Philips 24PFL5555 Operation & User’s Manual

at www.philips.com/welcome EN User manual 46PFL5755/V7 42PFL5555/V7 32PFL5355/V7 24PFL5555/V7 support

EN 1 1 Notice 2 2 Important 3 5 Side controls and indicators 4 Use your TV 8 5 Use more of your TV Attention: Frequently Asked Question 3 Your TV 7 5 Switching on Switching off Automatic Channel Set-up Manual Channel Set-up Fine Tuning a Channel Channel Edit 10 Adjusting the Picture 6 FAQ 8 8 9 9 9 10 11 11 12 13 13 14 14 14 10 Adjusting the Sound Function Settings Selecting a Signal Sourc or Look over the Layout of Terminalse Geometry Settings USB Functions 7 Other Information 15 Troubleshooting 15 16 16 8 16 16 Product information Supported display resolutions Multimedia Tuner/Reception/Transm ission Remote control Power Supported TV mounts Product 16 16 17 17 5 Sockets 9 9 Intelligent Channel Set-up Setting the Sound System Remote Control Functions specification

colour pixels. Although it has effective pixels of 99.999% or more, black dots or bright points of light (red, green or blue) may appear constantly on the screen. This is a structural property of the display (within common industry standards) and is not a malfunction. Warranty No components are user serviceable. Do not open or remove covers to the inside of the product. Repairs may only be done by Philips Service Centres and official repair shops. Failure to do so shall void any warranty, stated or implied. Any operation expressly prohibited in this manual, any adjustments, or assembly procedures not recommended or authorised in this manual, shall void the warranty.

the supplied stand. Secure the stand to the TV tightly. Place the TV on a , level surface that can support the combined weight of the TV and the stand. When wall mounting the TV, use only a wall mount that can support the weight of the TV. Secure the wall mount to a wall that can support the combined weight of the TV and wall mount. PE Electronics bears that result in accident, injury or damage. Risk of injury to children! Follow these precautions to prevent the TV from toppling over and causing injury to children: Never place the TV on a surface covered by a cloth or other material that can be pulled away. Ensure that no part of the TV hangs over the edge of the surface. Never place the TV on tall furniture (such as a bookcase) without anchoring both the furniture and TV to the wall or a suitable support. Educate children about the dangers of climbing on furniture to reach the TV. Risk of overheating! Never install the TV in a space. Always leave a space of at least 4 inches or 10 cm around the TV for ventilation. Ensure curtains or other objec ts never cover the ventilation slots on the TV. Risk of damage to the TV! Before you connect the TV to the power outlet, ensure that the power voltage matches the value printed on the back of the TV. Never connect the TV to the power outlet if the voltage is different. Risk of injury, or power cord damage! Never place the TV or any objects on the power cord. To disconnect the TV power cord easily from the power outlet, ensure that you have full access to the power cord at all times. 2 Important Read and understand all instructions before you use your TV. If damage is caused by failure to follow instructions, the warranty does not apply. Safety Risk of electric shock or fire ! Never expose the TV to rain or water. Never place liquid containers, such as vases, near the TV. If liquids are spilt on or into the TV, disconnect the TV from the power outlet immediately. Contact Philips Consumer Care to have the TV checked before use. Never place the TV, remote control or . batteries near naked flames or other heat sources, including direct sunlight. To prevent the spread o f fire,keep candles or other flames away from the TV, remote control and batteries at all times. Never insert objects into the ventilation slots or other openings on the TV. When the TV is swiveled ensure that no strain is exerted on the power cord. Strain on the power cord can loosen connections and cause arcing. Never expose the remote control or batteries to rain, water or excessive heat. Avoid force coming on to power plugs. Loose power plugs can cause arcing or Risk of injury or damage to the TV ! Two people are required to lift and carry a TV that weights more than 25 kg. fire. flat confined fire Risk of electric shock or fire ! no responsibility for improper wall mounting

batteries Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When you disconnect the power cord, always pull the plug, never the cable. Disconnect the TV from the power outlet and antenna before lightning storms. During lightning storms, never touch any par t of the TV, power cord or antenna cable. Risk of hearing damage! Avoid using earphones or headphones at high volumes or for prolonged periods of time. Low temperatures If the TV is transpor ted in temperatures below 5 until the TV temperature matches room temperature before connecting the TV to the power outlet. Screen care Avoid stationary images as much as possible. Stationary images are images that remain on-screen for extended periods of time. Examples include: on-screen menus, black bars and time displays. If you must use stationar y images, reduce screen contrast and brightness to avoid screen damage. Unplug the TV before cleaning. Clean the TV and frame with a soft, damp cloth. Never use substances such as alcohol, chemicals or household cleaners on the TV. Risk of damage to the TV screen! Never touch, push, rub or strike the screen with any object. To avoid deformations and colour fading, wipe off water drops as soon as possible. C, unpack the TV and wait

Sockets Note: The location and names of the sockets on the TV may vary according to TV model, and not all sockets are available on all models. USB 1 AV 2 RCA audio + video sockets (input) or AV 2 IN adapter socket Note: AV 2 IN adapter The AV IN sockets can be used to connect a range of equipment, including video recorders, camcorders, decoders, satellite receivers, DVD players, or games consoles. The VIDEO IN2 socket provides The socket can be used to connect the attached AV adapter cable with VIDEO and AUDIO L & R IN sockets. composite video connection. L AUDIO VIDEO AV 2 IN R 1. CHANNEL UP/DOWN button Scans up/down through the channel list. In the menu system, they act like the up/down direction buttons on the remote and adjust menu controls. MENU button Brings up the main menu or press to return to the previous menu. 3 2. VOLUME UP/DOWN button Increases/decreases the volume. In the menu system, they act like the right/left direction buttons on the remote and adjust menu controls (Note: In some menus, VOLUME UP also acts like the OK button on the remote.) 5. POWER button Turns the TV on or standby. (Note: for some models, the POWER button turns the TV on or off.) Note: The location and names of the function buttons and power button on the TV may vary according to TV model. PR PR 1 2 3 4 SOURCE button Press to select signal source. or AV 2 IN adapter These sockets can be used to connect an USB device. Note: The number of USB sockets on the TV may vary according to TV model. SPDIF SPDIF socket (output) at the back Use a digital coaxial cable to connect your TV to a compatible audio receiver. or USB 2 and EN 5 3 Your TV Side controls and indicators

This socket can be used to connect a computer. VGA ANTENNA IN ANTENNA IN socket (input) This socket can be used to connect the outside aerial or cable network. Headphone socket (output) This socket can be used to connect headphones or stereo earphones. Warning: Excessive sound pressure from earphones and headphones can cause hearing loss. YPbPr component sockets (input) or CMP adapter CMP IN adapter socket input Note: The socket can be used to connect the attached CMP adapter cable with YPbPr component sockets. Y Pb/Cb Pr/Cr COMPONENT IN These YPbPr sockets can be used to connect a device that has component video sockets, such as a DVD player. The component sockets can recognize if the device you're connecting to is Y Pb Pr compatible or Y Cb Cr compatible. The component sockets provide excellent picture quality because the video is separated into three separate parts. CMP IN adapter or R L VGA/COMPONENT AUDIO IN AUDIO IN or AUDIO IN adapter sockets (input) Note: T AUDIO IN adapter and VGA/COMPONENT VGA/CMP he VGA/CMP socket can be used to connect the attached AUDIO IN adapter cable with audio L & R sockets, be used to obtain sound. VGA/CMP AUDIO IN adapter or These AUDIO IN L & R sockets can be used to connect a range of equipment, including video recorders, camcorders, satellite receivers, DVD players, or games consoles. AUDIO IN sockets (or AUDIO in adapter) are shared by VGA and YPbPr (or CMP adapter) sockets. AV 1 RCA audio + video sockets (input) or AV 1 in adapter socket Note: AV 1 IN adapter The socket can be used to connect the attached AV adapter cable with VIDEO and AUDIO L & R IN sockets. R L AUDIO VIDEO AV 1 IN or AV 1 IN adapter VIDEO R L AV OUT AUDIO/VIDEO sockets (output) or AV adapter (output) socket Note: The AV OUT adapter socket can be used to connect the attached AV adapter cable with VIDEO and AUDIO L & R OUT sockets. AUDIO AV OUT adapter or These AV out socketscan be used to connect The VIDEO OUT socket p rovides a VCR to record programs. You must leave the TV on the same channel you are recording. composite video connection. HDMI 1 HDMI1 and HDMI2 socket (input) HDMI 2 or The HDMI can be used to connect a PC with a compatible video card installed, certain DVD players or a high-definition compatible digital satellite decoder. This socket p (High-Definition Multimedia Interface) socket rovides an uncompressed digital connection that carries both video and audio data by way of an integrated mini-plug cable. HEADPHONE or The AV IN sockets can be used to connect a range of equipment, including video recorders, camcorders, decoders, satellite receivers, DVD players, or game consoles. The VIDEO IN1 socket provides composite video connection. 6 EN

Most of your television's functions are available via the menus that appear on the screen. The remote control supplied with your set can be used to navigate through the menus and to configure all the general settings. (On/Off button) Turns the TV on or off. Note: -Remote Control ( Depending on the models) and operation of remote control may be affected by bright artifical light near to the TV. TV Access the TV mode. INCR. SURR Enables Incredible Surround for stereo sources. Enables spatial mode for mono sources. TELETEXT Toggles teletext on or off. SOURCE Press to select signal source. DEMO Toggles the demonstration menu on or off. DUAL Switches Stereo and Nicam Stereo to Mono. Selects first language (Dual I) or second language (Dual II) in bilingual programmes SLEEP Sets a delay after which the TV switches off FREEZE Freezes the picture EXIT Exits the menu system. SCENEA Deletes the selected file in the playlist . Note: - TELETEXT,DEMO.SCENEA,DUAL / MENU Brings up the menu system. (up, down, left and right direction buttons) Highlights different items in the menu system and adjusts the menu controls. OK Confirms your selection. BACK A/CH Returns to a previous screen. Toggles between the current channel and the last viewed channel. INFO Displays the status information. Fast reverse button. Fast forward button. Play/Pause button. Stop button. USB Access the USB mode. + / - Increases or decreases volume. (MUTE) Reduces the TV's volume to its minimum level. Press again to restore the volume. FORMAT Selects a picture format. CH +/- Scans up or down through the current channel list. 0-9 (numeric buttons) Enters channel numbers. PICTURE SOUND Toggles through the sound modes:STEREO,MUSIC,MOVIE,NEWS Toggles through the picture preset settings:STANDARD,BRIGHT, SOFT and PERSONAL. EN 7 SLEEP / , INCR. SURR, keys depend on model. Red,Green,Blue keys depend on model be work in USB mode. and PERSONAL. USB

control before going on to following pages describing how to use the channel set-up procedure. 1. Insert two AAA batteries in the remote control. Precautions on using batteries: - Only use the battery types specified. - Make sure you use the correct polarity. - Do not mix new and used batteries. - Do not use rechargeable batteries. - - Remove the batteries from the remote control if you are not using it for a long period of time. Do not expose batteries to excessive heat such as sunshine, fire or the like, throw them in a fire, recharge them or try to open them, as this could cause them to leak or explode. 3. Connect an outside aerial to the ANTENNA IN socket at the back of the TV set. The aerial socket (75 OHM - VHF / UHF / cable) can be used for connecting an external aerial or other equipment fitted. 4. When powered on, the TV will be turned on directly or be in standby. Note: For some models, s If the power indicator lights up, the TV set is in standby mode. Press the button on the remote control or on the TV set to turn on the TV. witch the TV on by pressing the power button. 2. Connect the power cable FIRST to the television, THEN to a mains socket. (Note: If the power cable is connected to the television, please only connect the power cable to the mains socket.) Your TV set should only be connected to an AC supply. It must not be connected to a DC supply. If the plug is detached from the cable, do not, under any circumstances, connect it to a mains socket, as there is a risk of electric shock. Note: The figures are for representation only. The location of the power socket at the back of the television might differ depending on the model. Switching off To put the TV set into standby mode, press the button on the remote control or on the TV, the TV set remains powered up,but with low energy consumption. To switch off the TV set, unplug the mains socket from the mains outlet. Note: For some models, press the power button to switch off the TV set . 4 Use your TV 8 EN

Channel set-up involves selecting all the settings required to be able to search for and store all the channels you can receive. Make sure that the television is switched on and follow all the steps in turn specified hereafter. Display the menu by pressing the Menu button. Press the left or direction button to select the Channel icon and press the or down direction or OK button to display the Channel menu. Press the up or down direction button to select Channels are arranged in a pre-set order. Refer to the following sections if you want to fine tune or skip a channel, or swap two channels. right up 1. the Auto Tuning option. 2. Press the direction or OK button to start channel search. Note: Depending on the number of channels you receive, it may take several minutes for the channel search to finish. If you want to interrupt the process, press the Menu button. The channels already found will be stored. Always start tunning from channel number 1. 3. right Intelligent Channel Set-up This operation will keep all the existed channels and add newly found channels to the end of the channel list. ress the up or down direction button to select 1. Activate the Channel menu and p the Intelligent Tuning option. 2. Press the direction or OK button to start inteligent tuning. Note: If you want to interrupt the process, press the Menu button. The channels already found will be stored. right Manual Channel Set-up Follow the below procedure if you find that some channels have not been stored after the automatic set-up as well as the intelligent set-up. right left or right left or right left or right Press Menu to return or Exit to close the menu. 1. Activate the Channel menu and p the Manual Tuning option. 2. Press the direction or OK button to enter the Manual Tuning menu. 3. Select the Current Channel option and press the press the the Frequency option and press the ress the up or down direction button to select direction button to select a channel number to store the channel that will be found. 4. If necessary, press the up or down direction button to select the Band option and direction button to toggle among VHFH, UHF and VHFL. 5. Press the up or down direction button to select direction button to search manually. 6. Manual Tuning Channel Band Frequency Search 1 VHFL 49.70 MHz Fine Tuning a Channel If the picture is not clear you can fine tune the channel. 1. Activate the Channel menu and p the Fine-Tune option. 2. Press the left or right direction button for fine tuning ress the up or down direction button to select 3. Press Menu to return or Exit to close the menu. 42.25MHZ DK Channel Auto Tuning Intelligent Tuning Manual Tuning Fine-Tune Sound System Channel Edit Setting the Sound System 1. Activate the Channel menu and p the Sound System option. 2. Press the direction or OK button to display the selectable options.. 3. Press the up or down direction button to ress the up or down direction button to select . Note:Sound system for india:BG. right select an appropriate sound system: DK, BG, I and M. 4 Press Menu to return or Exit to close the menu. EN 9

Channel Edit You can use this function to skip a channel or swap two channels. 1. Activate the Channel menu and p the Channel Edit option. 2. Press the right direction or OK button to enter the Channel Edit menu. ress the up or down direction button to select Channel Edit Current Channel Target Channel. Skip Swap 1 1 Yes ? Picture Mode: use the direction or OK through the picture preset settings: Standard, Bright, Soft or , Scale: use the direction or OK through the picture size: 4:3, Full, , Wide Screen, Brightness: Contrast: : Sharpness: right right button to display the selectable options, then press the up or down direction button to scroll Personal and press OK to confirm. button to display the selectable options, then press the up or down direction button to scroll Subtitle and Nature, (Note: some options may be not selectable for certain signal sources.) and press OK to confirm. adjusts the brightness of the picture. adjusts the difference between the light and dark areas of the picture. adjusts the richness of color. adjusts the crispness of the edges in the picture. Original Saturation Note: You are recommended to use the full screen mode. Do not use the display mode with black bands on both sides of the picture (such as 4:3) for long time, otherwise the TV screen may be damaged permanently. Note: When selecting Standard, Bright, Soft, the Back Light will restore to the defaulted setting in factory. You are recommended to use the Bright mode for vivid palette. If a channel was stored twice or its reception is poor, you can simply skip it. The skipped channels can not be selected by pressing the CH +/- buttons. 1. select the Current Channel option and press the left or right Press the up or down direction button to 10 EN direction button to select the channel number to be skipped. 2. Press the up or down direction button to select direction button to select Yes. 3. the Skip option and press the left or right Press Menu to return or Exit to close the menu. Swapping Two Channels 1. select the Current Channel option and press the left or right the Target Channel option and press the left or right the SWAP option and press the left, right Press the up or down direction button to direction button to select a channel number. 2. Press the up or down direction button to select direction button to select the channel number to be swapped. 3. Press the up or down direction button to select direction or OK button to SWAP. Adjusting the Picture The menus for adjusting the picture are used to obtain the best picture setting according to your preference, the type of programme you are watching and the ambient lighting. Display the menu by pressing the Menu button. Press the left or right direction button to select the Picture icon and press the or down direction or OK button to display the Picture menu. The Picture options are as below: Back Light: up this option can be used to adjust the brightness of the backlight, depending on room lighting. Use the left or right direction button to adjust. 80 Standard Full 50 50 50 50 0 Normal Off Off BackLight Picture Mode Scale Brightness Contrast Saturation Sharpness Color Temperature Natural Light Dyanmic Contrast Tint Picture Note: Some options may not be available for certain signal sources. 5 Use more of your TV

Off Default English Auto Sound Sound Mode Balance Scene Headphone Volume Sound EQ Smart Volume Stereo 0 Off 51 DeskTop Mode Adjusting the Sound Display the menu by pressing the Menu button. Press the left or right direction button to select the Sound icon and press the or down direction or OK button to display the Sound menu. The Sound options are as below: Sound Mode: use the direction or OK through the sound preset settings: Balance: use the direction button to balance the sound between the left and right speakers. Smart Volume: turns on this option to keep the same sound level for all channels. Scene: use the direction or OK through Headphone Volume: adjusts the sound volume of the headphones. up right Stereo, Music, News, Movie and Personal. left or right right Sound EQ: adjusts the audio frequency settings. Select the Sound EQ option, then press the right direction or OK button to display the selectable options, then press the up or down direction button to scroll button to display the selectable options, then press the up or down direction button to scroll the scene preset setting: DeskTop Mode, HangUp Mode. : Color Temperature: adjusts the color temperature of the picture. use the direction or OK through . Natural Light : turns on this option to adjust the brightness of the backlight according to the content of the inputted signal automatically, so as to optimize the picture quality and decrease the power consumption. : turns on this option to adjust the contrast automatically. Tint adjusts the balance between the red and green levels. button to display the selectable options, then press the up or down direction button to scroll the color settings: Cool for a more blue palette of picture colors; Normal; and Warm for a more red palette of picture colors Dynamic Contrast right Press Menu to return or Exit to close the menu. Smart Switch Display : press the left or right direction button to select a desired setting: Switch, Display and Off. Switch: if an equipment, e.g. a DVD player, has been connected to the sockets on the TV set and turned on, e.g. AV1 sockets, the TV set will switch to that signal source automatically (AV1 for this example). : if an equipment, e.g. a DVD player, has been connected to the sockets on the TV set and turned on, e.g. AV1 sockets, the TV set will display a prompt message on the screen. You can select OK to switch to that signal source (AV1 for this example) or Exit to ignore the prompt. OFF: disables the Smart Switch function. When SMART SWITCH function is selected as Switch/ Display,then front panel Source key shall not work. Startup Setting: Sets the startup picture. You can set the captured picture as open picture. Note: For HDMI source, the smart switch function is available only when using a HDMI cable to connect the equipment which turned on.This function is only available for HDMI,AV,YPbPr,PC,and not for USB and F. Function Settings Display the menu by pressing the Menu button. Press the left or right direction button to select the Setting icon and press the up or down direction or OK button to display the Setting menu. The Setting options are as below: Note: Some options may be not available for certain signal sources. Note: Tint is available to be adjusted only when the system of the video signal is NTSC. button to enter, then press the up or down direction button to select an option and press the left or right direction button to adjust. Note: The EQ setting is adjusted, only when the Sound Mode is in Personal Mode. Press Menu to return or Exit to close the menu. Note: The User Logo1 item is only available when capturing a picture and if selecting User Logo1, the TV will automatically display the captured picture when turning on. If Off selected, the TV Will not display any open picture. EN 11 R

select your desired menu language. Note: The available languages might differ depending on the model. Color System: use the right direction or OK button to display the selectable options, then press the up or down direction button to select your desired color system and press OK to confirm. (Note: The available color system might differ depending on the model.Color system for india:PAL. ) Child Lock : Press the right or OK button to enter,then use the number buttons to input the password (The default is 0000). Then press the left or right direction button to select the limit time. To cancel the limit, select Off. And you can also change the password: select the PW Modify item and press the right direction or OK button to enter, then enter a new password twice. Note: If you forget the password, enter 0432 to override any existing codes. Time Setting: Press the up or down direction button to select the Time Setting item, then press the right direction or OK button to enter. Current Time: press the left, right, up, down direction button to set the current time. Turn on Repeat: select the times to turn on the TV at a specific time, press the left or right direction button to toggle among Off, Once and EveryDay. (Note: if Off selected, the Turn on Time, Wake Source and Wake Channel are not adjustable.) Turn on Time: press the left, right, up, down direction button to set the turn on time. Wake Source: press the left or right direction button to select the wake up signal source. Wake Channel: press the left or right direction button to select a wake up channel. (Note: Only when the wake up source is TV, this function can be available.) Turn off Repeat: select the times to turn on the TV at a specific time, use the left or right direction button to toggle among Off, Once and EveryDay. (Note: if Off selected, the Turn off Time is not adjustable.) Current Time Turn on Repeat Turn on Time Wake Source Wake Channel Turn off Repeat Turn off Time Sleep Time --:-- Off --:-- TV 1 Off --:-- Off Selecting a Signal Source or Look over the Layout of Terminals Turn off Time: press the left, right, up, down direction button to set the turn off time. Sleep Time: sets a period of time after which the TV set goes into standby mode, use the left or right direction button to set the period (240 minutes maximum). To disable this function, select Off. Restore to default: restores all the settings to defaulted settings in factory. Press Menu to return or Exit to close the menu. Note: For some models, the Motion Enhance option may be available. Motion Enhance: This function is used to cancel motion judder. Select the Motion Enhance option, then use the left or right direction button set the Motion enhance effect: Low, Middle, High and Off. Display the menu by pressing the Menu button. Press the left or right direction button to select the Source icon and press the or down direction or OK button to display the Source menu. 1. Press the up, down, left or right direction button to select your desired source. (Note: The available source might differ depending on the model.) 2. Press the OK button to confirm the selection. 1. Press the up, down, left or right direction button to select Layout and press OK to display Interface Status. 2. Press the up, down, left or right direction button to look over. 3. up Press Menu to return or Exit to close the menu. Source TV PC HDMI1 HDMI2 AV 1 AV 2 YPbPr Layout Note: You can press the SOURCE button on the remote control to switch the source. But if the SMART switch function is on, pressing the source button shall result in switching between the connected sources only . Selecting a Signal Source Look over the Layout of Terminals Setting Smart Switch Startup Setting Language Color System Child Lock Time Setting Restore to Default Off Default English Auto 12 EN

main menu by pressing the Menu button, then select the Multimedia and press the up or down direction or OK button to display the Multimedia menu. Notes: In USB disk catalog, pressing Menu can display Multimedia and you can press the up or down direction button to toggle among Movie Show, Photo Show , Music Show and Auto Play, then press the OK button to confirm. The short keys of USB include: the up, down, left, right direction buttons and OK, Freeze, Format buttons. In USB state, if no USB device connected, the USB interface will be displayed, and the Freeze and Scale button is not available. USB Functions Geometry Settings Display the menu by pressing the MENU button. Press the left or right direction button to select the Geometry icon and press the or down direction or OK button to display the Geometry menu. Auto Adjust: press the direction or OK button to adjust the picture's position, phase and clock automatically. The menu will auto exit after the adjustment is finished.. H Position (Horizontal Position): adjusts the picture's position left or right. V Position (Vertical Position): adjusts the picture's position upward or downward. AD Clock: adjusts the clock sync of the picture. Phase: adjusts the picture if there is flicker of screen letters, color misalignment, or blurring. up right Press Menu to return or Exit to close the menu. Playing Movie: 1. Select Movie Show item, then press the right or OK button to enter the USB device. 2. Press the left or right direction button to select the USB disk symbol and press the OK button to enter the selected disk. 3. Press the up, down, left or right direction button to select a movie file, then press OK to play it. 4. When playing a movie, you can press the Menu button to display the play console. For the play console, press the left or right direction button to select an icon, then press the OK button to confirm. The play console includes: 5. Select the Stop icon in play console, and press OK or press Exit or to return. Showing photo: 1. Select Photo Show item, then press the right or OK button to enter the USB device. 2. Press the left or right direction button to select the USB disk symbol and press the OK button to enter the selected disk. 3. Press the up, down, left or right direction button to select your desired picture file and press OK to show. 4. When showing pictures, you can press the Menu button to display the play console. For the play console, press the left or right direction button to select an icon, then press the OK button to confirm. The play console includes: Note: If you want to capture a picture as open picture, select the Capture icon, press OK, then select the User Logo1 and press OK, if else, select No and press OK to cancel saving. 5. Select the Stop icon in play console, and press OK or press Exit or to return. Playing Music: 1. Select Music Show item, then press the right or OK button to enter the USB device. Play/Pause, Fast Backward, Fast Forward, Last, Next, Stop, Repeat Mode, AB Repeat setting, Playlist, Info, Slow Forward, Step play, Goto Time, Scale, Brightness, Contrast, Zoom in, Zoom out and Move View(only available after Zoom in). Play/Pause, Prev, Next, Stop, Rotate Right, Rotate Left, Music(on/off), Musiclist, Zoom in, Zoom out, Move View(only available after Zoom in), Repeat Mode, Brightness, Contrast, Capture and Info. Note: This function is only available in PC mode. Geometry Auto Adjust H Position V Position AD Clock Phase 50 50 0 60 Multimedia Movie Show Photo Show Music Show Auto Play EN 13 Note: Use Virus free Pen Drive /USB.

reading or transmitting data, avoid damaging the system or the device. 3. Pay attention to the power supply of the device when you are using a mobile hard disk or a digital camera. If the power supply is not sufficient or not stable, you may encounter problems during operating or can not operate at all. In this case, please restart the device, or unplug the device and plug it again, and ensure that its power supply is normal. 4. The system supports standard USB1.1 and USB2.0 devices, such as standard U-disks, MP3 players, mobile hard disks, etc.. 5. For obtaining better audio and video quality, suggests to use the external device which accords with USB2.0 standard. 6. Connecting two USB hard disk devices -The parameters of file, such as the pixel of picture, code rate of audio and video file, sampling rate of audio file, exceed the limit of the system; simultaneously can cause to slow the speed of reading or other problems, suggests to connect two U disk or one USB hard disk and one U-disk simultaneously. 7. When playing the video with high compression ratio, these phenomenons, such as picture standstill and menu long time response, are normal. 8. For some USB device with power supply, such as large size hard disk, MP4, etc., Suggests using it with power to avoid electric power shortage. Attention: This system supports the following file formats: Picture format: Video format: , etc.. Audio format: 1. Some non-standard mobile storage device may/ may not be recognized. Please change to use the standard device. 2. JPEG BMP PNG H.264 RM/RMVB XVID MPEG4 MPEG2 MPEG1 MP3 WMA 2. Press the left or right direction button to select the USB disk symbol and press the OK button to enter the selected disk. 3. Press the up, down, left or right direction button to select your desired music file and press OK to play it. 4. When playing music, press the Menu button to display the play console. For the play console, press the left or right direction button to select an icon, then press the OK button to confirm. The play console includes: 5. Select the Stop icon in play console, and press OK or press Exit or to return. Play/Pause, Fast Backward, Fast Forward, Prev, Next, Stop, Repeat Mode, Mute, Playlist, Info and Goto Time. Note: For coding files, there are many kinds non- standard coding method, so this system can not be guaranteed to support the file formats using any coding method. Frequently Asked Questions: 1. Under the following conditions, this system cannot decode the file and the file can not play normally: -The parameters of file, such as the pixel of picture, code rate of audio and video file, sampling rate of audio file, exceed the limit of the system; -The format of file is not matched or the file is harmed. Note: The code rate this system supports does not exceed 20Mbps. 14 EN Auto Play 1. Select the Auto Play item and press right direction or OK button to enter the USB device. 2. Press the left or right direction button to select the USB disk symbol and press the OK button to Auto Play. Note: This function is only available when the pictures and music are synchronously located in the USB root catalog. 3. Press Exit to return the USB root catalog. 6 FAQ

corrected by consulting the following troubleshooting list. No picture, no sound 1. Check if the fuse or circuit breaker is working. 2. Plug another electrical device into the outlet to make sure it is working or turned on. 3. Power plug is in a bad contact with the outlet. 4. Check the signal source. No color 1. Change the color system. 2. Adjust the saturation. 3. Try another channel. Black-white program may be received. Remote control does not work 1. Change the batteries. 2. Batteries are not installed correctly. 3. Main power is not connected. No picture, normal sound 1. Adjust the brightness and contrast. 2. Broadcasting failure may happen. Normal picture, no sound 1. Press the Vol+ button to increase volume. 2. Volume is set to mute, press the mute button to restore sound. 3. Change the sound system. 4. Broadcasting failure may happen. Unorderly ripples on the picture It is usually caused by local interference, such as cars, daylight lamps and hair driers. Adjust the antenna to minimize the interference. Blank screen in VGA mode Perhaps the TV can not recognize the resolution set by the PC. Suggest to change to the best resolution or other standard resolutions of the Windows system. Snowy dots and interference If the antenna is located in the fringe area of a television signal where the signal is weak, the picture may be marred by dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the reception. 1. Adjust the position and orientation of the indoor/outdoor antenna. 2. Check the connection of antenna. 3. Fine tune the channel. 4. Try another channel. Broadcasting failure may happen. Ignition Black spots or horizontal streaks appear, or the picture flutters or drifts. This is usually caused by interference from car ignition system, neon lamps, electric drills, or other electrical appliance. Ghost Ghosts are caused by the television signal following two paths. One is the direct path, the other is reflected from tall buildings, hills, or other objects. Changing the direction or position of the antenna may improve the reception. Radio frequency interference This interference produces moving ripples or diagonal streaks, and in some case, loss of contrast in the picture. Find out and remove the radio interference source. EN 15 7 Other Information

(Only FAT 16 or FAT 32 USB storage devices are supported) Suppor ted storage file formats: Images: JPEG, BMP, PNG Audio: MP3,WMA Note Multimedia names must not exceed 128 characters. Tuner/Reception/ Transmission Antenna input: 75ohm coaxial (IEC75) TV system: PAL Video playback: PAL, NTSC Remote control Batteries: 2 x AAA Power Mains power: AC 110~240 V , 50- 60 Hz Standby power: < 1 W Ambient temperature: 5 to 40 degrees Celsius 8 Product information Product information is subject to change without notice. For detailed product information, go to www.philips.com/support. Supported display resolutions Computer formats (HDMI) Resolution - refresh rate: 640 x 480 - 60Hz, 72Hz, 75Hz 800 x 600 - 56Hz, 60Hz, 72Hz, 75Hz 1024 x 768 - 60Hz, 70Hz, 75Hz 1280 x 768 - 60Hz 1280 x 960 - 60Hz 1280 x 1024 - 60Hz, 70Hz, 75Hz Computer formats (VGA) Resolution - refresh rate: 640 x 480 - 60Hz, 72Hz, 75Hz 800 x 600 - 56Hz, 60Hz, 72Hz 1024 x 768 - 60Hz, 70Hz, 75Hz 1280 x 960 - 60Hz 1280 x 1024 - 60Hz, 70Hz, 75Hz V i d e o f o r m a t s Resolution - refresh rate: 480i - 60Hz 480p - 60Hz 576i - 50Hz 576p - 50Hz 720p - 50Hz, 60Hz 1080i - 50Hz, 60Hz 1080p - 50Hz, 60Hz file 16 EN 1360 x 768 - 60Hz 1920 x 1080 - 60Hz 1280 x 768 - 60Hz 1360 x 768 - 60Hz 1920 x 1080 - 60Hz Video: H.264, RM/RMVB, XVID, MPEG4, MPEG2

Dimension (WxHxD): 809x 550 x 52 (mm) Weight: 9.5 kg 42PFL5555/V7 Supported TV mounts To mount the TV, purchase a Philips TV mount or a VESA-compatible TV mount. To prevent damage to cables and connectors, be sure to leave a clearance of at least 2.2 inches or 5.5cm from the back of the TV. TV screen size (inches) Required pitch (mm) Required mounting bolts Product specifi cation Design and specifications are subject to change without notice. 24PFL5555/V7 Without TV stand Dimension (WxHxD): 600 x 395 x 44 (mm) Weight: 4.6 kg Without TV stand Dimension (WxHxD): 1040x 680 x 48 (mm) Weight: 14.9 kg 46PFL5755/V7 Without TV stand Dimension (WxHxD): 1127x 731 x 48 (mm) Weight: 16.3kg EN 17 24PFL5555/V7 32PFL5355/V7 42PFL5555/V7 46PFL5755/V7 200X200 4 x M6 400X400 4 x M6 4 x M4 100X100 200X100 4 x M4 72-MS48SA-EEMAB

2. To avail the Warranty please register your product with the Philips - Logon to www.Philips.com OR Contact Philips Consumer Care Centre 3. In the unlikely event of a defect developing in the TV set contact the Philips Customer Care Centre for obtaining warranty service and inform of the defect observed in the set, the type no.and serial no.of the set. 4. On your lodging a complaint, a trained technician will call on you promptly. In the event of the technician deciding that set requires attention at the service station; kindly arrange to deliver the set to the service station designated by technician for further attention. "Home calls" by the technician would however be restricted within the municipal limits of the city / town in which the set has been registered. Type no._ Serial No._ Date of Purchase_ Purchased By: Name_ Address:_ Tel. No._ Sold by: Name_ Address:_ Contact Customer Service Executive at: 1800 102 2929(Toll free No.) 1860 180 1111 (Chargable No.) RegdOffice: PE Electronics Ltd,Auto Cars Compound,Adalat Road,Aurangabad,431005. Sold by(User rubber stamp) Model no.: Serial no.: MADE IN PRC Tel. No._ _ _ 46PFL5755/V7 42PFL5555/V7 32PFL5355/V7 24PFL5555/V7

Defects are caused by improper or reckless use. Any repair work carried out by persons other than a Philips dealer or Authorised Service Center. Any modification or alteration of any nature made in the electrical circuitry of the est. This Warranty Card is not completed and signed immediately on delivery of the set by the Philips Dealer. Fading effects and/or Ghosts (Multiple Image) in picture, if any,arising due to location / signal reception. Defects due to causes beyond control like lightning, abnormal voltage, Acts of God or while in transit to purchaser's residence. This TV receiver is covered under warranty against any defect arising out of faulty or defective material or workman ship for a period of 12 months from the date of purchase. Should a defect develop in this set during the period of warranty,PE Electronics Limited undertakes to get the set repaired free of charge either. From whom the set has been purchased or through an Authorised Service Center for warranty service. However, if the Purchaser has to shift his residence to another town on account of transfer or other reasons, the warranty benefit will be available at the Authorised Service Center. The warranty is not valid in case of any of the following events: (Refer Consumer Guidelines for further details)