Visonic KP-140 PG2 Operation & User’s Manual

User’s Guide 1. INTRODUCTION KP-140 PG2 is a wireless keypad for the PowerG family control panels. KP-140 PG2 enables the user to arm/disarm the alarm system, to initiate emergency/fire/panic alarms, to perform one of the AUX (auxiliary) functions (see Note 4 in Section 6) and to turn lighting devices on and off. The keypad comprises an RF transmitter that sends out a differently coded RF signal for each command. The KP-140 PG2 comprises a proximity reader for operation with a proximity tag. The KP-140 PG2 supports an optional partition feature. Partitioning allows you to have up to three independently controllable areas with different user codes assigned to each partition or one user code assigned to up to three partitions. A partition can be armed or disarmed regardless of the status of the other partitions within the system. Note: Partition refers to the PowerG family control panels that support the Partitioning feature. The KP-140 PG2 enables activation of the Aux (Auxiliary), fifteen home control outputs (X-10), one PGM output, Fire and Emergency functions. Each button needs to be individually defined for the AUX, PGM or X-10 functions at the corresponding points of the "DEFINE PANEL" and "DEFINE OUTPUTS" menu of the control panel (refer to the PowerMaster Installer Guide for specific details). An "on-board" tamper switch opens when the battery compartment cover is removed, and an "under-board" tamper switch opens if the unit is removed from its mounting place. The main features of the KP-140 PG2 are: • Status, alarm memory, and trouble data retrieval from the control panel • Automatic reporting of low battery voltage. • Visual indications by red/green LED. • Keypad back lighting. • Various buzzer sounds in response to specific actions. • Back tamper and battery compartment tamper • Automatic supervision messages to the control panel. • Exit/entry beeps • Long-life 4 year (with entry/exit beeps) / 5 year (without entry/exit beeps) battery life expectancy, 3 VDC lithium battery. • Wall mounting option. Communication Indications Description Definition Red LED lights shortly, then red LED lights 1 sec. and "sad" beep is heard Failure response Red LED lights shortly, then green LED lights 1 sec. and "happy" beep is heard Success response Red LED lights shortly and no buzzer sound is heard. No communication with the control panel Keypad Buzzer Sound Description Symbol Short single beep, upon pressing a button "Happy" (success) beep "Sad" (failure) beep B A C D E F G H I J K L M A. HOME H. AUX / ENROLLMENT B. AWAY I. EMERGENCY C. DISARM J. FIRE D. LIGHT K. PANIC E. PARTITION SELECTION L. Buzzer F. INSTANT M. LED G. STATUS / ESCAPE Figure 1 - External View 2. SPECIFICATIONS Frequency Band (MHz): Europe: 433, 868, USA: 915 Modulation: GFSK. Antenna: Built-in antenna Communication Protocol: PowerG Battery type: 3V, CR123A type. Caution! Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to manufacturer's instructions. Battery Life Expectancy: 4 years (with entry/exit beeps) / 5 years (without entry/exit beeps). Operating Temperature: 0°C to 49°C (32°F to 120°F) Dimensions (LxWxD): 127x70x24mm (5 x 2-3/4 x 31/32 in) Weight (including battery): 107g (3.4 oz) Color: White Compliance with Standards: Europe EN 300220-1, EN 50130-4, EN 50131-1 Grade 2 Class II, EN 50131-3, EN 301489. USA CFR 47 part 15, Canada RSS 210

2 1 A 1. Drill 2 holes in mounting surface, insert wall anchors and fasten the bracket with 2 screws. 2. Slide the keypad into the bracket. A. Magnet (activates back tamper when bracket is removed from the wall). Figure 2 - Mounting 2 1 A 1. Slide out the cover. 2. Replace the battery (verify proper polarity) and close the cover. A. Battery compartment tamper switch Figure 3 - Battery Replacement Note: If the KP-140 is mounted near the site door, the PowerG family control panel "Quick arming" function should be disabled, otherwise site security may be compromised. 4. ENROLLMENT Refer to the PowerMaster-10 Installer Guide for the device enrollment procedure. 5. MODIFY DEVICE SETTINGS This section describes how to configure the parameters of the keypad from the PowerMaster-10 control panel. To Modify the Keypad Device Settings Refer to the PowerMaster-10 Installer Guide and perform the procedure for Adding A Wireless Device (section 4.5.2), or, Modifying a Device (section 4.5.5). Then continue below to modify the device settings. 1. Here you determine whether or not the tamper alarm will be activated and if so whether it will be a wall tamper alarm or a battery tamper alarm. 2. 3. or Select between "Disabled", "Wall Only" or "Battery Only". 4. Here you determine whether or not the control panel will monitor supervision messages sent by the KP-140 PG2 device. 5. 6. or Select between "ON" and "OFF". 7. Here you determine whether or not to activate the exit – entry beeps, or, activate the exit – entry beeps when armed AWAY only. 8. 9. or Select between "ON", "OFF" and "OFF @ Home". 10. Here you select the function of the AUX button on the keypad device. Four options are offered: Not used: No functions assigned to AUX button. Stop Beeps: Pressing the AUX button will cause the control panel and the KP-140 PG2 device to mute the beeps. Skip exit delay: Pressing the AUX button will immediately stop the exit delay. BUTTON (*) TAMPERS ON „ EXIT-ENTRY Beeps ON „ SUPERVISION DEV SETTINGS Disabled „

instructions see the PowerMaster-10 Installer Guide section 4.12 CONFIGURING OUTPUT PARAMETERS). 11. 12. or Select between "Not Used", "Stop Beeps", "Skip exit delay" and "PGM". 13. When exiting "INSTALLLER MODE" menu, the PowerMaster-10 system displays the number of devices that need to be updated, as follows: "DEV UPDATING NNN". For detailed instructions on Adding Devices, Deleting Devices, Replacing Devices and Defining Defaults see the PowerMaster-10 Installer Guide. 6. OPERATION The tables in the following sections describe how to activate the various functions of the KP-140 PG2 keypad. Security Function Actions Partition Selection (when Partition is enabled) / / (1) Arming HOME [user code] Arming AWAY [user code] Disarming [user code] Quick arm / HOME (≈ 2 sec.) Quick arm / AWAY (≈ 2 sec.) Instant (perform HOME/ AWAY arming) (2) Latchkey (perform arm AWAY) (3) Duress [duress code](2580 by default) AUX Function (4) Status (5) Automation Function Actions X-10 device ON [X-10 no. 01 to 15] X-10 device OFF [X-10 no. 01 to 15] X-10 device toggle [X-10 no. 01 to 15] PGM device ON [00] PGM device OFF [00] PGM device toggle [00] X-10 or PGM device status [00 to 15] Safety Function Actions Emergency alarm (≈ 2 sec.) Fire alarm (≈ 2 sec.) Panic alarm (≈ 2 sec.) Notes 1. For arming HOME/AWAY a specific Partition, first press the Partition number and then perform the arming action. 2. For INSTANT arming function, press the HOME/AWAY button, enter the user code while the HOME/AWAY button blinks, wait for success acknowledgement (green LED lights and "happy" beep is heard), then press the INSTANT button. 3. For LATCHKEY arming function by arming AWAY / quick arm away, wait for success acknowledgement (green LED lights and "happy" beep is heard), then press the AWAY button twice. Note: Immediately after performing arming AWAY of the system, you can perform the Latchkey and Instant functions, one after the other. 4. The function of the AUX button can be configured on the control panel (see section 5.) 5. The STATUS button has two functions; pressing the returns the KP-140 PG2 to idle mode from any sequence, or, when the KP-140 PG2 is in idle mode, it displays the status of the control panel. Pressing the button, when the KP-140 PG2 is in idle mode, provides the status of the control panel and is indicated when the / / button lights steadily and the LED provides indication on the status of the control panel (see table below). If Partition is enabled, the partition no. ( / / ) lights steadily in parallel to the / / button and the LED provides indication on the status of the indicated partition no. Not used „

Description Definition LED lights green 4 sec. Ready LED lights red 4 sec. Not Ready LED lights green 2 sec. and then yellow 2 sec. Ready + Trouble / Memory (or both) LED lights red 2 sec. and then yellow 2 sec. Not Ready + Trouble / Memory (or both) 6. Pressing a non-valid code causes a long failure beep. 7. If a keying sequence is not completed within timeout, indicated when the pressed button stops blinking, the desired function will not be executed. WARRANTY Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the “Purchaser”) against defective workmanship and materials under normal use of the Product for a period of twelve (12) months from the date of shipment by the Manufacturer. This Warranty is absolutely conditional upon the Product having been properly installed, maintained and operated under conditions of normal use in accordance with the Manufacturers recommended installation and operation instructions. Products which have become defective for any other reason, according to the Manufacturers discretion, such as improper installation, failure to follow recommended installation and operational instructions, neglect, willful damage, misuse or vandalism, accidental damage, alteration or tampering, or repair by anyone other than the manufacturer, are not covered by this Warranty. The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the Product will prevent any death and/or personal injury and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate warning or protection. The Product, properly installed and maintained, only reduces the risk of such events without warning and it is not a guarantee or insurance that such events will not occur. THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. IN NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES WHATSOEVER, AS AFORESAID. THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM PURCHASER’S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION. However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under this limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive remedy against the Manufacturer. When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and warranty and he recognizes having been informed of. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these limitations may not apply under certain circumstances. The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any telecommunication or electronic equipment or any programs. The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the Manufacturer’s discretion any Product or part thereof that may prove defective. Any repair and/or replacement shall not extend the original Warranty period. The Manufacturer shall not be responsible for dismantling and/or reinstallation costs. To exercise this Warranty the Product must be returned to the Manufacturer freight pre-paid and insured. All freight and insurance costs are the responsibility of the Purchaser and are not included in this Warranty. This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to act on its behalf in the modification, variation or extension of this warranty. This warranty shall apply to the Product only. All products, accessories or attachments of others used in conjunction with the Product, including batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall not be liable for any damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise, caused by the malfunction of the Product due to products, accessories, or attachments of others, including batteries, used in conjunction with the Products. This Warranty is exclusive to the original Purchaser and is not assignable. This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty which is contrary to the Law in the state or country were the Product is supplied shall not apply. Warning! The user must follow the Manufacturer’s installation and operational instructions including testing the Product and its whole system at least once a week and to take all necessary precautions for his/her safety and the protection of his/her property. 01/08 W.E.E.E. Product Recycling Declaration For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste. Directive 2002/96/EC Waste Electrical and Electronic Equipment. The technical documentation as required by the European Conformity Assessment procedure is kept at: UNIT 6 MADINGLEY COURT CHIPPENHAM DRIVE KINGSTON MILTON KEYNES MK10 0BZ. Telephone number: 0870 7300800, Fax number: 0870 7300801 VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788 VISONIC INC. (U.S.A.): 65 WEST DUDLEY TOWN ROAD, BLOOMFIELD CT. 06002-1376. PHONE: (860) 243-0833, (800) 223-0020. FAX: (860) 242-8094 VISONIC LTD. (UK): UNIT 6 MADINGLEY COURT CHIPPENHAM DRIVE KINGSTON MILTON KEYNES MK10 0BZ. TEL: (0870) 7300800 FAX: (0870) 7300801. TEL: (0870) 7300800 FAX: (0870) 7300801 PRODUCT SUPPORT: (0870) 7300830 VISONIC GmbH (D-A-CH): KIRCHFELDSTR. 118, D-40215 DÜSSELDORF, TEL.: +49 (0)211 600696-0, FAX: +49 (0)211 600696-19 VISONIC IBERICA: ISLA DE PALMA, 32 NAVE 7, POLÍGONO INDUSTRIAL NORTE, 28700 SAN SEBASTIÁN DE LOS REYES, (MADRID), ESPAÑA. TEL (34) 91659-3120, FAX (34) 91663-8468. www.visonic-iberica.es INTERNET: www.visonic.com ©VISONIC LTD. 2010 KP-140 PG2 D 303015 (Rev 0, 12/10)