Honda 08E91-E54-100 Installation Insructions

AII 50024-50373 (1308) 1 of 25 08E92-T0A-1B00-90 AII 50024-50373 REMOTE CONTROL ENGINE STARTER 2014 CR-V AUG 2013 PARTS LIST Remote Control Engine Starter Kit P/N 08E91-E54-100 Transmitter Control unit Antenna ID label Remote Control Engine Starter Attachment Kit P/N 08E92-T0A-100B Control unit bracket Engine starter harness 3 Relays 20 Cable ties Long Cable tie 6 Urethane tapes Clip Caution label Fuse label Accessory User’s Information Manual

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. Quick Start Guide TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Diagonal cutters Ratchet 8 mm, 10 mm, and 12 mm Sockets 10 mm Open end wrench Isopropyl alcohol Scissors Shop towel Ruler Tape measure HDS/MVCI Electrical tape Felt-tip pen Tape Masking tape The following tools are available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857. • Trim Tool Set (T/N SOJATP2014) • Plastic Trim Tool (T/N SILTRIMTL10) Illustration of the Remote Control Engine Starter Installed on the Vehicle QC50901AB 40A FUSE CONTROL UNIT ANTENNA 3 RELAYS 3A FUSE ENGINE STARTER HARNESS INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” NOTE: This antenna should only be installed if the ambient air temperature is 15°C (60°F) or above. 1. Move the driver’s seat all the way back. 2. Disconnect the negative cable from the battery. 3. Attach the ID label. • Using isopropyl alcohol on a shop towel, clean the area where the ID label will attach. • Attach the ID label to the transmitter in the area as shown. QBD0601AE ID LABEL TRANSMITTER Clean with isopropyl alcohol.

AII 50024-50373 (1308) 3 of 25 Removing the Vehicle Parts 4. Remove the roof console. • Using a plastic trim tool, pry off the left and right lenses. • Open the sunglass holder and remove the screws. • Remove the roof console and unplug the vehicle connectors. Q0N2012AG VEHICLE CONNECTORS ROOF CONSOLE 4 SCREWS 4 RETAINING TABS LEFT LENS SUNGLASS HOLDER (Open.) 4 RETAINING TABS RIGHT LENS 5. Release the driver’s sunvisor from the sunvisor holder. Rotate the holder 45° counterclockwise and remove it QC50902AB Rotate. SUNVISOR HOLDER SUNVISOR HOLDER DRIVER’S SUNVISOR 6. Pull the driver’s door seal away from the driver’s  A-pillar. Gently pull out the driver’s A-pillar trim to release the clips. Q0N2014AG VEHICLE PANEL CLIP 2 CLIPS DRIVER’S A-PILLAR TRIM DRIVER’S DOOR  SEAL (Pull away.) CLIP DRIVER’S A-PILLAR

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 7. To prevent the clips from falling into the vehicle body, roll up a shop towel, and insert it between the driver’s A-pillar and the dashboard. Be careful not to damage the A-pillar trim. Q0N2015BG SHOP TOWEL DRIVER’S A-PILLAR DASHBOARD 8. Remove the driver’s A-pillar trim. Remove the shop towel and any clips that fell from the A-pillar.  NOTE: The upper clip will stay in the body. Q0N2016AG UPPER CLIP DRIVER’S  A-PILLAR TRIM (Remove.) DRIVER’S A-PILLAR TRIM 9. Remove the upper clip from the driver’s  A-pillar. Q0N2017AG Push 2 tabs. UPPER CLIP (Discard.) DRIVER’S A-PILLAR 10. Temporarily reinstall the driver’s A-pillar trim. Check the overlap between the headliner and the trim, according to service manual specifications. Remove the trim, and install the new clip (supplied). Q0N2018AG DRIVER’S  A-PILLAR TRIM (inside) NEW CLIP

AII 50024-50373 (1308) 5 of 25 11. Remove the driver’s dashboard panel, and unplug the vehicle connector. Q0N2019BG VEHICLE CONNECTOR 6 CLIPS DRIVER’S  DASHBOARD PANEL 12. Remove the driver’s air outlet. Q0N2020BG DRIVER’S  AIR OUTLET 2 CLIPS RETAINING  TAB SELF-TAPPING SCREW CLIP 13. Turn the knob and remove the driver’s dashboard undercover. Q0N2021BG PIN DRIVER’S DASHBOARD UNDER COVER KNOB (Turn.) CLIP 14. Remove the driver’s dashboard lower cover, and unplug the vehicle connectors. QAN2325AD VEHICLE  CONNECTORS 8 CLIPS DRIVER’S DASH- BOARD LOWER COVER

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 15. Attach tape to the upper column cover as shown. Q0N2023AG TAPE UPPER COLUMN COVER STEERING WHEEL 16. Lower the tilt lever, and turn the steering wheel 90° counterclockwise. Q0N2024BG PLASTIC TRIM TOOL STEERING WHEEL LOCK UPPER COLUMN COVER 17. Using a plastic trim tool, release the lock as shown. 18. Turn the steering wheel 180° clockwise. Using a plastic trim tool, release the lock as shown. Q0N2025BG LOCK UPPER COLUMN COVER PLASTIC TRIM TOOL 19. Secure the upper column cover to the meter panel with tape. Q0N2026AG TAPE 2 RETAINING TABS UPPER COLUMN COVER METER PANEL

AII 50024-50373 (1308) 7 of 25 20. Remove the two self-tapping screws from the front of the lower column cover. Q0N2027AG LOWER COLUMN COVER 2 SELF-TAPPING SCREWS 21. Remove the lower column cover. Q0N2028AG SELF-TAPPING SCREW LOWER COLUMN COVER 22. Remove the driver’s front door sill trim. Q0N2029BG 2 RETAINING TABS FRONT 3 CLIPS 2 HOOKS DRIVER’S FRONT DOOR SILL TRIM 23. Pull away the driver’s door opening seal, and remove the driver’s kick panel. Q0N2030AG DRIVER’S DOOR OPENING SEAL (Pull away.) DRIVER’S KICK PANEL 2 CLIPS

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. Installing the Antenna 24. Using scissors, cut one piece of urethane tape in half. Wrap the two halves of urethane tape around the antenna cable as shown. QB62501BK ANTENNA 60 mm (2.4 in.) 60 mm (2.4 in.) HALVES OF  URETHANE TAPE (Do not fold  the antenna cable.) URETHANE TAPE (Cut in half.) ANTENNA CABLE 25. Starting at the antenna end of the cable, measure and wrap one piece of urethane tape around the antenna cable as shown. QC50903AB 220 mm (8.7 in.) 10 mm (0.4 in.) ANTENNA CABLE URETHANE TAPE 26. Measure and wrap another piece of urethane tape around the antenna cable as shown. 27. Attach the antenna. • Measure and attach masking tape to the windshield as shown. QC11702AB MASKING TAPE 25 mm (1.0 in.) HEADLINER FRONT WINDSHIELD • Fold back the adhesive backing on the antenna as shown. QB51401CH ANTENNA ADHESIVE BACKING

AII 50024-50373 (1308) 9 of 25 • Using isopropyl alcohol on a shop towel, clean the windshield where the antenna will attach. • Attach the antenna with masking tape. Adjust the position of the antenna so there is equal spacing on both sides. QB51404CH Clean with isopropyl alcohol. ANTENNA MASKING TAPE HEADLINER ANTENNA Equal spacing on both sides. MASKING TAPE Align. • Carefully remove the adhesive backing from the antenna, and attach the antenna to the windshield. Press and hold the antenna firmly in place for 30 seconds. • Remove the masking tape. QB51405CH ADHESIVE BACKING (Remove.) ANTENNA MASKING TAPE (Remove.) 28. Gently pull back the headliner, and tuck the antenna cable behind the headliner. Be careful not to crease the headliner. QC50904AB ANTENNA CABLE HEADLINER HEADLINER VEHICLE PANEL ANTENNA CABLE 29. Route the antenna cable down the driver’s A-pillar along the vehicle harness. QC50905AB ANTENNA CABLE 6 CABLETIES DRIVER’S A-PILLAR VEHICLE HARNESS 30. Secure the antenna cable to the vehicle harness using six cable ties.

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 31. Route the antenna cable behind the dashboard. QC50906AB ANTENNA CABLE TOP VIEW FRONT STEERING HANGER BEAM Routing the Engine Starter Harness 32. Plug the three relays into the relay block on the engine starter harness. Q0N1801AG 40A FUSE LABEL 2 RELAYS RELAY 40A FUSE LABEL FUSE BLOCK RELAY BLOCK ENGINE STARTER HARNESS 3A FUSE LABEL 33. Using isopropyl alcohol on a shop towel, thoroughly clean the relay block and fuse block where the 3A fuse label and 40A fuse labels will attach. 34. Attach the 3A fuse label and two 40A fuse labels to the relay and fuse blocks. 35. Route the two 28-pin starter harness connectors upward as shown. QC50907AB ENGINE STARTER HARNESS STEERING HANGER BEAM ENGINE STARTER HARNESS  28-PIN CONNECTOR

AII 50024-50373 (1308) 11 of 25 36. Unplug the vehicle 28-pin connector. Q0N1804CG VEHICLE  28-PIN CONNECTOR ENGINE STARTER HARNESS  28-PIN CONNECTOR 37. Route the engine starter harness 28-pin connectors as shown, and plug the engine starter harness  28-pin connector into the vehicle 28-pin connector. 38. Route the engine starter harness 28-pin connector between the driver’s A-pillar and vehicle 28-pin connector as shown. Q0N1805BG VEHICLE 28-PIN CONNECTOR ENGINE STARTER HARNESS  28-PIN CONNECTOR TOP VIEW FRONT ENGINE STARTER HARNESS  28-PIN CONNECTOR DRIVER’S A-PILLAR VEHICLE  28-PIN CONNECTOR 39. Plug the other vehicle 28-pin connector into the engine starter harness 28-pin connector. 40. Secure the engine starter harness and the antenna cable to the vehicle frame with one cable tie. Q0N1806BG VEHICLE HARNESS CABLE TIE ENGINE STARTER HARNESS CABLE TIE ENGINE STARTER HARNESS VEHICLE FRAME ANTENNA CABLE ANTENNA CABLE 41. Secure the engine starter harness and the antenna cable to the vehicle harness with one cable tie.

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 42. Unplug the vehicle 5-pin connector from the fuse box, and plug it into the engine starter harness 5-pin connector. QC50908AB FRONT VIEW VEHICLE 5-PIN CONNECTOR ENGINE STARTER HARNESS  5-PIN CONNECTOR FUSE BOX FUSE BOX Plug in here. UNLOCK LOCK 1 3 1 2 2 Push. Push. Pull. 43. Plug the remaining 5-pin engine starter harness connector into the fuse box.  NOTE: Make sure that the engine starter harness 5- pin connector is securely connected to the fuse box. A loose connection can cause the engine to stall. 44. Attach the connector clip on the 5-pin connector to the hole in the vehicle panel. QC50909AB ENGINE STARTER HARNESS  5-PIN CONNECTOR FUSE BOX VEHICLE PANEL HOLE CONNECTOR CLIP 45. Slide the other clip onto the connector on the vehicle.  Note the direction and the orientation of the clip. QC50910AB ENGINE STARTER HARNESS CLIP VEHICLE CONNECTOR FRONT

AII 50024-50373 (1308) 13 of 25 If the vehicle is equipped with the accessory fog lights, go to step 47; otherwise, continue with step 46. 46. Plug the engine starter harness 4-pin connector into the fuse box. Go to step 49. QC50911AB FRONT VIEW FUSE BOX FUSE BOX Plug in here. ENGINE STARTER  HARNESS 4-PIN CONNECTOR 47. Unplug the fog light 4-pin connector from the fuse box, and plug it into the engine starter harness 4-pin connector. QC50912AB FRONT VIEW FUSE  BOX FUSE BOX Plug in here. ENGINE STARTER  HARNESS 4-PIN CONNECTOR FOG LIGHTS  4-PIN  CONNECTOR ENGINE STARTER  HARNESS 4-PIN CONNECTOR 48. Plug the remaining 4-pin connector into the fuse box.

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 49. Unplug the vehicle 24-pin connector, and plug the engine starter harness 24-pin connector into the vehicle 24-pin connector. QC50913AB FRONT VIEW FUSE BOX FUSE BOX ENGINE STARTER HARNESS 24-PIN CONNECTOR VEHICLE  24-PIN  CONNECTOR VEHICLE  24-PIN  CONNECTOR 50. Slide the clip from the engine starter harness 24-pin connector onto the bottom of the fuse box, then plug the remaining vehicle 24-pin connector into the engine starter harness 24-pin connector. QC50914AB FRONT VIEW FUSE BOX FUSE BOX ENGINE STARTER HARNESS  24-PIN CONNECTOR VEHICLE  24-PIN  CONNECTOR FUSE BOX ENGINE STARTER HARNESS  24-PIN CONNECTOR

AII 50024-50373 (1308) 15 of 25 51. Secure the engine starter harness to the vehicle harness with two cable ties. QC50915AB FUSE BOX ENGINE STARTER HARNESS VEHICLE HARNESS 2 CABLE TIES 52. Route the engine starter harness under the dashboard and toward the steering wheel. Q0N2004AG ENGINE STARTER HARNESS FRONT LEFT KNEE BOLSTER HOLE CLIP FRONT ENGINE STARTER HARNESS 53. Secure the engine starter harness to the hole in the left knee bolster using the clip on the engine starter harness as shown. 54. Locate the white tape on the engine starter harness, and loosely secure the engine starter harness to the dashboard with one cable tie at the white tape. Q0N2005AG ENGINE STARTER HARNESS CABLE TIE (Loosely secure.) DASHBOARD WHITE TAPE 55. Route the engine starter harness to the steering wheel as shown. Q0N2006BG ENGINE STARTER HARNESS VEHICLE CLIP WHITE TAPE FRONT BOTTOM VIEW 2 CABLE TIES VEHICLE HARNESS 56. Align the white tape on the engine starter harness with the vehicle clip, and secure the engine starter harness to the vehicle harness with two cable ties as shown.

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 57. Unplug the vehicle 7-pin connector from the ignition switch, and plug it into the engine starter harness  7-pin connector (black). Q0N2007AG VEHICLE 7-PIN  CONNECTOR ENGINE STARTER HARNESS 7-PIN CONNECTOR (BLACK) ENGINE STARTER HARNESS 7-PIN CONNECTOR (BLACK) IGNITION SWITCH STEERING WHEEL 58. Plug the remaining 7-pin connector (black) into the ignition switch. 59. Secure the 7-pin connectors and engine starter harness to the vehicle harness with one cable tie. Q090211BK VEHICLE HARNESS 7-PIN CONNECTORS CABLE TIE ENGINE STARTER HARNESS 60. Route the engine starter harness across the steering column as shown. Q0N2008AG VEHICLE  10-PIN  CONNECTOR ENGINE STARTER HARNESS ENGINE STARTER HARNESS 10- PIN CONNECTOR STEERING WHEEL WIPER SWITCH ENGINE STARTER HARNESS 10-PIN CONNECTOR 61. Unplug the vehicle 10-pin connector from the wiper switch, and plug it into the engine starter harness  10-pin connector. 62. Plug the remaining 10-pin connector into the wiper switch.

AII 50024-50373 (1308) 17 of 25 63. Secure the 10-pin connectors and engine starter harness to the vehicle harness with one cable tie. Q090302BK IGNITION SWITCH CABLE TIE 10-PIN CONNECTORS ENGINE STARTER HARNESS STEERING WHEEL 64. Unplug the vehicle 12-pin connector from the combination light switch, and plug it into the engine starter harness 12-pin connector. QA20704BG VEHICLE 12-PIN  CONNECTOR ENGINE STARTER HARNESS 12-PIN CONNECTOR STEERING WHEEL COMBINATION LIGHT SWITCH ENGINE STARTER HARNESS 12-PIN CONNECTOR 65. Plug the remaining 12-pin connector into the combination light switch.

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 66. Secure the engine starter harness to the vehicle harness with two cable ties. Check that the harness is secured without strain to the connectors or harness. NOTE: Make sure that the connectors and harness are not pinched, or interfering the steering wheel when moved for adjustment. Q0N2010BG ENGINE STARTER HARNESS VEHICLE HARNESS 2 CABLE TIES Do not stretch the left connector harness Do not strain the right connector harness. 67. Route the antenna cable along the engine starter harness as shown. QC50916AB ENGINE STARTER HARNESS FRONT LEFT KNEE BOLSTER CABLE TIE  (Loosely secure.) ANTENNA CABLE CABLE TIE ANTENNA CABLE CABLE TIE VEHICLE HARNESS DASHBOARD FUSE BOX 68. Secure the antenna cable to the engine starter harness with two cable ties. 69. Loosely secure the antenna cable to the dashboard with the cable tie installed in step 54.

AII 50024-50373 (1308) 19 of 25 Installing the Control Unit 70. Using isopropyl alcohol on a shop towel, clean the area where the urethane tape will attach. Q0N2305AG URETHANE TAPE VEHICLE UNIT (Clean with isopropyl alcohol.) 71. Attach a piece of urethane tape to the vehicle unit as shown. 72. Plug the antenna cable connector and the engine starter connector into the control unit. QC50917AB ENGINE STARTER HARNESS 28-PIN CONNECTOR CONTROL UNIT ANTENNA CABLE CONNECTOR 73. Attach the control unit bracket to the control unit. QC50918AB CONTROL UNIT CONTROL UNIT BRACKET 74. Secure the clip from the engine starter harness fuse block, and the clip from the engine starter harness into the control unit bracket. Q0N2308BG CONTROL UNIT BRACKET ENGINE STARTER HARNESS HOLE CLIP HOLE CLIP FUSE BLOCK

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 75. Remove the vehicle flange nut that secures the vehicle bracket. QC50919AB CONTROL UNIT BRACKET VEHICLE FLANGE NUT CONTROL UNIT BRACKET VEHICLE BRACKET VEHICLE FLANGE NUT VEHICLE BRACKET VEHICLE PANEL CONTROL UNIT BRACKET Align. 76. Install the control unit bracket on top of the vehicle bracket and align the brackets. Install the vehicle flange nut. 77. Secure the antenna cable and engine starter harness to the vehicle harness with one long cable tie. QC61401AY ENGINE STARTER HARNESS FRONT LONG CABLE TIE ANTENNA CABLE VEHICLE HARNESS CABLE TIE 78. Secure the antenna cable to the engine starter harness with one cable tie. 79. Bundle up the excess antenna cable, and secure it to the dashboard with the one cable tie loosely installed in step 69. QC61402AY ANTENNA CABLE (Bundle up the excess.) CABLE TIE DASHBOARD

AII 50024-50373 (1308) 21 of 25 80. Using isopropyl alcohol on a shop towel, clean the areas where the urethane tape will attach. Q090601AK Clean with isopropyl alcohol. 2 URETHANE TAPES LOWER COLUMN COVER (inside) 81. Attach two pieces of urethane tape to the inside of the lower column cover. 82. Open the hood. Using isopropyl alcohol on a shop towel, clean the hood where the caution label will be attached. Q0N2011AG ADHESIVE BACKING (Remove.) CAUTION LABEL HOOD (Clean with isopropyl alcohol.) 83. Remove the adhesive backing from the caution label, and attach the caution label to the hood. 84. Make sure that all harness and cables are routed properly and that all connectors are plugged in. 85. Reinstall all removed parts. 86. Reconnect the negative cable to the battery. 87. Check the operation of the headlights and wipers. 88. Press and hold the radio power button for two seconds to restore the radio and navigation (if equipped) system functions. 89. Reset the clock on vehicles without navigation. 90. Proceed to REMOTE ENGINE STARTER REGISTRATION and Check the operation of the Remote Control Engine Starter. REMOTE ENGINE STARTER REGISTRATION NOTE: Make sure the HDS has been upgraded to the latest version. 1. Retrieve the PCM code from the Interactive Network (iN). QC31909AC CAR ICON 2. Connect the HDS/MVCI tester to the OBD II data link connector, then turn the ignition switch to ON (II) position. 3. Start the HDS, and click the car icon.

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 4. Input the VIN and other required information into the HDS, then click the check button. QB32102BH Input the VIN and other required information. CHECK BUTTON 5. Select Honda Systems, then click the check button. QB32103AH Select  “Honda Systems.” CHECK BUTTON 6. Select R/C ENG STARTER and click the check button. QB32104AH Select  “R/C ENG STARTER.” CHECK BUTTON 7. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button. QB32105BH Select  “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.” CHECK BUTTON

AII 50024-50373 (1308) 23 of 25 8. The following message will display: Obtain PCM- code (IMMOBILIZER PCM CODE) from iN. The vehicle’s VIN will be required to obtain a password. (USA) Click the check button. QB32106AH “Obtain PCM-code” message. CHECK BUTTON 9. Input the PCM code, then click the check button. NOTE: To ensure security, the PCM code (password) is changed every day, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date on the HDS/MVCI tester should also be the same. QB32107BH Input the PCM-Code. CHECK BUTTON 10. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Turn the ignition off. QB32108CH “The registration of the Remote Control Engine Starter Unit has been completed.” 11. The following message will display: Check that engine can be started by the Transmitter. Click the check button. QB32109CH “Check that engine can be started by the Transmitter.” CHECK BUTTON 12. Perform the Check the operation of the Remote Control Engine Starter, then disconnect the HDS/ MVCI.

AII 50024-50373 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. Check the operation of the Remote Control Engine Starter Operating Conditions • The hood is closed. • The shift lever is in park. • The ignition switch is off and the key is outside the vehicle • All doors and tailgate closed and locked. Inspection 1. Press and release the engine/command button on the transmitter, within 2 seconds, press the lock/start button on the transmitter. Does the engine start? Yes - Operation is normal. No: • Make sure all “Operating Conditions” are met. • Check the engine starter harness connections. • Connect the HDS/MVCI and check for an indicated failure. (Refer to the Service Manual for troubleshooting.)

This indicator is displayed for some vehicles among them. LOCK/ START BUTTON © 2013 American Honda Motor Co., Inc. – All Rights Reserved. AII 50024-50373 (1308) 25 of 25 2. Press the engine/command button on the transmitter and release, within 2 seconds, then press the unlock/ stop button. Does the engine stop? Yes - Operation is normal. No - Check the engine starter harness connections. 3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions: NOTE: After each test the ignition key must be cycled, or the driver’s door must be opened and closed. • Move the shift lever out of the P position. • Unlock or open the doors or the tailgate. • Open the hood. • Insert the key in the ignition. • Press the brake pedal. Does the engine stop after each of these tests? Yes - Operation is normal. No - Check the engine starter harness connections. 4. Make sure the power windows and the moonroof do not function, and the shift lever does not move to any position when the vehicle system is started with the transmitter. 5. Start the vehicle system again, press the engine/command button on the transmitter two times, and check the vehicle condition on the display. 6. Check the operation of the transmitter when the vehicle is 120 m (400 ft.) away and in direct sight. 7. Press the unlock/stop button on the transmitter and verify that the doors unlock. Press the lock/start button, and verify that the doors lock. 8. Make sure the vehicle key can start the engine, and that the wipers and the headlights operate normally.