HEALTH RIDER BRS HRSY54370 Operation & User’s Manual

Attach the Lift Tube (11) to the Frame (2) with the Carriage Bolt and a 1/2Ó Nylon Jam Nut (50). 8. Attach the Platform Cover (34) and the Crossbar (18) to the Frame (2) with two 3/8Ó x 2 3/4Ó Bolts (45) and two 3/8Ó Nylon Locknuts (39). Do not tighten the Nylon Locknuts yet. 9. Attach the Platform (8) to the Frame (2) and Crossbar (18) with four 1/4Ó x 2 3/4Ó Bolts (63) and four 1/4Ó Washers (55). Tighten the Nylon Locknuts from step 8 now. 10. Attach a Press Arm (6) to one side of the Press Frame (5) with two 3/8Ó x 2 1/2Ó Bolts ( ...

Press Arms (6). Press a 1 3/4Ó Square Inner Cap (65) into the Press Arm. Repeat this step for the other Press Arm (6). 12. Identify the Right Butterfly Arm (15) and the Left Butterfly Arm (14). Note the position of the welded bracket on each Arm. Butterfly Arm identification is very important for step 13. Attach a Pulley (41) and a Cable Trap (67) to the Right Butterfly Arm (15) with a 3/8Ó x 2Ó Bolt (43) and a 3/8Ó Nylon Locknut (39) but do not fully tighten the Nylon Locknuts yet. Attach a Pulley (41) and a Cable Trap (67) to the Left ...

STRAP TO THE LOW PULLEY STATION Attach the Lat Bar (21) to the Cable (35) with a Cable Clip (38). For some exercises, the Chain (37) should be attached between the Lat Bar and the Cable with two Cable Clips. Adjust the length of the Chain between the Lat Bar and the Cable so the Lat Bar is in the correct starting position for the exercise to be performed. The Nylon Strap (66) and Row Bar (31) can be attached in the same manner. ATTACHING THE LEG LEVER TO THE LOW PULLEY STATION To use the Leg Lever (12), the seat must be attached to the front upright ...

Frame (2). Identify the Left Wheel Channel (3) and the Right Wheel Channel (4) by comparing the welded brackets on the bottom of each Wheel Channel. Slide the Left Wheel Channel (3) onto the indicated Small Wheels (40) attached to the Frame (2). Note: This will be easier to do if you lie the Frame on the floor. Slide the Right Wheel Channel (4) onto the Frame (2) in the same manner. 3. Slide the Left and Right Wheel Channels (3, 4) onto the 3/8Ó x 2 1/2Ó Carriage Bolts (60) in the Base (1). Partially tighten a 3/8Ó Nylon Locknut (39) onto ea ...

that all users of the home gym system are adequately informed of all precautions. 2. Read all instructions in this manual and in the accompanying literature before using the home gym system. 3. If you feel pain or dizziness at any time while exercising, stop immediately and begin cool- ing down. 4. Use the home gym system only on a level surface. Cover the floor or carpet beneath the home gym system for protection. 5. The home gym system is intended for use by one person at a time and designed to sup- port a maximum user weight of 250 pounds ...

that all users of the home gym system are adequately informed of all precautions. 2. Read all instructions in this manual and in the accompanying literature before using the home gym system. 3. If you feel pain or dizziness at any time while exercising, stop immediately and begin cool- ing down. 4. Use the home gym system only on a level surface. Cover the floor or carpet beneath the home gym system for protection. 5. The home gym system is intended for use by one person at a time and designed to sup- port a maximum user weight of 250 pounds ...

Attach the Lift Tube (11) to the Frame (2) with the Carriage Bolt and a 1/2Ó Nylon Jam Nut (50). 8. Attach the Platform Cover (34) and the Crossbar (18) to the Frame (2) with two 3/8Ó x 2 3/4Ó Bolts (45) and two 3/8Ó Nylon Locknuts (39). Do not tighten the Nylon Locknuts yet. 9. Attach the Platform (8) to the Frame (2) and Crossbar (18) with four 1/4Ó x 2 3/4Ó Bolts (63) and four 1/4Ó Washers (55). Tighten the Nylon Locknuts from step 8 now. 10. Attach a Press Arm (6) to one side of the Press Frame (5) with two 3/8Ó x 2 1/2Ó Bolts ( ...