Hitachi 43FWX20B Operating Manual

57UWX20B 57GWX20B 51UWX20B 51GWX20B 43FWX20B OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS 2-3 FIRST TIME USE 4-17 THE REMOTE CONTROL ON-SCREEN DISPLAY USEFUL INFORMATION INDEX 57-62 32-56 18-31 Setup Locks Ch. Manager Audio Video Move SEL Sel As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

YOUR HITACHI TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI television. Please fill out your warranty card and mail it to HITACHI. This will enable HITACHI to notify you promptly in the improb- able event that a safety problem should be discovered in your product model. Follow all warnings and instructions marked on this color television. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral tri- angle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and mainte- nance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS TELEVISION TO RAIN OR MOISTURE. NOTE: • There are no user serviceable parts inside the color television. • Model and serial numbers are indicated on back side of the television. POWER SOURCE THIS TELEVISION IS DESIGNED TO OPERATE ON 120 VOLTS 60Hz, AC CURRENT. INSERT THE POWER CORD INTO A 120 VOLT 60Hz OUTLET. TO PREVENT ELECTRIC SHOCK, DO NOT USE THE COLOR TELEVISION’S (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TER- MINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NEVER CONNECT THE COLOR TELEVISION TO 50Hz, DIRECT CURRENT, OR ANYTHING OTHER THAN THE SPECIFIED VOLTAGE. CAUTION: Never remove the back cover of the television as this can expose you to very high voltages and other haz- ards. If the television does not operate properly, unplug the television and call your authorized dealer or service center. NOTE: This television receiver will display television closed captioning, ( or ), in accordance with paragraph 15.119 of the FCC rules. CAUTION: Adjust only those controls that are covered in the instructions, as improper changes or modifications not express- ly approved by HITACHI could void the user’s authority to operate the television. MODIFICATIONS: The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hitachi America, Ltd. Home Electronics Division may void the user’s authority to operate the equipment.

Follow all warnings and instructions marked on this television. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accor- dance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use the attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the man- ufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normal- ly, or has been dropped. 15. Televisions are designed to comply with the recom- mended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to over- turn resulting in product damage and/or personal injury. 16. Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer. 17. An outdoor antenna should not be located in the vicin- ity of overhead power lines or other electrical circuits. 18. If an outside antenna is connected to the receiver be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding for the mast and sup- porting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes and requirements for the ground- ing electrode. Note to the CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding sys- tem of the building, as close to the point of cable entry as practical.


  


              

  

 
        
 Do not place any objects on the top of the televi- sion which may fall or cause a child to climb to retrieve the objects. Disposal of this product may require specific instructions pertaining to your resident state. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. PREVENTION OF SCREEN BURN Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed (non- moving) patterns can cause permanent damage to television receivers. Such “SCREEN BURNS” constitute misuse and are NOT COVERED by your HITACHI Factory Warranty. PUBLIC VIEWING OF COPYRIGHTED MATERIAL Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require prior authorization from the broadcaster or owner of the video program material. Projection TV’s are heavy and can mark or damage floor surfaces (especially wood flooring) if moved improperly. Do not slide or force TV into position. Always roll TV allowing casters at bottom of unit to help steer and position the TV.

2. Two “AA” size, 1.5V batteries (For Remote Control Unit). REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT 1. Open the battery cover of the remote control by pushing the notched part of the cover with your fingers and pulling the cover off. 2. Insert two new “AA” size batteries for the remote control. When replacing old batteries, push them towards the springs and lift them out. 3. Match the batteries to the (+) and (-) marks in the battery compartment. 4. Replace the cover. BOTTOM VIEW Lift up on tab to remove back cover. Check to make sure you have the following accessories before disposing of the packing material. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace with the same or equivalent type. CAUTION: Television stand models SP-43W and SP-43WS are designed for use with a 43 inch or smaller television set. Use of a smaller stand, a non Hitachi recommended stand or a generic stand may result in instability, causing possible injury. 1 2 3 4 5 6 7 8 9 0 ANT INFO VOL CH POWER TV CBL/SAT DVD/VCR PIP SWAP PIP MODE FREEZE VIDEO PIP CH MENU MUTE EXIT LAST CH REC ASPECT VIRTUAL HD SELECT PART NAME PART NO. ILLUSTRATION CLU-4321UG REMOTE CONTROL HL01831 1. 2. 43” TELEVISION STAND SP-43W (Not included, order separately) OPTIONAL H530052 CLU-4321UG VID1 VID2 VID3 VID4 VID5 43” TELEVISION STAND SP-43WS (Not included, order separately) OPTIONAL H530053

5 CAUTION: Magnetic fields, such as those of external speakers, may cause the picture to distort if they are placed too close to the television. Move the magnetic field source away from the television until there is no picture distortion.

          
           ANTENNA Unless your TV is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient. LOCATION Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc. VIEWING The major benefit of the HITACHI Projection Television is its large viewing screen. To see this large screen at its best, test various locations in the room to find the optimum spot for viewing. The best picture is seen by sitting directly in front of the TV and about 10 to 18 feet from the screen. Picture brightness decreases as the viewer moves to the left and right of the receiver. During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the TV can be located in a different section of the room. If the TV’s audio output will be connected to a Hi-Fi system’s external speakers, the best audio performance will be obtained by placing the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For best stereo separation, place the external speakers at least four feet from the side of the TV, place the surround speakers to the side or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker placement for best performance.     
        

6 ANTENNA CONNECTIONS TO REAR JACK PANEL VHF (75-Ohm) antenna/CATV (Cable TV) When using a 75-Ohm coaxial cable system, connect the outdoor antenna or CATV coaxial cable to the ANT A (75-Ohm) terminal. If you have a second antenna or cable TV system, connect the coaxial cable to the ANT B terminal. VHF (300-Ohm) antenna/UHF antenna When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna leads to screws of the VHF or UHF adapter. Plug the adapter into the antenna terminal on the TV. When both VHF and UHF antennas are connected Attach an optional antenna cable mixer to the TV antenna terminal, and connect the cables to the antenna mixer. Consult your dealer or service store for the antenna mixer.
   

            


   
    
 
     Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output and input connector types required by the various components and the length of each cable. 300-Ohm Twin Lead Connector This outdoor antenna cable must be connected to an antenna adapter (300-Ohm to 75-Ohm). Phono Connector Used on all standard video and audio cables which con- nect to inputs and outputs located on the PC ready color television’s rear jack panel and front control panel. “F” Type 75-Ohm Coaxial Antenna Connector For connecting RF signals (antenna or cable TV) to the antenna jack on the television. S-Video (Super Video) Connector This connector is used on camcorders, VCRs and laser- disc players with an S-Video feature in place of the standard video cable to produce a high quality picture. Digital Visual Interface (DVI) Connection Cable (For UWX and GWX models only) This cable is used to connect external devices with DVI- HDTV output capability.

7 INPUT 5 S-VIDEO VIDEO -AUDIO- L/MONO R EXIT INPUT SELECT MENU MAGIC FOCUS VOL- VOL+ CH- CH+
  
     POWER PULL  Models: 51GWX20B/57GWX20B/51UWX20B/57UWX20B INPUT 3 S-VIDEO VIDEO AUDIO L/MONO R EXIT INPUT SELECT MENU MAGIC FOCUS VOL- VOL+ CH- CURSOR
  
      POWER PUSH Model: 43FWX20B CH+  MENU/SELECT button This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode.  INPUT/EXIT button Press this button to select the current antenna source, VIDEO: 1, 2, 3, 4, 5 or alternate antenna source. Your selection is shown in the top right corner of the screen. This button also serves as the EXIT button when in MENU mode.
CHANNEL selector Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as the cursor down () and up () buttons when in MENU mode.  VOLUME level Press these buttons for your desired sound level. The volume level will be displayed on the TV screen. These buttons also serve as the cursor left () and right (
) buttons when in MENU mode.  POWER button Press this button to turn the TV on or off.  MAGIC FOCUS Use this button to automatically adjust your picture quality to optimum performance (see page 36). The Magic Focus button will not work when adjustment mode is set to manual (see page 37).  FRONT INPUT JACKS (INPUT 5) Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantly view your favorite show or new recording. Press the INPUT button until VIDEO: 5 appears in the top right corner of the TV screen. If you have mono sound, insert the audio cable into the left audio jack. NOTES: Your remote control does not have an INPUT button. To change to video inputs, press VID1~VID5 buttons depending on your choice (see page 20).

8 The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples: NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture may be abnormal. 2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable. 3. If you have a mono VCR, insert the audio cable into the left audio jack of your TV. INPUT 5 S-VIDEO VIDEO -AUDIO- L/MONO R MAGIC FOCUS INPUT 5 S-VIDEO VIDEO -AUDIO- L/MONO R MAGIC FOCUS

9  Antenna Input/Output The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A input can be displayed as a main picture or sub-picture. ANT B can only be displayed as a main picture. (ANT B cannot be displayed as a sub-picture.) The antenna output labeled “TO CONVERTER” allows the ANT A connection to pass directly to a different source such as a cable box, only when ANT B is displayed as a main picture.  Audio/Video Inputs 1, 2, 3 and 4 The VID1~VID4 buttons will select each video source each time they are pressed. Use the audio and video inputs to connect external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (If you have mono sound, insert the audio cable into the left audio jack.)
MONITOR OUT These jacks provide fixed audio and video signals which are used for recording. Use the S-VIDEO Output for high quality video output.  AUDIO TO HI-FI Output These jacks provide variable audio output to a separate stereo amplifier. With this connection, the audio to the stereo can be controlled by the television’s main volume.  S-VIDEO Inputs 3 and 4 Inputs 3 and 4 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability. NOTE: You may use VIDEO or S-VIDEO inputs to connect to INPUT 3 and 4, but only one of these inputs may be used at a time. NOTE: S-VIDEO Output may be used for recording, only when the input is of S-VIDEO type. 
 PB PR  PB PR   PB PR PB PR DVI-HDTV 
    L AUDIO TO HI-FI R  ANT A TO CONVERTER ANT B L Y R (MONO)/L AUDIO TO HI-FI R S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT AUDIO AUDIO AUDIO ANT A TO CONVERTER ANT B Y R (MONO)/L S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT AUDIO AUDIO AUDIO Model: 43FWX20B Models: 51/57UWX20B 51/57GWX20B

10  Component: Y-PBPR Inputs Inputs 1 and 2 provide Y-PBPR jacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may use composite video signal for INPUT:2. NOTES: 1. Do not connect composite VIDEO and S-VIDEO to Input 3, 4 or 5 at the same time. S-VIDEO has priority over VIDEO input. 2. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PB input and the components R-Y output to the TV’s PR input. 3. Your component outputs may be labeled Y-CBCR. In this case, connect the component CB output to the TV’s PB input and the component CR output to the TV’s PR input. 4. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs. (See page 35) 5. To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPR jacks. 6. Input 2 (Y/VIDEO) can be used for composite video and component video input.  DVI-HDTV Input (Input 1) (For UWX and GWX models only) Use this DVI-HDTV Input for your external devices with DVI-HDTV output such as a Set-Top-Box, high-band DTV decoders, DVD players and D-VHS with Digital Content Protection.. NOTES: 1. Only DTV format such as 1080i, 720p, 480i and 480p are available for DVI-HDTV input. 2. The DVI-HDTV input is NOT compatible when used with a DVD player from a personal computer. 3. When connecting a Set-Top-Box with a copy-protect digital out terminal, a high definition picture can be displayed on the screen in its digital form.

11 NOTE: 1. Connect only 1 component to each input jack. 2. Follow connections that pertain to your personal entertainment system. 3. Composite video signal can be input to Input2~Input5. 4. Cables are optional except when noted as provided. PB PR PB PR Outside antenna or cable TV coaxial cable 2-Way signal splitter Stereo System Amplifier L R INPUT Laserdisc player, VCR, camcorder, etc. HDTV Set-Top Box DVD Player Cable TV Box OUTPUT INPUT VCR #1 ANT IN OUTPUT S-VIDEO V L R ANT A TO CONVERTER ANT B L Y R (MONO)/L AUDIO TO HI-FI R S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT OUTPUT Y PB/CB PR/CR L R VCR #2 V L R OUTPUT S-VIDEO V L R INPUT S-VIDEO OUTPUT Y PB PR L R AUDIO AUDIO AUDIO DVI-HDTV DIGITAL OUTPUT CAPABILITY DIGITAL OUTPUT L R OUTPUT TYPICAL FULL-FEATURE SETUP (51/57UWX20B and 51/57GWX20B MODELS)

12 NOTE: 1. Connect only 1 component to each input jack. 2. Follow connections that pertain to your personal entertainment system. 3. Composite video signal can be input to Input2~Input5. 4. Cables are optional except when noted as provided. PB PR PB PR Outside antenna or cable TV coaxial cable 2-Way signal splitter Stereo System Amplifier L R INPUT Laserdisc player, VCR, camcorder, etc. HDTV Set-Top Box DVD Player Cable TV Box OUTPUT INPUT VCR #1 ANT IN OUTPUT S-VIDEO V L R ANT A TO CONVERTER ANT B L Y R (MONO)/L AUDIO TO HI-FI R S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT OUTPUT Y PB/CB PR/CR L R VCR #2 V L R OUTPUT S-VIDEO V L R INPUT S-VIDEO OUTPUT Y PB PR L R AUDIO AUDIO AUDIO TYPICAL FULL-FEATURE SETUP (43FWX20B)

S-VIDEO connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connec- tions in place of the standard video connection if your device has this feature. If your device has only one audio output (mono sound), connect it to the left audio jack on the television. Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables. A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output (INPUT: 3 in the example on page 11 or 12). Refer to your VCR operating guide for more information on line input-output connections. You may use VIDEO or S-VIDEO inputs to connect to Input 3, Input 4 or Input 5, but only one of these may be used at a time. Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack. COMPONENT: Y-PBPR (Input 1 &2) connections are provided for high performance components, such as DVD players and set- top-boxes. Use these connections in place of the standard video connection if your device has this feature. Input 2 accepts both composite and component video signals. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PB input and the components R-Y output to the TV’s PR input. Your component outputs may be labeled Y-CBCR. In this case, connect the components CB output to the TV’s PB input and the components CR output to the TV’s PR input. You may use composite video signal for Input 2~Input 5. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs. (See page 35) To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPR jacks.

To control the audio level of an external audio amplifier with the remote control, connect the system as shown below. NOTE: 1. To prevent damage to the speaker and distorted sound, set the volume control of the audio amplifier lower and adjust the sound using the remote control of the TV set. 2. See page 41 for AUDIO Advanced Settings. REAR PANEL OF TELEVISION PB PR PB PR PB PR PB PR Stereo System Amplifier L R INPUT ANT A TO CONVERTER ANT B L Y R (MONO)/L AUDIO TO HI-FI R S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT Stereo System Amplifier L R INPUT ANT A TO CONVERTER ANT B L Y R (MONO)/L AUDIO TO HI-FI R S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT AUDIO AUDIO AUDIO AUDIO AUDIO AUDIO DVI-HDTV The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs. The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your partic- ular assortment of components and features. For best performance, video and audio cables should be made from coaxial shielded wire. Before Operating External Video Source The input mode is changed every time the VID1~VID5 button is pressed as shown below. Connect an external source to the INPUT terminal, then press the VID1~VID5 button as necessary to view the input source. (See page 22) INPUT MODE SELECTION ORDER (ANTENNA) (INPUT) Ant A YPBPR:1 VID1 VID1 ANT NOTE: When the TV is set to VIDEO and a video signal is not received from the VIDEO INPUT JACK on the back panel of the TV (i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF), the set will appear to be OFF. CONNECTING EXTERNAL VIDEO SOURCES Model: 43FWX20B Models: 51/57UWX20B 51/57GWX20B

CONNECTING A MONAURAL AUDIO SOURCE TO INPUT2~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below. 2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack. 3. Press the VID2~VID5 button to view the program from the VCR or the laserdisc player. The VIDEO label disappears automatically after approximately four seconds. 4. Press the ANT button to return to the previous channel. PB PR PB PR OUTPUT Audio Video VCR ANT A TO CONVERTER ANT B Y R (MONO)/L S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT AUDIO AUDIO AUDIO L AUDIO TO HI-FI R PB PR PB PR OUTPUT Audio Video VCR ANT A TO CONVERTER ANT B Y R (MONO)/L S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT AUDIO AUDIO AUDIO L AUDIO TO HI-FI R DVI-HDTV Model: 43FWX20B Models: 51/57UWX20B 51/57GWX20B

CONNECTING A STEREO SOURCE TO INPUT2~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below. 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4. Press the VID2~VID5 button to view the program from the VCR or laserdisc player. The VIDEO label disappears automatically after approximately four seconds. 5. Press the ANT button to return to the previous channel. NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is played back will be abnormal if the connection is loose. 2. A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output. (INPUT: 3 in example on page 11 or 12) Refer to your VCR operating guide for more information on line input-output connections. PB PR PB PR PB PR PB PR VCR OUTPUT R L V ANT A TO CONVERTER ANT B Y R (MONO)/L S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT VCR OUTPUT R L V ANT A TO CONVERTER ANT B Y R (MONO)/L S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT AUDIO AUDIO AUDIO L AUDIO TO HI-FI R AUDIO AUDIO AUDIO L AUDIO TO HI-FI R DVI-HDTV Model: 43FWX20B Models: 51/57UWX20B 51/57GWX20B

CONNECTING AN S-VIDEO SOURCE TO INPUT 3, 4 AND 5 1. Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV set below. 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4. Press the VID3~VID5 button to view the program from the VCR or laserdisc player. The VIDEO label disappears automatically after approximately four seconds. 5. Press the ANT button to return to the previous channel. NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is played back will be abnormal if the connection is loose. 2. A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output. (INPUT: 3 in example on page 11 or 12) Refer to your VCR operating guide for more information on line input-output connections. PB PR PB PR PB PR PB PR VCR OUTPUT R L V S-VIDEO ANT A TO CONVERTER ANT B Y R (MONO)/L S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT VCR OUTPUT R L V S-VIDEO ANT A TO CONVERTER ANT B Y R (MONO)/L S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT AUDIO AUDIO AUDIO L AUDIO TO HI-FI R AUDIO AUDIO AUDIO L AUDIO TO HI-FI R DVI-HDTV Model: 43FWX20B Models: 51/57UWX20B 51/57GWX20B

CONNECTING A COMPONENT SOURCE WITH DVI-HDTV CAPABILITY TO INPUT 1. 1. Connect the DVI connection cable from the output of the HDTV set top box or DVD player to the DVI-HDTV input as shown on the TV set at right. 2. Connect the cable from the AUDIO OUT R of the HDTV set top box or DVD player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the HDTV set top box or DVD player to the INPUT (AUDIO/L) jack. 4. Press the VID1 button to view the program from theHDTV set top box or DVD player. The VIDEO label disappears automatically after approximately four seconds. 5. Press ANT button to return to the previous channel. PB PR PB PR DVI-HDTV ANT A TO CONVERTER ANT B L Y R (MONO)/L AUDIO TO HI-FI R S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT DIGITAL OUTPUT CAPABILITY DIGITAL OUTPUT L R OUTPUT AUDIO AUDIO AUDIO Models: 51/57UWX20B 51/57GWX20B

19 CONNECTING A COMPONENT SOURCE TO INPUT 1 OR 2: Y-PBPR. 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set at right. 2. Connect the cable from the CB/PB OUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB) jack. 3. Connect the cable from the CR/PR OUT or R-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PR) jack. 4. Connect the cable from the AUDIO OUT R of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/R) jack. 5. Connect the cable from the AUDIO OUT L of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/L) jack. 6. Press the VID1~VID2 button, to view the program from the Laserdisc/DVD player or HDTV set top box. The VIDEO label disappears automatically after approximately four seconds. 7. Press the ANT button to return to the previous channel. NOTE: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is played back will be abnormal if the connection is loose. 2. See page 13 for tips on REAR PANEL CONNECTIONS. PB PR PB PR PB PR PB PR DVI-HDTV DVD Player OUTPUT PR PB Y L R AUDIO AUDIO ANT A TO CONVERTER ANT B Y R (MONO)/L S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT DVD Player OUTPUT PR PB Y L R AUDIO AUDIO ANT A TO CONVERTER ANT B Y R (MONO)/L S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT L AUDIO TO HI-FI R L AUDIO TO HI-FI R Model: 43FWX20B Models: 51/57UWX20B 51/57GWX20B

In addition to controlling all the functions on your HITACHI Projection TV, the new remote control is designed to operate different types of VCRs, CBL (Cable TV) converters, satellite receiver, DVD players, and other audio/video equipment with one touch. Basic operation keys are grouped together in one area. To operate your TV, point the remote control at the remote sensor of the TV and press the TV button. The remote will now con- trol your television. To operate your cable/satellite box, point the remote at the remote sensor of the cable/satellite box and press the CABLE/SATEL- LITE (CBL/SAT) button. The remote will now control your cable/satellite box. (See page 29 for instructions on how to program the remote to control your cable box.) To operate your DVD/VCR player, point the remote at the remote sensor of the DVD/VCR player and press the DVD/VCR but- ton. The remote will now control your DVD/VCR player. (See pages 28 and 30 for instruction on how to program the remote to control your DVD/VCR player.) These buttons allow the remote to control your TV, VCR, DVD or cable/satellite box depending on which mode is chosen, as explained above. TV OR VCR/DVD BUTTONS When in TV mode, these buttons, except the REC button, will select from five video input sources. When in VCR/DVD mode, these buttons transmit the chosen precoded VCR/DVD codes. 1 2 3 4 5 6 7 8 9 0 ANT INFO VOL CH POWER TV CBL/SAT DVD/VCR PIP SWAP PIP MODE FREEZE VIDEO MENU MUTE EXIT LAST CH REC ASPECT VIRTUAL HD SELECT PIP CH CLU-4321UG VID1 VID2 VID3 VID4 VID5

POWER button Press this button to turn the TV set on or off when the remote is in TV mode.  PICTURE-IN-PICTURE buttons See separate section on pages 25, 26 and 27 for description.
VIDEO button Press this button to directly access the VIDEO adjustment menu.  SELECT, MENU, CURSOR buttons All the On-Screen Display features can be set or adjusted by using the CURSOR buttons, except for numeric entries. The CURSOR will highlight functions or adjust and set different features. Press the CURSOR toward desired direction then press the SELECT button to select. When no on-screen displays are on the TV screen, use CURSOR  or
to access the Favorite Channels feature. To add channels to Favorite Channels, use the number keys to enter the channel number. Use CURSOR
to highlight “Add”, then press SELECT to store the channel to the Favorite Channel feature. To delete (Del) the channel from the Favorite Channel, use CURSOR  ,  to highlight the channel, then CURSOR
to highlight Delete (Del) and press SELECT to delete. To view a Favorite Channel use CURSOR  ,  to highlight the channel and press SELECT to view. VOLUME, MUTE buttons 1 2 3 4 5 6 7 8 9 0 INFO VOL CH POWER TV CBL/SAT DVD/VCR PIP SWAP FREEZE VIDEO MENU MUTE EXIT LAST CH REC ASPECT VIRTUAL HD SELECT PIP CH SELECT, MENU, CURSOR buttons PICTURE-IN-PICTURE VIDEO button CHANNEL SELECTOR buttons ANT button PIP CH button  TV POWER button 
     EXIT button LAST CHANNEL (LAST CH) button INFO button VIRTUAL HD button ANT PIP MODE CLU-4321UG VID1 VID2 VID3 VID4 VID5 VID1~VID5 buttons ASPECT button  MENU button  Contrast 100% Next/Prev SEL Return Change Value VIDEO EXIT Favorite Channels Move Ant A 8 A 6 A 3 - - - - - - - - - - - - - - - - - - - - - - - - - CURSOR CURSOR Add SEL Select Favorite Channels Move Ant A 8 A 8 A 6 A 3 - - - - - - - - - - - - - - - - - - - - Del 8 SELECT

CONTROL YOUR TV  CHANNEL selector buttons CHANNEL selector buttons are used to select channels, lock access code, etc. Enter one, two, or three numbers to select channels. Enter “0” first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the “1” button, wait until two dashes appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons. Channel selection may also be performed by pressing CH up () or down ().  ANTENNA button The ANT button will select between Antenna A and Antenna B each time the button is pressed. NOTE: The TV may not receive some channels if you are not in the correct ANTENNA/CABLE mode. (see page 51) Ant B 28 Ant A 10 ANT VID1 ~ VID5 When the remote control is in TV mode, press these buttons to directly select the video input sources between the five video inputs. When the remote control is in Set-Top-Box mode (STB) these buttons will control the Set-Top-Box or satellite receiver, and execute the secondary function labeled. Ant A 28 TAKA YPBPR:1 VID1 Stereo ST/SA Video:2 VID2 Video:4 VID4 Video:5 VID5 Video:3 VID3 ANT VID1 VID2 VID3 VID4 VID5  VOLUME, MUTE button Press the VOLUME up () or down () button until you obtain the desired sound level. To reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc., press the MUTE button. Press the MUTE button again to turn the sound off completely (MUTE). To restore the sound, press the MUTE button one more time, or press the VOLUME Up () button. Closed Captioning will display when MUTE/SOFT MUTE is on and Closed Caption is set to AUTO (See page 56). ▲ ▲ Volume 8 ▲ ▲ Mute 8 ▲ ▲ Soft Mute 8 MUTE MUTE

CONTROL YOUR TV  ASPECT button Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal, the picture format ratio allows you to adjust the images through the following options. 4:3 STANDARD Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the left and right of the image to preserve the original aspect ratio of the source. Note: Use this mode for only 15% of your total viewing time to prevent uneven aging of the phosphors. Phosphors in the lighted area of the picture will age more rapidly than the gray areas. 4:3 EXPANDED Use this aspect mode to display conventional (4:3) sources by expanding the outer edges of the image to fill the 16:9 screen. The center of the image remains unaltered. 4:3 Zoom1/Zoom2 Use these aspect modes to zoom in on conventional (4:3) sources. 16:9 STANDARD Use this aspect mode to display 16:9 sources like HDTV and DVD’s preserving the original 16:9 aspect ratio. 16:9 Zoom Use this aspect to Zoom-in once while in 16:9 aspect. (1) NTSC Input (2) 480i/480p INPUT (3) 720p/1080i INPUT 4:3 INPUT 4:3 EXPANDED 4:3 ZOOM1 4:3 ZOOM2 16:9 STANDARD 4:3 STANDARD 16:9 INPUT 4:3 EXPANDED 4:3 ZOOM1 4:3 ZOOM2 16:9 STANDARD 4:3 STANDARD INPUT 16:9 16:9 STANDARD 16:9 ZOOM 16:9 ZOOM 16:9 ZOOM

 VIRTUAL HD button Press this button to toggle between 1080i and 540p.  INFO button Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second audio program (SAP), the time and CHANNEL ID. EXIT button When in MENU mode, this button will exit all On-Screen Displays. LAST CHANNEL (LAST CH) button Use this button to select between the last two channels viewed. (Good for watching two sporting events, etc.)  PIP CH button Use the PIP CH button to select between main picture and sub-picture tuning. The channel number which is highlighted indicates what channel is being controlled.  MENU button The MENU button will start the On-Screen Display. Ant A 10 Ant A 39 LAST CH Stereo (480i) ST/SA Audio Broadcast Audio Selected Main Picture Source Channel ID/Video ID Time PIP/Sub-Picture Source Signal Format Received TV-PG DLSV PIP TV-PG DLSV Broadcast Rating 16:9 Standard 1080i Movies C.C. On Off 10:05 AM Time Lock 10:05 AM Wide Mode Virtual HD Picture Mode Closed Captioning Off Timer TV Time Lock Ant A 15 ABCDEFG 10:10 AM PIP Ant A 10 PIP/Sub-Picture OFF Main Picture When an S-VIDEO Input is connected to VIDEO: 3. When a COMPONENT VIDEO: Y-PBPR Input is connected to VIDEO: 1. YPBPR:1 S - IN: 3

V:2, V:3, V:4, or V:5). You may also view the VCR program as a main picture while viewing another program as a sub-picture (ANT A, V:1, V:2, V:3, V:4, or V:5).  PIP button Press the PIP button and a sub-picture will appear in one of the four different modes (POP, PIP, SPLIT or SURF), depending on the last selection of the PIP mode. To change the PIP mode, use the PIP MODE button to cycle through the four different modes. POP MODE PICTURE-IN-PICTURE Press the PIP button and a sub-picture appears in one of the four different modes (POP, PIP, SPLIT or SURF), depending on the last selection of the PIP mode. Press the PIP button again to remove the sub-picture from the screen. Use the PIP CH button to select between main and sub-picture tuning control (indicated by green highlighted channel display.) Press the VID1, VID2, VID3, VID4 or VID5 button when sub-picture channel tuning is being controlled, to change between VIDEO: 1, VIDEO: 2, VIDEO: 3, VIDEO:4 and VIDEO:5 and ANT:A source. (ANT B source cannot be viewed as a sub-picture.) PIP MODE PICTURE-IN-PICTURE (This feature is only available in 1080i input signal) To prevent a pattern burn, occasionally move the sub-picture using the CURSOR ,
, , . PICTURE-IN-PICTURE (PIP) NOTES: 1. When ANT B is selected as the main channel, the SWAP feature is disabled. 2. In POP mode, CURSOR  ,  will move the sub-picture up/down. Ant A 10 Main Picture Sub Picture Ant A 10 PIP Your HITACHI Projection TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. The Dual Tuner can operate with only one input (ANT A only) or two inputs (ANT A and ANT B). ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture. To select between main picture and PIP sub-picture tuning, press the PIP CH button on the remote. The green highlighted channel display will move with every press of the PIP CH button. When the top channel display is highlighted, channel tuning is for the main picture. When the lower channel display is highlighted, channel tuning is for the PIP sub-picture. The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing other programs from the ANT A source or any of the video inputs. PIP POWER TV CBL/SAT DVD/VCR PIP SWAP PIP MODE FREEZE VIDEO MENU MUTE EXIT LAST CH PIP CH  
, SELECT PB PR PB PR OUTPUT Audio Video VCR ANT A TO CONVERTER ANT B Y R (MONO)/L S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT AUDIO AUDIO AUDIO L AUDIO TO HI-FI R PB PR PB PR OUTPUT Audio Video VCR ANT A TO CONVERTER ANT B Y R (MONO)/L S-VIDEO S-VIDEO S-VIDEO Y/VIDEO R (MONO)/L R (MONO)/L VIDEO R (MONO)/L VIDEO R L VIDEO INPUT 1 INPUT 2 INPUT 3 INPUT 4 MONITOR OUT AUDIO AUDIO AUDIO L AUDIO TO HI-FI R DVI-HDTV PIP Ant A 10 Model: 43FWX20B Models: 51/57UWX20B 51/57GWX20B

Split Mode PIP displays the main picture and sub-picture evenly on the screen. SURF MODE PICTURE-IN-PICTURE This feature will automatically scan all active channel numbers (those set in memory) and display them as PIP sub-pictures, Press the PIP button a second time to remove the sub-pictures from the screen.  SWAP button If you wish to switch what is being shown on the main picture to the sub-picture, press the SWAP button. NOTES: 1. If no buttons are pressed when in SURF mode, auto-scanning will continuously scan channels in memory. (see page 42) 2. If a channel is tuned during this SURF scanning, sub-pictures will be removed from the screen. 3. SURF MODE PIP is allowed only when ANT A or ANT B is selected as the main channel. 4. If MOVIE/TV RATINGS lock functions setting is ON, SURF mode will be deactivated. 5. Closed Caption will not appear when SURF mode is on. NOTES: 1. The SWAP button will only operate in POP/SPLIT PIP mode. 2. The SWAP function will not operate if ANT B input is set as the main channel (ANT B input cannot be displayed as a sub-picture.) Ant A 28 Ant A 10
PIP MODE button To change between the different PIP modes (POP, PIP, SPLIT or SURF) press the PIP MODE button when PIP is ON. Each press of this button will change PIP to a different mode. PIP MODES will depend on the type of input signal. PIP PIP MODE PIP MODE Ant A 12 Ant A 10 Ant A 12 PIP MODE PIP PICTURE-IN-PICTURE (PIP) MODES POP PIP SPLIT SURF YES x YES YES YES x YES x x x YES x x x YES x x YES YES x NTSC (ANT A/B) 480i 480p 720p 1080i Ant A 10 Ant A 12 Main Picture Sub Picture SWAP SPLIT Ant A 12 Ant A 10 Ant A 10 Ant A 12 09 10 12 09 10 12

If you wish to freeze the sub-picture, press the FREEZE button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the FREEZE button again.  FREEZE button (with PIP OFF) Press the FREEZE button to freeze the picture, depending on the PIP mode selected (POP Sub Freeze, SPLIT or STROBE). To change FREEZE modes, use the PIP MODE button to cycle through the three different modes. POP SUB FREEZE (with PIP OFF) PIP should be in POP mode. Press the FREEZE button to freeze. Press the FREEZE button again to return to normal viewing. NOTES: Each freeze frame is delayed about 0.1 (1/10) second. NOTE: When PIP is on, the FREEZE function will only operate when POP/PIP/SPLIT mode is chosen. Hot Springs Clay Mask C/O John Doe Run-Spa Retreat P.O. Box 55512 Any Town, USA 98765 Check or Money Order Only 1-800-555-1212 STROBE FREEZE(with PIP OFF) PIP should be in SURF mode. Press the FREEZE button to freeze three frames of the picture you are currently viewing. Press this button again or PIP to return to normal viewing. This feature is useful for viewing a moving picture that has many details, for example, a close play in a sporting event or a golf swing. FREEZE FREEZE FREEZE FREEZE SPLIT FREEZE(with PIP OFF) PIP should be in SPLIT mode. Press the FREEZE button to freeze the picture you are currently viewing (only the right sub-picture will freeze). Press the FREEZE button again and press the PIP button to return to normal viewing. Ant A 12 FREEZE Main Picture Sub Picture Ant A 10 Hot Springs Clay Mask C/O John Doe Run-Spa Retreat P.O. Box 55512 Any Town, USA 98765 Check or Money Order Only 1-800-555-1212 FREEZE

Operating the precoded function for your VCR. This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR. (refer to page 31 for pre-codes) 1. Turn ON your VCR. 2. Aim the remote control at the front of your VCR. 3. Press and release the DVD/VCR button to switch to VCR pre-coded mode. 4. Hold down the DVD/VCR button on the remote and enter the two digit preset code that matches your VCR, as shown on page 31. 5. Aim the remote at the VCR and press the POWER button. The remote will turn off your VCR when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your VCR. If the VCR does not turn off, try a different two digit preset code. 6. The remote will now control your VCR. NOTES: 1. If your VCR cannot be operated after performing the above procedures, your VCR’s code has not been precoded into the remote. 2. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult your VCR operating guide. 3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.  DVD/VCR Button This button allows the remote to control your VCR by set- ting it to VCR mode.  PRECODED VCR Buttons These buttons transmit the chosen precoded VCR codes. For some VCRs, you must press the RECORD button twice to record a program.
EXCLUSIVE TV Buttons These buttons are for operating the TV. 1 2 3 4 5 6 7 8 9 0 ANT INFO VOL CH POWER TV CBL/SAT DVD/VCR PIP SWAP PIP MODE FREEZE VIDEO MENU MUTE EXIT LAST CH REC ASPECT VIRTUAL HD SELECT PIP CH CLU-4321UG VID1 VID2 VID3 VID4 VID5 
 MY VCR CODE IS: NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR.

CABLE/SATELLITE BOX FUNCTIONS Operating the precoded function for your cable/satellite box. This remote is designed to operate different types of cable/satellite boxes. You must first program the remote to match the remote sys- tem of your cable/satellite box. (refer to page 31) 1. Turn ON your cable/satellite box. 2. Aim the remote control at the front of your cable/satellite box. 3. Press and release the cable/satellite (CBL/SAT) button to switch to cable/satellite pre-coded mode. 4. Hold down the CBL/SAT button on the remote and enter the two digit preset code that matches your cable/satellite box as shown on page 31. 5. Aim the remote at the cable/satellite box and press the POWER button. The remote will turn off your cable/satellite box when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable/satellite box. If the box does not turn off, try a different two digit preset code. 6. The remote will now control your cable/satellite box. NOTES: 1. If your cable/satellite box cannot be operated after performing the above procedures, your cable/satellite box code has not been precoded into the remote. 2. In the unlikely event that your cable/satellite box cannot be operated after performing the above procedures, please consult your cable/satellite box operating guide. 3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.  CABLE (CBL/SAT) button This button allows the remote to control your cable/satellite box by setting it to CABLE/SATELLITE mode.  PRECODED CABLE/SATELLITE BOX buttons These buttons transmit the chosen precoded cable/satellite codes.
EXCLUSIVE TV buttons These buttons are for operating the TV. 1 2 3 4 5 6 7 8 9 0 ANT INFO VOL CH POWER TV CBL/SAT DVD/VCR PIP SWAP PIP MODE FREEZE VIDEO MENU MUTE EXIT LAST CH REC ASPECT VIRTUAL HD SELECT PIP CH CLU-4321UG VID1 VID2 VID3 VID4 VID5 
 MY CABLE/SATELLITE BOX CODE IS: NOTE: Refer to instruction manual of the Cable/Satellite Box for operation of the buttons exclusively for the Cable/Satellite Box.

DVD FUNCTIONS Operating the precoded function for your DVD player. This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player. (refer to page 31 for pre-codes) 1. Turn ON your DVD player. 2. Aim the remote control at the front of your DVD player. 3. Press and release the DVD/VCR button to switch to DVD pre-coded mode. 4. Hold down the DVD/VCR button on the remote and enter the two digit preset code that matches your DVD player, as shown on page 31. 5. Aim the remote at the DVD player and press the POWER button. The remote will turn off your DVD player when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not turn off, try a different two digit preset code. 6. The remote will now control your DVD player. NOTES: 1. If your DVD player cannot be operated after performing the above procedures, your DVD player’s code has not been precoded into the remote. 2. In the unlikely event that your DVD player cannot be operated after performing the above procedures, please consult your DVD player operating guide. 3. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.  DVD/VCR Button This button allows the remote to control your DVD player by setting it to DVD mode.  PRECODED DVD Buttons These buttons transmit the chosen precoded DVD codes.
EXCLUSIVE TV Buttons These buttons are for operating the TV. 1 2 3 4 5 6 7 8 9 0 ANT INFO VOL CH POWER TV CBL/SAT DVD/VCR PIP SWAP PIP MODE FREEZE VIDEO MENU MUTE EXIT LAST CH REC ASPECT VIRTUAL HD SELECT PIP CH CLU-4321UG VID1 VID2 VID3 VID4 VID5 
 MY DVD PLAYER CODE IS: NOTE: Refer to instruction manual of the DVD player for operation of the buttons exclusively for the DVD player.

CODES FOR REMOTE CONTROL CABLE BRAND CODE General Instrument . . . . . . . . . . . . . . . . . . . . . . . . .17 Hamlin . . . . . . . . . . . . . . . . . . . . . . . . . . .22,23,24,25 Jerrold . . . . . . . . . . . . . . .00,01,02,03,04,05,06,07,21 Oak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26,27,28 Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . .18,19,20 Pioneer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13,14 Scientific Atlanta . . . . . . . . . . . . . . . . . . . . . .08,09,10 Tocom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15,16 Zenith . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11,12 SATELLITE BRAND CODE Ecostar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Hitachi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Hughes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 RCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30, 35 Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 VCR BRAND CODE Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Daewoo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Emerson . . . . . . . . . . . . . . . . . . . . . . .20,21,22,23,24 Fisher . . . . . . . . . . . . . . . . . . . . . . . . . . .34,37,38,39 Funai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 General Electric . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Goldstar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Hitachi . . . . . . . . . . . . . . . . . . . .00,01,02,03,04,05,06 JVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18,49,50,51 Magnavox . . . . . . . . . . . . . . . . . . . . . . . . . .12,13, 14 Mitsubishi . . . . . . . . . . . . . . . . . . . . . . . . .27,28,29,30 NEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40,41 Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10,11 Philips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . .17,25,26 Scott . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Sharp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31,32 Shintom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .07,08,09 Symphonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Teknica . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 DVD BRAND CODE Hitachi . . . . . . . . . . . . . . . . . . . . . . . . . . . .53, 59, 60 Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Pioneer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 RCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 Sanyo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

2. Press the CURSOR ,
, ,  to highlight a different feature. 3. Press EXIT on the remote control to quickly exit from a menu. 4. Press CURSOR  or
to access Favorite Channels menu. HELP MENU EXIT SELECT Setup Locks Ch. Manager Audio Video Move SEL Sel This part of the screen shows which selections are available. This part of the screen shows which Remote Control buttons to use.

and Music. Contrast Adjust contrast. Brightness Adjust brightness. Color Adjust color. Tint Adjust tint. Sharpness Adjust sharpness. Vertical Position Centering top and bottom of the picture. Magic Focus Automatic or manual alignment of the Red, Green and Blue colors to make white. Color System Automatically change tint and color coordinates for DTV program. Advanced Settings Improve picture performance. Treble Adjust the treble. Bass Adjust the bass. Balance Adjust the balance. Sound Enhancement Set SRS and BBE surround settings. Advanced Settings Improve sound performance. Ant A View/edit Channel ID, Scan, and Lock settings in antenna A. Ant B View/edit Channel ID, Scan, and Lock settings in antenna B. Change Access Code Change Lock access code. Engage Lock Choose to lock channel, video input, and front panel. TV Time Lock Set specific time to Lock TV. Movie Ratings Block various types of movies and video types based on motion picture ratings. TV Ratings Block various types of movies and television programming based on a parental guide ratings. Canadian Ratings (ENG) Block various types of movies and television programming based on the Canadian ratings system. Canadian Ratings (FRN) Block various types of movies and television programming based on the Canadian French ratings system. Menu Preference Choose English, French, or Spanish text. Set The Clock Set the TV clock. It must be set before using Lock feature. Set The Channels Set Channel Source and Auto Channel Scan. Set The Inputs Label Video Inputs , VCR, DVD, etc. Set Event Timer Turn TV on and off once, daily, or weekly. Set Closed Captions Feature to display dialogue/text. About Your TV Information display for this TV. Video Audio Channel Manager Locks Setup

Video Use CURSOR  or  to highlight Picture Mode settings. When SPORTS mode is selected, the following are automatically set: CONTRAST - 100%, COLOR TEMPERATURE - HIGH, LOUDNESS - OFF, PERFECT VOLUME - OFF, SURROUND - SRS and BBE. When MOVIES mode is selected, the following are automatically set: CONTRAST - 60%, COLOR TEMPERATURE - STANDARD, BASS - 63%, LOUDNESS - OFF, PERFECT VOLUME - OFF, SURROUND - SRS and BBE. . When NEWS mode is selected, the following are automatically set: CONTRAST - 75%, COLOR TEMPERATURE - MEDIUM, LOUDNESS - ON, PERFECT VOLUME - ON. When MUSIC mode is selected, the following are automatically set: CONTRAST - 100%, COLOR TEMPERATURE - HIGH, LOUDNESS - OFF, PERFECT VOLUME - OFF, SURROUND - BBE. You can customize each of the above modes (SPORTS, MOVIES, NEWS, and MUSIC) to your preference to increase viewing per- formance and pleasure, depending upon the video program being viewed. However, if RESET is selected, each mode will reset to the initial conditions as explained above. If RESET is selected in SPORTS mode, only SPORTS mode will return to factory conditions. Press EXIT to quit menu or select PICTURE MODE to return to previous menu. Use this function to choose from automatic picture settings to optimize your TV’s performance. Picture Mode Color Brightness Contrast Picture Mode Video Move SEL Select Vertical Position Sharpness Tint Advanced Settings Color System 100% 50% 50% 50% 0 Setup Locks Ch. Manager Audio Video Move SEL Sel Picture Mode Video Move SEL Return Sports Movies News Music Reset Magic Focus Sports CURSOR MENU CURSOR CURSOR NOTE: MOVIE MODE 3:2 PULLDOWN DETECTION SPECIAL FEATURE Theatrical movies are shot on film at 24 frames or still pictures per second, instead of 30 frames or 60 fields like video. When film is transferred to video for television viewing, the disparity between the two frame rates must be reconciled. This involves a process known as 3:2 pulldown. When MOVIE mode is selected from the Picture Mode menu, your Hitachi Projection Television will activate the circuitry for this special feature to improve video performance when watching film based sources. This 3:2 pulldown detection will only work in MOVIE mode.

will only affect the picture when ADVANCED SETTINGS DIMMER is OFF. Use the CURSOR  or  to highlight the function to be adjusted. Press the CURSOR  or
to adjust the function. Press MENU to return to main menu or select PICTURE MODE to return to previous menu. Press EXIT to quit menu. Use this function to adjust the level of color in the picture. Use this function to adjust overall picture brightness. This function allows you to select when aspect style is either 4:3 EXPANDED/ZOOM1/ZOOM2. Vertical position can be changed with this mode. Adjustable range is -10 (video center is toward bottom of screen) to +10 (video center is toward top of screen). Contrast Color Brightness Vertical Position NOTES: 1. If CONTRAST is selected, you are adjusting CONTRAST. The additional menu items BRIGHTNESS, COLOR, TINT, and SHARPNESS can be selected and adjusted in the same manner. 2. It may be necessary to adjust TINT to obtain optimum picture quality when using the COMPONENT VIDEO Y-PBPR input jacks. 3. If you are using the COMPONENT VIDEO input jacks (Y-PBPR) and notice that the TINT and COLOR are abnormal, check to make sure that VIDEO-Color System is set properly. Use this function to adjust flesh tones so they appear natural. Tint Use this function to adjust the amount of fine detail in the picture. Sharpness

Please turn ON your television for at least 20 minutes before using this feature. The Magic Focus button on control panel will not work when adjustment mode is set to Manual (see page 37). Your HITACHI Projection TV has three color projection tubes: one for red, one for green, one for blue. When mixed together in the proper proportion, the output of these three color tubes can produce any color. To produce these colors, however, the beams must be precisely aligned over each other so that the colors can be mixed. The process of aligning these picture beams is called “convergence”. Over a period of time, the picture tubes can drift out of alignment due to normal bumps and vibrations or moving the TV. If you move your TV, or if, after a time, you notice color rings or halos around objects in the picture, you may want to converge (align) the colors. Properly converged, the lines appear white, which is actually a combination of the outputs of the three color tubes. The output of the green tube is stationary. The outputs of the red and blue tubes can be adjusted. When properly aligned, the outputs of all three tubes should be directly over each other to produce the white lines. To simplify convergence, HITACHI incorporates a function called MAGIC FOCUS located on the front control panel, which allows the TV to self-adjust. Press this MAGIC FOCUS button and the convergence self adjustment will start and this process will take approximately 20 seconds. If this button is pressed during this process, no change in picture quality will occur. After this 20 second self-adjust period, picture quality will be optimum. (Do not move the TV during self-adjust.) You may also select Magic Focus from the VIDEO menu. NOTES: Only a momentary press of the MAGIC FOCUS button is necessary to start AUTO DIGITAL CONVERGENCE. At any time during this convergence correction process, you may press the MAGIC FOCUS button to exit the MAGIC FOCUS mode. However, the convergence correction process needs to be completed to SAVE the new corrected convergence data. Magic Focus Video Move SEL Return Aligns the Red, Green, and Blue colors to correct for Magnetic Influences. Auto Manual Setup Locks Ch. Manager Audio Video Move SEL Sel Color Brightness Contrast Picture Mode Video Move SEL Select Vertical Position Sharpness Tint Advanced Settings Color System 100% 50% 50% 50% Magic Focus Sports Adjustment Mode If you want to adjust now Start MAGIC FOCUS CURSOR CURSOR CURSOR SELECT CURSOR MENU

2. Auto Adjustment Mode is recommended. If convergence is still not acceptable, use the Manual Adjustment Mode. DO NOT press MAGIC FOCUS or use Auto Adjustment Mode after using Manual Adjustment Mode. Manual Convergence Adjustment Mode Using the Remote Control, select VIDEO-MAGIC FOCUS-MANUAL ADJUSTMENT MODE-START to access convergence crosshatch pattern. The adjustment point is indicated by the Adjustment Point Cursor. To Move Adjustment Point To move adjustment point, the Adjustment Cursor must be WHITE. Use the CURSOR ,
, ,  to move the Adjustment Cursor. Another way to move the Adjustment Point Cursor is to press the followiing buttons: [2] up, [4] left, [5] down, [6] right. If you use the number buttons while the adjustment point is WHITE, it will change to RED. To Change the Color of Adjustment Point Press the SELECT button repeatedly (WHITE-RED-BLUE-WHITE...). Green color is fixed and cannot be adjusted. To Adjust the Convergence Move the Adjustment Cursor to the point to be adjusted. Use the CURSOR ,
, ,  to match the RED and BLUE colors to GREEN (reference color). Properly aligned, all three colors should appear white. If convergence is acceptable after Manual Convergence adjustment, press EXIT button to access menu mode. Press the [1] button on the remote control to SAVE adjusted data and return to main picture. Press the [2] button on the remote control to CANCEL adjusted data and return to main picture. Press the [3] button on the remote control to recall the factory pre-set convergence data. Press the [4] button on the remote control to return to the manual convergence adjustment mode (crosshatch pattern). Press the [9] button on the remote control to read the SAVED data. Magic Focus Video Move SEL Return Aligns the Red, Green, and Blue colors to correct for Magnetic Influences. Auto Manual Setup Locks Ch. Manager Audio Video Move SEL Sel Color Brightness Contrast Picture Mode Video Move SEL Select Vertical Position Sharpness Tint Advanced Settings Color System 100% 50% 50% 50% Magic Focus Sports Adjustment Mode If you want to adjust now Start CURSOR MENU CURSOR CURSOR SELECT CURSOR DONE : [1] CANCEL : [2] INI. RESET : [3] BACK : [4] EXIT Adjustment Point Cursor

settings to produce the highest quality picture possible. When ADVANCED SETTINGS is highlighted, press SELECT or CURSOR to access an ADVANCED SETTINGS feature. Use CURSOR ,  to highlight functions. Press the SELECT button to select the function setting. When the function has an “✓” in the box, it is ON. Press the SELECT button to change COLOR TEMPERATURE setting. When the function shows a “ “, it is selected. Press EXIT to quit menu or CURSOR  to return to previous menu. Color Temperature Set this to High for less intense colors with more blue (9,300K), set to Medium for hotter colors with more red (7,500K), or set to Standard for standard colors (6,500K). Dimmer Turn ON the Dimmer to reduce picture contrast and brightness automatically when viewing in a dark room. Auto Color The AUTO COLOR function automatically monitors and adjusts the color to maintain constant color levels even after a program or channel changes. It also maintains natural flesh tones while preserving fidelity of background colors. Noise Reduction The NOISE REDUCTION function automatically reduces conspicuous noise in the picture without degrading picture quality. When the Noise Reduction feature is ON, the Sharpness feature is disabled. Scan Velocity Modulation The Scan Velocity Modulation function automatically enhances the edges between light and dark areas. Black Level Expansion The BLACK LEVEL EXPANSION function automatically enhances shadow detail in dark scenes. Black Side Panel The BLACK SIDE PANEL function turns the gray side bars on/off when watching 4:3 signals in Standard mode. The top/bottom gray bar will appear in SPLIT MODE PIP and SPLIT FREEZE. Advanced Settings Advanced Settings Video Move SEL Return Color Brightness Contrast Picture Mode Video Move SEL Select Vertical Position Sharpness Tint Advanced Settings Color System 100% 50% 50% 50% 0 Color Temperature High Medium Standard Dimmer Auto Color Noise Reduction Scan Velocity Modulation Black Level Expansion Black Side Panel Advanced Settings Video Move SEL On/Off Color Temperature High Medium Standard Dimmer Auto Color Noise Reduction Scan Velocity Modulation Black Level Expansion Black Side Panel Magic Focus Sports CURSOR CURSOR SELECT CURSOR NOTE: To prevent pattern burn when watching 4:3 signal, Black Side Panel is cancelled at Power OFF. It is recommended to watch 4:3 signal with gray side bar. This function allows you to automatically change tint and color coordinates for DTV programs. HDTV - High Definition Television - Use for High Vision Signal Y-PBPR from HDTV Set-Top Box. SDTV/DVD - Standard Definition Television or DVD (Digital Versatile Disc Player) Y-CBCR. Color System NOTES: 1. If Color System is set improperly (does not match actual input signal), the color and tint of the main picture will be abnormal. 2. You must be tuned to VIDEO: 1 or 2 inputs and have a component hooked up to the Y-PBPR input jacks to access this color system. 3. All component color type settings will affect only color component input you are currently viewing. If you are using both sets of component input jacks, be sure to set the color system feature for both inputs.

Audio Setup Locks Ch. Manager Audio Video Move SEL Sel Next/Prev Change Value Return SEL Sound Enhancement Balance Bass Treble Audio Move SEL Return 50% 50% Sound Enhancement Balance Bass Treble Audio Move SEL Select 50% 50% Treble 50% Advanced Settings Advanced Settings L R L R CURSOR MENU CURSOR CURSOR CURSOR This function controls the low frequency audio to all speakers. Use CURSOR ,  to highlight functions. Press the SELECT button to select the function setting. Press CURSOR  or
to adjust the function. Press EXIT to quit MENU, or select Audio to return to the main menu. NOTE: If TREBLE is selected you are adjusting treble. The additional menu items Bass and Balance can be selected and adjusted in the same manner. This function controls the high frequency audio to all speakers. This function will control the left to right balance of the TV internal speakers and the AUDIO TO HI-FI output. Bass Balance Treble

sports stadiums, movie theaters, etc. with only two speakers. Audio Move SEL Return Sound Enhancement Sound Enhancement Balance Bass Treble Audio 50% 50% SRS BBE Advanced Settings Move SEL Select CURSOR To enter SOUND ENHANCEMENT, use CURSOR  or  to highlight then press the SELECT button to select SOUND ENHANCEMENT of your choice. Press CURSOR  or  to highlight your sound enhancement choice, and press the SELECT button to select your choice. Based on the principles of the human hearing system, SRS technology delivers and exciting and realistic 3D Sound experience from just two external speakers (or) the two internal speakers of your HITACHI Television. If your HITACHI Television is connected to an external audio system, SRS will also create an incredible 3D sound experience from two speakers and even enhance a complete multi-speaker surround sound system. Technology Sound reproduction quality enhancement system. The BBE technology produces sound that is natural and crisp from just two speak- ers (or) the two internal speakers of your HITACHI television. If your HITACHI television is connected to an external audio system, BBE will also create an incredible crisp sound experience from two speakers and even more complete and accurate reproduction of the original performance. BBE brings to the listener’s ear a more complete and accurate reproduction of the original performance. Each voice, speaking or singing, each instrument or sound effect is presented with its attendant harmonics or partials more clearly audible. The ear can then more easily recognize the unique tonal colors of each sound as though the sound was being produced live. NOTES: *SRS and the symbol are registered trademarks of SRS Labs, Inc. SRS technology is incorporated under license from SRS Labs, Inc. NOTES: Licensed by BBE Sound, Inc. under USP4638258, 5510752 and 5736897. BBE and BBE symbol are registered trade- marks of BBE Sound, Inc. Manufactured under license from BBE Sound, Inc.

Audio Source Multi-Channel Television Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural sound) used when receiving a weak stereo broadcast or SAP (second audio program) which may be a secondary language, weather report, etc. The mode you select will be displayed at the left edge of the TV. The source received will be displayed above the mode. See example below for each selection when both stereo and second audio are received (monaural is always received). Press CURSOR  or  to highlight a function. Press the SELECT button to select the function setting. When the function has a “✓” in the box it is ON. Advanced Settings Audio Move SEL Return Advanced Settings Sound Enhancement Balance Bass Treble Audio 50% 50% Audio Source Stereo Mono 2nd Audio Prog. Internal Speakers On Off Advanced Settings Move SEL Select Auto Noise Cancel Perfect Volume Loudness L R CURSOR Internal Speakers On - Select this feature if using the internal speakers only. Off - Select this feature if you prefer to use only speakers from a separate stereo system. Auto Noise Cancel This function eliminates the noise between stations. If a channel is tuned and is noisy, this function will automatically eliminate the audio for that channel. Perfect Volume This function will automatically adjust volume so each channel has the same average volume level. Loudness This function will improve the quality of both low and high frequency sounds when listening at low volume levels. Ant A 31 NEWS 10:00 PM Ant A 31 NEWS 10:00 PM STEREO SELECTED SAP SELECTED MONO SELECTED Stereo ST/SA Ant A 31 NEWS 10:00 PM SAP ST/SA Mono ST/SA Audio Selected Audio Broadcast

Press EXIT to quit menu. Ch. Manager Move SEL Return Ant A Ant B Ant A Ch. Manager CH# Scan CH ID Lock 2 Off -------- 3 Off -------- 4 Off -------- 5 Off -------- 6 Off -------- 7 Off -------- 8 Off -------- 9 Off -------- Move SEL Select CURSOR This function allows you to review which channels are labeled (CH ID), which have been added to Channel Memory (SCAN), and which are protected by LOCK. Channel Manager Use this feature after Auto Channel Scan is completed to add (On) or erase (Off) additional channels to the remote control channel  or  buttons. Scan To add (Scan-On) or erase (Scan-Off) additional channels while in Channel Manager, CURSOR  to highlight the channel number, then CURSOR  or  to highlight other channels. Once the desired channel is highlighted, CURSOR
to scan column, then CURSOR  or  to select ON or OFF. Ch. Manager Move SEL Return Ant A CH# Scan CH ID Lock 2 Off -------- 3 Off -------- 4 Off -------- 5 Off -------- 6 Off -------- 7 Off -------- 8 Off -------- 9 Off -------- Ch. Manager Move SEL / Ant A CH# Scan CH ID Lock 2 Off -------- 3 Off -------- 4 Off -------- 5 Off -------- 6 Off -------- 7 Off -------- 8 Off -------- 9 Off -------- Ch. Manager Move Set Ant A CH# Scan CH ID Lock 2 Off -------- 3 Off -------- 4 Off -------- 5 Off -------- 6 Off -------- 7 Off -------- 8 Off -------- 9 Off -------- Ch. Manager Ant A CH# Scan CH ID Lock 2 On -------- 3 Off -------- 4 Off -------- 5 Off -------- 6 Off -------- 7 Off -------- 8 Off -------- 9 Off -------- [ ] [ ] [ ] Move Set Return SEL Return SEL Return CURSOR CURSOR CURSOR NOTE: Lock feature can not be selected or set in CHANNEL MANAGER.

this feature to give up to 20 channels a name when ANTENNA signal source is selected and up to 60 channels a name when CATV signal source is selected. NOTES: 1. If ANT A and ANT B are in the same ANTENNA/CABLE mode, the CHANNEL ID for both antenna inputs will be the same. 2. CHANNEL ID will be displayed only when channel is displayed as main picture. Channel ID Channel Manager Move Edit (A-Z, 0-9, _, -) Ant A CH# Scan CH ID Lock 2 On -------- 3 On -------- 4 Off -------- 5 Off -------- 6 Off -------- 7 Off -------- 8 Off -------- 9 Off -------- Channel Manager SEL Return Ant A CH# Scan CH ID Lock 2 On A------- 3 On -------- 4 Off -------- 5 Off -------- 6 Off -------- 7 Off -------- 8 Off -------- 9 Off -------- Channel Manager Ant A CH# Scan CH ID Lock 2 On A------- 3 On -------- 4 Off -------- 5 Off -------- 6 Off -------- 7 Off -------- 8 Off -------- 9 Off -------- [ ] [ ] [ ] Move Edit (A-Z, 0-9, _, -) SEL Return Move Edit (A-Z, 0-9, _, -) SEL Return CURSOR CURSOR CURSOR

It can also be used to keep the TV from being viewed for a scheduled time period that you set. The code to enter the Locks feature is a four digit secret code number. The factory preset code is 0000. Use the number buttons to select access code. Locks Setup Locks Ch. Manager Audio Video Move SEL Sel Please Enter Access Code [ - - - - ] 0 0 0 0 Movie Ratings TV Time Lock Engage Lock Change Access Code Locks TV Ratings Move SEL Return Canadian Ratings (Eng) Canadian Ratings (Frn) [# Keys] Enter Code CURSOR NOTE: 1. If ANT A and ANT B are in the same signal source mode (see page 51), when a channel is locked, it is locked on both antenna inputs. 2. When using TIME LOCK make sure the clock is set (see page 50). 3. Text appears on the screen to indicate that TV TIMED LOCK is activated. 4. If MOVIE/TV Ratings Lock and Closed Caption settings are ON, PIP SURF mode will be deactivated. Use CURSOR  or  to highlight function and then press the SELECT button. To change the access code number, select Change Access Code. Enter a new four digit key number you prefer. Select CHANGE ACCESS CODE to change factory preset code (0000) to your preference. When ENGAGE LOCK is selected, SET CHANNEL LOCK, SET INPUT LOCK, and SET FRONT PANEL LOCK can be set individually. When SET CHANNEL LOCK is turned on, the picture and sound for the chosen channel will be blocked out. When SET INPUT LOCK is turned on, the picture and sound for all video inputs and the picture and sound for channels 3, 4 will be blocked out. When FRONT PANEL LOCK is turned on, all buttons on the Front Panel will be deactivated, except the Power button. When TV TIME LOCK is turned on (❒TIME LOCK) you can set the BEGIN and END times (CURSOR
) and the TV cannot be viewed during that time period (Set clock first). Use CURSOR  or  to highlight ONCE (TV will time out one time only), DAILY (TV will time out every day), WEEKLY - SUN~WEEKLY - MON (TV will time out one time a week) or OFF (to dis- able this function). When MOVIE RATINGS is selected, you can block various types of movies and video tapes based on motion picture ratings. Picture- in-Picture will also be blocked automatically (see page 45). When TV RATINGS is selected, various types of television programming based on a parental guide ratings will be blocked. Picture-in-Picture will also be blocked automatically (see page 46). Use CANADIAN RATINGS to block various types of movies and television programs based on the two rating systems used in Canada that you feel may be inappropriate due to its content (see pages 47-48). If you forget your secret code, use the factory code 7777 to erase your key number. This will reset the secret code number back to the factory preset 0000. Press EXIT to quit the menu. ✔

content. Use CURSOR  or  to select the MOVIE RATING category that you want to block. Press SELECT to block the MOVIE RATING that you have selected. Once rating is selected, for example PG-13, all movies rated PG-13 and higher (R, NC-17, and X) will be blocked. Press EXIT to quit menu or select MOVIE RATING to return to the previous menu. Movie Ratings Locks Move SEL Return Movie Ratings Movie Ratings TV Time Lock Engage Lock Change Access Code Locks Status TV Ratings Move SEL Select Canadian Ratings (Eng) Canadian Ratings (Frn) Not Rated: G: PG: PG-13: R: NC-17: X: MENU CURSOR CURSOR Contains no rating. Not Rated (NR) and Not Applicable (NA) pro- grams. Movie has not been rated or ratings do not apply. Restricted. Under 17 requires accompanying parent or adult guardian. Parents strongly cautioned. Some material may be inappropriate for children under 13. Parental guidance suggested. Some material may not be suitable for children. General audiences. All ages admit- ted. Adults only No one 17 and under admitted. G PG PG-13 R NC-17 X NOT RATED (NR) Motion Picture Ratings Chart

Engage Lock Change Access Code Locks Status TV Ratings Move SEL Select Canadian Ratings (Eng) Canadian Ratings (Frn) TV-Y: TV-Y7: TV-YG: TV-PG: TV-14: TV-MA: Sub Rating D L S V FV MENU CURSOR CURSOR TV Parental Guide Ratings Chart Use TV RATINGS to block from showing any programs or movies you feel might have inappropriate content. Use CURSOR  or  to highlight the category that you want to block. Press SELECT to block the TV RATING that you have selected. Press EXIT to quit menu or select TV RATING to return to the previous menu. Parental guidance suggested. The program may contain infrequent coarse language, limit- ed violence, some suggestive sexual dialogue and situations. Directed to older children. Themes and ele- ments in this program may include mild physi- cal or comedic violence, or may frighten chil- dren under the age of 7. All children. The themes and elements in this program are specifically designed for a very young audience, including children from ages 2-6. General audience. It contains little or no vio- lence, no strong language, and little or no sex- ual dialogue or situations. TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA Parents strongly cautioned. This program may contain sophisticated themes, intense sexual situation, more intense violence and intensely suggestive dialogue. Mature audiences only. This program may contain mature themes, indecent language, graphic violence, and explicit sexual content. Fantasy Violence Violence Sexual Situation Adult Language Sexually Suggestive Dialogue. FV V S L D NOTE: If you Block TV-14D, you will still permit TV-MA programs; If you block TV-14DV, you will automatically block TV-MAV programs, but you will still permit TV- MALS programs. This means that the TV will block violence in TV-14 and higher (TV-MA), but not language and sex.

Movie Ratings TV Time Lock Engage Lock Change Access Code Locks Status TV Ratings Move SEL Select Canadian Ratings (Eng) Canadian Ratings (Frn) C: C8+: G: PG: 14+: 18+: MENU CURSOR CURSOR Canadian Ratings English Chart Use Canadian Ratings (Eng) to block any type of movie and television program in Canada that you feel might be inappropriate in its content. Use CURSOR  or  to select the CANADIAN RATINGS (Eng) category that you want to block. Press SELECT to set the CANADIAN RATINGS (Eng) that you have selected. Once rating is selected, for example C8+, all movies and television programs rated C8+ and higher (G, PG, 14+ and 18+) will be blocked automatically. Press EXIT to quit menu. C C8+ G PG 18+ 14+ Programming intended for children under age 8 - Violence Guidelines; Careful attention is paid to themes, which could threaten children’s sense of security and well- being. There will be no realistic scenes of violence. Depictions of aggressive behav- iour will be infrequent and limited to portrayals that are clearly imaginary, comedic or unrealistic in nature. Other Content Guidelines: There will be no offensive language, nudity or sexual content. Programming generally considered acceptable for children 8 years and over to watch on their own - Violence Guidelines: Violence will not be portrayed as the pre- ferred, acceptable, or only way to resolve conflict; or encourage children to imitate dan- gerous acts which they may see on television. Any realistic depictions of violence will be infrequent, discreet, of low intensity and will show the consequences of the acts. Other Content Guidelines: There will be no profanity, nudity or sexual content. General Audience - Violence Guidelines: Will contain very little violence, either physi- cal or verbal or emotional. Will be sensitive to themes which could frighten a younger child, will not depict realistic scenes of violence which minimize or gloss over the effects of violent acts. Other Content Guidelines: There may be some inoffensive slang, no profanity and no nudity. Parental Guidance - Programming intended for a general audience but which may not be suitable for younger children. Parents may consider some content inappropriate for unsupervised viewing by children ages 8-13. Violence Guidelines: Depictions of con- flict and/or aggression will be limited and moderate; may include physical, fantasy, or supernatural violence. Other Content Guidelines: May contain infrequent mild profani- ty, or mildly suggestive language. Could also contain brief scenes of nudity. Programming contains themes or content which may not be suitable for viewers under the age of 14 - Parents are strongly cautioned to exercise discretion in permit- ting viewing by pre-teens and early teens. Violence Guidelines: May contain intense scenes of violence. Could deal with mature themes and societal issues in a realistic fashion. Other Content Guidelines: May contain scenes of nudity and/or sexual activity. There could be frequent use of profanity. Adult - Violence Guidelines: May contain violence integral to the development of the plot, character or theme, intended for adult audiences. Other Content Guidlines: May contain graphic language and explicit portrayals of nudity and/or sex.

Movie Ratings TV Time Lock Engage Lock Change Access Code Locks Status TV Ratings Move SEL Select Canadian Ratings (Eng) Canadian Ratings (Frn) G: 8 ans+: 13 ans+: 16 ans+: 18 ans+: MENU CURSOR CURSOR Canadian Ratings French Chart Use CANADIAN RATINGS (FRN) to block Canadian French programs according to various pro- gram ratings that you feel might be inappropriate in its content. Use CURSOR  or  to highlight the category that you want to block. Press SELECT to set the CANADIAN RATINGS (FRN) that you have selected. Once rating is selected, for example 8 ans+, all movies and television programs rated 8 ans+ and higher will be automatically blocked. Press EXIT to quit menu or select CURSOR  to return to the previous menu. 8 + General - Not recommended for young children - Programming intended for a broad audience but contains light or occasional violence that could disturb young children. Viewing with an adult is therefore recommended for young children (under the age of 8) who can- not differentiate between real and imaginary portrayals. General - Programming intended for audiences of all ages. Contains no violence, or the vio- lence content is minimal or is depicted appropri- ately with humor or caricature or in an unrealis- tic manner. Programming restricted to adults - Contains constant violence or scenes of extreme violence. Programming is not suitable for children under the age of 16 - Contains frequent scenes of violence or intense violence. G 8 ans + 13 ans + 16 ans + 18 ans + Programming may not be suitable for chil- dren under the age of 13 - Contains either a few violent scenes or one or more sufficiently violent scenes to affect them. Viewing with an adult is therefore strongly recommended for children under 13.

function desired. This feature will allow you to select any one of three different languages for all on-screen displays. Use CURSOR  ,
to highlight the language of your choice. Press SELECT to select the highlighted language. Press EXIT to quit menu or select MENU PREFERENCE to return to previous menu. Menu Preference Setup Move SEL Return Menu Preferences Set The Language English Francais Español Set The Menu Background Shaded Solid Menu Preference Setup Setup Move SEL Select Menu Preferences Set The Language English Francais Español Set The Menu Background Shaded Solid Set The Channels Set The Clock Set The Inputs Move SEL Select Set Event Timer Set Closed Captions About Your TV CURSOR MENU CURSOR CURSOR Setup Setup Locks Ch. Manager Audio Video Move SEL Sel Set The Channels Set The Clock Menu Preference Setup Set The Inputs Move SEL Return Set Event Timer Set Closed Captions About Your TV MENU CURSOR CURSOR Use CURSOR  or  to select the sub-menu of your choice.

Use CURSOR  or  to set the time and date. Press CURSOR  or
to change position. Press EXIT to quit menu. Set The Clock Set The Channels Set The Clock Menu Preference Setup Set The Inputs Move SEL Select Set Event Timer Set Closed Captions Setup Move SEL Return Set The Clock Time : Sun --:-- AM Setup Move SEL Return Set The Clock Time : Sun --:-- AM Set About Your TV CURSOR CURSOR This function allows you to choose from two menu backgrounds. Use CURSOR  ,
to highlight SET THE MENU BACKGROUND (shaded or solid), and press the SELECT button to select setting. Press EXIT to quit menu or CURSOR  to return to previous menu. Select SOLID for a black background (no picture can be seen behind menu screen), or select SHADED for a light background. Set The Menu Background Setup Move SEL Select Menu Preferences Set The Language English Francais Español Set The Menu Background Shaded Solid CURSOR

Use CURSOR  ,
to highlight the correct signal mode. Press the SELECT button to select highlighted signal. Press EXIT to quit MENU or select ANT A to return to previous menu. Reception channels for each mode are shown at the left. Refer to your cable or TV guide for channel identification standards. Set The Channels Set The Channels Set The Clock Menu Preference Setup Set The Inputs Move SEL Select Set Event Timer Set Closed Captions Setup Move SEL Return Set The Channels Ant A Ant B Setup Move SEL Select Set The Channels Setup Move SEL Return Set The Channels Ant A Source Antenna Cable(1) Cable(2) Auto Channel Scan Start Setup Move SEL Select Set The Channels Ant A Source Antenna Cable(1) Cable(2) Auto Channel Scan Start Ant A Ant B About Your TV CURSOR CURSOR CURSOR CURSOR RECEPTION BAND CATV 1 OR CATV 2 AIR VHF 2 ~ 13ch UHF 14 ~ 69ch CATV CHANNEL VHF 2~13 Mid band A~1 A-5 ~ A-1 Super band J~W Hyper band W + 1 ~ W + 28 Ultraband W + 29 ~ W + 84 Indicated on the screen 2 ~ 13 14 ~ 22 95 ~ 99 23 ~ 36 37 ~ 64 65 ~ 125 NOTE: If certain CATV channel’s picture are poor or unable to be viewed in Cable (1) mode, select Cable (2).

unused channels when using CHANNEL UP () or DOWN (). If the EXIT button is pressed while AUTO CHANNEL SCAN function is engaged, programming will stop. If two antenna are connected, switch antenna inputs with the ANT button and repeat AUTO CHANNEL SCAN for the second antenna input. Remember to select the correct ANTENNA/CABLE mode before using AUTO CHANNEL SCAN. See CHANNEL MANAGER - SCAN to add or to erase additional channels (see page 42). Auto Channel Scan Setup SEL Cancel Set The Channels Ant A Setup Move SEL Select Set The Channels Ant A Source Antenna Cable(1) Cable(2) Auto Channel Scan Start Setup Move SEL Select Set The Channels Ant A Source Antenna Cable(1) Cable(2) Auto Channel Scan Start Auto Channel Scan Cancel Scanning Channel Number: 66 CURSOR SELECT

Press CURSOR , , ,
, to highlight the name of the video inputs. Press the SELECT button to select desired input name. Select RESET to set video names to original factory preset condition. Set The Inputs Setup Move SEL Return Set The Inputs Video1 Rename Video2 Rename Video2 Auto Link Video3 Rename Video4 Rename Video5 Rename Set The Channels Set The Clock Menu Preference Setup Set The Inputs Move SEL Select Set Event Timer Set Closed Captions Setup Move SEL Select Set The Inputs Setup Move SEL Return Set The Inputs List CAM DVD2 VCR CBL LD VCR1 DVD SAT VCR2 DVD1 STB Reset Video1 Rename Video2 Rename Video2 Auto Link Video3 Rename Video4 Rename Video5 Rename About Your TV Video 1 Rename CURSOR MENU CURSOR CURSOR CURSOR

input 2. Use CURSOR  or , then press the SELECT button to change AUTO LINK setting. When AUTO INPUT SIGNAL SENSOR is selected, the TV will turn on and tune to Video2 automatically, when the Video2 input device is turned on. This is convenient when you want to watch a movie with your VCR, laserdisc player, or DVD player. When REMOTE CONTROL SENSOR is selected, the TV will turn on and switch to Video2 automatically when the Video2 input device is turned on and the VCR, laserdisc, or DVD play button on your remote control is pressed. This is convenient when you want to record a movie with your VCR and watch it later. Select Off to disable this function. Press EXIT to quit menu. Video 2 Auto Link NOTES: 1. Once the TV has been turned on using the AUTO LINK feature, it must be reset before AUTO LINK is used again. To do this, turn your VCR, laserdisc, or DVD player OFF. This feature is now reset and will turn on your TV as described above. 2. When using REMOTE CONTROL SENSOR mode, any remote control button will substitute for your video input device play button. However, intended operation is for use with your VCR, laserdisc, or DVD play button. 3. If no remote control button is pressed after the TV is turned on by AUTO LINK, the TV will automatically turn off after three hours. Setup Move SEL Select Set The Inputs Setup Move SEL Return Set The Inputs Video2 Auto Link Auto Input Signal Sensor Remote Control Sensor Off Setup Move SEL Select Set The Inputs Video2 Auto Link Auto Input Signal Sensor Remote Control Sensor Off Video1 Rename Video2 Rename Video2 Auto Link Video3 Rename Video4 Rename Video5 Rename CURSOR CURSOR

week. Use CURSOR  to select Event 1, 2 or 3. Use CURSOR
to change position of On time, Off time, Antenna, Channel, and On/Off Frequency. Use CURSOR  or  to select the time the TV will turn on and off. Use CURSOR  or  to select the day of the week you want the timer to turn on TV. Use number buttons to set the channel the TV will tune to when it automatically turns on. Use CURSOR  or  to select mode Once (TV will turn on/off one time only), Daily (TV will turn on/off at the same time every day), or Weekly-SUN (TV will turn on/off at same time every week). Press EXIT to quit the menu. NOTE: 1. The Off Timer will only activate if the TV was turned on by the On Timer and no channel selection was made after this time. If you change the channel after the On Timer has been activated, the Off Timer will deactivate. 2. If no remote control button is pressed after Event Timer is activated, the TV will automatically turn off after three hours. Therefore, do not Set Event Timer for more than three hours if you do not plan to send a Remote Control I/R to your TV. CAUTION: Do not use your TV as a deterrent when away from home by using the On and Off Timers. For safety, the TV should be turned off when you are away from home. Set Event Timer Set The Channels Set The Clock Menu Preference Setup Set The Inputs Move SEL Select Set Event Timer Set Closed Captions Setup Move SEL Return Set Event Timer Event 1 --:-- AM --:-- AM Ant A Ch -- Once Event 2 --:-- AM --:-- AM Ant A Ch -- Once Event 3 --:-- AM --:-- AM Ant A Ch -- Once Setup Move SEL On/Off Set Event Timer Event 1 --:-- AM --:-- AM Ant A Ch -- Once Event 2 --:-- AM --:-- AM Ant A Ch -- Once Event 3 --:-- AM --:-- AM Ant A Ch -- Once Return About Your TV CURSOR CURSOR Please Set Clock First. If the clock is not set, you can not use this function and the screen below will appear. The message on the screen will disappear after 3 seconds, then the screen automatically goes to the clock setup mode (see page 50).

display on or off. Auto will turn the display on when Mute/Soft Mute is on. Caption Mode: Captions is for the program you are viewing. Text is for additional information such as news reports or a TV program guide. This information covers the entire screen and viewing the TV program is not possible. Text may not be available with every program. CHANNEL: 1 is used for the primary language (usually English). 2 is sometimes used for a second language (may vary by region). 3 is sometimes used for a third language (may vary by region). 4 is sometimes used for a fourth language (may vary by region). Use CURSOR ,  to highlight the function to change then press the SELECT button to change the function. Press EXIT to quit menu or CURSOR  to return to previous menu. Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video which are displayed on the TV screen. Your local TV program guide denotes these programs as or . Closed Caption Setup Move SEL Return Set Closed Caption Caption Display Off On Auto Captions Mode: Captions Text Channel: 1 2 3 4 Set The Channels Set The Clock Menu Preference Setup Set The Inputs Move SEL Select Set Event Timer Set Closed Captions About Your TV CURSOR NOTE: 1. CAPTION DISPLAY will not work when viewing a 480p, 720p, or 1080i input via the COMPONENT: Y-PBPR inputs. 2. When PIP Surf is on, Closed Caption will not work. Setup Move SEL Return About Your TV Model: Dimensions (Inches) (mm) Height: - / - Width: - / - Depth: - / - Set The Channels Set The Clock Menu Preference Setup Set The Inputs Move SEL Select Set Event Timer Set Closed Captions About Your TV CURSOR The TV model name and set dimensions will be displayed on the TV screen. The set dimensions of each TV model are listed on page 60. About Your TV

AND YOUR REMOTE CONTROL DO Dust the screen and cabinet with a soft cloth. Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty. Place your Television away from extreme heat, humidity, and extremely dusty places. Remove the plug from the wall outlet if your Television will not be used for a long period of time, for instances, when you go on vacation. DO NOT Do not clean your screen or cabinet with strong cleaners, polishes or a chemically treated cloth. Do not place rubber or vinyl products or cellophane tape on your Television. Do not touch the screen too often. Do not subject the remote control to shocks such as dropping it on the floor, etc. Physical damage to the precision parts may result. Avoid placing the remote control in a high humidity place or getting it wet. Do not leave it on or near a heater. Excessive heat or moisture may cause the unit to cease operation. When the batteries run down, remote control operation will become erratic or possibly stop altogether. Replace the old batteries with two new “AA” size batteries. Do not use an old battery with a new battery. Exposure of the viewing screen to prolonged direct sunlight or heat may cause the screen to permanently warp, resulting in a distorted picture.

Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. • GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception. Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers. • SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture. • RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture. NOTE: The TV set can generate sound distortion in external devices such as a radio. Please separate radio equipment from the TV set to a considerable distance.

component or circuit damage due to external or internal voltage power surges. IF YOUR TELEVISION SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE: 1. Press the power switch (ON/OFF switch) once. 2. If there is still no power, wait 30 seconds and press the power switch again. 3. If there is still no power, unplug the power cord from the wall. Wait 30 seconds and plug the power cord back in. Press the power switch again. This protective technology should provide for years of lasting entertainment from your HITACHI Projection Television. SYMPTOMS CHECK THESE ITEMS AND TRY THESE ADJUSTMENTS No Picture, no sound Sound OK, picture poor Picture OK, sound poor Picture blurred Lines or streaks in picture Poor reception on some channels Picture rolls vertically No color Poor color                                                      Be sure external connection is correct Be sure power cord is plugged in Be sure TV is switched''ON" Try another channel (station trouble) Check antenna connections (back of TV) Check antenna for broken lead-in wire Check for local interference Check outside antenna Adjust Contrast control Adjust Brightness control Adjust Color control Adjust Tint control Adjust Volume control

• Closed Caption Decoder • 2-Tuner Picture in Picture • Magic Focus (Auto Digital Convergence and Manual Adjustment) • Dual Antenna Inputs • Video Input Sensor • 3 Dimensional Y/C Comb Filter • Full 1080i HDTV capable when used with a Set-Top Box. • High Bandwidth Digital Content Protection V1.0 Compatible. • Technology. • Technology. *SRS and the symbol are registered trademarks of SRS Labs, Inc. SRS technology is incorporated under license from SRS Labs, Inc. *Licensed by BBE Sound, Inc. under USP4638258, 5510752 and 5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc. Manufactured under license from BBE Sound, Inc. Features: • Superfine Picture Quality 1280 Line Horizontal Resolution • Remote (Controls many VCRs, DVD players, cable boxes, and satellite boxes.) • New Easy-to-Use (3-Language) On-Screen Menu • Full Set of Input Jacks, including S-VIDEO • COMPONENT VIDEO: Y-PB/PR Inputs: • Power Input . . . . . . . . . . . . .AC 120V, 60Hz • Stand-by Power . . . . . . . . . . . . . . . . . .1.3W • Power Consumption - Refer to rear panel at the back of the T.V. • Antenna input impedance . . . . . . . . .75 Ohm • Channel coverage . . . . . . . . . . . . . . .181ch. VHF-Band . . . . . . . . . . . . . . . . . . . . .2 ~ 13 UHF-Band . . . . . . . . . . . . . . . . . . . .14 ~ 69 CATV Mid Band . . . . . . . . . . . . . . .A-5 ~ A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . .A-I Super Band . . . . . . . . . . . . . . . . . . . . .J-W Hyper Band . . . . . . . . . . . . . . .W+1 - W+28 Ultra Band . . . . . . . . . . . . . . .W+29 - W+84 • Video . . . . . . . . . . . . . . . .1.0Vp-p, 75 Ohm • S-Video Luminance (Y) . . . . . . . . . .1.0Vp-p, 75 Ohm Chrominance (C) . . . . . .0.286Vp-p, 75 Ohm • Component Video Luminance (Y) . . . . . . . . . . . . . . .1.0Vp-p, 75 Ohm Chrominance (PB/PR) . . . . . . . . .0.7Vp-p, 75 Ohm • Audio input Impedence . . . . . . . . . .47k Ohm • Average input level . . . . . . . . . . . . . . . .470mVrms • DVI-HDTV . . . . . . . . . . . . . . . . . . . . . . .DVI 25 pin Outputs: • Video . . . . . . . . . . . . . . . . . . . . .1.0Vp-p. 75 Ohm • Audio (Fixed) . . . . . . . . . . . . .470mVrms, 1k Ohm Dimensions: 43FWX20B 51GWX20B 57GWX20B 51UWX20B 57UWX20B • Height (in.) 39 50 1/8 54 3/16 (mm) 989.90 1,273.5 1,376.2 • Width (in.) 41 1/4 48 12/16 54 (mm) 1,047.0 1,239.0 1,372.0 • Depth (in.) 20 5/8 25 1/16 25 8/16 (mm) 523.90 636.0 647.9 • Weight (lbs.) 153 238 265 NOTE: Due to improvements, specifications in this oper- ating guide are subject to change without notice.

Home Electronics Division 1855 Dornoch Court San Diego, CA 92154 Hitachi America, LTD. Home Electronics Division Hitachi has made every effort to assure you hours of trouble free operation from your unit. However, should you require service, a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico. Each facility will provide you with convenient and expedient assistance. Our service hotline operator will direct you to the Hitachi Authorized Service Facility nearest you. Just present proof of purchase and/or delivery receipts to the Hitachi Authorized Service Facility, and serv- ice will be rendered in accordance with the terms of the limited warranty as stated on your warranty card or operating guide. Should you have any questions regarding warranty, service, operation, or technical assistance, please con- tact: service service To locate an authorized HITACHI service facility in the continental U.S.A. and Canada, DIAL TOLL FREE 7 days a week, 24 hours a day 800 HITACHI 800 HITACHI (1-800-448-2244)

Saturday EST 9:00am - 5:00pm Hitachi Canada, LTD. Digital Media Division Should you have any questions regarding warranty, service, operation, or technical assistance, please contact: Look for your French Manual on the outside of the box. If the manual is missing, call for a copy. 1-800-HITACHI (1-800-448-2244) Au Canada: 1-800-HITACHI (1-800-448-2244) Lundi - Vendredi L’EST 9:00am - 7:00pm Samedi L’EST 9:00am - 5:00pm Pour de plus amples renseignements sur le service durant la période couverte par la garantie, sur le fonc- tionnement ou pour de l’assistance technique communiquez avec: La version français de votre manual se trouve a l’exterieur de la boîte. Si le manuel est manquant, coposez le pour obenir votre copie. 1-800-HITACHI (1-800-448-2244) HITACHI CANADA, LTD. 6740 Campobello Road Mississauga, ON L5N 2L8