HEIDENHAIN ND 287 - GUIDE Quick Reference Manual

Kurzanleitung Guide d‘initiation rapide 快速使用指南 クイックリファレンスガイド ND 287

UP Sensor UP 0 V Sensor 0 V / A+ A– B+ B– R+ R– / / / / » 11 µAPP Inside shield I1+ I1– I2+ I2– I0+ I0– / / / / EnDat / / / / / / DATA DATA CLOCK CLOCK ND 287 X32 USB (Type B; UART) 1 2 3 4 VCC + 5 V D– D+ GND X31 V.24/RS-232-C 1 2 3 4 5 6 7 8 9 / RXD TXD DTR Signal GND DSR RTS CTS /

Before Switch-On Electrical connection Line voltage 100 - 240 Vac Power frequency 50 - 60 Hz (± 2 Hz) Power consumption † 30 W Line fuse 2 x T500 mA Wiring the power connector   L: Phase (brown) N: Neutral (blue) : Grounding conductor (yellow/green) Caution: Changes to the power cable may be made only by an electrical technician. Danger of electrical shock! Do not open the unit. • The protective ground connection • must never be interrupted, not even if a network adapter is used. Danger to internal components Do not engage or disengage any • connecting elements while the unit is under power. Use only original fuses. • Connections 1 Power switch 2 Power connection with fuse 3 Ground (protective ground) X1 Encoder input for HEIDENHAIN encoder with 11-µApp, 1-Vpp or EnDat-2.2 interface X2 Optional input: Input for encoder module or analog module X26 Optional interface: Installation of Ethernet module (100BaseT) X31 RS-232-C/V.24 interface X32 USB Type B (UART) interface X41 Switching inputs/outputs Controls and Displays 1. Position display 2. Soft keys for functions 3. Message line for displaying information, error messages, and information on samples or temperature Confi rms an entry and returns to the previous screen. Deletes an entry, acknowledges an error message, or returns to the previous screen. Moves through the soft-key pages. 4. Status bar Operating mode: Actual Value (active) – Distance-To-Go (selectable by soft key) Input: X1 (active), X2, X1 + X2, X1 – X2, f(X1;X2) (selectable by soft key if a module is connected to the 2nd input) Scale factor (inactive; can be activated via Job Setup) Error compensation (inactive; can be activated via Installation Setup) Stopwatch (inactive; can be activated via Job Setup) Unit of measure: mm (active), inch, DEG, DMS or rad (selectable by soft key) Datum point 1 (active) or 2 (selectable by soft key) Soft-key page (page 1 active, 3 pages are available, use the navigation key to move through the pages) 5. Status display (greater than, within, less than the tolerance limit) active in sorting and tolerance checking mode (minimum, actual, maximum measured value, and difference between MIN and MAX) if MEAS. SERIES mode is active (selectable by soft key) Datum setting (fl ashes when a value is entered) Reference-mark evaluation (active) Initial Operation The position display unit must be set up properly during initial operation, or when an encoder is exchanged. Only this way the unit can be adapted to the encoder requirements in order to ensure that the movements are displayed correctly. Power Up 1. Connect the components. 2. Connect the ND to the network. 3. Press the power switch to switch the ND on. The initial screen appears: 4. Select the language. Press the soft key repeatedly until the proper language appears. Press the HELP soft key to call the integrated help system in your language. The help system provides support for all further entries and functions. Integrated Help System Press the HELP soft key to call the integrated help system. It provides information and assistance (in the language of your country) for the current operation in any situation. Press the LIST OF TOPICS soft key to view information on any topic. Use the PAGE UP/DOWN soft keys to scroll one page up or down, and the arrow keys to move one line up or down. Press the C key to return to the previous screen. Very important Please note For your information