Philips 43PP9202 Quick Use And Setup Manual

using a cable TV or antenna signal. If you have cable TV service, you’ll simply connect the coaxial cable lead-in from the cable TV company to your TV. If you intend to connect a VHF/UHF antenna, you may need a 300- to 75-ohm adapter, which is not supplied with your TV. NOTE: You should be able to buy optional accessories such as a VHF/UHF antenna or a 300- to 75-ohm adapter at most stores that sell electronics. Or you can call our Customer Care Center at 1-800-531-0039. 1 Connect the Cable TV or antenna signal to the ANTENNA IN 75Ωjack on the rear of the TV. NOTE: If you are using an antenna with a round coaxial cable (75Ω), then you are ready to connect to the back of the TV. If your antenna has a flat, twin-lead wire (300Ω), you must first attach the antenna wires on a 300- to 75- ohm adapter. Then push the round end of the adapter onto the ANTENNA IN 75Ωjack on the rear of the TV. 2 Insert the TV’s power plug into the wall power outlet. 3135 035 20401 Rear-projection HDTV Monitor Rear-projection HDTV Monitor Quick Use and Setup Guide Quick Use and Setup Guide MAKING BASIC TV CONNECTIONS Twin-lead Wire 300- to 75-ohm Adapter OR Coaxial Cable Lead-in from Antenna Cable TV Company Rear of TV Coaxial Cable Coaxial Cable Lead-in from Cable TV Company Outdoor or Indoor Antenna (Combination VHF/UHF) VIDEO S-VIDEO L Pb Pr VIDEO S-VIDEO L AUDIO L R AUDIO L R G/Y R/Pr B/Pb V H SYNC L R AUDIO HD INPUT-AV 4 INPUT-AV 2 OUTPUT INPUT-AV 1 ANTENNA IN 75Ω Y The combination antenna receives normal broadcast channels 2-13 (VHF) and 14-69 (UHF). 1 CONTENTS Important Notice/Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Making Basic TV Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–2 Operating the Television and Remote Control . . . . . . . . . . . . . . . . . . . . . . . . .2–3 Using the Installation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4–6 Using the Picture-in-Picture (PIP) Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . .6–7 Adjusting the Manual Converge Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 ANTENNA OR CABLE TV BEST VIEWING T he major benefit of this projection television is its large view- ing screen. To see this large screen at its best, test various locations in the room to find the optimal spot for viewing. NOTE: Be sure to allow a free flow of air to and from the per- forated back cover of the set. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot—for example, in direct sunlight or near a heating appliance. Magnetic fields, such as those of external speak- ers, may cause the picture to distort if the speak- ers are placed too close to the television. Move the magnetic field source away from the TV until there is no picture distortion. CABLES AND CONNECTORS I f you are new to making TV hookups, you may want to read this section. (The cables and connectors discussed are not sup- plied with your set. You can buy them at most stores that sell audio or video products. Or call our Customer Care Center at 1-800-531-0039.) This publication provides you with examples of basic connections. See pages 6–15 in the Directions for Use manual for more infor- mation and connection examples. A 75-ohm coaxial cable connects signals from an antenna or a cable TV company to the antenna jack on the back of the TV. Coaxial cables use “F” connectors. A two-way signal splitter enables you to take a single antenna or cable TV signal and supply it to two different inputs. A 300- to 75-ohm twin-lead adapter accepts the antenna cables (called twin-lead wires) from an antenna, allowing you to connect the antenna signal to the TV. Video and audio cables with standard RCA (phono) connectors con- nect the video and audio jacks of accessory devices such as VCRs and DVD players to the jacks on the TV. To simplify making connections, the connectors are usually color coded. The jacks on your TV are likewise color coded to match the colors of the connectors. The coding is as follows: yellow for video (composite) and red and white for the right and left audio channels, respectively. Use an audio cable with a white connector when making mono, or nonstereo, connections. The connectors of video cables used to connect component video or RGB (high-resolution) jacks are often color coded red, green, and blue. Component video connec- tions provide you with the highest possible color and picture resolution. An S-Video cable connects devices such as DVD players, VCRs, or camcorders to your TV. S-Video provides better picture performance than regular (composite) video connections. S- Video cables can be used only with S-Video-com- patible accessory devices. As an Energy Star® Partner, Philips Consumer Electronics has determined this product meets the Energy Star® guidelines for energy efficiency. Energy Star® is a U.S. registered mark. Using products with the Energy Star® label can save energy. Saving energy reduces air pollution and lowers utility bills. IMPORTANT This owner's manual is used with several differ- ent television models. Not all features (and draw- ings) discussed in this manual will necessarily match those found with your television set. This is normal and does not require that you contact your dealer or request service. WARNING: TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS UNIT TO RAIN OR EXCESSIVE MOISTURE.

TELEVISION SOURCE SELECT > ? +A -A VOL CH MENU You can press any of the buttons on the front of the TV to turn the TV on, but you must press the Power/Standby button to turn the set off. HELPFUL HINT REMOTE CONTROL TV SWAP PIP CH DN UP FREEZE SOUND POWER PICTURE VCR ACC ACTIVE CONTROL MAKING BASIC TV CONNECTIONS (CONTINUED) INPUT OUTPUT Cable Converter Box Rear of TV Coaxial Cable Lead-in from Cable TV Company VIDEO S-VIDEO L Pb Pr VIDEO S-VIDEO L AUDIO L R AUDIO L R G/Y R/Pr B/Pb V H SYNC L R AUDIO HD INPUT-AV 4 INPUT-AV 2 OUTPUT INPUT-AV 1 ANTENNA IN 75Ω Y 1 2 Coaxial Cable (Not Supplied) F ollow the steps below to connect a cable converter box to your TV. To make the connections in this example, you will need one coaxi- al cable (75Ω). NOTE: The coaxial cable is not supplied with your TV. You should be able to buy one at most stores that sell electronics. Or you can call our Customer Care Center at 1-800-531-0039. 1 Connect your cable TV signal to the INPUT jack on the back of the cable converter box. 2 Connect a coaxial cable from the OUTPUT jack on the back of the cable converter box to the ANTENNA IN 75Ω jack on the rear of the TV. 3 Insert the TV’s power plug into the wall socket. SOURCE SELECT > ? +A -A VOLUME CHANNEL MENU NOTE: The orientation of the TV buttons may be vertical or horizontal, based on model.The button functions, however, are the same in all models. Models 50PP9202 and 60PP9202 USING THE TV BUTTONS S hould your remote control be lost or broken, you can still change some of the basic picture and sound settings with the buttons on the TV. Follow the steps below to familiarize yourself with the functions of the TV buttons. 1 Press POWER/STANDBY to turn the TV on (or off). Allow about 10 seconds for the TV to power on. 2 Press the VOL(ume) + or – buttons to decrease or increase the sound level. Press the VOL(ume) + and – buttons simultaneously to dis- play the onscreen menu. After the menu appears, use these buttons to enter submenus and make selections or adjust- ments. (Use the CH[annel] Up and Down buttons to move up and down in the menu or submenus.) Press both VOL(ume) buttons simultaneously to back out of the onscreen menus. 3 Press SOURCE SELECT to choose from among the sig- nal inputs you have connected to the TV. 4 Press the CH(annel) Up and Down buttons to select TV channels. INSTALLING BATTERIES T o load the supplied batteries into the remote, follow these steps. 1 Gently press and hold the indention on the back of the remote and slide the battery cover off the remote. 2 Place the two “AA” size batteries in the remote’s bat- tery case. Ensure that the (+) and (–) ends of the batteries line up correctly with the (+) and (–) inside the case. 3 Slide the battery cover back into place. POINTING THE REMOTE Press the TV mode button on the remote to ensure that the remote sends its commands to the TV. When operating the remote control, point the remote toward the remote sensor window on the TV. To prevent battery leakage that may result in injury to you or damage to the remote control: • Install ALL batteries correctly, + and –, as marked on the unit. • Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.) • Remove batteries when the remote control is not used for a long time. Do not take apart, heat, or put batteries in fire. Model 43PP9202 Remote Sensor Window Power Standby Button CABLE CONVERTER BOXES You can set up your TV remote control to work with accessory devices such as VCRs, DVD players, and cable converter boxes. See pages 16–21 in the Directions for Use manual. c CHECK IT OUT 2 BATTERY USAGE CAUTION • Be sure to point the remote toward the sensor window on the TV or accessory device you are using the remote to operate. • Press the correct mode button for the device you want to operate: TV, VCR, ACC (for accessories other than VCRs). • Be within about 30 feet (10 meters) of the TV or accessory device you are using the remote to operate. • Avoid dropping the remote on hard sur- faces. • Do not use harsh chemicals to clean the remote. Use only a soft, lightly mois- tened cloth. HELPFUL HINTS

HEADPHONE STEREO MONO STEREO STEREO PICTURE SOUND FEATURES INSTALL TREBLE BASS BALANCE AVL INCR . SURROUND TREBLE 30 BASS BALANCE AVL INCR . SURROUND SOUND OR 2 3 INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron AV3 AV4 1 2 3 AV3 AV4 1 2 3 TIMER AutoLock PIP CLOSED CAP FORMAT TIME START TIME STOP TIME CHANNEL ACTIVATE FEATURES TIMER FEATURES TIME 8:06 PM START TIME STOP TIME CHANNEL ACTIVATE MENU Make adjustments or selections within a submenu. Also from a Submenu, enter a list to make selections. Go from one submenu to another and make settings or adjustments. TIMER SUBMENU FEATURES SUBMENU SOUND SUBMENU INSTALL SUBMENU ADJUSTING OR SETTING MENU OPTIONS A menu is simply a list of options. You can adjust or set your TV’s onscreen menu options by pressing buttons on the remote control. The following steps will familiarize you with how to use the remote control with the onscreen menu. 1 Press the TV mode button to ensure that the remote con- trol is in TV mode. 2 Press the MENU/SELECT button to bring the menu to the screen. Then, as necessary, press the CURSOR RING DOWN or UP to highlight a menu option. Press the CUR- SOR RING RIGHT to enter the submenu for the option. 3 Within the submenu, press the CURSOR RING DOWN or UP to highlight an option. Based on the submenu you are in, you can press the CUR- SOR RING RIGHT or LEFT to make an adjustment, select a setting, or enter a list or another submenu. You can return to the submenu from a list by pressing the CURSOR RING LEFT. To go from a submenu to the previous menu, highlight the option at the top of the screen and press the CURSOR RING UP. You can also press MENU/SELECT to return to the previous menu. Press STATUS/EXIT to exit the menu. PIP ON/OFF 2 1 3 5 4 6 8 7 9 0 TV SWAP PIP CH DN UP ACTIVE CONTROL FREEZE SOUND MUTE SURF A/CH POWER PICTURE STATUS/ EXIT SURF ITR/ RECORD HOME VIDEO HOME MOVIES PERSONAL SLEEP REC • PIP POSITION VCR ACC MENU/ SELECT VOL CH TV/VCR FORMAT SAP PROG.LIST DOLBY V AV Power Press to turn the TV on or off. Active Control™ Measures and corrects all incoming signals in order to provide the best picture quality settings. See page 53 in the Directions for Use manual. Press to select the Active Control™values On or Off. On: Sharpness and Noise reduction are controlled automatically. The picture settings are being adapted continuously and auto- matically. Picture Press to select an AutoPicture™control. Choose from four factory-set controls—Movies, Sports, Weak Signal, and Multimedia—and a PERSONAL control that you set according to your own preferences through the onscreen Picture menu. See page 24 in the Directions for Use manual. The four factory-set controls will enhance the TV picture according to the particular type of program you are watching. It may also be used to enhance pictures with weak signals. Menu/Select Press to display the onscreen menu. Press to return to a higher menu level. Channel +/– Press to select channels in ascending or descending order or cycle through the signal inputs. Mute Press to turn the TV sound off. To restore the sound to its previous level, press the button again. See pages 15 and 51 in the Directions for Use manual. Surf Press to select previously entered channels. With the TV’s AutoSurf™control, you can place up to 10 favorite channels or sources in memory. Then by pressing the Surf button, you can quickly view the selected channels. (See page 25 in the Directions for Use manual that came with the TV to learn how to select a series of your favorite channels using the Surf button.) Format Press to cycle through the picture Format options. For TV, AV1, CVI, AV2, and AV3 (side-panel jacks), the options are 4:3, AUTO, and EXPAND 4:3. For AV4 the options are 4:3 and COMPRESS 16:9. (See page 52 in the Directions for Use manual.) Sleep Press to set the TV to automatically turn itself off after a period of time. Choose 15, 30, 45, 60, 90, 120, 180, or 240 minutes before the TV will automatically turn off. (See page 27 in the Directions for Use manual.) Program List Press to display a list of channel numbers and their names. See the “Tuner Mode,” “Auto Program,” “Channel Edit,” and “Name” sec- tions on pages 4–6 in this guide for setup. Each channel will appear as a selectable menu item. The current channel will be highlighted as default. Five channels will be listed on screen at one time. Press the Cursor Ring up or down to scroll the list and and highlight a channel. Press the Cursor Ring right to tune to the highlighted channel. Channels marked “Skipped” in the Channel Edit control will not appear in the list. Each channel that is being blocked by AutoLock™ will appear with a padlock icon to indicate that the channel is not viewable. (See page 26 in the Directions for Use manual.) Dolby V Press to select various factory surround sound listening modes. Dolby* Virtual (Virtual Dolby Surround) (with Virtual Dolby Surround signals) Dolby Virtual uses two speakers to simulate the surround effect produced by a multichannel system. Incredible Surround™ • In Stereo sound mode—when Incredible Surround™is turned on—it seems as though the loudspeakers are spread farther apart from each another. • In Mono sound mode—when Incredible Surround™is turned on—enables you to hear a spatial sound effect. (See page 33 in the Directions for Use manual.) VCR control buttons Press to pause, rewind, stop, play, or fast forward a videotape. TV • VCR • ACC (Mode buttons) Press to send remote signals to either the TV, VCRs, or other accessory devices such as cable TV converters, satellite receivers, DVDs, or laser disc players. (See pages 16–21 in the Directions for Use manual that came with your set for details about setting your TV remote to work accessory devices. The capability of your TV remote to work the different functions of accessory devices may vary based on the accessory device.) PIP buttons: SWAP, PIP CH DN/UP, FREEZE Press to operate the Picture-in-Picture (PIP) features. See page 7 in this publication for more information on using these buttons. Sound Press to select an AutoSound™control. (See page 23 in the Directions for Use manual.) Choose from three factory-set controls— Voice, Music, and Theatre—and a Personal control that you set according to your own preferences through the onscreen Sound menu. The three factory-set controls will tailor the TV sound so as to enhance the type of program you are watching. Status/Exit Pressing the button once shows the current channel number, name (if set), time (if set), Sleep Timer setting, and sound setting (stereo, mono, SAP, or mute). Pressing the button twice shows the current AutoLock™settings. Pressing the button once when an onscreen dis- play is showing removes the onscreen display. Cursor Ring Up/Down: allows you to select the next or previous menu item in the menu. Left/Right: allows you to access the submenus, to adjust the settings, and to select another picture format. Volume +/– Press to adjust the TV sound level. Number Buttons Press to select TV channels. When selecting single-digit channels, press the number of the desired channel. The TV will pause for a few seconds and then tune to the selected channel. TV/VCR Press while in VCR mode to view the playback of a videotape. Press again to return to TV mode. A/CH Press to alternate between the currently viewed channel and the previ- ously viewed channel. Rec ¶ Press this button simultaneously with the 3 button when in VCR mode to record. SAP Press to select between main sound and SAP (Second Audio Program) when you tune to a program offering SAP. (See page 35 in the Directions for Use manual.) AV Press repeatedly to select the different signal sources connected to the TV: TV, AV1, CVI, AV2, AV3 (side jack panel), and AV4. (See page 22 in the Directions for Use manual.) Clock Press to access the onscreen Timer menu, where you can set the time for the TV’s clock or set the TV’s Timer features, such as channel switch over, power on set, and power off set. (See page 5 of this publi- cation for setting the time manually. See pages 37–41 in the Directions for Use manual for information on using the TV’s Timer feature.) Position Press to move the PIP picture to any of the four corners of the screen. Back Light button Press to light the buttons on the remote control. PIP Press to turn PIP (picture-in-picture) on or off or control the size of the PIP window. See pages 6 and 7 of this publication for more infor- mation on PIP. • If you don’t press any remote buttons, the menu will automatically disap- pear after about 20 seconds. To bring the menu back, press MENU/SELECT. • Sometimes not all the menu items are visible on the screen. If more items exist in the menu, a cursor arrow will appear. Also, a bullet will appear for each remain- ing item, up to a maximum of three. This will help you determine how many items are left in the menu. Keep pressing the CURSOR RING DOWN until you dis- play all items. • Should your remote become lost or otherwise unavailable for use, you can use the but- tons on the front of the TV to access the onscreen menu and make adjustments or set- tings. See page 2. HELPFUL HINTS REMOTE CONTROL OPERATING THE TELEVISION AND REMOTE CONTROL (CONTINUED) Active Control, AutoPicture, AutoSound, AutoSurf, and Incredible Surround are trademarks of Philips Consumer Electronics North America. Copyright 2002 Philips Consumer Electronics. *Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trade- marks of Dolby Laboratories. TV SWAP PIP CH DN UP FREEZE SOUND POWER PICTURE VCR ACC ACTIVE CONTROL

LANGUAGE PICTURE SOUND FEATURES INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron S et the TUNER MODE control according to the type of signal you have connected to the TV—ANTENNA or CABLE. If you select AUTO, the TV will automatically detect the type of signal you have connected. 1 Press the MENU/SELECT button. The onscreen menu appears. Press the CURSOR RING DOWN repeatedly until INSTALL is highlighted. 2 Press the CURSOR RING RIGHT to enter the INSTALL submenu. Then press the CURSOR RING DOWN once to highlight TUNER MODE. 3 Press the CURSOR RING RIGHT to highlight the TUNER MODE options list. 4 Press the CURSOR RING DOWN or UP repeatedly until you select the option that matches your signal connection, CABLE or ANTENNA. If you want the TV to determine the type of signal, select AUTO. (You have selected an option when the dot and triangle are next to the option.) 5 Press the STATUS/EXIT button to exit the menu. 6 Proceed to the section on “Auto Program.” T he menu LANGUAGE control enables you to set the TV’s onscreen menu and onscreen displays to be shown in English, French, or Spanish. Follow the steps in this section to set the control. 1 Press the MENU/SELECT button. The onscreen menu appears. 2 Press the CURSOR RING DOWN repeatedly until INSTALL is highlighted. Then press the CURSOR RING RIGHT to enter the INSTALL submenu. 3 Press the CURSOR RING RIGHT again to highlight the menu LANGUAGE options list. 4 Press the CURSOR RING DOWN or UP to select your menu language. Instantaneously, the onscreen displays appear in the lan- guage that you choose. 5 Press the STATUS/EXIT button to exit the menus. AUTO PROGRAM TV SWAP PIP CH DN UP FREEZE SOUND MUTE POWER PICTURE STATUS/ EXIT VCR ACC MENU/ SELECT VOL CH ACTIVE CONTROL INSTALL SEARCH LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron CABLE PLEASE WAIT CHANNEL 12 1 4 2,3 HELPFUL HINTS After you’ve run AUTO PROGRAM, check the results. Press the CH(annel) +/– buttons on your remote to cycle through your available channels. Or press the PROG. LIST button to show a list of the chan- nels and tune to them. See page 26 in the Directions for Use man- ual for more on Program List. T he AUTO PROGRAM feature will scan for channels with active broadcast signals and store those channels in the TV’s memory. It will tune up to 69 channels for antenna, and up to 125 channels for cable. After you run AUTO PROGRAM, you can use the CH(annel) +/– buttons to quickly and easily select stations. You can also press the PROG. LIST (Program List) button on your remote to see a list of the channels. 1 Press the MENU/SELECT button. The onscreen menu appears. Then press the CURSOR RING DOWN repeated- ly until INSTALL is highlighted. 2 Press the CURSOR RING RIGHT to enter the INSTALL submenu. Then press the CURSOR RING DOWN repeatedly until AUTO PROGRAM is highlighted. 3 Press the CURSOR RING RIGHT to begin the automatic search for channels. The progress of autoprogramming is dis- played. 4 When the programming is done, press the STATUS EXIT button to exit the menu. c CHECK IT OUT 2 1 3 5 4 6 TV SWAP PIP CH DN UP FREEZE SOUND MUTE POWER PICTURE STATUS/ EXIT VCR ACC MENU/ SELECT VOL CH ACTIVE CONTROL PICTURE SOUND FEATURES INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron ENGLISH FRANCAIS ESPANOL ˜ 3 1 2,4 5 ENGLISH FRANCAIS ESPAÑOL OR French INSTALLATION LANGUE TUNER MODE PROGRAM.AUTO CHANGER CANAL AutoChron FRANCAIS ESPAÑOL ENGLISH Spanish INSTALAR IDIOMA SINTONIZADOR AUTO PROG. EDITAR CANAL AutoChron ESPAÑOL ENGLISH FRANCAIS OR Make your selection and instantaneously the onscreen display appears in the language you chose. HELPFUL HINT The LANGUAGE con- trol makes only the TV’s onscreen menu items appear in English, French, or Spanish text. The control does not change the language of Closed Captioning (CC) text that may be included with programs. PICTURE SOUND FEATURES INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron PICTURE SOUND FEATURES INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron • Philips strongly recom- mends that you run Auto Program. Otherwise, the TV may not tune the channels properly, result- ing in improper pictures. • If you change signal sources—to a new cable company or from anten- na to cable, for exam- ple—be sure that Tuner Mode is properly set for the new source. Then run Auto Program again. This will ensure that the channels are correctly stored in the TV’s mem- ory. • If you have made AutoLock™settings, remember that you must remove any channel blocks before Auto Program will work. (See pages 42–50 in the Directions for Use man- ual.) HELPFUL HINT If you select the Tuner Mode option that matches your signal source rather than AUTO, the time required for AUTO PROGRAM to store channels to the TV’s memory can be reduced.

AutoChron SETTING TIME AUTOMATICALLY The steps in this section tell you how to set AutoChron™to down- load the time from your PBS station to your TV. After successful setup, AutoChron™will automatically maintain the correct time using your PBS station until you set the time manually. 1 Press the MENU/SELECT button. The onscreen menu appears. Then press the CURSOR RING DOWN repeatedly until INSTALL is highlighted. 2 Press the CURSOR RING RIGHT to enter the INSTALL submenu. Then press the CURSOR RING DOWN repeated- ly until AutoChron is highlighted. 3 Press the CURSOR RING RIGHT to enter the AutoChron SET TIME area. 4 Press the CURSOR RING RIGHT again to select AUTO. Within a few seconds, a menu containing the time-zone options appears. 5 If necessary, press the CURSOR RING UP or DOWN to highlight your correct time zone. Then press the CURSOR RING RIGHT. Within a few seconds, the option of Daylight Savings Time appears on screen. 6 If the Daylight Savings Time option you want to select is not highlighted, press the CURSOR RING UP or DOWN to highlight the option. Then press the CURSOR RING RIGHT to activate your selection. 7 Press the number buttons on your remote to enter the chan- nel number for your PBS station (02, 15, or 121, for exam- ple). Wait until the TV completes its search. If the time was not found, you will need to locate the correct channel number for your PBS station and input that number. 8 Press the STATUS/EXIT button to exit the menu. CHANNEL EDIT T his feature allows you to edit or skip channels from the channel list that have bad or weak signals or channels you do not want to watch. 1 Press the MENU/SELECT button. The onscreen menu appears. Then press the CURSOR RING DOWN repeatedly until INSTALL is highlighted. Press the CURSOR RING right to enter the INSTALL submenu. 2 Press the CURSOR RING DOWN repeatedly until CHAN- NEL EDIT is highlighted. Then press the CURSOR RING RIGHT or LEFT to access the CHANNEL EDIT list. 3 Press the CURSOR RING UP or DOWN to scroll through the list of channels. Or press the NUMBER buttons on your remote control to select a specific channel. 4 With the channel you want to edit selected, press the CURSOR RING RIGHT to mark the channel as SKIPPED. (Channels you mark SKIPPED will not appear when you use the CH[annel] +/– buttons to change channels while watching TV.) When you want to add a channel that has been marked SKIPPED, press the CURSOR RING UP or DOWN to high- light the channel. Then press the CURSOR RING RIGHT to remove the word SKIPPED. 5 Press the STATUS/EXIT button to exit the menu. 2 1 3 5 4 6 TV SWAP PIP CH DN UP FREEZE SOUND MUTE POWER PICTURE STATUS/ EXIT VCR ACC MENU/ SELECT VOL CH ACTIVE CONTROL INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron AV3 AV4 1 2 SKIPPED 3 1 4 3 2 5 AV3 AV4 1 2 3 HELPFUL HINT Channels that Auto Program (see page 4) determined not to con- tain active broadcast sig- nals are marked SKIPPED. PIP 2 1 3 5 4 6 8 7 9 0 TV SWAP PIP CH DN UP FREEZE SOUND MUTE SURF A/CH POWER PICTURE STATUS/ EXIT POSITION VCR ACC MENU/ SELECT VOL CH TV/VCR ACTIVE CONTROL SET TIME AUTO MANUAL INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL SET TIME CENTRAL MOUNTAIN PACIFIC LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL DAYLIGHT SAVING TIME? YES NO LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL SEARCH FOR TIME ENTER CHANNEL 02 PBS LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL SEARCH FOR TIME PLEASE WAIT 15 PBS SEARCH FOR TIME TIME FOUND END: PRESS STATUS 11:15 AM LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL SEARCH FOR TIME TIME NOT FOUND RE-ENTER CHANNEL 15 PBS LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL OR 1 2,3, 4 7 8 5, 6 AUTO MANUAL TIME ZONE? The message shown to the right indicates that AutoChron™ is not finding a PBS station at the chan- nel you input. Check the channel number for your PBS station.You will need to input the correct num- ber for the time to be found. 2 1 3 TV SWAP PIP CH DN UP FREEZE SOUND MUTE POWER PICTURE STATUS/ EXIT VCR ACC MENU/ SELECT VOL CH ACTIVE CONTROL SET TIME AUTO MANUAL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL 11:00 AM LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron INSTALL 1 3 4 2 ENTER TIME HELPFUL HINTS • The CLOCK button \ on your remote provides another way in which you can set the TV’s clock manu- ally. • After setting the clock, you will be able to access the time by pressing the STATUS/EXIT but- ton. Or you can view the time constantly in the upper right-hand corner of the screen by turning the DIS- PLAY control on (see page 38 in the Directions for Use manual). SETTING TIME MANUALLY 1 Follow steps 1–3 above, then press the CURSOR RING DOWN to highlight MANUAL and CURSOR RING RIGHT to enter the MANUAL time input area. 2 Use the number buttons on your remote control to input the first digit for the time. You can also press the CURSOR RING UP or DOWN to select a digit. Press the CURSOR RING RIGHT to move to the next digit input slot and input the time. If you should need to change a number you have input, you can cursor left or right to the digit input slot to make the correction. 3 After you have input the time, press the CURSOR RING RIGHT to enter the AM/PM area. Then press the CURSOR RING UP or DOWN to select AM or PM. 4 Press the STATUS/EXIT button to exit the menu. PICTURE SOUND FEATURES INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron PICTURE SOUND FEATURES INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron PIP ON/OFF 8 7 9 0 SURF A/CH SURF ITR/ RECORD HOME VIDEO HOME MOVIES PERSONAL SLEEP REC • PIP POSITION TV/VCR FORMAT SAP PROG.LIST DOLBY V AV CLOCK Button A utoChron™gives you the option of setting the time manually or automatically.

NAME T he channel NAME feature allows you to list the “call” letters of your favorite stations beside their channel numbers when they appear on the screen. The TV has in memory a list of the 50 most popular channel names (NBC, ABC, or FOX, for example). You also can enter a custom name (up to five characters). 1 Press the NUMBER buttons, the CH(annel) +/– buttons, or the AV button to select a TV channel or input source to which you want to assign a name or whose name you want to modify. 2 Press the MENU/SELECT button. The onscreen menu appears. Then press the CURSOR RING DOWN repeated- ly until INSTALL is highlighted. Press the CURSOR RING RIGHT to enter the INSTALL submenu. 3 Press the CURSOR RING DOWN repeatedly until the NAME control is highlighted. Then press the CURSOR RING RIGHT to highlight the NAME options area. 4 At this point you can choose between options of creating a personal name for the channel or selecting a preset one from a list. To create your own personal name for the channel or change a personal name you created previously, press the CURSOR RING RIGHT. Then press the CURSOR RING UP or DOWN to select the first character of the name. You can input up to five characters for the name. When finished, press the MENU/SELECT button. Or To choose from the list of preset names, press the CUR- SOR RING UP or DOWN to highlight your choice for the channel name. Press the CURSOR RING RIGHT to select the name. Then press the MENU/SELECT button. 5 Press the STATUS/EXIT button to exit the menu. When you press the STATUS/EXIT button when no onscreen display is present or change to the channel you’ve named, the name will appear on screen next to the channel number or signal source name. PIP ON/OFF 2 1 3 5 4 6 8 7 9 0 TV SWAP PIP CH DN UP ACTIVE CONTROL FREEZE SOUND MUTE SURF A/CH POWER PICTURE STATUS/ EXIT SURF ITR/ RECORD HOME VIDEO HOME MOVIES PERSONAL SLEEP REC • PIP POSITION VCR ACC MENU/ SELECT VOL CH TV/VCR FORMAT SAP PROG.LIST DOLBY V AV INSTALL TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron NAME PERSONAL INSTALL TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron NAME PERSONAL WX- WXY- WXYZ- WXYZ3 4 2 1 3 5 4 1 1 Create your own personal name for a channel. OR Choose from a list of preset options. INSTALL USA VH WGN WOR WTHR TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron NAME HELPFUL HINTS • The five PERSONAL name characters you can input may be let- ters, a dash, or the numbers 0 through 9. • If you begin inputting a personal name or changing an existing one and decide you’d rather select a name from the preset list, press the MENU/SELECT but- ton. This will return you to the INSTALL submenu, with NAME highlighted. Simply press the CURSOR RING RIGHT to high- light the NAME options area again and choose a preset name as explained in step 4 to the left. USING THE PICTURE-IN-PICTURE (PIP) FEATURE VIDEO S-VIDEO L Pb Pr VIDEO S-VIDEO L AUDIO L R AUDIO L R G/Y R/Pr B/Pb V H SYNC L R AUDIO HD INPUT-AV 4 INPUT-AV 2 OUTPUT INPUT-AV 1 ANTENNA IN 75Ω Y 1 Two-way Signal Splitter Rear of VCR Coaxial Cable Lead-in from VHF/UHF Antenna or Cable TV Company ANTENNA OUT ANTENNA IN VIDEO AUDIO IN IN OUT OUT R L Rear of TV 2 2 3 4 MAKING PIP CONNECTIONS P icture-In-Picture (PIP) is the showing of two pictures on the TV screen at the same time—one main screen picture and one small picture, or PIP. The picture for the PIP window can come from an antenna or cable TV signal, or from AV1, AV2, or AV3. NOTE: CVI cannot be displayed in the PIP window, and AV 4 does not function with PIP. The following connections explained below will allow you to use a VCR as a second tuner specifically for PIP. In other words, you can use the VCR to select channels for viewing in the PIP window. This is just one example of how you can use PIP. Note, too, that you can swap the main and PIP pictures on screen. See page 7 in this publication for information on viewing PIP pic- tures and using the PIP buttons. To make the connections shown in this example, you will need: • a two-way signal splitter • two coaxial cables (75Ω) • one cable for a video connection (standard RCA connector) • two cables for audio connections (standard RCA connectors). NOTE: The two-way signal splitter and cables are not supplied with your TV. You should be able to buy them at most stores that sell elec- tronics. Or you can call our Customer Care Center at 1-800-531-0039. 1 Connect an antenna or cable TV signal to a two-way signal splitter. 2 Use coaxial cables to connect from the two-way signal splitter to the ANTENNA IN 75Ωjack on the rear of the TV and to the ANTENNA IN jack on the rear of the VCR. 3 Connect the VIDEO OUT jack on the VCR to the INPUT-AV1 VIDEO jack on the rear of the TV. 4 Connect the AUDIO OUT jacks, L(eft)/R(ight), on the rear of the VCR to the INPUT-AV 1 AUDIO jacks, L(eft)/R(ight,) on the rear of the TV. PIP Window Main Screen PICTURE SOUND FEATURES INSTALL LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT AutoChron You can use a variety of connections to provide input sources for view- ing in PIP. For more information, see the sec- tion on “Connecting Accessory Devices to Your TV,” beginning on page 6 in the Directions for Use manual. c CHECK IT OUT HELPFUL HINT If your VCR is mono (nonstereo), you will connect only one audio cable. You must be sure that the TV is set to MONO for the AV input source to which you’ve connected the VCR (INPUT-AV 1, INPUT-AV 2, or the side panel inputs [AV3]). Otherwise, you will receive sound from only one of the TV’s speakers. See page 34 in the Directions for Use manual that came with the TV.

T he Picture-in-Picture (PIP) COLOR and TINT controls allow you to make fine-tune adjustments to the PIP picture settings. 1 Press the MENU/SELECT button. The onscreen menu appears. Then press the CURSOR RING DOWN twice to highlight FEATURES. 2 Press the CURSOR RING RIGHT to enter the FEA- TURES submenu. Then press the CURSOR RING DOWN repeatedly until the PIP item is highlighted in the submenu. Press the CURSOR RING RIGHT to enter the PIP sub- menu. 3 Press the CURSOR RING RIGHT or LEFT to adjust the COLOR to the desired level. Then press the CURSOR RING DOWN to highlight the TINT adjustment bar. Press the CUR- SOR RING RIGHT or LEFT to adjust the TINT bar to the desired level. 4 Press the STATUS/EXIT button to exit the menu. TV SWAP PIP CH DN UP FREEZE SOUND MUTE POWER PICTURE STATUS/ EXIT VCR ACC MENU/ SELECT VOL CH ACTIVE CONTROL FEATURES TIMER AutoLock PIP CLOSED CAP FORMAT COLOR TINT FEATURES COLOR 44 TINT PIP FEATURES COLOR TINT 50 PIP 1 4 2,3 PIP 2 1 3 5 4 6 8 7 9 0 TV SWAP PIP CH DN UP FREEZE SOUND MUTE SURF A/CH POWER PICTURE STATUS/ EXIT POSITION VCR ACC MENU/ SELECT VOL CH TV/VCR ACTIVE CONTROL 3 5 5 2 STOP/EJECT RECORD MENU STATUS/EXIT F.FWD PAUSE REW CHANNEL VCR/TV PLAY VIDEO L AUDIO R POWER VIDEO CASSETTE RECORDER CH 1 4 USING THE PICTURE-IN-PICTURE (PIP) FEATURE (CONTINUED) T he steps below take you through the process of using a VCR as a tuner to select channels for viewing in PIP. 1 Turn the VCR and TV on. Then press the VCR/TV button on the VCR to place the VCR in TV mode. 2 If the PIP window isn’t already on the screen, press the PIP on/off button on the TV remote. The PIP window will show in one of the four corners of the TV screen. 3 Press the PIP CH DN/UP button until the input source to which you connected the VCR appears in the PIP window. The onscreen display appears briefly to identify the signal source. 4 Select the channel on the VCR to view in the PIP window. You can select channels on your VCR with your TV remote if the remote is programmed to work with the VCR. You must press the VCR mode button first to send commands to the VCR. (See pages 16–21 in the Directions for Use manu- al.) 5 Press the TV button on your TV remote and select the channel on your TV that you want to watch on the main screen. 6 Go to the next section to familiarize yourself with the func- tions of the PIP buttons. HELPFUL HINT If you use your TV remote to operate the VCR, be sure the TV remote is in the correct mode when you switch back and forth between VCR and TV. USING THE PIP BUTTONS PIP 2 1 3 5 4 6 8 7 9 0 TV SWAP PIP CH DN UP FREEZE SOUND MUTE SURF A/CH POWER PICTURE STATUS/ EXIT POSITION VCR ACC MENU/ SELECT VOL CH TV/VCR ACTIVE CONTROL 2 4 1,6 5 3 POSITION SWAP FREEZE Ski Vacations P.O. Box 55512 Anytown, USA 87654 1-800-555-1212 U sing the PIP buttons on the remote, you can move the PIP window around and swap it with the main screen. You can also freeze the PIP window picture. 1 Press the PIP on/off button to show the PIP window. PIP appears in a corner of the TV screen. Press the PIP on/off again to reduce the PIP window size, and a third time to remove the PIP window from the screen. Press the PIP on/off button again to show the PIP window. 2 Press the PIP CH DN/UP buttons to access a signal source in the PIP window. 3 Press the PIP POSITION button to move the PIP win- dow from corner to corner on the TV screen. This feature allows you to move PIP and avoid blocking any main-screen action. 4 With PIP on the TV screen, press the SWAP button to swap the main and PIP pictures. Press SWAP again to swap the pictures back. 5 Press the FREEZE button to stop motion within the PIP window. Stopping motion will allow you to write down onscreen phone numbers or addresses. 6 Press the PIP on/off button, multiple times if necessary, to remove the PIP window from the screen. HELPFUL HINT When you press the PIP on/off button to show the PIP window, the window will appear where it was located the last time it was dis- played. Be careful not to leave the PIP window on the screen continuously for an extended period time. Doing so day after day for a couple of hours or more may cause picture- tube damage. WARNING

CONVERGE RED/BLUE C onvergence is the correct lining up of the red and blue light paths on the TV screen. If the paths don’t line up, color fringes will appear around objects on screen. If no color fringes show, then no convergence adjustments are necessary. NOTE: Allow the TV to warm up 20 minutes before adjusting convergence. See the chart to the right for guidance as to which convergence controls to use. 1 Press the MENU/SELECT button. The menu appears. Press the CURSOR RING RIGHT to enter the PICTURE submenu. Then press the CURSOR RING DOWN until MANUAL CONVERGE is highlighted. 2 Press the CURSOR RING RIGHT to enter the MANUAL CONVERGE submenu. If you want to adjust the Red Convergence, press the CURSOR RING RIGHT to enter the adjust mode. If you want to adjust the Blue Convergence, press the CURSOR RING DOWN to highlight CONVERGE BLUE, then press the CURSOR RING RIGHT to enter adjust mode. 3 In adjust mode, press the CURSOR RING RIGHT, LEFT, UP, or DOWN to adjust the cross hair until the color outline around it is gone. (The adjustment is automatically saved in the TV’s memory.) To return to the MANUAL CONVERGE menu, press the MENU/SELECT button. To exit the onscreen display, press the STATUS/EXIT button. 2 1 3 5 4 6 TV SWAP PIP CH DN UP FREEZE SOUND MUTE POWER PICTURE STATUS/ EXIT VCR ACC MENU/ SELECT VOL CH ACTIVE CONTROL CONVERGE RED CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT PICTURE MANUAL CONVERGE Converge Red Converge Red 2,3 1 MULTIPOINT RED/BLUE T he Multipoint Red/Blue Convergence controls enable you to adjust the convergence at specific points on the TV screen. NOTE: The onscreen display will leave the screen after 20 seconds of inactivity. If this happens, simply press the MENU/SELECT button to bring the MANUAL CONVERGE submenu back. 1 Press the MENU/SELECT button. The menu appears. Press the CURSOR RING RIGHT to enter the PICTURE menu. Then press the CURSOR RING DOWN until MANUAL CONVERGE is highlighted. 2 Press the CURSOR RING RIGHT to enter the MANUAL CONVERGE submenu. Press the CURSOR RING DOWN until MULTIPOINT RED or MULTIPOINT BLUE is highlighted. Then press the CURSOR RING LEFT or RIGHT to enter Navigate mode. 3 Press the CURSOR RING LEFT, RIGHT, UP, or DOWN to move to a cross hair that has a color outline. Then press the STATUS/EXIT button to enter adjust mode. 4 Press the CURSOR RING LEFT, RIGHT, UP, or DOWN to adjust the cross hair image until the color out- line is gone.Then press the STATUS/EXIT button to return to NAVIGATE mode. Repeat steps 3 and 4 until all mis- aligned cross images have been adjusted. 5 After making your adjustments, you must store them in the TV’s memory using SAVE MULTIPOINT. NOTE: If you are not satisfied with the adjustments you just made and want to start over, you can use the UNDO MULTIPOINT control. This control allows you to undo the adjustments, but it will work only if you use it before saving. To save your multipoint adjustments, press the MENU/SELECT button. This returns you to the MANUAL CONVERGE menu. Press the CURSOR RING DOWN until SAVE MULTIPOINT is highlighted. Then press the CURSOR RING LEFT or RIGHT to store your adjustments in the TV’s memory. OR To undo the multipoint adjustments you just made, press the MENU/SELECT button. This returns you to the MANUAL CONVERGE menu. Press the CURSOR RING DOWN until UNDO MULTIPOINT is highlighted. Press the CURSOR RING LEFT or RIGHT to undo the adjustments. Press the CURSOR RING UP until MULTIPOINT RED or MULTIPOINT BLUE is highlight- ed. Press the CURSOR RING LEFT or RIGHT to enter Navigate mode. Then Follow steps 3–5 above to make your adjustments again. OR To restore the TV’s convergence to factory settings, press the MENU/SELECT button. This returns you to the MANUAL CONVERGE menu. Press the CURSOR RING DOWN until RESTORE FACTORY is highlighted. Then press the CURSOR RING LEFT or RIGHT to restore the TV’s convergence to factory settings. 6 Press the STATUS/EXIT button to exit the submenu. CONVERGE RED CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT PICTURE MANUAL CONVERGE É L L CONVERGE RED CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT PICTURE MANUAL CONVERGE to Navigate Exit to Adjust PIP 2 1 3 5 4 6 8 7 9 0 TV SWAP PIP CH DN UP FREEZE SOUND MUTE SURF A/CH POWER PICTURE STATUS/ EXIT POSITION VCR ACC MENU/ SELECT VOL CH TV/VCR ACTIVE CONTROL 1,5 3,4 to Navigate Exit to Adjust to Adjust Exit to Navigate to Navigate Exit to Adjust to Adjust Exit to Navigate to Adjust Exit to Navigate É L L CONVERGE RED CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT PICTURE MANUAL CONVERGE L CONVERGE RED CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT PICTURE MANUAL CONVERGE SAVE MULTIPOINT L CONVERGE RED CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT STORED PICTURE MANUAL CONVERGE OR L CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT UNDO MULTIPOINT PICTURE MANUAL CONVERGE UNDO MULTIPOINT L CONVERGE BLUE MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT UNDO MULTIPOINT RESTORED PICTURE MANUAL CONVERGE OR RESTORE FACTORY L MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT UNDO MULTIPOINT RESTORE FACTORY RESTORED PICTURE MANUAL CONVERGE L MULTIPOINT RED MULTIPOINT BLUE SAVE MULTIPOINT UNDO MULTIPOINT RESTORE FACTORY PICTURE MANUAL CONVERGE 6 2 n e e r c S e c n a r a e p p a n o it c A s u oir a V s e g a m i t u o h g u o r h t e rit n e e h t e v a h e r u tcip .s e nilt u o d e r e h t ts ujd A E G R E V N O C .lo rt n o c D E R d e r y n a fi n e h T ,nia m e r s e nilt u o e h t ts ujd a T N I O PI T L U M .lo rt n o c D E R s u oir a V s e g a m i t u o h g u o r h t e rit n e e h t e v a h e r u tcip .s e nilt u o e ulb e h t ts ujd A E G R E V N O C .lo rt n o c E U L B e ulb y n a fi n e h T ,nia m e r s e nilt u o e h t ts ujd a T N I O PI T L U M .lo rt n o c E U L B HELPFUL HINT If you should experi- ence a power outage before saving your mul- tipoint-convergence set- tings, your settings will be lost.