Philips HTS8140/05 Operation & User’s Manual

6 FR Home Cinéma DVD 53 ES Cine en casa con DVD 101 DE DVD Home Entertainment-System 149 NL DVD home theatre 197 Register your product and get support at www.philips.com/welcome

Mains plug This apparatus is fi tted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: Remove fuse cover and fuse. Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI approved type. Refi t the fuse cover. If the fi tted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fi tted in its place. If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. Note: The severed plug must be disposed off to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere. How to connect a plug The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L). As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows: Connect the blue wire to the terminal marked N or coloured black. Connect the brown wire to the terminal marked L or coloured red. Do not connect either wire to the earth terminal in the plug, marked E (or e) or coloured green (or green and yellow). Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires. Copyright in the U.K. Recording and playback of material may require consent. See Copyright Act 1956 and The Performer’s Protection Acts 1958 to 1972. 1. 2. 3. • • • • Norge Typeskilt fi nnes på apparatens underside. Observer: Nettbryteren er sekundert innkoplet. Den innebygde netdelen er derfor ikke frakoplet nettet så lenge apparatet er tilsluttet nettkontakten. For å redusere faren for brann eller elektrisk støt, skal apparatet ikke utsettes for regn eller fuktighet. Italia DICHIARAZIONE DI CONFORMITA’ Si dichiara che l’apparecchio HTS8140, HTS8150, Philips risponde alle prescrizioni dell’art. 2 comma 1 del D.M. 28 Agosto 1995 n. 548. Fatto a Eindhoven Philips Consumer Electronics Philips, Glaslaan 25616 JB Eindhoven, The Netherlands

sikkerhedsafbrydere er ude af funktion. Undgå utsættelse for stråling. Bemærk: Netafbryderen er sekundært indkoblet og ofbryder ikke strømmen fra nettet. Den indbyggede netdel er derfor tilsluttet til lysnettet så længe netstikket sidder i stikkontakten. S Klass 1 laseraparat Varning! Om apparaten används på annat sätt än i denna bruksanvisning specifi cerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1. Observera! Stömbrytaren är sekundärt kopplad och bryter inte strömmen från nätet. Den inbyggda nätdelen är därför ansluten till elnätet så länge stickproppen sitter i vägguttaget. SF Luokan 1 laserlaite Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle. Oikeus muutoksiin varataan. Laite ei saa olla alttiina tippu-ja roiskevedelle. Huom. Toiminnanvalitsin on kytketty toisiopuolelle, eikä se kytke laitetta irti sähköverkosta. Sisäänrakennettu verkko-osa on kytkettynä sähköverkkoon aina silloin, kun pistoke on pistorasiassa.

770 - 800 nm (CD) Output Power 6 mW (DVD) 7 mW (VCD/CD) Beam divergence 60 degrees • • • • Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved. DivX, DivX Ultra Certifi ed, and associated logos are trademarks of DivX, Inc. and are used under license. Offi cial DivX® Ultra Certifi ed product. Plays all versions of DivX ® video (including DivX ® 6) with enhanced playback of DivX® media fi les and the DivX® Media Format. Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/ or other countries. HDMI, and HDMI logo and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC. The USB-IF Logos are trademarks of Universal Serial Bus Implementers Forum, Inc. iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other ENERGY STAR and the ENERGY STAR mark are registered U.S. marks CLASS 1 LASER PRODUCT ‘DCDi’ is a trademark of Faroudja, a division of Genesis Microchip, Inc.

6 2 Your product 7 Features highlight 7 Product overview 8 3 Connect 11 Place the unit 11 Connect video cables 12 Connect subwoofer 14 Connect other devices 15 Mount the DVD Home Theatre unit 17 4 Get started 19 Prepare the remote control 19 Find the correct viewing channel 20 Start Ambisound setup 20 Select menu display language 22 Turn on Progressive Scan 22 Activate EasyLink control 23 Select a play source 25 5 Play 26 Play from disc 26 Play video 27 Play music 30 Play photo 31 Play from USB device 32 Play from portable media player 33 Play from iPod 33 Play from radio 35 6 Adjust sound 37 Control the volume 37 Adjust Bass/Treble 37 Select Ambisound 37 Select a preset sound effect 38 7 Adjust settings 39 General setup 39 Audio setup 41 Video setup 43 Preferences 45 8 Additional information 48 Upgrade software 48 Care 48 Specifi cations 49 9 Troubleshooting 50 10 Glossary 52

with highly quality material and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the European Directive 2002/96/EC. Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose your old products with your normal household waste. The correct disposal of your old product will help to prevent potential negative consequences for the environment and human health. Copyright notice This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorised by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision Corporation. Reverse engineering or disassembly is prohibited. 1 Important Safety and important notice Warning! Risk of fi re or electric shock! Ensure that air can circulate freely through the ventilation holes on this unit. Allow at least 5~10 cm clearance around the unit. Never expose this unit to direct sunlight, naked fl ames or heat. Never place this unit on other electrical equipment. Keep away from this unit during lightning storms. Never remove the casing of this unit. Please leave all maintenance work to qualifi ed personnel. Keep this unit away from water, moisture and liquid- fi lled objects. • • • • • • Caution! Remove batteries if they are exhausted or if the remote control is not to be used for a long time. Do not mix batteries (old and new or carbon and alkaline, etc.). Batteries contain chemical substances, they should be disposed of properly. Visible and invisible laser radiation when open. Avoid exposure to beam. Ensure that the power outlet is always within reach. If abnormal situations occur, fully disconnect power (unplug power cord from the power outlet). • • • • • This product complies with the radio interference requirements of the European Community. This product complies with the requirements of the following directives and guidelines: 2006/95/EC, 2004/108/EC.

Congratulations on your purchase, and welcome to Philips! To fully benefi t from the support that Philips offers, register your product at www.philips.com/welcome. The all-in-one SoundBar DVD Home Theatre is designed to complement your home perfectly. Enjoy the SoundBar DVD Home Theatre with state-of-the-art Ambisound surround sound and picture quality without the clutter of multiple speakers. Features highlight Video upscaling to 1080p You can now watch the DVDs in the highest picture quality available for your HDTV. This DVD Home Theatre offers full high-defi nition video playback up to 1080p resolution for an amazing viewing experience. A highly detailed picture and increased sharpness delivers a more true-to-life picture. EasyLink EasyLink uses the HDMI CEC (Consumer Electronics Control) industry standard protocol to share functionality with all HDMI CEC compliant devices over HDMI. It enables the connected devices to control each other with a single remote control. Note Philips does not guarantee 100% interoperability with all HDMI CEC devices. • Ambisound Philips Ambisound technology reproduces multi-channel surround sound with fewer speakers to give an embracing surround experience without the hassle of setting up a full range of speaker systems. USB direct and MP3 link Simply plug your USB device into the USB socket to play your MP3/WMA/JPEG/DivX fi les; or plug your portable media player to the MP3 LINK socket to enjoy the music play in superb sound quality. Sync the audio output with the video play This DVD Home Theatre provides you the feature of delaying the audio output if the video signals that go directly to the TV is slower than the audio streams. Region codes DVD movies are usually not released at the same time in all regions of the world, thus all DVD players are programmed to a specifi c region code. Countries DVD region code Europe ALL 2 Russia ALL 5

mode. Press and hold to turn off this unit and all the HDMI CEC compliant TV/ devices (for EasyLink control only). b Z (Open/Close) Open or close the disc compartment. c Source buttons DISC: switch to DISC mode. While in disc mode, access or exit disc menu. USB: switch to USB mode. RADIO: switch to FM band. AUX/DI /MP3 LINK: switch to AUX SCART, AUX1 INPUT, AUX2 INPUT, AUX3 INPUT, OPTICAL INPUT, DIGITAL INPUT or MP3 LINK that corresponds to the socket you used to connect the external device. DOCK: switch to the iPod that is connected to the docking station. d INFO Display the current status or disc information. Display photo fi les in 12 thumbnails view. e OPTIONS Access or exit Options menu (this menu provides various setting options). f u (Play/Pause) Start or pause disc play. RADIO: start auto radio installation (only available for fi rst time setup). g x (Stop) Stop disc play. RADIO: erase the current preset radio station. • • • • • • • • • • • • • • •

Switch to treble or bass mode. Then press VOL +- to set its level setting. i AUDIO SYNC Select an audio language/channel. Press and hold to access audio sync setting. Then press VOL +- to set the audio delay time. RADIO: toggle between FM stereo and mono mode. j SOUND Select a predefi ned sound effect. k REPEAT / PROGRAM Select various repeat or shuffl e modes; turns off repeat or shuffl e mode. RADIO: press this button to start manual radio preset. RADIO: press and hold this button to start automatic radio preset. l OK Confi rm an entry or selection. m Cursor buttons (v V b B) Navigate through the on-screen menu. Press left or right for fast backward or forward search. RADIO: press up or down to tune the radio frequency. RADIO: press left or right to start auto search. n BACK / TITLE Return to the previous display menu. For DVD, go to title menu. For VCD version 2.0 or SVCD with PBC turned on: return to the menu during playback. • • • • • • • • • • • • • • • • o í/ ë (Previous/Next) Skip to the previous or next title/ chapter/track. RADIO: select a preset radio station. p H (Mute) Mute or restore the volume. q VOL +- Adjust the volume level. r AMBISOUND Select different surround sound output: auto, multi-channel or stereo. s Numeric buttons Enter a preset number or item to play. t SUBTITLE • Select DVD or DivX subtitle language. u HDMI / ANGLE Select a video resolution setting for HDMI output. Press and hold to select a different viewing angle of a DVD movie. v ZOOM Zoom in or out the picture on the TV. • • • • • • • • •

(SoundBar) are operated through touch screen display. The control displays will be dimly lit after one seconds of inactivity. • a 2 Turn on this unit or turn off to standby mode. Press and hold to turn on this unit from a low power standby mode. b Display panel c AMBISOUND Select different surround sound output: auto, multi-channel or stereo. d u (Play/Pause) Start or pause disc play. RADIO: start auto radio installation (only available for fi rst time setup). e Volume control Adjust the volume level. f x (Stop) Stop disc play. RADIO: erase the current preset radio station. • • • • • • • • g SOURCE Select a play media: DISC, USB, DOCK, RADIO FM, OPTICAL INPUT, DIGITAL INPUT, AUX SCART, AUX1 INPUT, AUX2 INPUT, AUX3 INPUT or MP3 LINK. h Z (Open/Close) Open or close the disc compartment. i Disc compartment Note The following connections are located at the left side panel of the unit. • j MP3 LINK socket To connect portable audio player. k (USB) socket • To connect USB fl ash drive, USB memory reader or digital camera. Tips To change the brightness of the touch screen display, see chapter ‘Adjust settings’ - [ General Setup ] > [ Display Dim ]. • • • •

required for this DVD Home Theatre unit before it can be used. Basic connections: Place the unit Connect video cables Connect subwoofer Optional connections: Connect other devices Connect audio from TV Connect audio from cable box/ recorder/game console Connect portable media player Connect USB device Connect iPod docking station Mount the DVD Home Theatre unit Note Refer to the type plate at the rear or bottom of the product for identifi cation and supply ratings. Before you make or change any connections, ensure that all the devices are disconnected from the power outlet. • • • • • • • • • • • • Place the unit Place this unit on top of a table or mount it on the wall (see chapter ‘Mount the DVD Home Theatre unit’). Never place this unit an enclosed cabinet. Install this unit near the AC outlet where the AC power plug can be easily reached. 1 Place this DVD Home Theatre unit near to the TV. Place it at a height that is closest to the listening ear-level. 2 Position this DVD Home Theatre so that it is directly parallel to the listening area. 3 Place the subwoofer at the corner of the room or at least one metre away from the TV. Note You may purchase a separate table top stand that can support both your Philips Plasma/LCD TV and this DVD Home Theatre unit from the nearest Philips retailers. • • • • •

This section describes how to connect this DVD Home Theatre unit to your TV so to enable viewing of disc play. Select the best video connection that your TV can support. Option 1: Connect to HDMI socket (for a HDMI, DVI or HDCP-compliant TV). Option 2: Connect to scart socket (for a standard TV). Option 3: Connect to component video socket (for a standard TV or Progressive Scan TV). Note You must connect this unit directly to a TV. • • • • Before you connect 1 Pull up the catch to remove the rear cover. 2 Connect the cables to the corresponding sockets and direct the cables to the CABLE OUT point. 3 Once complete, close the rear cover. Note All the cables must be placed properly inside the rear panel in order for the rear cover to close. •

HDMI IN HDMI OUT 1 Connect a HDMI cable (supplied) from the HDMI OUT on this unit to the HDMI IN socket on your TV. Note The HDMI connector is only compatible with HDMI compliant TVs and DVI-TVs. • Tips To optimise the video output, see chapter ‘Adjust settings’ > [ Video Setup ] > [ Advance Picture ] for details. This unit is HDMI CEC compatible. It enables connected TV/device to control each other over HDMI, see chapter ‘Activate EasyLink control’ for details. Use a HDMI/DVI adaptor in case your TV has only a DVI connection. An extra audio connection is needed to complete this connection. To route the audio from your TV to this DVD Home Theatre unit, connect an audio cable from the audio input on this unit to the audio output on your TV. This type of connections provide best picture quality. • • • • • Option 2: Connect to Scart socket SCART OUT (AUX-SCART) SCART 1 Connect a scart cable (supplied) from the SCART OUT (AUX-SCART) socket on this unit to the scart input socket on your TV. Tips To listen to the audio output from your TV, press AUX/DI /MP3 LINK repeatedly until ‘AUX SCART’ is displayed on the display panel. This type of connections provide good picture quality. • •

video socket COMPONENT VIDEO OUT Pr Pb Y 1 Connect the component video cables (not supplied) from the Y PB PR sockets on this unit to the component video input sockets on your TV. If a progressive scan TV is used, you may turn on the progressive scan mode (see chapter ‘Turn on Progressive Scan’ for details). Tips The component video input socket on your TV may be labelled as Y Pb/Cb Pr/Cr or YUV. This type of connections provide good picture quality. • • • Connect subwoofer LOUDSPEAKERS TO SUBWOOFER 1 3 4 2 5 1 Unwind the subwoofer’s interconnect cable at TO MAIN UNIT. 2 Connect the white end of the interconnect cable to the LOUDSPEAKERS socket on this unit. 3 Connect the grey end of the interconnect cable to the TO SUBWOOFER socket on this unit. 4 Connect the FM antenna (supplied) to the FM75Ω socket on the subwoofer (for some models, this cable has been connected). Extend the FM antenna and fi x its ends to the wall. 5 Connect the power cord when all the required connections are done and you are ready to enjoy this DVD Home Theatre unit.

This section describes how you can route the sound from other devices to this DVD Home Theatre unit in order enjoy sound output or audio play with multi-channel surround capabilities. Connect audio from TV TV AUDIO IN (AUX1) L R 1 Connect an audio cable (not supplied) from the TV AUDIO IN (AUX1) sockets on this unit to the AUDIO OUT sockets on your TV. Note To listen to the audio output from this connection, press AUX/DI /MP3 LINK repeatedly until ‘AUX1 INPUT’ is displayed on the display panel. • Connect audio from cable box/ recorder/game console You can choose to connect to analogue or digital socket depending on the device capabilities. Connect to analogue sockets AUX 2 AUX 3 R L 1 Connect an audio cable (not supplied) from the AUDIO IN-AUX2 or AUX3 sockets on the subwoofer to the AUDIO OUT sockets on the device. Note To listen to the audio output from this connection, press AUX/DI /MP3 LINK repeatedly until ‘AUX2 INPUT’ or ‘AUX3 INPUT’ is displayed on the display panel. • TV AUDIO IN (TV 2) L R

COAXIAL DIGITAL IN OPTICAL IN OPTICAL OUT COAXIAL DIGITAL OUT 1 Connect a coaxial cable (not supplied) from the DIGITAL IN-COAXIAL socket on the subwoofer to the COAXIAL/ DIGITAL OUT socket on the device. Note To listen to the audio output from this connection, press AUX/DI /MP3 LINK repeatedly until ‘DIGITAL INPUT’ is displayed on the display panel. • or 1 Connect an optical cable (not supplied) from the OPTICAL IN socket on the subwoofer to the OPTICAL OUT socket on the device. Note To listen to the audio output from this connection, press AUX/DI /MP3 LINK repeatedly until ‘OPTICAL INPUT’ is displayed on the display panel. • Connect portable media player MP3 1 Connect a 3.5mm stereo audio cable (supplied) from the MP3 LINK socket on this unit to the phone socket on your portable media player (such as MP3 player). Note To listen to the audio output from this connection, press AUX/DI /MP3 LINK repeatedly until ‘MP3 LINK’ is displayed on the display panel. • Connect USB device 1 Connect the USB device to (USB) socket on this unit. Note This DVD Home Theatre unit can only play/view MP3, WMA/WMV, DivX (Ultra) or JPEG fi les that are stored on such devices. To listen to the audio output from this connection, press USB. • •

DOCK 1 Connect the iPod docking station to DOCK socket on this unit. 2 To view videos/photos from iPod, connect the composite video cable (supplied) from this docking station to your TV and switch to the corresponding channel on your TV. Note To listen to the audio output from this connection, press DOCK. • Mount the DVD Home Theatre unit Caution! Risk of personal injury and damage to the unit. Allow only qualifi ed persons to mount the unit. • 1 Ensure all the required cables are connected to this unit. 2 Remove the screws and detach the DVD Home Theatre stand, then close the rear cover. 3 Attach the supplied knobs to the rear of this unit. 4 Position the supplied bracket on the wall, drill the screw holes and insert the rubber wall plugs (not supplied) into the holes.

TV, leave at least 10cm (4 inches) of space between the TV and the bracket. • 5 Secure the bracket onto the wall with the screws (not supplied). 6 Hook the DVD Home Theatre unit fi rmly onto the mounted bracket. Slide the knobs through the key holes and lock into position.

Prepare the remote control 1 Push to open the battery compartment cover. 2 Insert two batteries type R03 or AAA. Match the indications (+-) inside the battery compartment. 3 Close the cover. Note If you are not going to use the remote control for a long time, remove the batteries. • Control a play source 1 Select the source you wish to control by pressing the DISC, USB, RADIO or AUX/DI/MP3 LINK or DOCK button. 2 Then select the desired function (for example í, ë). Navigate through the menu 1 Point the remote control directly at the remote sensor on this unit and select the desired function. 2 Use the following buttons on the remote control to navigate through the on-screen menus. Button Action v V Move up or down. b B Move left or right. Confi rm a selection. Enter numbers.

channel Note Before you start, remove the door stop tag on top of the disc compartment door. • 1 Press 2 to turn on the DVD Home Theatre unit. 2 Press DISC to switch to disc mode 3 Turn on the TV and switch it to the correct video-in channel. You may go to the lowest channel on your TV, then press the Channel Down button on your TVs remote control until you see the Video In channel. You may press ° button repeatedly on your TVs remote control. Usually this channel is between the lowest and highest channels and may be called FRONT, A/V IN, VIDEO, etc.. Tips Refer to your TVs user manual on how to select the correct input on your TV. • • • • Start Ambisound setup When you turn on this unit for the fi rst time, follow the instructions on the TV to complete the Ambisound setup in order to obtain the best possible surround sound effect. Note Before you start, ensure that you have made all the required connections. Complete the Ambisound setup for this unit before you insert a disc to play. • • 1 Press DISC to switch to disc mode 2 Turn on the TV and switch it to the correct video-in channel.  A welcome message is displayed. The next few steps will help you set up your Home Theater System to match your listening environment. To optimize the Ambisound surround effect for your home, please begin with this simple setup. Stop: Exit Continue Welcome To skip the Ambisound setup, press x to exit. 3 Press B to continue.  A message on the unit orientation is displayed. •

 [ Room Acoustics ] menu is displayed. Please select the type of walls that surround your room: Select Room Acoustics Back Change Soft (Curtains, open space) Hard (Concrete, wood) 5 Select the condition of the room, then press B.  [ Room Placement ] menu is displayed. Select the Sound Bar system placement position in your room: Select Room Placement Back Change Near the right wall Corner of room Near the left wall Middle of room 6 Select the DVD Home Theatre unit (SoundBar) placement in the room, then press B.  [ Height ] menu is displayed. Select the height at which your SoundBar system is placed: Select Height Back Change High (> 1.2m / 47in) Low (< 0.8m / 32in ) Default (0.8-1.2m / 32-47in) 7 Select the height of which the DVD Home Theatre unit (SoundBar) is placed, then press B.  [ Listening Position ] menu is displayed. Select the distance between your listening position and the SoundBar system: Select Listening Position Back Change Near (> 2m / 78in ) Far (< 3m / 118in) Default (2-3m / 78-118in) 8 Select the distance between the listening position and the speakers, then press B. 9 The speaker setting is complete, press B to exit. This DVD Home Theatre unit is now ready for use.

Note You can skip this setting if this unit is connected to a HDMI CEC compliant TV. It switches automatically to the same OSD menu language as per your TV setting. • 1 Press DISC. 2 Press OPTIONS.  [ General Setup ] menu is displayed. 3 Press B. 4 Press vV to select [ OSD Language ] in the menu, then press B. English Deutsch Dansk Screen Saver DivX(R) VOD Code Sleep Timer Display Dim Disc Lock OSD Language EasyLink Français Espanõl Nederlands Standby Mode General Setup Auto The language options are different depending on your country or region. It may not correspond to the illustration shown here. 5 Press vV to select a language, then press OK. Tips To set the default language for DVD audio and disc menu, see chapter ‘Adjust settings’ - [ Preferences ] for details. • • Turn on Progressive Scan If you connect this unit to TV with the component video connection (see chapter ‘Connect video cables - Option 3: Connect to component video jack’ for details), you can turn on the progressive scan output if your TV supports progressive scan. 1 Turn on the TV to the correct viewing channel for this unit. 2 Press DISC. 3 Press OPTIONS. 4 Press V to select [ Video Setup ] in the menu, then press B. RGB YUV Video Setup Picture Settings Advanced Picture TV Display TV Type Progressive Component Video Closed Caption 5 Select [ Component Video ] > [ YUV ], then press OK. On Off Picture Settings Advanced Picture TV Display TV Type Progressive Component Video Video Setup Closed Caption

OK.  A warning message is displayed. 7 To proceed, select [ OK ] in the menu and press OK.  The progressive setup is complete. Note If a blank/distorted screen is displayed, wait for 15 seconds for the auto recover. If no picture displayed, turn off the progressive scan mode as follows: 1) Press Z to open the disc compartment. 2) Press B. 3) Press SUBTITLE. • • 8 To exit the menu, press OPTIONS. 9 You can now turn on the progressive scan mode on your TV (see the TV user manual). Note There are some progressive scan TVs that are not fully compatible with this unit, resulting in an unnatural picture when playing back a DVD VIDEO disc in the progressive scan mode. In such case, turn off the progressive scan feature on this unit and your TV. • Activate EasyLink control This feature is only applicable if this unit is connected to HDMI CEC compliant TV/device. It enables all the linked devices response or react to certain commands simultaneously with one touch control. 1 Turn on the HDMI CEC operations on your TV and other connected devices. See TVs/devices manual for details. 2 You can now enjoy the EasyLink controls. One touch play [ Auto Wake-up TV ] When you press PLAY button, this unit will wake- up from standby mode and start disc play (if a video disc is found in the disc compartment) and it will also turn on your TV and switch to the correct viewing channel. One touch power off [ System Standby ] When you press and hold STANDBY button, it will turn off this unit and all the linked devices to standby. This unit also responses to standby command from other HDMI CEC devices. One touch audio input switching [ System Audio Control ] This unit is able to render the audio signals from the active source. It switches automatically to the corresponding audio input and output the sound from its speakers system. Before you can enjoy this function, you have to map the audio inputs to the connected devices. You can use any HDMI CEC TV/device remote control to adjust the volume. • •

be placed in the disc compartment before operation. Philips does not guarantee 100% interoperability with all HDMI CEC compliant devices. • • Map the audio inputs to the connected devices Note Before you start, ensure that an audio connection has been make between this unit and your TV/ devices. • 1 Press DISC. 2 Press OPTIONS.  [ General Setup ] menu is displayed. 3 Press B. 4 Select [ EasyLink ], then press B. Screen Saver DivX(R) VOD Code Sleep Timer Display Dim Disc Lock OSD Language EasyLink Standby Mode General Setup Auto Wake-up TV System Standby System Audio Control Audio Input Mapping [ Auto Wake-up TV ] and [ System Standby ] functions are turned on by default in the factory. 5 Select [ System Audio Control ] > [ On ], then press OK. 6 Select [ Audio Input Mapping ], then press OK. • 7 Select [ OK ] in the menu, then press OK to start scanning of devices.  Once complete, audio input mapping menu is displayed. Aux3 Aux2 Digital Input Aux1 Audio Input Mapping TV Recorder Other (non-HDMI) Aux-Scart 8 Select an input to map (e.g. AUX1, AUX2), then press B. 9 Select the correct device that connected to this audio input, then press OK. Repeat steps 8~9 to map other connected devices. 10 To exit the menu, press OPTIONS. •

On the main unit SOURCE AMBISOUND 1 Press SOURCE repeatedly to select: DISC > USB > DOCK > RADIO FM > OPTICAL INPUT > DIGITAL INPUT > AUX SCART > AUX1 INPUT > AUX2 INPUT > AUX3 INPUT > MP3 LINK > DISC ... On the remote control Press DISC to switch to DISC mode. Press USB to switch to USB mode. Press RADIO to switch to FM band. Press DOCK to switch to iPod mode. Press AUX/DI /MP3 LINK repeatedly to select other external devices. Display Device connected to AUX SCART SCART OUT socket. AUX1 INPUT TV AUDIO IN sockets. AUX2 INPUT AUDIO IN-AUX2 sockets. AUX3 INPUT AUDIO IN-AUX3 sockets. OPTICAL INPUT OPTICAL IN socket. DIGITAL INPUT COAXIAL DIGITAL IN socket. MP3 LINK MP3 LINK socket. • • • • •

Playable discs DVD Video Region 2 (Europe) Region 5 (Russia) • • DVD±RW (DVD Rewritable) DVD±R (DVD Recordable) DVD+R DL (DVD+R Double Layer) ReWritable CD-RW (CD-Rewritable) Recordable CD-R (CD-Recordable) Audio CD (Compact Disc Digital Audio) Video CD Formats 1.0, 1.1, 2.0 • Super Video CD Note DVDs and DVD players are designed with regional restrictions. Ensure that the DVD video you play is for the same region zone as your player (indicated on its rear). This unit can support playback of the following fi le formats: MP3/WMA/JPEG/DivX/WMV 9. About WMV 9 - this unit only supports Main Profi le (low level) and Simple Profi le. Advanced Profi le and DRM-protected video fi les are not supported. • • • Play a disc Caution! Never place any objects other than discs into the disc compartment. Never touch the disc optical lens inside the disc compartment. • • 1 Press Z to open the disc compartment. 2 Insert a disc with its label facing up. For double-sided disc, load the side to play faces up. 3 Press Z to close the disc compartment and start disc play. To view disc play, turn on the TV to the correct viewing channel for this DVD Home Theatre unit. 4 To stop disc play, press x. Tips If the password entry menu is displayed, you have to enter the 4-digit password before it can be played. Screen saver displays automatically if the disc play is stopped for about 15 minutes. To wake up from screen saver, press DISC. This unit automatically switches to standby mode if you do not press any buttons within 30 minutes after a disc has stopped playing. • • • • •

point where it was last stopped. To start playback from the beginning, press í while the message is displayed. • Control a title 1 Play a title. 2 Use the remote control to control the title. Button Action Pause/ resume play. Stop play. Jump to the next title/chapter. Return to the beginning of the current title/chapter or jump to the previous title/chapter. m M Search backward/ forward. To change search speed, press this button repeatedly. • v V Slow motion reverse/ forward play. To change play speed, press this button repeatedly. For VCD, only forward play is possible. • • Change video play 1 Play a title. 2 Use the remote control to change the video play. Button Action Change audio language. Only applicable to discs with multiple audio language or channel. • Change subtitle language. Only applicable to discs with multiple subtitle language. • Toggle through various repeat/ shuffl e play mode; or turn off repeat mode. Repeat options vary depending on the disc type. For VCDs, repeat play is only possible when the PBC mode is turned off. • • Zoom in/out. To pan through the zoomed image, press the cursor buttons. • Display current play status. You can change the video play options here without interrupting disc play. • Press and hold to view DVD play from different camera angles. Only applicable to DVDs that contain sequences recorded from different camera angles. •

1 Press DISC to access disc main menu. 2 Select a play option, then press OK. In some menus, press number buttons to input your selection. To return to the title menu during playback, press TITLE. Access VCD menu The PBC (Playback Control) for VCD is turned on by default in the factory. When you load in a VCD, the contents menu is displayed. 1 Press vV to select a play option, then press OK to start play. If PBC is off, it skips the menu and start play from the fi rst title. During playback, you can press BACK to return to the menu (if the PBC mode is on). Tips The default setting for PBC is on. To change the default setting, see chapter ‘Adjust settings’ - [ Preferences ] > [ PBC ] for details. • • • • • Sync audio output with video play If the video play is slower than the audio output (sound does not match with the pictures,) you can delay the audio output to match the video. 1 Press and hold AUDIO SYNC until ‘AUDIO SYNC XXX’ is displayed. ‘XXX’ denotes the delay time. 2 Within fi ve seconds, press VOL +- to set the delay time for audio output. Note If the volume control is not used within 5 seconds, it resumes normal volume control function. • •

1 During playback, press INFO.  The disc status menu is displayed. 2 Select the current elapsed playing time in the menu, then press OK. [ TT Time ] (title time) [ CH Time ] (chapter time) [ Disc Time ] (disc time) [ Track Time ] (track time) 3 Press the number buttons to change the time where you want to skip to, then press OK. • • • • Play DivX® video DivX video is a digital media format that retains high quality despite a high rate of compression. This unit is DivX® Certifi ed that allows you to enjoy DivX video. 1 Insert a disc or USB that contains the DivX videos. 2 Press DISC or USB.  A contents menu is displayed. 3 Select a title to play, then press u. 4 Use the remote control to control the title. Button Action Change subtitle language. Change audio language/track. Stop play. For DivX Ultra video, press this button again to display the contents menu. • Display DivX Ultra video information. Note Only those DivX videos that were rented or purchased using the DivX registration code of this unit can be played (see chapter ‘Adjust settings’ > [ General Setup ] > [ DivX(R) VOD Code ] for details). If the subtitle does not appear correctly, change the subtitle language (see chapter ‘Adjust settings’ - [ Preferences ] > [ DivX Subtitle ] for details). The subtitle can only be displayed up to an average of 45 characters. This unit can play DivX video fi les that are up to 4GB in size. • • • •

resume from the point where it was last stopped. To start playback from fi rst track, press í. • Control a track 1 Play a track. 2 Use the remote control to control the track. Button Action Pause/ resume play. Stop play. Jump to the next track. Return to the beginning of the current track or jump to the previous track. Direct input the track number. m M Search backward/ forward. To change search speed, press this button repeatedly. • Toggle through various repeat/ shuffl e play mode; or turn off repeat mode. Repeat options vary depending on the disc type. • Play MP3/WMA music MP3/WMA is a type of highly compressed audio fi le (fi les with .mp3 or .wma extensions). 1 Insert a disc or USB that contains the MP3/ WMA music. 2 Press DISC or USB.  A contents menu is displayed. 3 Select a folder, then press OK. 4 Select a track to play, then press u. To return to the main menu, press v until ‘Previous’ folder is selected, then press OK. Note For CDs recorded in multiple sessions, only the fi rst session is played. This unit does not support MP3PRO audio format. If any special characters are present in the MP3 track name (ID3) or album name, it might not be displayed correctly on the screen because these characters are not supported. Some WMA is protected by Digital Rights Management (DRM), it cannot be played on this unit. Folders/fi les exceed the supported fi le limit of this unit will not be displayed or played. • • • • • Tips To display the data disc contents without folders, see chapter ‘Adjust settings’ - [ Preferences ] > [ MP3/JPEG Nav ] for details. • •

This unit can play JPEG photos (fi les with .jpeg or .jpg extensions). 1 Insert a disc or USB that contains the JPEG photos. 2 Press DISC or USB.  For a Kodak disc, the slideshow begins automatically.  For a JPEG disc, the photo menu is displayed. 3 Select the folder/album you want to play. To preview the photos in the folder/ album, press INFO. To go to previous or next screen display, press í / ë. To select a photo, press the cursor buttons. To display the selected photo only, press OK. 4 Press u to start slideshow play. To return to the contents menu, press BACK. • • • • • Note It may require longer time to display the disc contents on the TV due to the large number of songs/photos compiled onto one disc. If the JPEG photo is not recorded with an ‘exif’ type fi le, the actual thumbnail picture will not be shown on the display. It will be replaced with a ‘blue mountain’ thumbnail picture. This unit can only display digital camera pictures according to the JPEG-EXIF format, typically used by almost all digital cameras. It cannot display Motion JPEG and pictures in formats other than JPEG, or sound clips associated with pictures. Folders/fi les exceed the supported fi le limit of this unit will not be displayed or played. • • • • Control photo play 1 Play photo slideshow. 2 Use the remote control to control the photo. Button Action b Skip to the previous photo. B Skip to the next photo. v Rotate the photo clockwise. V Rotate the photo anti- clockwise. Zoom in/ out. Play will pause while in zoom mode. • Stop play.

Play MP3/WMA music fi les and JPEG photo fi les simultaneously to create musical slideshow. The MP3/WMA and JPEG fi les must be stored on the same disc or USB device. 1 Play MP3/WMA music. 2 Navigate to the photo folder/album and press u to start slideshow play.  Slideshow begins and continues till the end of the photo folder or album.  Audio continues to play till the end of the disc. To return to the menu, press BACK. 3 To stop slideshow play, press x. 4 To stop music play, press x again. • Play from USB device This unit can only play/view MP3, WMA/WMV, DivX (Ultra) or JPEG fi les that are stored on such devices. 1 Connect a digital camera that comply with the PTP standard, USB fl ash drive, or USB memory card reader to the (USB) socket on this unit. 2 Press USB.  A contents menu is displayed. 3 Select a fi le to play, then press u. For more information, see chapters ‘Play music, Play photo, Play video’ for details. 4 To stop play, press x or remove the USB device. Tips If the device does not fi t into the USB socket, connect it through a USB extension cable. If a multiple USB card reader is used, only one of the connected USB drive contents can be accessed. If a USB HDD is used, ensure that an auxiliary power cord connected to the USB HDD for proper operations. Digital cameras that use PTP protocol or require additional programme installation when connected to a PC are not supported. • • • • •

player Simply connect your portable media player (e.g. MP3 player) to this unit to enjoy superb sound quality from your music collections. MP3 LINK 1 Connect a 3.5mm stereo audio cable (supplied) from the MP3 LINK socket on this unit to the ‘headphone’ socket on your portable media player. 2 Press AUX/DI /MP3 LINK repeatedly until ‘MP3 LINK’ is displayed. 3 Start play on your portable media player. See chapter ‘Adjust Sound’ to enhance the audio output. 4 To stop play, press STOP button on your portable media player. Note Control playback is only possible on your portable media player. Stop play on the portable media player before you switch to other play media/source. • • • Play from iPod Simply connect your iPod to the Philips universal docking station (supplied) to enjoy your iPod play through this DVD Home Theatre unit. List of supported iPod range: iPod mini iPod nano 1st gen iPod touch iPod nano 2nd gen iPod classic iPod nano 3rd gen iPod mini 2nd gen iPod 5th gen iPod with colour display Note Refer to Philips website for latest updates on supported iPod range. • Prepare the docking station If your iPod cannot be fi t into the docking station, adjust the ‘support’ as below. A B A adjustable ‘support’ B knob

docking station anti-clockwise to loosen the adjustable ‘support’. 2 Adjust the ‘support’ A until it can fi t your iPod. 3 Turn the knob clockwise to tighten it. Control iPod music DOCK 1 Connect the docking station to the DOCK socket on this unit. 2 Dock your iPod to the docking station and turn it on. 3 Press DOCK. This unit may verify certain iPod range to ensure full compatibility. 4 Start play on your iPod. To view iPod video play, connect a video cable from the docking station to your TV and turn on ‘TV ON’ setting in your iPod. • • 5 During playback, you can use the remote control to control the music play. Button Action Change the volume level. Select a predefi ned sound effect. Select an Ambisound effect. Go to the previous/ next track. m M Search backward/ forward. Pause/resume play. Switch to ‘Extended Control mode’ to enable control of your iPod play through the contents displayed on TV. Control buttons on iPod have no function in this mode. Press this button again to return to simple play mode. • • Toggle through various repeat/shuffl e play mode; or turn off repeat mode. This option is only available in ‘Extended Control mode’. • Tips While in iPod mode, the battery of your iPod will be charged. In extended play mode, control of iPod play is only possible through the contents displayed on your TV using this DVD Home Theatre’s remote control. • •

Check if the FM antenna has been connected to the subwoofer. If not, connect the supplied FM antenna to the FM 75Ω socket and fi x its ends to the wall. Tips For better FM stereo reception, connect an external FM antenna (not supplied). Position the antenna as far away as possible from your TV, VCR or other radiation source to prevent unwanted interference. • • First time tuning The fi rst time when you access ‘RADIO’ mode, follow the instructions to install the radio stations. 1 Press RADIO.  ’AUTO INSTALL ... PRESS PLAY’ is displayed. 2 Press u.  All detected radio stations are stored.  Once complete, it tunes to the fi rst preset radio station. To stop auto tuning, press x. • Note This unit can store up to a maximum of 40 radio stations. If auto installation is not activated or less than 5 radio stations are stored, ‘AUTO INSTALL’ will be displayed again the next time you turn on to radio mode. If the FM radio station transmits RDS (Radio Data System) data, the name of the radio station will be displayed. • • • Listen to radio 1 Press RADIO. 2 Use the remote control to control the radio. Button Action Select a preset radio station. m M Tune the radio frequency backward/ forward. Toggle between FM stereo and FM mono mode. Press and hold this button to delete the preset station from the preset list. The preset number for other radio stations remain unchanged •

1 Press RADIO. 2 Press and hold PROGRAM until ‘STARTING INSTALL’ is displayed.  All previously stored radio stations will be replaced. Note If no stereo signal is detected or less than 5 stations are detected during radio installation, ‘CHECK ANTENNA’ is displayed. • Search and store radio stations individually 1 Press RADIO. 2 Press m M.  The radio frequency indication starts to change until a radio station is detected. 3 Repeat step 2 until you tune to the radio station you wish to store. To fi netune the radio frequency, press vV. 4 Press PROGRAM. If no action is carried out within 20 seconds after the above step, it exits the preset mode. 5 Press í ë (or the number buttons) to select a preset number to store. 6 Press PROGRAM to confi rm. • •

Control the volume 1 Press VOL +- to increase or decrease the volume level. To mute the volume, press H. To restore the volume, press H again or press the volume button. Adjust Bass/Treble 1 Press BASS / TREBLE. 2 Press VOL +-repeatedly to set the level for low (BASS) or high (TREBLE) tone. Note If the volume control is not used within 10 seconds, it resumes normal volume control function. • • • Select Ambisound 1 Press AMBISOUND repeatedly to select a best Ambisound output that most suits the video or music you play. Options Descriptions AUTO The surround output will be selected based on the audio stream of the played content. MULTI- CHANNEL Multi-channel surround sound. STEREO Stereo sound.

1 Press SOUND repeatedly to select a sound effect that most suits the video or music you play. Video / Music / Descriptions ACTION / ROCK / Enhanced low and high range for great sounding movie effects and atmosphere. Great for action movies and rock/pop music. DRAMA / JAZZ Clear mid and high range. Recreates the atmosphere of a live club with the artist just in front of you. Good for Jazz music and watching dramas. CONCERT / CLASSIC Flat and pure sound mode. Ideal for listening to classical music and watching live concert DVDs. GAMING / PARTY Slightly enhanced low range and strong mid range ideal for party music and video gaming. SPORTS Moderate mid range and surround effects for clear vocals and the atmosphere of a live sports venue. NEWS Enhanced mid range for clear vocals/speech.

This section describes the various setting options of this unit. Symbol Options [ General Setup ] [ Audio Setup ] [ Video Setup ] [ Preferences ] General setup 1 Press OPTIONS.  [ General Setup ] menu is displayed. 2 Press B. 3 Select an option, then press OK. General Setup Screen Saver DivX(R) VOD Code Sleep Timer Display Dim Disc Lock OSD Language EasyLink Standby Mode See the explanations of the above options in the following pages. 4 Select a setting, then press OK. To return to the previous menu, press BACK. To exit the menu, press OPTIONS. • • • [ EasyLink ] This feature is only applicable if this unit is connected to HDMI CEC compliant TV/ device. It enables all the linked devices response or react to certain commands simultaneously with one touch control. Options Descriptions [ Auto Wake- up TV ] It wake-ups your TV automatically when you press PLAY to power up this unit and start disc play (if a video disc is found in the disc compartment). To disable this feature, select [ Off ]. • [ System Standby ] Respond to standby command from other HDMI CEC compliant TV/devices. To disable this feature, select [ Decline ]. • [ System Audio Control ] Enable auto switching of audio input to the active device and output the sound from its speakers system. To enable this feature, select [ On ]. Then proceed to [ Audio Input Mapping ] to scan and map all the connected devices. •

Mapping ] Map the audio input to the connected TV/ devices correctly to enable automatic switching of input source. Press OK to start scanning of devices. Select the audio input to map (e.g. AUX1, AUX2), then press B. Select the correct device that connected to this audio input, then press OK. 1. 2. 3. Note Your TV and other connected devices must be compliant with HDMI CEC. You must turn on the HDMI CEC operations on your TV/devices before you can enjoy the EasyLink controls. See your TVs/devices manual for details. Philips does not guarantee 100% interoperability with all HDMI CEC compliant devices. • • • [ Disc Lock ] Set play restriction for a specifi c discs. Before you start, place the disc in the disc compartment (maximum 40 discs can be locked). [ Lock ] – restrict access to the current disc. The next time you want to play this disc or unlock it, you need to enter the password. [ Unlock ] – all discs can be played. Tips To set or change your password, go to [ Preferences ] > [ Password ]. • • • [ Display Dim ] Change the brightness level of the display panel to suit the lighting in your room. [ 100% ] – normal brightness. [ 70% ] – medium brightness. [ 40% ] – dimmest display. [ OSD Language ] Select the default on-screen menu language. [ Screen Saver ] Turn off or on the screen saver mode. It helps to protect the TV screen from being damage due to over exposure to a static image for too long. [ On ] – set the screen saver to appear after 15 minutes of inactivity (for example, in pause or stop mode). [ Off ] – disable screen saver mode. [ Sleep Timer ] Switch to standby automatically after the preset time. [ Off ] – disable sleep mode. [ 15, 30, 45, 60 mins ] – select the count down time before it switches to standby. [ Standby Mode ] Set the standby mode. [ Normal ] – normal standby power consumption. [ Low Power ] – low standby power consumption. However, it requires longer time to power up. • • • • • • • • •

Display the DivX® registration code. Tips Enter this unit’s DivX registration code when you rent or purchase video from www.divx.com/vod. The DivX videos rented or purchased through the DivX® VOD (Video On Demand) service can be played only on the device to which it is registered. • Audio setup 1 Press OPTIONS.  [ General Setup ] menu is displayed. 2 Press V to select [ Audio Setup ], then press B. 3 Select an option, then press OK. Audio Setup Ambisound Setup HDMI Audio Night Mode 4 Select a setting, then press OK. To return to the previous menu, press BACK. To exit the menu, press OPTIONS. • •

Change the Ambisound setup. Options Descriptions [ Setup Guide ] Select this if you want to go through the complete Ambisound settings. [ Room Acoustics ] Select the type of walls that surround your room. [ Room Placement ] Select this unit placement in the room. [ Height ] Select the height at which this unit is placed. [ Listening Position ] Select the distance between your listening position and this unit. Tips See chapter ‘Get Started - Start Ambisound setup’ for detailed information. • [ HDMI Audio ] When you connect this unit and TV with HDMI cable, select the audio output setting for this connection. [ On ] – the sound is output through both your TV and this speakers system. If the audio format on the disc is not supported, it will be downmix to two- channel sound (linear-PCM). [ Off ] – disable audio output from your TV. The sound is only output through this speakers system. • • [ Night Mode ] Make loud sound level softer and soft sound level louder so that you can watch the DVD movies at a low volume, without disturbing others. [ On ] – for quiet viewing at night (DVDs only). [ Off ] – enjoy surround sound with a full dynamic range. • •

 [ General Setup ] menu is displayed. 2 Press V to select [ Video Setup ], then press B. 3 Select an option, then press OK. Video Setup Picture Settings Advanced Picture TV Display TV Type Progressive Closed Caption Component Video See the explanations of the above options in the following pages. 4 Select a setting, then press OK. To return to the previous menu, press BACK. To exit the menu, press OPTIONS. • • • [ TV Type ] Change this setting only if the video does not appear correctly. By default, this setting matches the most common setting for TVs in your country. [ PAL ] – for PAL-system TV. [ NTSC ] – for NTSC-system TV. [ Multi ] – for TV that is compatible with both PAL and NTSC. [ TV Display ] Select the screen format according to how you want the picture to appear on your TV. 4:3 LetterBox (LB) 4:3 PanScan (PS) 16:9 (Widescreen) [ 4:3 Pan Scan ] – for standard TV, a full-height screen display with the sides trimmed. [ 4:3 Letter Box ] – for standard TV, a ‘wide-screen’ display with black bars on the top and bottom. [ 16:9 Wide Screen ] – for wide-screen TV (frame ratio 16:9). [ Picture Settings ] Select a predefi ned set of picture colour settings or customise your personal setting. [ Standard ] – original colour setting. [ Bright ] – vibrant colour setting. [ Soft ] – warm colour setting. [ Personal ] – customise the colour setting. Set the level of brightness, contrast, tint and colour saturation in the menu, then press OK. • • • • • • • • • •

This is an advanced setting to optimise the video output. This option is only applicable for video connection through HDMI or Component Video with Progressive Scan output. [ DCDi ] – Turn on or off Directional Correlation Deinterlacing feature. It fi lls the missing lines to optimise video content. It is especially effective during slow motion play. Note DCDi setting is only available for progressive scan output. • [ Gamma ] – Adjust picture intensity. Positive values bring out the detail in dark scenes, while negative values emphasize contrast. [ Chroma Delay ] – Adjust the advance delay of chroma signals to produce a perfect and clear picture. [ True Life ] – Increase the contrast and colour intensity to produce a more dynamic picture. Note To adjust the above settings, select an option and press OK. Then press cursor left or right to change the value/level setting and press OK to confi rm. • • • • • [ Wide Screen Format ] – defi ne the wide screen format for disc play. Options Descriptions [ Superwide ] Centre position of the screen is stretched less than the side. This setting is only applicable if the video resolution is set to 720p or 1080i/p. [ 4:3 Pillar Box ] No stretching of the picture. Black bars are displayed on both sides of the screen. [ Off ] Picture will be displayed according to the format of the disc. Note This setting is only available if you have set the [ TV Display ] setting to [ 16:9 Wide Screen ]. • [ HDMI Video ] – select a video resolution that is compatible with your TV display capability. Options Descriptions [ Auto ] It detects and selects the best supported video resolution automatically. [ 480p, 576p, 720p, 1080i, 1080p ] Select a video resolution that best supported by your TV. See your TVs manual for details. Note If the setting is not compatible with your TV, a blank screen appears. Wait for 15 seconds for auto recover or press HDMI repeatedly until the picture appears. • • •

Turn on or off display captions. [ On ] – show the sound effects in subtitle. Only applicable to disc with Closed Caption information included and your TV supports this feature. [ Off ] – disable closed caption. [ Progressive ] If your TV can support progressive signals, you can activate the progressive scan mode of this unit. [ On ] – turn on progressive scan mode. [ Off ] – disable progressive scan mode. Note This setting is only available if you have set the [ Component ] setting to [ YUV ]. • Tips See chapter ‘Get Started - Turn on Progressive Scan’ for detailed information. • [ Component Video ] Select the video output format that matches the video connection between this unit and your TV. [ RGB ] – for scart connection. [ YUV ] – for component video connection. • • • • • • Preferences 1 Press OPTIONS.  [ General Setup ] menu is displayed. 2 Press V to select [ Preferences ], then press B. 3 Select an option, then press OK. Preferences Parental PBC Disc Menu Password DivX Subtitle Subtitle Audio MP3/JPEG Nav See the explanations of the above options in the following pages. 4 Select a setting, then press OK. To return to the previous menu, press BACK. To exit the menu, press OPTIONS. • • •

Select the default audio language for DVDs. [ Subtitle ] Select the default subtitle language for DVDs. [ Disc Menu ] Select the menu language for DVDs. Note If the language you have set is not available on the disc, the disc uses its own default language. For some DVDs, the subtitle/audio language can only be changed from the disc menu. To select the languages that are not listed in the menu, select [ Others ]. Then check the Language Code list at the back of this user manual and enter the respective 4-digit language code. • • • [ Parental ] Restrict access to DVDs that are unsuitable for your children. These types of DVDs must be recorded with ratings. To start, press OK. Select a rating level in the menu, then press OK. Press the number buttons to enter your 4-digit password. 1. 2. 3. Note Rated DVDs above the level you set in [ Parental ] require a password to be played. The ratings are country-dependent. To allow all discs to play, select ‘8’. Some DVDs have ratings printed on them but are not recorded with ratings. This function has no effect on such DVDs. • • • Tips To set or change your password, go to [ Preferences ] > [ Password ]. • [ PBC ] For VCDs/SVCDs recorded with PBC (playback control,) you can access the disc contents through an interactive menu. [ On ] – an index menu is displayed when you load a disc for play. [ Off ] – skip the menu and start play from the fi rst title. [ MP3/JPEG Nav ] Turn off or on MP3/WMA folder display when you play a media that contains MP3/ WMA fi les. [ With Menu ] – display the folders of MP3/WMA fi les. [ Without Menu ] – display all the fi les. [ Password ] Follow the instructions on the TV to set or change the password for locked discs and play restricted DVDs. Old Password New Password Confirm PWD OK Change Password Press the number buttons to enter ‘0000’ or your last set 4-digit password at [ Old Password ] fi eld. Enter the new password at [ New Password ] fi eld. Enter the new password again at [ Confi rm PWD ] fi eld. Press OK to exit the menu. 1. 2. 3. 4. Note If you forget your 4-digit password, enter ‘0000’ before you set a new password. • • • • •

Select a character set that supports the DivX subtitle. [ Standard ] English, Irish, Danish, Estonian, Finnish, French, German, Italian, Portuguese, Luxembourgish, Norwegian (Bokmål and Nynorsk), Spanish, Swedish, Turkish [ Central Europe ] Polish, Czech, Slovak, Albanian, Hungarian, Slovene, Croatian, Serbian (Latin script), Romanian [ Cyrillic ] Belarusian, Bulgarian, Ukrainian, Macedonian, Russian, Serbian Note Ensure that the subtitle fi le has the exact same fi le name as the movie fi le. If for example the fi lename of the movie is ‘Movie.avi’, then you will need to name the text fi le ‘Movie.sub’ or ‘Movie.srt’. Greek and Hebrew languages can be download from Philips website, see chapter ‘Upgrade software’. However, it overrides the Cyrillic language from the list. • • [ Version Info ] Display the software version of this unit. Tips This information is required when you want to fi nd out if a newest software version is available at the Philips website that you may download and install on this unit. • [ Default ] Reset all the settings of this unit to factory default, except for [ Disc Lock ], [ Password ] and [ Parental ] settings remain unchanged.

that this unit is compatible with the newest formats. To check the updates, compare the current software version of this unit with the latest software version available at the Philips website. 1 Press OPTIONS. Preferences Parental PBC Disc Menu Password DivX Subtitle Version Info Default MP3/JPEG Nav 2 Select [ Preferences ] > [ Version Info ], then press OK. 3 Write down the version number, then press OPTIONS to exit the menu. 4 Go to www.philips.com/support to check the latest software version available for this unit. 5 If the latest software version is higher than the software version of this unit, download it and store onto a CD-R or USB fl ash drive 6 Insert the CD-R or USB fl ash drive to this unit. 7 Press DISC or USB, then follow the instruction on the TV to confi rm upgrade operation. Note Do not remove the CD-R or USB when software upgrade is in progress. • 8 Once software upgrade is complete, this unit turns off to standby automatically. Note We recommend that you disconnect the power cord for a few seconds and connect again to reboot the system. • Care Caution! Never use solvents such as benzene, thinner, cleaners available commercially, or anti-static sprays intended for discs. • Clean discs Wipe the disc with a micro fi bre cleaning cloth from the centre to the edge in a straight line movement. Clean main unit screen Wipe the screen surface with a micro fi bre cleaning cloth.

without notice. • Accessories supplied Quick Start Guide Remote control and batteries Scart cable Composite video cable HDMI cable 3.5mm stereo audio cable Power cable Subwoofer Wall mounting bracket and 2 wall mounting knobs iPod docking station FM wire antenna Micro fi bre cleaning cloth Amplifi er Total output power (Home Theatre): 500W Frequency response: 20 Hz - 20 kHz / ±3dB Frequency response: 20 Hz - 20 kHz / ±3dB Signal-to-noise ratio: > 65 dB (CCIR) Input sensitivity AUX SCART & AUX 1: 500 mV MP3 LINK: 250 mV Disc Laser Type: Semiconductor Disc diameter: 12cm / 8cm Video decording: MPEG1/ MPEG2 / DivX / DIvX Ultra / WMV9 Video DAC: 12 bits Signal system: PAL / NTSC Video S/N: 56 dB Audio DAC: 24 bits / 192 kHz Frequency response: 4 Hz - 20 kHz (44.1 kHz) 4 Hz - 22 kHz (48 kHz) 4 Hz - 44 kHz (96 kHz) PCM: IEC 60958 Dolby Digital, DTS: IEC60958, IEC61937 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Radio Tuning range: FM 87.5-108 MHz (50 kHz) 26dB quieting sensitivity: FM 20 dBf IF rejection ratio: FM 60 dB Signal-to-noise ratio: FM 60 dB Harmonic distortion: FM 3% Frequency response: FM 180 Hz - 10 kHz /±6dB Stereo separation: FM 26 dB (1 kHz) Stereo Threshold: FM 23.5 dB USB Compatibility: Hi-Speed USB (2.0) Class support: UMS (USB Mass Storage Class), MTP (Media Transfer Protocol) iPod docking station Dimensions (WxHxD): 34.5 x 104 (mm) Weight: 163.5 g Power (Subwoofer) Power supply: 220~240 V, 50 Hz Power consumption: 120 W Standby power consumption: < 0.3 W System: Bass Refl ex System Impedance: 4 ohm Speaker drivers: 165 mm (6 1/2”) woofer Frequency response: 35 Hz - 200 Hz Dimensions (WxHxD): 322 x 425 x 322 (mm) Weight: 12.7 kg Main unit Dimensions (WxHxD): 1047 x 174 x 155 (mm) Weight: 8.9 kg Centre speaker: Speaker impedance: 4 ohm Speaker drivers: 2x 2.5” woofer + 2 x 2” Soft dome tweeter Frequency response: 200 Hz - 20 kHz Left/Right surround speakers: Speaker impedance: 6 ohm Speaker drivers: 2x 2.5” full range Frequency response: 200 Hz - 20 kHz • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

not work. Disconnect this unit from the power outlet for a few minutes, then connect again. Ensure that the interconnect cable from the subwoofer is connected to the DVD Home Theatre unit. • • Picture No picture. Refer to your TVs manual for correct video input channel selection. Change the TV channel until you see the DVD screen. Press DISC. If this happens when you turn on the progressive scan setting or change the TV type setting, you have to switch to its default mode: Press Z to open the disc compartment. Press B (for progressive scan) or b (for TV type). Press SUBTITLE. • • • 1. 2. 3. No picture on HDMI connection. Check if the HDMI cable is faulty. Replace a new HDMI cable. If this happens when you change the HDMI video resolution, press HDMI repeatedly until the picture appears. • • Warning! Risk of electric shock. Never remove the casing of this unit. • To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this unit, check the following points before requesting service. If the problem remains unsolved, register your product and get support at www.philips.com/welcome.

correct input source (for example, AUX/DI /MP3 LINK, USB) to select the device you want to play. • No sound on HDMI connection. You may not hear any sound from the HDMI output if the connected device is non-HDCP compliant or only DVI- compatible. Ensure that the [ HDMI Audio ] setting is turned on. • • No sound from TV programmes. Connect an audio cable from the AUDIO input on this unit to the AUDIO output on your TV. Then press AUX/DI /MP3 LINK repeatedly to select the corresponding audio input source. • Play DivX video fi les cannot be played. Ensure that the DivX fi le is encoded according to the ‘Home Theatre Profi le’ with the DivX encoder. Ensure that the DivX video fi le is complete. • • The aspect ratio of the screen is not aligned with the TV display setting. The aspect ratio is fi xed on the DVD. • DivX subtitle are not displayed correctly. Ensure that the subtitle fi le name is the same as the movie fi le name. Select the correct character set. Press OPTIONS. Press B, then select [ DivX Subtitle ] in the menu. Select the character set that supports the subtitle. • • 1. 2. 3. The contents of the USB fl ash drive cannot be read. The USB fl ash drive format is not compatible with this unit. Drive is formatted with different fi le system which is not supported by this unit (e.g. NTFS). Maximum size of memory supported is 160GB. • • •

of TV screens. The ratio of a standard TV is 4:3, while the ratio of a high-defi nition or wide TV is 16:9. The letter box allows you to enjoy a picture with a wider perspective on a standard 4:3 screen. DivX The DivX code is a patent-pending, MPEG-4 based video compression technology, developed by DivX Networks, Inc., that can shrink digital video to sizes small enough to be transported over the internet, while maintaining high visual quality. Dolby Digital A surround sound system developed by Dolby Laboratories containing up to six channels of digital audio (front left and right, surround left and right, centre and subwoofer). HDMI High-Defi nition Multimedia Interface (HDMI) is a high-speed digital interface that can transmit uncompressed high defi nition video and digital multichannel audio. It delivers high quality picture and sound quality, completely free from noise. HDMI is fully backward-compatible with DVI. As required by the HDMI standard, connecting to HDMI or DVI products without HDCP (High-bandwidth Digital Content Protection) will result in no Video or Audio output. HDCP High-bandwidth Digital Content Protection is a specifi cation that provides a secure transmission of digital contents between different devices (to prevent unauthorised copyright). JPEG A very common digital still picture format. A still-picture data compression system proposed by the Joint Photographic Expert Group, which features small decrease in image quality in spite of its high compression ratio. Files are recognised by their fi le extension ‘JPG or JPEG’. MP3 A fi le format with a sound data compression system. ‘MP3’ is the abbreviation of Motion Picture Experts Group 1 (or MPEG-1) Audio Layer3. By using the MP3 format, one CD-R or CD-RW can contain about 10 times more data than a regular CD. Files are recognised by their fi le extension ‘.MP3’. MPEG Motion Picture Experts Group. A collection of compression systems for digital audio and video. Progressive Scan The progressive scan displays twice the number of frames per seconds than ordinary TV system. It offers higher picture resolution and quality. WMA Windows Media™ Audio. Refers to an audio compression technology developed by Microsoft Corporation. WMA data can be encoded by using Windows Media Player version 9 or Windows Media Player for Windows XP. Files are recognised by their fi le extension ‘WMA’. WMV Windows Media Video. Refers to a video compression technology developed by Microsoft Corporation. WMV content can be encoded by using Windows Media® Encoder 9 series. Files are recognised by their fi le extension ‘WMV’.