Vivotek IP8352 Quick Installation Manual

Contact your distributor in the event of occurrence. Refer to your user's manual for the operating temperature. Power off the Network Camera as soon as smoke or unusual odors are detected. Do not touch the Network Camera during a lightning storm. Do not place the Network Camera on unsteady surfaces. Do not drop the Network Camera. Do not insert sharp or tiny objects into the Network Camera. Replacing or failing to properly install the waterproof components, e.g., cables or cable glands, will void our IP65/66/67 warranty.

Warranty Card Waterproof Connector (Optional) Alignment Sticker Wall Mount Bracket Sun Shield Wrench / RJ45 Female/Female Coupler / Double-sided Tape / Screws Power Adapter Moisture Absorber

Gb Ethernet RJ45 Plug Power Cord Socket + AC 24V + - AC 24V -

plastic anchors into the holes and secure the plate with supplied screws. 2. Feed the cables through the front opening of the wall mount bracket. (If you want to use external devices such as sensors and alarms, please refer to the assembling steps on the next page.) 3. Hang the wall mount bracket on the plate. 4. Fix the Network Camera on the wall mount bracket with two screws on both sides. 5. Secure the wall mount bracket with the supplied screws. 6. Adjust the angle of the wall mount bracket to aim at the shooting area. Hardware Installation 3 IMPORTANT: The supplied L-type hex key wrenches are exclusively designed to match each screw. In case you will need to adjust the lens later, do not discard the wrenches.

2. Remove the rubber stopper from the bottom of the Network Camera and secure the rubber (A) and screw nut (B) tightly. 3. Open the back cover of the Network Camera. 4. If you have external devices such as sensors and alarms, feed the cables through the waterproof connector (F --> E --> C --> A+B) as the illustration shown below. Then refer to the pin definition to connect them to the general I/O terminal block. Note: The recommended cable gauge is 2.0 ~ 2.8 mm. 5. Push the seal (C) into the housing (E). 6. Insert the seals (D) into the empty holes on the seal (C) to avoid moisture. 7. Secure the sealing nut (F) tightly. 8. Tighten the back cover. 9. Remove rubber (G) and feed the cables through the wall mount bracket. Components of the Waterproof Connector Seals (D) Housing (E) Sealing Nut (F) Seal (C) Screw Nut (B) Pin Definition Assembling Steps Rubber (A) (A)+(B) 2 6 (E) (C) (F) (D) (C) 4 7 (E) (F) 3 (C) 5 8 9 (F) (G)

molding at the other end is not waterproof. Measures should be taken to prevent water from leaking in through the cable-end molding, such as the use of expanding foam sealant, putties, and so on. Note that the cable gland on the camera should also be securely fastened to attain its waterproof functionality. Waterproof Not Waterproof Cable Molding

When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch. When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. POWER COLLISION LINK RECEIVE PARTITION 1 2 3 4 5 Non-PoE Switch PoE Power Injector (optional) POWER COLLISION LINK RECEIVE PARTITION 1 2 3 4 5 PoE Switch RJ45 Female/ Female Coupler RJ45 Female/ Female Coupler

2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the "Next" button to continue the program. Network Camera Model No: IP8352 Made in Taiwan This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Pat. 6,930,709 MAC:0002D1730202 RoHS 0002D1730202 00-02-D1-73-02-02 192.168.5.151 IP8352 Installation Wizard 2 IW2 Assigning an IP Address 5 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After a brief search, the main installer window will pop up. Double-click on the MAC address that matches the one printed on the camera label or the S/N number on the package box label to open a browser management session with the Network Camera.

Ready to Use 6 3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten the zoom controller. 4. Unscrew the focus controller to adjust the focus range. Upon completion, tighten the focus controller. T W ∞ N 3 4 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents.

6. Replace the moisture absorber with a new one if you open the back cover during the installation procedure. If you want to use the supplied sun shield for outdoor environments, please follow the steps below to install: 1. Tighten the supplied two screws. 2. Attach the supplied sun shield to the Network Camera and slide it to the desired position. 3. Fix the sun shield with the supplied two screws. 5 6 1 2 3 NOTE: IMPORTANT: Please tear down the aluminum foil vacuum bag and take out the moisture absorber, then attach the absorber with the supplied double-sided tape.