Hitachi C 9SA2 Technical And Service Manual

LIST Nos. C 9SA2: E516 C 9BA2: E517 Nov. 2006 C MODELS C 9SA2 C 9BA2 Hitachi
Power Tools

is(are) used in the place of company name(s) and model name(s) of our competitor(s). The symbol(s) utilized here is(are) as follows: Symbol Utilized Competitor Company Name Model Name B BOSCH GKS85S C MAKITA 5900B C 9SA2, C 9BA2

2. MARKETING OBJECTIVE .............................................................................................................1 3. APPLICATIONS ..............................................................................................................................1 4. SELLING POINTS ..........................................................................................................................2 4-1. Selling Point Descriptions .............................................................................................................. 3 5. SPECIFICATIONS ..........................................................................................................................5 6. COMPARISONS WITH SIMILAR PRODUCTS ..............................................................................6 7. PRECAUTIONS IN SALES PROMOTION .....................................................................................7 7-1. Handling Instructions ..................................................................................................................... 7 7-2. Caution on Name Plate.................................................................................................................. 7 8. PRECAUTIONS IN DISASSEMBLY AND REASSEMBLY ............................................................8 8-1. Disassembly .................................................................................................................................. 8 8-2. Reassembly ................................................................................................................................... 9 8-3. Insulation Tests ............................................................................................................................ 12 8-4. Cleaning the Cover ...................................................................................................................... 12 9. STANDARD REPAIR TIME (UNIT) SCHEDULES .......................................................................13 Assembly Diagram for C 9SA2 Assembly Diagram for C 9BA2

1. PRODUCT NAME Hitachi Circular Saws, Models C 9SA2/C 9BA2 [235 mm (9-1/4")] 2. MARKETING OBJECTIVE Fifteen years have passed since the sales start of the Model C 9. Although this model has been well reputed in the market thanks to the ease of operation, compact and lightweight body until now, it is upgraded to the new Models C 9SA2 and C 9BA2. With these new models, we aim to expand our market share. The key features of the new models are as follows: (1) Compact and lightweight (2) Unique design (3) Low noise and vibration (4) Electric brake (Model C 9BA2 only) (5) PTFE coating base for smooth sliding of workpieces (Model C 9BA2 only) 3. APPLICATIONS Cutting of various wood materials

4. SELLING POINTS Large knob for easy cutting depth adjustment Low noise and vibration (Noise level during no-load operation: 3 dB lower than the conventional model) Main handle Blower function to blow out cutting dust on the ink line Precise and heavy-duty aluminum die-cast base and lower guard Comfortable and nonskid soft-touch handle Main handle Adjustable steel guide piece Powerful motor Unique design Electric brake (Model C 9BA2 only) Most lightweight in the class thanks to the gear cover made of die-cast magnesium alloy PTFE coating base for smooth sliding of workpieces (Model C 9BA2 only) Compact and lightweight (Weight: 6.8 kg)

4-1. Selling Point Descriptions (1) Compact and lightweight Catalog weight Maker Model * Measured weight kg kg HITACHI C 9SA2 B HITACHI C 9BA2 C 6.8 6.8 6.9 7.3 6.8 6.8 7.0 7.0 The Models C 9SA2 and C 9BA2 are most lightweight in each category as shown in Table 1. (2) Unique design Ease of operation is sufficiently considered in designing the Models C 9SA2 and C 9BA2 including the handle location and shape. These models are uniquely designed through the richly used elastomer. The elastomer used at the handle makes each model easier to operate. (3) Low noise and vibration In the Models C 9SA2 and C 9BA2, the ball bearings at the front and the back of the motor are supported by rubber parts and a highly efficient, low-noise and small-diameter fan is adopted. The noise level and the vibration level at start-up and no-load operation are reduced thanks to the above. (4) Electric brake (Model C 9BA2 only) The Model C 9BA2 is equipped with the electric brake function that is well-reputed in the conventional model. The rotation of the motor is braked upon turning off the switch and stopped in a shorter time than the case of a circular saw without braking function. Thus the Model C 9BA2 can quickly start the next work. (5) PTFE coating base for smooth sliding of workpieces (Model C 9BA2 only) When the operator pushes the circular saw forward during cutting, the pushing force is partially compensated by friction with the workpiece. The PTFE coating base can reduce such a compensated force because the frictional resistance is low. As a result, workpieces can be cut smoothly. (6) Powerful motor Table 2. Comparison of power input/measured weight ratio when using 9" dia. saw blade Table 1. 9" circular saw weight comparisons (* Measured weight excludes cord, guide and saw blade) Power input * Measured weight W kg HITACHI C 9SA2 B HITACHI C 9BA2 C 2000 6.8 1700 7.3 2000 6.8 2000 7.0 Input/ weight W/kg 299 233 299 286 The Models C 9SA2 and C 9BA2 are superior to competitors concerning power input values in each category as shown in Table 2. The power input/measured weight ratio obtained by dividing the power input by the measured weight is also superior to competitors. The Models C 9SA2 and C 9BA2 are well-balanced circular saws. Maker Model

(7) Comfortable and nonskid soft-touch handle The handle is entirely covered with elastomer. The main handle and the sub handle are nonskid and fit in hands for comfortable cutting operation. (8) Adjustable steel guide piece If the center of the saw blade is deviated from the notch of the guide piece due to continuous operation or replacement of the saw blade, the position of the guide piece can be adjusted finely for more accurate cutting operation. It is also convenient for cutting with respect to either side of the blade. The guide piece is made of steel for higher strength. (9) Blower function to blow out cutting dust on the ink line The conventional models discharge almost all the cooling air forward as a blower function. However, discharge of cooling air increases the operating noise. To cope with this, the Models C 9SA2 and C 9BA2 are equipped with the improved cooling air path to reduce the operating noise while maintaining the blower function. (10) Precise and heavy-duty aluminum die-cast base and lower guard The base and the lower guard are made of heavy-duty aluminum die-cast material. The Models C 9SA2 and C 9BA2 can accurately cut workpieces for a long time because the base and the lower guard are highly durable and resistant to warping. (11) Large knob for easy cutting depth adjustment The large knob is easy to adjust cutting depth speedily and reliably. (12) Gear cover made of die-cast magnesium alloy The Models C 9SA2 and C 9BA2 are most lightweight in the class thanks to the gear cover made of die-cast magnesium alloy.

* Be sure to check the name plate on product as it is subject to change by areas. ** Measured weight excludes cord, guide and saw blade. Housing Handle cover Gear cover Saw cover Lower guard Base Polycarbonate resin, elastomer Polycarbonate resin, elastomer Die-cast magnesium alloy Polycarbonate resin, elastomer Die-cast aluminum alloy Die-cast aluminum alloy Standard accessories Tungsten carbide tipped (TCT) saw blade • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 1 Hex. bar wrench ....................................................................................... 1 Guide .........................................................................................................1 Wing bolt....................................................................................................1 Type of motor Enclosure Weight AC single phase Cutting depth at 90û Power source * Power input at 45û Voltage (V) * Current (A) Rotation speed Cord No-load Gross (with case) ** Net Full-load Type Overall length 1,570 W 2,600 min-1 2.5 m (8.2 ft.) 5. SPECIFICATIONS 235 mm (9-1/4") Two-core cabtire cable Model Saw blade diameter C 9SA2 0 to 86 mm (0 to 3-3/8") AC single phase commutator motor Packing Corrugated cardboard box/Plastic case and corrugated cardboard sleeve Max. 65 mm (2-9/16") Type of switch Trigger switch 6.8 kg (15.0 lbs) 11.5 kg (25.4 lbs) 110 15 5,000 min-1 3,200 min-1 C 9BA2 Gross 9.0 kg (19.8 lbs) Long guide .................................................................................................1 Dust collector ............................................................................................ 1 Lever (Short type) ......................................................................................1 Optional accessories 220 9.6 2,000 W 230 9.2 2,000 W 240 8.8 2,000 W 3,360 min-1

Maker Model Power input No-load rotation speed Overall length Weight No-load rotation speed Full-load rotation speed Full-load output Max. output No-load noise Max. cutting depth 90 45 mm (in.) mm (in.) mm (in.) W min-1 mm kg (lbs.) min-1 min-1 W W dB Saw blade diameter Catalog specifications Characteristics Structure HITACHI HITACHI B C C 9BA2 C 9SA2 C 9 235 (9-1/4") 86 (3-3/8") 65 (2-9/16") 2000 5000 397 6.8 (15.0) 5040 3360 1260 3220 86 235 (9-1/4") 86 (3-3/8") 65 (2-9/16") 1750 4900 376 7.1 (15.7) 4630 3220 1160 2900 90 230 (9-3/64") 85 (3-11/32") 60 (1-23/64") 1700 4000 395 6.9 (15.2) 4700 3180 1370 3020 92 235 (9-1/4") 86 (3-3/8") 65 (2-9/16") 2000 5000 397 6.8 (15.0) 5190 3252 1300 2960 86 235 (9-1/4") 85 (3-11/32") 64 (2-33/64") 2000 4500 400 7.0 (15.4) 4720 3800 980 3930 91 L H W mm mm mm Nickel plated aluminum Aluminum Provided Provided 397 291 272 Material of lower guard Soft-touch handle Blower function Material of base Nickel plated aluminum Aluminum None None 376 288 257 Steel Aluminum None None 395 315 377 PTFE plated aluminum Aluminum Provided Provided 397 291 272 Aluminum Aluminum None None 400 276 271 6. COMPARISONS WITH SIMILAR PRODUCTS

7. PRECAUTIONS IN SALES PROMOTION In the interest of promoting the safest and most efficient use of the Models C 9SA2 and C 9BA2 Circular Saws by all of our customers, it is very important that at the time of sale the salesperson carefully ensures that the buyer seriously recognizes the importance of the contents of the Handling Instructions. 7-1. Handling Instructions Although every effort is made in each step of design, manufacture, and inspection to provide protection against safety hazards, the dangers inherent in the use of any electric tool cannot be completely eliminated. Accordingly, general precautions and suggestions for the use of electric power tools, and specific precautions and suggestions for the use of the circular saw are listed in the Handling Instructions to enhance the safe and efficient use of the tool by the customer. Salespersons must be thoroughly familiar with the contents of the Handling Instructions to be able to offer appropriate guidance to the customer during sales promotion. 7-2. Caution on Name Plate Each tool is provided with a Name Plate which contains the following basic safety precautions in the use of the tool. (1) For New Zealand and Australia CAUTION Read thoroughly HANDLING INSTRUCTIONS before use.

8. PRECAUTIONS IN DISASSEMBLY AND REASSEMBLY The disassembly and reassembly procedures for the Models C 9SA2 and C 9BA2 are essentially the same. The [Bold] numbers in the descriptions below correspond to the item numbers in the parts list and exploded assembly diagram for the Model C 9SA2. During disassembly and reassembly, and at all other times as well, sufficient care must be exercised in handling to ensure that there is no deviation in the flatness of the bottom surface of the base and in its perpendicularity with relation to the saw blade. 8-1. Disassembly (1) Prior to attempting further disassembly, ensure without fail that the TCT Saw Blade 235MM [12] is removed to prevent damage to its cutting edge, and to avoid possible serious accident. (2) Removal of the Safety Cover [7] First, disconnect the Return Spring [8] from the Safety Cover [7]. Then, loosen the two Seal Lock Flat Hd. Screws M5 x 14 [10] and take off the Bearing Cover [9]. The Safety Cover [7] can then be removed. Fig. 1 (5) Removal of the Armature [24] First, remove the Brush Caps [58] and take out the Carbon Brushes (1 Pair) [57]. Then, loosen the Machine Screws (W/Washers) M5 x 40 (Black) [59] and separate the Housing Ass'y [62] from the Gear Cover [27]. If the Armature [24] is remained in the Housing Ass'y [62], gently tap the Housing Ass'y [62] on the edge of the surface where the Gear Cover [27] is mounted with a wooden or plastic hammer and remove the Armature [24]. At this time, be very careful not to hit the fan on the Armature [24]. If the Bearing Bushing [31] is remained in the Housing Ass'y [62], remove it in the same manner as the case of the Armature [24]. If the Rubber Bushing [30] is remained in the Housing Ass'y [62], remove it with tweezers being very careful not to scratch it. (6) Removal of the Base Ass'y [45] Extract the Roll Pin D8 x 50 [26] and disassemble the Base Ass'y [45] from the Gear Cover [27]. (3) Removal of the Bearing Holder [3] together with the Spindle and Gear Set [2] After removing the Safety Cover [7] as described above, loosen the two Seal Lock Flat Hd. Screws M6 x 14 [4]. (4) Separation of the Spindle and Gear Set [2] from the Bearing Holder [3] As illustrated in Fig. 1, support the Bearing Holder [3] with an appropriate tubular jig, and push down on the end of the spindle to separate the Spindle and Gear Set [2] from the Bearing Holder [3]. Jig Push 56 mm (2-13/64") 60 mm (2-23/64")

Fig. 2 (2) Reassembling the Stator Ass'y [22] To align each screw hole of the Stator Ass'y [22] and the Housing Ass'y [62] accurately, insert the guide bar (J-132 stator press pins [special repair tool, code no. 970911] are recommended) to press-fit the Stator Ass'y [22] to the Housing Ass'y [62] as shown in Fig. 2. After press-fitting, hook the Brush Terminal [21] on the Brush Holder [56]. Be careful not to pinch the internal wire of the Stator Ass'y [22] between the Stator Ass'y [22] and the seat for the Hex. Hd. Tapping Screw D5 x 65 [33] in the Housing Ass'y [62]. Secure the Stator Ass'y [22] to the Housing Ass'y [62] with the two Hex. Hd. Tapping Screws D5 x 65 [33]. (3) Reassembly of the Armature [24] Prior to assembling the Armature [24], ensure that the Rubber Ring [35] is properly inserted into the groove of the bearing case within the Gear Cover [27]. At this time, be very careful not to damage the Rubber Ring [35]. Be sure to mount the Bearing Bushing [31] and the Rubber Bushing [30] to the Armature [24] before reassembly. Do not perform reassembly with the Bearing Bushing [31] and the Rubber Bushing [30] remained in the Housing Ass'y [62]. [22] [55] [21] 8-2. Reassembly Reassembly can be accomplished by following the disassembly procedures in reverse. However, particular attention should be given to the following items. (1) Tightening torques for fastening screws and bolts Machine Screws M4 [17] [20] [46] ........................................... 1.8 0.4 N•m {18 4 kgf•cm} Special Bolt [15] ....................................................................... 1.8 0.4 N•m {18 4 kgf•cm} Machine Screws M5 [59] .......................................................... 3.4 0.7 N•m {35 7 kgf•cm} Seal Lock Flat Hd. Screw M6 x 14 [4] ...................................... 4.9 1.0 N•m {50 10 kgf•cm} Hex. Socket Hd. Bolt M8 x 15.5 [19] ........................................ 14.7 1.0 N•m {150 10 kgf•cm} Tapping Screws (W/Flange) D4 [60] [66] [73].......................... 2.0 0.5 N•m {20 5 kgf•cm} Hex. Hd. Tapping Screw D5 x 65 [33] ...................................... 2.9 0.5 N•m {30 5 kgf•cm} Screw of switches ..................................................................... 0.8 0.2 N•m {8 2 kgf•cm} Screw of pillar terminal ............................................................. 0.35 0.1 N•m {3.5 1 kgf•cm} Guide bar (J-132 stator press pins) Name plate side [21]

(5) Lubrication Literally apply the designated lubricants as follows: Within the Gear Cover [27]................................................. Grease (SEP-3A) Code No. 930035 9 g Apply the above grease to the pinion teeth of the Armature [24] entirely. (6) Internal wire arrangement Connect internal wire as illustrated in Fig. 4 to Fig. 5. At this time, ensure that none of the wires are pinched between components during assembly. (4) Reassembly of the Lock Lever [25] (See Fig. 3.) A. Position the Lock Lever [25] between the fan and the Ball Bearing 6202VVCMPS2L [34] of the Armature [24], and carefully assemble it together with the Armature [24] into the Gear Cover [27]. B. Ensure that both ends of the spring on the Lock Lever [25] are properly supported inside the ribs of the Gear Cover [27]. C. When assembly of the Lock Lever [25] is completed (when the Gear Cover [27] has been assembled to the Housing Ass'y [62] and fastening with the Machine Screws (W/Washers) M5 x 40 (Black) [59]), push the Lock Lever [25] by hand and ensure that it returns to its original position when released. Fig. 3 [27] [27] [25] Spring Rib

Fig. 4 Fig. 5 A. Model C 9SA2 Safety lock button (Only for New Zealand and Australia) B. Model C 9BA2 Noise suppressor (Only for New Zealand, Australia, Korea and Taiwan) Blue or white lead wires Pillar terminal Blue or white Brown White Blue Pillar terminal Terminal White Cord Noise suppressor Armature Stator coil Stator coil Switch Stator Switch Safety lock button (Only for Australia) Noise suppressor (Only for Australia and Taiwan) Blue, black and yellow lead wires Pillar terminal Black Brown White Blue Pillar terminal Terminal White Cord Noise suppressor Stator coil Brake coil Switch Armature Switch Blue Yellow Blue or white

8-3. Insulation Tests On completion of disassembly and repair, measure the insulation resistance and conduct dielectric strength test. Insulation resistance: 7 M Ω or more with DC 500 V megohm tester Dielectric strength: AC 4000 V/1 minute, with no abnormalities 8-4. Cleaning the Cover Clean the exterior of the tool with a soft cloth moistened with soapy water, and dry thoroughly. Chloric solvent, gasoline, and thinner will cause plastic components to dissolve.

9. STANDARD REPAIR TIME (UNIT) SCHEDULES MODEL 10 20 30 40 Fixed Variable Work Flow Switch Cord Cord Armor Armature Ass'y Ball Bearing (6202VV) Ball Bearing (6000VV) Bearing Bushing Protective Cover Return Spring Saw Cover 60 min. 50 Housing Ass'y Stator Ass'y Spindle and Gear Set Bearing Holder Ball Bearing (6203VV) Gear Cover Base Ass'y General Assembly C 9SA2 Handle Cover C 9BA2

LIST NO. E516 CIRCULAR SAW Model C 9SA2 2006 • 11 • 16 (E1) Hitachi Power Tools A A B B 1 2 3 4 5 6 7 8 9 10 11 19 23 15 63 64 39 13 14 12 16 17 18 20 21 22 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 59 60 56 57 58 61 65 66 67 68 62 70 71 72 73 69 74 75 76 505 501 502 503 504

--- 2 --- ITEM NO. CODE NO. DESCRIPTION REMARKS NO. USED PARTS 11 -- 06 C 9SA2 1 673-002 NEEDLE BEARING (HK1212) 1 2 303-789 SPINDLE AND GEAR SET 1 3 303-790 BEARING HOLDER 1 4 303-797 SEAL LOCK FLAT HD. SCREW M6X14 2 5 998-887 LINER 1 6 620-3VV BALL BEARING 6203VVCMPS2L 1 7 326-803 SAFETY COVER 1 8 303-906 RETURN SPRING 1 9 303-804 BEARING COVER 1 10 992-013 SEAL LOCK FLAT HD. SCREW M5X14 2 * 11 326-802 WASHER (A) 1 * 11 303-365 WASHER (A) 1 FOR AUS, NZL * 12 326-830 TCT SAW BLADE 235MM-D25.4 HOLE-NT40 1 * 12 326-829 TCT SAW BLADE 235MM-D25 HOLE-NT40 1 FOR AUS, NZL 13 325-354 SAW COVER 1 14 HITACHI LABEL 1 15 324-139 SPECIAL BOLT 1 16 302-464 KNOB 1 17 304-043 MACHINE SCREW (W/WASHERS) M4X10 (BLACK) 1 18 302-423 WASHER (B) 1 19 324-662 HEX. SOCKET HD. BOLT M8X15.5 1 20 305-691 MACHINE SCREW (W/WASHERS) M4X14 (BLACK) 4 21 937-623 BRUSH TERMINAL 2 * 22 340-691C STATOR ASS’Y 110V 1 INCLUD. 21 * 22 340-660P STATOR ASS’Y 110V 1 INCLUD. 21 FOR TPE * 22 340-691E STATOR ASS’Y 220V-230V 1 INCLUD. 21 * 22 340-660Q STATOR ASS’Y 220V-230V 1 INCLUD. 21 FOR NZL, KOR * 22 340-691F STATOR ASS’Y 240V 1 INCLUD. 21 * 22 340-660R STATOR ASS’Y 240V 1 INCLUD. 21 FOR AUS 23 325-352 FAN GUIDE 1 * 24 360-759C ARMATURE 110V 1 * 24 360-759E ARMATURE 220V-230V 1 * 24 360-759F ARMATURE 240V 1 25 303-793 LOCK LEVER 1 26 949-884 ROLL PIN D8X50 (10 PCS.) 1 27 325-350 GEAR COVER 1 INCLUD. 1, 28, 29, 35 28 961-729 CUSHION 1 29 949-794 FLAT HD. SCREW M6X20 (10 PCS.) 1 30 325-356 RUBBER BUSHING 1 31 325-355 BEARING BUSHING 1 32 600-0VV BALL BEARING 6000VVCMPS2L 1 33 960-251 HEX. HD. TAPPING SCREW D5X65 2 34 620-2VV BALL BEARING 6202VVCMPS2L 1 35 303-792 RUBBER RING 1 36 324-660 KNOB 1 37 676-531 O-RING (P-7) 1 38 303-801 SLEEVE 1 39 961-436 WASHER (B) 1 40 324-658 WING NUT M8 1 41 949-433 BOLT WASHER M8 (10 PCS.) 1 42 301-806 WING BOLT M6X15 1

--- 3 --- ITEM NO. CODE NO. DESCRIPTION REMARKS NO. USED PARTS 11 -- 06 C 9SA2 43 947-859 LOCK SPRING 1 44 302-469 SLOTTED HD. SET SCREW (SEAL LOCK) M6X6 1 45 326-804 BASE ASS’Y 1 INCLUD. 40, 41, 46-51, 53, 54 46 317-333 MACHINE SCREW (W/SP. WASHER) M4X6 1 47 324-659 GUIDE PIECE 1 48 302-457 BOLT (SQUARE) M8X30 1 49 308-481 BEVEL PLATE 1 50 308-482 RIVET D6X24 1 51 308-480 RIVET D6X17 1 52 303-800 DIAGONAL BOLT M8 1 53 949-425 WASHER M6 (10 PCS.) 1 54 302-438 WING BOLT (A) M6X20 1 55 938-477 HEX. SOCKET SET SCREW M5X8 2 56 983-362 BRUSH HOLDER 2 57 999-038 CARBON BRUSH (1 PAIR) 2 58 961-781 BRUSH CAP 2 59 303-796 MACHINE SCREW (W/WASHERS) M5X40 (BLACK) 3 60 301-653 TAPPING SCREW (W/FLANGE) D4X20 (BLACK) 5 61 NAME PLATE 1 * 62 325-363 HOUSING ASS’Y 1 INCLUD. 55, 56 * 62 325-362 HOUSING ASS’Y 1 INCLUD. 55, 56 FOR AUS, NZL * 63 325-358 SAFETY LOCK BUTTON 1 FOR AUS, NZL * 64 325-359 SPRING 1 FOR AUS, NZL 65 325-357 SWITCH (1P SCREW TYPE) 1 66 305-720 TAPPING SCREW (W/FLANGE) D4X12 1 67 946-362 BEARING LOCK 1 68 325-351 HANDLE COVER 1 * 69 980-063 TERMINAL 1 FOR AUS, NZL, TPE, KOR 70 938-307 PILLAR TERMINAL 1 * 71 980-063 TERMINAL 1 FOR CORD * 71 930-804 TERMINAL M4.0 (10 PCS.) 1 FOR CORD FOR TPE 72 937-631 CORD CLIP 1 73 984-750 TAPPING SCREW (W/FLANGE) D4X16 2 * 74 930-039 NOISE SUPPRESSOR 1 FOR AUS, NZL, TPE, KOR * 75 958-049 CORD ARMOR D8.2 1 * 75 940-778 CORD ARMOR D10.7 1 * 76 500-234Z CORD 1 (CORD ARMOR D8.2) * 76 500-423Z CORD 1 (CORD ARMOR D8.2) FOR SIN, KUW * 76 500-439Z CORD 1 (CORD ARMOR D8.2) FOR AUS, NZL * 76 500-447Z CORD 1 (CORD ARMOR D8.2) FOR SYR * 76 500-435Z CORD 1 (CORD ARMOR D8.2) FOR HKG * 76 500-474Z CORD 1 (CORD ARMOR D10.7) FOR TPE * 76 500-455Z CORD 1 (CORD ARMOR D8.2) FOR THA * 76 500-214Z CORD 1 (CORD ARMOR D10.7) FOR VEN

--- 4 --- 11 -- 06 OPTIONAL ACCESSORIES ITEM NO. CODE NO. DESCRIPTION REMARKS NO. USED STANDARD ACCESSORIES ITEM NO. CODE NO. DESCRIPTION REMARKS NO. USED C 9SA2 Printed in Japan (061116N) 501 303-888 GUIDE 1 502 872-422 HEX. BAR WRENCH 6MM 1 503 303-811 SIDE HANDLE 1 504 949-340 FLAT HD. SCREW M6X16 (10 PCS.) 2 * 505 325-364 CASE 1 FOR AUS, NZL 601 325-365 LONG GUIDE 1 602 324-669 DUST COLLECTOR 1 603 303-338 KNOB 1

LIST NO. E517 CIRCULAR SAW Model C 9BA2 2006 • 11 • 16 (E1) Hitachi Power Tools A A B B 16 1 2 3 4 5 6 7 8 9 10 11 20 15 24 64 65 40 13 14 12 17 18 19 21 22 23 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 60 61 57 58 59 62 66 67 68 69 63 71 72 73 74 70 75 76 77 505 501 502 503 504

--- 2 --- ITEM NO. CODE NO. DESCRIPTION REMARKS NO. USED PARTS 11 -- 06 C 9BA2 1 673-002 NEEDLE BEARING (HK1212) 1 2 303-789 SPINDLE AND GEAR SET 1 3 303-790 BEARING HOLDER 1 4 303-797 SEAL LOCK FLAT HD. SCREW M6X14 2 5 998-887 LINER 1 6 620-3VV BALL BEARING 6203VVCMPS2L 1 7 326-803 SAFETY COVER 1 8 303-906 RETURN SPRING 1 9 303-804 BEARING COVER 1 10 992-013 SEAL LOCK FLAT HD. SCREW M5X14 2 * 11 326-802 WASHER (A) 1 * 11 303-365 WASHER (A) 1 FOR AUS, NZL * 12 326-830 TCT SAW BLADE 235MM-D25.4 HOLE-NT40 1 * 12 326-829 TCT SAW BLADE 235MM-D25 HOLE-NT40 1 FOR AUS, NZL 13 325-354 SAW COVER 1 14 HITACHI LABEL 1 15 NAME PLATE (BRAKE) 1 16 324-139 SPECIAL BOLT 1 17 302-464 KNOB 1 18 304-043 MACHINE SCREW (W/WASHERS) M4X10 (BLACK) 1 19 302-423 WASHER (B) 1 20 324-662 HEX. SOCKET HD. BOLT M8X15.5 1 21 305-691 MACHINE SCREW (W/WASHERS) M4X14 (BLACK) 4 22 937-623 BRUSH TERMINAL 1 * 23 340-692C STATOR ASS’Y 110V 1 INCLUD. 22 * 23 340-661C STATOR ASS’Y 110V 1 INCLUD. 22 FOR TPE * 23 340-692E STATOR ASS’Y 220V-230V 1 INCLUD. 22 * 23 340-692F STATOR ASS’Y 240V 1 INCLUD. 22 * 23 340-661F STATOR ASS’Y 240V 1 INCLUD. 22 FOR AUS, NZL 24 325-352 FAN GUIDE 1 * 25 360-778C ARMATURE 110V 1 * 25 360-778E ARMATURE 230V 1 * 25 360-778F ARMATURE 240V 1 26 303-793 LOCK LEVER 1 27 949-884 ROLL PIN D8X50 (10 PCS.) 1 28 325-350 GEAR COVER 1 INCLUD. 1, 29, 30, 36 29 961-729 CUSHION 1 30 949-794 FLAT HD. SCREW M6X20 (10 PCS.) 1 31 325-356 RUBBER BUSHING 1 32 325-355 BEARING BUSHING 1 33 600-0VV BALL BEARING 6000VVCMPS2L 1 34 960-251 HEX. HD. TAPPING SCREW D5X65 2 35 620-2VV BALL BEARING 6202VVCMPS2L 1 36 303-792 RUBBER RING 1 37 324-660 KNOB 1 38 676-531 O-RING (P-7) 1 39 303-801 SLEEVE 1 40 961-436 WASHER (B) 1 41 324-658 WING NUT M8 1 42 949-433 BOLT WASHER M8 (10 PCS.) 1 43 301-806 WING BOLT M6X15 1

--- 3 --- ITEM NO. CODE NO. DESCRIPTION REMARKS NO. USED PARTS 11 -- 06 C 9BA2 44 947-859 LOCK SPRING 1 45 302-469 SLOTTED HD. SET SCREW (SEAL LOCK) M6X6 1 46 326-805 BASE ASS’Y 1 INCLUD. 41, 42, 47-52, 54, 55 47 317-333 MACHINE SCREW (W/SP. WASHER) M4X6 1 48 324-659 GUIDE PIECE 1 49 302-457 BOLT (SQUARE) M8X30 1 50 308-481 BEVEL PLATE 1 51 308-482 RIVET D6X24 1 52 308-480 RIVET D6X17 1 53 303-800 DIAGONAL BOLT M8 1 54 949-425 WASHER M6 (10 PCS.) 1 55 302-438 WING BOLT (A) M6X20 1 56 938-477 HEX. SOCKET SET SCREW M5X8 2 57 983-362 BRUSH HOLDER 2 58 999-038 CARBON BRUSH (1 PAIR) 2 59 961-781 BRUSH CAP 2 60 303-796 MACHINE SCREW (W/WASHERS) M5X40 (BLACK) 3 61 301-653 TAPPING SCREW (W/FLANGE) D4X20 (BLACK) 5 62 NAME PLATE 1 * 63 325-363 HOUSING ASS’Y 1 INCLUD. 56, 57 * 63 325-362 HOUSING ASS’Y 1 INCLUD. 56, 57 FOR AUS, NZL * 64 325-358 SAFETY LOCK BUTTON 1 FOR AUS, NZL * 65 325-359 SPRING 1 FOR AUS, NZL 66 325-357 SWITCH (1P SCREW TYPE) 1 67 305-720 TAPPING SCREW (W/FLANGE) D4X12 1 68 946-362 BEARING LOCK 1 69 325-351 HANDLE COVER 1 * 70 980-063 TERMINAL 1 FOR AUS, NZL, TPE 71 938-307 PILLAR TERMINAL 1 * 72 980-063 TERMINAL 1 FOR CORD * 72 930-804 TERMINAL M4.0 (10 PCS.) 1 FOR CORD FOR TPE 73 937-631 CORD CLIP 1 74 984-750 TAPPING SCREW (W/FLANGE) D4X16 2 * 75 930-039 NOISE SUPPRESSOR 1 FOR AUS, NZL, TPE * 76 958-049 CORD ARMOR D8.2 1 * 76 940-778 CORD ARMOR D10.7 1 * 77 500-234Z CORD 1 (CORD ARMOR D8.2) * 77 500-423Z CORD 1 (CORD ARMOR D8.2) FOR SIN, KUW * 77 500-439Z CORD 1 (CORD ARMOR D8.2) FOR AUS, NZL * 77 500-447Z CORD 1 (CORD ARMOR D8.2) FOR SYR * 77 500-461Z CORD 1 (CORD ARMOR D8.2) FOR HKG * 77 500-474Z CORD 1 (CORD ARMOR D10.7) FOR TPE * 77 500-214Z CORD 1 (CORD ARMOR D10.7) FOR VEN

--- 4 --- 11 -- 06 OPTIONAL ACCESSORIES ITEM NO. CODE NO. DESCRIPTION REMARKS NO. USED STANDARD ACCESSORIES ITEM NO. CODE NO. DESCRIPTION REMARKS NO. USED C 9BA2 Printed in Japan (061116N) 501 303-888 GUIDE 1 502 872-422 HEX. BAR WRENCH 6MM 1 503 303-811 SIDE HANDLE 1 504 949-340 FLAT HD. SCREW M6X16 (10 PCS.) 2 * 505 325-364 CASE 1 FOR AUS, NZL 601 325-365 LONG GUIDE 1 602 324-669 DUST COLLECTOR 1 603 303-338 KNOB 1