Lorex HTC Wildfire S Quick Setup Manual

under 15 minutes Hand Tools Hard Rout Time: 20 Minutes Hand Tools Ski BASIC INSTALLATION GU Digital Video Surveillance Recorder ECO LH110 Series Quick Setup Guide ATTENTION: • This guide refers only to the DVR set-up. • DVR model, number of channels/port configuration and HDD (hard disk drive) capacity may vary by model. Check your package for specific content information. • Monitor and cameras are not included. • Broadband router and computer are required for local and remote monitoring (not included). For detailed setup information, please refer to your included User’s Manual. For additional information, please visit our website www.lorextechnology.com Information in this document is subject to change without notice. As our products are subject to continuous improvement, Lorex Technology Inc. and our subsidiaries reserve the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE © 2011 LOREX. All rights reserved. * For setup of Instant Mobile Viewing refer to your User Manual. It’s all on the Web Instant Mobile Viewing 1 X Eco Digital Video Recorder With Pre-Installed HDD* 1 X USB Mouse 1 X Power Adapter 1 X Remote Control 1 X Ethernet Cable 1 X Instruction Manual 1 X Quick Start Guide 1 X CD PACKAGE CONTENTS: 2 Connecting the USB Mouse Connect the USB mouse to the top USB port on the back panel of the DVR. 4 Connecting the Ethernet Cable Connect one end of the Ethernet cable to an available LAN port of your router (not included) and the other end to the DVR’s Network Port. 5 Powering ON the DVR Connect the power cable to the DC 12V port on the rear panel and the power cord into an electrical outlet. The system turns on automatically once the power cord is plugged in. At startup, the system performs a basic system check and runs an initial loading sequence. After a few moments, the system loads a live display view. Note: Make sure al and cables are prope connected prior to po on the system. Note: If your monitor is not automatically detected, the DVR f buttons, mouse and remote control may not respond. To fix t press “0” three times on the remote control. Alternatively, you and hold the (rewind) button (on 4 and 8 channel units) button (on 16 channel units) on the DVR front panel until you he For more information, please refer to the User’s Manual. 3a Connecting a Monitor (not included) Connect the VGA cable (not included) from your LCD monitor to the VGA port on the rear panel of the DVR. 3b From one of the VIDEO OUTPUT ports connect a BNC terminated cable (not included) to a TV or CCTV monitor. OR Connecting Cameras (not included) 1 Connect BNC cameras to the BNC ports (VIDEO INPUT) on the rear panel. NOTE: Test the cameras prior to selecting a permanent mounting location by temporarily connecting the cameras and cables to your DVR. NOTE: the four ch model is shown BASIC SETUP STEP 1

INTERNET REMOTE MONITORING Continued 5 Open your web browser (Internet Explorer by default enter http://www.lorexddns.net in the address bar. DDNS (Dynamic Domain Name System) Se http://www.lorexddns.ne 1. Insert the system’s software CD, and follow the instructions to launch the Lorex Auto Port Forwarding Wizard software. Installation 2 1: Populate the Router Database 3 The Auto Port Forwarding Wizard automatically populates a list of current routers, and detects the number of connected routers. 1. Click the Next button after the software detects your router configuration. 2. Under Router IP, click the Detect Router IP button. The router’s IP populates in the blank field. 3. Under Username and Password, enter the router’s username and password. 4. Under IP, enter the IP address of your Lorex device as recorded in Step 3-1. 5. Under Port, enter the port number(s) that require forwarding (80, 9000, 1025). 6 Click Next to continue NOTE: Click the Auto Detect button if you have a Linksys or Netgear router (this works with most models). 2: Enter your Router Settings 80 9000 1025 1. Under the Router drop-down list, select the model of your router OR click the Search button to enter the name of your router model. Note: Ensure you select the proper model and firmware number of the router (as it appears on the back of the router) IMPORTANT: Default ports that must be port forwarded for remote access: Port 80 (Web Port) Port 9000 (Media RTSP Streaming Port) Port 1025 (Mobile Connectivity Port) 4: Test your Connection 1. Click the Test Your Connection button. Your sy default browser opens and connects to your Lorex NOTE: Ensure that Internet Explorer is your system default internet browser. 3: Update the Router Settings 1. Click the Update Router button. The program begins updating the router settings. This may take 20 - 30 seconds. 2. Close the update window when the update finishes. Note: You may have to manually save your router settings after the software makes the required changes to your router. Auto Port Forward Wizard 1 The Lorex Auto Port Forwarding Wizard is a software that automates router port forwarding. NOTE: You must be on the same network as the DVR when setting up the DDNS. You must have the following before you configure the software: 1. Your router’s model and version numbers 2. Your router’s user name and password 3. Your Lorex device’s IP address (recorded in Step 3-1) 4. Your Lorex device’s port numbers that require port forwarding (80, 9000, 1025) Optional: Manual Port Forward 4 If you were unable to port-forward your r automatically using the wizard, you will n do so manually. All routers are different. To port forward your router, ple to your router’s user manual. An example of a port forwarding screen is shown for illustration purposes. 80 80 Web EXAMPLE 9000 12 12 Media 9000 1025 12 Mobile 1025 STEP 4 STEP 4 REMOTE INSTALLATION GUIDE Time: 20 Minutes Skills - Intermediate Hardware: PC Skill Level Intermediate easy advanced Time under 30 minutes under 15 minutes under 60 minutes Hand Tools Hardware Router Hi Speed over 60 minutes