Source Technologies STm.57b Operation & User’s Manual

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION Table of Contents 1. Unpacking 2 2. Product overview 3 3. Installation & Usage 4 3-1. Control Panel Usage 4 3-2. Battery Installation 5 3-3. Battery removel 6 3-4. Battery Charging 7 3-5. Battery Charger Usage 8 3-6. Usage of Cigar Jack for charging 9 3-7. Belt clip usage 10 3-8. Roll Paper Installation 11 3-9. Leather case Usage 12 3-10. Shoulder Strap Usage 13 3-11. Self Test 14 4. Peripherals Connection 17 4-1. Bluetooth connectiontion 17 4-2. Interface Cable Connection 18 5. Printer Cleaning 19 6. Product Specification 20 6-1. Specification 20 7. CPCL Command Compatibility 22

Recharger Serial Cable Optional Standard 2. Product overview Power switch Charger Connector Cover open button Battery Paper feed button SERIAL USB Front Side

Insert the battery inside printer as shown. As the battery is not charged at the time of your purchase, charge the battery prior to using the product. (Use the battery charger and/or the optional battery holder.) Push the Open to the direction as pointed by arrow in the image. 1 2 3 Open the battery cover and push up the hook to the direction as above. Close the battery cover once you inserted the battery completely. NOTE 3-1. Control Panel Usage Button Name function Power button This button is used to turn the printer on and off. When the printer is off, press this button for approximately 2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off. Paper Feed Button Paper output can be done manually by pressing this button. Additionally, self-testing and Hexadecimal Dumping can be processed.. 1. Refer to “3-10” for self test information. 2. Refer to the service manual regarding Hexadecimal Dumping. Battery Status Lamp 1. If the Batt, LED are Lit, the battery is fully charged. 2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level. 3. If the battery is not charged at all, the printer turns off automatically. Error Lamp If the red light is turned on, it means that the paper cover is open. 3. Setting Up the Product

1. The battery can be charged only when the temperature is 0~40℃ 2. Be sure that the printer is turn off and the battery to be charged is installed. 3. Connect the charger to the printer. 4. Recharging will now be started. NOTE 1. Unless the exclusive charger is used provided by the manufacturer, the printer can be damaged, and the manufacturer is not liable for the consequential damage. 2. Before removing the battery, make sure that power is turned off. 3. Printer does not work in the status of being connected with charger only. 4. The battery should be installed to operate printer. 5. While charging, do not turn on the power. 6. Do not operate the print while charging the battery. 7. Do not connect the charger while the printer is operated. 3-3. Battery removel Push the Open into the direction indicated with the arrow in the image. Pull out the battery as shown above. 1 2 3 Push up the hook after opening the battery cover. 3-4-1 The status of lamp in charging Status charging charging complete Charging Lamp Red Green ② ① LED

3-6 Usage of Cigar Jack Charger for charging Printer Battery holder NOTE Use the Cigar Jack offered by the manufacturer. Optional Input 12 ~ 24V 8.4V 0.8 ~ 1.2A Output 3-5. Battery charger Usage 1. Please press the battery into the holder until you can hear a snapping sound. 2. Insert DC JACK ① into the end completely as the direct shown above. 3. Plug the power code to electrical outlet. 4. While charging the battery, red light turns on. Once the charge is completed, green light turns on. Check the state of code connection when error occurs blinking on red light. 3-5-1 The status of lamp in charging Status charging charging complete Charging Lamp Red Green NOTE In the case the battery is not fixed properly in the holder, the red lamp will be blinking, Then, extract and reinsert the battery. Optional ② ① LED

1 2 3 4 Open the paper cover pressing the open button. Insert a sharp tool into the paper guide hole and push it in the direction of arrow as shown above. Put the paper in the right direction after adjusting the paper guide matching the paper width. (Remove the paper core when it is used all) Pull out a short length of the paper and shut the paper cover. Press the Feed Key once to arrange the paper. 3-7. Belt clip Usage Insert the belt hook screw into the hole of the belt hook. As shown above, fasten the screw with a screw driver. 1 2

1 2 3 4 Insert the strap into the hook on the printer. Place the end of strap into the hook of shoulder strap. After pulling out the end of strap tightly, put it into the clip to be fastened. Fasten the strap in the opposite side with the sample way. Optional 3-9. Leather Case Usage 1 2 3 Open the Velcro Put the printer into the leather case following the direction shown in the image. Close the Velcro Optional

3-11. Self Test 1 2 3 NOTE Turn off the power pressing the power button for approximately 3 seconds. The printout is produced. While you are pressing the FEED button, press the power button 1. To print ASCII pattern additionally, press the Feed button once more 2. After printing ASCII pattern, the self test will be finished automatically. 3. If the Feed button is not pressed to print ASCII pattern, self test will be finished automatically after 30 seconds.

When the printer is installed initially or when you face a problem, you can run the self test and check the information about -Control Circuit, Mechanism, Print Quality, ROM Version After checking with self-test and no issues are found, you can examine other devices and software. This function is working independent of devices and software. ● Motor protection from being overheated The motor should be stopped and cooled about more than 30 seconds after continuous printing 1.5 meter This product can communicate with other devices via Bluetooth communication and cable. 1. The Printer can be connected to devices equipped with Bluetooth communication capacity (PDAs, PCs, etc.) 2. Use the Bluetooth connection function supported by the device to connect to the printer. 4-1. Bluetooth Connection NOTE Refer to the Bluetooth Manual for more details on connection.

If the interior of the printer is dusty, printing quality can lowered. In such a case, follow the instructions below to clean up the printer. NOTE 1. Make sure to turn the printer power off prior to cleaning 2. Regarding print head cleaning, as the print head sets very hot during printing, turn off the printer power and wait approximately 10 minute before commencement. 3. When cleaning the print head, take care not to touch the heated portion of the print head. The print head subject to be damaged by static electricity. 4. Take care not to allow the print head to become scratched and /or damaged in any way. 1. Use an applicator swab moistened with an alcohol solution to clean the print head and remove any dusts. 2. Once the cleaning is completed, insert paper roll into the printer few minutes later and close the printer cover. Preventing Overheating To prevent the motor from overheating, continuous driving of the printer should be 1.5 m or less in print length. Set the pause time for 30 seconds or more after driving the printer. 4-2. Interface Cable Connection 1. Connect USB or Serial cable into the cable connector on the printer. 2. Connect the interface cable into the USB or Serial port of the device (PDA, PC, etc.) NOTE Use the cable offered by the manufacturer (USB, Serial) Serial USB

storage 10 ~ 90% Printing Method Direct Thermal Printing Speed 80mm/sec Resolution 203 DPI X 203 DPI Character ALPHA NUMERIC Character, Extension Character Barcode Code 39, Code 93, UCC/EAN-128, Code 128, UPC-E, UPC-A, EAN-8, EAN-13, EAN-14, UPC and EAN 2 or 5 digit extensions, Plessey, FIM, Postnet, Interleaved 2-of-5, MSI, Codabar Emulation CPCL Driver Window CE 4.2&5.0, Window Mobile 5.0 Sensor Black-mark, Gap, cover open Paper paper type Thermal Paper width 58mm thickness 65㎕ External Diameter Max. Φ 56mm Internal Diameter 12.5mm +/-0.5mm Reliability TPH 100km Battery Continuous Printing 54min Standby for 19hours Printing length: 249.8M Communications standard Serial(RS-232C), USB, Bluetooth Class2 Battery Charger input AC100~240V, 50/6 Hz output 8.4V , 800~1400mA Battery Battery type Li-ion output 7.4V, 2200mAh Charging time 3hours 40min Size WXDXH(mm) 104 X 74 X 154 WXDXH” 4.0 X 2.9 X 6.0 6-1. Specification 6. Pritner Specification

Compatibility BARCODE ○ BARCODE-TEXT ○ Two-Dimensional Bar Codes Compatibility PDF417 (PORTABLE DATA FILE) ○ MAXICODE ○ QRCODE ● DATAMATRIX ● GS1(RSS) ● NOTE Compatible Partially Compatible Not Compatible ○ ● △ x Compatible with only commanders provided by the manufacturer. 7. CPCL Command Compatibility

Compatibility SETLP ○ SETLF ○ Moving With X and Y Coordinates ○ LMARGIN ○ SETBOLD ○ SETSP ○ Special ASCII Characters ○ SETFF ○ SET-TOF ○ SETLP-TIMEOUT ○