE IC712 M741 (TABLE) 7 FIN 36 TM-F 4 OUT1 2 OUT2 9 FIN 37 TM-R 27 TBL SENS LEVEL SHIFT Q731 S711 ROTARY ENCODER 35 E1 26 EJECT SW 34 E2 28 E3 M M DISC TABLE ADDRESS DETECT DISC TABLE OPEN/CLOSE DETECT S751 OPEN CLOSE SPDATA A/D CONVERTER IC3601 LIN R-CH ABCK ABCK ALRCK 1 RIN 2 12 DOUT 15 SCKI 11 BCK 10 LRCK A XVOICE, SCORE SECTION 7 DIAGRAMS (Page 24) (Page (Page (Page

E MUSIC L+R RT C LT, RT LT J1100 MIC 1 J1101 MIC 2 MIC AMP IC1101 16 MC2P 15 MC1P POOUT 1 0Y Y COM 4 3Y 13 11 3 D0 D1503 D1504 D1505 COM EFFECTOR-CTR1 57 EFFECTOR-S0 19 MIC-DETECT 85 EFFECTOR-S1 43 EFFECTOR-S2 44 EFFECTOR-S3 45 EFFECTOR-SELECT 18 MASTER CONTROLLER IC401 (2/6) • SIGNAL PATH : MIC INPUT : AUDIO 6 VOL2 MIC 1 LEVEL RV1102 5 VOL1 MIC 2 LEVEL RV1101 7 VOL3 21 MCO ECHO LEVEL RV1100 29 DIGITAL ECHO IC1100 AC/DC CONVERTER IC2000 (1/2) COMPARATOR IC2002 COMPARATOR IC2001 XVOICE SCORE A XVOICE, SCORE F MIC AC/DC CONVERTER IC2000 (2/2) DIGITAL ECHO IC1504 MIXER IC1505 (2/2) SWITCHING Q1505 A+9V SWITCHING Q1504 SWITCHING Q1503 SWITCHING Q1508 12 0X 11 3X DIGITAL ECHO IC1501 MIXER IC1505 (1/2) SWITCHING Q1502 LEVEL SHIFT Q1509, 1510 EFFECTOR-CTR2 63 LEVEL SHIFT Q1511, 1512 EFFECTOR-CTR3 70 LEVEL SHIFT Q1513, 1514 SWITCHING Q1501 SWITCHING Q1500 SWITCHING Q1506 A 10 B 9 C D1506 D1507 D1508 MULTIPLEXER IC1502 11 3 COM A 10 B 9 C MULTIPLEXER IC1503 3 X COM 13 9 A 10 B SIGNAL SELECTOR IC1506 DM_L DM_R G DM_L, DM_R (Page 26) (Page 23) (Page 26) (Page 23) (Page 26)

T301 BIAS OSC BIAS OSC Q370 REC BIAS SWITCH Q378, 380 A+9V R-CH TUNER (FM/AM) AM FM ANT AM ANT ST-L ST-R ST-DOUT/MC-DIN TUNED ST-DIN/MC-DOUT ST-CLK ST-CE FM 75Ω COAXIAL ANTENNA HRPE1 (REC/PB/ERASE) (DECK-B) HP1 (PB) (DECK-A) L-CH L-CH R-CH R-CH R-CH R-CH ERASE R-CH MUTING Q325 MUTING CONTROL SWITCH Q382, 383 R-CH MUTING Q321, 322 MUTING CONTROL SWITCH Q377, 379, 381 32 34 21 24 EQ 28 14 13 11 15 27 26 DECK A/B SELECT SWITCH, REC/PB EQ AMP IC301 CAPM+ M TAPE MECHANISM DECK BLOCK ATRGM+ AHALF BHALF A SHUT B SHUT REC (FWD) REC (REV) (DECK-A) BTRGM+ (DECK-B) (CAPSTAN/REEL) 6 ST-CE 3 ST-CLK 2 ST-DOUT 5 ST-DIN 1 TUNED 71 TC-MUTE 54 REC MUTE 53 TC-RELAY 52 REC BIAS 47 A-HALF 91 B-HALF 89 A-SHUT 90 B-SHUT 48 A-TRIG 49 B-TRIG 50 CAPM H ST-L K REC-L J TC-L MUTING Q106 R-CH MUTING CONTROL SWITCH Q509, 510 TRIGGER PLUNGER DRIVE (DECK-A) Q340, 343 TRIGGER PLUNGER DRIVE (DECK-B) Q342, 345 CAPSTAN/REEL MOTOR DRIVE Q341, 344 MASTER CONTROLLER IC401 (3/6) • SIGNAL PATH : TAPE PLAY (DECK-B) : REC : TAPE PLAY (DECK-A) : TUNER (FM/AM) • R-ch is omitted due to same as L-ch. AIN1 REC-OUT1 REC-IN1 EQ-OUT1 REC MUTE ON/OFF 56 ALC ALC ON/OFF 55 PB A/B A/B MUTE ON/OFF TAI1 PB-OUT1 BIN1 (Page 26) (Page 26) (Page 26)

SR, FC, SW J TC-L F MIC DM_R FL FR DM_L SR FC SW SL MUTING Q202 MUTING Q252 MUTING Q200 MUTING Q250 37 40 41 2 6 33 34 5 10 9 8 7 4 23 14 24 22 39 38 R-CH R-CH + 15 AUTO GAIN CONTROL R-CH 27 3 31 30 5 3 H ST-L R-CH J201 TV/SAT AUDIO IN L R 4 J1102 (2/2) R-CH VIDEO INPUT AUDIO L R SELECTOR TONE 6 14 15 18 + 7 2 42 8 + R-CH + R-CH BASS BOOST 24 17 16 MUTING CONTROL SWITCH Q507, 508 77 DVD-A-MUTE VOL-IC-DATA I/F 17 81 VOL-IC-CLK 18 82 AUDIO-IC-DATA 79 AUDIO-IC-CLK AUDIO-OUT-SW 80 FEED BACK SWITCH Q205 R-CH R-CH 28 MUTING Q117 FEED BACK SWITCH Q101 R-CH R-CH IN-MUTE OUT-MUTE I/F MCU 22 21 83 ANALOG-IN-MUTE OUT-MUTE IN-MUTE 46 LINE-MUTE 76 SW-MUTE 75 MUTING CONTROL SWITCH Q516, 517 MUTING Q206 SPEANA AMP IC304 (2/2) BUFFER IC304 (1/2) MUTING CONTROL SWITCH Q521, 522 MUTING Q514, 564 MUTING CONTROL SWITCH Q505, 506 MUTING Q750 MUTING Q700 MUTING Q740 MUTING Q810 MUTING Q208 MUTING Q207 MUTING CONTROL SWITCH Q512, 515, 519 MUTING CONTROL SWITCH Q511 J203 SUBWOFFER OUT R-CH FL, FR, SL, SR, CTR N MUSIC L+R E REC-L K SPEANA L SW P AC4 Q SW-MUTE S DBFB F/B ANALOG-L M D FL FR SL SR CTR 29 26 25 13 11 12 J202 R-CH J103 AUDIO OUT D-LIGHT SYNC OUT L R MASTER CONTROLLER IC401 (4/6) INPUT SELECT SWITCH,TONE CONTROL, ELECTRICAL VOLUME, BASS BOOST AMP IC101 ELECTRICAL VOLUME IC201 • SIGNAL PATH : REC : AUDIO OUT : TV/SAT AUDIO IN : MIC INPUT : TAPE PLAY : TUNER (FM/AM) : AUDIO • R-ch is omitted due to same as L-ch. : VIDEO INPUT (AUDIO) SAT-L ST-L TC-L VOLIN1 DVD-L MIC SUR1 DATA CLOCK TOUT1 SWOUT OUT1 BB_A1 BB_B1 RECB1 VIDEO-L (ZX100D) (ZX80D) (ZX100D) (ZX80D) (ZX100D) FEED BACK SWITCH Q255 D511 D510 + 7-4. BLOCK DIAGRAM – AUDIO SECTION – (Page 25) (Page 25) (Page 24) (Page 24) (Page 23) (Page 28) (Page 26) (Page 23) (Page 27) (Page 24) (Page 27) (Page 27) (Page 28) (Page 27)

N FL, FR, SL, SR, CTR M DBFB F/B P SW FR FL SL SR CTR POWER AMP IC600 18 11 14 8 12 POWER AMP IC702 18 11 14 8 19 21 STANDBY SWITCH Q604, 606, 610 STANDBY SWITCH Q720 – 722 + + + + + + DC DET 2 1 4 3 OVER LOAD OVER CURRENT PROTECTOR IC550 OVER LOAD DETECT Q618, 668 OVER LOAD DETECT Q730, 780 OVER LOAD DETECT Q800, 850 OVER LOAD DETECT Q770 THERMAL DETECT Q628, 630 TH629 TH630 D624 MUTING Q640, 641 MUTING CONTROL SWITCH Q634, 682 FAN MOTOR CONTROL SWITCH Q587, 589 FAN MOTOR SWITCH Q588 D550 RY646 RELAY DRIVE Q644 PROTECT SWITCH Q647 OVER LOAD DETECT Q648 –1 –2 RY760 RELAY DRIVE Q763 PROTECT SWITCH Q765 RY761 RELAY DRIVE Q762 –1 –2 J1103 PHONES TM600 + – – + L R + – – + + – D655 D654 + + D764 D763 D765 AC CUT DETECT R M502 (FAN) M FRONT SPEAKE TM700 TM701 L R SURR SPEAKE CENTER SPEAKER + – TM101 SUBWOOFER OUT CN102 SYSTEM CONTROL MASTER CONTROLLER IC401 (5/6) PROTECT 67 STK-MUTE 60 CTR-RELAY 65 SW-SPK RELAY 51 REAR-RELAY 61 FR-RELAY 66 UNDER VOLTAGE 69 HP-DETECT 84 THERMAL VACS 94 HP-MUTE 72 FAN HI SPEED 58 FAN CONTROL 42 RY862 RELAY DRIVE Q814 PROTECT SWITCH Q815 –1 –2 • SIGNAL PATH : AUDIO AC CUT DETECT Q504 Except US, Mexican CT OUT OCP VP (ZX100D) (ZX100D) (ZX100D) (ZX100 (ZX80D) (ZX80D) (ZX100D) (ZX80D) (ZX100D) (ZX100D) S SW-MUTE (ZX80D) POWER AMP IC800 11 4 15 6 13 12 STANDBY SWITCH Q812 D812 UNREG B+ FAN MOTOR CONTROL SWITCH Q581, 582 FAN MOTOR CONTROL SWITCH Q578 FAN MOTOR SPEED CONTROL SWITCH Q579 FAN MOTOR SWITCH Q585 M501 (FAN) M UNREG B+ D582 D581 TO SS-WGV100D SW-LEVEL-IN 95 SW-LED 100 (Page 26) (Page 26) (Page 26) (Page (Page 26) Ver. 1.1

VOLTAGE SELECTOR S1200 RESET SIGNAL GENERATOR IC501 RESET SWITCH Q501 VF VF AC2 AC2 VP STBY-LED 41 SIRCS REMOTE CONTROL RECEIVER IC903 4 15 X402 5MHz X-IN 13 X-OUT 10 X401 32.768kHz XC-IN 11 XC-OUT 83 X901 4MHz XIN 82 XOUT POWER ON/OFF RELAY DRIVE Q1200 POWER SWITCHING D1292 –36V REGULATOR Q1264 F1261 F1271 RECT D658 +VL –VL AC1 AC1 F1241 F1251 RECT D656 +VH –VH AC4 AC4 F1291 RECT D561 AC3 AC3 F1281 RECT D560 VF1 VF2 VP (–36V) D660 D661 TO FLUORESCENT INDICATOR TUBE FL901 +3.3V REGULATOR IC559 +9V REGULATOR IC507 +9V REGULATOR IC561 +9V REGULATOR IC560 B+ SWITCH Q513, 520 M+9V, LED+9V SW+9V AU+5V A+9V +5V REGULATOR Q103 +3.3V SW+3.3V SW+5V RF+1.8V RF+3.3V +3.3V REGULATOR IC105 +3.3V REGULATOR IC107 OVER VOLTAGE DETECT Q550 RGRULATOR CONTROL SWITCH Q503, 518 UNREG B+ D551 RGRULATOR CONTROL SWITCH Q104 78 MTK- POWER 68 OVER VOLTAGE 20 AC-CUT 7 STBY-RELAY 12 RESET EVER+4V D504 B+ SWITCH Q523, 524 D+3.3V EVER+3.3V D505 D585, 586 D+4V +4V REGULATOR Q323 +5.6V +5.6V REGULATOR Q1507 D101, 102 LED DRIVE Q903 LED DRIVE Q917 74 POWER-KEY S927 I / 1 73 DISPLAY-KEY 29 61 IIC-CLK S928 DISPLAY I2C-CLOCK 30 60 IIC-DATA I2C-DATA 80 LED SELECTOR 40 77 GC-RESET RESET SPEANA L ROTARY ENCODER S970 VOLUME 74 MASTER VOLUME ROTARY ENCODER S1040 X-JOG-ROUND 73 X-ROUND JOG ROTARY ENCODER S1161 OPERATION DIAL 72 OPERATION DIAL FL901 FLUORESCENT INDICATOR TUBE G1 – G13, G17 – G24 8 – 1, 100 – 96, 92 – 85 P1 – P36 9, 10, 12– 22, 24 – 41, 43 – 47 93 – 95 G14 – G16 GRID DRIVE Q901, 902, 914 KEY 0 – KEY 2 S900 – 925, S1041 – 1047, 1049 (FRONT & TOP PANEL KEY) 64 – 66 MASTER CONTROLLER IC401 (6/6) 52 – 59, 75, 76, 78, 79 LED-CD/DVD, TUNER, LED-TAPE, TV/SAT, LED-VIDEO, (PAUSE, STOP), LED- (AMS+, AMS–), (FF, FR), LED-VOLUME 1, 2, LED-VOLUME 3, 4, LED-VOLUME 5, 6, LED-VOLUME 7, 8, LED- (BEAT JUMP, BEAT MAX), LED- (BALANCE, WAVE, FADER, RANDOM), DELAY, LED-FLANGER, CHORUS, LED-PLAY D908 – 911, 913 – 917, D919 – 926, 929, 930, D1016, 1017, 1020, 1040, D1042, 1044, 1046, 1048, D1050, 1052, 1054, 1056, D1058, 1145, 1153 LED DRIVE Q908 – 913, 915, 918 – 921, 1041 LED ON/OFF CONTROL SWITCH Q906 LED ON/OFF CONTROL SWITCH Q907 B+ SWITCH Q904 B+ SWITCH Q905 SEL A B+ SEL B B+ LED+9V DISPLAY CONTROLLER IC902 IN1 1 IN2 2 BPF2IN1 4 BPF2IN2 5 3 BUF1OUT 15 BPF3OUT 14 BPF2OUT 13 BPF1OUT 16 BPF4OUT 17 RECOUT 67 ALL-BAND BPF1IN1 BPF1IN2 19 18 20 BUF2OUT BPF3IN1 6 BPF3IN2 7 BPF4IN1 8 BPF4IN2 9 REC 68 BF4 BPF4 69 BF3 BPF3 70 BF2 BPF2 71 BF1 BPF1 REC BPF4 BPF1 BPF2 BPF3 BAND-PASS FILTER IC904 AC CUT DETECT R D507 D506 AC4 Q RY1200 T1200 POWER TRANSFORMER (Except US, Mexican) D927 (RED) I / 1 D928 (GRN) I / 1 +1.8V REGULATOR IC106 +5V REGULATOR IC558 M+9V 7-6. BLOCK DIAGRAM – PANEL/POWER SUPPLY SECTION – (Page 26) (Page 27) (Page 26) Ver. 1.1

C B These are omitted. E Q Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • f : internal component. • 2 : nonflammable resistor. • 5 : fusible resistor. • C : panel designation. • A : B+ Line. • B : B– Line. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. – DMB15/VIDEO Boards – no mark : DVD PLAY ∗ : Impossible to measure – Other Boards – no mark : TUNER (FM/AM) ( ) : DVD PLAY 〈〈 〉〉: TAPE PLAY (DECK-A) { } : REC ∗ : Impossible to measure • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal produc- tion tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal produc- tion tolerances. • Circled numbers refer to waveforms. • Signal path. J : CD PLAY c : DVD PLAY I : DIGITAL OUT F : AUDIO L : VIDEO E : Y a : CHROMA r : COMPONENT VIDEO f : TUNER (FM/AM) j : TAPE PLAY (DECK-A) d : TAPE PLAY (DECK-B) G : REC k : TV/SAT AUDIO IN h : AUDIO OUT N : MIC INPUT g : VIDEO INPUT (AUDIO) p : VIDEO INPUT (VIDEO) • Abbreviation E2 : 120V AC area in E model E3 : 240V AC area in E model E13 : Russian model and 220V – 230V AC area in E model E51 : Chilean and Peruvian models MX : Mexican model MY : Malaysia model SP : Singapore model • Circuit Boards Location Note on Printed Wiring Board: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • f : internal component. • : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) • DMB15 board is multi-layer printed board. However, the patterns of intermediate layers have not been included in diagrams. • Indication of transistor Caution: Pattern face side: Parts on the pattern face side seen from (Side B) the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Side A) the parts face are indicated. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. B These are omitted. C E Q MOTOR (LD) board CD-SW board JOG board X-ROUND board SW board VIDEO board SENSOR board DMB15 board MOTOR (TB) board TUNER (FM/AM) KARAOKE board DRIVER board PANEL board FUNCTION board MIC board POWER SWITCHING EFFECTOR board MAIN board PRIMARY board TRANS board SURROUND board PA board

• See page 29 for Circuit Boards Location. : Uses unleaded solder. New part of EEPROM (IC103) on the DMB15 board cannot be used. Therefore, if the mounted DMB15 board is replaced, exchange new EEPROM with that used before the replacement. R3607 L3602 FB115 FB114 FB113 FB112 CN302 R3653 R3805 R319 Q103 R116 R117 C224 R136 R142 FL101 C222 C221 R153 R155 C220 C219 FL107 FL403 C218 RB107 RB108 RB113 CN101 RB112 C3804 Q3801 C215 C3802 R3803 R3804 FL401 C3803 C3805 C210 X101 R208 C208 CN105 CN106 CN201 CN401 R209 C206 C205 R210 R214 FB401 FB402 FB403 FB404 D1001 FB405 FB406 R215 R216 R219 R224 FL402 C190 R233 R234 C180 C179 R161 R107 R101 R1527 C306 C102 C105 C402 C108 R189 C307 C305 R190 R191 C302 R192 R193 C153 C152 R1101 C117 R1102 R1105 R1108 R3651 R1553 C138 C137 C135 R1129 C133 C132 R1168 C119 C118 C116 R195 C112 C101 R197 C167 C170 C181 C217 C189 C177 R1544 C403 C129 R152 C3783 R1550 R1549 C3782 C3781 C3774 C3773 C3772 C3771 C3707 R3782 R3781 R4706 R4705 R1543 C3784 R3773 R3774 R3775 R3776 R3777 R3772 R3771 R3768 R3767 R3766 R3765 R3764 R3763 R3758 R3757 R3778 R3783 R3756 R3784 R3785 R3786 R3755 R3754 R3753 C3764 R3787 C3763 C3762 C3761 C3754 C3801 R3788 C3753 C3752 C3751 C3705 R3762 R3761 R3802 R3801 C178 R3716 R3752 R3717 R3715 R3751 R3748 R3747 R3746 R3714 R3745 R3744 R3743 R3738 R3713 R3737 R3736 R3735 R3734 R3733 C3744 R3718 R3721 R3722 R3723 C3743 C3742 C3741 C3734 R3712 R3711 R3724 R3725 C3733 C3732 C3731 C3703 D3502 D3501 C150 C3724 C3723 C3722 C3721 C3714 R3742 CN301 R3741 C3713 C3712 C3711 R3732 R3731 C3701 C187 C3606 C3605 C3603 R3728 R3727 R3726 R3603 R1557 R1559 C3608 C3609 IC102 IC201 IC104 IC103 IC101 IC106 DMB15 BOARD (SIDE A) 1-869-463- 11 E 1 5 E 1 2 20 21 (FOR CHECK) OPTICAL PICK-UP BLOCK KHM-310CAB OR KHM-313CAB B MAIN BOARD NO523 A MAIN BOARD CN520 D MAIN BOARD CN521 C VIDEO BOARD CN801 A B C D E F G H 1 2 3 4 5 6 7 8 9 • Semiconductor Location Ref. No. Location D1001 E-3 D3501 H-5 D3502 H-5 IC101 C-7 IC102 E-6 IC103 E-4 IC104 E-4 IC106 E-3 IC201 C-4 Q103 F-8 Q3801 G-5 (Page 45) (Page 45) (Page 45) (Page 38)

1-869-463- 11 1 3 5 4 1C 1B 2E 1E 2B 2C 1D 5 4 1 3 2G 2S 1S 1G 2D (ZX100D:SP, MY) (ZX80D:E3, E13/ZX100D:E3) (ZX80D:US, E2, E51, MX/ZX100D:E2, E51, MX) B A C D E F G H 1 2 3 4 5 6 7 8 9 7-8. PRINTED WIRING BOARD – DMB15 Board (Side B) – • See page 29 for Circuit Boards Location. : Uses unleaded solder. • Semiconductor Location Ref. No. Location D3601 H-8 D3602 G-7 IC105 C-3 IC107 F-3 IC301 F-7 IC3601 G-8 IC3711 H-7 IC3731 G-7 IC3751 G-6 IC3771 H-6 Q101 E-2 Q102 E-2 Ver. 1.1

• See page 67 for IC Block Diagrams. New part of EEPROM (IC103) on the DMB15 board cannot be used. Therefore, if the mounted DMB15 board is replaced, exchange new EEPROM with that used before the replacement. C105 RB105 RB106 R124 FB111 FB112 FB113 FB114 FB115 C109 C101 R111 R117 R107 R114 R1129 R109 R110 R112 R113 R115 Q102 R118 R120 R121 C113 C112 C195 R126 C192 CN105 C193 R1151 R1152 R1150 C108 C167 R1110 R193 C102 R104 C189 C187 R1134 FL107 R187 C184 C182 R1133 R169 C191 C180 C179 C181 FL108 C106 R191 C178 R108 R101 IC107 FL101 Q103 IC103 R123 IC105 IC106 C190 IC101 C188 R1502 R1544 CN106 CN101 R106 R105 D1001 Q101 R116 IC104 R1546 47 6.3V 47 47 47k 0.001 0.01 100 47k 10k 100k 100k 0 47k 22 22 22 QST8TR 22 22 22 0.01 47 6.3V 0.22 0 0.01 6P 0.22 3.3k 3.3k 3.3k 0.001 0.01 2.7k 1k 1 0 0.33 47 4V 0 0 0.01 0.22 0 10k 0.1 0.1 0.1 0.1 0.01 1k 47 4V 1M 100 TK11133CSCL-G DTC124EKA- T146 BR24L64F-WE2 0 TK11133CSCL-G PQ018EN01ZPH 47 6.3V 0.22 0 0 13P 24P 10k 10k RB501V-40TE-17 UM6K1N-TN 1k A2V64S40CTP-G75 3.3k A4 A5 A6 A12 A9 A8 A11 A10 A7 A1 A2 A3 REG01 GND SW+5V SW+3.3V TRK- TRK+ FCS+ FCS- IOP MSW V2REFO SDA REG02 MREQ MIC KRMOD IFSDO IFCK XIFCS IFSDI SCL IFBSY RXD TXD PRST RF VC PD LDO1 RF1.8 LDO2 RF+3.3V VOA VOB VOC VOD VOE VOF RA4 RA5 RA6 RA7 RA8 RA9 RA11 DRCKE DRCLK DQM1 RD0 RD1 RD2 RD3 RD4 RD5 RD6 RD7 DQM0 RWE CAS RAS RCS BA0 BA1 RA10 RA0 RA1 RA2 RA3 RD8 RD9 RD10 RD11 RD12 RD13 RD14 RD15 DVD_LD CD_LD DVD_LD CD_LD RFMON SCL SDA A16 A15 A14 A13 A12 A11 A10 A9 A20 A21 A19 A18 A8 A7 A6 A5 A4 A3 A2 A17 A0 A1 XRD XROMCS XWR HD0 HD1 HD2 HD3 HD4 HD5 HD6 HD7 MSW LDO1 MREQ MIC KRMOD RFMON V2REFO RXD TXD PRST XIFCS IFBSY IFSDI IFSDO IFCK RF FCS- FCS+ TRK+ TRK- PD MSW VC IOP LDO2 PRST LDO1 TXD IFBSY SDA SCL IDSDI XIFCS IFCK IFSDO MREQ MIC KRMOD V2REFO VOA VOB VOC VOD VOE VOF PD VOE VC VOF VOB VOA RF VOD VOC TRK- TRK+ FCS+ FCS- RXD IOP LDO2 TXD RXD GND +3.3V RFMON V2REFO A0 A1 A2 GND VCC SCL SDA A15 A14 A13 A12 A11 A10 A9 A8 A19 WE RESET N.C. N.C. RY/BY A18 A17 A7 A6 A5 A4 A3 A2 A1 A16 BYTE VSS DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE VSS CE A0 RF VOB/B VOC/C VOD/D VOA/A VOF/F+H VC VCC VOE/E+G NC TRK- FCS- TRK+ FCS+ PD NC S S NC SYSRST XIFCS IFBSY SIO SCO GND (LD) LD (650) LD (780) VR (650) VR (780) GND (PDIC) (LO:DVD.HI:CD)MSW MIC KRMOD CONT GND NOISE VIN VOUT NOISE GND CONT VOUT VIN +3.3V REGULATOR -1 -2 INVERTER Q101-1 CD ON SWITCH Q101-2 DVD ON SWITCH EEPROM Q102-1 Q102-2 AUTOMATIC POWER CONTROL(FOR CD) AUTOMATIC POWER CONTROL(FOR DVD) SD-RAM VSS A4 A5 A6 A7 A8 A9 A11 NC CKE CLK UDQM NC VSS DQ8 VDDQ DQ9 DQ10 VSSQ DQ11 DQ12 VDDQ DQ13 DQ14 VSSQ DQ15 VSS VDDB A3 A2 A1 A0 A10 BA1 BA0 LDQM VDD DQ7 DQ4 DQ3 VSSQ DQ2 DQ1 VDDQ DQ0 VDD VSSQ VDDQ DQ6 DQ5 +3.3V REGULATOR +1.8V REGULATOR VOUT CONT VIN NC GND A-1 FLASH ROM OCSW1 3.3VMNT SOO M-REQ DGND VOICE (1/4) /CS /RAS /CAS /WE A20 MX29LV320CBTC70-CBA3-0604CE (ZX80D:E3,E13/ZX100D:E3) MX29LV320CBTC70-CBA3-0604GA (ZX100D:SP,MY) MX29LV320CBTC70-CBA3-0604UC (ZX80D:US,E2,E51/ZX100D:E2,E51) S29AL032D70TF-CBA3-0601UC (ZX80D:MX/ZX100D:MX) (FOR CHECK) -2-1 WP (Page 34) (Page 33) (Page 46) (Page 33) (Page 34) (Page 34) (Page 33) (Page 34) Ver. 1.1

R233 C213 R214 C205 R208 R215 C206 R216 R213 C208 R205 R209 C203 R207 R204 C214 C212 C233 R230 R221 C209 C211 R226 R231 R232 R234 R225 R223 R220 R212 R219 R224 C210 C217 C218 C219 C220 C224 C221 C222 R246 IC201 C402 FL401 FL402 FB401 FB402 FB403 FB404 FB405 FB406 FL403 CN401 R247 CN201 C215 R2504 C403 R5008 R5011 R5014 R5016 R5017 R206 R210 33k 0.01 15k 220p 33k 12k 220p 12k 6.8k 0.01 10k 33k 0.01 2.7k 1.2k 0.001 0.01 0.0047 82k 56k 0.033 0.033 56k 15k 18k 10k 100k 100k 10k 10k 27k 10k 0.01 47 16V 10 16V 0.01 10 16V 0.01 0.1 0.1 4.7k FAN8036L 47 16V 5P 1k 6P 0.01 4.7k 47 6.3V 0 0 0 0 0 10k 47k GND REG02 REG01 MUTE123 MUTE TSD_M SW+3.3V LIMITSW FCS- FCS+ TRK+ TRK- IOP IOPMON VREFO SPFG FOO TRO FMO DMO RF+3.3V SW+5V SW+3.3V GND SW+5V SP+ SP- SL+ SL- SP- SP+ SL- SL+ VREFO SPFG FOO TRO FMO MUTE123 DMO MUTE TSD_M IOP IOPMON LIMITSW TRK- TRK+ FCS+ FCS- IOPMON VREFO SPFG FOO TRO FMO MUTE123 DMO MUTE TSD_M FCS- FCS+ TRK+ TRK- IOP LIMITSW SP- SP+ LIMIT (GND)LIMIT SL- SL+ SW+5V SW+3.3V MGND SW+9V FOCUS/TRACKING COIL DRIVE, SPINDLE/SLED MOTOR DRIVE (2/4) ZX80D:US,E2,E51,MX/ ZX100D:E2,E51,MX (ZX80D:E3,E13/ZX100D:E3) (ZX100D:SP,MY) DGND (Page 32) (Page 32) (Page 34) (Page 51) (Page 32) (Page 35) (Page 34) Ver. 1.1

• See page 54 for Waveforms. • See page 71 for IC Pin Function Description. R1108 C129 R1530 R1531 R1557 R146 R151 R152 R153 R155 R160 R161 R164 C120 C121 C122 C123 C133 C138 R141 RB108 RB111 RB107 C154 R142 C151 C128 C125 C126 R127 C127 C196 R1554 R1109 FL105 C131 C136 C144 C155 C158 C162 C164 C160 RB113 RB112 C177 FL106 C116 C118 C130 R136 C132 C135 C137 C139 C140 C146 C149 C150 R1168 R1547 C156 C152 C153 C159 R1540 R1548 R1549 R1550 R1103 R1551 R1104 C161 R138 IC102 R1553 R1101 RB103 R196 FL104 R1125 R1124 R1123 R1122 R1121 R1120 R1524 R1526 R1527 R1559 R1543 R1542 R1102 R192 R190 R189 X101 R1504 C147 C148 C119 C115 C117 C114 R1161 R1126 C124 R321 R4701 R4702 R4703 R4704 R4705 R4706 CN301 R1105 C173 C172 C171 C170 C176 C175 RB104 C174 R197 C163 R195 0 10 16V 0 0 100 47 47 0 47 47 47 100 100 1 1 1 1 0.1 0.001 750k 22 0 22 0.1 100k 0.001 0.0015 0.1 0.1 100 0.01 0.0047 4.7k 0 2.2 0.01 0.01 0.01 0.01 0.01 0.01 0.01 22 22 47 6.3V 0.1 10 16V 0.1 15k 0.1 0.033 0.1 22p 0.1 0.1 0.1 10 16V 470 4.7k 0.01 12p 12p 0.01 4.7k 4.7k 4.7k 4.7k 10k 4.7k 10k 0.01 100k CXD9849R 0 2.2k 0 0 0 0 0 0 0 0 0 0 0 10k 10k 10k 150 150 150 150 27MHz 0.047 0.047 10 16V 0.1 10 16V 0.1 0 10k 1 0 0 0 0 0 0 0 13P 10k 0.01 0.01 0.01 0.01 0.01 0.01 0 0.01 150 0.01 150 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 MSW MUTE123 MUTE LIMITSW ALRCK ASDATA0 ASDATA1 ASDATA2 ASDATA4 XRST VREFO RF+3.3V SPFG IOPMON DMO FMO TRO FOO V2REFO TSD_M SPDATA KRMOD MIC MREQ ABCK ACLK SCORE XVOICE IFSDO IFCK XIFCS IFSDI SCL SDA IFBSY RXD TXD PRST RF VC PD LDO1 LDO2 RF1.8 SCL SDA RF+3.3V VOA VOB VOC VOD VOE VOF RA4 RA5 RA6 RA7 RA8 RA9 RA11 RA0 RA1 RA2 RA3 RA10 BA0 BA1 DRCKE DRCLK RCS RAS CAS RWE DQM1 RD8 RD9 RD10 RD11 RD12 RD0 RD1 RD2 RD3 RD4 RD5 RD6 RD7 DQM0 A2 A3 A4 A5 A6 A7 A8 A18 A19 A0 A1 A9 A10 A11 A12 A13 A14 A15 A16 A17 A20 A21 HD0 HD1 HD2 HD3 HD4 HD5 HD6 HD7 XWR XROMCS XRD RD13 RD14 RD15 ASDATA4 XRST ASDATA0 ASDATA1 ASDATA2 ACLK ABCK ALRCK MUTE123 MUTE SPDATA SCORE KRMOD MIC XVOICE CR/R CB/B Y/G V C Y LIMITSW TSD_M V2REFO VREFO IOPMON SPFG DSEL WIDE MSW IFSDO IFCK XIFCS IFSDI SCL SDA IFBSY RXD TXD PRST MREQ RF VC PD LDO1 LDO2 Y C V Y/G CB/B CR/R XVOICE MIC KRMOD SCORE SPDATA MUTE MUTE123 ALRCK ABCK ACLK ASDATA0 ASDATA1 ASDATA2 ASDATA4 XRST LIMITSW TSD_M V2REFO VREFO IOPMON MSW WIDE DSEL SPFG XIFCS IFSDI PRST SCL SDA IFBSY RXD TXD IFSDO MREQ RF VC PD LDO1 LDO2 VOA VOB VOC VOD VOE VOF DMO FMO TRO FO0 FOO DMO FMO TRO SCL SDA VOF VOE VOD VOC VOB VOA IFCK (3/4) RGBSEL DSEL/DISCXEXT WIDE D-GND D-GND D-GND D-GND V C Y Y/G CR/R CB/B AGND DVDA DVDB DVDC DVDD DVDRFIP DVDRFIN MC MD SA SB SC SD CDFON CDFOP MDI1 LDO2 LDO1 MDI2 SVDD3 CSD RFLVL SGND V2REFO V2O VREFO TEO TEZISLV OPOUT OPIN OPIN DMO FMO TROPENPWM IOPMON TRO FOO DVSS NC NC DVDD3 SPFG DSEL MSW MAMUTE DVDD18 IOA2 IOA3 IOA4 IOA5 IOA6 IOA7 IOA18 IOA19 DVSS APLLCAP APLLVSS VDD3 IOWR DVDD3 IOA20 IOCS IOA1 IOOE DVDD3 AD0 AD1 AD2 AD3 DVSS AD4 AD5 AD6 IOA21 ALE AD7 IOA0 DVSS URD DVDD18 IFSDO IFCK XIFCS SCL SDA TRG-SW IFBSY RXD TXD DVDD3 ICE PRST IR INT0 DQMO MREQ RD7 DVSS RD6 RD5 DVSS RD4 RD3 IFSDI DVDD18 RD2 RD1 RD0 RD15 DVDD3 RD14 RD13 RD12 RD11 RD10 RD9 DVSS RD8 GPIO DQM1 RWE CAS RAS DVDD3 RCS BA0 DVSS RA10 RA0 DVSS RA1 RA2 RA3 DVDD18 NC NC DVDD3 RCLK CKE RA11 RA9 RA8 DVSS RA7 DVSS RA6 RA5 RA4 DVDD3 DISC/X RGB TSD_M NC NC DVDD18 FWD NC LIMSW OCSW CKSW NC NC DVDD3 NC NC NC NC NC NC DAVCC VREF FS YUV0 DAVSS YUV1 DAVDD YUV2 DAVSS YUV3 DAVDD YUV4 DAVSS YUV5 YUV6 DVDD3 SMSCK MUTE MUTE123 DVDD3 ABCK ACLK DVSS ASDATA0 ASDATA1 ASDATA2 XRST DVDD18 ALRCK ASDATA4 DVSS DWIDE SDPIF RFGND18 RFVDD18 XTALO XTALI JITFO JITFN PLLVSS IDAC PLLVDD3 LPFON LPFIP LPFIN LPFOP VDD3 NC VSS NC NC RFVDD3 RFRPDC RFRPAC HRFZC CRTPLP RFGND NC NC OSP RFGC IREF AVDD3 OSN WIDE SPDATA KRMOD VOICE MIC REV BA1 UWR IOA7 MA MB TNI TPI RF AMP,SERVO DSP,MPEG DECODER FEO IOA8 IOA16 IOA15 IOA14 IOA13 IOA12 IOA11 IOA10 IOA9 (Page 32) (Page 33) (Page 32) (Page 39) (Page 33) (Page 35) (Page 32) (Page 32)

• See page 67 for IC Block Diagrams. CN302 R3504 R3505 D3501 D3502 R3789 R3779 R3778 C3774 R3777 R3776 C3773 C3707 R3774 R3773 C3771 R3772 R3771 IC3771 C3784 R3787 R3788 C3782 R3786 C3783 R3785 R3784 R3783 C3781 R3781 R3782 C3708 R3769 R3759 R3758 R3757 C3754 R3756 C3753 C3705 R3755 C3752 R3754 R3753 R3752 R3751 C3706 IC3751 R3768 R3767 C3764 C3762 R3766 C3763 R3765 R3764 R3763 C3761 R3762 R3761 IC3731 R3749 R3739 R3738 R3736 R3737 C3734 C3733 C3703 R3735 C3732 R3734 R3733 R3732 R3731 C3704 R3748 C3744 R3747 R3746 C3743 R3745 C3742 R3743 R3744 C3741 R3741 R3742 R3729 R3719 R3718 C3714 R3716 R3717 C3701 C3713 R3715 C3712 R3714 R3713 R3712 R3711 IC3711 C3702 R3727 C3724 C3722 R3726 C3723 R3725 R3723 R3721 C3721 R3722 C3805 C3803 R3805 R3724 Q3801 R3803 C3802 C3804 R3801 C3801 C307 R3802 R3804 R319 R3611 R3621 C3611 C3621 C3610 C3609 C3608 C3607 L3602 C3605 C3606 C3603 R3607 C3601 C3602 R3603 D3601 D3602 IC3601 R3605 L3601 R3601 R3606 R3602 R3609 R314 R3653 R3652 C301 C306 C305 IC301 C302 R3651 R3728 R3775 C3772 C3751 C3731 C3711 21P 100 100 1SS355TE-17 1SS355TE-17 1k 1k 4.7k 330p 1k 1k 330p 0.1 3.9k 3.9k 1800p 1.5k 1.5k NJM3414AV 330p 1k 4.7k 2200p 1k 330p 4.7k 3.9k 3.9k 1800p 1.5k 1.5k 0.1 1k 1k 4.7k 1k 330p 1k 330p 0.1 4.7k 2200p 3.9k 3.9k 1.5k 1.5k 0.1 NJM3414AV 4.7k 1k 330p 2200p 1k 330p 4.7k 3.9k 3.9k 1800p 1.5k 1.5k NJM3414AV 1k 1k 4.7k 1k 1k 330p 330p 0.1 4.7k 2200p 3.9k 3.9k 1.5k 1.5k 0.1 4.7k 330p 1k 1k 330p 4.7k 2200p 3.9k 3.9k 1800p 1.5k 1.5k 1k 1k 4.7k 330p 1k 1k 0.1 330p 4.7k 2200p 3.9k 3.9k 1.5k 1.5k NJM3414AV 0.1 1k 330p 2200p 1k 330p 4.7k 3.9k 1.5k 1800p 1.5k 47 4V 100 4V 1k 3.9k 2SC2712 10k 10 47 6.3V 0 100 6.3V 100 6.3V 0 18k 0 100 100 1000p 1000p 0.1 10 16V 10 16V 0.1 100µH 47 6.3V 0.1 0.1 0 10 0.1 10k 1SS355TE-17 1SS355TE-17 PCM1803 0 100 0 100 0 100 0 0 0.01 100 6.3V 0.47 AK4358VQ-L 0.47 0 4.7k 4.7k 2200p 1800p 1800p 1800p XRST ASDATA4 ALRCK ASDATA2 ASDATA1 ASDATA0 SDA SCL GND SPDATA SW+3.3V SW+5V ABCK ACLK XVOICE SCORE LOUT1+ LOUT1- ART+ ART- ART- ART+ ALT+ ALT- ROUT3- ROUT3+ LOUT3+ LOUT3- RT FR FL SR SL RT LT SW FC SR SL FR FL XVOICE SCORE R-IN L-IN ROUT1+ ROUT1- LOUT2+ LOUT2- ROUT2+ ROUT2- LOUT3+ LOUT3- ROUT3+ ROUT3- ALT+ ALT- ROUT2- ROUT2+ LOUT2+ LOUT2- ROUT1- ROUT1+ LOUT1+ LOUT1- LT SW FC SPDATA XRST ABCK ACLK ASDATA0 ASDATA1 ASDATA2 ASDATA4 ALRCK SCL SDA XVOICE SCORE XRST ABCK ACLK ASDATA4 ASDATA0 ASDATA1 ASDATA2 ALRCK SDA SCL SPDATA L-IN R-IN DGND RT AGND LT AGND SW(LFE) FC SR SL AGND FR AGND AL AU+5V AGND L-IN AGND R-IN XVOICE SCORE MIX AMP VDD VSS VDD VSS VDD VSS VDD VSS MIX AMP MIX AMP MIX AMP A/D CONVERTER (4/4) D/A CONVERTER MODE1 MODE0 FMT1 FMT0 OSR SCKI VDD DGND DOUT BCK LIN RIN V_REF_1 V_REF_2 VCC AGND BYPASS FSYNC LRCK PDWN ROUT1+ ROUT1- LOUT2+ LOUT2- ROUT2+ ROUT2- LOUT3+ LOUT3- ROUT3+ ROUT3- LOUT4+ LOUT4- LOUT1- LOUT1+ DZF3(L) DZF2(R) DZF1(SUR) CAD0 ACKSN PDN BICK DVDD DVSS MCLK DSDL1 DSDR1 DSDL2 DSDR2 DSDL3 DSDR3 DIF0 ROUT4- ROUT4+ VREFH AVDD AVSS SDTI4 SDTI1 SDTI2 SDTI3 LRCK I2C SCL SDA CAD1 DCLK DSDL4 DSDR4 (DMIXR) (DMIXL) (FL) (FR) (SL) (SR) (FC) (SW) AGND CENTER VOLTAGE GENERATOR 10µH (Page (P 3 (Page

• See page 29 for Circuit Boards Location. : Uses unleaded solder. JW702 JW703 JW704 JW705 JW706 JW707 JW708 JW711 CN705 JW712 JW701 JW709 JW713 JW714 JW710 R736 CN702 R751 C752 CN703 CN704 IC712 R713 Q731 C751 D711 D701 C737 R734 R733 R732 R723 R722 R721 R731 R712 R711 R702 R701 C736 C735 C741 C731 C715 IC701 CN701 CN721 M751 IC731 CN731 CN741 CN742 M741 CN751 S751 1-866-201- 12 (12) 1 2 E DRIVER BOARD F MAIN BOARD CN511 1 9 1 9 1 4 S711 ROTARY ENCODER DISC TABLE ADDRESS DETECT 1 2 M MOTOR (LD) BOARD 1-687-133- 12 (12) (LOADING) 1 2 SENSOR BOARD 1-687-132- 12 (12) E C A K MOTOR (TB) BOARD 1-687-134- 12 (12) 1 3 (TABLE) SW BOARD 1-687-669- 12 (12) 1 2 DISC TABLE OPEN/CLOSE DETECT OPEN CLOSE A B C D E F G H 1 2 3 4 5 6 7 8 9 10 M (Page 45) • Semiconductor Location Ref. No. Location D701 E-7 D711 E-7 IC701 F-7 IC712 F-8 IC731 F-5 Q731 C-9

• See page 67 for IC Block Diagrams. C741 R702 R701 D701 C751 R713 R712 R711 D711 CN721 R722 R721 R723 C736 C735 C737 R731 C731 R733 CN704 E3 E2 E1 CN703 CN742 CN702 CN741 IC731 CN751 CN705 C752 R751 CN731 Q731 M751 M741 IC701 IC712 R734 R732 CN701 C715 R736 S751 0.01 100 470 MTZJ-T-77 5.1A 0.01 22k 4.7k 1k MTZJ-T-77 3.6B 2P 4.7k 4.7k 4.7k 0.1 0.1 0.1 100 10 50V 1k 2P 4P 5P 5P 3P RPI-579N1 2P 2P 0.1 4.7k 3P DTC114ESA BA6956AN BA6956AN 12k 10k 13P 100 16V 390 RNF RNF TM-2 GND TM-1 SENS-IN SENS-OUT GND TM-1 TM-2 SENS-IN SENS-OUT GND SENS-IN SENS-OUT GND SENS-IN SENS-OUT GND GND OPEN SW OPEN SW LM-2 LM-1 LM-1 LM-2 GND E-1 E-2 E-3 VCC OUT2 GND VREF OUT1 VM FIN RIN VCC OUT2 GND VREF OUT1 VM FIN RIN LM-R TM-R E-1 E-2 E-3 TBL ADDRESS SENS OPEN SW (LOADING) ADDRESS DETECT (TABLE) OPEN CLOSE OPEN/CLOSE DETECT DRIVE LOADING MOTOR DRIVE TABLE MOTOR LEVEL SHIFT D+3.3V M+9V M-GND M-GND LM-F TM-F DISC TABLE S711 DISC TABLE DISC TABLE ADDRESS SENSOR ROTARY ENCODER (Page 46) Ver. 1.1

• See page 29 for Circuit Boards Location. : Uses unleaded solder. JR802 R800 R802 R803 R804 R805 R806 R807 R808 R809 R810 R812 R813 R814 FB800 FB801 FB802 FB803 FB804 FB805 FB806 JR800 JR803 JR804 C818 C817 C816 C819 C820 C821 C822 C823 C824 C825 C831 C809 C804 C810 JW801 JW802 JW804 JW805 JW807 JW811 JW803 JW806 JW800 CN800 EPT800 C811 C812 C813 C814 C815 C800 C801 C802 C803 C805 C806 C807 C808 C829 CN802 L801 C830 CN801 C826 C827 IC800 IC801 14 15 1 28 1 2 VIDEO BOARD 1 5 1-865-440- 11 (13) 1 4 8 5 Y PB/CB PR/CR VIDEO OUT J802 S VIDEO OUT J801 (CHASSIS) (CHASSIS) Y C G G (CHASSIS) E MAIN BOARD NO503 C DMB15 BOARD CN301 T MIC BOARD NO1100 COMPONENT VIDEO OUT J800 (CHASSIS) A B C D E 1 2 3 4 5 6 7 (Page 30) (Page 45) (Page 40)

• See page 54 for IC Waveforms. PR/CR PB/CB C827 L801 10µH R807 C800 C801 C802 C803 C804 C805 C806 C807 C808 R812 R809 C810 C815 C814 C813 C812 C811 R802 R803 R804 R805 R806 R808 C830 C831 R813 C816 C817 C818 C819 C820 C821 C822 CN802 CN800 CN801 C824 C823 C825 EPT800 J802 JR804 J801 FB800 FB801 FB802 FB803 FB804 FB805 JW800 IC801 VIDEO AMP, 75Ω DRIVER IC800 C826 C829 JR800 C809 JR802 J800 JR803 R810 FB806 R800 R814 10 50V 100 1 50V 1 50V 1 50V 22 50V 0.1 1 50V 1 50V 1 50V 100 10V 1M 10k 0.1 1000 6.3V 1000 6.3V 1000 6.3V 1000 6.3V 1000 6.3V 75 75 75 75 0 75 100 10V 0.01 100k 22p 22p 22p 0.01 22p 0.01 22p 2P 5P 13P 0.01 22p 0.01 1P 0 0 0 0 0 0 0 MM1623BF NJM2244M 10 50V 1000 6.3V 0 0.1 0 3P 0.01 68 0 100 10k RGBSEL DSEL/DISCXEXT WIDE D-GND Y/G D-GND Y D-GND C D-GND V +9V V MUTE VIDEO OUT SW GND +5V VIDEO-GND VIDEO-SIG (CHASSIS) (CHASSIS) (CHASSIS) Y COMPONENT VIDEO OUT VIDEO OUT OUT S VIDEO GND2 CROUT GND2 CBOUT GND2 CYOUT YOUT GND2 S2 S1 S-DCOUT VCC2 C OUT CVBSOUT CRIN MUTE2 CLP CYIN I/P BIAS GND1 YIN CVBSIN MUTE1 CIN VCC1 CBIN YC MIX VIN1 SW1 VIN2 SW2 GND VOUT VCC VIN3 CB/B CR/R VIDEO SWITCH, 75Ω DRIVER (Page 34) (Page 47) (Page 41)

• See page 29 for Circuit Boards Location. : Uses unleaded solder. R1152 R1156 R1139 C1128 R1113 R1119 C1125 R1138 R1108 R1102 R1110 C1100 R1126 R1103 R1109 C1101 R1132 R1107 R1106 R1105 R1104 C1113 D1102 IC1101 C1104 R1115 R1116 C1103 R1121 C1110 C1109 R1122 R1123 C1124 R1120 FB902 R1137 C1134 R1127 C1135 R1128 R1130 R1131 R1118 C1129 R1124 R1114 FB1100 FB1101 C1142 IC1100 R1147 C1133 C1139 R1140 R1111 C1102 R1100 C1119 J1101 RV1102 RV1100 RV1101 J1100 J1102 J1103 CN1102 C1114 C1115 C1123 C1127 C1106 C1116 C1117 C1107 C1145 C1144 JW1102 JW1106 JW1108 JW1109 JW1110 JW1111 JW1112 JW1113 JW1114 JW1115 JW1116 JW1117 JW1118 JW1119 JW1120 JW1121 JW1122 JW1123 JW1124 JW1125 JW1126 JW1127 JW1128 EPT1103 EPT1104 JW1107 JW1132 JW1134 NO1101 C1112 C1108 C1111 C1121 C1105 JW1101 C1126 JW1133 NO1100 C1136 1 3 1 2 1 4 1 15 30 16 8 5 1 9 MIC BOARD 1-868-673- 11 (13) PHONES R L VIDEO AUDIO MIC 1 MIC 2 MIC 1 LEVEL VIDEO INPUT H MAIN BOARD CN100 T VIDEO BOARD CN802 U PA BOARD NO601 (CHASSIS) (CHASSIS) ECHO LEVEL MIC 2 LEVEL A B C D E 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 (Page 45) (Page 38) (Page 52) Ver. 1.1

• See page 67 for IC Block Diagrams. CN1102 IC1100 C1108 R1152 C1115 C1116 R1107 R1105 R1106 R1104 C1113 C1106 R1137 R1138 R1126 C1104 C1103 D1102 C1123 C1124 R1123 R1120 R1121 R1122 R1156 C1107 C1110 R1103 C1112 R1109 C1101 R1108 R1110 C1100 R1114 R1124 R1113 R1119 C1125 R1111 R1100 C1102 R1132 C1133 C1139 C1119 C1121 R1118 EPT1103 EPT1104 NO1100 C1129 NO1101 JW1102 FB902 C1109 JW1101 C1144 C1145 FB1101 FB1100 C1134 C1105 R1116 R1115 C1114 R1139 R1147 R1140 C1117 R1130 R1131 C1142 C1127 C1126 C1111 R1102 J1100 J1101 J1102 J1103 RV1102 RV1101 RV1100 R1128 R1127 C1135 C1128 IC1101(1/2) IC1101(2/2) 3P TC9488FG 1 50V 1.5k 4.7 50V 47 16V 100 100 100 5.6k 68p 4.7 50V 10k 10k 10k 0.1 0.1 UDZW-TE17-5.1B 47 16V 0.0012 15k 3.9k 6.8k 12k 1.5k 4.7 50V 1 1k 1 50V 10k 0.01 10k 10k 0.01 10k 10k 12k 15k 0.0015 10k 15k 0.0015 0 0.1 0.1 C1136 0.1 47p 0.22 50V 1k 2P 0.1 9P 0.0047 10 50V 10 50V 0 0 220p 0.1 50V 330 330 4.7 50V 10k 15k 10k 47 16V 15k 15k 0.1 10 50V 220 10V 0.22 50V 1k 3P 50k 50k 50k 33k 33k 220p 47p NJM4565M NJM4565M MIC AGND A+9V H/P DETECT VIDEO-SIG VIDEO-GND MIC ECHO NC OSCR OSCC VDD NC NC VRO VREF VDA ALC1 MC1N MC1P VSS POOUT TEST VOLST NC DA OUT NC ADIN PRIN MCO VSA ALC2 NC MC2N MC2P VOL2 (CHASSIS) (CHASSIS) VIDEO(A)-L VIDEO(A)-GND VIDEO(A)-R MIC DETECT MIC AMP DIGITAL ECHO MIC SCORE HP-R HP-GND HP-L VIDEO L R AUDIO VIDEO INPUT PHONES MIC 2 LEVEL MIC 1 LEVEL ECHO LEVEL VOL3 VOL1 MIC 2 MIC 1 (Page 39 (Page 46) (Page 53 Ver. 1.1

• See page 29 for Circuit Boards Location. : Uses unleaded solder. D1502 F-5 D1503 B-5 D1504 B-5 D1505 B-6 D1506 B-6 D1507 B-6 D1508 B-6 IC1501 C-2 IC1502 B-4 IC1503 B-3 IC1504 D-5 IC1505 F-3 IC1506 F-4 Q1500 A-2 Q1501 A-2 Q1502 B-2 Q1503 C-6 Q1504 B-6 Q1505 B-6 Q1506 E-2 Q1507 F-5 Q1508 E-4 Q1509 A-6 Q1510 A-6 Q1511 B-6 Q1512 B-7 Q1513 C-6 Q1514 D-6 • Semiconductor Location Ref. No. Location (Page 45) Ver. 1.1

• See page 67 for IC Block Diagrams. Q1509 R1504 R1525 R1502 R1501 R1500 R1569 R1567 C1545 R1571 R1572 R1568 C1548 R1566 C1554 R1570 R1574 R1575 C1555 R1589 C1559 R1579 R1582 C1562 R1581 C1515 C1517 R1512 C1513 R1514 R1515 C1524 C1525 C1522 C1572 C1568 R1547 D1502 Q1507 C1571 C1552 C1578 R1557 R1549 R1558 R1550 C1570 C1529 R1559 R1507 Q1514 Q1513 R1517 R1516 R1596 R1597 R1598 R1599 Q1512 Q1511 Q1510 CN1502 R1560 R1603 R1601 R1602 R1600 R1527 R1506 JW1513 R1576 C1560 R1573 R1594 C1546 C1561 Q1508 R1580 R1595 R1591 C1544 C1584 IC1506 C1535 C1514 C1537 R1588 R1554 C1533 C1531 C1543 R1552 C1534 R1553 IC1504 C1536 R1555 R1556 C1547 C1540 C1541 C1574 R1565 Q1506 R1590 C1542 C1519 R1546 C1520 R1511 C1518 L1500 10µH IC1501 C1521 C1527 R1510 JW1507 C1512 R1519 R1522 R1538 R1592 C1530 C1526 Q1502 Q1501 Q1500 Q1503 Q1504 Q1505 C2330 C2331 R1593 R1564 R1563 R1561 D1506 D1507 D1508 R1577 R1578 R1583 D1505 D1504 D1503 C1511 R1540 R1539 R1541 R1532 R1531 R1530 R1533 IC1503 IC1502 R1542 R1543 R1534 R1536 R1535 R1544 R1545 IC1505(1/2) IC1505(2/2) C1528 DTC114EKA 100 100 100 100 100 100k 22k 10 50V 100k 1k 22k 47p 2.2k 10 50V 100k 100k 1k 47p 33 10 50V 100k 100k 10 50V 22k 47 10V 0.0015 18k 0.1 18k 18k 0.22 50V 0.22 50V 0.0015 0.1 0.1 10k UDZW-TE17-6.2B 2SC5053 0.1 10 50V 10 50V 100k 10k 100k 10k 10 50V 0.01 100k 100 DTC114EKA DTC114EKA 10k 10k 10k 10k 10k 10k STC114EKA DTC1141EKA DTC114EKA 19P 100k 100k 100k 27k 27k 100 100 4.7k 10 50V 4.7k 0 10 50V 10 50V C1602 10 50V C1601 10 50V 2SK3378 22k 0 47k R1606 22k R1607 22k 0.047 100 10V TC74LVX4052FT 0.033 0.1 0.1 18k 18k 330p 47 10V 0.068 18k 1500p 18k M65850FP 330p 18k 18k 0.068 0.22 50V 0.22 50V 1500p 2.2k 2SK3378 47k R1604 22k 0.0047 0.033 18k 330p 18k 0.068 M65850FP 330p 0.068 18k 0.1 39k 0 27k 0 0.033 C1600 0.1 0.1 2SK3378 2SK3378 2SK3378 2SK3378 2SK3378 2SK3378 0.1 0.033 0 27k 0 39k MA111-TX MA111-TX MA111-TX 10k 10k 10k MA111-TX MA111-TX MA111-TX 0.1 1.2k 1k 1.5k 560 510 470 680 TC74LVX4051FT TC74LVX4051FT 1.8k 2.2k 750 910 820 18k 33k NJM4565M NJM4565M 100 10V CTRL2 CTRL1 CTRL3 S3 S0 S1 S2 CTRL1 R1605 22k CTRL1 CTRL1 CTRL2 CTRL3 S0 S1 S2 S3 CTRL1 CTRL2 CTRL3 OP2OUT VCC CLOCK REF OP2IN LPF2IN LPF2OUT GND CC2 CC1 OP1IN OP1OUT LPF1OUT LPF1IN NC NC OP2OUT VCC CLOCK REF OP2IN LPF2IN LPF2OUT GND CC2 CC1 OP1IN OP1OUT LPF1OUT LPF1IN NC NC INPUT R INPUT L S0 S1 S2 OUTPUT R OUTPUT L AGND AGND AGND AGND SELECTOR AGND DGND S3 A+9V CTRL1 CTRL2 CTRL3 D4 D6 COM D7 D5 INH VEE GND VCC D2 D1 D0 D3 A B C GND VEE INH D5 D7 COM D6 D4 VCC D2 D1 D3 D0 B A C VCC 2X 1X 0X 3X A B 0Y 2Y 3Y 1Y INH VEE GND Y COM X COM LEVEL SHIFT LEVEL SHIFT LEVEL SHIFT LEVEL SHIFT LEVEL SHIFT LEVEL SHIFT MIXER SWITCHING S SIGNAL SELECTOR DIGITAL ECHO SWITCHING S DIGITAL ECHO SWITCHING SWITCHING SWITCHING S S S SWITCHING SWITCHING SWITCHING S S S MULTIPLEXER MULTIPLEXER +5.6V REGULATOR (Page 48) Ver. 1.1

• See page 29 for Circuit Boards Location. : Uses unleaded solder. 7-22. SCHEMATIC DIAGRAM – KARAOKE Board – • Semiconductor Location – KARAOKE Board – Ref. No. Location D2000 C-3 D2001 C-3 D2002 D-3 D2003 D-3 D2006 C-4 D2007 C-4 D2008 C-4 IC2000 C-3 IC2001 B-4 IC2002 B-3 R2001 R2017 C2008 R2035 R2036 R2030 C2016 R2005 C2000 C2005 R2008 C2007 R2012 R2011 C2010 R2007 C2011 R2019 R2020 R2024 R2026 C2013 C2009 R2025 R2016 R2009 C2006 R2015 R2000 R2010 R2021 R2037 C2004 C2002 C2001 NO2000 R2022 IC2000(1/2) IC2001(1/2) IC2000(2/2) IC2002(2/2) R2034 R2031 R2029 IC2002(1/2) C2015 R2002 R2032 R2028 R2004 R2014 D2002 D2001 D2000 D2003 D2008 D2007 IC2001(2/2) D2006 4.7k 4.7k 470p 2.2k 0 0 0.01 47k 100 10V 47 16V 47k 0.1 100k 0 2.2 50V 4.7k 47 16V 4.7k 0 4.7k 0 0.1 47 16V 4.7k 47k 1k 1 50V 2.2k 4.7k 100k 0 0 2.2 50V 47 16V 47 16V 6P 10k NJM3414A NJM2903M-TE2 NJM3414A NJM2903M-TE2 2.2k 22k 22k NJM2903M-TE2 0.1 22k 1.2k 1.5k 2.2k 8.2k MA111-TX MA111-TX MA111-TX MA111-TX MA111-TX MA111-TX NJM2903M-TE2 MA111-TX A+9V MUSIC L+R SCORE XVOICE MIC SCORE AGND COMPARATOR COMPARATOR AC/DC CONVERTER Q522 L-10 Q523 B-6 Q524 C-6 Q550 K-13 Q564 L-11 Q578 K-15 Q579 L-15 Q581 K-14 Q582 K-14 Q585 K-15 Q587 F-6 Q588 E-5 Q589 F-5 D101 L-16 D102 L-16 D136 G-16 D325 K-16 D340 F-4 D341 F-4 D342 F-3 D401 E-5 D402 E-5 D403 E-6 D411 D-4 D412 D-4 D501 C-6 D502 C-6 D503 C-6 D504 C-6 D505 C-6 D506 L-7 Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location • Semiconductor Location – MAIN Board – D507 L-7 D510 H-4 D511 G-4 D550 K-14 D551 K-14 D560 J-10 D561 I-10 D581 K-14 D582 K-15 D583 K-15 D584 E-6 D585 G-16 D586 G-16 IC101 D-9 IC201 D-14 IC301 I-5 IC304 G-6 IC401 C-3 IC501 C-6 IC507 J-14 IC550 L-14 IC558 H-10 IC559 H-9 IC560 H-14 IC561 I-14 Q101 C-8 Q103 G-15 Q104 G-16 Q106 D-11 Q117 C-13 Q151 D-8 Q156 D-10 Q167 C-12 Q200 B-14 Q202 B-15 Q203 B-15 Q204 C-15 Q205 E-14 Q206 J-15 Q207 I-15 Q208 I-16 Q250 C-14 Q252 C-15 Q253 B-15 Q254 B-16 Q255 E-13 Q256 J-15 Q321 K-5 Q322 K-4 Q323 L-16 Q325 K-4 Q340 F-4 Q504 F-3 Q505 L-10 Q506 L-10 Q507 L-9 Q508 L-9 Q509 L-9 Q510 L-9 Q511 L-8 Q512 L-8 Q513 H-11 Q514 L-11 Q515 L-8 Q516 L-10 Q517 L-10 Q518 J-14 Q519 L-8 Q520 H-10 Q521 L-10 Q341 F-4 Q342 F-3 Q343 F-4 Q344 F-4 Q345 F-3 Q370 L-4 Q372 K-4 Q373 K-4 Q375 K-5 Q377 K-5 Q378 L-5 Q379 K-5 Q380 L-5 Q381 J-5 Q382 K-5 Q383 K-5 Q501 B-6 Q503 J-14 (Page 45) (Page 47) Ver. 1.1

ZX100D: E2, E3, E51, SP, MY M501 (FAN) M D-LIGHT SYNC OUT R L AUDIO OUT R L TV/SAT AUDIO IN SYSTEM CONTROL + – SUBWOOFER OUT SUBWOFFER OUT AB SURROUND BOARD NO801 L SURROUND BOARD CN701 (ZX100D) (ZX100D) (ZX80D) TO SS-WGV100D (ZX100D) (ZX100D) 1 42 21 22 TUNER (FM/AM) SUPPLIED WITH THE ASSEMBLED BLOCK FM 75Ω COAXIAL ANTENNA AM D DMB15 BOARD CN302 H MIC BOARD NO1101 K KARAOKE BOARD NO2000 J PRIMARY BOARD CN1200 E VIDEO BOARD CN800 F DRIVER BOARD CN701 A DMB15 BOARD CN106 M EFFECTOR BOARD CN1502 1 9 1 5 (NC) (NC) 1 3 G PANEL BOARD CN902 N SURROUND BOARD CN700 (EXCEPT ZX100D: SP, MY) M502 (FAN) M TAPE MECHANISM DECK BLOCK SUPPLIED WITH THE ASSEMBLED BLOCK (ZX100D) (ZX80D) ZX80D: E2, E3, E13, E51/ ZX100D: E2, E3, E51, SP, MY ZX80D: MX/ ZX100D: MX (FOR ADJUSTMENT) 1 3 4 6 BIAS OSC HRPE1 (REC/PB/ERASE) (DECK-B) HP1 (PB) (DECK-A) 3 1 (CHASSIS) 1 5 E B C 1 2 3 4 5 A B C D E F G H I J 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 K L 1 4 (ZX80D) (ZX80D) (ZX100D) 7-23. PRINTED WIRING BOARD – MAIN Board – • See page 29 for Circuit Boards Location. • See page 44 for Semiconductor Location. : Uses unleaded solder. (Page 58) (Page 55) (Page 64) (Page 52) (Page 52) (Page 30) (Page 30) (Page 36) (Page 44) (Page 65) (Page 40) (Page 38) (Page 30) (Page 42) (Page 55) (Page 55) Note: Refer to SUPPLEMENT-1 for the MAIN board of US mode Ver. 1.1

• See page 54 for Waveforms. • See page 71 for IC Pin Function Description. Q523 R451 R453 R454 R457 R458 R463 R469 R470 R472 R473 R474 R475 R483 R488 R489 R490 R491 R494 R496 R499 R322 R400 R401 R402 R405 R406 R407 R408 R409 R411 R414 R415 R417 R418 R419 R420 R421 R422 R423 R424 R425 R426 R427 R428 R429 R431 R432 R433 R434 R435 R436 R437 R438 R439 R440 R441 R442 R443 R444 R445 R447 R448 R430 R413 R410 X402 C415 C416 X401 C411 C410 C412 R412 R403 R404 CN508 C462 C464 R479 R478 R487 R486 R485 R484 R593 D411 D412 C413 CN402 NO402 CN511 D503 R503 C503 C502 D502 R502 R501 D501 D504 Q524 D505 CN520 C518 R493 R466 R471 CN100 NO401 R574 D401 R573 R468 D402 D403 C414 IC501 R467 R589 Q589 Q587 C583 C584 Q588 R594 R595 R590 CN582 M502 R492 R592 Q501 IC401 R450 JR222 C501 JW100 D584 DTA114EKA 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 47k 10k 100 100 100 100 100 100 100 330k 100 100 10k 100 100 1k 100 100 100 100 100 100 10k 10k 100 100 100 100 100 100 10k 10k 100 100 100 100 100 100 100 100 100 100 100 0 10k 5MHz 0.1 2200 6.3V 32.768KHz 22p 22p 0.1 100k 10k 10k 17P 100 10V 0.01 10k 1k 10k 100 100 10k 1SS355W 1SS355W 0.1 10P 4P 13P 1SS355W 0 0.1 0.1 1SS355W 1k 220 1SS355W 1SS355W DTC124EKA 1SS355W 13P 1000 10V 10k 10k 9P 3P 10k 1SS355W 10k 100 1SS355W 1SS355W 0.1 ICBD4929G 100 1k 2SC2712 2SC2712 0.1 0.1 2SD2525 4.7k 4.7k 100k 3P 4.7k DTC124EKA M30622MEP -A78FPU0 100 0 10 50V UDZS-1713B A1 A2 A3 A4 A5 A6 A7 A8 A9 B1 B2 C1 D3 D1 D2 D4 C2 D5 D6 D7 C3 D8 D9 E1 E2 E3 E4 4 31 32 33 73 74 74 79 80 81 82 53 54 55 73 47 56 34 38 39 89 90 91 66 1 2 3 5 6 35 36 37 48 49 50 52 58 60 61 65 67 72 71 75 78 77 76 83 42 70 63 57 45 44 43 19 18 46 51 32 33 34 31 34 35 36 37 38 39 25 24 23 22 21 32 31 22 21 33 32 31 23 24 25 100 95 94 30 29 9 12 26 27 28 26 27 28 29 30 9 12 12 33 40 41 40 4 41 ∗ ∗ ∗ GC RESET LED+9V BPM LOW VG SPEANA GND MIC DETECT MIC SCORE SPEANA SIRCS KEY INT DISPLAY POWER LED VF(1) IIC-DATA IIC-CLK KEY INT POWER VF(2) GC DGND EVER +4V GC DGND TBL ADDRESS SW MGND D+3.3V M+9V TM-R TM-F E-1 E-2 E-3 OPEN SW D-GND TXD1 RTS1 MCU VCC CLK1 RXD1 CN VSS RESET GND NC D+3.3V D-GND IIC-CLK IIC-DATA RESET X-OUT VSS X-IN VCC NMI IIC-CLK IIC-DATA MODEL-IN AVSS VREF AVCC XC-IN XC-OUT SIRCS DISPLAY-KEY POWER-KEY DEST-IN AC-CUT BYTE VCC VSS DATA CLK OCSW1 SYSRST 3.3VMNT XIFCS IFBSY SIO SOO SCO DGND MIC VOICE KRMOD TUNED ST-CLK ST-CE TBL SENS TM-F TM-R LM-F LM-R A-HALF A-TRIG B-TRIG REC BIAS REC MUTE PB A/B ALC OVER VOLTAGE UNDER VOLTAGE DATA CAPM M-REQ MGND SW-LEVEL-IN THERMAL VACS AUDIO-OUT-SW VIDEO-OUT-SW MTK-POWER EFFECTOR-CTR3 EFFECTOR-CTR2 EFFECTOR-CTR1 EFFECTOR-S3 EFFECTOR-S2 EFFECTOR-S1 EFFECTOR-S0 FAN CONTROL FAN HI SPEED FAN+ FAN- MIC STATUS EJECT SW E3 E2 E1 NO USE SW-MUTE ANALOG-IN-MUTE MTK-KMOD EVER+4V D-GND STBY RLY (1/6) SIO CNVSS SW- LED SW-SPK RELAY CLK Q587,589 FAN MOTOR CONTROL SWITCH FAN MOTOR SWITCH (FAN) ∗R593 150(ZX80D:E13) (EXCEPT ZX100D:SP,MY) ∗R592 680(ZX80D) 1k(ZX100D) ZX80D:E2,E51,MX/ ZX100D:E2,E51,MX 1k 4.7k ∗R493 0(ZX100D:SP,MY) 330(ZX80D:E3/ZX100D:E3) 4.7k ZX80D:E2,E13,E51,MX/ ZX100D:E2,E51,MX Q523,524 B+ SWITCH RESET SIGNAL GENERATOR RESET SWITCH MASTER CONTROLLER H/P DETECT A+9V MIC ECHO MIC AGND VIDEO(A)-R VIDEO(A)-GND VIDEO(A)-L (ZX80D:E3/ZX100D:E3) LM-F LM-R (NC) (NC) MTK- MTK- MTK- SOD CLK GC-RESET STBY-LED TC-RELAY NO USE STK-MUTE REAR-RELAY CTR-RELAY PROTECT TC-MUTE HP-MUTE LINE-MUTE DVD-A-MUTE AUDIO-IC- AUDIO-IC- VOL-IC- VOL-IC- HP-DETECT MIC-DETECT VMUTE A-SHUT B-SHUT B-HALF NO USE ST-DOUT ST-DIN STBY-RELAY EFFECTOR-SELECT MTK-IFBSY MTK-XIFCS FR-RELAY MTK-RESET (Page 32) (Page 37) (Page 59) (Page 50) (Page 49) (Page 51) (Page 48) (Page 41) (Page 47) (Page 50) (Page 66) Note: Refer to SUPPLEMENT-1 for the MAIN board of US model. Ver. 1.1

R105 C121 C122 NO503 IC101 R121 R104 C103 C102 C150 C101 C105 R107 R150 C104 R116 C106 C111 C157 C109 C108 R152 R151 C130 R131 R106 R156 CN505 Q151 R122 R130 C131 R132 C115 R111 Q156 Q106 R108 R158 R159 R160 CN510 R360 R384 C358 R361 R383 R133 R110 R161 R109 C161 C158 C159 C156 R157 R166 C155 R154 C154 C153 C152 C160 C357 Q101 R101 C107 R102 C431 C110 R155 C162 C163 R153 C116 C112 C113 R103 47k 220p 220p 5P M61529FP-60G 1k 1k 10 50V 10 50V 10 50V 100 10V 10 50V 100 2.2k 10 50V 100 0.022 10 50V 0.022 1 50V 0.033 10k 2.2k 10 50V 2.2k 10k 10k 6P 2SC2712 1k 2.2k 0.47 50V 1M 0.1 10k 2SD2114 2SD2114 6.8k 6.8k 3.3k 10k 3P 27k 4.7k 4.7 50V 27k 4.7k 100k 10k 10k 3.3k 10 50V 0.033 1 50V 0.022 100 100 10 50V 1k 10 50V 10 50V 10 50V 0.01 4.7 50V 2SC2712 2.2k 0.022 10k 10 50V 0.01 47k 0.12 0.33 1k 330 10V 0.12 0.33 1k A1 A2 A3 A4 A5 A6 A7 A8 A9 F2 F3 F4 F5 F6 F7 F8 F9 G4 G3 G1 G2 G5 F10 G6 F11 H2 H1 H3 N1 FL FR SAT-R DOWNMIX-R 79 R-OUT 80 L-OUT LINK-L REC-OUT-L SAT-L DOWNMIX-L LINK-R REC-OUT-R XVOICE SCORE +9V V MUTE VIDEO OUT SW +5V A+9V MUSIC L+R SCORE XVOICE NC MIC SCORE L GND R SUR1 SUR2 RECB2 TMI2 TMO2 TCA2 TCB2 TCC2 TOUT2 VOLIN2 BB_A2 BB_B2 OUT2 SWOUT GND CLOCK REF MIC RECB1 TMI1 TMO1 TCA1 TCB1 TCC1 TOUT1 VOLIN1 BB_A1 BB_B1 OUT1 SAOUT VCC DATA TC-L TC-R SAT-R SAT-L DVD-L DVD-R ST-R ST-L VIDEO-L VIDEO-R AGND (2/6) INPUT SELECT SWITCH,TONE CONTROL, FEED BACK SWITCH MUTING MUTING FEED BACK SWITCH ELECTRICAL VOLUME,BASS BOOST AMP ADJUSTMENT FOR (Page 46) (Page 39) (Page 49) (Page 51) (Page 48) (Page 44) (Page 48) (Page 48) (Page 50) (Page 50) Note: Refer to SUPPLEMENT-1 for the MAIN board of US mode Ver. 1.1

C223 C200 C214 R209 R210 C211 R258 C256 C257 R208 C206 C207 R207 C212 C205 C255 R225 R275 C210 R257 R211 C216 C259 R276 C209 R226 C263 R256 R206 C213 R263 R272 R254 R213 R231 R232 R230 Q203 R292 R283 R285 Q254 R284 R233 Q204 R234 R235 C228 R298 R299 C201 C264 R259 C261 R260 R261 C266 R214 C218 R217 R264 C268 R216 R282 R281 Q253 R227 Q202 R229 R280 R202 C277 R228 R203 C226 R265 R267 R266 C269 C219 C270 C220 R215 C215 R212 C265 R262 R277 R278 C276 R242 Q252 R279 R204 C222 R220 R218 R219 C224 C242 R270 Q200 R268 R249 C221 R269 C262 R221 Q250 R222 C251 R273 R271 C225 C273 R224 R223 C272 C260 CN514 D101 D102 R120 D325 R325 Q323 R329 R330 D586 R135 D136 R117 C114 R114 R115 R112 R164 R165 R162 Q117 Q167 R163 R113 C166 C258 R623 R274 C274 R167 C164 C167 D585 C229 C279 R241 R291 R240 R290 CN506 R531 Q103 C267 JW530 CN512 C520 C521 FB260 FB261 C235 J201 R581 JR502 JR509 IC201 R237 R287 Q255 Q205 Q104 C217 JR104 JW258 C227 R582 R532 CN521 C559 R612 R662 J103 C278 C254 C253 R236 R255 C204 C203 R286 R205 R200 0.001 0.1 220p 10k 470 220p 2.2k 0.0022 10 50V 2.2k 0.0022 10 50V 2.2k 0.001 100 10V 100 10V 10k 10k 0.001 2.2k 47k 10 50V 10 50V 22k 10 50V 22k 10 50V 47k 47k 10 50V 6.8k 3.3k 3.3k 6.8k 47k 10k 1k 2SD2114 10k 47k 10k 2SD2114 1k 47k 2SD2114 1k 10k 1 50V 10k 10k 0.1 220p 10k 220p 470 47k 10 50V 47k 0.001 10k 47k 0.001 2.2k 10k 47k 2SD2114 47k 2SD2114 10k 1k 10k 1 50V 1k 10k 1 50V 4.7k 10k 2.2k 10 50V 10 50V 0.001 0.001 4.7k 10 50V 8.2k 10 50V 8.2k 47k 1k 1 50V 10k 2SD2114 10k 10k 10 50V 10k 4.7k 2.2k 10 50V 0.001 47k 2SD2114 1k 10k 1 50V 10k 10 50V 47k 2SD2114 1k 1 50V 10k 10k 1 50V 220p 1k 8.2k 220 10V 0.1 8P 1SS355W 1SS355W 0 UDZSTE -174.7B 680 2SC5053 100k 1k 10EDB40 1.5k UDZSTE -175.6B 0 10 50V 10k 1k 47k 10k 1k 47k 2SD2114 2SD2114 10k 10k 10 50V 10 50V 6.8k 1k 220p 0 10 50V 10 50V 10EDB40 220p 220p 33k 33k 15k 15k 9P 2SC5053 10 50V 19P 10 50V 10 50V 0 0 100p 2P 0 0 M61530 47k 47k 2SC2412K 2SC2412K DTC114EKA 10 50V 0 1 50V 3.3k 3.3k 21P 1000 10V 0 0 5P 1 50V 0.33 0.12 1k 0.33 0.12 1k 10k B1 B2 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 I1 I2 I3 I4 J2 J3 FL FR 70 63 45 44 43 19 18 57 SAT-L SAT-R 1 2 3 5 6 MB_FL LINK-L DM_R DM_L 81 82 LINK-R SW SW SCORE XVOICE MB_FL MB_FR MB_SL MB_SR FC LFE DM_L DM_R LFE FC MB_SR MB_SL MB_FR DOWNMIX-L DOWNMIX-R ∗ ∗ ∗ ∗ ST-CLK ST-CE ST-L A-GND ST-R ST-DOUT/MC-DIN ST-DIN /MC-DOUT ST+9V DGND AGND FC SR SL AGND FR AGND FL AU+5V AGND L-IN AGND R-IN AGND SW(LFE) AGND AGND CTR-IN AGND AGND +9V TUNED LT RT SL-IN SR-IN INPUT R INPUT L S0 S1 S2 OUTPUT R OUTPUT L AGND AGND AGND AGND SELECTOR AGND DGND S3 IIC CLK IIC DATA DGND D+4V CTRL2 CTRL3 CTRL1 SCORE XVOICE L+R(SPEANA) (3/6) MUTING MUTING MUTING AM ANTENNA COAXIAL FM 75Ω SUPPLIED WITH THE ASSEMBLED BLOCK ∗R531,581 6.8k ZX80D:E3,E13,E51,MX/ ZX100D:E3,E51,MX,SP,MY 4.7k (ZX80D:E2:ZX100D:E2) ELECTRICAL VOLUME FEED BACK SWITCH SWITCH FEED BACK MUTING MUTING +5V REGULATOR REGULATOR CONTROL SWITCH +4V REGULATOR MUTING MUTING MUTING MUTING MUTING TUNER (FM/AM) A+9V L R TV/SAT AUDIO IN D-LIGHT SYNC OUT L+R ∗R236,286 10k(ZX100D) 22k(ZX80D) (Page 47) (Page 51) (Page 50) (Page 50) (Page 57) (Page 47) (Page 35) (Page 47) (Page 46) (Page 43) (Page 51) Note: Refer to SUPPLEMENT-1 for the MAIN board of US model. Ver. 1.1

• See page 54 for Waveforms. L320 Q380 T301 IC301 R308 R310 R311 R370 R374 R392 C378 C301 C303 C304 R303 R319 R302 R304 C306 R305 C311 C314 R306 R307 C307 R312 C308 C312 L302 100µH R309 C309 C359 R396 R399 Q377 Q379 Q322 Q321 Q372 Q373 R314 R338 C333 C328 R364 R388 R380 C383 L370 L372 R395 R394 Q378 R376 R375 C373 R373 R372 C372 R371 C379 C377 R377 C374 C371 C370 R378 CN503 R352 R355 R354 R369 R353 C356 C354 C353 C351 R391 C361 C364 C355 R335 C305 C310 C382 C332 Q382 Q383 Q381 R390 C335 C385 C376 R379 CN504 HP1 HRPE1 C326 Q325 Q375 R368 R318 R336 R337 R387 R385 Q370 R386 R339 R301 R389 R351 27mH DTC114EKA HA12237 100 100 100 3.3k 4.7k 6.8k 120p 0.012 0.1 10 50V 10k 2.2k 4.7k 2.2k 2.2 50V 47k 10 50V 0.0022 22k 1M 10 50V 100 470 10V 10 50V 4.7k 47 16V 47 16V 10k 10k 2SA1162 DTC114EKA 2SD2704 2SD2704 2SD2704 2SD2704 2.2k 10k 330p 120p 2.2k 10k 6.8k 330p 27mH 47k 4.7k RT1P137P-TP-1 4.7k 0 0.001 4.7k 0 0.001 4.7k 0.0068 0.01 47 47 10V 0.0047 0.01 100V 10k 8P 4.7k 47k 2.2k 2.2k 10k 2.2 50V 10 50V 0.1 0.012 1k 10 50V 0.0022 1 50V 1k 1 50V 10 50V 1200p 1200p DTA114EKA DTC114EKA DTC114EKA 10k 0.022 0.022 680p 10 3P 680p 2SD2704 2SD2704 2.2k 2.2k 2.2k 2.2k 2.2k 2.2k 2SD596 33 15k 1.5k 15k 1.5k C1 C2 C3 K1 K2 L1 L2 H1 H2 H3 52 53 56 54 55 REC-OUT-R REC-OUT-L REC-OUT-L REC-OUT-R L-PB L-REC R-PB E-HOT R-REC GND GND GND L-PB R-PB GND REC-OUT1 NC ALC1 REC-IN1 NC PB-OUT1 TAI1 EQOUT1 PB -EQ1 PB-NF1B PB-NF1A AIN1 RIP BIN1 REC-RETN GND BIN2 NC AIN2 PB-NF2A PB-EQ2 EOUT2 TAI2 PB-OUT2 NC REC-IN2 ALC2 NC REC-OUT2 PB-NF2B ALC ON/OFF MUTE ON/OFF REC MUTE ON/OFF I-REF TEST ALC DET GND VCC A/B NORMAL SPEED HIGH / (4/6) Q382,383 MUTING CONTROL SWITCH MUTING MUTING MUTING CONTROL SWITCH Q377,379,381 MUTING MUTING MUTING MUTING REC/PB EQ AMP Q378,380 REC BIAS SWITCH BIAS OSC BIAS OSC L-CH R-CH (PB) (DECK-A) R-CH L-CH ERASE (DECK-B) (REC/PB/ERASE) DECK A/B SELECT SWITCH, 1 3 4 6 100µH (Page 47) (Page 50) (Page 46) (Page 51) Note: Refer to SUPPLEMENT-1 for the MAIN board of US mode Ver. 1.1

R575 R513 R317 R320 R381 R300 R365 R350 R316 R315 R382 R366 C511 R518 Q519 Q511 Q512 R533 R534 R519 Q515 R517 Q509 Q510 R516 R515 C510 C517 R552 R553 Q516 R514 Q508 Q507 CN501 R512 C507 C508 R511 Q522 Q521 R529 R530 Q506 Q505 R510 C524 C523 R508 C506 C505 R509 C365 R522 D506 R535 R536 D507 R537 C341 Q344 R341 R345 R349 R346 Q341 D341 R525 R526 R576 R527 R577 R528 Q514 C554 C504 C550 D550 C553 CN502 R358 R356 C352 R321 C363 C362 R359 C325 C551 CN509 D340 Q517 Q343 Q345 D342 C509 C552 C360 Q564 R578 Q340 Q342 R347 R343 R344 R348 R342 C525 R554 R540 R521 R520 JR513 JR515 Q504 CN513 R538 C512 IC550 IC304(2/2) R357 IC304(1/2) R340 C340 10k 15k 22k 33k 4.7k 4.7k 3.3k 4.7k 47k 3.3k 47k 10k 2.2 50V 10k DTA124EKA DTA124EKA DTC114EKA 10k 10k 1k DTC143TKA 47k DTA124EKA DTC114EKA 15k 68k 2.2 50V 2.2 50V 68k 470k DTA124EKA 470k DTC114EKA DTA124EKA 13P 68k 2.2 50V 2.2 50V 470k DTA124EKA DTC114EKA 15k 68k DTC114EKA DTA124EKA 8.2k 2.2 50V 2.2 50V 470k JR516 0 2.2 50V 2.2 50V 68k 1 50V 4.7k 1SS355W 10k 10k 1SS355W 470k 0.0047 DTC114EKA 3.3k 3.3k 3.3k 680 2SB1132 1SS355W D510 1SS355W D511 1SS355W 10k 1k 1k 47k 47k 10k 2SD2114 10 50V 10 50V 100 16V 1SS355W 220 25V 8P 33k 4.7k 47 16V 33k 4.7 50V 4.7 50V 33k 10 50V 0.1 11P 1SS355W DTC114EKA DTC114EKA DTC114EKA 1SS355W 2.2 50V 2.2 50V 33p 2SD2114 10k 2SB1132 2SB1132 2.2k 2.2k 680 680 2.2k 1000 10V 15k 10k 0 10k 0 0 DTC143TKA 13P 5.6k 10 6.3V RT8H015C-TH12-1 NJM4565M(TE2) 4.7k NJM4565M(TE2) 2.2k 0.0047 D1 D2 D3 D4 D5 D6 D7 D8 D9 G1 G2 G3 G4 G5 G6 I1 I2 I3 I4 K1 K2 M1 M2 M3 M4 M7 M8 M10 M11 M12 M5 M9 M6 R-OUT L-OUT 48 50 49 89 47 90 91 46 75 60 76 77 83 65 51 60 61 DOWNMIX-L 94 60 72 DOWNMIX-R 67 66 71 FAN DET POWER-GND POWER-GND UNREG A+9V DGND LINK RELAY AC CUT DETECT FRONT RELAY L-IN R-IN PREGND DC DETECT OVERLOAD DETECT THERMAL VACS STK MUTE -VL -VL TCM MGND B SHUT CAPM+ BTRGM+ ATRGM+ REC(FWD) A SHUT BHALF AHALF TC DGND REC(REV) SW A-GND SW LINE MUTE SW SPK RY STK MUTE UNREG UNREG OVELOAD DC DETECT DVD LINE MUTE CENTER RELAY REAR RELAY (5/6) OVER CURRENT PROTECTOR SPEANA AMP BUFFER MUTING MUTING Q342,345 Q340,343 TRIGGER PLUNGER DRIVE(DECK-A) TRIGGER PLUNGER DRIVE(DECK-B) Q341,344 CAPSTAN/REEL MOTOR DRIVE Q521,522 MUTING CONTROL SWITCH MUTING CONTROL SWITCH Q505,506 MUTING CONTROL SWITCH Q507,508 MUTING CONTROL SWITCH Q512,515,519 Q509,510 MUTING CONTROL SWITCH MUTING CONTROL SWITCH SWITCH Q516,517 MUTING CONTROL ZX80D:E2,E3,E13,E51/ ZX100D:E2,E3,E51,SP,MY ZX80D:MX/ ZX100D:MX (ZX100D) (ZX80D) H/P MUTE FR RELAY PROTECT DBFB F/B CENTER-SPK-SWITCH SW SUPPLIED WITH BLOCK THE ASSEMBLED DECK BLOCK TAPE MECHANISM (2/2) (1/2) AC CUT DETECT (ZX80D) (ZX100D) (Page 51) (Page 49) (Page 46) (Page 57) (Page 53) (Page 48) (Page 47) (Page 46) (Page 53) (Page 48) (Page 51) (Page 47) Note: Refer to SUPPLEMENT-1 for the MAIN board of US model. Ver. 1.1

IC559 IC558 Q520 R243 R244 R294 CN580 C581 C580 D581 Q581 R586 D582 R585 R584 Q585 Q513 R539 R523 R506 R500 R505 C567 C570 C571 C568 C516 C569 Q503 Q518 R524 C515 C513 R507 C557 C558 C564 C563 C565 C562 R295 R245 Q256 Q206 R296 R246 R247 R297 R289 R239 C202 R238 R288 NO523 NO603 C566 C514 EPT560 C530 FB254 R293 FB204 C252 C233 R248 Q208 R602 R250 Q207 R252 C234 R251 R601 R253 JR219 JR218 CN105 R598 R599 L101 L102 R482 R481 R480 IC507 JW550 M501 JW219 C519 D561 R579 Q582 Q579 Q578 D560 R549 Q550 R551 J203 CN102 JR514 J202 TM101 D583 IC561 IC560 D551 TA78033LS TA7805LS 2SB1565F 1k 100k 100k 3P 0.1 0.1 UDZSTE-176.8B 2SC2712 1k UDZSTE-176.2B 1k 10k 2SD2525 DTC114EKA 4.7k 4.7k 4.7k 4.7k 2.7k 6800 25V 0.01 0.01 0.1 2200 10V 0.1 DTC114EKA DTC114EKA 10k 0.1 0.1 10k 0.01 0.01 0.1 470 16V 0.1 470 16V 10k 10k 2SD2114 2SD2114 47k 47k 1k 1k 10k 10k 10 50V 0 0 5P 8P 10000 25V 2200 16V 100p 0 1k 0 10 50V 100p 100k 2SD2704K 10k 33k 2SD2114KT 10k 10 50V 2.2k 1k 10k 0 0 3P 10 10 100 100 1 PQ09RD21 2200 10V D5SBA20 330 2W 2SC2712 2SC2712 DTC114EKA D5SBA20 1.8k DTC143TKA 56k 1P 4P 0 2P HZU2.0BTRF BA09T BA09T 1SS355WTE-17 E1 E2 E3 E4 J2 J3 L1 L2 M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M11 M12 N1 42 58 78 95 100 DGND VF VF AC3 AC3 AC4 AC4 FAN+ FAN- MGND DGND SW+ SW- SW- SW+ GND DGND +9V SW-LED SW VOL (6/6) (CHASSIS) MUTING MUTING MUTING MUTING (ZX80D) (ZX100D) Q503,518 CONTROL SWITCH +9V REGULATOR +9V REGULATOR +9V REGULATOR G I O I O G (FAN) (ZX100D) Q513,520 B+ SWITCH O I G O I G +5V REGULATOR +3.3V REGULATOR 1 2 3 4 FAN MOTOR SWITCH Q581,582 FAN MOTOR SPEED FAN MOTOR CONTROL SWITCH CONTROL SWITCH FAN MOTOR CONTROL SWITCH 1 2 4 3 ZX80D:E2,E3,D13,E51/ ZX100D:E2,E3,E51,SP,MY L R OUT SUBWOOFER OUT SUBWOOFER TO SS-WGV100D SYSTEM CONTROL VP SW+5V SW+3.3V SW+9V AUDIO OUT REGULATOR OVER VOLTAGE DETECT (Page 47) (Page 49) (Page 48) (Page 48) (Page 66) (Page 50) (Page 33) (Page 50) (Page 46) (Page 56) Note: Refer to SUPPLEMENT-1 for the MAIN board of US mode Ver. 1.1

• See page 29 for Circuit Boards Location. : Uses unleaded solder. D609 A-9 D611 F-10 D612 F-10 D620 B-10 D624 F-13 D646 C-14 D654 B-13 D655 B-14 D656 F-5 D658 F-7 D660 G-2 D661 G-2 D670 B-10 IC600 F-11 Q604 B-9 Q606 B-9 Q610 B-9 Q618 B-10 Q628 F-13 Q630 F-13 Q634 B-8 Q640 B-8 Q641 C-7 Q644 I-2 Q647 H-2 Q648 F-2 Q668 B-11 Q682 A-8 • Semiconductor Location Ref. No. Location C603 C653 JR603 R694 D611 R611 R610 R620 C654 C604 D612 R603 R653 R602 R652 C601 C651 R601 R651 R600 R650 R617 R695 R696 R625 R624 R674 C606 R628 R629 R630 R631 Q628 Q630 C605 C683 C693 C682 C681 C691 C692 R676 R656 R657 R658 R660 R661 R677 R678 C660 D620 R621 D646 R609 R698 R608 R693 R606 R692 R607 Q634 R604 R605 Q610 R642 R662 R640 R635 R641 Q682 R643 R663 R639 R638 R697 R634 Q641 Q640 R683 R619 Q604 Q618 D609 R682 Q644 D661 D660 R649 Q648 R685 Q647 R645 R644 R648 R673 R623 R671 Q668 R669 R670 D670 D655 D654 R655 R654 R633 JR602 JR601 JR600 R647 D624 JR612 L680 L690 JW626 R690 R680 JW627 JW600 JW602 JW604 JW605 JW606 JW608 JW614 JW617 JW618 JW619 JW620 JW621 JW622 JW623 JW628 JW629 JW630 JW633 JW634 JW635 JW638 JW639 JW645 JW646 JW649 JW616 JW607 JW613 JW603 JW631 JW688 JW692 JW693 JW694 JW695 JW650 JW647 JW648 JW696 JW687 JW632 JW636 JW624 JW625 R668 RY646 EP690 CN601 TM600 R618 JWH603 JWH602 C602 C600 C650 C652 TH629 C617 C666 R672 R622 C609 D658 D656 C619 C610 C635 C634 C636 C608 C655 R613 R614 R612 R615 R616 R691 R681 R665 JWH601 Q606 C667 C637 C616 JWH600 TH630 R646 NO601 JW601 NO600 JW637 JW640 JW641 JW642 JW643 JW644 JW651 JW652 JW653 JW654 JW655 JW656 JW657 JW658 JW659 JW664 JW665 JW668 JW678 JW679 JW698 JW699 JW700 JW667 JW669 JW682 JW683 JW674 JW675 JW670 JW671 JW672 JW673 JW680 JW684 NO604 C676 C656 C678 C658 CN600 CN607 C618 C648 C649 R636 R637 JW660 JW662 JW663 JW1285 JW1283 JW1282 JW1284 CN602 EP660 IC600 E E E E E E E E E E E E E E 1-864-930- 11 (22, 23) PA BOARD R L FRONT SPEAKER + – + – (CHASSIS) (CHASSIS) Q MAIN BOARD CN502 P MAIN BOARD CN501 U MIC BOARD CN1102 1 4 1 4 (ZX100D) 9 1 1 5 (ZX100D) (ZX100D) (ZX80D) (ZX80D) 2 1 7 1 X SURROUND BOARD NO800 W SURROUND BOARD NO700 V TRANS BOARD CN1212 S TRANS BOARD CN1215 A B C D E F G H I J 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1 3 -1 -2 (ZX100D) (Page 55) (Page 55) (Page 64) (Page 64) (Page 45) (Page 40) (Page 45) Ver. 1.1

TH629 C600 C650 R655 R640 R645 R610 R616 NO604 NO600 C660 R658 R676 R677 R656 R657 C656 R607 Q606 R692 R606 Q604 R605 R604 R693 R608 R698 D609 R694 R609 C608 R611 R612 R603 R619 R617 R695 R696 R653 C606 R630 D620 R669 D670 C601 R601 R600 C651 R651 R650 R682 R683 Q634 R697 R638 R639 R673 R623 R635 R641 R642 R662 R643 R663 Q641 D655 D654 R654 R685 C648 C649 R649 C693 R624 D624 NO601 R634 C634 C635 CN600 CN601 C683 EP660 EP690 C667 R672 R622 R615 TM600 Q630 R631 C655 R628 R629 R691 C691 C692 L690 L680 R681 C681 C682 R690 R680 C605 R647 R660 D660 R661 D661 R646 Q644 Q628 RY646 R648 Q648 R644 D646 R633 JR612 TH630 Q647 IC600 C652 C654 C604 C653 C603 R618 R668 C602 C617 C616 C666 R620 R670 C636 R636 C637 R637 Q668 R671 R621 Q618 Q640 Q682 R613 R614 D656 D658 C676 C658 R678 C678 JW1285 JW1283 JW1282 JW1284 CN602 CN607 Q610 R602 R652 C609 C618 C610 C619 D611 D612 R625 R674 4.7 50V 4.7 50V 47k 1k 10k 68k 1 2P 7P 0.1 100k 220k 220k 220k 220k 3300 100V 2.2k 2SA1207AA 47k 47k 2SC3906K T146E 10k 10k 100k 100k 100k MA111-TX 68k 68k 22 50V 33k 100 47k 1k 100k 100k 100k 47k 0.1 100k MA111-TX 1k MA111-TX 0.0022 47k 1k 0.0022 47k 1k 1k 4.7k DTA124EKA 2.2k 100k 100k 56k 68k 10k 1k 150 150 150 150 2SD2114KT146 TB-E MA111-TX MA111-TX 47k 10k 100 10V 10 50V 22k 0.1 22k MA111-TX 3P 2.2k 100 25V 100 25V 13P 8P 0.1 0.068 10 1/2W 10 1/2W 100 2SC2712-YG-TE85L 100k 10 50V 22k 5.6k 10 1/2W 100000p 100000p 10 1/2W 100000p 100000p 10 1/2W 10 1/2W 0.1 1k 4.7k MA111-TX 4.7k MA111-TX 100 1/2W 2SC2712-YG-TE85L 2SC2712-YG-TE85L 22k 2SC2712-YG-TE85L 2.2k MA111-TX 0 0 2SC2712-YG-TE85L 220 10V 100p 100p 10p 10p 0.22 5W 0.22 5W 220 10V 0.068 0.068 0.068 18k 18k 4.7 100V 820 2W 4.7 100V 820 2W 2SC3906K T146E 150k 150k 2SC3906K T146E 2SD2114KT146 TB-E 2SC2712-YG-TE85L 1k 1W 1k 1W D25XB60 3300 100V 4700 50V 100k 4700 50V 9P 5P 2SC3906K T146E 390 390 10 100V 22 100V 10 100V 22 100V MM3Z18VST1 MM3Z18VST1 22k L-IN L-IN R-IN R-IN DC-DET DC-DET OVERLOAD DET OVERLOAD DET THERMAL VACS THERMAL VACS STK MUTE STK MUTE H/P MUTE H/P MUTE FRONT RELAY AC CUT DETECT AC CUT DETECT AC CUT DETECT FAN DET FAN DET FAN DET FR RELAY PROTECT FR RELAY PROTECT DBFB F/B DBFB F/B FRONT RELAY ∗ +VH +VL -VL -VH SW RC GND AC CUT DETECT -VL +VL GND GND UNREG FAN DET A+9V DBFB F/B FR RELAY PROTECT AC CUT DETECT LINK RELAY STK MUTE L-IN R-IN FRONT RELAY H/P MUTE THERMAL VACS HP-R HP-L -VL -VL SURR POWER GND HP-GND GND REAR L GND REAR R GND CENTER GND AC1 AC1 AC2 AC2 (CHASSIS) (CHASSIS) FRONT SPEAKER Q628,630 THERMAL DETECT -1 -2 RELAY DRIVE PROTECT SWITCH OVER LOAD DETECT STK412-240(ZX80D) STR412-230(ZX100D) PREGND DC DETECT OVERLOAD DETECT DGND POWER AMP OVER LOAD DETECT OVER LOAD DETECT Q604,606,610 STANDBY SWITCH MUTING MUTING Q634,682 MUTING CONTROL SWITCH 1 4 4 1 RBV1306(ZX80D) D25XB60(ZX100D) (ZX100D) (ZX80D) (ZX80D) (ZX100D) FAN DETECT VIRTUAL GND R L POWER-GND POWER-GND 3 2 3 2 (ZX100D) ∗R625 2.2k(ZX80D) 22k(ZX100D) (Page 66) (Page 66) (Page 57) (Page 56) (Page 41) (Page 50) (Page 50) Ver. 1.1

– VIDEO Board – – MAIN Board – – PANEL Board – 1 IC102 6 (DVDRFIP) (DVD play mode) 500 mV/DIV, 200 ns/DIV 1 Vp-p 7 IC102

• See page 29 for Circuit Boards Location. : Uses unleaded solder. Ref. No. Location Ref. No. Location D710 C-11 D711 C-10 D720 G-10 D730 D-9 D761 E-13 D762 H-13 D763 H-13 D764 G-13 D765 D-14 D770 D-9 D780 E-11 D800 E-5 D810 E-2 • Semiconductor Location Ref. No. Location D811 G-4 D812 F-5 D850 F-5 IC702 C-9 IC800 C-5 Q700 F-7 Q720 G-11 Q721 G-11 Q722 F-10 Q730 F-10 Q740 D-7 Q750 E-7 Q762 E-13 Q763 H-13 Q765 H-12 Q770 F-9 Q780 E-10 Q800 E-5 Q810 D-1 Q812 E-3 Q814 F-4 Q815 F-4 Q850 E-5 (Page 52) (Page 45) (Page 45) (Page 45) (Page 52)

D811 R863 R864 R866 R888 R805 R804 R828 C803 C853 R827 C825 R850 C850 R851 C851 R801 R807 R806 C806 R802 C826 C804 R838 R814 R889 R839 C843 R843 C805 Q810 D800 R840 C820 D810 R817 R812 D850 R890 R841 R891 D812 R861 R860 Q814 NO801 R803 B791 IC800 R800 C801 C807 C800 C852 R852 C802 R858 R808 C808 C858 Q812 R842 C839 C838 R892 Q800 Q850 C888 C889 NO800 Q815 RY862 R862 R865 MA111-TX 2.2k 22k 22k 0.22 5W 1 1 100 100p 100p 100 100 50V 1k 4.7 50V 47k 0.01 47k 47k 1k 2.2 50V 100 50V 0.1 0.22 5W 10k 1k 1k 4.7 50V 47k 0.1 2SD2114 MA111-TX 22k 10 50V MA111-TX 10k 2.2k MA111-TX 22k 100k 100k MA111-TX 47k 56k 2SC2712-YG-TE85L 5P 2.2k (CHASSIS) 1k 1 1 4.7 50V 100 10V 270 100 10V 47k 47k 8.2p 8.2p 2SC3906K 10 1/2W 0.068 0.068 10 1/2W 2SC3906K 2SC3906K 0.068 0.068 5P 2SC2712-YG-TE85L ∗ 1k A1 A2 A3 A4 A5 A6 A7 A8 A9 ∗ SW RC GND AC CUT DETECT -VL +VL SW + SW - VIRTUAL GND (1/2) POWER AMP STK403-070(ZX80D) STK403-100(ZX100D) (ZX100D) (ZX100D) ∗R802 MUTING STANDBY SWITCH OVER LOAD DETECT DETECT OVER LOAD RELAY DRIVE PROTECT SWITCH -1 -2 (ZX100D) 270(ZX100D) 1k(ZX80D) (ZX80D) (ZX100D) ZX80D:US,E2,E3,E13,E51/ ZX100D:E2,E3,E51,SP,MY 82 1/2W(ZX80D:MX/ZX100D:MX) 100 1/2W ∗R862 (Page 57) (Page 53) (Page 57) (Page 51) (Page 57) (Page 57) Ver. 1.1

R783 R784 R797 R798 R733 R734 Q700 Q750 R794 R795 R793 C795 C796 C752 C794 C793 CN701 R756 R755 R753 R706 R705 C701 R701 R700 C700 R703 C702 R751 C751 R780 R781 R730 R731 R712 R711 R750 C750 R768 Q765 C792 NO700 TM701 TM700 R777 C773 C772 JW746 JW791 EP700 R776 R779 R778 R788 R787 C782 C783 R737 C732 C733 R786 L730 R736 L770 L780 RY761 JR792 R766 R767 JR791 D762 RY760 JR797 JW790 JW795 R796 R799 JW793 JW796 R725 R724 Q721 R723 R726 C703 C721 R727 C770 C771 R775 R774 R722 Q720 R721 R720 C781 C780 R785 R735 C730 C731 D730 D780 R732 R782 C711 C712 C753 C743 R710 C710 R770 C741 R741 C742 R740 C740 R771 R792 R761 R762 R772 R773 JR700 R704 R754 C754 C704 C791 Q740 R745 R743 R744 JW797 C744 JW798 JW710 CN700 IC702 NO701 R765 R764 Q763 R769 Q780 D711 D710 Q722 R752 R742 R702 Q770 R746 Q730 Q762 D764 D763 D765 D761 D720 D770 100k 47k 22k 1k 100k 56k 2SD2114 2SD2114 100 100 1 22 100V 22 100V 220 10V 100 100V 100 100V 8P 10k 47k 1k 10k 47k 220p 47k 1k 4.7 50V 1k 220 10V 47k 220p 0.22 5W 1k 0.22 5W 1k 47k 47k 1k 4.7 50V 2.2k 2SD2114 0.01 9P 10 1/2W 100000p 100000p 10 1/2W 47k 47k 47k 10 1/2W 100000p 100000p 10 1/2W 100000p 100000p 10 1/2W 10 1/2W 0 2.2k 22k 0 MA111-TX 0 3.3k 1W 3.3k 1W 47k 33k 2SA1207 2.2k 33k 100p 22 50V 33k 0.068 0.068 10 1/2W 68k 22k 2SC2712 10k 10k 0.068 0.068 10 1/2W 10 1/2W 0.068 0.068 MA111-TX MA111-TX 27k 27k 12p 12p 100p 100p 47k 12p 0.22 5W 220p 47k 220 10V 1k 4.7 50V 1k 100k 100k 100k 27k 100k 0 10k 10k 4.7 50V 4.7 50V 0.01 2SD2114 47k 1k 10k 4.7 50V 13P 3P ∗ ∗ 2SC2712 22k 2SC3906K UDZW-TE 17-18B UDZW-TE 17-18B 2SC3906 750 2SC3906K 10k 2SC3906K 2SC2712 MA111-TX MA111-TX MA111-TX MA111-TX MA111-TX MA111-TX A1 A2 A3 A4 A5 A6 A7 A8 A9 SW IN STK MUTE OVELOAD DC DETECT REAR RELAY CENTER RELAY CENTER SL-IN SR-IN SR-IN SL-IN REAR RELAY CENTER RELAY STK MUTE DC DETECT AC CUT DETECT CENTER OVELOAD OVELOAD DC DETECT SW LINE MUTE STK MUTE OVELOAD AC CUT DETECT SW RY SW IN SW LINE MUTE SW RY ∗ ∗ L+R SL-IN SR-IN +VH +VL -VL -VH SURR POWER GND CENTER GND DVD LINE MUTE STK MUTE CENTER RELAY REAR RELAY OVELOAD DC DETECT UNREG REAR R GND REAR L GND FAN DETECT UNREG CENTER SPK SWITCH SW A-GND SW LINE MUTE (2/2) CENTER SPEAKER L R SURR SPEAKER (ZX100D) (CHASSIS) RELAY DRIVE RELAY DRIVE PROTECT SWITCH -1 -2 -1 -2 (ZX100D) (ZX100D) POWER AMP (ZX100D) (ZX100D) Q720-722 STANDBY SWITCH (ZX100D) OVER LOAD DETECT OVER LOAD DETECT OVER LOAD DETECT (ZX100D) MUTING MUTING MUTING (ZX100D) (ZX80D) +9V AGND AGND AGND CTR-IN SW SW SPK RY STK412-240(ZX80D) STK413-430(ZX100D) ∗R702,752 390(ZX100D) 430(ZX80D) ZX80D:US,E2,E3,E13,E51/ ZX100D:E2,E3,E51,SP,MY 82 1/2W(ZX80D:MX/ZX100D:MX) 100 1/2W 82 1/2W(ZX100D:MX) 100 1/2W(ZX100D:E2,E3,E51,SP,MY) ∗R765 ∗R764 (Page 56) (Page 56) (Page 56) (Page 50) (Page 48) (Page 53) (Page 56) Ver. 1.1

• See page 29 for Circuit Boards Location. : Uses unleaded solder. JR904 R1021 C974 C977 C978 C979 C980 C926 C927 JR914 C928 C929 C930 C931 C932 C933 C934 C935 C936 C937 C938 C939 C981 C982 C983 C972 R942 R943 R941 D905 C920 R922 C904 R901 R900 C940 C909 C903 C945 C947 R956 C946 C948 R947 R949 R950 R952 R953 C949 C951 C953 C955 C957 C950 C975 R902 C901 C902 C1180 R905 R903 R904 R906 R907 C910 D932 C954 R948 C952 C958 C956 R951 C959 R954 R1022 R1023 R1024 R1025 R1026 R909 R1027 R1028 R1189 R1187 C906 C925 C905 R912 C916 C908 D931 R1180 Q903 Q917 R908 R1178 R944 R968 R964 R965 R966 R967 R910 R987 Q908 R914 R990 Q909 R916 R974 Q907 Q910 R957 R997 R1135 R1136 Q918 Q919 R1141 R923 R1007 R1008 R1009 R1010 R1011 R1012 R1013 Q904 R979 R982 R980 R981 Q905 Q906 Q901 Q902 Q914 R919 R920 R918 C961 IC904 D901 IC902 C973 JR925 R984 R983 R1181 C917 C964 JW904 JW903 NO904 D927 D928 D908 D909 D910 D916 D917 D1145 D1153 D913 D914 D929 D930 S927 S925 S924 S923 S922 S921 S908 S909 S910 S911 S912 S913 CN902 C943 C922 C923 C924 C900 C941 C942 CN900 C967 IC903 FL901 JW1105 JW900 JW906 JW907 JW908 JW909 JW911 JW912 JW913 JW914 JW915 JW916 JW917 JW918 JW919 JW920 JW921 JW922 JW923 JW924 JW925 JW926 JW927 JW928 JW929 JW931 JW932 JW933 JW934 JW935 JW936 JW937 JW941 JW942 JW943 JW944 JW945 JW946 JW947 JW948 JW949 JW950 JW951 JW952 JW953 JW954 JW955 JW956 JW957 JW958 JW959 JW960 JW961 JW962 JW963 JW964 JW965 JW966 JW967 JW968 JW969 JW970 JW971 JW972 JW973 JW974 JW975 JW976 JW977 JW978 JW979 JW980 JW981 JW982 JW983 JW984 JW985 JW986 JW987 JW988 JW989 JW990 JW991 JW992 JW993 JW994 JW995 JW996 JW997 JW998 JW1000 JW1001 JW1002 JW1003 JW1005 JW1006 JW1007 JW1008 JW1009 JW1010 JW1011 JW1012 JW1013 JW1014 JW1015 JW1016 JW1017 JW1019 JW1020 JW1021 JW1022 JW1023 JW1026 JW1027 JW1029 JW1030 JW1031 JW1032 JW1033 JW1034 JW1035 JW1036 JW1037 JW1038 JW1039 JW1042 JW1043 JW1044 JW1046 JW1047 JW1049 JW1050 JW901 JW902 JW1051 JW1052 JW1053 JW1054 JW1055 JW1056 JW1057 JW1058 JW1059 JW1090 JW1004 JW1018 JW1028 JW1024 JW1045 JW1040 JW1041 JW940 JW939 JW938 FB901 E E E E E E E E E E E E E E 11 20 10 1 1 30 31 50 51 80 81 100 1-868-670- 11 (13) PANEL BOARD 1 7 (RED) 1 3 (GRN) 1 D908,S925 DVD D916,S922 TV/SAT D904,S924 TUNER/ BAND D910,S923 TAPE A/B D917,S921 VIDEO 70 65 64 6 7 1 FLUORESCENT INDICATOR TUBE X901 Z FUNCTION BOARD CN901 G MAIN BOARD CN508 S907 – 913, S921 – 925, 927 N N X S907 D1145,S908 D1153,S909 D913,S910 x PRESET + > D929,S912 TUNING + M y D930,S913 TUNING - m D914,S911 PRESET - . y Y CD-SW BOARD NO1151 A B C D E F G H I 1 2 3 4 5 6 7 8 9 10 11 12 13 14 N N D911 N N D915 (AMBER) (GRN) 1 1 Ref. No. Location Ref. No. Location D901 A-13 D908 D-13 D909 E-13 D910 F-13 D911 B-2 D913 E-3 D914 F-3 D915 B-3 D916 G-13 D917 H-13 D927 B-13 D928 B-13 D929 G-3 • Semiconductor Location Ref. No. Location D930 H-3 D931 E-4 D932 E-4 D1145 C-3 D1153 D-3 IC902 C-7 IC903 C-13 IC904 C-3 Q901 C-11 Q902 C-12 Q903 B-13 Q904 G-4 Q905 G-4 Q906 F-3 Q907 H-3 Q908 E-13 Q909 G-12 Q910 C-2 Q914 C-11 Q917 B-13 Q918 E-3 Q919 F-3 (Page 62) (Page 45) (Page 60) Ver. 1.1

• See page 54 for Waveforms. • See page 67 for IC Block Diagrams. • See page 71 for IC Pin Function Description. R941 R942 R964 FL901 C943 R943 C967 CN902 R1136 R1135 R997 C961 C917 D931 R1013 R1012 R1011 R1010 R1009 R1008 R1007 R922 X901 D905 C1180 C909 C901 C902 R903 R904 C910 R905 R906 R907 R1021 R1022 R1023 R1024 R1025 R1026 R1027 R1028 C906 C916 R909 C908 R902 C905 R912 CN900 Q918 D932 R900 C903 C942 C949 C948 C946 R947 R949 R950 R953 R952 IC904 R983 R984 C945 C950 C952 C954 C956 C947 R948 R951 C958 R954 C959 R956 R901 C904 C900 C964 Q901 Q914 R918 R919 R920 C940 R908 D901 Q917 Q903 R982 R980 Q908 R965 R966 S922 S921 S923 R967 R1181 S924 R968 CLP912 Q909 R957 Q919 JW903 JW904 JR914 C974 FB901 C953 C955 C951 C957 IC903 JW1105 IC902 R1178 R1180 Q906 R910 R987 R914 R990 R974 R916 Q910 NO904 S925 C941 R944 C920 C922 C923 C924 C925 Q905 Q907 Q904 R1141 R923 S907 S908 S909 S910 S911 S912 S913 S927 C977 C978 C979 C980 C926 C927 C928 C929 C930 C931 C932 C934 C935 C936 C933 C937 C938 C939 C981 C982 C983 C972 C973 C975 Q902 D915 D928 D927 R979 R981 D909 D908 D916 D910 D917 D1145 D1153 R1187 R1189 D930 D929 D914 D913 D911 1.5k 1.5k 4.7k 10 50V 10k 10 50V 17P 680 680 680 0.1 0.1 MA111-TX 33k 22k 15k 10k 6.8k 4.7k 3.3k 1M 4MHz 0 220p 220p 220p 220p 100 100 0.1 15k 15k 15k 100 100 100 100 100 100 100 100 220p 0.1 4.7k 220p 10k 0.1 100 17P DTC123JKA MA111-TX 10k 0.1 10 50V 1 470p 470p 1k 1k 1k 1k 1k NJM2760 56k 33k 1 0.0047 0.0047 0.022 0.022 1 6.8k 5.6k 0.047 10k 0.047 2.7k 10k 0.1 4.7 50V 47 10V DTC143TKA DTC143TKA 100k 100k 100k 0.1 100 MA111-TX DTC123JKA RT1P237C-TP-1 470 1k DTC123JKA 6.8k 10k 15k 270 22k DTC123JKA 680 DTC123JKA 0 0.01 0 1 1 1 1 RPM7240-H9 MB90M407PF-G -149E1 22 82 DTC123JKA 680 680 680 680 680 680 DTC123JKA 7P 10 50V 47 0.1 470 6.3V 470 6.3V 470 6.3V 0.01 2SB1132 DTC123JKA 2SB1132 680 680 100p 100p 100p 100p 100p 100p 100p 100p 100p 100p 100p 100p 100p 100p 470p 100p 100p 100p 100p 100p 100p 100p 100p 100p DTC143TKA SEL5423E-TP15 SEL5423E-TP15 SEL5223S -TP15 120 1k SELU5823C -TP15 SELU5823C -TP15 SELU5823C -TP15 SELU5823C -TP15 SELU5823C -TP15 SELU5823C -TP15 SELU5823C -TP15 10k 4.7k SELU5823C -TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 1 2 3 4 5 6 7 8 9 12 13 14 15 16 17 18 19 20 21 22 24 25 26 27 28 29 30 10 31 32 33 34 35 36 37 38 39 40 41 43 44 45 46 47 85 86 87 88 89 90 91 96 97 98 99 100 92 64 65 72 77 78 79 76 61 60 59 58 57 56 55 79 77 61 60 52 53 86 87 88 89 90 91 85 92 97 100 1 2 3 4 5 6 7 8 99 98 9 10 12 13 14 15 16 17 18 19 22 20 24 21 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 47 46 45 44 43 80 74 55 96 64 65 56 57 58 59 72 74 76 78 71 67 68 69 70 54 75 73 66 80 52 53 54 66 67 68 69 70 73 75 71 G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 G13 G14 G15 G16 G17 G18 G19 G20 G21 G12 G22 G23 G24 XIN X0UT LED-PLAY RESET VOLUME OPERATIONAL DIAL LED SELECTOR BF1 BF4 BF3 BF2 ALL-BAND KEY 2 KEY 1 KEY 0 AVSS AVCC 12C-CLOCK 12C-DATA MD2 LED-CD/DVD,TUNER MD0 VKK P36 P35 P34 P33 P32 VSS-IO P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31 P1 P2 VSS-IO P3 P4 P5 P6 P7 P8 VDD-FIP P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 GC RESET EVER +4V VG SPEANA BPM LOW GND VCC NC F1 NP F2 P36 P35 P34 P33 P32 P31 P30 P29 P28 P27 P26 P25 P24 P23 P22 P21 P20 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 G1 G18 G17 G16 G15 G14 G13 G12 G11 G10 G9 G8 G7 G6 G5 G4 G3 G2 NX NX NP NX NX G19 G24 G23 G22 G21 G20 NP NP VF (2) POWER LED VF (1) LED +9V JOG-X-ROUND LED-TAPE,TV/SAT LED-VIDEO,(PAUSE,STOP) LED-(AMS+,AMS-),(FF,FR) LED-FLANGER,CHORUS LED-FLANGER,CHORUS LED-(BALANCE,WAVE,FADER,RANDOM),DELAY BUF2OUT IN1 IN2 BPF4IN2 BPF4IN1 BPF3IN2 BUF1OUT BPF2IN1 BPF2IN2 BPF3IN1 BPF1IN1 BPF1IN2 RECOUT KEY INT POWER KEY INT DISPLAY BPF1OUT BPF2OUT BPF3OUT BPF4OUT SIRCS SEL B SEL A OPERATION DIAL LED VOL 1,2 LED VOL 7,8 LED VOL 5,6 LED VOL 3,4 VOLUME GND KEY INT DISPLAY JOG-X-ROUND KEY 2 SEL B SEL A KEY 0 IN KEY 1 IN KEY 0 OUT KEY 1 OUT LED (BEAT JUMP,BEAT MAX) LED-BAL,WAVE,FADER,RAND LED-(BAL,WAVE,FADER,RAND),DELAY (CHASSIS) FLUORESCENT INDICATOR TUBE GRID DRIVE GRID DRIVE LED DRIVE LED DRIVE BAND-PASS FILTER REMOTE CONTROL RECEIVER VCC- CPU VSS- CPU DISPLAY CONTROLLER LED DRIVE LED DRIVE B+ SWITCH B+ SWITCH LED ON/OFF CONTROL SWITCH CONTROL SWITCH LED ON/OFF LED DRIVE LED DRIVE LED DRIVE IIC-CLK IIC-DATA GC GND GC GND SPEANA GND TUNING + PRESET PRESET - TUNING + - PRESET + PRESET - TUNING + TUNING - DVD TUNER/ BAND TAPE A/B TV/SAT VIDEO LED (BALANCE,WAVE,FADER,RANDOM) GC GND VIDEO DVD TV/SAT TAPE A/B BAND TUNER/ GRID DRIVE (AMBER) (GRN) MD1 LED-VOLUME 1,2 LED-VOLUME 3,4 LED-VOLUME 5,6 LED-VOLUME 7,8 LED-(BEAT JUMP,BEAT MAX) (RED) (GRN) (Page 63) (Page 46) (Page 61) Ver. 1.1

• See page 29 for Circuit Boards Location. : Uses unleaded solder. JR921 JR923 R1003 R1004 R1005 R1006 R963 R1001 R1002 R962 R961 R960 R959 R958 R1014 R973 C907 R972 R1018 R1019 Q921 R1016 R1015 Q920 R1186 CNS902 JW1150 S916 S914 S904 S903 S902 S905 S906 S901 S918 S928 S919 S917 S920 S915 CN901 D1017 D1016 D1020 JW1060 JW1061 JW1062 JW1064 JW1065 JW1066 JW1067 JW1068 JW1069 JW1070 JW1072 JW1073 JW1075 JW1063 JW1078 JW1074 JW1071 S970 R1162 Q911 R1144 R1145 R1146 R1149 R1150 R1151 Q912 R1161 C1150 R1040 JR1096 D920 D919 CNS903 D922 JR1 JR922 R1165 R1164 Q915 Q913 JR4 R1163 R1153 R1154 R1155 JR5 JR3 R1157 R1158 R1159 D924 D926 D923 S1161 JW1088 D925 D921 JR2 FUNCTION BOARD 1-868-671- 11 (13) CD SYNC ENTER MASTER VOLUME ROTARY ENCODER Z PANEL BOARD CN900 1 8 PROGRESSIVE REC/ PAUSE/START GROOVE EQ BAND DIRECTION 1 3 2 DELAY D1016, S915 E AMP MENU CHORUS D1017, S916 FLANGER D1020, S917 E ILLUMINATION DISPLAY SOUND FIELD JOG BOARD 1-868-675- 11 (13) 1 1 8 3 2 E E E E OPERATION DIAL ROTARY ENCODER VOLUME LEVEL 8 VOLUME LEVEL 1 VOLUME LEVEL 2 VOLUME LEVEL 3 VOLUME LEVEL 4 VOLUME LEVEL 5 VOLUME LEVEL 7 VOLUME LEVEL 6 S901 – 906, S914 – 920, 928 A B C D E F G 1 2 3 4 5 6 7 8 9 10 11 • Semiconductor Location Ref. No. Location D919 D-3 D920 C-3 D921 B-3 D922 B-2 D923 B-1 D924 C-1 D925 D-1 D926 D-2 D1016 F-10 D1017 E-10 D1020 D-10 Q911 D-3 Q912 B-3 Q913 C-1 Q915 C-1 Q920 F-9 Q921 D-10 (Page 58)

CN901 R1014 R958 R959 R960 R961 R962 R963 R1006 R1005 R1004 R1003 R1002 R1186 R1001 R972 R973 C907 CNS902 JR1096 R1040 R1161 C1150 CNS903 CLP1151 R1144 R1145 R1146 R1162 R1149 R1150 R1151 R1163 R1164 R1159 R1158 R1157 R1155 R1154 R1153 Q915 Q913 Q912 Q911 D1020 D1017 D1016 Q920 Q921 S970 R1165 S1161 S918 S920 S928 S919 S917 S916 S915 S914 S901 S902 S903 S904 S906 S905 R1018 R1019 R1015 R1016 CLP1152 D919 D920 D921 D922 D923 D925 D926 D924 17P 470 680 1k 1.5k 1.5k 2.2k 3.3k 2.2k 1.5k 1.5k 1k 680 270 470 1k 6.8k 0.001 8P 0 1k 1k 0.001 8P 1k 1k 1k 100 1k 1k 1k 100 100 1k 1k 1k 1k 1k 1k DTC123JKA DTC123JKA DTC123JKA DTC123JKA SLR-343DCT32 SLR-343DCT32 SLR-343DCT32 DTC123JKA DTC123JKA 100 1k 1k 1k 1k SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 KEY 0 IN LED VOL 1,2 LED VOL 3,4 LED VOL 5,6 LED VOL 7,8 OPERATION DIAL KEY 0 IN LED VOL 1,2 LED VOL 3.4 LED VOL 5,6 LED VOL 7,8 OPERATION DIAL LED-FLANGER,CHORUS LED-BAL,WAVE,FADER,RAND OPERATION DIAL GC DGND LED VOLUME 7,8 LED VOLUME 1,2 LED VOLUME 3,4 LED VOLUME 5,6 SEL A SEL B LED VOL 1,2 LED VOL 3,4 LED VOL 5,6 LED VOL 7,8 OPERATION DIAL VOLUME SEL A SEL B SEL A SEL B OPERATION DIAL LED VOLUME 7,8 LED VOLUME 5,6 LED VOLUME 3,4 LED VOLUME 1,2 GND KEY INT DISPLAY KEY 0 OUT KEY 1 OUT KEY 1 IN KEY 0 IN LED-(BAL,WAVE,FADER,RAND),DELAY (CHASSIS) (CHASSIS) ROTARY ENCODER LED DRIVE LED DRIVE LED DRIVE LED DRIVE LED DRIVE LED DRIVE ROTARY ENCODER GND 2A 2B VOLUME LEVEL 8 VOLUME VOLUME VOLUME VOLUME VOLUME VOLUME VOLUME LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4 LEVEL 3 LEVEL 2 LEVEL 1 OPERATION DIAL DELAY CHORUS FLANGER ENTER DELAY CHORUS FLANGER SOUND FIELD ILLUMINATION AMP MENU DISPLAY CD SYNC DIRECTION EQ BAND GROOVE PROGRESSIVE PAUSE/START REC GC DGND MASTER VOLUME (Page 59)

• See page 29 for Circuit Boards Location. : Uses unleaded solder. • Semiconductor Location Ref. No. Location D1040 B-4 D1042 B-6 D1044 B-4 D1046 B-8 D1048 B-8 D1050 B-9 D1052 C-4 D1054 C-5 D1056 B-9 D1058 B-7 Q1041 B-10 R1041 R1042 R1043 R1044 R1045 R1046 R1047 Q1041 C1040 R1051 R1050 JR915 R1048 JR1041 R1056 R1057 R1059 R1058 R1065 R1064 R1060 R1061 R1063 R1062 R1054 R1055 R1053 R1052 R1067 R1066 S1049 S1040 S1045 S1046 S1044 S1042 S1043 S1041 D1044 D1040 D1052 D1054 D1042 D1046 D1048 D1050 D1056 D1058 JW1081 S1047 CN1153 JW1077 JW1079 JW1151 JW1082 JW1083 JW1084 JW1085 R1166 R1167 R1168 R1169 R1170 S1170 S1169 S1168 S1167 S1166 CN1152 JW1086 NO1151 JW1129 JW1130 JW1131 JW1087 E 1-868-674- 11 (13) X-ROUND BOARD 1 3 2 SPEAKERS/ X-ROUND OFF BEAT PAD BEAT JUMP D1048, 1050, S1043 BEAT MAX D1046, 1056, S1042 BALANCE D1052, 1054, S1047 FADER D1040, S1046 WAVE D1044, S1045 RANDOM D1042, 1058, S1044 X-ROUND JOG ROTARY ENCODER 1-868-672- 11 (13) CD-SW BOARD 1 7 Y PANEL BOARD NO904 S1041 – 1047, S1166 – 1170 DISC 1 DISC 2 DISC 3 EX-CHANGE/ DISC SKIP Z OPEN/CLOSE A B C D E F 1 2 3 4 5 6 7 8 9 10 11 (Page 58)

R1167 R1168 R1169 R1170 R1166 NO1151 CN1152 CN1153 Q1041 R1050 R1051 C1040 S1040 R1041 R1042 R1043 R1044 R1045 R1046 R1047 R1048 R1052 R1053 R1066 R1067 R1062 R1063 R1059 R1058 R1054 R1055 R1064 R1057 R1056 R1065 R1060 R1061 S1166 S1167 S1168 S1169 S1170 S1041 S1042 S1043 S1044 S1045 S1046 S1047 S1049 D1048 D1046 D1050 D1056 D1044 D1040 D1054 D1052 D1058 D1042 680 1k 1.5k 1.5k 470 7P 7P 7P DTC123JKA 1k 1k 0.001 2.2k 3.3k 4.7k 6.8k 10k 15k 22k 33k 1k 1k 1k 1k 1k 1k 1k 1k 1k 1k 1k 1k 1k 1k 1k 1k SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 SELU5823C-TP15 LED-BAL LED-BEAT JOG JOG LED-BEAT LED-BAL KEY2 JOG-X-ROUND GC GND JOG-X-ROUND GC GND SEL B KEY 2 SEL A SEL A SEL B KEY2 GC GND SEL A SEL B JOG-X-ROUND (CHASSIS) LED DRIVE ROTARY ENCODER LED(BEAT JUMP,BEAT MAX) OPEN/CLOSE EX-CHANGE/ DISC SKIP DISC 3 DISC 2 DISC 1 LED(BEAT JUMP,BEAT MAX) LED(BEAT JUMP,BEAT MAX) X-ROUND JOG BEAT PAD BEAT MAX BEAT JUMP RANDOM WAVE FADER BALANCE SPEAKERS/ X-ROUND OFF D1048,1050 BEAT JUMP D1046,1056 BEAT MAX WAVE D1042,1058 RANDOM D1052,1054 BALANCE FADER LED-(BALANCE,WAVE,FADER,RAND) LED(BALANCE,WAVE,FADER,RANDOM) LED(BALANCE,WAVE,FADER,RANDOM) (Page 59)

• See page 29 for Circuit Boards Location. : Uses unleaded solder. R1262 R1263 R1264 D1264 NO1211 FH1291 F1291 FH1292 JW1202 JW1201 JW1206 JW1207 JW1216 JW1231 CN1215 JW1222 JW1223 JW1234 JW1233 R1233 CN1212 R1292 C1263 Q1264 C1262 FH1241 FH1242 FH1251 F1241 F1251 FH1261 FH1252 FH1262 FH1272 FH1282 CN1213 C1292 D1292 JW1208 JW1209 JW1220 T1200 POWER TRANSFORMER JW1211 FH1271 F1261 F1271 FH1281 F1281 JW1221 1-864-931- 11 (22, 23) TRANS BOARD B C E 2 (ZX100D) (ZX80D) 1 (ZX80D:US, MX/ZX100D:MX) (ZX80D:US) 1 4 ZX80D:E2, E3, E13, E51/ ZX100D:E2, E3, E51, SP, MY 1 3 7 8 19 5 A B C D E F 1 2 3 4 5 6 7 8 9 10 11 12 13 14 R MAIN BOARD NO603 V PA BOARD NO600 S PA BOARD NO604 AC PRIMARY BOARD CN1204 (Page 65) (Page 52) (Page 52) (Page 45) Ver. 1.1

• See page 29 for Circuit Boards Location. : Uses unleaded solder. Q1200 C1204 R1200 R1201 C1202 C1201 D1200 JR1202 JW1204 NO1201 NO1203 JW1214 JW1212 JW1213 JW1215 CN1204 CN1202 C1206 RY1200 S1200 EP1203 CN1200 L1201 C1200 (ZX80D) E PRIMARY BOARD 1-864-932- 11 (22, 23) POWER SWITCHING 1 2 1 2 1 2 (CHASSIS) 1 3 1 4 (AC IN) VOLTAGE SELECTOR 220V 120V 230 – 240V J MAIN BOARD NO401 AC TRANS BOARD NO1211 ZX80D: E2, E3, E13, E51/ ZX100D: E2, E3, E51, SP, MY ZX80D: US, MX/ ZX100D: MX ZX80D: E2, E3, E13, E51/ ZX100D: E2, E3, E51, SP, MY ZX80D: US, MX/ ZX100D: MX A B C D E F G 1 2 3 4 5 6 (Page 45) (Page 64) Ver. 1.1

L1201 18µH R1262 R1263 C1202 C1201 R1200 C1206 CN1200 R1201 C1204 EP1203 NO1201 CN1212 R1264 C1262 C1263 JR1202 RY1200 Q1200 JW1204 CN1204 JW1234 NO1211 F1251 F1261 F1271 F1281 F1241 F1291 T1200 Q1264 D1264 JW1211 JW1222 JW1223 CN1213 CN1215 D1292 C1292 R1292 CN1202 NO1203 S1200 D1200 8.2k R1233 3.3M 1/2W 8.2k 0.1 0.1 3.3k 1000 6.3V 3P 100k 0.1 2P 7P 1k 10 50V 100 50V 0 2SC2712KT-YG ∗ ∗ ∗ ∗ ∗ ∗ 2SB1565E HZU36BTRF 8P 2P 10EDB40-TB3 100 63V 0.68 2P 2P MA111-TX AC3 AC4 AC4 VF VF AC3 VP GND GND D-GND N L N L EVER+4V DGND GND AC1 AC1 AC2 AC2 EVER+4V STBY RLY D-GND (CHASSIS) (AC IN) POWER ON/OFF RELAY DRIVE VOLTAGE 120V 220V 230-240V ZX80D:US,MX/ ZX100D:MX ZX100D:MX ZX80D:US,MX/ 2P 4P ZX80D:E2,E3, E13,E51/ ZX100D:E2,E3, E51,SP,MY ZX80D:E2,E3, E13,E51/ E51,SP,MY ZX100D:E2,E3, ZX80D:E2,E3,E13,E51/ ZX100D:E2,E3,E51,SP,MY 2P(ZX80D:US,MX/ZX100D:MX) 4P ZX80D:E2,E3,E13,E51/ ZX100D:E2,E3,E51,SP,MY POWER TRANSFORMER -36V REGULATOR (ZX80D) (ZX100D) POWER SWITCHING SELECTOR ∗ NOT REPLACEABLE: BUILD IN TRANSFORMER C1200 (ZX80D) (ZX80D:US) 0.0047 250V ∗F1241,1251,1261,1271 8A 125V (ZX80D:US) 8A 250V (EXCEPT ZX80D:US) ∗F1281, 1291 3.15A 125V (ZX80D:US) 3.15A 250V (EXCEPT ZX80D:US) (Page 53) (Page 53) (Page 51) (Page 46) Ver. 1.1

– DMB15 Board – IC105, 107 TK11133CSCL-G 1 2 3 5 4 VCONT GND NP VIN VOUT CONTROL CIRCUIT OVER HEAT & OVER CURRENT PROTECTION BANDGAP REFERENCE SCF DAC DATT SCF DAC DATT 37 LOUT4– 38 LOUT4+ SCF DAC DATT 39 ROUT3– 40 ROUT3+ SCF DAC DATT 41 LOUT3– 42 LOUT3+ SCF DAC DATT 43 ROUT2– 44 ROUT2+ SCF DAC DATT 45 LOUT2– 46 LOUT2+ SCF DAC DATT SCF DAC DATT 47 ROUT1– 48 ROUT1+ DSD PCM AUDIO I/F 8 PDN 5 DZF1 6 CAD0 3 DZF3 4 DZF2 1 LOUT1– 2 LOUT1+ 9 BICK 10 MCLK 11 DVDD 12 DVSS 13 SDTI4 14 SDTI1 15 SDTI2 16 SDTI3 17 LRCK CONTROL REGISTER 18 I2C 25 DSDL1 26 DSDR1 33 ROUT4+ 32 ROUT4– 27 DSDL2 28 DSDR2 29 DSDL3 30 DSDR3 19 CCLK/SCL 21 CSN/CAD1 20 CDTI/SDA 24 DSDR4 22 DCLK 23 DSDL4 31 DIF0 7 ACKSN 36 AVSS 35 AVDD 34 VREFH IC301 AK4358VQ-L

DECIMATION FILTER WITH HIGH-PASS FILTER SERIAL INTERFACE & MODE/FORMAT CONTROL MODE1 20 MODE0 19 FMT1 18 FMT0 17 OSR 16 SCKI 15 VDD 14 DGND 13 DOUT 12 BCK 11 CLOCK & TIMING CONTROL POWER SUPPLY PDWN 7 IC3601 PCM1803DBR – DRIVER Board – IC701, 712 BA6956AN 1 2 3 4 5 6 7 8 9 CONTROL LOGIC TSD VREF OUT2 OUT1 RNF VM VCC FIN GND RIN 2 OSC ADPCM DECODE DELAY DRAM ADPCM ENCODE ADC DAC S/H POST LPF ALC VOLUME CONTROL OSCC 1 VDD 3 OSCR 4 NC 5 VOL1 (CS) 6 VOL2 (SCL) 7 VOL3 (SDA) 8 NC 9 VRO VREF VDA NC ALC1 MC1N MC1P 15 16 14 13 12 11 10 VREF VREF VREF VREF ALC VREF MC2P 17 MC2N 18 ALC1 19 NC 20 VSA 21 MCO 22 PRIN 23 ADIN 24 NC 25 DA OUT 26 VOLST 27 NC 28 TEST 29 POOUT 30 VSS – MIC Board – IC1100 TC9488FG

IC1501, 1504 M65850FP-E1 OSCILLATOR 1/2 VCC AUTO RESET LPF1 MAIN CONTROL A/D 20KBIT SRAM LPF2 D/A 2 3 4 5 6 7 8 9 10 11 15 14 13 12 CLOCK RESET MO MI D1 DO0 DO1 VCC 16 NC CLOCK REF OP2IN OP2OUT LPF2IN LPF2OUT LPF1IN 1 NC LPF1OUT OP1OUT OP1IN CC1 CC2 GND 1 D4 2 D6 3 COM 4 D7 5 D5 6 INH 7 VEE 8 GND 9 C 10 B 11 A 12 D3 13 D0 14 D1 15 D2 16 VCC OUT C IN OUT C IN OUT C IN OUT C IN OUT C IN OUT C IN OUT C IN OUT C IN LOGIC LEVEL CONVERTER 16 13 15 11 9 10 2 3 6 7 8 A B 3X 14 1X 12 0X 2X X-COM VCC GND VEE INH Y-COM 2Y LOGIC LEVEL CONVERTOR C OUT IN C OUT IN C OUT IN C OUT IN C OUT IN C OUT IN C OUT IN C OUT IN 1 0Y 4 5 1Y 3Y IC1502, 1503 TC74LVX4051FT IC1506 TC74LVX4052FT

IC904 NJM2760V-TE2 IN1 1 BPF2OUT 15 BPF1OUT 16 RECOUT 17 BPF2OUT 20 IN2 2 BUF1OUT 3 BPF2IN1 4 BPF2IN2 5 BAND-PASS FILTER BPF3IN1 6 BPF3IN2 7 BAND-PASS FILTER BPF4IN1 8 BPF4IN2 9 GND 10 BAND-PASS FILTER DET DET BPF1IN2 19 BPF1IN1 18 BAND-PASS FILTER DET BPF3OUT 14 DET BPF4OUT 13 N.C. 12 V+ 11 DET

DMB15 BOARD IC102 CXD9849R (RF AMP, SERVO DSP, MPEG DECODER) Pin No. Pin Name I/O Description 1 AGND - Ground terminal 2 DVDA I AC coupled input path A 3 DVDB I AC coupled input path B 4 DVDC I AC coupled input path C 5 DVDD I AC coupled input path D 6 DVDRFIP I AC coupled DVD RF signal input from the optical pick-up block 7 DVDRFIN I AC coupled DVD RF signal input terminal Not used 8 MA I DC coupled main-beam RF signal input A 9 MB I DC coupled main-beam RF signal input B 10 MC I DC coupled main-beam RF signal input C 11 MD I DC coupled main-beam RF signal input D 12 SA I DC coupled sub-beam RF signal input A Not used 13 SB I DC coupled sub-beam RF signal input B Not used 14 SC I DC coupled sub-beam RF signal input C Not used 15 SD I DC coupled sub-beam RF signal input D Not used 16 CDFON I CD focusing error negative input terminal Not used 17 CDFOP I CD focusing error positive input terminal Not used 18 TNI I 3 beam satellite PD signal negative input from the optical pick-up block 19 TPI I 3 beam satellite PD signal positive input from the optical pick-up block 20, 21 MDI1, MDI2 I Laser power monitor input from the optical pick-up block 22 LDO2 O Laser diode drive signal output to the optical pick-up block (for DVD) 23 LDO1 O Laser diode drive signal output to the optical pick-up block (for CD) 24 SVDD3 - Power supply terminal (+3.3V) 25 CSO O Central servo signal output terminal Not used 26 RFLVL O RFRP low pass output terminal Not used 27 SGND - Ground terminal 28 V2REFO O Reference voltage (+2.8V) output terminal Not used 29 V2O O Reference voltage (+2V) output to the optical pick-up block 30 VREFO O Reference voltage (+1.4V) output terminal 31 FEO O Focus error monitor output terminal Not used 32 TEO O Tracking error monitor output terminal Not used 33 TEZISLV O Slice level of tracking error signal output terminal Not used 34 OPOUT O Output from the internal operational amplifier Not used 35, 36 OPIN I Input to the internal operational amplifier Not used 37 DMO O Spindle motor control signal output to the motor driver 38 FMO O Sled motor control signal output to the motor driver 39 TROPENPWM O Loading motor control signal output terminal Not used 40 IOPMON I Power monitor terminal 41 TRO O Tracking coil control signal output to the coil driver 42 FOO O Focus coil control signal output to the coil driver 43 DVSS - Ground terminal 44, 45 NC - Not used 46 DVDD3 - Power supply terminal (+3.3V) 47 SPFG I Spindle motor hall sensor input from the motor driver 48 DSEL O Interlace/progressive selection signal output terminal Not used

"L": normal, "H": squeeze 50 MSW O CD/DVD selection signal output terminal "L": CD, "H": DVD 51 MAMUTE - Muting control signal output terminal Not used 52 DVDD18 - Power supply terminal (+1.8V) 53 to 61 IOA2 to IOA8, IOA18, IOA19 O Address signal output to the flash ROM 62 DVSS - Ground terminal 63 APLLCAP - Connection terminal for an external capacitor 64 APLLVSS - Ground terminal 65 VDD3 - Power supply terminal (+3.3V) 66 IOWR O Write enable signal output to the flash ROM 67 to 72 IOA16 to IOA11 O Address signal output to the flash ROM 73 DVDD3 - Power supply terminal (+3.3V) 74 to 76 IOA10, IOA9, IOA20 O Address signal output to the flash ROM 77 IOCS O Chip select signal output to the flash ROM 78 IOA1 O Address signal output to the flash ROM 79 IOOE O Output enable signal output to the flash ROM 80 DVDD3 - Power supply terminal (+3.3V) 81 to 84 AD0 to AD3 I/O Data/address signal input/output terminal with the flash ROM 85 DVSS - Ground terminal 86 to 88 AD4 to AD6 I/O Data/address signal input/output terminal with the flash ROM 89 IOA21 O Address signal output to the flash ROM 90 ALE O Address latch enable signal output terminal Not used 91 AD7 I/O Data/address signal input/output terminal with the flash ROM 92, 93 IOA17, IOA0 O Address signal output to the flash ROM 94 DVSS - Ground terminal 95 UWR O Write enable signal output terminal Not used 96 URD O Data read enable signal output terminal Not used 97 DVDD18 - Power supply terminal (+1.8V) 98 IFSDO O Serial data output to the master controller 99 IFCK O Serial data transfer clock signal output to the master controller 100 XIFCS O Chip select signal output to the master controller 101 IFSDI I Serial data input from the master controller 102 SCL O Serial data transfer clock signal output to the EEPROM and D/A converter 103 SDA I/O Two-way data bus with the EEPROM and D/A converter 104 TRG-SW I Trigger detection switch input terminal Not used 105 IFBSY I Busy signal input from the master controller 106 RXD I Receive data input terminal for UART communication when data writing to flash memory 107 TXD O Transmit data output terminal for UART communication when data writing to flash memory 108 DVDD3 - Power supply terminal (+3.3V) 109 ICE I ICE mode enable signal input terminal Not used 110 PRST I Reset signal input from the master controller "L": reset 111 IR I IR control signal input terminal Not used 112 INT0 O Interrupt request signal output terminal Not used 113 DQM0 O Data mask signal output to the SD-RAM 114 MREQ O Muting request signal output terminal Not used

116 DVSS - Ground terminal 117, 118 RD6, RD5 I/O Two-way data bus with the SD-RAM 119 DVSS - Ground terminal 120, 121 RD4, RD3 I/O Two-way data bus with the SD-RAM 122 DVDD18 - Power supply terminal (+1.8V) 123 to 126 RD2 to RD0, RD15 I/O Two-way data bus with the SD-RAM 127 DVDD3 - Power supply terminal (+3.3V) 128 to 133 RD14 to RD9 I/O Two-way data bus with the SD-RAM 134 DVSS - Ground terminal 135 RD8 I/O Two-way data bus with the SD-RAM 136 GPIO - Not used 137 DQM1 O Data mask signal output to the SD-RAM 138 RWE O Write enable signal output to the SD-RAM 139 CAS O Column address strobe signal output to the SD-RAM 140 RAS O Row address strobe signal output to the SD-RAM 141 DVDD3 - Power supply terminal (+3.3V) 142 RCS O Chip select signal output to the SD-RAM 143 BA0 O Bank address signal output to the SD-RAM 144 DVSS - Ground terminal 145 BA1 O Bank address signal output to the SD-RAM 146, 147 RA10, RA0 O Address signal output to the SD-RAM 148 DVSS - Ground terminal 149 to 151 RA1 to RA3 O Address signal output to the SD-RAM 152 DVDD18 - Power supply terminal (+1.8V) 153, 154 NC - Not used 155 DVDD3 - Power supply terminal (+3.3V) 156 RCLK O Serial data transfer clock signal output to the SD-RAM 157 CKE O Clock enable signal output to the SD-RAM 158 to 160 RA11, RA9, RA8 O Address signal output to the SD-RAM 161 DVSS - Ground terminal 162 RA7 O Address signal output to the SD-RAM 163 DVSS - Ground terminal 164 to 166 RA6 to RA4 O Address signal output to the SD-RAM 167 DVDD3 - Power supply terminal (+3.3V) 168 DISC/X - Not used 169 RGB - Not used 170 TSD_M O Thermal shut down signal output to the motor/coil driver 171, 172 NC - Not used 173 DVDD18 - Power supply terminal (+1.8V) 174 FWD O Loading motor drive signal output terminal (forward direction) Not used 175 NC - Not used 176 LIMSW I Limit detection switch input terminal 177 OCSW I Disc table open/close detection switch input terminal Not used 178 REV O Loading motor drive signal output terminal (reverse direction) Not used 179 CKSW I Chucking detection switch input terminal Not used 180, 181 NC - Not used

183 to 188 NC - Not used 189 DAVCC - Power supply terminal (+3.3V) 190 VREF - For bandgap reference voltage terminal 191 FS - Full scale adjustment terminal 192 YUV0 O Video data output terminal Not used 193 DAVSS - Ground terminal 194 YUV1 O Y signal output to the video amplifier 195 DAVDD - Power supply terminal (+3.3V) 196 YUV2 O Chroma signal output to the video amplifier 197 DAVSS - Ground terminal 198 YUV3 O Video signal output to the video amplifier 199 DAVDD - Power supply terminal (+3.3V) 200 YUV4 O Chroma signal output to the video amplifier 201 DAVSS - Ground terminal 202, 203 YUV5, YUV6 O Component video signal output to the video amplifier 204 DVDD3 - Power supply terminal (+3.3V) 205 MIC I Microphone detection signal input from the master controller "H": microphone in 206 VOICE I Voice signal input terminal 207 KRMOD O Karaoke mode selection signal output to the master controller "H": karaoke mode 208 SMSCK I Score signal input terminal 209 SPDATA I SPDIF digital audio data input from the A/D converter 210 MUTE O Muting signal output to the motor/coil driver 211 MUTE123 O Muting signal output to the motor/coil driver 212 DVDD3 - Power supply terminal (+3.3V) 213 ALRCK O L/R sampling clock signal output to the D/A converter and A/D converter 214 ABCK O Bit clock signal output to the D/A converter and A/D converter 215 ACLK O Master clock signal output to the D/A converter and A/D converter 216 DVSS - Ground terminal 217 to 219 ASDATA0 to ASDATA2 O Audio serial data output to the D/A converter 220 XRST O Reset signal output to the D/A converter "L": reset 221 DVDD18 - Power supply terminal (+1.8V) 222 ASDATA4 O Audio serial data output to the D/A converter 223 DVSS - Ground terminal 224 DWIDE - Not used 225 SPDIF O SPDIF digital audio signal output terminal Not used 226 RFGND18 - Ground terminal 227 RFVDD18 - Power supply terminal (+1.8V) 228 XTALO O System clock output terminal (27 MHz) 229 XTALI I System clock input terminal (27 MHz) 230 JITFO O Output terminal of the RF jitter meter 231 JITFN I Input terminal of the RF jitter meter 232 PLLVSS - Ground terminal 233 IDAC - Not used 234 PLLVDD3 - Power supply terminal (+3.3V) 235 LPFON O Data PLL loop filter output terminal 236 LPFIP I Data PLL loop filter input terminal

238 LPFOP O Data PLL loop filter output terminal 239 VDD3 - Power supply terminal (+3.3V) 240 NC - Not used 241 VSS - Ground terminal 242, 243 NC - Not used 244 RFVDD3 - Power supply terminal (+3.3V) 245 RFRPDC O RF ripple detect output terminal 246 RFRPAC I RF ripple detect input terminal 247 HRFZC I High frequency RF ripple zero crossing terminal 248 CRTPLP O Defect level filter capacitor connecting terminal 249 RFGND - Ground terminal 250, 251 NC - Not used 252 OSP O RF offset cancellation capacitor connecting terminal 253 OSN O RF offset cancellation capacitor connecting terminal 254 RFGC O RF AGC loop capacitor connecting for DVD-ROM 255 IREF I Reference current input terminal 256 AVDD3 - Power supply terminal (+3.3V)

Pin No. Pin Name I/O Description 1 TUNED I Tuning detection signal input from the tuner (FM/AM) "L": tuned 2 ST-DOUT O PLL serial data output to the tuner (FM/AM) 3 ST-CLK O PLL serial data transfer clock signal output to the tuner (FM/AM) 4 SIRCS I Remote control signal input from the remote control receiver 5 ST-DIN I PLL serial data input from the tuner (FM/AM) 6 ST-CE O PLL serial chip enable signal output to the tuner (FM/AM) 7 STBY-RELAY O Relay drive signal output for the main power "H": power on 8 BYTE I External data bus width selection signal input terminal Fixed at "L" in this set 9 CNVSS I Processor mode switch input terminal (for test) 10 XC-IN I Sub system clock input terminal (32.768 kHz) 11 XC-OUT O Sub system clock output terminal (32.768 kHz) 12 RESET I System reset signal input from the reset signal generator "L": reset For several hundreds msec. after the power supply rises, "L" is input, then it change to "H" 13 X-OUT O Main system clock output terminal (5 MHz) 14 VSS - Ground terminal 15 X-IN I Main system clock input terminal (5 MHz) 16 VCC - Power supply terminal (+3.3V) 17 NMI I Non-maskable interrupt input terminal Fixed at "H" in this set 18 EFFECTOR- SELECT O Effector on/off control signal output to the signal selector "H": effector on 19 EFFECTOR-S0 O Effector circuit delay time selection signal output to the multiplexer 20 AC-CUT I AC cut on/off detection signal input from the reset signal generator "L": AC cut on 21 MIC STATUS O Microphone detection signal output to the servo DSP "H": microphone in 22 MTK-KMOD I Karaoke mode selection signal input from the servo DSP "H": karaoke mode 23 MTK-IFBSY O Busy signal output to the servo DSP 24 MTK-XIFCS I Chip select signal input from the servo DSP 25 MTK-RESET O Reset signal output to the servo DSP "L": reset 26 EJECT SW I Disc table open/close detection signal input terminal "L": open, "H": close 27 TBL SENS I Disc table address sensor input terminal 28 E3 I Disc table address detection signal input terminal 29 IIC-CLK I/O Two-way IIC clock bus with the display controller 30 IIC-DATA I/O Two-way I2C data bus with the display controller 31 MTK-SIO O Serial data output to the servo DSP 32 MTK-SOD I Serial data input from the servo DSP 33 MTK-CLK I Serial data transfer clock signal input from the servo DSP 34, 35 E2, E1 I Disc table address detection signal input terminal 36 TM-F O Table motor drive signal output terminal (forward direction) 37 TM-R O Table motor drive signal output terminal (reverse direction) 38 LM-F O Loading motor drive signal output terminal (forward direction) 39 LM-R O Loading motor drive signal output terminal (reverse direction) 40 GC-RESET O Reset signal output to the display controller "L": reset 41 STBY-LED O LED drive signal output terminal "L": red LED on (standby mode),"H": green LED on (power on mode) 42 FAN CONTROL O Fan motor on/off control signal output terminal "L": motor on 43 to 45 EFFECTOR-S1 to EFFECTOR-S3 O Effector circuit delay time selection signal output to the multiplexer

47 A-HALF I Deck-A cassette detection signal input from the tape mechanism deck block "L": cassette in 48 A-TRIG O Deck-A side trigger plunger drive signal output terminal "H": plunger on 49 B-TRIG O Deck-B side trigger plunger drive signal output terminal "H": plunger on 50 CAPM O Capstan/reel motor drive signal output terminal "L": FWD/stop, "H": REV 51 SW-SPK RELAY O Relay drive signal output for the subwoofer (SS-WGV100D) "H": relay on (HCD-ZX100D only) 52 REC BIAS O Recording bias on/off control signal output terminal "H": bias on 53 TC-RELAY O Recording/playback selection signal output terminal "L": playback, "H": recording 54 REC MUTE O Recording muting on/off control signal output to the REC/PB EQ amplifier "L": muting on 55 PB A/B O DECK-A/B selection signal output to the REC/PB EQ amplifier "L": deck-B, "H": deck-A 56 ALC O Automatic limiter on/off control signal output to the REC/PB EQ amplifier "H": limiter on 57 EFFECTOR-CTR1 O Effector mode control signal output terminal "L": delay1, delay 2, effector off, "H": flanger 1, flanger 2, chorus 1, chorus 2 58 FAN HI SPEED O Fan motor speed control signal output terminal "L": hi speed 59 NO USE - Not used 60 STK-MUTE O System muting on/off control signal output terminal "L": muting on, "H": power amplifier on Muting on/off control signal output for subwoofer out "L": muting on (HCD-ZX80D only) 61 REAR-RELAY O Relay drive signal output for the surround (rear) speaker "H": relay on 62 VCC - Power supply terminal (+3.3V) 63 EFFECTOR-CTR2 O Effector mode control signal output terminal "L": delay 2, effector off, "H": flanger 1, flanger 2, chorus 1, chorus 2, delay1 64 VSS - Ground terminal 65 CTR-RELAY O Relay drive signal output for the center speaker "H": relay on 66 FR-RELAY O Relay drive signal output for the front speaker "H": relay on 67 PROTECT I Speaker protect detection signal input terminal "L": protect on 68 OVER VOLTAGE I Over voltage detection signal input terminal "H": over voltage is detected (Except US and Mexican models only) 69 UNDER VOLTAGE I Under voltage detection signal input terminal "L": under voltage is detected (Except US and Mexican models only) 70 EFFECTOR-CTR3 O Effector mode control signal output terminal "L": chorus 1, chorus 2, effector off, "H": flanger 1, flanger 2, delay1, delay 2 71 TC-MUTE O Playback muting on/off control signal output terminal "H": muting on 72 HP-MUTE O Headphone muting on/off control signal output terminal "H": muting on 73 DISPLAY-KEY I DISPLAY key input terminal (interrupt input) 74 POWER-KEY I POWER key input terminal (interrupt input) 75 SW-MUTE O Muting on/off control signal output for subwoofer out "L": muting on (HCD-ZX80D only) 76 LINE-MUTE O Line muting on/off control signal output terminal "H": muting on 77 DVD-A-MUTE O CD/DVD analog signal muting on/off control signal output terminal "H": muting on 78 MTK-POWER O Power on/off control signal output for the CD/DVD sections "H": power on 79 AUDIO-IC-DATA O Serial data output to the audio control 80 AUDIO-IC-CLK O Serial data transfer clock signal output to the audio control 81 VOL-IC-DATA O Serial data output to the electrical volume 82 VOL-IC-CLK O Serial data transfer clock signal output to the electrical volume 83 AUDIO-OUT-SW O Audio out muting on/off control signal output terminal "H": muting on 84 HP-DETECT I Headphone detection signal input terminal "H": headphone in 85 MIC-DETECT I Microphone detection signal input terminal "H": microphone in Ver. 1.1

"L": DVD video output, "H": video input output 88 VMUTE O Video muting on/off control signal output to the video amplifier "L": muting on 89 A-SHUT I Deck-B tape reel rotating detection signal input from the tape mechanism deck block 90 B-SHUT I Deck-A tape reel rotating detection signal input from the tape mechanism deck block 91 B-HALF I Deck-B cassette detection signal, recording-proof (forward direction) detection signal and recording-proof (reverse direction) detection signal input from the tape mechanism deck block (A/D input) "L": cassette in and recording possible 92 MODEL-IN I Model setting input terminal (A/D input) 93 DEST-IN I Destination setting input terminal (A/D input) 94 THERMAL VACS I Thermal VACS detection signal input from thermal sensor (A/D input) 95 SW-LEVEL-IN I Subwoofer volume level detection signal input from the SS-WGV100D (HCD-ZX100D only) 96 AVSS - Ground terminal (for A/D conversion) 97 NO USE - Not used 98 VREF I Reference voltage (+3.3V) input terminal (for A/D converter) 99 AVCC - Power supply terminal (+3.3V) (for A/D conversion) 100 SW-LED O LED drive signal output to the SS-WGV100D for subwoofer on indicator "H": LED on (HCD-ZX100D only)

Pin No. Pin Name I/O Description 1 to 8 G8 to G1 O Grid drive signal output to the fluorescent indicator tube 9, 10 P1, P2 O Segment drive signal output to the fluorescent indicator tube 11 VSS-IO - Ground terminal (for I/O port) 12 to 22 P3 to P13 O Segment drive signal output to the fluorescent indicator tube 23 VDD-FIP - Power supply terminal (+3.3V) (for fluorescent indicator tube) 24 to 41 P14 to P31 O Segment drive signal output to the fluorescent indicator tube 42 VSS-IO - Ground terminal (for I/O port) 43 to 47 P32 to P36 O Segment drive signal output to the fluorescent indicator tube 48 VKK - Power supply terminal (-36V) (for fluorescent indicator tube) 49, 50 MD0, MD1 I Setting terminal for the CPU operation mode Fixed at "H" in this set 51 MD2 I Setting terminal for the CPU operation mode Fixed at "L" in this set 52 LED-CD/DVD, TUNER O LED drive signal output for the DVD and TUNER/BAND indicator "H": LED on 53 LED-TAPE, TV/SAT O LED drive signal output for the TAPE A/B and TV/SAT indicator "H": LED on 54 LED-VIDEO, (PAUSE, STOP) O LED drive signal output for the VIDEO, pause and stop indicator "H": LED on 55 LED- (AMS+, AMS-), (FF, FR) O LED drive signal output for the AMS+, AMS-, FF and FR indicator "H": LED on 56 LED-VOLUME 1, 2 O LED drive signal output for the volume level 1 and 2 indicator "H": LED on 57 LED-VOLUME 3, 4 O LED drive signal output for the volume level 3 and 4 indicator "H": LED on 58 LED-VOLUME 5, 6 O LED drive signal output for the volume level 5 and 6 indicator "H": LED on 59 LED-VOLUME 7, 8 O LED drive signal output for the volume level 7 and 8 indicator "H": LED on 60 I2C-DATA I/O Two-way I2C data bus with the master controller 61 I2C-CLOCK I/O Two-way I2C clock bus with the master controller 62 AVCC - Power supply terminal (+3.3V) (for A/D converter) 63 AVSS - Ground terminal (for A/D converter) 64 to 66 KEY 0 to KEY 2 I Front and top panel key input terminal (A/D input) 67 ALL-BAND I Spectrum analyzer drive signal input from the band-pass filter 68 BF4 I Spectrum analyzer drive signal input from the band-pass filter (for 80 Hz) 69 BF3 I Spectrum analyzer drive signal input from the band-pass filter (for 300 Hz) 70 BF2 I Spectrum analyzer drive signal input from the band-pass filter (for 1.2 kHz) 71 BF1 I Spectrum analyzer drive signal input from the band-pass filter (for 8 kHz) 72 OPERATION DIAL I Jog dial pulse input from the rotary encoder (OPERATION DIAL) 73 JOG-X-ROUND I Jog dial pulse input from the rotary encoder (X-ROUND JOG) 74 VOLUME I Jog dial pulse input from the rotary encoder (MASTER VOLUME) 75 LED- (BEAT JUMP, BEAT MAX) O LED drive signal output for the BEAT JUMP and BEAT MAX indicator "H": LED on 76 LED- (BALANCE, WAVE, FADER, RANDOM), DELAY O LED drive signal output for the BALANCE, WAVE, FADER, RANDOM and DELAY indicator "H": LED on 77 RESET I Reset signal input from the master controller "L": reset 78 LED-FLANGER, CHORUS O LED drive signal output for the FLANGER and CHORUS indicator "H": LED on 79 LED-PLAY O LED drive signal output for the play indicator "H": LED on 80 LED SELECTOR O LED selection signal output terminal

82 XOUT O System clock output terminal (4 MHz) 83 XIN I System clock input terminal (4 MHz) 84 VCC-CPU - Power supply terminal (+3.3V) (for CPU) 85 to 100 G24 to G9 O Grid drive signal output to the fluorescent indicator tube

back panel section not supplied (X-ROUND board) 2 2 11 10 2 3 4 5 #2 #2 6 7 6 7 8 9 SECTION 8 EXPLODED VIEWS • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. • Accessories are given in the last of the electrical parts list. NOTE: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) ↑ ↑ Parts Color Cabinet's Color The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • Abbreviation E2 : 120V AC area in E model E3 : 240V AC area in E model E13 : Russian model and 220 – 230V AC area in E model E51 : Chilean and Peruvian models MX : Mexican model MY : Malaysia model Ref. No. Part No. Description Remark 8-1. CASE, ESCUTCHEON TOP SECTION Ref. No. Part No. Description Remark 1 2-655-708-51 PANEL, LOADING (ZX80D: US, E3, E13) 1 2-655-708-61 PANEL, LOADING (ZX100D: E3, SP, MY) 1 2-685-144-11 PANEL, LOADING (ZX80D: E2, MX) 1 2-685-144-21 PANEL, LOADING (ZX100D: E2, MX) 1 2-685-144-31 PANEL, LOADING (ZX80D: E51) 1 2-685-144-41 PANEL, LOADING (ZX100D: E51) 2 3-087-053-01 +BVTP2.6 (3CR) 3 2-662-067-01 BUTTON (SPEAKER) (SPEAKERS/X-ROUND OFF) 4 2-662-065-01 JOG (X-ROUND) 5 X-2108-715-1 ESCUTCHEON TOP ASSY (ZX80D: E2, E3, E13, E51, MX/ZX100D) 5 X-2177-645-1 ESCUTCHEON TOP ASSY (ZX80D: US) 6 3-363-099-02 SCREW (CASE 3 TP2) 7 3-363-099-32 SCREW (CASE 3 TP2) 8 2-342-137-51 CASE 9 4-225-252-21 CUSHION (FOOT) 10 3-077-331-01 +BV3 (3-CR) 11 4-237-065-01 CLAMP (L35) #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3 #2 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3 #4 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3 SP : Singapore model Ver. 1.1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 X-2108-713-1 KNOB VOLUME ASSY 52 X-2108-714-1 KNOB JOG ASSY 53 3-087-053-01 +BVTP2.6 (3CR) 54 A-1174-314-A FUNCTION BOARD, COMPLETE 55 1-828-991-11 WIRE (FLAT TYPE) (17 CORE) 56 A-1174-175-A PANEL BOARD, COMPLETE (ZX80D: MX/ZX100D: MX) 51 52 53 53 53 53 57 53 53 53 58 54 55 56 not supplied (JOG board) not supplied tape mecha deck section not supplied (CD-SW board) not supplied (ZX100D) 56 A-1174-312-A PANEL BOARD, COMPLETE (ZX80D: US, E2, E3, E13, E51/ZX100D: E2, E3, E51, SP, MY) 57 1-828-942-11 WIRE (FLAT TYPE) (7 CORE) 58 1-828-992-11 WIRE (FLAT TYPE) (17 CORE) Ver. 1.1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 101 4-224-578-31 KNOB (MIC) 102 2-655-724-21 LID (TC) 103 4-224-104-11 DAMPER 104 2-655-733-01 SPRING (L) 105 2-655-732-01 SPRING (LID) 106 2-655-734-01 SPRING (R) 107 3-087-053-01 +BVTP2.6 (3CR) 108 4-252-578-11 HOLDER TC-L 109 4-959-229-11 DETENT, CASSETTE 110 4-252-579-11 HOLDER TC-R 111 4-244-092-01 SPRING (EJECT) 112 3-077-331-21 +BV3 (3-CR) 113 1-417-658-11 MECHA DECK (CWN42RR603) 114 A-1174-047-A MIC BOARD, COMPLETE 115 1-828-964-11 WIRE (FLAT TYPE) (11 CORE) 116 4-225-252-21 CUSHION (FOOT) 117 X-2108-712-1 FRONT PANEL ASSY (ZX80D: E3, E13, E51/ZX100D: E3, E51, SP, MY) 117 X-2109-461-1 FRONT PANEL ASSY (ZX80D: E2, MX/ZX100D: E2, MX) 117 X-2176-353-1 FRONT PANEL ASSY (ZX80D: US) #5 7-685-853-04 SCREW +BVTT 2X6 (S) 101 not supplied not supplied not supplied not supplied not supplied #5 not supplied not supplied not supplied not supplied not supplied 116 116 102 103 117 103 104 105 106 107 115 107 107 107 112 107 107 107 108 109 109 110 111 113 114 Ver. 1.1 Ver. 1.1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 0151 1-468-737-51 POWER SWITCHING (ZX80D: E2, E3, E13, E51, MX/ZX100D) 0151 1-468-737-61 POWER SWITCHING (ZX80D: US) 152 1-693-702-11 TUNER (FM/AM) (TM10SE) (ZX80D: E2, E3, E13, E51, MX/ZX100D) 152 1-693-703-11 TUNER (FM/AM) (TM10SU) (ZX80D: US) 153 3-378-109-12 CUSHION, SARANET 154 1-828-358-11 WIRE (FLAT TYPE) (19 CORE) 155 A-1173-807-A EFFECTOR BOARD, COMPLETE (ZX80D: US, E2, E3, E13, E51/ ZX100D: E2, E3, E51, SP, MY) 155 A-1174-198-A EFFECTOR BOARD, COMPLETE (ZX80D: MX/ZX100D: MX) 151 159 159 #1 #1 #1 #1 #1 #2 #3 #4 #4 #4 #4 #4 #4 #4 #4 #4 not supplied not supplied not supplied not supplied not supplied not supplied not supplied DMB15/KARAOKE/VIDEO boards section MAIN/PA/SURROUND boards section not supplied not supplied (PRIMARY board) 158 156 (ZX100D) (ZX100D) 152 153 157 154 155 M501 156 1-828-973-11 WIRE (FLAT TYPE) (13 CORE) 157 1-828-956-11 WIRE (FLAT TYPE) (9 CORE) 158 3-701-748-00 CLAMP 159 4-237-065-01 CLAMP (L35) M501 1-787-400-11 D.C. FAN #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3 #2 7-685-648-79 SCREW +BVTP 3X12 TYPE2 IT-3 #3 7-685-651-79 SCREW +BVTP 3X20 TYPE2 N-S #4 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3 Ver. 1.1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 201 A-1193-305-A KARAOKE BOARD, COMPLETE (ZX80D: US, E2, E3, E13, E51/ ZX100D: E2, E3, E51, SP, MY) 201 A-1193-346-A KARAOKE BOARD, COMPLETE (ZX80D: MX/ZX100D: MX) 202 A-1174-061-A VIDEO BOARD, COMPLETE (ZX80D: US, E2, E3, E13, E51/ ZX100D: E2, E3, E51, SP, MY) 202 A-1174-224-A VIDEO BOARD, COMPLETE (ZX80D: MX/ZX100D: MX) 203 1-828-326-11 WIRE (FLAT TYPE) (13 CORE) 204 A-1174-227-A DMB15 BOARD, COMPLETE (ZX80D: MX/ZX100D: MX) 204 A-1174-274-A DMB15 BOARD, COMPLETE (ZX80D: E3, E13/ZX100D: E3) 201 #4 #4 #4 #4 #4 #4 not supplied not supplied DVD mechanism deck section-1 (CDM74HF-DVBU101) not supplied not supplied not supplied 202 203 208 206 209 210 210 209 205 207 204 (ZX80D: US) 204 A-1193-183-A DMB15 BOARD, COMPLETE (ZX100D: SP, MY) 204 A-1193-188-A DMB15 BOARD, COMPLETE (ZX80D: E2, E51/ZX100D: E2, E51) 204 A-1227-260-A DMB15 BOARD, COMPLETE (ZX80D: US) 205 1-828-332-11 WIRE (FLAT TYPE) (13 CORE) 206 1-828-632-11 WIRE (FLAT TYPE) (21 CORE) 207 1-828-252-11 WIRE (FLAT TYPE) (24 CORE) 208 3-577-414-01 SPACER (ZX80D: US) * 209 1-481-077-11 CORE, FERRITE (ZX80D: US) 210 3-381-709-01 CUSHION, SARANET (ZX80D: US) #4 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3 Note: Refer to the Servicing Notes “NOTES ON REPLACEMENT OF THE DMB15 BOARD” (pagr 4), if replacing the Ref. No. 204. Ver. 1.1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 251 4-225-252-01 CUSHION (FOOT) 252 4-900-386-01 SCREW 253 3-077-331-21 +BV3 (3-CR) 254 A-1174-202-A PA BOARD, COMPLETE (ZX80D: MX) 254 A-1174-267-A PA BOARD, COMPLETE (ZX100D: MX) 254 A-1174-326-A PA BOARD, COMPLETE (ZX80D: E3, E13) 254 A-1174-337-A PA BOARD, COMPLETE (ZX100D: E3, SP, MY) 254 A-1193-201-A PA BOARD, COMPLETE (ZX80D: US, E2, E51) 254 A-1193-204-A PA BOARD, COMPLETE (ZX100D: E2, E51) 255 3-905-609-31 SCREW (TRANSISTOR) 256 A-1174-185-A SURROUND BOARD, COMPLETE (ZX80D: MX) 256 A-1174-262-A SURROUND BOARD, COMPLETE (ZX100D: MX) 256 A-1174-323-A SURROUND BOARD, COMPLETE (ZX80D: US, E2, E3, E13, E51) 256 A-1174-333-A SURROUND BOARD, COMPLETE (ZX100D: E2, E3, E51, SP, MY) 257 A-1174-078-A MAIN BOARD, COMPLETE (ZX80D: E3) 257 A-1174-169-A MAIN BOARD, COMPLETE (ZX80D: MX) 257 A-1174-256-A MAIN BOARD, COMPLETE (ZX100D: MX) 257 A-1174-328-A MAIN BOARD, COMPLETE (ZX100D: E3) 257 A-1193-164-A MAIN BOARD, COMPLETE (ZX80D: E13) 257 A-1193-167-A MAIN BOARD, COMPLETE (ZX80D: E2) 257 A-1193-171-A MAIN BOARD, COMPLETE (ZX100D: SP, MY) 257 A-1193-174-A MAIN BOARD, COMPLETE (ZX100D: E2) 257 A-1193-435-A MAIN BOARD, COMPLETE (ZX80D: E51) 257 A-1193-438-A MAIN BOARD, COMPLETE (ZX100D: E51) 257 A-1227-251-A MAIN BOARD, COMPLETE (ZX80D: US) 0258 1-777-071-53 CORD, POWER (ZX80D: E2, E3, E13, E51/ ZX100D: E2, E3, E51, SP, MY) 0258 1-783-820-11 CORD, POWER (ZX80D: US) 0258 1-829-627-31 POWER-SUPPLY CORD (ZX80D: MX/ZX100D: MX) * 259 3-703-244-00 BUSHING (2104), CORD (ZX80D: US, E2, E3, E13, E51/ ZX100D: E2, E3, E51, SP, MY) 259 3-703-571-11 BUSHING (S) (4516), CORD (ZX80D: MX/ ZX100D: MX) D656 8-719-073-32 DIODE D25XB60 D658 8-719-066-42 DIODE RBV1306 (ZX80D) D658 8-719-073-32 DIODE D25XB60 (ZX100D) M502 1-787-400-11 D.C. FAN #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3 #4 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3 251 #1 #1 #4 #4 #4 #4 #4 #4 #4 #4 not supplied not supplied M502 not supplied not supplied D656 D658 not supplied not supplied not supplied not supplied not supplied POWER TRANSFORMER section not supplied 251 252 252 252 253 253 253 253 253 253 253 253 254 255 255 255 256 257 258 259 Ver. 1.1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 301 A-1174-058-A TRANS BOARD, COMPLETE (ZX100D: E2, E3, E51, SP, MY) 301 A-1174-204-A TRANS BOARD, COMPLETE (ZX80D: MX) 301 A-1174-927-A TRANS BOARD, COMPLETE (ZX80D: E2, E3, E13, E51) 301 A-1174-928-A TRANS BOARD, COMPLETE (ZX100D: MX) 301 A-1227-256-A TRANS BOARD, COMPLETE (ZX80D: US) 0F1241 1-533-949-33 FUSE, CYLINDRICAL (TIME LUG) (8A/250V) (ZX80D: E2, E3, E13, E51, MX/ZX100D) 0F1241 1-576-537-12 FUSE, GLASS TUBE (DIA. 5) (8A/125V) (ZX80D: US) 0F1251 1-533-949-33 FUSE, CYLINDRICAL (TIME LUG) (8A/250V) (ZX80D: E2, E3, E13, E51, MX/ZX100D) 0F1251 1-576-537-12 FUSE, GLASS TUBE (DIA. 5) (8A/125V) (ZX80D: US) 0F1261 1-533-949-33 FUSE, CYLINDRICAL (TIME LUG) (8A/250V) (ZX80D: E2, E3, E13, E51, MX/ZX100D) 0F1261 1-576-537-12 FUSE, GLASS TUBE (DIA. 5) (8A/125V) (ZX80D: US) 0F1271 1-533-949-33 FUSE, CYLINDRICAL (TIME LUG) (8A/250V) (ZX80D: E2, E3, E13, E51, MX/ZX100D) 0F1271 1-576-537-12 FUSE, GLASS TUBE (DIA. 5) (8A/125V) (ZX80D: US) 0F1281 1-532-465-33 FUSE (3.15A/250V) (ZX80D: E2, E3, E13, E51, MX/ZX100D) 0F1281 1-533-451-12 FUSE, GLASS TUBE (DIA. 5) (3.15A/125V) (ZX80D: US) 0F1291 1-532-465-33 FUSE (3.15A/250V) (ZX80D: E2, E3, E13, E51, MX/ZX100D) 0F1291 1-533-451-12 FUSE, GLASS TUBE (DIA. 5) (3.15A/125V) (ZX80D: US) 0T1200 1-443-977-11 POWER TRANSFORMER (ZX100D: E2, E3, E51, SP, MY) 0T1200 1-443-978-11 POWER TRANSFORMER (ZX100D: MX) 0T1200 1-445-024-11 POWER TRANSFORMER (ZX80D: E2, E3, E13, E51) 0T1200 1-445-025-11 POWER TRANSFORMER (ZX80D: MX) 0T1200 1-445-153-11 POWER TRANSFORMER (ZX80D: US) 301 F1241 F1251 F1261 F1271 F1281 F1291 T1200 Ver. 1.1

(CDM74HF-DVBU101) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 501 4-218-253-42 SCREW (M2.6), +BTTP 502 1-776-182-11 WIRE (FLAT TYPE) (5 CORE) 503 1-687-134-12 MOTOR (TB) BOARD 504 4-243-815-11 TABLE (LOADING) 505 4-245-571-02 GEAR (STOPPER) 506 4-218-252-61 SCREW (+PTPWH M2.6), FLOATING 507 4-245-570-01 GEAR (JOINT) 508 4-245-572-01 BUSHING (GEAR) 509 1-687-132-12 SENSOR BOARD 510 4-243-820-01 GEAR (TABLE) 511 4-243-819-01 GEAR (GENEVA) 512 4-243-816-21 TRAY 513 4-243-823-01 BELT (TABLE) 514 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING 515 4-243-821-01 PULLEY (TABLE) 516 3-231-598-01 SHEET (BA) M741 A-1108-965-A MOTOR ASSY, TABLE 504 505 505 506 506 507 507 508 508 509 501 512 506 513 514 515 510 511 514 DVD mechanism deck section-2 (CDM74HF-DVBU101) 501 502 503 516 M741

(CDM74HF-DVBU101) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 551 4-251-923-01 YOKE (310) 552 4-218-253-32 SCREW (M2.6), +BTTP 553 1-687-669-12 SW BOARD 554 4-244-034-01 BELT (LOADING) 555 4-218-252-52 SCREW (+PTPWH M2.6), FLOATING 556 4-225-844-01 GEAR (LOADING A) 557 4-224-613-01 GEAR (SHAFT) 558 1-687-133-12 MOTOR (LD) BOARD 559 3-087-599-01 INSULATOR SCREW 560 4-244-108-01 GEAR, SWING 561 4-224-609-01 GEAR (LOADING C) 562 4-224-608-01 COLLAR, SWING 563 3-016-533-11 WASHER (FR), STOPPER 564 4-224-611-01 GEAR (LOADING B) 565 4-224-606-01 GEAR (RV) 566 4-243-818-01 GEAR (U/D) 567 2-541-918-01 LEVER (LIFTER (H)) 568 2-345-982-01 PULLEY A (310), CHUCKING 569 2-345-983-01 PULLEY B (310), CHUCKING 570 2-634-618-01 INSULATOR 0571 8-820-291-02 OPTICAL PICK-UP BLOCK (KHM-310CAB/ C2RP) (Including sled motor, spindle motor) 0571 8-820-322-04 OPTICAL PICK-UP BLOCK (KHM-313CAB/ C2RP) (Including sled motor, spindle motor) 572 4-243-817-22 CHASSIS M751 A-4737-553-A MOTOR ASSY, LOADING S711 1-477-680-12 ENCODER, ROTARY (DISC TABLE ADDRESS DETECT) 551 552 552 552 553 554 555 556 557 558 560 561 562 563 564 565 566 567 572 569 559 568 555 555 555 555 M751 S711 570 570 559 not supplied (DRIVER board) not supplied not supplied 571 (including sled motor, spindle motor) not supplied (spindle motor) not supplied (sled motor) Note: Refer to the Servicing Notes “HOW TO IDENTIFY OPTICAL PICK-UP BLOCK” (pagr 4), if replacing the Ref. No. 571.

CD-SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CD-SW BOARD ************* < CONNECTOR > CN1152 1-568-850-11 SOCKET, CONNECTOR 7P < RESISTOR > R1166 1-216-817-11 METAL CHIP 470 5% 1/10W R1167 1-216-819-11 METAL CHIP 680 5% 1/10W R1168 1-216-821-11 METAL CHIP 1K 5% 1/10W R1169 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R1170 1-216-823-11 METAL CHIP 1.5K 5% 1/10W < SWITCH > S1166 1-762-875-21 SWITCH, KEYBOARD (Z OPEN/CLOSE) S1167 1-762-875-21 SWITCH, KEYBOARD (EX-CHANGE/DISC SKIP) S1168 1-762-875-21 SWITCH, KEYBOARD (DISC 3) S1169 1-762-875-21 SWITCH, KEYBOARD (DISC 2) S1170 1-762-875-21 SWITCH, KEYBOARD (DISC 1) ************************************************************ A-1174-227-A DMB15 BOARD, COMPLETE (ZX80D: MX/ZX100D: MX) A-1174-274-A DMB15 BOARD, COMPLETE (ZX80D: E3, E13/ZX100D: E3) A-1193-183-A DMB15 BOARD, COMPLETE (ZX100D: SP, MY) A-1193-188-A DMB15 BOARD, COMPLETE (ZX80D: E2, E51/ZX100D: E2, E51) A-1227-260-A DMB15 BOARD, COMPLETE (ZX80D: US) ********************** < CAPACITOR > C101 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C102 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C105 1-126-205-11 ELECT CHIP 47uF 20% 6.3V C106 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C108 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C109 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C112 1-126-205-11 ELECT CHIP 47uF 20% 6.3V C113 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C114 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C115 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C116 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C117 1-124-779-00 ELECT CHIP 10uF 20% 16V C118 1-124-779-00 ELECT CHIP 10uF 20% 16V C119 1-124-779-00 ELECT CHIP 10uF 20% 16V C120 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C121 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C122 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C123 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C124 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C125 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C126 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C127 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C128 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V C129 1-124-779-00 ELECT CHIP 10uF 20% 16V C130 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C131 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V C132 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C133 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C135 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V C136 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C137 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C138 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C139 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C140 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C144 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C146 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C147 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C148 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C149 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C150 1-124-779-00 ELECT CHIP 10uF 20% 16V C151 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V C152 1-162-916-11 CERAMIC CHIP 12PF 5% 50V C153 1-162-916-11 CERAMIC CHIP 12PF 5% 50V C154 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C155 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C156 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C158 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C159 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C160 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C161 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C162 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C163 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C164 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C167 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C170 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C171 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C172 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u: µ, for example: uA... : µA... uPA... : µPA... uPB... : µPB... uPC... : µPC... uPD... : µPD... • CAPACITORS uF: µF • COILS uH: µH The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board. • Abbreviation E2 : 120V AC area in E model E3 : 240V AC area in E model E13 : Russian model and 220 – 230V AC area in E model E51 : Chilean and Peruvian models MX : Mexican model MY : Malaysia model SP : Singapore model New part of EEPROM (IC103) on the DMB15 board cannot be used. Therefore, if the mounted DMB15 board is replaced, exchange new EEPROM with that used before the replacement. Ver. 1.1

CN101 1-815-763-32 CONNECTOR, FFC/FPC 24P * CN105 1-770-470-21 PIN, CONNECTOR (PC BOARD) 6P CN106 1-784-372-51 CONNECTOR, FFC/FPC 13P * CN201 1-770-470-21 PIN, CONNECTOR (PC BOARD) 6P CN301 1-784-372-51 CONNECTOR, FFC/FPC 13P CN302 1-778-692-11 CONNECTOR, FFC/FPC 21P CN401 1-779-993-11 PIN, CONNECTOR (PWB) 5P < DIODE > D1001 8-719-058-24 DIODE RB501V-40TE-17 D3501 8-719-988-61 DIODE 1SS355TE-17 Ver. 1.1

FB111 1-414-226-21 INDUCTOR, FERRITE BEAD FB112 1-414-226-21 INDUCTOR, FERRITE BEAD FB113 1-414-226-21 INDUCTOR, FERRITE BEAD FB114 1-414-226-21 INDUCTOR, FERRITE BEAD FB115 1-414-226-21 INDUCTOR, FERRITE BEAD FB401 1-469-324-21 FERRITE, EMI (SMD) (2012) FB402 1-469-324-21 FERRITE, EMI (SMD) (2012) FB403 1-469-324-21 FERRITE, EMI (SMD) (2012) FB404 1-469-324-21 FERRITE, EMI (SMD) (2012) FB405 1-469-324-21 FERRITE, EMI (SMD) (2012) FB406 1-469-324-21 FERRITE, EMI (SMD) (2012) < FILTER > FL101 1-234-177-21 FILTER, CHIP EMI FL104 1-234-177-21 FILTER, CHIP EMI FL105 1-234-177-21 FILTER, CHIP EMI FL106 1-234-177-21 FILTER, CHIP EMI FL107 1-234-177-21 FILTER, CHIP EMI FL108 1-234-177-21 FILTER, CHIP EMI FL401 1-234-177-21 FILTER, CHIP EMI FL402 1-233-893-21 FILTER, CHIP EMI FL403 1-234-177-21 FILTER, CHIP EMI < IC > IC101 6-806-614-01 IC S29AL032D70TF-CBA3-0601UC (ZX80D: MX/ZX100D: MX) IC101 6-806-820-01 IC MX29LV320CBTC70-CBA3-0604UC (ZX80D: US, E2, E51/ZX100D: E2, E51) IC101 6-806-821-01 IC MX29LV320CBTC70-CBA3-0604CE (ZX80D: E3, E13/ZX100D: E3) IC101 6-806-822-01 IC MX29LV320CBTC70-CBA3-0604GA (ZX100D: SP, MY) IC102 6-707-535-01 IC CXD9849R IC103 (Not supplied) IC BR24L64F-WE2 IC104 6-709-370-01 IC A2V64S40CTP-G75 IC105 6-702-302-01 IC TK11133CSCL-G IC106 6-708-153-01 IC PQ018EN01ZPH IC107 6-702-302-01 IC TK11133CSCL-G IC201 6-704-524-01 IC FAN8036L IC301 6-704-222-01 IC AK4358VQ-L IC3601 6-707-608-01 IC PCM1803DBR IC3711 8-759-359-49 IC NJM3414AV (TE2) IC3731 8-759-359-49 IC NJM3414AV (TE2) IC3751 8-759-359-49 IC NJM3414AV (TE2) IC3771 8-759-359-49 IC NJM3414AV (TE2) < COIL > L3601 1-469-555-21 INDUCTOR 10uH L3602 1-469-555-21 INDUCTOR 10uH < TRANSISTOR > Q101 6-550-008-01 FET UM6K1N-TN Q102 6-550-653-01 TRANSISTOR QST8TR Q103 8-729-027-52 TRANSISTOR DTC124EKA-T146 Q3801 8-729-230-49 TRANSISTOR 2SC2712-YG < RESISTOR/FERRITE BEAD > R101 1-216-809-11 METAL CHIP 100 5% 1/10W R104 1-216-864-11 SHORT CHIP 0 R105 1-216-833-11 METAL CHIP 10K 5% 1/10W R106 1-216-833-11 METAL CHIP 10K 5% 1/10W R107 1-216-833-11 METAL CHIP 10K 5% 1/10W R108 1-216-857-11 METAL CHIP 1M 5% 1/10W R109 1-216-864-11 SHORT CHIP 0 R110 1-216-841-11 METAL CHIP 47K 5% 1/10W R111 1-216-809-11 METAL CHIP 100 5% 1/10W R112 1-211-977-11 METAL CHIP 22 0.5% 1/10W R113 1-211-977-11 METAL CHIP 22 0.5% 1/10W R114 1-216-845-11 METAL CHIP 100K 5% 1/10W R115 1-211-977-11 METAL CHIP 22 0.5% 1/10W R116 1-216-821-11 METAL CHIP 1K 5% 1/10W R117 1-216-841-11 METAL CHIP 47K 5% 1/10W R118 1-216-801-11 METAL CHIP 22 5% 1/10W R120 1-216-801-11 METAL CHIP 22 5% 1/10W R121 1-216-801-11 METAL CHIP 22 5% 1/10W R123 1-216-864-11 SHORT CHIP 0 R124 1-216-841-11 METAL CHIP 47K 5% 1/10W R126 1-216-864-11 SHORT CHIP 0 R127 1-216-809-11 METAL CHIP 100 5% 1/10W R136 1-216-835-11 METAL CHIP 15K 5% 1/10W R138 1-216-845-11 METAL CHIP 100K 5% 1/10W R141 1-218-916-11 METAL CHIP 750K 0.5% 1/10W R142 1-216-845-11 METAL CHIP 100K 5% 1/10W R146 1-216-805-11 METAL CHIP 47 5% 1/10W R151 1-216-805-11 METAL CHIP 47 5% 1/10W R152 1-216-864-11 SHORT CHIP 0 R153 1-216-805-11 METAL CHIP 47 5% 1/10W R155 1-216-805-11 METAL CHIP 47 5% 1/10W R160 1-216-805-11 METAL CHIP 47 5% 1/10W R161 1-216-809-11 METAL CHIP 100 5% 1/10W R164 1-216-809-11 METAL CHIP 100 5% 1/10W R169 1-216-833-11 METAL CHIP 10K 5% 1/10W R187 1-216-864-11 SHORT CHIP 0 R189 1-218-827-11 METAL CHIP 150 0.5% 1/10W R190 1-218-827-11 METAL CHIP 150 0.5% 1/10W R191 1-216-821-11 METAL CHIP 1K 5% 1/10W R192 1-218-827-11 METAL CHIP 150 0.5% 1/10W R193 1-216-821-11 METAL CHIP 1K 5% 1/10W R195 1-218-827-11 METAL CHIP 150 0.5% 1/10W R196 1-216-864-11 SHORT CHIP 0 R197 1-218-827-11 METAL CHIP 150 0.5% 1/10W R204 1-216-822-11 METAL CHIP 1.2K 5% 1/10W R205 1-216-833-11 METAL CHIP 10K 5% 1/10W R206 1-216-833-11 METAL CHIP 10K 5% 1/10W R207 1-216-826-11 METAL CHIP 2.7K 5% 1/10W R208 1-216-839-11 METAL CHIP 33K 5% 1/10W R209 1-216-839-11 METAL CHIP 33K 5% 1/10W R210 1-216-841-11 METAL CHIP 47K 5% 1/10W R212 1-216-833-11 METAL CHIP 10K 5% 1/10W R213 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R214 1-216-835-11 METAL CHIP 15K 5% 1/10W New part of EEPROM (IC103) on the DMB15 board cannot be used. Therefore, if the mounted DMB15 board is replaced, exchange new EEPROM with that used before the replacement. Ver. 1.1

R1524 1-216-864-11 SHORT CHIP 0 R1526 1-216-864-11 SHORT CHIP 0 R1527 1-216-864-11 SHORT CHIP 0 R1530 1-216-864-11 SHORT CHIP 0 R1531 1-216-864-11 SHORT CHIP 0 R1540 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1542 1-216-833-11 METAL CHIP 10K 5% 1/10W R1543 1-216-833-11 METAL CHIP 10K 5% 1/10W R1544 1-216-864-11 SHORT CHIP 0 R1546 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R1547 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1548 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1549 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1550 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1551 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1553 1-216-864-11 SHORT CHIP 0 R1554 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1557 1-216-809-11 METAL CHIP 100 5% 1/10W R1559 1-216-833-11 METAL CHIP 10K 5% 1/10W R2504 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R3504 1-216-809-11 METAL CHIP 100 5% 1/10W R3505 1-216-809-11 METAL CHIP 100 5% 1/10W R3601 1-216-809-11 METAL CHIP 100 5% 1/10W R3602 1-216-809-11 METAL CHIP 100 5% 1/10W R3603 1-216-833-11 METAL CHIP 10K 5% 1/10W R3605 1-216-864-11 SHORT CHIP 0 R3606 1-216-864-11 SHORT CHIP 0 R3607 1-216-864-11 SHORT CHIP 0 R3609 1-216-864-11 SHORT CHIP 0 R3611 1-216-809-11 METAL CHIP 100 5% 1/10W R3621 1-216-809-11 METAL CHIP 100 5% 1/10W R3651 1-216-864-11 SHORT CHIP 0 R3652 1-216-864-11 SHORT CHIP 0 R3653 1-216-864-11 SHORT CHIP 0 R3711 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R3712 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R3713 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R3714 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R3715 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R3716 1-216-821-11 METAL CHIP 1K 5% 1/10W R3717 1-216-821-11 METAL CHIP 1K 5% 1/10W R3718 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R3719 1-216-821-11 METAL CHIP 1K 5% 1/10W R3721 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R3722 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R3723 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R3724 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R3725 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R3726 1-216-821-11 METAL CHIP 1K 5% 1/10W R3727 1-216-821-11 METAL CHIP 1K 5% 1/10W R3728 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R3729 1-216-821-11 METAL CHIP 1K 5% 1/10W R3731 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R3732 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R3733 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R3734 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R3735 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R3736 1-216-821-11 METAL CHIP 1K 5% 1/10W R3737 1-216-821-11 METAL CHIP 1K 5% 1/10W R3738 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R3739 1-216-821-11 METAL CHIP 1K 5% 1/10W R3741 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R3742 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R3743 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R3744 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R3745 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R3746 1-216-821-11 METAL CHIP 1K 5% 1/10W R3747 1-216-821-11 METAL CHIP 1K 5% 1/10W R3748 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R3749 1-216-821-11 METAL CHIP 1K 5% 1/10W R3751 1-216-823-11 METAL CHIP 1.5K 5% 1/10W DMB15

R5016 1-216-864-11 SHORT CHIP 0 (ZX80D: E3, E13/ZX100D: E3) R5017 1-216-864-11 SHORT CHIP 0 (ZX100D: SP, MY) < COMPOSITION CIRCUIT BLOCK > RB103 1-234-795-21 RES, NETWORK 0X4 (2010) RB104 1-234-795-21 RES, NETWORK 0X4 (2010) RB105 1-234-371-21 RES, NETWORK 47 (1005X4) RB106 1-234-371-21 RES, NETWORK 47 (1005X4) RB107 1-234-370-21 RES, NETWORK 22 (1005X4) RB108 1-234-370-21 RES, NETWORK 22 (1005X4) RB111 1-234-795-21 RES, NETWORK 0X4 (2010) RB112 1-234-370-21 RES, NETWORK 22 (1005X4) RB113 1-234-370-21 RES, NETWORK 22 (1005X4) < VIBRATOR > X101 1-781-867-21 VIBRATOR, CRYSTAL (27MHz) ************************************************************ DRIVER BOARD ************* < CAPACITOR > C715 1-126-933-11 ELECT 100uF 20% 16V C731 1-126-964-11 ELECT 10uF 20% 50V C735 1-164-159-11 CERAMIC 0.1uF 50V C736 1-164-159-11 CERAMIC 0.1uF 50V C737 1-164-159-11 CERAMIC 0.1uF 50V C741 1-162-306-11 CERAMIC 0.01uF 20% 16V C751 1-162-306-11 CERAMIC 0.01uF 20% 16V C752 1-164-159-11 CERAMIC 0.1uF 50V < CONNECTOR > CN701 1-784-735-11 CONNECTOR, FFC 13P CN702 1-784-766-11 CONNECTOR, FFC 5P * CN703 1-564-720-11 PIN, CONNECTOR (SMALL TYPE) 4P CN704 1-785-328-11 PIN, CONNECTOR (LIGHT ANGRE) 2P < DIODE > D701 8-719-947-16 DIODE MTZJ-T-72-5.1A D711 8-719-983-66 DIODE MTZJ-T-72-3.6B < IC > IC701 8-759-598-69 IC BA6956AN IC712 8-759-598-69 IC BA6956AN < TRANSISTOR > Q731 8-729-029-66 TRANSISTOR DTC114ESA < RESISTOR > R701 1-249-413-11 CARBON 470 5% 1/4W R702 1-247-807-31 CARBON 100 5% 1/4W R711 1-249-417-11 CARBON 1K 5% 1/4W R712 1-247-847-11 CARBON 4.7K 5% 1/4W R713 1-247-863-11 CARBON 22K 5% 1/4W R721 1-247-847-11 CARBON 4.7K 5% 1/4W R722 1-247-847-11 CARBON 4.7K 5% 1/4W R723 1-247-847-11 CARBON 4.7K 5% 1/4W R731 1-247-807-31 CARBON 100 5% 1/4W R732 1-249-429-11 CARBON 10K 5% 1/4W R733 1-249-417-11 CARBON 1K 5% 1/4W R734 1-249-430-11 CARBON 12K 5% 1/4W R736 1-249-412-11 CARBON 390 5% 1/4W R751 1-247-847-11 CARBON 4.7K 5% 1/4W ************************************************************ DMB15 DRIVER Ver. 1.1

E3, E13, E51/ZX100D: E2, E3, E51, SP, MY) A-1174-198-A EFFECTOR BOARD, COMPLETE (ZX80D: MX/ZX100D: MX) ************************* < CAPACITOR > C1511 1-164-156-11 CERAMIC CHIP 0.1uF 25V C1512 1-136-165-00 FILM 0.1uF 5% 50V C1513 1-164-156-11 CERAMIC CHIP 0.1uF 25V C1514 1-164-156-11 CERAMIC CHIP 0.1uF 25V C1515 1-126-947-11 ELECT 47uF 20% 35V C1517 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V C1518 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V C1519 1-136-159-00 FILM 0.033uF 5% 50V C1520 1-162-961-11 CERAMIC CHIP 330PF 10% 50V C1521 1-162-961-11 CERAMIC CHIP 330PF 10% 50V C1522 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V C1524 1-126-957-11 ELECT 0.22uF 20% 50V C1525 1-126-957-11 ELECT 0.22uF 20% 50V C1526 1-136-165-00 FILM 0.1uF 5% 50V C1527 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V C1528 1-104-665-11 ELECT 100uF 20% 25V C1529 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V C1530 1-136-159-00 FILM 0.033uF 5% 50V C1531 1-124-589-11 ELECT 47uF 20% 16V C1533 1-162-961-11 CERAMIC CHIP 330PF 10% 50V C1534 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V C1535 1-136-159-00 FILM 0.033uF 5% 50V C1536 1-162-961-11 CERAMIC CHIP 330PF 10% 50V C1537 1-136-165-00 FILM 0.1uF 5% 50V C1540 1-126-957-11 ELECT 0.22uF 20% 50V C1541 1-126-957-11 ELECT 0.22uF 20% 50V C1542 1-130-479-00 MYLAR 0.0047uF 5% 50V C1543 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V C1544 1-130-479-00 MYLAR 0.0047uF 5% 50V C1545 1-126-964-11 ELECT 10uF 20% 50V C1546 1-126-964-11 ELECT 10uF 20% 50V C1547 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V C1548 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C1552 1-126-964-11 ELECT 10uF 20% 50V C1554 1-126-964-11 ELECT 10uF 20% 50V C1555 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C1559 1-126-964-11 ELECT 10uF 20% 50V C1560 1-126-964-11 ELECT 10uF 20% 50V C1561 1-126-964-11 ELECT 10uF 20% 50V C1562 1-126-964-11 ELECT 10uF 20% 50V C1568 1-164-156-11 CERAMIC CHIP 0.1uF 25V C1570 1-126-964-11 ELECT 10uF 20% 50V C1571 1-164-156-11 CERAMIC CHIP 0.1uF 25V C1572 1-164-156-11 CERAMIC CHIP 0.1uF 25V C1574 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V C1578 1-126-964-11 ELECT 10uF 20% 50V C1584 1-104-665-11 ELECT 100uF 20% 25V C1600 1-164-156-11 CERAMIC CHIP 0.1uF 25V C1601 1-126-964-11 ELECT 10uF 20% 50V C1602 1-126-964-11 ELECT 10uF 20% 50V C2330 1-136-165-00 FILM 0.1uF 5% 50V C2331 1-136-159-00 FILM 0.033uF 5% 50V < CONNECTOR > CN1502 1-779-287-11 FFC CONNECTOR (LIF (NON-ZIF)) 19P < DIODE > D1502 6-501-169-01 DIODE UDZW-TE17-6.2B D1503 8-719-404-50 DIODE MA111-TX D1504 8-719-404-50 DIODE MA111-TX D1505 8-719-404-50 DIODE MA111-TX D1506 8-719-404-50 DIODE MA111-TX D1507 8-719-404-50 DIODE MA111-TX D1508 8-719-404-50 DIODE MA111-TX < IC > IC1501 8-759-496-41 IC M65850FP-E1 IC1502 6-709-217-01 IC TC74LVX4051FT IC1503 6-709-217-01 IC TC74LVX4051FT IC1504 8-759-496-41 IC M65850FP-E1 IC1505 8-759-710-97 IC NJM4565M-D IC1506 6-709-218-01 IC TC74LVX4052FT < COIL > L1500 1-414-183-41 INDUCTOR 10uH < TRANSISTOR > Q1500 8-729-055-10 FET 2SK3378ENTL Q1501 8-729-055-10 FET 2SK3378ENTL Q1502 8-729-055-10 FET 2SK3378ENTL Q1503 8-729-055-10 FET 2SK3378ENTL Q1504 8-729-055-10 FET 2SK3378ENTL Q1505 8-729-055-10 FET 2SK3378ENTL Q1506 8-729-055-10 FET 2SK3378ENTL Q1507 8-729-056-46 TRANSISTOR 2SC5053T100Q Q1508 8-729-055-10 FET 2SK3378ENTL Q1509 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q1510 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q1511 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q1512 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q1513 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q1514 8-729-027-43 TRANSISTOR DTC114EKA-T146 < RESISTOR > R1500 1-216-809-11 METAL CHIP 100 5% 1/10W R1501 1-216-809-11 METAL CHIP 100 5% 1/10W R1502 1-216-809-11 METAL CHIP 100 5% 1/10W R1504 1-216-809-11 METAL CHIP 100 5% 1/10W R1506 1-216-809-11 METAL CHIP 100 5% 1/10W R1507 1-216-809-11 METAL CHIP 100 5% 1/10W R1510 1-216-836-11 METAL CHIP 18K 5% 1/10W R1511 1-216-836-11 METAL CHIP 18K 5% 1/10W R1512 1-216-836-11 METAL CHIP 18K 5% 1/10W R1514 1-216-836-11 METAL CHIP 18K 5% 1/10W R1515 1-216-836-11 METAL CHIP 18K 5% 1/10W R1516 1-216-833-11 METAL CHIP 10K 5% 1/10W R1517 1-216-833-11 METAL CHIP 10K 5% 1/10W R1519 1-216-840-11 METAL CHIP 39K 5% 1/10W EFFECTOR Ver. 1.1

************************* < CAPACITOR > C907 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < CONNECTOR > * CN901 1-569-934-11 SOCKET, CONNECTOR 17P < HEADER > CNS902 1-820-050-11 BOARD TO BOARD HEADER (8P) < LED > D1016 6-500-727-01 LED SLR-343DCT32 (DELAY) D1017 6-500-727-01 LED SLR-343DCT32 (CHORUS) D1020 6-500-727-01 LED SLR-343DCT32 (FLANGER) < JUMPER RESISTOR > JR921 1-216-864-11 SHORT CHIP 0 JR923 1-216-864-11 SHORT CHIP 0 < TRANSISTOR > Q920 8-729-027-50 TRANSISTOR DTC123JKA-T146 Q921 8-729-027-50 TRANSISTOR DTC123JKA-T146 < RESISTOR > R958 1-216-819-11 METAL CHIP 680 5% 1/10W R959 1-216-821-11 METAL CHIP 1K 5% 1/10W R960 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R961 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R962 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R963 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R972 1-216-821-11 METAL CHIP 1K 5% 1/10W R973 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R1001 1-216-817-11 METAL CHIP 470 5% 1/10W R1002 1-216-819-11 METAL CHIP 680 5% 1/10W R1003 1-216-821-11 METAL CHIP 1K 5% 1/10W R1004 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R1005 1-216-823-11 METAL CHIP 1.5K 5% 1/10W FUNCTION EFFECTOR

S901 1-762-875-21 SWITCH, KEYBOARD (PROGRESSIVE) S902 1-762-875-21 SWITCH, KEYBOARD (GROOVE) S903 1-762-875-21 SWITCH, KEYBOARD (EQ BAND) S904 1-762-875-21 SWITCH, KEYBOARD (DIRECTION) S905 1-762-875-21 SWITCH, KEYBOARD (REC PAUSE/START) S906 1-762-875-21 SWITCH, KEYBOARD (CD SYNC) S914 1-762-875-21 SWITCH, KEYBOARD (ENTER) S915 1-762-875-21 SWITCH, KEYBOARD (DELAY) S916 1-762-875-21 SWITCH, KEYBOARD (CHORUS) S917 1-762-875-21 SWITCH, KEYBOARD (FLANGER) S918 1-762-875-21 SWITCH, KEYBOARD (SOUND FIELD) S919 1-762-875-21 SWITCH, KEYBOARD (ILLUMINATION) S920 1-762-875-21 SWITCH, KEYBOARD (AMP MENU) S928 1-762-875-21 SWITCH, KEYBOARD (DISPLAY) S970 1-418-725-51 ENCODER, ROTARY (12 TYPE) (MASTER VOLUME) ************************************************************ JOG BOARD ********** < CAPACITOR > C1150 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < CONNECTOR > CNS903 1-562-573-31 SOCKET, CONNECTOR 8P < LED > D919 8-719-064-63 LED SELU5823C-TP15 (VOLUME LEVEL 1) D920 8-719-064-63 LED SELU5823C-TP15 (VOLUME LEVEL 2) D921 8-719-064-63 LED SELU5823C-TP15 (VOLUME LEVEL 3) D922 8-719-064-63 LED SELU5823C-TP15 (VOLUME LEVEL 4) D923 8-719-064-63 LED SELU5823C-TP15 (VOLUME LEVEL 5) D924 8-719-064-63 LED SELU5823C-TP15 (VOLUME LEVEL 6) D925 8-719-064-63 LED SELU5823C-TP15 (VOLUME LEVEL 7) D926 8-719-064-63 LED SELU5823C-TP15 (VOLUME LEVEL 8) < JUMPER RESISTOR > JR1 1-216-864-11 SHORT CHIP 0 JR2 1-216-864-11 SHORT CHIP 0 JR3 1-216-864-11 SHORT CHIP 0 JR4 1-216-864-11 SHORT CHIP 0 JR5 1-216-864-11 SHORT CHIP 0 JR922 1-216-864-11 SHORT CHIP 0 JR1096 1-216-864-11 SHORT CHIP 0 < TRANSISTOR > Q911 8-729-027-50 TRANSISTOR DTC123JKA-T146 Q912 8-729-027-50 TRANSISTOR DTC123JKA-T146 Q913 8-729-027-50 TRANSISTOR DTC123JKA-T146 Q915 8-729-027-50 TRANSISTOR DTC123JKA-T146 < RESISTOR > R1040 1-216-821-11 METAL CHIP 1K 5% 1/10W R1144 1-216-821-11 METAL CHIP 1K 5% 1/10W R1145 1-216-821-11 METAL CHIP 1K 5% 1/10W R1146 1-216-821-11 METAL CHIP 1K 5% 1/10W R1149 1-216-821-11 METAL CHIP 1K 5% 1/10W R1150 1-216-821-11 METAL CHIP 1K 5% 1/10W R1151 1-216-821-11 METAL CHIP 1K 5% 1/10W R1153 1-216-821-11 METAL CHIP 1K 5% 1/10W R1154 1-216-821-11 METAL CHIP 1K 5% 1/10W R1155 1-216-821-11 METAL CHIP 1K 5% 1/10W R1157 1-216-821-11 METAL CHIP 1K 5% 1/10W R1158 1-216-821-11 METAL CHIP 1K 5% 1/10W R1159 1-216-821-11 METAL CHIP 1K 5% 1/10W R1161 1-216-821-11 METAL CHIP 1K 5% 1/10W R1162 1-216-809-11 METAL CHIP 100 5% 1/10W R1163 1-216-809-11 METAL CHIP 100 5% 1/10W R1164 1-216-809-11 METAL CHIP 100 5% 1/10W R1165 1-216-809-11 METAL CHIP 100 5% 1/10W < ROTARY ENCODER > S1161 1-479-203-11 ENCODER (ROTARY) (OPERATION DIAL) ************************************************************ A-1193-305-A KARAOKE BOARD, COMPLETE (ZX80D: US, E2, E3, E13, E51/ZX100D: E2, E3, E51, SP, MY) A-1193-346-A KARAOKE BOARD, COMPLETE (ZX80D: MX/ZX100D: MX) ************************ < CAPACITOR > C2000 1-104-665-11 ELECT 100uF 20% 25V C2001 1-126-947-11 ELECT 47uF 20% 35V C2002 1-126-947-11 ELECT 47uF 20% 35V C2004 1-126-961-11 ELECT 2.2uF 20% 50V C2005 1-126-947-11 ELECT 47uF 20% 35V C2006 1-126-960-11 ELECT 1uF 20% 50V C2007 1-164-156-11 CERAMIC CHIP 0.1uF 25V C2008 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C2009 1-126-947-11 ELECT 47uF 20% 35V C2010 1-126-961-11 ELECT 2.2uF 20% 50V C2011 1-126-947-11 ELECT 47uF 20% 35V C2013 1-164-156-11 CERAMIC CHIP 0.1uF 25V C2015 1-164-156-11 CERAMIC CHIP 0.1uF 25V C2016 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V < DIODE > D2000 8-719-404-50 DIODE MA111-TX D2001 8-719-404-50 DIODE MA111-TX D2002 8-719-404-50 DIODE MA111-TX D2003 8-719-404-50 DIODE MA111-TX D2006 8-719-404-50 DIODE MA111-TX D2007 8-719-404-50 DIODE MA111-TX D2008 8-719-404-50 DIODE MA111-TX FUNCTION KARAOKE Ver. 1.1

IC2000 8-759-545-66 IC NJM3414AMP (TE2) IC2001 8-759-700-07 IC NJM2903M IC2002 8-759-700-07 IC NJM2903M < RESISTOR > R2000 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R2001 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R2002 1-216-837-11 METAL CHIP 22K 5% 1/10W R2004 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R2005 1-216-841-11 METAL CHIP 47K 5% 1/10W R2007 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R2008 1-216-841-11 METAL CHIP 47K 5% 1/10W R2009 1-216-821-11 METAL CHIP 1K 5% 1/10W R2010 1-216-845-11 METAL CHIP 100K 5% 1/10W R2011 1-216-864-11 SHORT CHIP 0 R2012 1-216-845-11 METAL CHIP 100K 5% 1/10W R2014 1-216-832-11 METAL CHIP 8.2K 5% 1/10W R2015 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R2016 1-216-841-11 METAL CHIP 47K 5% 1/10W R2017 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R2019 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R2020 1-216-864-11 SHORT CHIP 0 R2021 1-216-864-11 SHORT CHIP 0 R2022 1-216-833-11 METAL CHIP 10K 5% 1/10W R2024 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R2025 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R2026 1-216-864-11 SHORT CHIP 0 R2028 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R2029 1-216-837-11 METAL CHIP 22K 5% 1/10W R2030 1-216-864-11 SHORT CHIP 0 R2031 1-216-837-11 METAL CHIP 22K 5% 1/10W R2032 1-216-822-11 METAL CHIP 1.2K 5% 1/10W R2034 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R2035 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R2036 1-216-864-11 SHORT CHIP 0 R2037 1-216-864-11 SHORT CHIP 0 ************************************************************ A-1174-078-A MAIN BOARD, COMPLETE (ZX80D: E3) A-1174-169-A MAIN BOARD, COMPLETE (ZX80D: MX) A-1174-256-A MAIN BOARD, COMPLETE (ZX100D: MX) A-1174-328-A MAIN BOARD, COMPLETE (ZX100D: E3) A-1193-164-A MAIN BOARD, COMPLETE (ZX80D: E13) A-1193-167-A MAIN BOARD, COMPLETE (ZX80D: E2) A-1193-171-A MAIN BOARD, COMPLETE (ZX100D: SP, MY) A-1193-174-A MAIN BOARD, COMPLETE (ZX100D: E2) A-1193-435-A MAIN BOARD, COMPLETE (ZX80D: E51) A-1193-438-A MAIN BOARD, COMPLETE (ZX100D: E51) ********************* 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3 < CAPACITOR/RESISTOR > C101 1-104-665-11 ELECT 100uF 20% 25V C102 1-126-964-11 ELECT 10uF 20% 50V C103 1-126-964-11 ELECT 10uF 20% 50V C104 1-126-964-11 ELECT 10uF 20% 50V C105 1-126-964-11 ELECT 10uF 20% 50V C106 1-130-487-00 MYLAR 0.022uF 5% 50V C107 1-130-487-00 MYLAR 0.022uF 5% 50V C108 1-130-489-00 MYLAR 0.033uF 5% 50V C109 1-126-960-11 ELECT 1uF 20% 50V C110 1-137-150-11 FILM 0.01uF 5% 100V (ZX100D) C110 1-137-438-11 MYLAR 0.0082uF 5% 50V (ZX80D) C111 1-126-964-11 ELECT 10uF 20% 50V C112 1-136-498-11 FILM 0.12uF 5% 50V C113 1-136-171-00 FILM 0.33uF 5% 50V C114 1-126-964-11 ELECT 10uF 20% 50V C115 1-164-156-11 CERAMIC CHIP 0.1uF 25V C116 1-126-924-11 ELECT 330uF 20% 10V C130 1-126-964-11 ELECT 10uF 20% 50V C131 1-126-959-11 ELECT 0.47uF 20% 50V C150 1-126-964-11 ELECT 10uF 20% 50V C152 1-126-964-11 ELECT 10uF 20% 50V C153 1-126-964-11 ELECT 10uF 20% 50V C154 1-126-964-11 ELECT 10uF 20% 50V C155 1-126-964-11 ELECT 10uF 20% 50V C156 1-130-487-00 MYLAR 0.022uF 5% 50V C157 1-130-487-00 MYLAR 0.022uF 5% 50V C158 1-130-489-00 MYLAR 0.033uF 5% 50V C159 1-126-960-11 ELECT 1uF 20% 50V C160 1-137-150-11 FILM 0.01uF 5% 100V (ZX100D) C160 1-137-438-11 MYLAR 0.0082uF 5% 50V (ZX80D) C161 1-126-964-11 ELECT 10uF 20% 50V C162 1-136-498-11 FILM 0.12uF 5% 50V C163 1-136-171-00 FILM 0.33uF 5% 50V C164 1-126-964-11 ELECT 10uF 20% 50V C166 1-126-964-11 ELECT 10uF 20% 50V C167 1-126-964-11 ELECT 10uF 20% 50V C200 1-136-497-11 FILM 0.1uF 5% 50V C201 1-136-497-11 FILM 0.1uF 5% 50V C202 1-126-964-11 ELECT 10uF 20% 50V C203 1-136-498-11 FILM 0.12uF 5% 50V C204 1-136-171-00 FILM 0.33uF 5% 50V C205 1-104-665-11 ELECT 100uF 20% 25V C206 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C207 1-124-261-00 ELECT 10uF 20% 50V C209 1-124-261-00 ELECT 10uF 20% 50V C210 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C211 1-162-960-11 CERAMIC CHIP 220PF 10% 50V C212 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C213 1-126-964-11 ELECT 10uF 20% 50V C214 1-162-960-11 CERAMIC CHIP 220PF 10% 50V C215 1-126-964-11 ELECT 10uF 20% 50V C216 1-126-964-11 ELECT 10uF 20% 50V C217 1-126-964-11 ELECT 10uF 20% 50V C218 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C219 1-126-964-11 ELECT 10uF 20% 50V C220 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C221 1-126-960-11 ELECT 1uF 20% 50V C222 1-126-964-11 ELECT 10uF 20% 50V C223 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V KARAOKE Note: Refer to SUPPLEMENT-1 for the MAIN board of US model. Ver. 1.1

ZX100D: E2, E3, E51, SP, MY) C513 1-100-566-91 CERAMIC CHIP 0.1uF 10% 25V C514 1-126-768-11 ELECT 2200uF 20% 16V C515 1-100-566-91 CERAMIC CHIP 0.1uF 10% 25V C516 1-126-927-11 ELECT 2200uF 20% 10V C517 1-126-961-11 ELECT 2.2uF 20% 50V MAIN

* CN100 1-564-711-11 PIN, CONNECTOR (SMALL TYPE) 9P CN102 1-820-049-11 CONNECTOR (SUBWOOFER) (SYSTEM CONTROL ) (ZX100D) CN105 1-691-765-11 PLUG (MICRO CONNECTOR) 3P (ZX100D) CN402 1-785-336-11 PIN, CONNECTOR (LIGHT ANGLE) 10P CN501 1-573-845-11 CONNECTOR, BOARD TO BOARD13P * CN502 1-774-876-21 CONNECTOR, BOARD TO BOARD 8P * CN503 1-564-710-11 PIN, CONNECTOR (SMALL TYPE) 8P CN504 1-564-705-11 PIN, CONNECTOR (SMALL TYPE) 3P * CN505 1-564-708-11 PIN, CONNECTOR (SMALL TYPE) 6P CN506 1-784-731-11 CONNECTOR, FFC 9P * CN508 1-569-934-11 SOCKET, CONNECTOR 17P CN509 1-569-928-11 SOCKET, CONNECTOR 11P * CN510 1-568-449-11 HOUSING, CONNECTOR (PC BOARD) 3P CN511 1-784-735-11 CONNECTOR, FFC 13P CN512 1-779-287-11 CONNECTOR, FFC (LIF (NON-ZIF)) 19P CN513 1-573-845-11 CONNECTOR, BOARD TO BOARD 13P * CN514 1-774-876-21 CONNECTOR, BOARD TO BOARD 8P CN520 1-779-281-11 CONNECTOR, FFC (LIF (NON-ZIF)) 13P CN521 1-779-289-11 CONNECTOR, FFC (LIF (NON-ZIF)) 21P CN580 1-564-506-11 PLUG, CONNECTOR 3P CN582 1-564-506-11 PLUG, CONNECTOR 3P < DIODE > D101 6-501-193-01 DIODE 1SS355WTE-17 D102 6-501-193-01 DIODE 1SS355WTE-17 D136 8-719-069-55 DIODE UDZSTE-175.6B D325 8-719-083-60 DIODE UDZSTE-174.7B D340 6-501-193-01 DIODE 1SS355WTE-17 D341 6-501-193-01 DIODE 1SS355WTE-17 D342 6-501-193-01 DIODE 1SS355WTE-17 D401 6-501-193-01 DIODE 1SS355WTE-17 D402 6-501-193-01 DIODE 1SS355WTE-17 D403 6-501-193-01 DIODE 1SS355WTE-17 D411 6-501-193-01 DIODE 1SS355WTE-17 D412 6-501-193-01 DIODE 1SS355WTE-17 D501 6-501-193-01 DIODE 1SS355WTE-17 D502 6-501-193-01 DIODE 1SS355WTE-17 D503 6-501-193-01 DIODE 1SS355WTE-17 D504 6-501-193-01 DIODE 1SS355WTE-17 D505 6-501-193-01 DIODE 1SS355WTE-17 D506 6-501-193-01 DIODE 1SS355WTE-17 D507 6-501-193-01 DIODE 1SS355WTE-17 D510 6-501-193-01 DIODE 1SS355WTE-17 (ZX80D) D511 6-501-193-01 DIODE 1SS355WTE-17 (ZX80D) D550 6-501-193-01 DIODE 1SS355WTE-17 D551 6-501-193-01 DIODE 1SS355WTE-17 (ZX80D: E2, E3, E13, E51/ZX100D: E2, E3, E51, SP, MY) D560 8-719-500-60 DIODE D5SBA20 D561 8-719-500-60 DIODE D5SBA20 D581 8-719-978-33 DIODE DTZ-TT11-6.8B D582 8-719-069-56 DIODE UDZSTE-176.2B D583 8-719-071-54 DIODE HZU2.0BTRF D584 8-719-083-63 DIODE UDZSTE-1713B D585 6-500-522-21 DIODE 10EDB40-TB3 D586 6-500-522-21 DIODE 10EDB40-TB3 < JUMPER RESISTOR > FB204 1-216-864-11 SHORT CHIP 0 FB254 1-216-864-11 SHORT CHIP 0 FB260 1-216-864-11 SHORT CHIP 0 FB261 1-216-864-11 SHORT CHIP 0 < IC > IC101 6-703-650-11 IC M61529FP-D60G IC201 6-703-651-11 IC M61530FP-D60G IC301 6-702-130-01 IC HA12237F IC304 8-759-710-97 IC NJM4565M-D IC401 6-806-203-01 IC M30622MEP-A78FPU0 IC501 6-705-809-01 IC BD4929G-TR IC507 8-759-653-07 IC PQ09RD21J00H IC550 6-703-610-01 IC RT8H015C-T112-1 IC558 6-703-547-01 IC TA7805LS IC559 6-702-771-01 IC TA78033LS IC560 8-759-394-36 IC BA09T IC561 8-759-394-36 IC BA09T < CONNECTOR/JACK > J103 1-820-048-11 CONNECTOR (LIGHTING) (D-LIGHT SYNC OUT) J201 1-770-272-11 JACK, PIN 2P (TV/SAT AUDIO IN) J202 1-770-272-11 JACK, PIN 2P (AUDIO OUT) J203 1-770-377-31 JACK, PIN 1P (SUBWOOFER OUT) (ZX80D) MAIN