HP 2210 Setup Poster

desktop to appear. Close any open programs, including virus- checking programs. 2 Attach the cover Insert the two bottom tabs of the cover into the slots on the unit. Tilt the cover down and press firmly. Make sure the tabs lock into place and the cover is even with the unit. 4 Remove output tray and load paper Use blank white paper to prepare for print alignment. Connect the phone cord to wall jack 5 6 Connect the power cord and USB cable 7 Turn on your HP PSC 8 Insert and align the print cartridges 9 Finish software setup Remove the bright pink tape from the print cartridges. Do not touch the gold-colored contacts or retape the cartridges. Make sure both latches are locked into position. Close the door. Make sure the Device Setup complete screen appears. If you do not see this screen, check the reference guide for troubleshooting setup. The software may prompt you to restart. Lift the print carriage door up until it catches. Wait for the print carriage to move to the center. Lift the blue and gray latches. Pull the end of the gray latch toward you, press down until it stops, and then release. Make sure the latch catches below the bottom tabs. Repeat with blue latch. Press Enter to begin alignment. After a page prints, alignment is complete. Discard or recycle this page. a b Make sure you are using the correct side of the poster. Turn power On and wait for display prompt. Note: See the reference guide for adjusting the display viewing angle. Hold the black print cartridge with the label on top as shown. Slide the cartridge into the right (gray latch) side of the print carriage. Hold the color print cartridge with the label on top as shown. Slide the cartridge into the left (blue latch) side of the print carriage. f g a a b Make sure you have completed steps 1 and 2 before this step. a latches a Make sure to remove any packing material from inside the unit b c d d e e f g www.officejetsupport.com Copyright Hewlett-Packard Company 2002 Printed in USA 10 Set up faxing Make sure your PC is on. Follow the onscreen instructions to enter your name, phone number, and other important settings. See the reference guide for more details. Take the Product Tour to learn about your new HP PSC. a b c Windows setup poster hp psc 2200 series all-in-one a c d e f g 3 Windows users: Follow the steps in order. Do not connect the USB cable until instructed to do so. See your box for exact contents and system requirements. Insert the HP PSC software CD. Follow the onscreen instructions. When prompted to set up your device, go to step 3. c Install the software first a b Black label (56) Color label (57) To wall jack To phone/ modem/ office equipment Notes: If nothing appears on your computer screen after inserting the CD, go to the Windows task bar, click Start, and then choose Run. In the Run dialog box type d:\setup.exe (d= your PC's CD ROM drive letter). You may see the minimum requirements screen first. 1 2

Insert the two bottom tabs of the cover into the slots on the unit. Tilt the cover down and press firmly. Make sure the tabs lock into place and the cover is even with the unit. Remove output tray and load paper Use blank white paper to prepare for print alignment. Connect the USB cable 3 4 Connect the power cord and phone cord 5 Turn on your HP PSC 6 Insert and align the print cartridges Lift the print carriage door up until it catches. Wait for the print carriage to move to the center. Lift the blue and gray latches. Make sure both latches are locked into position. Close the door. 7 Install the software Turn your Macintosh on and wait for your Macintosh to finish starting up. Insert the HP PSC software CD. Double-click the HP All-In- One Installer icon on your desktop. 2 Remove the bright pink tape from the print cartridge. Do not touch the gold-colored contacts or retape the cartridges. Hold the black print cartridge with the label on top as shown. Slide the cartridge into the right (gray latch) side of the print carriage. Hold the color print cartridge with the label on top as shown. Slide the cartridge into the left (blue latch) side of the print carriage. Press Enter to begin alignment. After a page prints, alignment is complete. Discard or recycle this page. Try your new HP PSC 8 Whats next? Take the product tour Use the Director Check the reference guide for other ways to get started with your HP PSC. See your box for exact contents and system requirements. Windows users: see other side. Make sure you are using the correct side of the poster. a b latches Black label (56) Pull the end of the gray latch toward you, press down until it stops, and then release. Make sure the latch catches below the bottom tabs.Repeat with blue latch. Follow the onscreen instructions. You may have to restart your Macintosh during setup. Be sure to complete the setup assistant. If you have an iMac, your USB port is on the side. Do not connect the HP PSC to a USB port on a keyboard or non-powered USB hub. See reference guide for more details. Note: You can adjust the viewing angle of the display. See the reference guide for details. Make sure to remove any packing material from inside the unit. f a b a b a a b c d e b c d e f g g a b c a d Color label (57) Macintosh setup poster hp psc 2200 series all-in-one Be sure to insert the phone cord in the left slot on the back of your HP PSC as shown. To wall jack To phone/ modem/ office equipment