HP Compaq d530 USDT Getting Started Manual

D530 Ultra-Slim Desktop Model Document Part Number: 325444-001 April 2003 Use this guide after you have completed the steps detailed in the Quick Setup guide. It will help you set up factory-provided software. It also includes basic troubleshooting information should you have problems during the initial startup process.

© 2003 Hewlett-Packard Development Company, L.P. HP, Hewlett Packard, and the Hewlett-Packard logo are trademarks of Hewlett-Packard Company in the U.S. and other countries. Compaq is a trademark of Hewlett-Packard Development Company, L.P. in the U.S. and other countries. Microsoft and Windows are trademarks of Microsoft Corporation in the U.S. and other countries. Adobe, Acrobat, and Acrobat Reader are trademarks or registered trademarks of Adobe Systems Incorporated. All other product names mentioned herein may be trademarks of their respective companies. Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. The information in this document is provided “as is” without warranty of any kind, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, and is subject to change without notice. The warranties for HP products are set forth in the express limited warranty statements accompanying such products. Nothing herein should be construed as constituting an additional warranty. This document contains proprietary information that is protected by copyright. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. Å WARNING: Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. Ä CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. Getting Started Compaq Business Desktops D530 Ultra-Slim Desktop Model First Edition (April 2003) Document Part Number: 325444-001

Installing the Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Accessibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installing or Upgrading Device Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Customizing the Monitor Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Protecting the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Restoring the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Turning Off the Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Working with the MultiBay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 “Hot-Plugging” or “Hot-Swapping” MultiBay Drives. . . . . . . . . . . . . . . . . . . . . . . . . 5 Partitioning and Formatting a MultiBay Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Inserting a Drive into the MultiBay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Engaging and Releasing the MultiBay Security Catch. . . . . . . . . . . . . . . . . . . . . . . . . 8 Removing a Drive from the MultiBay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Finding More Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Locating Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Using the Documentation Library CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Before You Call for Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Basic Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Solving General Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Solving Hardware Installation Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Interpreting Diagnostic Lights and Audible Codes . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ordering the Quick Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Ä CAUTION: Do not add optional hardware or third-party devices to the computer until the operating system is successfully installed. Doing so may cause errors and prevent the operating system from installing properly. Installing the Operating System The first time you turn on the computer, the operating system is installed automatically. This process takes about 5 to 10 minutes, depending on which operating system is being installed. Carefully read and follow the instructions on the screen to complete the installation. Ä CAUTION: Once the automatic installation has begun, DO NOT TURN OFF THE COMPUTER UNTIL THE PROCESS IS COMPLETE. Turning off the computer during the installation process may damage the software that runs the computer or prevent its proper installation. If your computer was not shipped with a Microsoft operating system, some portions of this documentation do not apply. For complete operating system installation and configuration instructions, refer to the operating system documentation that was provided with the computer. Additional information is available in online help after you install the operating system. Accessibility HP is committed to designing products, services, and programs with improved usability and accessibility for all customers. HP products with Microsoft Windows XP preinstalled, or that are XP Ready, are

industry-leading Assistive Technology products to ensure equal access—anytime, anywhere . . . to anyone. Installing or Upgrading Device Drivers When installing optional hardware devices after the operating system installation is complete, you must also install the drivers for each of the devices. If prompted for the I386 directory, replace the path specification with C:\i386, or use the Browse button in the dialog box to locate the I386 folder. This action points the operating system to the appropriate drivers. You can obtain the latest support software, including support software for the operating system from: www.hp.com/support You can also obtain the latest support software through a subscription to the Compaq Support CD Kit using the Support Software Management order form available at the following Web site: http://www.compaq.com/support/files/desktops/us/ purchase.html This site also provides information on how to purchase a subscription. ✎ If the computer has an optical RW drive, you must install the appropriate application to be able to write to the drive. To install the application, double-click the Setup Software icon on the desktop or the application launcher and select the Easy CD Creator and Direct CD option when prompted. Customizing the Monitor Display You can manually select or change the monitor model, refresh rates, screen resolution, color settings, font sizes, and power management settings. To do so, right-click on the Windows Desktop, then click

the online documentation provided with the graphics controller utility or the documentation that came with your monitor. Protecting the Software To protect the software from loss or damage, you should keep a backup copy of all system software, applications, and related files stored on the hard drive. Refer to the operating system or backup utility documentation for instructions on making backup copies of your data files. Restoring the Software Restore the original operating system and factory-installed software by using the Restore Plus! CD and any other CDs that came with the computer. Carefully read and follow the instructions provided for the restore solution that came with the computer. For questions about or problems with this CD, please contact customer support. Turning Off the Computer To properly turn off the computer, first shut down the operating system software. In Microsoft Windows XP Professional and Microsoft Windows 2000 Professional, click Start > Shut Down. In Microsoft Windows XP Home, click Start > Turn Off Computer. The computer automatically shuts down. Depending on the operating system, pressing the power button causes the computer to enter a low-power or “standby” state instead of automatically turning the power off. This allows you to conserve energy without closing software applications; later, you can start using the computer immediately without having to restart the operating system and without losing any data. Ä CAUTION: Manually forcing the computer off can cause loss of data.

for four seconds. However, manually turning off the power bypasses the standby state and can result in loss of data. To reconfigure the power button to work in On/Off mode, run Computer Setup. Refer to the Computer Setup Guide on the Documentation Library CD for more information about using the Computer Setup utility. Working with the MultiBay The MultiBay is a special drive bay that supports a variety of optional 12.7-mm removable drives, including: ■ MultiBay CD-ROM Drive ■ MultiBay CD-RW Drive ■ MultiBay DVD-ROM Drive with Software MPEG-2 ■ MultiBay CD-RW/DVD-ROM Combo Drive ■ MultiBay 1.44-MB Diskette Drive ■ MultiBay SMART Hard Drive Ä CAUTION: To prevent loss of work and damage to the computer or a drive: ■ Before handling a drive, ensure that you are discharged of static electricity. While handling a drive, avoid touching the connector. ■ Before traveling with, shipping, storing, or removing a drive other than a hard drive, make sure that no media, such as a diskette, CD-ROM, or DVD-ROM, is in the drive and that the media tray is closed. ■ Handle a drive carefully: do not use excessive force when inserting it, do not drop it, and do not press on the top cover. ■ Avoid exposing a hard drive to liquids, temperature extremes, or products that have magnetic fields such as monitors or speakers. ■ If a drive must be mailed, place the drive in a bubble-pack mailer or other suitable protective packaging and label the package “Fragile: Handle with Care.”

Ä CAUTION: To prevent damage to the computer, the drive, and any data stored on the drive: If you are inserting or removing a hard drive, shut down the computer. Never remove a hard drive while the computer is on or on standby. To ensure that the computer is not on standby, turn the computer on, then shut it down. Ä CAUTION: After inserting an optical drive while the computer is powered on, restart the computer to ensure the optical drive functions correctly if it uses recording, backup, or video playback software applications. If the computer is running Windows 2000 or Windows XP, you can insert or remove any drive except a hard drive while the computer is on, off, or on standby. Hot-swapping is disabled, by default, for the MultiBay 1.44-MB Diskette Drive. To enable hot-swapping, complete the following steps: 1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart the Computer. 2. When the F10 = Setup message is displayed in the lower-right corner of the screen, press the F10 key. ✎ If you do not press the F10 key while the message is displayed, you must restart the computer again to access the utility. 3. Select the language from the list and press the Enter key. A choice of five headings appears in the Computer Setup Utilities menu: File, Storage, Security, Power, and Advanced. 4. Use the arrow keys to select Advanced > Power-on Options > Hot-Pluggable MB Floppy, then click Enable. 5. To apply and save changes, click File > Save Changes and Exit. For more information about using Computer Setup, refer to the Computer Setup (F10) Utility Guide.

1. Exit all software applications, shut down the operating system software, and turn off the computer. 2. Insert the hard drive into the MultiBay. Refer to “Inserting a Drive into the MultiBay” for more information. 3. Turn on the computer. Follow directions for the operating system, below: Windows 2000 Professional 1. Right-click the My Computer icon, then click Manage > Disk Management. 2. Select the MultiBay hard drive. 3. On the Partition menu, click Create. Carefully read and respond to any prompts that appear on the screen. Refer to the Microsoft Management Console online help (click Action > Help, while running Management Console) for additional information. Windows XP Professional 1. Click Start. 2. Right-click My Computer, then click Manage. 3. Click Storage, then click Disk Management. 4. Select the MultiBay hard drive. 5. Right-click on the MultiBay hard drive, then click Partition. Carefully read and respond to any prompts that appear on the screen. Refer to the online Help (click Action > Help) for additional information.

1. Exit all software applications, shut down the operating system software, and turn off the computer if you are inserting or removing a hard drive. 2. Remove any removable media, such as a compact disc, from the drive. 3. With the top of the drive facing up (or left, when the computer is in the minitower position) and the drive connector facing the computer, slide the drive into the MultiBay and push firmly to ensure that the electrical connector is properly seated. 4. After inserting an optical drive while the computer is powered on, restart the computer to ensure the optical drive functions correctly if it uses recording, backup, or video playback software applications. 5. Engage the MultiBay security catch, if desired. See “Engaging and Releasing the MultiBay Security Catch” for more information. Inserting a Drive into the MultiBay

are installed on the system. If they are not available, they may be downloaded, at no cost, from the HP Web site at www.hp.com. Engaging and Releasing the MultiBay Security Catch When engaged, the MultiBay security catch disables the MultiBay eject lever, so that a drive installed in the MultiBay cannot be removed. 1. To secure a drive in the MultiBay, you must first remove the top access panel. Refer to the Hardware Reference Guide on the Documentation Library CD for more information. 2. Slide the catch toward the rear of the computer until it is engaged. Engaging the MultiBay Security Catch

top access panel. Refer to the Hardware Reference Guide on the Documentation Library CD for more information. 2. Lift the tongue of the catch up and slide the catch toward the front of the computer until it is disengaged. Releasing the MultiBay Security Catch Removing a Drive from the MultiBay 1. Exit all software applications, shut down the operating system software, and turn off the computer if you are inserting or removing a hard drive. 2. Release the MultiBay security catch, if it has been engaged. See “Engaging and Releasing the MultiBay Security Catch” for more information. 3. Before removing an optical or diskette drive, stop the drive using the Safely Remove Hardware icon on the Windows XP task bar or the Unplug or Eject Hardware icon on the Windows 2000 task bar.

the drive from the MultiBay 2. Removing a Drive from the MultiBay Finding More Information Refer to the Documentation Library CD for additional product information in easy to access PDF format. The CD contains the following publications: ■ Quick Setup (available in print and Adobe Acrobat PDF on the library CD) Helps you connect the computer and peripheral devices. ■ Getting Started (available in print and PDF on library CD) Helps you set up factory-provided software; also includes basic troubleshooting information should you encounter any problems during initial startup.

Provides an overview of the product hardware as well as instructions for upgrading this series of computers and includes information on RTC batteries, memory, and power supply. ■ Computer Setup (F10) Utility Guide (PDF on library CD) Provides instructions on using this tool to reconfigure or modify default settings for maintenance purposes or when installing new hardware devices. ■ Desktop Management Guide (PDF on library CD) Provides definitions and “how to” instructions for security and Intelligent Manageability features that are preinstalled on select models. ■ Network & Internet Communications Guide (PDF on library CD) Provides basic networking information and instructions for installing device drivers and using network interface controller (NIC) features preinstalled on select desktop models; also provides information about Internet Service Providers and using the Internet. ■ Troubleshooting Guide (PDF on library CD) A comprehensive guide for the customer that provides helpful hints for troubleshooting this computer and scenarios for resolving possible hardware or software problems; includes information about diagnostic codes, as well as information on running Computer Diagnostics for Windows. ■ Safety & Regulatory Information Guide (PDF on library CD) Provides safety and regulatory information that ensures compliance with U.S. Canadian, and various international regulations. ✎ If you do not have a CD-ROM drive, you may download the product documentation from http://www.hp.com. Click support & drivers > Compaq reference library. Locating Regulatory Information The computer is a Class B digital device, pursuant to Part 15 of the FCC Rules. Refer to the Safety & Regulatory Information guide on the Documentation Library CD for Class B information.

1. Insert the compact disc into the CD-ROM drive. There may be a slight delay while the software on the CD checks the Windows Regional Settings. If a recent version of Adobe Acrobat or Acrobat Reader is not found on the computer, it will be installed automatically from the CD. 2. Read and follow the prompts to complete the installation. The menu and books are displayed in the language chosen during initial system setup or as specified later in the Windows Regional Settings. If the Regional Settings do not match one of the languages supported on the CD, the menu and books are displayed in English. 3. Click the title of the book you want to read. If there is no CD-ROM drive activity for two minutes or more, it may be that Autorun is not enabled on the computer. To run the Documentation Library CD if it does not run automatically: 1. Click Start > Run. 2. Type: X:\DocLib.exe (where X is the drive letter designator for the CD-ROM drive) 3. Click OK. If the computer is running a Linux operating system, the Documentation Library CD will not autorun. To find additional hardware documentation for the computer, browse to the HelpFiles folder on the CD. To view the documents on the CD, download and install Adobe Acrobat Reader for Linux from www.adobe.com.

If you are having problems with the computer, try the following solutions before calling for technical support. ■ Look for flashing LEDs on the front of the computer that are codes for specific problems. Refer to “Interpreting Diagnostic Lights and Audible Codes” in this guide for details. ■ If the screen is blank, plug the monitor into a different video port on the computer if one is available. Or, change out the monitor with a monitor that you know is working properly. ■ If you are working on a network, plug another computer with a different cable into the network connection. There may be a problem with the network plug or cable. ■ If you recently added new hardware, remove the hardware and see if the computer functions properly. ■ If you recently installed new software, uninstall the software and see if the computer functions properly. ■ Refer to the following “Helpful Hints” section in this guide for more general suggestions. ■ Refer to the comprehensive Troubleshooting Guide on the Documentation Library CD for more detailed information. ■ Refer to the comprehensive online technical support at http://wwss1pro.compaq.com/support/home/index.asp ■ Run the Restore Plus! CD. If it becomes necessary to call for technical assistance (1-800-652-6672), be prepared to do the following to ensure that your service call is handled properly: ■ Be in front of your computer when you call. ■ Write down the computer and monitor serial numbers before calling and have them readily available. ■ Be prepared to spend the time necessary troubleshooting the problem with the service technician.

1-800-282-6672. Helpful Hints If you encounter some minor problem with your computer, monitor, or software, refer to the following list of general suggestions before taking further action: ■ Check that the computer and monitor are plugged into a working electrical outlet. ■ Check to see that the voltage select switch is set to the appropriate voltage for your region (115V or 230V). ■ Check to see that the computer is turned on and the green power light is on. ■ Check to see that the monitor is turned on and the green monitor light is on. ■ Look for flashing LEDs on the front of the computer. The flashing lights are error codes that will help you diagnose the problem. Refer to Appendix A in the Troubleshooting Guide on the Documentation Library CD for more information. ■ Turn up the brightness and contrast controls of the monitor if the monitor is dim. ■ Press and hold any key. If the system beeps, then your keyboard is operating correctly. ■ Check all cable connections for loose connections or incorrect connections. ■ Wake the computer by pressing any key on the keyboard or pressing the power button. If the system remains in suspend mode, shut down the computer by pressing and holding the power button for at least four seconds, then press the power button again to restart the computer. If the system will not shut down, unplug the power cord, wait a few seconds, then plug it in again. If it does not restart automatically, press the power button to start the computer.

expansion board or other option. See “Solving Hardware Installation Problems” for instructions. ■ Be sure that all the needed device drivers have been installed. For example, if you have connected a printer, you need to install a printer driver. ■ Remove all diskettes from your system before turning it on. ■ If you have installed an operating system other than the factory-installed operating system, check to be sure that it is supported on your system. ■ If your computer has multiple video sources (embedded, PCI, or AGP adapters) installed (embedded video on select models only) and a single monitor, the monitor must be plugged into the monitor connector on the source selected as the primary VGA adapter. During startup, the other monitor connectors are disabled; if the monitor is connected into one of these ports, it will not function. You can select the default VGA source in Computer (F10) Setup. Ä CAUTION: When the computer is plugged into an AC power source, voltage is always being applied to the system board. You must disconnect the power cord from the power source before opening the computer to prevent system board or component damage. Basic Troubleshooting This section concentrates on problems that you might encounter during the initial set up process. A comprehensive Troubleshooting Guide is available on the Documentation Library CD and under the reference library at the following Web site: http://www.hp.com/support.

You may be able to easily resolve the general problems described in this section. If a problem persists and you are unable to resolve it yourself or if you feel uncomfortable about performing the operation, contact an authorized dealer or reseller. Solving General Problems Problem Cause Solution Computer appears locked up and will not turn off when the power button is pressed. Software control of the power switch is not functional. Press and hold the power button for at least four seconds until the computer turns off. Computer will not respond to USB keyboard or mouse. Computer is in standby mode. Press the power button to resume from standby mode. Ä CAUTION: When attempting to resume from standby mode, do not hold down the power button for more than four seconds. Otherwise, the computer will shut down and you will lose your data. Computer date and time display is incorrect. RTC (real-time clock) battery may need to be replaced. ✎Connecting the computer to a live AC outlet prolongs the life of the RTC battery. First, reset the date and time under Control Panel (Computer Setup can also be used to update the RTC date and time). If the problem persists, replace the RTC battery. See the Hardware Reference Guide for instructions on installing a new battery, or contact an authorized dealer or reseller for RTC battery replacement. Computer appears to pause periodically. Network driver is loaded and no network connection is established. Establish a network connection, or use Computer Setup or Microsoft Windows Device Manager to disable the network controller. Cursor will not move using the arrow keys on the keypad. The Num Lock key may be on. Press the Num Lock key. The Num Lock light should not be on if you want to use the arrow keys. The Num Lock key can be disabled (or enabled) in Computer Setup.

access panel. Smart Cover Lock, featured on some computers, is locked. Unlock the Smart Cover Lock using Computer Setup. The Smart Cover FailSafe Key, a device for manually disabling the Smart Cover Lock, is available from HP. You will need the FailSafe Key in case of forgotten password, power loss, or computer malfunction. Poor performance is experienced. Processor is hot. 1. Make sure the airflow to the computer is not blocked. 2. Make sure the fans are connected and working properly (some fans only operate when needed). 3. Make sure the processor heatsink is installed properly. Hard drive is full. Transfer data from the hard drive to create more space on the hard drive. Computer powered off automatically and the Power LED flashes Red two times, once every second, followed by a two second pause. Processor thermal protection activated: A fan may be blocked or not turning. OR The heatsink is not properly attached to the processor. 1. Ensure that the computer air vents are not blocked and the cooling fan is running. 2. Open hood, press power button, and see if the processor fan spins. If the processor fan is not spinning, make sure the fan's cable is plugged onto the system board header. Ensure the fan is fully/properly seated or installed. 3. If fan is plugged in and seated properly, but is not spinning, then replace the processor fan. 4. Reseat processor heatsink and verify that fan assembly is properly attached. 5. Contact an authorized reseller or service provider. Solving General Problems (Continued) Problem Cause Solution

on and the LEDs on the front of the computer are not flashing. System unable to power on. Press and hold the power button for less than 4 seconds. If the hard drive LED turns green, then: 1. Check that the voltage selector, located on the rear of the power supply, is set to the appropriate voltage. Proper voltage setting depends on your region. 2. Remove the expansion cards one at a time until the 3.3 V_aux light on the system board turns on. 3. Replace the system board. OR Press and hold the power button for less than 4 seconds. If the hard drive LED does not turn on green then: 1. Check that unit is plugged into a working AC outlet. 2. Open hood and check that the power button harness is properly connected to the system board. 3. Check that both power supply cables are properly connected to the system board. 4. Check to see if the 3.3 V_aux light on the system board is turned on. If it is turned on, then replace the power button harness. 5. If the 3.3 V_aux light on the system board is not turned on, then replace the power supply. 6. Replace the system board. Solving General Problems (Continued) Problem Cause Solution

You may need to reconfigure the computer when you add or remove hardware, such as an additional diskette drive. If you install a plug and play device, Windows 2000 and Windows XP automatically recognize the device and configure the computer. If you install a non–plug and play device, you must reconfigure the computer after installing the new hardware. In Windows 2000, select the Add New Hardware icon in the Control Panel (for Windows XP, use the Add Hardware Wizard) and follow the instructions that appear on the screen. Solving Hardware Installation Problems Problem Probable Cause Recommended Solution A new device is not recognized as part of the system. Device is not seated or connected properly. Ensure that the device is properly and securely connected and that pins in the connector are not bent down. Cable(s) of new external device are loose or power cables are unplugged. Ensure that all cables are properly and securely connected and that pins in the cable or connector are not bent down. Power switch of new external device is not turned on. Turn off the computer, turn on the external device, then turn on the computer to integrate the device with the computer system. When the system advised you of changes to the configuration, you did not accept them. Reboot the computer and follow the instructions for accepting the changes. A plug and play board may not automatically configure when added if the default configuration conflicts with other devices. Use Windows 2000 or Windows XP Device Manager to deselect the automatic settings for the board and choose a basic configuration that does not cause a resource conflict. You can also use Computer Setup to reconfigure or disable devices to resolve the resource conflict.

Wrong memory modules were used in the upgrade or memory modules were installed in the wrong location. 1. Review the documentation that came with the system to determine if you are using the correct memory modules and to verify the proper installation. 2. Observe the beeps and LED lights on the front of the computer. See “Interpreting diagnostic Lights and Audible Codes” to determine possible causes. 3. If you still cannot resolve the issue, contact Customer Support. Power LED flashes Red five times, once every second, followed by a two second pause, and the computer beeps five times. Memory is installed incorrectly or is bad. 1. Reseat DIMMs. Power on the system. 2. Replace DIMMs one at a time to isolate faulty module. 3. Replace third-party memory with HP memory. 4. Replace the system board. Power LED flashes Red six times, once every second, followed by a two second pause, and the computer beeps six times. Video card is not seated properly or is bad, or system board is bad. For systems with a graphics card: 1. Reseat the graphics card. Power on the system. 2. Replace the graphics card. 3. Replace the system board. For systems with integrated graphics, replace the system board. Solving Hardware Installation Problems (Continued) Problem Probable Cause Recommended Solution

This section covers the front panel light (LED) codes as well as the audible codes that may occur before or during the Power-On Self-Test (POST) that do not necessarily have an error code or text message associated with them. ✎ If you see flashing LEDs on a PS/2 keyboard, look for flashing LEDs on the front panel of the computer and refer to the following table to determine the front panel LED codes. ✎ Recommended actions in the following table are listed in the order in which they should be performed. Diagnostic Front Panel Lights (LEDs) and Audible Codes Activity Beeps Possible Cause Recommended Action Green Power LED On. None Computer on. None Green Power LED flashes every two seconds. None Computer in Suspend to RAM mode (select models only) or normal Suspend mode. None Green Power LED flashes four times, once per second. None Computer in Suspend to Disk or “Hibernate” mode. None

flashes two times, once every second, followed by a two-second pause. None Processor thermal protection activated: A fan may be blocked or not turning. OR The heatsink/fan assembly is not properly attached to the processor. 1. Ensure that the computer air vents are not blocked and the cooling fan is running. 2. Open hood, press power button, and see if the processor fan spins. If the processor fan is not spinning, make sure the fan's cable is plugged onto the system board header. Ensure the fan is fully/properly seated or installed. 3. If fan is plugged in and seated properly, but is not spinning, then replace processor fan. 4. Reseat processor heatsink and verify that fan assembly is properly attached. 5. Contact an authorized reseller or service provider. Red Power LED stays on. None Processor not installed (not an indicator of bad processor). 1. Check to see that the processor is present. 2. Reseat the processor. Diagnostic Front Panel Lights (LEDs) and Audible Codes (Continued) Activity Beeps Possible Cause Recommended Action

flashes once every two seconds. None Power failure (power supply is overloaded). 1. Check that the voltage selector, located on the rear of the power supply, is set to the appropriate voltage. Proper voltage setting depends on your region. 2. Open the hood and ensure the 4-wire power supply cable is seated into the connector on the system board. 3. Check if a device is causing the problem by removing ALL attached devices (such as hard, diskette, or optical drives, and expansion cards.) Power on the system. If the system enters the POST, then power off and replace one device at a time and repeat this procedure, until failure occurs. Replace the device that is causing the failure. Continue adding devices one at a time to ensure all devices are functioning properly. 4. Replace the power supply. 5. Replace the system board. Red Power LED flashes five times, once every second, followed by a two second pause. 5 Pre-video memory error 1. Reseat DIMMs. Power on the system. 2. Replace DIMMs one at a time to isolate faulty module. 3. Replace third-party memory with HP memory. 4. Replace the system board. Diagnostic Front Panel Lights (LEDs) and Audible Codes (Continued) Activity Beeps Possible Cause Recommended Action

flashes six times, once every second, followed by a two second pause. 6 Pre-video graphics error. For systems with a graphics card: 1. Reseat the graphics card. Power on the system. 2. Replace the graphics card. 3. Replace the system board. For systems with integrated graphics, replace the system board. Red Power LED flashes seven times, once every second, followed by a two second pause. 7 System board failure (ROM detected failure prior to video). Replace the system board. Red Power LED flashes eight times, once every second, followed by a two-second pause. 8 Invalid ROM based on bad checksum. 1. Reflash the ROM using a ROMPaq diskette. See the “ROM Flash” section of the Desktop Management Guide on the Documentation Library CD. 2. Replace the system board. Diagnostic Front Panel Lights (LEDs) and Audible Codes (Continued) Activity Beeps Possible Cause Recommended Action

power on and LEDs are not flashing. None System unable to power on. Press and hold the power button for less than 4 seconds. If the hard drive LED turns green, then: 1. Check that the voltage selector, located on the rear of the power supply, is set to the appropriate voltage. Proper voltage setting depends on your region. 2. Remove the expansion cards one at a time until the 3.3 V_aux light on the system board turns on. 3. Replace the system board. OR Press and hold the power button for less than 4 seconds. If the hard drive LED does not turn on green then: 1. Check that unit is plugged into a working AC outlet. 2. Open hood and check that the power button harness is properly connected to the system board. 3. Check that both power supply cables are properly connected to the system board. 4. Check to see if the 3.3 V_aux light on the system board is turned on. If it is turned on, then replace the power button harness. 5. If the 3.3 V_aux light on the system board is not turned on, then replace the power supply. 6. Replace the system board. Diagnostic Front Panel Lights (LEDs) and Audible Codes (Continued) Activity Beeps Possible Cause Recommended Action

You may elect to purchase the Quick Troubleshooting Guide that contains easy to follow flow charts that lead you through the debugging process. This guide was written for authorized service providers and contains steps that may be beyond the technical capabilities of some users. Improperly performing some processes identified in the guide may damage the computer and/or void the warranty. If you are unsure of your ability to perform the task, or if you are concerned about voiding the product warranty, contact your local authorized sales or service representative before undertaking the recommended corrective action. To order the Quick Troubleshooting Guide, use the following part numbers: ■ Part number 153837-001 for single copies ■ Part number 153838-001 for multiples of five Authorized dealers, resellers, and service providers should use the normal procedure for ordering spare parts. Customers in the U.S. and Canada should call 1-800-952-7689. In other countries, contact your local HP office for availability.