Hussmann F6 Assembly Manual

2-Foot Starter Bumper Internal Joint Trims Start at the left end with the Internal Joint Trims and the 2-Foot Starter Bumper. Full Length Bumper 2-Foot Starter Bumper Lower Bumper 2-Foot Starter Bumper Upper Bumper Full Length Bumper 10 Merchandisers ® HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. P/N 0416185B 10 OFFSETTING BUMPERS 1. Locate 2-foot starter bumpers. 2. Remove factory installed top rails and bumpers from cases. Be careful not to lose the internal joint trims on the bumpers. 3. Starting at the left end of the line up, install the 2-foot starter bu ...

6 Apply ButylTape (Item – 11) across the bottom joint. Use field supplied silicone in any gap between front support brackets. See Figure 6. 7 INSTALLING SPLASH GUARDS AND BRACKETS. After the merchandisers have been leveled and joined and all drip piping, electrical and refrig- eration work has been completed, the installation of the splashguards may be started. A. First, check that the Splashguard Retainers are properly attached to the splash- guard brackets and that the brackets are level with the floor. ...

11 On the left end of the line up position the starter section of the top rail as shown in Figure 14, Detail H-1. Push bottom of the short top rail down over the color panel and lift the top with the other hand as shown in Detail H-1. 12 Use one hand to push the top rail toward the rear of the case while using the other hand to “snap” the top section down over the edge of the light channel as shown in Detail H-2 and H-3. REFRIGERATE CASE LINEUP AND LAST SECTIONS FOR AT LEAST 6 HOURS. Leave all bumper sections on with cases operating ...

Figure 5. Bolting Cases at the Baffle Bolt cases together here using Items 7, 8 and 9. Baffle Multi-deck Frozen Food Joining Instructions Note: At the bottom back position (C), join at the coil by-pass baffle area using the special bracket provided. See Figure 5 for more detail regarding this area of joining. Next, fasten upper front and back of the case together at locations D, E and F using Cap Screw (Item) – 7 with Flat Washers (Item – 8) and Lock Washers (Item – 9) Refer to Figure 4, Detail C. Repeat this sequence ...

C E F A D B F Figure 4. Joining Cases FASTEN IN SEQUENCE SHOWN. 7 8 9 10 Use fasteners at locations A, B and C. DETAIL B 4 Snap a chalk line to use as a guide for positioning the front of the cases. The front base frame should be on the chalk line. Next, move the second merchandiser against first, mating with corre- sponding holes; also mate the alignment of the bumper joining holes. Push the cases together, then level and shim the second case as needed. BOLTING THE CASES TOGETHER 5 First, fasten lower fron ...

2-Foot Starter Bumper Internal Joint Trims Start at the left end with the Internal Joint Trims and the 2-Foot Starter Bumper. Full Length Bumper 2-Foot Starter Bumper Lower Bumper 2-Foot Starter Bumper Upper Bumper Full Length Bumper 10 Merchandisers ® HUSSMANN CORPORATION, Bridgeton, MO 3044-2483 U.S.A. P/N 0416185B 10 OFFSETTING BUMPERS 1. Locate 2-foot starter bumpers. 2. Remove factory installed top rails and bumpers from cases. Be careful not to lose the internal joint trims on the bumpers. 3. Starting at the left end of the line up, install the 2-foot starter bu ...

Figure 5. Bolting Cases at the Baffle Bolt cases together here using Items 7, 8 and 9. Baffle Multi-deck Frozen Food Joining Instructions Note: At the bottom back position (C), join at the coil by-pass baffle area using the special bracket provided. See Figure 5 for more detail regarding this area of joining. Next, fasten upper front and back of the case together at locations D, E and F using Cap Screw (Item) – 7 with Flat Washers (Item – 8) and Lock Washers (Item – 9) Refer to Figure 4, Detail C. Repeat this sequence ...