Philips AZT3202 Operation & User’s Manual

# 1 2 3 4 5 7 8 9 @ DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PROG DIGITAL FM TUNER 45 S ECO NDS ELE CT RO NIC SKI P P RO TE CT IO N C D RE W RI TA BL E C O M PA TI BL E ! 0 6 PRESET English Français Español English CONTROLS / POWER SUPPLY CONTROLS ( see figure 1 ) 1 OPEN 2 ..............opens the CD lid 2 DBB.....................switches the bass enhancement on and off. This button also switches acoustic feedback (the beep) on/off when it is pressed for more than 2 seconds 3 MODE .................selects the different playing possibilities: shuffle, shuffle repeat all, repeat, repeat all and SCAN 4 PROG...................programs CD tracks and radio stations, reviews the program 5 PRESET 3 ,4.....selects a preset tuner station (down, up) 6 FM.......................selects the radio on or off. 7 ............................display 8 2;, 9 .................- switches the player on, starts or pauses CD play - stops CD play, clears a program or switches the player off 9 TUNING ∞ , § TUNER : - (down,up) tunes to radio station; CD : - skips and searches CD tracks forwards or backwards. 0 RESUME .............stores the last position of a CD track played HOLD...................locks all buttons OFF......................switches RESUME and HOLD off ! LINE OUT/p 3 5 mm headphone jack and LINE OUT jack to connect the POWER SUPPLY / GENERAL INFOR Mains adapter (supplied or optionally available) Use only the AYT 3170 adapter (4.5 V / 300 mA direct current, positive pole to the center pin). Any other product may damage the player. 1 Make sure the local voltage corresponds to the power adapter’s voltage. 2 Connect the power adapter to the 4.5V DC jack of the player and to the wall outlet. Note: Always disconnect the adapter when you are not us Environmental information • All redundant packing material has been omitted. We make the packaging easily separable into two materia polyethylene (bags, protective foam sheet). • Your set consists of materials which can be recycled if specialized company. Please observe the local regulati disposal of packing materials, dead batteries and old e IMPORTANT SAFETY INSTRUCTION 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat regis- ters, stoves, or other apparatus (including amplifiers) that produce heat. 9. Only use attachments/accessories specified by the manufacturer. 10. Use only with a cart, stand, tripo specified by the manufacturer or sol When a cart is used, use caution wh cart/apparatus combination to avoid 11. Refer all servicing to qualified service person required when the apparatus has been damaged the power-supply cord or plug is damaged, liquid objects have fallen into the apparatus, or when th exposed to rain or moisture, does not operate n dropped. 12. Battery usage CAUTION – To preven may result in bodily injury, property damage or dam G Install ALL batteries correctly, + and - as marked G Do not mix batteries (OLD and NEW or CAR ALKALINE, etc.). G Remove batteries when the unit is not used for a EL Return your Warranty Registration card today to ensure you receive all the benefits you’re entitled to. • Once your Philips purchase is regis- tered, you’re eligible to receive all the privileges of owning a Philips product. • So complete and return the Warranty Registration Card enclosed with your purchase at once, and take advantage of these important benefits. Warranty Verification Registering your product within 10 days confirms your right to maximum protection under the terms and conditions of your Philips warranty. Owner Confirmation Your completed Warranty Registration Card serves as verifica- tion of ownership in the event of product theft or loss. Model Registration Returning your Warranty Registration Card right away guarantees you’ll receive all the information and special offers which you qualify for as the owner of your model. This “bolt of lightning” indicates uninsulated material within your unit may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering. The “exclamation point” calls attention to features for which you should read the enclosed litera- ture closely to prevent operating and maintenance problems. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. CAUTION: To prevent electric shock, match wide blade of plug to wide slot, and fully insert. For Customer Use Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference. Model No. _____________________ Serial No. ______________________ Know these safety symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. MAC5097 Renvoyez votre carte d’enregistrement de ga assurer de recevoir tous les avantages auxque • Dès que l’achat de votre appareil Philips est enregistré, vous avez droit à tous les avantages dont bénéficient les possesseurs des produits Philips. • Remplissez et re d’enregistremen votre appareil sa ficierez de ces a Vérification de garantie Enregistrez votre pro- duit dans les 10 jours pour confirmer votre droit à une protection maximum selon les termes et les conditions de votre garantie Philips. Confirmation de possession Votre carte d’enreg- istrement de garantie prouve que vous pos- sédez l’appareil en cas de vol ou de perte du produit. E du Ren d’e gar pou rec info les ave pos Cet «éclair à pointe de flèche» indique qu’un matériau non isolé, situé à l’intérieur de l’unité, risque de provoquer un choc électrique. Pour la sécurité de chacun, nous vous prions de ne pas retirer le boîtier de ce produit. Le «point d’exclamation» attire votre attention sur des sujets risquant de provoquer des problèmes de fonctionnement et d’entretien si vous ne lisez pas les informations s’y reportant. DANGER : ÉQUIPEMENT A L HUMIDITÉ EXCES RISQUES D’INCEN ÉLECTRIQUE. ATTENTIO chocs électrique plus large de la f correspondante jusqu’au fond. Cet espace vou Inscrivez ci-dessou situé à l’arrière du information pour v N° de modèle _ N° de série ___ Connaissez ces symboles de sécurite AT T E N T I O N RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR ATTENTION: POUR REDUIRE LE RESQUE DE CHOC ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE (NI LE PANNEAU ARRIERE). CET APPAREIL NE COMPORTE AUCUNE PIECE POUVANT TRE REPAREE PAR L’UTILISATEUR. CONFIER SON ENTRETIEN A UN TECHNICIEN QUALIFIE. PHILIPS CONSUMER ELECTRONICS NORTH AMERICA Knoxville, Tennessee 37914-1810, U.S.A. Audio Audio Need help? Call us! Philips representatives are ready to help you with any questions about your new product. CALL US BEFORE YOU CONSIDER RETURNING THE PRODUCT! 1-800-531-0039 or visit us on the web at www.philips.com S E E W H Y I N S I D E I M P O R T A N T ! Return your Warranty Registration Card within 10 days Portable CD Player AZT3200 • AZT3201, AZT3202 Meet Philips at the Internet http://www.philips.com 1 AZT3200, AZT3201, AZT3202 3140 115 3065.1

CD TUNING DBB MODE PRESET DIGITAL FM TUNER DIGITAL FM TUNER DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGIT DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGITAL FM TUNER 45 S ECO ND S EL ECT RO NIC SKI P P RO TE CT IO N C D RE W RI TA BL E C O M PA TI BL E DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGITAL FM TUNER DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGITAL FM TUNER DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGITAL FM TUNER 45 S ECO ND S E LEC TR ON IC SKI P P RO TE CT IO N C D RE W RI TA BL E C O M PA TI BL E 45 SE CON DS EL ECTR ONI C SK IP P ROT EC TIO N CD RE W RI T A B L E C O M P A T I B L E 45 SE CON DS E LEC TRO NIC SKI P P RO TE CT IO N CD RE W RI T A B L E C O M P A T I B L E 45 S EC ONDS E LEC TRO NIC SKI P P ROT ECT ION CD RE WR IT AB LE C O M P A TI B L E # % $ 1 2 3 4 5 7 8 9 @ DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PROG DIGITAL FM TUNER 45 S ECO NDS ELE CT RO NIC SKI P P RO TE CT IO N C D RE W RI TA BL E C O M PA TI BL E ! 0 6 PRESET English CONTROLS / POWER SUPPLY CONTROLS ( see figure 1 ) 1 OPEN 2 ..............opens the CD lid 2 DBB.....................switches the bass enhancement on and off. This button also switches acoustic feedback (the beep) on/off when it is pressed for more than 2 seconds 3 MODE .................selects the different playing possibilities: shuffle, shuffle repeat all, repeat, repeat all and SCAN 4 PROG...................programs CD tracks and radio stations, reviews the program 5 PRESET 3 ,4.....selects a preset tuner station (down, up) 6 FM.......................selects the radio on or off. 7 ............................display 8 2;, 9 .................- switches the player on, starts or pauses CD play - stops CD play, clears a program or switches the player off 9 TUNING ∞ , § TUNER : - (down,up) tunes to radio station; CD : - skips and searches CD tracks forwards or backwards. 0 RESUME .............stores the last position of a CD track played HOLD...................locks all buttons OFF......................switches RESUME and HOLD off ! LINE OUT/p........3.5 mm headphone jack and LINE OUT jack to connect the player to another audio input of an additional appliance. @ VOL E ............adjusts the volume # 4.5V DC...............jack for external power supply $ ............................belt clip holder % ............................type plate POWER SUPPLY / GENERAL INFORM Mains adapter (supplied or optionally available) Use only the AYT 3170 adapter (4.5 V / 300 mA direct current, positive pole to the center pin). Any other product may damage the player. 1 Make sure the local voltage corresponds to the power adapter’s voltage. 2 Connect the power adapter to the 4.5V DC jack of the player and to the wall outlet. Note: Always disconnect the adapter when you are not usi Environmental information • All redundant packing material has been omitted. We h make the packaging easily separable into two materials polyethylene (bags, protective foam sheet). • Your set consists of materials which can be recycled if specialized company. Please observe the local regulatio disposal of packing materials, dead batteries and old eq CD player and CD handling • Do not touch the lens A of the CD player. • Do not expose the unit, batteries or CDs to humidity, rain, sand or excessive heat (caused by heating equipment or direct sunlight). • You can clean the CD player with a soft, slightly dampened, lint-free cloth. Do not use any cleaning agents as they may have a corrosive effect. • To clean the CD, wipe it in a straight line from the center toward the edge using a soft, lint-free cloth. A c damage the disc! Never write on a CD or attach a stick • The lens may cloud over when the unit is moved sudden surroundings. Playing a CD is not possible then. Leave t environment until the moisture has evaporated. • Active mobile phones in the vicinity of the CD player ma • Avoid dropping the unit as this may cause damage. Headphones HS383 • Connect the supplied headphones to the LINE OUT/p jack of the player. Note: LINE OUT/p can also be used for connecting this set to your HiFi system.To adjust the sound and volume, use the controls on the connected audio equipment and on the CD player. IMPORTANT! Hearing safety: Do not play your headphones at a high volu advise that continuous use at high volume can permanently Traffic safety: Do not use headphones while driving a vehic hazard and it is illegal in many countries. Even if your head type designed to let you hear outside sounds, do not turn u that you cannot hear what is going on around you. QUICK START MISE EN SERVICE RAPIDE ENCENDIDO RAPIDO Batteries (supplied or optionally available) You can use the following batteries with this CD-player: • normal batteries type LR6, UM3 or AA (preferably Philips), or • alkaline batteries type LR6, UM3 or AA (preferably Philips). Notes:– Old and new or different types of batteries should not be combined. – Remove batteries if they are empty or if the player is not going to be used for a long time. Inserting batteries 1 Push OPEN 2 to open the CD lid. 2 Open the battery compartment and insert either 2 normal or alkaline batteries. Battery indication The approximate power level of your batteries is shown in the display. Battery full Battery two-thirds full Battery one-third full Battery dead or empty. When the batteries are dead or empty, the symbol flashes, bAtt is displayed, and the beep tone sounds repeatedly. Average playing time of batteries under normal conditions Battery type ESP on Power Save Normal 5 hours 6 hours Alkaline 16 hours 20 hours Batteries contain chemical substances, so they should be disposed of properly. 1

CD TUNING DBB MODE PRESET DIGITAL FM TUNER DIGITAL FM TUNER DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGIT DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGITAL FM TUNER 45 S ECO ND S EL ECT RO NIC SKI P P RO TE CT IO N C D RE W RI TA BL E C O M PA TI BL E DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGITAL FM TUNER DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGITAL FM TUNER DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGITAL FM TUNER 45 S ECO ND S E LEC TR ON IC SKI P P RO TE CT IO N C D RE W RI TA BL E C O M PA TI BL E 45 SE CON DS EL ECTR ONI C SK IP P ROT EC TIO N CD RE W RI T A B L E C O M P A T I B L E 45 SE CON DS E LEC TRO NIC SKI P P RO TE CT IO N CD RE W RI T A B L E C O M P A T I B L E 45 S EC ONDS E LEC TRO NIC SKI P P ROT ECT ION CD RE WR IT AB LE C O M P A TI B L E CD player and CD handling • Do not touch the lens A of the CD player. • Do not expose the unit, batteries or CDs to humid rain, sand or excessive heat (caused by heating equipment or direct sunlight). • You can clean the CD player with a soft, slightly dampened, lint-free cloth. Do not use any cleanin agents as they may have a corrosive effect. • To clean the CD, wipe it in a straight line from th center toward the edge using a soft, lint-free clo damage the disc! Never write on a CD or attach • The lens may cloud over when the unit is moved surroundings. Playing a CD is not possible then. L environment until the moisture has evaporated. • Active mobile phones in the vicinity of the CD pla • Avoid dropping the unit as this may cause damag Headphones HS383 • Connect the supplied headphones to the LINE OU jack of the player. Note: LINE OUT/p can also be used for connecting this set to your HiFi system.To adjust sound and volume, use the controls on the conne audio equipment and on the CD player. IMPORTANT! Hearing safety: Do not play your headphones at a hi advise that continuous use at high volume can perm Traffic safety: Do not use headphones while driving hazard and it is illegal in many countries. Even if you type designed to let you hear outside sounds, do not that you cannot hear what is going on around you. QUICK START MISE EN SERVICE RAPIDE ENCENDIDO RAPIDO Batteries (supplied or optionally available) You can use the following batteries with this CD-player: • normal batteries type LR6, UM3 or AA (preferably Philips), or • alkaline batteries type LR6, UM3 or AA (preferably Philips). Notes:– Old and new or different types of batteries should not be combined. – Remove batteries if they are empty or if the player is not going to be used for a long time. Inserting batteries 1 Push OPEN 2 to open the CD lid. 2 Open the battery compartment and insert either 2 normal or alkaline batteries. Battery indication The approximate power level of your batteries is shown in the display. Battery full Battery two-thirds full Battery one-third full Battery dead or empty. When the batteries are dead or empty, the symbol flashes, bAtt is displayed, and the beep tone sounds repeatedly. Average playing time of batteries under normal conditions Battery type ESP on Power Save Normal 5 hours 6 hours Alkaline 16 hours 20 hours Batteries contain chemical substances, so they should be disposed of properly.

Playback information • If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded properly, nF dISC is displayed, indicating that the CD has not been finalized. In that case, use FINALIZE on your CD recorder to complete the recording. • When playing a CD-Rewritable (CD-RW), please note that it takes 3–15 seconds after pressing 2; for sound reproduction to start. • Playback will stop if you open the CD lid. • While the CD is read, 1 -:- flashes in the display. Volume and bass Volume adjustment • Adjust the volume by using VOL E. Bass adjustment • Press DBB to switch the bass enhancement on or off y is shown if the bass enhancement is activated. DBB FEATURES Programming track numbers You can store up to 30 tracks to play in a program. A single track may be stored more than once in the program. 1 While playback is stopped, select a track with ∞or §. 2 Press PROG to store the track. yprogram lights up; the track number programmed and P with the total number of stored tracks are displayed. 3 Select and store all desired tracks in this way. 4 Press 2; to start playback of your selected tracks. yprogram is shown and playback starts. • You can review the program by pressing PROG for more than 2 seconds. yThe display shows all the stored tracks in sequence. Notes: – If you press PROG and there is no track selected, SEL is displayed. – If you try to store more than 30 tracks, FULL is displayed. Clearing the program • While playback is stopped, press 9 to clear program. yCLR is displayed once, program goes off, and the program is cleared. Note: The program will also be cleared if the power supply is interrupted, or if the CD-player lid is opened, or if the set switches off automatically. FEATURES RESUME and HOLD You can interrupt playback and continue (even after an extended period of time) from the position where playback stopped (RESUME) and you can lock all buttons of the set so that no action will be executed (HOLD). Use the RESUME–HOLD–OFF slider for these functions. RESUME – continuing from where you have stopped 1 Switch the slider to RESUME during playback to activa yresume is shown. 2 Press 9 whenever you want to stop playback. 3 Press 2; whenever you want to resume playback. yresume is shown and playback continues from where you have stopped. • To deactivate RESUME, switch the slider to OFF. yresume goes off. HOLD – locking all buttons You can lock the buttons of the set by switching the slider key is pressed, no action will be executed. This is of use, f transporting the player in a bag. With HOLD activated, you activation of other functions. 1 Switch the slider to HOLD to activate HOLD. yAll buttons are locked. HoLd is shown when you press any button. If the set is switched off, hold will be shown only when 2; or FM is pressed. 2 To deactivate HOLD, switch the slider to OFF. Note: If you deactivate HOLD by switching the slider to RE you will be activating the RESUME function. Selecting different playing possibilities−MODE It is possible to play tracks in random order, to repeat a single track or the entire CD, and to play the first few seconds of each track. 1 Press MODE during playback as often as required in order to activate one of the following ‘modes’. The active mode is shown in the display. yshuffle : All tracks of the CD are played in random order until all of them have been played once. yshuffle repeat all : All tracks of the CD are played repeatedly in random order. yrepeat : The current track is played repeatedly. yrepeat all : The entire CD is played repeatedly. ySCAN: The first 10 seconds of each of the remain- ing tracks are played in sequence. 2 Playback starts in the chosen mode after 2 seconds. • To return to normal playback, press MODE repeatedly until the display shows no active modes. ESP / Power Save Mode With a conventional portable CD-player you might have experienced that the music stopped e.g. when you were jogging. The ELECTRONIC SKIP PROTECTION prevents loss of sound caused by light vibrations and shocks. Continuous playback is ensured. However ESP does not prevent playback interruptions during vigorous running. It also does not protect the unit against any damage caused by dropping! On this set ESP is default on. It is possible to set ESP off and enter the Power Save mode The Power Save mode helps to extend battery Selecting a track and searching Selecting a track during playback • Briefly press ∞ or § once or several times to skip to the current, previous or next track. yPlayback continues with the selected track, and the track’s number is displayed. Selecting a track when playback is stopped 1 Briefly press ∞ or § once or several times to select the desired track. The track number is displayed. 2 Press 2; to start CD play. yPlayback starts with the selected track. Searching for a passage during playback 1 Keep ∞ or § pressed to find a particular passage in a backward or forward direction. ySearching starts while playback continues at low volume. After 2 seconds the search speeds up. 2 Release the button when you reach the desired passage. yPlayback continues from this position. Notes: – If the player is in SCAN mode (see MODE chapter), searching is not possible. BELT CLIP CLIP CEINTURE C English (supplied or optionally available) 1 To attach the belt clip to the CD player, position the shaped g the belt grip) so that it fits into the belt clip hole of the CD p LOCK as indicated on the CD player. 2 To detach, gently lift the belt clip and turn to RELEASE as ind Français (fourni ou en option) 1 Pour fixer le clip ceinture, placez l’attache (située sur le dos d à cet effet sur l’appareil. Tournez l’attache jusqu’à LOCK, com 2 Pour enlever l’attache, soulevez-la doucement et tournez-la j Español (suministrado o disponible de forma opciona 1 Para ponerse el cinturón, encaje el broche (en la parte posterior del cinturón de cierre. Gire el cierre hasta LOCK tal y como se in 2 Para quitárselo, levante con cuidado el cinturón y gire hasta REL BELT CLIP LIFT LOCK RELEASE CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. ATTENTION L’utilisation de commandes ou de réglages ou l’exécution de procédures autres que celles décrites dans le présent manuel risque d’entraîner une exposition à un rayonnement dangereux ou d’avoir d’autres conséquences sur la sécurité. PRECAUCIÓN La utilización de controles o ajustes y la realización de procedimientos distintos de los contenidos en este manual pueden provocar la exposición a radiaciones peligrosas y a otros peligros. El aparato cumple las normas FCC, Parte 15 y 21 CFR 1040.10. Funcionamiento dependiente de dos condiciones siguientes: 1. Este aparato no puede provocar interferencia dañina, y 2. Este aparato debe aceptar cualquier interferencia recibida, incluyendo las interferencias que pueden provocar un funcionamiento insuficiente. L’appareil répond aux normes FCC, Part 15 et 21 CFR 1040.10. Fonctionnement soumis aux deux conditions suivantes : 1. Cet appareil ne doit pas provoquer d’interférences nuisibles, et 2. Cet appareil doit accepter toute interférence reçue, y compris les interférences susceptibles de provoquer un fonctionement peu satisfaisant. The set complies with the FCC-Rules, Part 15 and with 21 CFR 1040.10. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Canada English: This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. Français : Cet appareil numérique n'émet pas de bruits radioélectriques dépas- sant les limites applicables aux appareils numériques de Classe B prescrites dans le Règlement sur le Brouillage Radioélectrique édicté par le Ministère des Communications du Canada. Radio Play You can tune to any FM station automatically or manually. 1 Press FM to switch the radio on. Tuning to radio stations automatically 1 Keep ∞or § pressed for at least 2 second. yThe radio tunes to a station with sufficient strength and radio play starts. The current waveband and frequency are displayed. 2 Repeat searching until you find the desired radio station. Tuning to radio stations manually 1 Keep ∞or § pressed. 2 Release ∞or §, then briefly press ∞or § again when you are close to the desired frequency. 3 Briefly press ∞or § repeatedly until you reach the desired frequency. yRadio play starts. The current waveband and frequency are displayed. • To switch from radio play to CD play, press 2; . • Press FM or 9 to switch the radio off.

You can store up to 30 tracks to play in a program. A single track may be stored more than once in the program. 1 While playback is stopped, select a track with ∞or §. 2 Press PROG to store the track. yprogram lights up; the track number programmed and P with the total number of stored tracks are displayed. 3 Select and store all desired tracks in this way. 4 Press 2; to start playback of your selected tracks. yprogram is shown and playback starts. • You can review the program by pressing PROG for more than 2 seconds. yThe display shows all the stored tracks in sequence. Notes: – If you press PROG and there is no track selected, SEL is displayed. – If you try to store more than 30 tracks, FULL is displayed. Clearing the program • While playback is stopped, press 9 to clear program. yCLR is displayed once, program goes off, and the program is cleared. Note: The program will also be cleared if the power supply is interrupted, or if the CD-player lid is opened, or if the set switches off automatically. FEATURES RESUME and HOLD You can interrupt playback and continue (even after an extended period of time) from the position where playback stopped (RESUME) and you can lock all buttons of the set so that no action will be executed (HOLD). Use the RESUME–HOLD–OFF slider for these functions. RESUME – continuing from where you have stopped 1 Switch the slider to RESUME during playback to activate RESUME. yresume is shown. 2 Press 9 whenever you want to stop playback. 3 Press 2; whenever you want to resume playback. yresume is shown and playback continues from where you have stopped. • To deactivate RESUME, switch the slider to OFF. yresume goes off. HOLD – locking all buttons You can lock the buttons of the set by switching the slider to HOLD. Now, when a key is pressed, no action will be executed. This is of use, for example, when transporting the player in a bag. With HOLD activated, you can avoid accidental activation of other functions. 1 Switch the slider to HOLD to activate HOLD. yAll buttons are locked. HoLd is shown when you press any button. If the set is switched off, hold will be shown only when 2; or FM is pressed. 2 To deactivate HOLD, switch the slider to OFF. Note: If you deactivate HOLD by switching the slider to RESUME, you will be activating the RESUME function. Troubleshooting WARNING: Under no circumstances should you try to rep this will invalidate the warranty. If a fault occurs, first che before taking the unit for repair. If you are unable to solve these hints, consult your dealer or service center. The CD player has no power, or playback does not s • Check that your batteries are not dead or empty, that th correctly, that the contact pins are clean. • Your adapter connection may be loose. Connect it secu • For in-car use, check that the car ignition is on. Also ch The indication no diSC is displayed • Check that the CD is clean and correctly inserted (label • If your lens has steamed up, wait a few minutes for th The indication nF diSC is displayed • CD-RW (CD-R) was not recorded properly. Use FINALIZ The indication HOLD is on and/or there is no reaction • If HOLD is activated, then deactivate it. • Electrostatic discharge. Disconnect power or remove batt The CD skips tracks • The CD is damaged or dirty. Replace or clean the CD. • RESUME, SHUFFLE or PROGRAM is active. Switch off w No sound or bad sound quality. • PAUSE might be active Press 2; Selecting different playing possibilities−MODE It is possible to play tracks in random order, to repeat a single track or the entire CD, and to play the first few seconds of each track. 1 Press MODE during playback as often as required in order to activate one of the following ‘modes’. The active mode is shown in the display. yshuffle : All tracks of the CD are played in random order until all of them have been played once. yshuffle repeat all : All tracks of the CD are played repeatedly in random order. yrepeat : The current track is played repeatedly. yrepeat all : The entire CD is played repeatedly. ySCAN: The first 10 seconds of each of the remain- ing tracks are played in sequence. 2 Playback starts in the chosen mode after 2 seconds. • To return to normal playback, press MODE repeatedly until the display shows no active modes. ESP / Power Save Mode With a conventional portable CD-player you might have experienced that the music stopped e.g. when you were jogging. The ELECTRONIC SKIP PROTECTION prevents loss of sound caused by light vibrations and shocks. Continuous playback is ensured. However ESP does not prevent playback interruptions during vigorous running. It also does not protect the unit against any damage caused by dropping! On this set ESP is default on. It is possible to set ESP off and enter the Power Save mode. The Power Save mode helps to extend battery EL4967E007 / 8-02 BEFORE REQUESTING EXCHANGE... Please check your owner's manual for assistance. If you have additi at 1-800-531-0039. EXCHANGING A PRODUCT IN U.S.A., PUERTO RICO, OR U.S.VIRGIN ISLANDS... Contact 1-800-531-0039 to arrange an exchange. Or, ship the prod freight prepaid, and with proof of purchase enclosed, to the addres Philips Exchange Program Suite A 406 North Irish Street Greeneville TN 37745 (In U.S.A., Puerto Rico, and U.S.Virgin Islands, all implied warranties ranties of merchantability and fitness for a particular purpose, are li the duration of this express warranty. But, because some states do on how long an implied warranty may last, this limitation may not a EXCHANGING A PRODUCT IN CANADA... Please contact Philips at: 1-800-661-6162 (French Speaking) 1-800-531-0039 (English or Spanish Speaking (In Canada, this warranty is given in lieu of all other warranties. No expressed or implied, including any implied warranties of merchant particular purpose. Philips is not liable under any circumstances fo special, incidental or consequential damages, howsoever incurred, e possibility of such damages.) REMEMBER... Please record below the model and serial numbers found on the p out and mail your warranty registration card promptly. It will be ea you if necessary. MODEL # ____________________________________ SERIAL # ____________________________________ This warranty gives you specific legal rights.You may have which vary from state/province to state/province BELT CLIP CLIP CEINTURE CINTURÓN DE CIERRE English (supplied or optionally available) 1 To attach the belt clip to the CD player, position the shaped grip (found on the back of the belt grip) so that it fits into the belt clip hole of the CD player. Turn the clip to LOCK as indicated on the CD player. 2 To detach, gently lift the belt clip and turn to RELEASE as indicated on the CD player. Français (fourni ou en option) 1 Pour fixer le clip ceinture, placez l’attache (située sur le dos du clip) dans le trou prévu à cet effet sur l’appareil. Tournez l’attache jusqu’à LOCK, comme indiqué sur l’appareil. 2 Pour enlever l’attache, soulevez-la doucement et tournez-la jusqu’à RELEASE. Español (suministrado o disponible de forma opcional) 1 Para ponerse el cinturón, encaje el broche (en la parte posterior del cinturón) en el orificio del cinturón de cierre. Gire el cierre hasta LOCK tal y como se indica. 2 Para quitárselo, levante con cuidado el cinturón y gire hasta RELEASE tal y como se indica. BELT CLIP LIFT LOCK RELEASE CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. ATTENTION L’utilisation de commandes ou de réglages ou l’exécution de procédures autres que celles décrites dans le présent manuel risque d’entraîner une exposition à un rayonnement dangereux ou d’avoir d’autres conséquences sur la sécurité. PRECAUCIÓN La utilización de controles o ajustes y la realización de procedimientos distintos de los contenidos en este manual pueden provocar la exposición a radiaciones peligrosas y a otros peligros. Radio Play You can tune to any FM station automatically or manually. 1 Press FM to switch the radio on. Tuning to radio stations automatically 1 Keep ∞or § pressed for at least 2 second. yThe radio tunes to a station with sufficient strength and radio play starts. The current waveband and frequency are displayed. 2 Repeat searching until you find the desired radio station. Tuning to radio stations manually 1 Keep ∞or § pressed. 2 Release ∞or §, then briefly press ∞or § again when you are close to the desired frequency. 3 Briefly press ∞or § repeatedly until you reach the desired frequency. yRadio play starts. The current waveband and frequency are displayed. • To switch from radio play to CD play, press 2; . • Press FM or 9 to switch the radio off. FEATURES / TROUBLESHOOT The headphone wire is used as an FM antenna. If necessary, move it for optimum reception. Storing radio stations You can store up to 30 radio stations (1-30). 1 Tune to a desired radio station and press PROG. 2 Press PRESET3 ,4 repeatedly if necessary to select the number that should be assigned to this radio station. 3 Press PROG while PRESET is blinking to confirm the storage. yPRESET, the waveband, the frequency and the preset number of the stored station are displayed. 4 Store all desired stations this way. Note: Already stored stations can be recognized by the indicator PRESET and the preset number. Tuning to a stored radio station 1 Press FM to switch the radio ON. 2 Press PRESET3 ,4 once or more to find your preset sta yRadio play starts. program, the waveband, the preset number of the stored station are displayed Antennas

You can interrupt playback and continue (even after an extended period of time) from the position where playback stopped (RESUME) and you can lock all buttons of the set so that no action will be executed (HOLD). Use the RESUME–HOLD–OFF slider for these functions. RESUME – continuing from where you have stopped 1 Switch the slider to RESUME during playback to activate RESUME. yresume is shown. 2 Press 9 whenever you want to stop playback. 3 Press 2; whenever you want to resume playback. yresume is shown and playback continues from where you have stopped. • To deactivate RESUME, switch the slider to OFF. yresume goes off. HOLD – locking all buttons You can lock the buttons of the set by switching the slider to HOLD. Now, when a key is pressed, no action will be executed. This is of use, for example, when transporting the player in a bag. With HOLD activated, you can avoid accidental activation of other functions. 1 Switch the slider to HOLD to activate HOLD. yAll buttons are locked. HoLd is shown when you press any button. If the set is switched off, hold will be shown only when 2; or FM is pressed. 2 To deactivate HOLD, switch the slider to OFF. Note: If you deactivate HOLD by switching the slider to RESUME, you will be activating the RESUME function. Troubleshooting WARNING: Under no circumstances should you try to repair the set yourself as this will invalidate the warranty. If a fault occurs, first check the points listed, before taking the unit for repair. If you are unable to solve a problem by following these hints, consult your dealer or service center. The CD player has no power, or playback does not start • Check that your batteries are not dead or empty, that they are inserted correctly, that the contact pins are clean. • Your adapter connection may be loose. Connect it securely. • For in-car use, check that the car ignition is on. Also check player’s batteries. The indication no diSC is displayed • Check that the CD is clean and correctly inserted (label-side upward). • If your lens has steamed up, wait a few minutes for this to clear. The indication nF diSC is displayed • CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder. The indication HOLD is on and/or there is no reaction to controls • If HOLD is activated, then deactivate it. • Electrostatic discharge. Disconnect power or remove batteries for a few seconds. The CD skips tracks • The CD is damaged or dirty. Replace or clean the CD. • RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on. EL4967E007 / 8-02 BEFORE REQUESTING EXCHANGE... Please check your owner's manual for assistance. If you have additional questions, call us at 1-800-531-0039. EXCHANGING A PRODUCT IN U.S.A., PUERTO RICO, OR U.S.VIRGIN ISLANDS... Contact 1-800-531-0039 to arrange an exchange. Or, ship the product, insured and freight prepaid, and with proof of purchase enclosed, to the address listed below. Philips Exchange Program Suite A 406 North Irish Street Greeneville TN 37745 (In U.S.A., Puerto Rico, and U.S.Virgin Islands, all implied warranties, including implied war- ranties of merchantability and fitness for a particular purpose, are limited in duration to the duration of this express warranty. But, because some states do not allow limitations on how long an implied warranty may last, this limitation may not apply to you.) EXCHANGING A PRODUCT IN CANADA... Please contact Philips at: 1-800-661-6162 (French Speaking) 1-800-531-0039 (English or Spanish Speaking) (In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed or implied, including any implied warranties of merchantability or fitness for a particular purpose. Philips is not liable under any circumstances for any direct, indirect, special, incidental or consequential damages, howsoever incurred, even if notified of the possibility of such damages.) REMEMBER... Please record below the model and serial numbers found on the product.Also, please fill out and mail your warranty registration card promptly. It will be easier for us to notify you if necessary. MODEL # ____________________________________ SERIAL # ____________________________________ This warranty gives you specific legal rights.You may have other rights which vary from state/province to state/province. BELT CLIP CLIP CEINTURE CINTURÓN DE CIERRE English (supplied or optionally available) 1 To attach the belt clip to the CD player, position the shaped grip (found on the back of the belt grip) so that it fits into the belt clip hole of the CD player. Turn the clip to LOCK as indicated on the CD player. 2 To detach, gently lift the belt clip and turn to RELEASE as indicated on the CD player. Français (fourni ou en option) 1 Pour fixer le clip ceinture, placez l’attache (située sur le dos du clip) dans le trou prévu à cet effet sur l’appareil. Tournez l’attache jusqu’à LOCK, comme indiqué sur l’appareil. 2 Pour enlever l’attache, soulevez-la doucement et tournez-la jusqu’à RELEASE. Español (suministrado o disponible de forma opcional) 1 Para ponerse el cinturón, encaje el broche (en la parte posterior del cinturón) en el orificio del cinturón de cierre. Gire el cierre hasta LOCK tal y como se indica. 2 Para quitárselo, levante con cuidado el cinturón y gire hasta RELEASE tal y como se indica. BELT CLIP LIFT LOCK RELEASE Radio Play You can tune to any FM station automatically or manually. 1 Press FM to switch the radio on. Tuning to radio stations automatically 1 Keep ∞or § pressed for at least 2 second. yThe radio tunes to a station with sufficient strength and radio play starts. The current waveband and frequency are displayed. 2 Repeat searching until you find the desired radio station. Tuning to radio stations manually 1 Keep ∞or § pressed. 2 Release ∞or §, then briefly press ∞or § again when you are close to the desired frequency. 3 Briefly press ∞or § repeatedly until you reach the desired frequency. yRadio play starts. The current waveband and frequency are displayed. • To switch from radio play to CD play, press 2; . • Press FM or 9 to switch the radio off. FEATURES / TROUBLESHOOTING The headphone wire is used as an FM antenna. If necessary, move it for optimum reception. Storing radio stations You can store up to 30 radio stations (1-30). 1 Tune to a desired radio station and press PROG. 2 Press PRESET3 ,4 repeatedly if necessary to select the number that should be assigned to this radio station. 3 Press PROG while PRESET is blinking to confirm the storage. yPRESET, the waveband, the frequency and the preset number of the stored station are displayed. 4 Store all desired stations this way. Note: Already stored stations can be recognized by the indicator PRESET and the preset number. Tuning to a stored radio station 1 Press FM to switch the radio ON. 2 Press PRESET3 ,4 once or more to find your preset station. yRadio play starts. program, the waveband, the frequency and the preset number of the stored station are displayed. Antennas

CONTROLS ( see figure 1 ) 1 OPEN 2 ..............opens the CD lid 2 DBB.....................switches the bass enhancement on and off. This button also switches acoustic feedback (the beep) on/off when it is pressed for more than 2 seconds 3 MODE .................selects the different playing possibilities: shuffle, shuffle repeat all, repeat, repeat all and SCAN 4 PROG...................programs CD tracks and radio stations, reviews the program 5 PRESET 3 ,4.....selects a preset tuner station (down, up) 6 FM.......................selects the radio on or off. 7 ............................display 8 2;, 9 .................- switches the player on, starts or pauses CD play - stops CD play, clears a program or switches the player off 9 TUNING ∞ , § TUNER : - (down,up) tunes to radio station; CD : - skips and searches CD tracks forwards or backwards. 0 RESUME .............stores the last position of a CD track played HOLD...................locks all buttons OFF......................switches RESUME and HOLD off ! LINE OUT/p........3.5 mm headphone jack and LINE OUT jack to connect the player to another audio input of an additional appliance. @ VOL dj t th l POWER SUPPLY / GENERAL INFORMATION Mains adapter (supplied or optionally available) Use only the AYT 3170 adapter (4.5 V / 300 mA direct current, positive pole to the center pin). Any other product may damage the player. 1 Make sure the local voltage corresponds to the power adapter’s voltage. 2 Connect the power adapter to the 4.5V DC jack of the player and to the wall outlet. Note: Always disconnect the adapter when you are not using it. Environmental information • All redundant packing material has been omitted. We have done our utmost to make the packaging easily separable into two materials: cardboard (box) and polyethylene (bags, protective foam sheet). • Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packing materials, dead batteries and old equipment. GENERAL INFORMATION / CD P In-car use (connections supplied or optionally ava Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 converter (4.5 V DC, positive pole to the center pin) and th adapter. Any other product may damage the set. 1 Put the set on a horizontal, vibration-free and stable surface. Make sure it is in a safe place, where the set is neither a danger nor an obstacle to the driver and the passengers. 2 Plug the voltage converter into the cigarette lighter jack (only for 12 V car battery, negative grounding), then connect the wired end with 4.5V DC input jack on the set. 3 If necessary, clean the cigarette lighter jack to obtain tact. 4 Turn down the volume and connect the cassette adap on the set. 5 Carefully insert the cassette adapter into the car radio’ 6 Make sure the cord does not hinder your driving. 7 Decrease the volume on the set if necessary. Start pl adjust the sound with the car radio controls. IMPORTANT SAFETY INSTRUCTIONS CONSIGNES DE 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat regis- ters, stoves, or other apparatus (including amplifiers) that produce heat. 9. Only use attachments/accessories specified by the manufacturer. 10. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as if the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, or when the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 12. Battery usage CAUTION – To prevent battery leakage which may result in bodily injury, property damage or damage to the unit: G Install ALL batteries correctly, + and - as marked on the unit. G Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.). G Remove batteries when the unit is not used for a long time. EL 6474-E004: 02/8 1. Lisez ces instructions. 2. Conservez ces instructions. 3. Respectez les avertissements. 4. Suivez toutes les instructions. 5. N’utilisez pas cet appareil à proximité d’u 6. Nettoyez l’appareil uniquement avec un ch 7. N’obstruez aucun orifice de ventilation. In selon les instructions du fabricant. 8. N’installez pas l’appareil près d’une sourc comme par exemple des radiateurs, bouches de autres appareils (même des amplificateurs) dégag 9. Utilisez uniquement des accessoires ou op par le fabricant. Return your Warranty Registration card today to ensure you receive all the benefits you’re entitled to. • Once your Philips purchase is regis- tered, you’re eligible to receive all the privileges of owning a Philips product. • So complete and return the Warranty Registration Card enclosed with your purchase at once, and take advantage of these important benefits. Warranty Verification Registering your product within 10 days confirms your right to maximum protection under the terms and conditions of your Philips warranty. Owner Confirmation Your completed Warranty Registration Card serves as verifica- tion of ownership in the event of product theft or loss. Model Registration Returning your Warranty Registration Card right away guarantees you’ll receive all the information and special offers which you qualify for as the owner of your model. This “bolt of lightning” indicates uninsulated material within your unit may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering. The “exclamation point” calls attention to features for which you should read the enclosed litera- ture closely to prevent operating and maintenance problems. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. CAUTION: To prevent electric shock, match wide blade of plug to wide slot, and fully insert. For Customer Use Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference. Model No. _____________________ Serial No. ______________________ Know these safety symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. MAC5097 Renvoyez votre carte d’enregistrement de garantie pour vous assurer de recevoir tous les avantages auxquels vous avez droit. • Dès que l’achat de votre appareil Philips est enregistré, vous avez droit à tous les avantages dont bénéficient les possesseurs des produits Philips. • Remplissez et renvoyez votre carte d’enregistrement de garantie jointe à votre appareil sans tarder et vous béné- ficierez de ces avantages importants. Vérification de garantie Enregistrez votre pro- duit dans les 10 jours pour confirmer votre droit à une protection maximum selon les termes et les conditions de votre garantie Philips. Confirmation de possession Votre carte d’enreg- istrement de garantie prouve que vous pos- sédez l’appareil en cas de vol ou de perte du produit. Enregistrement du modèle Renvoyez votre carte d’enregistrement de garantie dès aujourd’hui pour vous assurer de recevoir toutes les informations, les offres et les bonus auxquels vous avez droit en tant que possesseur de ce modèle. Cet «éclair à pointe de flèche» indique qu’un matériau non isolé, situé à l’intérieur de l’unité, risque de provoquer un choc électrique. Pour la sécurité de chacun, nous vous prions de ne pas retirer le boîtier de ce produit. Le «point d’exclamation» attire votre attention sur des sujets risquant de provoquer des problèmes de fonctionnement et d’entretien si vous ne lisez pas les informations s’y reportant. DANGER : NE PAS EXPOSER CET ÉQUIPEMENT A LA PLUIE NI A UNE HUMIDITÉ EXCESSIVE POUR ÉVITER LES RISQUES D’INCENDIE ET DE CHOC ÉLECTRIQUE. ATTENTION : Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond. Cet espace vous est réservé Inscrivez ci-dessous le numéro de série situé à l’arrière du bloc. Conservez cette information pour vous y reporter à l’avenir. N° de modèle __________________ N° de série ____________________ Connaissez ces symboles de sécurite AT T E N T I O N RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR ATTENTION: POUR REDUIRE LE RESQUE DE CHOC ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE (NI LE PANNEAU ARRIERE). CET APPAREIL NE COMPORTE AUCUNE PIECE POUVANT TRE REPAREE PAR L’UTILISATEUR. CONFIER SON ENTRETIEN A UN TECHNICIEN QUALIFIE. MAC5097 Envie hoy su Tarjeta de Registro de para recibir todas las ventajas corre • Una vez que se registre la compra de su aparato Philips, Ud. tiene derecho a todas las ventajas correspondientes al dueño de un producto Philips. • Sírvase llenar y d la Tarjeta de Reg empacada con s provecho de esta Verificación de la garantía Registre su producto dentro de 10 días para confirmar su derecho a máxima protección bajo los términos y condiciones de la garan- tía de Philips. Confirmación del dueño Su Tarjeta de Registro de la Garantía comprue- ba que Ud. es el dueño del aparato en caso de robo o pérdida del pro- ducto. R de La d de s de que mac mo le c el d El símbolo del «rayo» indica que algún material no aislado dentro de su unidad podría resultar en una sacudida eléctrica. Para la seguridad de todos, favor de no remover la cubierta del producto. El «signo de exclamación» le llama la atención a características sobre las que Ud. debe leer la información adjunta detenidamente para evitar proble- mas de funcionamiento y mantenimiento. ADVERTEN EVITAR EL RIESG ELECTRICA O I EXPONGA EST NI A HUMEDAD PRECAUC sacudida eléctrica ancha del enchufe ancha. Para uso del c Escriba abajo el n encuentra en el p Guarde esta infor No. de modelo No. de serie ___ Conozca estos simbolos de seguridad PRECAUCION RIESGO DE SACUDIDA ELECTRICA NO ABRIR PRECAUCION: PARA REDUCIR EL RIESGO DE SACUDIDA ELECTRICA,NO RETIRE LA CUBIERTA (NI EL PANEL POSTERIOR). ESTE APARATONO CONTIENE NINGUNA PARTE QUE PUEDA SER REPARADA POREL USARIO. DE SER NECESARIO ALGUN SERVICIO O REPARACIONDEL APARATO, LLEVELO UN TECNICO CALIFICADO.

CONTROLS ( see figure 1 ) 1 OPEN 2 ..............opens the CD lid 2 DBB.....................switches the bass enhancement on and off. This button also switches acoustic feedback (the beep) on/off when it is pressed for more than 2 seconds 3 MODE .................selects the different playing possibilities: shuffle, shuffle repeat all, repeat, repeat all and SCAN 4 PROG...................programs CD tracks and radio stations, reviews the program 5 PRESET 3 ,4.....selects a preset tuner station (down, up) 6 FM.......................selects the radio on or off. 7 ............................display 8 2;, 9 .................- switches the player on, starts or pauses CD play - stops CD play, clears a program or switches the player off 9 TUNING ∞ , § TUNER : - (down,up) tunes to radio station; CD : - skips and searches CD tracks forwards or backwards. 0 RESUME .............stores the last position of a CD track played HOLD...................locks all buttons OFF......................switches RESUME and HOLD off ! LINE OUT/p........3.5 mm headphone jack and LINE OUT jack to connect the player to another audio input of an additional appliance. @ VOL E ............adjusts the volume # 4.5V DC...............jack for external power supply $ ............................belt clip holder % ............................type plate POWER SUPPLY / GENERAL INFORMATION Mains adapter (supplied or optionally available) Use only the AYT 3170 adapter (4.5 V / 300 mA direct current, positive pole to the center pin). Any other product may damage the player. 1 Make sure the local voltage corresponds to the power adapter’s voltage. 2 Connect the power adapter to the 4.5V DC jack of the player and to the wall outlet. Note: Always disconnect the adapter when you are not using it. Environmental information • All redundant packing material has been omitted. We have done our utmost to make the packaging easily separable into two materials: cardboard (box) and polyethylene (bags, protective foam sheet). • Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packing materials, dead batteries and old equipment. GENERAL INFORMATION / CD P In-car use (connections supplied or optionally availa Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 1 converter (4.5 V DC, positive pole to the center pin) and the adapter. Any other product may damage the set. 1 Put the set on a horizontal, vibration-free and stable surface. Make sure it is in a safe place, where the set is neither a danger nor an obstacle to the driver and the passengers. 2 Plug the voltage converter into the cigarette lighter jack (only for 12 V car battery, negative grounding), then connect the wired end with 4.5V DC input jack on the set. 3 If necessary, clean the cigarette lighter jack to obtain a tact. 4 Turn down the volume and connect the cassette adapte on the set. 5 Carefully insert the cassette adapter into the car radio’s 6 Make sure the cord does not hinder your driving. 7 Decrease the volume on the set if necessary. Start play adjust the sound with the car radio controls. • Always remove the voltage converter from the cig when the set is not in use. Note: If your car radio has a LINE IN jack, it is better to use car radio connection instead of the cassette.adapter. lead to this LINE IN jack and to LINE OUT/p on the s Playing a CD This CD-player can play all kinds of Audio Discs such as CD-Recordables and CD-Rewritables. Do not try to play a CD-ROM, CDi, VCD, DVD or computer CD. 1 Push the OPEN 2 slider to open the player. 2 Insert an audio CD, printed side up, by pressing the CD onto the hub. 3 Close the player by pressing the lid down. 4 Press 2; to switch the player on and start playback. yThe current track number and elapsed playing time are displayed. • You can pause playback by pressing 2;. yThe time at which playback was paused starts flashing. • You can continue playback by pressing 2; again. 5 Press 9 to stop playback. yThe total number of tracks and the total playing time of the CD are displayed. 6 Press 9 again to switch the player off. CD player and CD handling • Do not touch the lens A of the CD player. • Do not expose the unit, batteries or CDs to humidity, rain, sand or excessive heat (caused by heating equipment or direct sunlight). • You can clean the CD player with a soft, slightly dampened, lint-free cloth. Do not use any cleaning agents as they may have a corrosive effect. • To clean the CD, wipe it in a straight line from the center toward the edge using a soft, lint-free cloth. A cleaning agent may damage the disc! Never write on a CD or attach a sticker to it. • The lens may cloud over when the unit is moved suddenly from cold to warm surroundings. Playing a CD is not possible then. Leave the CD player in a warm environment until the moisture has evaporated. • Active mobile phones in the vicinity of the CD player may cause malfunctions. • Avoid dropping the unit as this may cause damage. Headphones HS383 • Connect the supplied headphones to the LINE OUT/p jack of the player. Note: LINE OUT/p can also be used for connecting this set to your HiFi system.To adjust the sound and volume, use the controls on the connected audio equipment and on the CD player. IMPORTANT! Return your Warranty Registration card today to ensure you receive all the benefits you’re entitled to. • Once your Philips purchase is regis- tered, you’re eligible to receive all the privileges of owning a Philips product. • So complete and return the Warranty Registration Card enclosed with your purchase at once, and take advantage of these important benefits. Warranty Verification Registering your product within 10 days confirms your right to maximum protection under the terms and conditions of your Philips warranty. Owner Confirmation Your completed Warranty Registration Card serves as verifica- tion of ownership in the event of product theft or loss. Model Registration Returning your Warranty Registration Card right away guarantees you’ll receive all the information and special offers which you qualify for as the owner of your model. This “bolt of lightning” indicates uninsulated material within your unit may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering. The “exclamation point” calls attention to features for which you should read the enclosed litera- ture closely to prevent operating and maintenance problems. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. CAUTION: To prevent electric shock, match wide blade of plug to wide slot, and fully insert. For Customer Use Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference. Model No. _____________________ Serial No. ______________________ Know these safety symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. MAC5097 Renvoyez votre carte d’enregistrement de garantie pour vous assurer de recevoir tous les avantages auxquels vous avez droit. • Dès que l’achat de votre appareil Philips est enregistré, vous avez droit à tous les avantages dont bénéficient les possesseurs des produits Philips. • Remplissez et renvoyez votre carte d’enregistrement de garantie jointe à votre appareil sans tarder et vous béné- ficierez de ces avantages importants. Vérification de garantie Enregistrez votre pro- duit dans les 10 jours pour confirmer votre droit à une protection maximum selon les termes et les conditions de votre garantie Philips. Confirmation de possession Votre carte d’enreg- istrement de garantie prouve que vous pos- sédez l’appareil en cas de vol ou de perte du produit. Enregistrement du modèle Renvoyez votre carte d’enregistrement de garantie dès aujourd’hui pour vous assurer de recevoir toutes les informations, les offres et les bonus auxquels vous avez droit en tant que possesseur de ce modèle. Cet «éclair à pointe de flèche» indique qu’un matériau non isolé, situé à l’intérieur de l’unité, risque de provoquer un choc électrique. Pour la sécurité de chacun, nous vous prions de ne pas retirer le boîtier de ce produit. Le «point d’exclamation» attire votre attention sur des sujets risquant de provoquer des problèmes de fonctionnement et d’entretien si vous ne lisez pas les informations s’y reportant. DANGER : NE PAS EXPOSER CET ÉQUIPEMENT A LA PLUIE NI A UNE HUMIDITÉ EXCESSIVE POUR ÉVITER LES RISQUES D’INCENDIE ET DE CHOC ÉLECTRIQUE. ATTENTION : Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond. Cet espace vous est réservé Inscrivez ci-dessous le numéro de série situé à l’arrière du bloc. Conservez cette information pour vous y reporter à l’avenir. N° de modèle __________________ N° de série ____________________ Connaissez ces symboles de sécurite AT T E N T I O N RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR ATTENTION: POUR REDUIRE LE RESQUE DE CHOC ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE (NI LE PANNEAU ARRIERE). CET APPAREIL NE COMPORTE AUCUNE PIECE POUVANT TRE REPAREE PAR L’UTILISATEUR. CONFIER SON ENTRETIEN A UN TECHNICIEN QUALIFIE. MAC5097 Envie hoy su Tarjeta de Registro de l para recibir todas las ventajas corresp • Una vez que se registre la compra de su aparato Philips, Ud. tiene derecho a todas las ventajas correspondientes al dueño de un producto Philips. • Sírvase llenar y de la Tarjeta de Regis empacada con su provecho de estas Verificación de la garantía Registre su producto dentro de 10 días para confirmar su derecho a máxima protección bajo los términos y condiciones de la garan- tía de Philips. Confirmación del dueño Su Tarjeta de Registro de la Garantía comprue- ba que Ud. es el dueño del aparato en caso de robo o pérdida del pro- ducto. Re del La de de su de la que r mació mocio le cor el due El símbolo del «rayo» indica que algún material no aislado dentro de su unidad podría resultar en una sacudida eléctrica. Para la seguridad de todos, favor de no remover la cubierta del producto. El «signo de exclamación» le llama la atención a características sobre las que Ud. debe leer la información adjunta detenidamente para evitar proble- mas de funcionamiento y mantenimiento. ADVERTEN EVITAR EL RIESGO ELECTRICA O IN EXPONGA ESTE NI A HUMEDAD. PRECAUCIO sacudida eléctrica, ancha del enchufe ancha. Para uso del clie Escriba abajo el núm encuentra en el pan Guarde esta inform No. de modelo _ No. de serie ____ Conozca estos simbolos de seguridad PRECAUCION RIESGO DE SACUDIDA ELECTRICA NO ABRIR PRECAUCION: PARA REDUCIR EL RIESGO DE SACUDIDA ELECTRICA,NO RETIRE LA CUBIERTA (NI EL PANEL POSTERIOR). ESTE APARATONO CONTIENE NINGUNA PARTE QUE PUEDA SER REPARADA POREL USARIO. DE SER NECESARIO ALGUN SERVICIO O REPARACIONDEL APARATO, LLEVELO UN TECNICO CALIFICADO. Batteries (supplied or optionally available) You can use the following batteries with this CD-player: • normal batteries type LR6, UM3 or AA (preferably Philips), or • alkaline batteries type LR6, UM3 or AA (preferably Philips). Notes:– Old and new or different types of batteries should not be combined. – Remove batteries if they are empty or if the player is not going to be used for a long time. Inserting batteries 1 Push OPEN 2 to open the CD lid. 2 Open the battery compartment and insert either 2 normal or alkaline batteries. Battery indication The approximate power level of your batteries is shown in the display. Battery full Battery two-thirds full Battery one-third full Battery dead or empty. When the batteries are dead or empty, the symbol flashes, bAtt is displayed, and the beep tone sounds repeatedly.

One Year Free Exchange This product must be carried in for an exchange. LIMITED WARRANTY WHO IS COVERED? You must have proof of purchase to exchange the product.A sales receipt or other doc- ument showing that you purchased the product is considered proof of purchase.Attach it to this owner’s manual and keep both nearby. WHAT IS COVERED? Warranty coverage begins the day you buy your product. For one year thereafter, a defective or inoperative product will be replaced with a new, renewed or comparable product at no charge to you.A replacement product is covered only for the original war- ranty period.When the warranty on the original product expires, the warranty on the replacement product also expires. WHAT IS EXCLUDED? Your warranty does not cover: • labor charges for installation or setup of the product, adjustment of customer controls on the product, and installation or repair of antenna systems outside of the product. • product repair and/or part replacement because of misuse, accident, unauthorized repair or other cause not within the control of Philips. • reception problems caused by signal conditions or cable or antenna systems outside the unit. • a product that requires modification or adaptation to enable it to operate in any coun- try other than the country for which it was designed, manufactured, approved and/or authorized, or repair of products damaged by these modifications. • incidental or consequential damages resulting from the product. (Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.This includes, but is not limited to, prerecorded material, whether copyrighted or not copyrighted.) • a product that is used for commercial or institutional purposes. WHERE IS EXCHANGE AVAILABLE? You may exchange the product in all countries where the product is officially distributed by Philips. In countries where Philips does not distribute the product, the local Philips service organization will attempt to provide a replacement product (although there may be a delay if the appropriate product is not readily available). Philips, P.O. Box 520890, Miami, FL 33152, USA, (402) 536-4171 EL4967E007 / 8-02 BEFORE REQUESTING EXCHANGE... Please check your owner's manual for assistance. If you have additional questions, call us at 1-800-531-0039. EXCHANGING A PRODUCT IN U.S.A., PUERTO RICO, OR U.S.VIRGIN ISLANDS... Contact 1-800-531-0039 to arrange an exchange. Or, ship the product, insured and freight prepaid, and with proof of purchase enclosed, to the address listed below. Philips Exchange Program Suite A 406 North Irish Street Greeneville TN 37745 (In U.S.A., Puerto Rico, and U.S.Virgin Islands, all implied warranties, including implied war- ranties of merchantability and fitness for a particular purpose, are limited in duration to the duration of this express warranty. But, because some states do not allow limitations on how long an implied warranty may last, this limitation may not apply to you.) EXCHANGING A PRODUCT IN CANADA... Please contact Philips at: 1-800-661-6162 (French Speaking) 1-800-531-0039 (English or Spanish Speaking) (In Canada, this warranty is given in lieu of all other warranties. No other warranties are expressed or implied, including any implied warranties of merchantability or fitness for a particular purpose. Philips is not liable under any circumstances for any direct, indirect, special, incidental or consequential damages, howsoever incurred, even if notified of the possibility of such damages.) REMEMBER... Please record below the model and serial numbers found on the product.Also, please fill out and mail your warranty registration card promptly. It will be easier for us to notify you if necessary. MODEL # ____________________________________ SERIAL # ____________________________________ This warranty gives you specific legal rights.You may have other rights which vary from state/province to state/province. FEATURES / TROUBLESHOOTING e headphone wire is used as an FM antenna. ecessary, move it for optimum reception. oring radio stations can store up to 30 radio stations (1-30). Tune to a desired radio station and press PROG. Press PRESET3 ,4 repeatedly if necessary to select the number that should be assigned to this radio station. Press PROG while PRESET is blinking to confirm the storage. yPRESET, the waveband, the frequency and the preset number of the stored station are displayed. Store all desired stations this way. te: Already stored stations can be recognized by the indicator PRESET and the preset number. ntennas

CONTROLS ( see figure 1 ) 1 OPEN 2 ..............opens the CD lid 2 DBB.....................switches the bass enhancement on and off. This button also switches acoustic feedback (the beep) on/off when it is pressed for more than 2 seconds 3 MODE .................selects the different playing possibilities: shuffle, shuffle repeat all, repeat, repeat all and SCAN 4 PROG...................programs CD tracks and radio stations, reviews the program 5 PRESET 3 ,4.....selects a preset tuner station (down, up) 6 FM.......................selects the radio on or off. 7 ............................display 8 2;, 9 .................- switches the player on, starts or pauses CD play - stops CD play, clears a program or switches the player off 9 TUNING ∞ , § TUNER : - (down,up) tunes to radio station; CD : - skips and searches CD tracks forwards or backwards. 0 RESUME .............stores the last position of a CD track played HOLD...................locks all buttons OFF......................switches RESUME and HOLD off ! LINE OUT/p........3.5 mm headphone jack and LINE OUT jack to connect the player to another audio input of an additional appliance. @ VOL E ............adjusts the volume # 4.5V DC...............jack for external power supply $ ............................belt clip holder % ............................type plate POWER SUPPLY / GENERAL INFORMATION Mains adapter (supplied or optionally available) Use only the AYT 3170 adapter (4.5 V / 300 mA direct current, positive pole to the center pin). Any other product may damage the player. 1 Make sure the local voltage corresponds to the power adapter’s voltage. 2 Connect the power adapter to the 4.5V DC jack of the player and to the wall outlet. Note: Always disconnect the adapter when you are not using it. Environmental information • All redundant packing material has been omitted. We have done our utmost to make the packaging easily separable into two materials: cardboard (box) and polyethylene (bags, protective foam sheet). • Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packing materials, dead batteries and old equipment. GENERAL INFORMATION / CD P In-car use (connections supplied or optionally avail Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 1 converter (4.5 V DC, positive pole to the center pin) and the adapter. Any other product may damage the set. 1 Put the set on a horizontal, vibration-free and stable surface. Make sure it is in a safe place, where the set is neither a danger nor an obstacle to the driver and the passengers. 2 Plug the voltage converter into the cigarette lighter jack (only for 12 V car battery, negative grounding), then connect the wired end with 4.5V DC input jack on the set. 3 If necessary, clean the cigarette lighter jack to obtain a tact. 4 Turn down the volume and connect the cassette adapt on the set. 5 Carefully insert the cassette adapter into the car radio’s 6 Make sure the cord does not hinder your driving. 7 Decrease the volume on the set if necessary. Start pla adjust the sound with the car radio controls. • Always remove the voltage converter from the cig when the set is not in use. Note: If your car radio has a LINE IN jack, it is better to use car radio connection instead of the cassette.adapter. lead to this LINE IN jack and to LINE OUT/p on the s Playing a CD This CD-player can play all kinds of Audio Discs such as CD-Recordables and CD-Rewritables. Do not try to play a CD-ROM, CDi, VCD, DVD or computer CD. 1 Push the OPEN 2 slider to open the player. 2 Insert an audio CD, printed side up, by pressing the CD onto the hub. 3 Close the player by pressing the lid down. 4 Press 2; to switch the player on and start playback. yThe current track number and elapsed playing time are displayed. • You can pause playback by pressing 2;. yThe time at which playback was paused starts flashing. • You can continue playback by pressing 2; again. 5 Press 9 to stop playback. yThe total number of tracks and the total playing time of the CD are displayed. 6 Press 9 again to switch the player off. • To remove the CD, hold it by its edge and press the hub gently while lifting the CD. Note: If there is no activity, the set will automatically switch off after a while to save energy. CD player and CD handling • Do not touch the lens A of the CD player. • Do not expose the unit, batteries or CDs to humidity, rain, sand or excessive heat (caused by heating equipment or direct sunlight). • You can clean the CD player with a soft, slightly dampened, lint-free cloth. Do not use any cleaning agents as they may have a corrosive effect. • To clean the CD, wipe it in a straight line from the center toward the edge using a soft, lint-free cloth. A cleaning agent may damage the disc! Never write on a CD or attach a sticker to it. • The lens may cloud over when the unit is moved suddenly from cold to warm surroundings. Playing a CD is not possible then. Leave the CD player in a warm environment until the moisture has evaporated. • Active mobile phones in the vicinity of the CD player may cause malfunctions. • Avoid dropping the unit as this may cause damage. Headphones HS383 • Connect the supplied headphones to the LINE OUT/p jack of the player. Note: LINE OUT/p can also be used for connecting this set to your HiFi system.To adjust the sound and volume, use the controls on the connected audio equipment and on the CD player. IMPORTANT! Hearing safety: Do not play your headphones at a high volume. Hearing experts advise that continuous use at high volume can permanently damage your hearing. Traffic safety: Do not use headphones while driving a vehicle. It may create a hazard and it is illegal in many countries. Even if your headphones are an open-air type designed to let you hear outside sounds, do not turn up the volume so high that you cannot hear what is going on around you. Batteries (supplied or optionally available) You can use the following batteries with this CD-player: • normal batteries type LR6, UM3 or AA (preferably Philips), or • alkaline batteries type LR6, UM3 or AA (preferably Philips). Notes:– Old and new or different types of batteries should not be combined. – Remove batteries if they are empty or if the player is not going to be used for a long time. Inserting batteries 1 Push OPEN 2 to open the CD lid. 2 Open the battery compartment and insert either 2 normal or alkaline batteries. Battery indication The approximate power level of your batteries is shown in the display. Battery full Battery two-thirds full Battery one-third full Battery dead or empty. When the batteries are dead or empty, the symbol flashes, bAtt is displayed, and the beep tone sounds repeatedly. Average playing time of batteries under normal conditions Battery type ESP on Power Save Normal 5 hours 6 hours Alkaline 16 hours 20 hours Batteries contain chemical substances, so they should be disposed of properly.

In-car use (connections supplied or optionally available) Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 118 71890) car voltage converter (4.5 V DC, positive pole to the center pin) and the AY 3501 cassette car adapter. Any other product may damage the set. 1 Put the set on a horizontal, vibration-free and stable surface. Make sure it is in a safe place, where the set is neither a danger nor an obstacle to the driver and the passengers. 2 Plug the voltage converter into the cigarette lighter jack (only for 12 V car battery, negative grounding), then connect the wired end with 4.5V DC input jack on the set. 3 If necessary, clean the cigarette lighter jack to obtain a good electrical con- tact. 4 Turn down the volume and connect the cassette adapter plug to LINE OUT/p on the set. 5 Carefully insert the cassette adapter into the car radio’s cassette compartment. 6 Make sure the cord does not hinder your driving. 7 Decrease the volume on the set if necessary. Start playback on the set and adjust the sound with the car radio controls. • Always remove the voltage converter from the cigarette lighter jack- when the set is not in use. Note: If your car radio has a LINE IN jack, it is better to use it for the car radio connection instead of the cassette.adapter. Connect the signal lead to this LINE IN jack and to LINE OUT/p on the set. CD PLAY / FEATURES Playback information • If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded properly, nF dISC is displayed, indicating that the CD has not been finalized. In that case, use FINALIZE on your CD recorder to complete the recording. • When playing a CD-Rewritable (CD-RW), please note that it takes 3–15 seconds after pressing 2; for sound reproduction to start. • Playback will stop if you open the CD lid. • While the CD is read, 1 -:- flashes in the display. Volume and bass Volume adjustment • Adjust the volume by using VOL E. Bass adjustment • Press DBB to switch the bass enhancement on or off y is shown if the bass enhancement is activated. DBB FEATURES Programming track numbers You can store up to 30 tracks to play in a program. A single track may be stored more than once in the program. 1 While playback is stopped, select a track with ∞or §. 2 Press PROG to store the track. yprogram lights up; the track number programmed and P with the total number of stored tracks are displayed. 3 Select and store all desired tracks in this way. 4 Press 2; to start playback of your selected tracks. yprogram is shown and playback starts. • You can review the program by pressing PROG for more than 2 seconds. yThe display shows all the stored tracks in sequence. Notes: – If you press PROG and there is no track selecte displayed. – If you try to store more than 30 tracks, FULL Clearing the program • While playback is stopped, press 9 to clear program. yCLR is displayed once, program goes off, and the program is cleared. Note: The program will also be cleared if the power supply is interrupted, or if the CD-player lid is opened, or if the set switches off automatically. Selecting different playing possibilities−MODE It is possible to play tracks in random order, to repeat a single track or the entire CD, and to play the first few seconds of each track. 1 Press MODE during playback as often as required in order to activate one of the following ‘modes’. The active mode is shown in the display. yshuffle : All tracks of the CD are played in random order until all of them have been played onc yshuffle repeat all : All tracks of the CD are played repeatedly in random order. yrepeat : The current track is played repeatedly. yrepeat all : The entire CD is played repeatedly. ySCAN: The first 10 seconds of each of the remain- ing tracks are played in sequence. 2 Playback starts in the chosen mode after 2 seconds. • To return to normal playback, press MODE repeatedly no active modes. ESP / Power Save Mode With a conventional portable CD-player you might have ex music stopped e.g. when you were jogging. The ELECTRO prevents loss of sound caused by light vibrations and shoc is ensured. However ESP does not prevent playback interr running. It also does not protect the unit against any dam On this set ESP is default on. It is possible to set ESP off a Save mode. The Power Save mode helps to extend battery lifetime for longer playback. • Press MODE for more than 2 seconds. y disappears. power save modeis now activa • Press MODE again for more than 2 seconds. y is displayed once Selecting a track and searching Selecting a track during playback • Briefly press ∞ or § once or several times to skip to the current, previous or next track. yPlayback continues with the selected track, and the track’s number is displayed. Selecting a track when playback is stopped 1 Briefly press ∞ or § once or several times to select the desired track. The track number is displayed. 2 Press 2; to start CD play. yPlayback starts with the selected track. Searching for a passage during playback 1 Keep ∞ or § pressed to find a particular passage in a backward or forward direction. ySearching starts while playback continues at low volume. After 2 seconds the search speeds up. 2 Release the button when you reach the desired passage. yPlayback continues from this position. Notes: – If the player is in SCAN mode (see MODE chapter), searching is not possible. Playing a CD This CD-player can play all kinds of Audio Discs such as CD-Recordables and CD-Rewritables. Do not try to play a CD-ROM, CDi, VCD, DVD or computer CD. 1 Push the OPEN 2 slider to open the player. 2 Insert an audio CD, printed side up, by pressing the CD onto the hub. 3 Close the player by pressing the lid down. 4 Press 2; to switch the player on and start playback. yThe current track number and elapsed playing time are displayed. • You can pause playback by pressing 2;. yThe time at which playback was paused starts flashing. • You can continue playback by pressing 2; again. 5 Press 9 to stop playback. yThe total number of tracks and the total playing time of the CD are displayed. 6 Press 9 again to switch the player off. • To remove the CD, hold it by its edge and press the hub gently while lifting the CD. Note: If there is no activity, the set will automatically switch off after a while to save energy.

You can store up to 30 tracks to play in a program. A single track may be stored more than once in the program. 1 While playback is stopped, select a track with ∞or §. 2 Press PROG to store the track. yprogram lights up; the track number programmed and P with the total number of stored tracks are displayed. 3 Select and store all desired tracks in this way. 4 Press 2; to start playback of your selected tracks. yprogram is shown and playback starts. • You can review the program by pressing PROG for more than 2 seconds. yThe display shows all the stored tracks in sequence. Notes: – If you press PROG and there is no track selected, SEL is displayed. – If you try to store more than 30 tracks, FULL is displayed. Clearing the program • While playback is stopped, press 9 to clear program. yCLR is displayed once, program goes off, and the program is cleared. Note: The program will also be cleared if the power supply is interrupted, or if the CD-player lid is opened, or if the set switches off automatically. FEATURES RESUME and HOLD You can interrupt playback and continue (even after an extended period of time) from the position where playback stopped (RESUME) and you can lock all buttons of the set so that no action will be executed (HOLD). Use the RESUME–HOLD–OFF slider for these functions. RESUME – continuing from where you have stopped 1 Switch the slider to RESUME during playback to activate RESUME. yresume is shown. 2 Press 9 whenever you want to stop playback. 3 Press 2; whenever you want to resume playback. yresume is shown and playback continues from where you have stopped. • To deactivate RESUME, switch the slider to OFF. yresume goes off. HOLD – locking all buttons You can lock the buttons of the set by switching the slider to HOLD. Now, when a key is pressed, no action will be executed. This is of use, for example, when transporting the player in a bag. With HOLD activated, you can avoid accidental activation of other functions. 1 Switch the slider to HOLD to activate HOLD. yAll buttons are locked. HoLd is shown when you press any button. If the set is switched off, hold will be shown only when 2; or FM is pressed. 2 To deactivate HOLD, switch the slider to OFF. Note: If you deactivate HOLD by switching the slider to RESUME, you will be activating the RESUME function. Troubleshooting WARNING: Under no circumstances should you try to re this will invalidate the warranty. If a fault occurs, first che before taking the unit for repair. If you are unable to solv these hints, consult your dealer or service center. The CD player has no power, or playback does not s • Check that your batteries are not dead or empty, that correctly, that the contact pins are clean. • Your adapter connection may be loose. Connect it sec • For in-car use, check that the car ignition is on. Also c The indication no diSC is displayed • Check that the CD is clean and correctly inserted (labe • If your lens has steamed up, wait a few minutes for th The indication nF diSC is displayed • CD-RW (CD-R) was not recorded properly. Use FINALIZ The indication HOLD is on and/or there is no reactio • If HOLD is activated, then deactivate it. • Electrostatic discharge. Disconnect power or remove ba The CD skips tracks • The CD is damaged or dirty. Replace or clean the CD. • RESUME, SHUFFLE or PROGRAM is active. Switch off No sound or bad sound quality. • PAUSE might be active. Press 2;. • Loose, wrong or dirty connections. Check and clean co • Volume might not be appropriately adjusted. Adjust th • Strong magnetic fields. Check player’s position and co away from active mobile phones. • For in-car use, check that the cassette adapter is inser cassette player’s playback direction is correct (press au and that the cigarette lighter jack is clean. Allow time Selecting different playing possibilities−MODE It is possible to play tracks in random order, to repeat a single track or the entire CD, and to play the first few seconds of each track. 1 Press MODE during playback as often as required in order to activate one of the following ‘modes’. The active mode is shown in the display. yshuffle : All tracks of the CD are played in random order until all of them have been played once. yshuffle repeat all : All tracks of the CD are played repeatedly in random order. yrepeat : The current track is played repeatedly. yrepeat all : The entire CD is played repeatedly. ySCAN: The first 10 seconds of each of the remain- ing tracks are played in sequence. 2 Playback starts in the chosen mode after 2 seconds. • To return to normal playback, press MODE repeatedly until the display shows no active modes. ESP / Power Save Mode With a conventional portable CD-player you might have experienced that the music stopped e.g. when you were jogging. The ELECTRONIC SKIP PROTECTION prevents loss of sound caused by light vibrations and shocks. Continuous playback is ensured. However ESP does not prevent playback interruptions during vigorous running. It also does not protect the unit against any damage caused by dropping! On this set ESP is default on. It is possible to set ESP off and enter the Power Save mode. The Power Save mode helps to extend battery lifetime for longer playback. • Press MODE for more than 2 seconds. y disappears. power save modeis now activated. • Press MODE again for more than 2 seconds. y is displayed once Radio Play You can tune to any FM station automatically or manually. 1 Press FM to switch the radio on. Tuning to radio stations automatically 1 Keep ∞or § pressed for at least 2 second. yThe radio tunes to a station with sufficient strength and radio play starts. The current waveband and frequency are displayed. 2 Repeat searching until you find the desired radio station. Tuning to radio stations manually 1 Keep ∞or § pressed. 2 Release ∞or §, then briefly press ∞or § again when you are close to the desired frequency. 3 Briefly press ∞or § repeatedly until you reach the desired frequency. yRadio play starts. The current waveband and frequency are displayed. • To switch from radio play to CD play, press 2; . • Press FM or 9 to switch the radio off. FEATURES / TROUBLESHOOT The headphone wire is used as an FM antenna. If necessary, move it for optimum reception. Storing radio stations You can store up to 30 radio stations (1-30). 1 Tune to a desired radio station and press PROG. 2 Press PRESET3 ,4 repeatedly if necessary to select the number that should be assigned to this radio station. 3 Press PROG while PRESET is blinking to confirm the storage. yPRESET, the waveband, the frequency and the preset number of the stored station are displayed. 4 Store all desired stations this way. Note: Already stored stations can be recognized by the indicator PRESET and the preset number. Tuning to a stored radio station 1 Press FM to switch the radio ON. 2 Press PRESET3 ,4 once or more to find your preset st yRadio play starts. program, the waveband, the preset number of the stored station are displayed Antennas

this will invalidate the warranty. If a fault occurs, first check the points listed, before taking the unit for repair. If you are unable to solve a problem by following these hints, consult your dealer or service center. The CD player has no power, or playback does not start • Check that your batteries are not dead or empty, that they are inserted correctly, that the contact pins are clean. • Your adapter connection may be loose. Connect it securely. • For in-car use, check that the car ignition is on. Also check player’s batteries. The indication no diSC is displayed • Check that the CD is clean and correctly inserted (label-side upward). • If your lens has steamed up, wait a few minutes for this to clear. The indication nF diSC is displayed • CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder. The indication HOLD is on and/or there is no reaction to controls • If HOLD is activated, then deactivate it. • Electrostatic discharge. Disconnect power or remove batteries for a few seconds. The CD skips tracks • The CD is damaged or dirty. Replace or clean the CD. • RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on. No sound or bad sound quality. • PAUSE might be active. Press 2;. • Loose, wrong or dirty connections. Check and clean connections. • Volume might not be appropriately adjusted. Adjust the volume. • Strong magnetic fields. Check player’s position and connections. Also keep away from active mobile phones. • For in-car use, check that the cassette adapter is inserted correctly, that the car cassette player’s playback direction is correct (press autoreverse to change), and that the cigarette lighter jack is clean. Allow time for temperature change. FEATURES / TROUBLESHOOTING The headphone wire is used as an FM antenna. If necessary, move it for optimum reception. Storing radio stations You can store up to 30 radio stations (1-30). 1 Tune to a desired radio station and press PROG. 2 Press PRESET3 ,4 repeatedly if necessary to select the number that should be assigned to this radio station. 3 Press PROG while PRESET is blinking to confirm the storage. yPRESET, the waveband, the frequency and the preset number of the stored station are displayed. 4 Store all desired stations this way. Note: Already stored stations can be recognized by the indicator PRESET and the preset number. Tuning to a stored radio station 1 Press FM to switch the radio ON. 2 Press PRESET3 ,4 once or more to find your preset station. yRadio play starts. program, the waveband, the frequency and the preset number of the stored station are displayed. Antennas

1 OPEN 2 3 CD 5 HOLD➟OFF 6 PLAY 7 VOLUME AA LR6 UM3 !!! 2. 1. 1. 4 0 VOL. RE M SU OFF • E • L H O D LIN E OU T/ DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGITAL FM TUNER DIGITAL FM TUNER DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGIT DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PRESET DIGITAL FM TUNER 45 S ECO ND S E LEC TR ON IC SKI P P RO TE CT IO N C D RE W RI TA BL E C O M PA TI BL E 45 S EC ONDS E LEC TRO NIC SKI P P ROT ECT ION CD RE WR IT AB LE C O M P A TI B L E # % $ 1 2 3 4 5 7 8 9 @ DIGITAL DYNAMIC BASS BOOST CD TUNING DBB MODE PROG DIGITAL FM TUNER 45 S ECO NDS ELE CT RO NIC SKI P P RO TE CT IO N C D RE W RI TA BL E C O M PA TI BL E ! 0 6 PRESET English Français Español English CONTROLS / POWER SUPPLY CONTROLS ( see figure 1 ) 1 OPEN 2 ..............opens the CD lid 2 DBB.....................switches the bass enhancement on and off. This button also switches acoustic feedback (the beep) on/off when it is pressed for more than 2 seconds 3 MODE .................selects the different playing possibilities: shuffle, shuffle repeat all, repeat, repeat all and SCAN 4 PROG...................programs CD tracks and radio stations, reviews the program 5 PRESET 3 ,4.....selects a preset tuner station (down, up) 6 FM.......................selects the radio on or off. 7 ............................display 8 2;, 9 .................- switches the player on, starts or pauses CD play - stops CD play, clears a program or switches the player off 9 TUNING ∞ , § TUNER : - (down,up) tunes to radio station; CD : - skips and searches CD tracks forwards or backwards. 0 RESUME .............stores the last position of a CD track played HOLD...................locks all buttons OFF......................switches RESUME and HOLD off ! LINE OUT/p........3.5 mm headphone jack and LINE OUT jack to connect the player to another audio input of an additional appliance. @ VOL E ............adjusts the volume # 4.5V DC...............jack for external power supply $ ............................belt clip holder % ............................type plate POWER SUPPLY / GENERAL INFO Mains adapter (supplied or optionally available) Use only the AYT 3170 adapter (4.5 V / 300 mA direct current, positive pole to the center pin). Any other produ may damage the player. 1 Make sure the local voltage corresponds to the pow adapter’s voltage. 2 Connect the power adapter to the 4.5V DC jack of t player and to the wall outlet. Note: Always disconnect the adapter when you are no Environmental information • All redundant packing material has been omitted. W make the packaging easily separable into two mate polyethylene (bags, protective foam sheet). • Your set consists of materials which can be recycle specialized company. Please observe the local regu disposal of packing materials, dead batteries and o CD player and CD handling • Do not touch the lens A of the CD player. • Do not expose the unit, batteries or CDs to humidity rain, sand or excessive heat (caused by heating equipment or direct sunlight). • You can clean the CD player with a soft, slightly dampened, lint-free cloth. Do not use any cleaning agents as they may have a corrosive effect. • To clean the CD, wipe it in a straight line from the center toward the edge using a soft, lint-free cloth. damage the disc! Never write on a CD or attach a s • The lens may cloud over when the unit is moved su surroundings. Playing a CD is not possible then. Lea environment until the moisture has evaporated. • Active mobile phones in the vicinity of the CD playe • Avoid dropping the unit as this may cause damage. Headphones HS383 • Connect the supplied headphones to the LINE OUT/ jack of the player. Note: LINE OUT/p can also be used for connecting this set to your HiFi system.To adjust th sound and volume, use the controls on the connecte audio equipment and on the CD player. Return your Warranty Registration card today to ensure you receive all the benefits you’re entitled to. • Once your Philips purchase is regis- tered, you’re eligible to receive all the privileges of owning a Philips product. • So complete and return the Warranty Registration Card enclosed with your purchase at once, and take advantage of these important benefits. Warranty Verification Registering your product within 10 days confirms your right to maximum protection under the terms and conditions of your Philips warranty. Owner Confirmation Your completed Warranty Registration Card serves as verifica- tion of ownership in the event of product theft or loss. Model Registration Returning your Warranty Registration Card right away guarantees you’ll receive all the information and special offers which you qualify for as the owner of your model. This “bolt of lightning” indicates uninsulated material within your unit may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering. The “exclamation point” calls attention to features for which you should read the enclosed litera- ture closely to prevent operating and maintenance problems. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. CAUTION: To prevent electric shock, match wide blade of plug to wide slot, and fully insert. For Customer Use Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference. Model No. _____________________ Serial No. ______________________ Know these safety symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. MAC5097 Renvoyez votre carte d’enregistrement de assurer de recevoir tous les avantages auxq • Dès que l’achat de votre appareil Philips est enregistré, vous avez droit à tous les avantages dont bénéficient les possesseurs des produits Philips. • Remplissez e d’enregistrem votre appare ficierez de ce Vérification de garantie Enregistrez votre pro- duit dans les 10 jours pour confirmer votre droit à une protection maximum selon les termes et les conditions de votre garantie Philips. Confirmation de possession Votre carte d’enreg- istrement de garantie prouve que vous pos- sédez l’appareil en cas de vol ou de perte du produit. Cet «éclair à pointe de flèche» indique qu’un matériau non isolé, situé à l’intérieur de l’unité, risque de provoquer un choc électrique. Pour la sécurité de chacun, nous vous prions de ne pas retirer le boîtier de ce produit. Le «point d’exclamation» attire votre attention sur des sujets risquant de provoquer des problèmes de fonctionnement et d’entretien si vous ne lisez pas les informations s’y reportant. DANGER ÉQUIPEMENT HUMIDITÉ EX RISQUES D’IN ÉLECTRIQUE. ATTENT chocs électriq plus large de correspondan jusqu’au fond Cet espace Inscrivez ci-des situé à l’arrière information po N° de modè N° de série Connaissez ces symboles de sécurite AT T E N T I O N RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR ATTENTION: POUR REDUIRE LE RESQUE DE CHOC ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE (NI LE PANNEAU ARRIERE). CET APPAREIL NE COMPORTE AUCUNE PIECE POUVANT TRE REPAREE PAR L’UTILISATEUR. CONFIER SON ENTRETIEN A UN TECHNICIEN QUALIFIE. QUICK START MISE EN SERVICE RAPIDE ENCENDIDO RAPIDO PHILIPS CONSUMER ELECTRONICS NORTH AMERICA Knoxville, Tennessee 37914-1810, U.S.A. Batteries (supplied or optionally available) You can use the following batteries with this CD-player: • normal batteries type LR6, UM3 or AA (preferably Philips), or • alkaline batteries type LR6, UM3 or AA (preferably Philips). Notes:– Old and new or different types of batteries should not be combined. – Remove batteries if they are empty or if the player is not going to be used for a long time. Inserting batteries 1 Push OPEN 2 to open the CD lid. 2 Open the battery compartment and insert either 2 normal or alkaline batteries. Battery indication The approximate power level of your batteries is shown in the display. Battery full Battery two-thirds full Battery one-third full Battery dead or empty. When the batteries are dead or empty, the symbol flashes, bAtt is displayed, and the beep tone sounds repeatedly. Meet Philips at the Internet http://www.philips.com 1 AZT3200, AZT3201, AZT3202 3140 115 3065.1