Hyundai D46KFA Operation & User’s Manual

STATEMENT INFORMATION TO THE USER NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. yy Increase the separation between the equipment and receiver. yy Connect the equipment into an outlet of a circuit different from that to which the yy receiver is connected. Consult the dealer or an experienced radio/Monitor technician for assistance. yy Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Connecting of peripherals requires the use of grounded shielded signal cables.

For the following product : All of Digital sigange HYUNDAI IBT provides Manufactured at : (factory name, address) Hyundai IBT Co., Ltd. 106, Apogongdan-gil, Gimcheon-si, Gyeongsangbuk-do, 740-862 Republic of Korea We herewith confirmed to comply with the requirements set put in the Council Directive on the Approximation of the Lows of the Member States relating to Electromagnetic Compatibility Directive (89/336/EEC), Low-Voltage Directive(73/23/EEC , 93/68/EEC) . For the evaluation regarding the Directives, the following standards were applied: EN60065/2002 + A1:2006 + A11:2008 + A2:2010 + A12:2011 EN55022 : 2006 EN55024/A2 : 2003 EN61000-3-2 : 2006 EN61000-3-3 : 2008

Check the product list................................................................................................6 Proper location for product installation...................................................................7 Installing a Bracket....................................................................................................8 Title and function of each part...............................................................................10 Adjusting OSD and explanation of its function....................................................15 Diagnosis..................................................................................................................34 Specifications...........................................................................................................36 * REMOTE CONTROL / RS232C COMMAND SPEC DIGITAL SIGNAGE

effectively and conveniently. • TFT LCD Module adopted • Vivid digital color display • OSD control function • Automatic Image control • Automatic temperature control • High speed response • Built in multi-vision function • Low power consumption • HDMI, DVI, D-Sub input & DVI, D-Sub output This product is designed to ensure user's safety. Avoid the following items to prevent serious electric shot and other dangers. - Do not place wet objects on or around the product or the power cord. - Do not cover or insert anything over or into the ventilation openings. - Do not place in a location where damage can be caused by oil, smoke, high temperature, high humidity, dust etc. - The product is not suitable for use at visual display workplaces according to §2 of the German Ordinance for Work with Visual Display Units. - The main plug of the power supply cord shall remain readily operable. - An apparatus with CLASS I construction shall be connected to a Mains socket outlet with a protective earthing connection. - Make sure that the power cord and other cables are correctly plugged in. - Plug the power cord correctly into the end, do not wobble/jiggle, it may cause electric shock fire.

- Overloaded AC outlets and extension cables are as dangerous as the power cord being damaged, call service engineer for replacement as it may cause electric shock or fire. - Do not use multiple devices in a single power outlet, it may cause overheating or fire. - Do not use or place sharp objects near the LCD surface, as this can cause damage to the screen itself. - When cleaning the LCD screen / Surface, do not use chemical cleaning products as this can seriously damage the special coatings on the screen. Only use water to dampen a soft cloth and lightly clear the screen. - Over time dust deposits can build up inside the product, this can cause the product to overheat thus causing premature malfunction or fire. Please do not attempt to clean the inside of the product yourself, please contact the local service agent. - Do not use alcohol or strong chemical solvent such as methyl, ethyl or a Isopropyl. - In the case of cleaning, be sure to remove the power cord and wipe with a soft dry fabric. - Keep batteries for the remote control out of children's sight. - Batteries should be inserted using the correct polarity (+,-). - Use only new batteries, do not mix old & new. - Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions. - Place unit on a stable bracket or surface. - More than 2 people should work together when moving or installing. - Do not hang on or jump to the product or mounting rack. - When the product is left unused for a long time, be sure to unplug the power cord. - In the case of damage or breakage do not attempt to self repair, please contact local service engineer.

not to move itself or fall down. - On Kiosk Model, make sure to turn off the power before connecting cables. - This manual contains general instructions for the display products only so refer to the provided CD-ROM manual and the driver installation manual for the driver installation instructions for touch screen and/or touch screen itself. - The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. - Shall be connected to a MAINS socket outlet with a protective earthing connection. - The disconnect device shall remain readily operable. - The socket-outlet shall be installed near the equipment and shall be easily accessible. - Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

CAUSE Due to the nature of LCD's property, Afterimage can occur. Afterimage appears when identical frames / images are displayed continuasly. If displayed for prolonged periods of time this can become permanent. PREVENTION When you display a freeze frame for a long time, lower the brightness and contrast (Brightness, 70/ Contrast, 80). Also it can be prevented by using moving frame. COUNTERMEASURES Temporary afterimage can be alleviated by displaying white or moving frame about 10 hours.(But, permanent afterimage cannot be disappeared according to the property of LCD) This method is used to remove temporary afterimage that may occur after displaying a still frame for a certain time.  It can take several minutes or hours to remove afterimage according to the severity. In the case that your cannot avoid displaying identical still image continuously, you can prevent it by displaying moving image for 2 or 3 minutes in every hour. As the brightness of still image and time of display are the cause of afterimage, you are recommended to lower the brightness in that case. ! Above problem shall not be covered by warranty. Be sure to understand

Please check the following components provided with the product after you open the box. Remote control Power Cord HDMI cable HDMI to DVI Cable (Option) CD Manual &Sheet D-SUB Cable RS232C Cable (Option) ! please check the following components provided with the product after you open the box and contact the dealer if any missing. * The contents may vary depending on models and sometimes the contents may be attached on the product.

product installation Portrait Mode 1. Locate the product at least 30cm away from the electric appliance or heating product. 2. The product must be placed at least 10cm away from the wall and ground. 3. Keep the product out of direct ray of light and locate screen not to be reflected by the sunlight. 4. Make sure the mounting rack firmly tightened before installation. ! Please take extra care during installation, it is possible to cause damage if the unit is handled badly or knocked. - Only on some models. - When installing in portrait mode, rotate the monitor clockwise

part 1 Power button ; to turn the power on or off. 2 Input selection button : to select other connected device. 3 Menu button : to display menu or exit from the menu. 4 Select button.  5 To move down in OSD menu. 6 To move up in OSD menu. 7 To move left and control the volume down in OSD menu. 8 To move right and control the volume up OSD menu. POWER SOURCE MENU SELECT VOL 1 2 3 4 5 6 7 8

2 HDMI IN 3 DVI OUT 4 PC D-SUB IN 5 PC D-SUB OUT 6 PC AUDIO IN 7 8 ! UPGRADE Port : *this port is used for upgrade service and not for general users. 9 RS-232C IN 0 RS-232C OUT @ COMPONENT OUT (Y/Pb/Pr) # CVBS OUT $ COMPONENT AUDIO IN (L/R) % SPEAKER OUT ^ COMPONENT IN (Y/Pb/Pr) & CVBS IN * COMPONENT AUDIO IN (L/R) ( AC POWER SWITCH ) AC IN ( )

2 Move up in OSD menu. 3 To move left or control the volume down in OSD menu. 4 To move right or control the volume up in OSD menu. 5 To move down in OSD menu. 6 [ENTER] Select in OSD menu. 7 Display the OSD menu. 8 Close the OSD menu. 9 Display the menu of signal source and choose it. 0 Temporary sound switch off. [TIP] If it doesn’t need to control display by a remote-controller, press button of remote-controller in order following. MENU → SOURCE → EXIT → ▼ → ENTER(↵) * Press button once again in order above so that original condition is returned.          

NO Resolution Horizontal frequency (KHz) Vertical frequency (Hz) 1 480p 640 x 480p 60 2 576p 720 x 576p 50 3 720p 1280 x 720p 50 / 60 4 1080i 1920 x 1080i 50 / 60 5 640 x 480 31.47 59.94 6 800 x 600 37.88 60.32 7 1024 x 768 48.36 60 8 1360 x 768 47.70 60 9 1280 x 1024 63.98 60 10 1920 x 1080 67.50 60 11 1080p 1920 x 1080p 60

NO Resolution Horizontal frequency (KHz) Vertical frequency (Hz) 1 640 x 480 31.47 59.94 2 800 x 600 37.88 60.32 3 1024 x 768 48.36 60.00 4 1360 x 768 47.71 60.00 5 1280 x 1024 63.98 60.00 6 1920 x 1080 67.50 60.00

explanation of its function How to Select the Picture Mode ✔ Menu of PC doesn’t appear on OSD when user uses HDMI and DVI signal. Users can automatically adjust the picture mode according to the input mode. Picture Picture Mode : Custom Custom  High Colour Tone  Middle Size : Low PC  U Select  Enter  Menu 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select “Picture” Icon. “Picture mode” is highlighted. 3. Press ▶ or ↲ buttons to select “Picture mode”. 4. The menu changes in the following order. Custom -> High -> Middle -> Low 5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu.

Picture Users can manually adjust their desired picture 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Picture" Icon. "Picture mode" is highlighted. 3. Press ▲ / ▼ buttons to move to "Custom" and press ▶or ↲ buttons to select "Custom". 4. Select required option by pressing the ▲ / ▼ or ↲ button, then Press◀ / ▶ button to adjust. 5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. - Brightness : Adjust the brightness of the entire picture. - Contrast : Adjust the brightness and darkness of the object and backgrounds. Custom Brightness : 70 Contrast : 80 U Move  Adjust  Menu

1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Picture" Icon. "Picture Mode" is highlighted. 3. Press ▲ / ▼ buttons to move to "Colour Tone" 4. Press ▶ or ↲ buttons to select "Colour Tone" . 5. Press ▲ / ▼ buttons, then the menu changes in the following order. Custom -> Cool2 -> Cool1 -> Normal -> Warm1 -> Warm2 6. Press EXIT button to escape OSD menu or press MENU button to return to the previous menu. - Custom : When the user wants to set the degree of RGB directly. - Cool : For cool colors with bluish tone. - Normal : For a general Colour Tone. - Warm : For warm colors with reddish tone. How to Select a Colour Tone Colour Tone Colour Tone : Normal Red : 50 Green : 50 Blue : 50 U Move  Enter  Menu

How to Set the Display Size ✔ Menu of PC doesn’t appear on OSD when user uses HDMI and DVI signal. Picture Picture Mode : Custom  Colour Tone  Wide Size : 4 : 3 PC  U Select  Enter  Menu 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select “Picture” Icon. “Picture Mode” is highlighted. 3. Press ▲ / ▼ buttons to move to “Size”. 4. Press ◀ / ▶ or ↲ buttons and press ▲ / ▼ then the mode change in the following order. Wide -> 4 : 3 5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. - Wide - General broadcast picture is adjusted to 16:9. - 4 : 3 - 4 : 3 general picture size

in PC mode (Supported only in PC mode) 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Picture" Icon. "Picture Mode" is highlighted. 3. Press ▲ / ▼ buttons to move to PC and press ▶ or ↲ buttons to select to "PC" "Auto Adjust" is high lighted. 4. Press ↲ button to execute the "Auto Adjust" 5. Select the required option by pressing the ◀ / ▶ or ↲ button, then press ◀ / ▶button to adjust 6. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. - Auto Adjust : Horizontal/vertical positions are automatically adjusted. - Phase : To eliminate the shake of the picture. - H-Position : To adjust the horizontal position of the picture. - V-Position : To adjust the vertical position of the picture. - Frequency : To eliminate the shake of picture. - Resolution : Selecting resolution is allowed to only set to 1024x768, 1280x768, 1360x768, 1366x768. Select corresponsive resolution with specified resolution of image. Picture Auto Adjust  Phase : 52 H-Posilion : 16 V-Posilion : 24 Fiequency : -78 Resolution : U Move  Enter  Menu

- Custom : When the user wants to set the values directly. - Standard : For the general sound. Most audio contents are appropriate to this mode. - Music : For enjoying original sound. - Movie : Grandiose sound. - Speech : Clear sound. How to Select the Audio Mode 1. Press Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ buttons to move to “Sound” Icon. 3. Press ↲ button to select “Sound” Icon. “Mode” is highlighted. 4. Press ▶ or ↲ buttons, to select to Sound mode. then the menu changes in the following order. Custom->Standard -> Music -> Movie -> Speech 5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. Sound Mode : Custom Volume : Standard Balance : Music Equalizer  Movie Auto Volume : Speech Sound Mode : HDMI Sound : U Select  Enter  Menu

How to Adjust the Desired Audio Mode 1. Press Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ buttons to move to "Sound" Icon. 3. Press ↲ button to select "Sound" Icon. "Mode" is highlighted. 4. Press ▲ / ▼ buttons to move to "Balance" or "Equalizer" . 5. Press ↲ buttons to select "Balance" or "Equalizer". Balance or Equalizer menu appears. 6. Select required option by pressing the ▲ / ▼ buttons, then Press ◀ / ▶ buttons to adjust. 7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. - Balance : Adjusts the balance of left and right speakers. - Equalizer : Adjusts the audio output signal in the desired band. Sound 10KHz 50 3KHz 50 1KHz 50 300Hz 50 100Hz 50 U Move L Adjust  Menu Sound Mode : Standard Volume : 30 Balance : L50 R50 Equalizer  Auto Volume : Off Sound Mode : Stereo HDMI Sound : HDMI U Move L Adjust  Menu

How to Select Sound Mode This function will automatically give a similar volume size to each channel. 1. Press Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ buttons to move to "Sound" Icon. 3. Press ↲ button to select "Sound" Icon. "Mode" is highlighted. 4. Press ▲ / ▼ buttons to move to "Auto Volume". 5. Press ◀ / ▶ or ↲ buttons to select "On/Off". 6. Press ▲ / ▼ or ↲ buttons to set to "On/Off". 7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu - Choose "Stereo" for channels that are broadcasting in Stereo. - Choose "Mono" for channels that are broadcasting in Mono, or if you are having difficultly receiving a Stereo signal. 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Sound" Icon. "Mode" is highlighted. 3. Press ▲ / ▼ buttons to move to "Sound Mode". 4. Press ▶ or ↲ buttons to select to "Sound Mode". 5. Press ▲ / ▼ buttons to select to "Stereo"," Mono L"or "Mono R. 6. Press exit button to escape OSD MENU or press MENU butto to return to the previous menu Depending on the particular program being broadcast, you can select stereo or mono. Sound Mode : Volume : Balance : Equalizer  On Auto Volume : Off Sound Mode : HDMI Sound : U Select  Enter  Menu Sound Mode : Volume : Balance : Equalizer  Stereo Auto Volume : Mono L Sound Mode : Mono R HDMI Sound : U Select  Enter  Menu

1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select “Sound” Icon. “Mode” is highlighted. 3. Press ▲ / ▼ buttons to move to “HDMI Sound”. 4. Press ▶ or ↲ buttons to select to “HDMI Sound”. 5. Press ▲ / ▼ buttons to select to “DVI”. 6. Press exit button to escape OSD MENU or press MENU button to return to the previous menu Sound Mode : Volume : Balance : Equalizer  Auto Volume : Sound Mode : HDMI HDMI Sound : DVI U Select  Enter  Menu

How to Set Clock,Sleep Time, ON/OFF Time 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Setup" Icon. "Reset" is highlighted. 3. Press ▶ or ↲ buttons to select to "Reset". 4. Press ↲ buttons to choose to "Reset". 5. Press EXIT button to escape OSD MENU or press MENU butto to return to the previous menu. 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Setup" Icon. "Reset" is highlighted. 3. Press ▲ / ▼ buttons to move to "Time". 4. Press ▶ or ↲ buttons to select "Time". Time menu appears, then "Clock" is highlighted. 5. Press ◀ / ▶ buttons to move between Hour, Minute and Press ▲ / ▼ buttons to set Hour, Minute. When you select "Reset" user setting Value will initialize. Setup Reset  Time  Language : OSD Tone : Key Lock : DCR : Pixelshift : U Move  Enter  Menu Setup Reset  Time  Language : English OSD Tone : Off Key Lock : Off DCR : Off Pixelshift : U Move  Enter  Menu

Languages 6. Press ▲ / ▼ buttons to move to "On or Off Timer". 7. Press ▶ or ↲ buttons to select "On or Off Timer" . 8. Press ◀ / ▶ buttons to move between Hour, Minute and on/ off and Press ▲ / ▼ buttons to set Hour, Minute and on/off 9. Press ▲ / ▼ buttons to move to "On Time Volume". 10. Press ◀ / ▶ buttons to adjust Volume. 11. Press ▲ / ▼ buttons to move to "Source" 12. Press ▶ or ↲ buttons to select to "Source" 13. Press ▲ / ▼ buttons to set to Source 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Setup" Icon. "Reset" is highlighted. 3. Press ▲ / ▼ button to move to "Language" and press ▶ or ↲ button to select to “Language”. 4. Press ▲ / ▼ buttons to set to language. 5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. Time Clock : 05 : 00 On Timer : 00 : 00 Off Off Timer : 00 : 00 Off On Time Volume : 20 Source : PC U Move  Enter  Menu Setup Reset  English Time  Japanese Language : Korean OSD Tone : Key Lock : DCR : Pixelshift : U Select  Enter  Menu

Transparency How to Set Key-Lock 1. Press Menu button. Menu items appear on the screen. 2. Press ↲ button to select "Setup" Icon. "Reset" is highlighted. 3. Press ▲ / ▼ buttons to move to "OSD Tone" 4. Press ▶ or ↲ buttons to select to "OSD Tone". 5. Press ▲ / ▼ or ↲ buttons to set to "On/Off". User can lock the control buttons on the front bottom of the Monitor. 1. Press Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ button to move to "Setup" Icon. 3. Press ↲ button to select "Setup" Icon. "Reset" is highlighted 4. Press ▲ / ▼ buttons to move to "Key Lock". 5. Press ▶ or ↲ buttons to select to "Key Lock". 6. Press ▲ / ▼ or ↲ buttons to set to "On/Off". 7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. Setup Reset  Time  Language : Off OSD Tone : On Key Lock : DCR : Pixelshift : U Select  Enter  Menu Setup Reset  Time  Language : OSD Tone : Off Key Lock : On DCR : Pixelshift : U Select  Enter  Menu

1. Press Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ button to move to “Setup” Icon. 3. Press ↲ button to select "Setup" Icon. "Reset" is highlighted. 4. Press ▲ / ▼ buttons to move to “DCR”. 5. Press ▶ or ↲ buttons to select to "DCR". 6. Press ▲ / ▼ or ↲ buttons to set to "On/Off". 7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. Setup Reset  Time  Language : OSD Tone : Key Lock : Off DCR : On Pixelshift : U Select  Enter  Menu

1. Press Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ button to move to “Setup” Icon. 3. Press ↲ button to select "Setup" Icon. "Reset" is highlighted. 4. Press ▲ / ▼ buttons to move to “Pixelshift”. 5. Press ▶ or ↲ buttons to select to "Pixelshift". 6. Press ▲ / ▼ or ↲ buttons to set to "On/Off". 7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. Setup Reset  Time  Language : OSD Tone : Key Lock : DCR : Off Pixelshift : On U Select  Enter  Menu This function prevents image burn-in problem on LCD screen. ✔ When Pixelshift option is on, the image moves on the display periodically. It might be seen like the image pops but not the symptoms of display error.

Function (Example of installation) install 3x2 with 6 units Multi H Set Count : 1 V Set Count : 1 Display Sequence : 1 H Edge ADJ : 0 V Edge ADJ : 0 SET ID : 1 Master : Off Compensation : U Move  Adjust  Menu Multi Temp Control  Multi Function  U Move  Enter  Menu 1. Press Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ button to move to "Multi" Icon. 3. Press ↲ button to select "Mutli" Icon. 4. Press ▲ / ▼ buttons to move to “Mutli Function”. 5. Press ▶ or ↲ buttons to select to “Mutli Function”. 4. Press ▲ / ▼ buttons to set up and change the location of the screen to be displyed. H Set Count/ V Set Count/Display Sequence / H Edge ADJ / V Edge ADJ / SET ID/ Master Product 1 Product 2 Product 3 Product 4 Product 5 Product 6

3 3 3 3 3 3 V Set Count 2 2 2 2 2 2 Display Sequence 1 2 3 4 5 6 H Edge ADJ / V Edge ADJ These are the set up value to make up the un-displayed area of Bezel Part. It can be adjustable according to the contents SET ID It is necessary to control via RS232 communication port on PC. But do not need to set up or change when they are not controlled by PC Master You are recommended to use the Master on state only one of products that you are using Set up Value [Cautions] - In case of connecting the products in series from the input device(HDMI ➔ analog RGB ➔ component ➔ video), a distributor is recommended in order because there may be loss of screen quality. - You are recommended to use the progressive frequency of HDMI in case of using multi- vision function. (It may not be displayed properly when using Video input or interlace frequency)

to the PC in HDMI/DVI mode DVI-OUT DVI-IN DVI-OUT DVI-IN DVI-OUT DVI-IN DVI-OUT DVI-OUT HDMI-IN HDMI-IN HDMI-IN DVI-OUT * When multi-connecting in/out cascade format, loss of display quality can happen. We recommend using a cable distributor. OR DVI-HDMI Cable (not included) HDMI Cable Product 1 Product 2 Product 3

Multi Temp Control  Multi Function  U Move  Enter  Menu Multi H Set Count : V Set Count : Display Sequence : H Edge ADJ : V Edge ADJ : SET ID : Master : Off Compensation : On U Move  Adjust  Menu This function emphasizes the signal level to prevent the signal loss when the displays are chained by HDMI cable. 1. Press Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ button to move to "Multi" Icon. 3. Press ↲ button to select "Mutli" Icon. 4. Press ▲ / ▼ buttons to move to “Mutli Function”. 5. Press ▶ or ↲ buttons to select to “Mutli Function”. 4. Press ▲ / ▼ buttons to move to “Compensation”. 5. Press ▶ or ↲ buttons to select to “Compensation”. 6. Press ▲ / ▼ or ↲ buttons to set to “On/Off”. 7. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu.

temperature Multi Temp Control  Multi Function  U Move  Enter  Menu 1. Press Menu button. Menu items appear on the screen. 2. Press ▲ / ▼ button to move to “Multi” Icon. 3. Press ↲ button to select “Multi” Icon, then “Temp Control” is highlighted. 4. Press ▶ or ↲ buttons to select to “Temp Control”. The current temperature is displayed. 5. Press EXIT button to escape OSD MENU or press MENU button to return to the previous menu. Multi Fan Control : Auto Fan Active Temp : 38 °C Hysteresis : 5 °C Temprature : 32 ℃ U Move  Enter  Menu

Symptoms How to solve the problem Screen displays late after the power is on. It happens not to show the screen noise when the power is on. Therefore it is not a defect. But if the screen doesn't show up within 5 minutes from turning on, please contact the customer center. The screen is too dark or bright? Adjust the brightness or contrast. The screen doesn't show up indicating "Out of range". You are using a signal which is outside the operating frequencies of the product (Unsupported), please change you video signal. when the screen is scrambled. please check the cable connection and the signal generator and contact customer center. Automatic switching-on function is not working / the input data were disapperared when reboot the system after setting up the time Automatic switching-on function is working when the product has been turned off via remote control or power button on main body. It is because that the set- up values are deleted when the power cord is unplugged. The screen and sound are not synchronized Check if the power is on, suspended or is correctly plugged into the outlet. Plug the power cord of other peripheral device to the outlet that the product is being connected.

The screen displays without the sound. check the volume up and down with remote control and audio connection cable No sound from either right speaker or left speaker. Confirm the status of the sound balance on OSD menu and check the connection of speaker cable. Remote control doesn't work. Check if any foreign substances in the sensor and the polarity of battery inserted. If the batteries are drained, replace them with new batteries. PC D-SUB doesn't work. Set up the resolution referring to frequency table of input terminal. And re-boot the system as it supports Plug and Play. Fan on the rear doesn't work Check the status of temperature control on OSD menu The screen doesn't show up when display the multi-vision. check if it is set up to video input. Confirm if Interlace Timing was inputted. ( Refer to the cautions on Page 34 ) • If any problem unsolved by above diagnosis, please call customer center.

Screen size (HxV/mm) D46KFA, D46CFA : 1018.08(H) x 572.67(V) D558FA, D552FA : 1209.6(H) x 680.4(V) Recommended resolution 1920 x 1080 @60Hz Input PIR(option), HDMI, DVI-D(HDMI Connector), D-Sub, PC Audio L/R, RS232C, Component, Component Audio L/R, Composite, Composite Audio L/R Output DVI-D, D-Sub, RS232C, Speaker L/R, Component, Composite Power AC 100- 240V 50/60Hz Consumption (Typical) D46KFA : 140 W D46CFA : TBD D558FA : TBD D552FA : 190 W Operating Temperature 0 ~ 40°C Control type Remote control, key control • Above specification may be changed without prior notification for quality improvement.

1. REMOTE CONTROL WAVE FORM 1) Remote Control System Infrared rey system fosc=455KHZ fc=fosc/2=37.917KHZ 2) Signal code • Transmission - One pulse - Bit Desciption - Flame Interval 2. REMOTE CONTROL KEY CODE TABLE Custom Code : 7788H KEY DATA POWER 0x80 MUTE 0x81 MENU 0x95 EXIT 0x96 SOURCE 0xAC ENTER (↵) 0x8C UP 0x8D DOWN 0x8E LEFT 0x8F RIGHT 0x90 DATA LAYOUT LEAD CODE 9ms 4.5ms 0.56ms 1.125ms Tf Tf Tf=108ms 455KHz 0.56ms 2.25ms CUSTOM CODE LOW CUSTOM CODE HIGH DATA CODE DATA CODE LEAD CODE 9ms 4.5ms 0.56ms 1.125ms Tf Tf Tf=108ms 455KHz 0.56ms 2.25ms CUSTOM CODE LOW CUSTOM CODE HIGH DATA CODE DATA CODE LEAD CODE 9ms 4.5ms 0.56ms 1.125ms Tf Tf Tf=108ms 455KHz 0.56ms 2.25ms CUSTOM CODE LOW CUSTOM CODE HIGH DATA CODE DATA CODE Bit “0” Bit “1” 80 81 8D 8C 8F 95 AC 9O 8E 96

1. CONFIGRATION 1) SPEED : 9600 Baud/s, 8 bit, No parity, 1 Stop bit. 2) Cable Connetion 2. COMMAND FORMAT - SET ID must select from the OSD menu and can’t be select through the COMMAND. - Only one unit can be set as Master unit, select Master ON from the OSD Menu. (DEFAULT OFF) - For viewing COMMAND from Hyper Terminal windows, One unit must set as MASTER ON • Data Format Item HEADER SET ID COMMAND END askii did: xxx- or all- follow 2.2 . hexa 0x64 0x69 0x64 0x3A 0x78 0x78 0x78 0x2D or 0x61 0x6C 0x6C 0x2D follow 2.2 0x2E HEADER : Command head code. SET ID : Set ID. all unit control - “xxx- or all-” unit no : “01 ~ 99” COMMAND : follow 2.2 END : inform end of send data. Example. 1 To power on Set ID No 1 Item HEADER SET ID COMMAND END askii did: 01- pn . hexa 0x64 0x69 0x64 0x3A 0x30 0x31 0x2D 0x70 0x6E 0x2E decimal 100 105 100 58 48 49 45 112 110 46 Example. 2 To FAN on Set ID No 2 Item HEADER SET ID COMMAND END askii did: 02- fn . hexa 0x64 0x69 0x64 0x3A 0x30 0x32 0x2D 0x70 0x6E 0x2E decimal 100 105 100 58 48 50 45 102 110 46 • Command Type Item Command Description hexa Power pn power on 0x70 0x6E pf power off 0x70 0x66 ps on, video out / on, video in / off, video out / off, video in / on, dpms mode 0x54 0x65 0x6D 0x70 Input - Source sd input hdmi 0x73 0x64 sp input pc 0x73 0x70 sc input component 0x73 0x63 sa input av 0x73 0x61 is input source status 0x69 0x73 sv input DVI 0x73 0x76 Remote mtn remote controller active on 0x72 0x6D 0x74 0x6E mtf remote controller active off 0x72 0x6D 0x74 0x66 mts remote controller active status CONTROLER(PC) 1 2 2 3 5 2 3 5 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 9Pin DIN male Rx Tx G Tx Rx G RS232C Cable

“lp:?, am:?, av:?, si:?, pwm:?, mot:?.” - last power, aging, av enable, source, pwm, motion 0x66 0x6F mn model nember ex) model no 1:DID D400 SEC HD. 0x6D 0x6E fv firmware version ex) fw:DID IN HD EU V4.84 110217. 0x66 0x76 dp dpms on / dpms off 0x64 0x70 Factory Color Control cr Enable Color Control Mode 0x63 0x72 q quit (from ir & cr mode) 0x71 sbu sub-brightness 1 step up 0x73 0x62 0x75 sbd sub-brightness 1 step down 0x73 0x62 0x64 rou red offset 1 step up 0x72 0x6F 0x75 rod red offset 1 step down 0x72 0x6F 0x64 gou green offset 1 step up 0x67 0x6F 0x75 god green offset 1 step down 0x67 0x6F 0x64 bou blue offset 1 step up 0x62 0x6F 0x75 bod blue offset 1 step down 0x62 0x6F 0x64 scu sub-contrast 1 step up 0x73 0x63 0x75 scd sub-contrast 1 step down 0x73 0x63 0x64 rgu red gain 1 step up 0x72 0x67 0x75 rgd red gain 1 step down 0x72 0x67 0x64 ggu green gain 1 step up 0x67 0x67 0x75 ggd green gain 1 step down 0x67 0x67 0x64 bgu blue gain 1 step up 0x62 0x67 0x75 bgd blue gain 1 step down 0x62 0x67 0x64 blu backlight value 1 step up 0x62 0x6C 0x75 bld backlight value 1 step down 0x62 0x6C 0x64 Item Command Description hexa Picture Mode pmc picture mode custom 0x70 0x6D 0x63 pmh picture mode high 0x70 0x6D 0x68 pmm picture mode middle 0x70 0x6D 0x68 pml picture mode low 0x70 0x6D 0x6C pbu picture mode custom brightness 1 step upstep up 0x70 0x62 0x75 pbd picture mode custom brightness 1 step upstep down 0x70 0x62 0x64 pcu picture mode custom contrast 1 step up 0x70 0x63 0x75 pcd picture mode custom contrast 1 step down 0x70 0x63 0x64 pcb picture mode custom brightness Brightness 70 (01~100) : ex) pcd70 0x50 0x63 0x62 value 0x50 0x63 0x62 0x37 0x30 pcc blue offset 1 step down Contrast 55 (01~100) : ex) pcc55 0x70 0x63 0x63 value 0x70 0x63 0x63 0x35 0x35 Picture Color tru picture color tone red up 0x73 0x63 0x75 trd picture color tone red down 0x73 0x63 0x64 tgu picture color tone green up 0x72 0x67 0x75 tgd rpicture color tone green down 0x72 0x67 0x64 tbu picture color tone blue up 0x67 0x67 0x75 tbd picture color tone blue down 0x67 0x67 0x64 ptcm picture color tone custom 0x70 0x74 0x63 0x6D ptc2 picture color tone cool2 0x70 0x74 0x63 0x32 ptc1 picture color tone cool1 0x70 0x74 0x63 0x31 ptnl picture color tone normal 0x70 0x74 0x6E 0x6C ptw2 picture color tone warm2 0x70 0x74 0x77 0x32 ptw1 picture color tone warm1 0x70 0x74 0x77 0x31 rgb-r color tone red ex) rgb-r55 0x72 0x67 0x62 0x2D 0x72 value 0x72 0x67 0x62 0x2D 0x72 0x35 0x35 rgb-g color tone green ex) rgb-g56 0x72 0x67 0x62 0x2D 0x67 value 0x72 0x67 0x62 0x2D 0x67 0x35 0x36 rgb-b color tone blue ex) rgb-b45 0x72 0x67 0x62 0x2D 0x62 value 0x72 0x67 0x62 0x2D 0x62 0x34 0x35

0x70 0x63 pw picture size wide 0x70 0x77 otf osd tone off 0x6F 0x74 0x66 otn osd tone on 0x6F 0x74 0x6E at auto adjust 0x61 0x74 rt resolution “ ?x?, h?, v?.” ex) “1920x1080, h47, v60.” 0x72 0x68 Multi Chxvy H Set Count is x, V Set Count is y 0x43 0x68 X Value 0x76 Y Value Nhxvy H Set window is x, V Set window is y 0x4E 0x68 X Value 0x76 Y Value Ehxvy H Edge ADJ is x, V Edge ADJ is y 0x45 0x68 X Value 0x76 Y Value x Display sequence no is x 0x78 fs fan status 0x66 0x65 0x6D 0x70 ft fan active temperature ? : 020~100 ft? “fan active temp [?’C]” 0x66 0x74 Value 0x66 0x74 0x34 0x30 fh fan hysteresis ? : 00~20 fh? “hysteresis temp [?’C]” 0x66 0x68 Value 0x66 0x68 0x30 0x33 ff fan control off 0x66 0x66 fn fan control on 0x66 0x6E fa fan control auto 0x66 0x61 la light sensor auto 0x6C 0x61 lh light sensor high 0x6C 0x68 lm light sensor middle 0x6C 0x6D ll light sensor low 0x6C 0x6C tp temperature “temp: [?’C]” 0x74 0x70 IR ir Enable Ir Mode, can use keyboard buttons as RMC 0x69 0x72 q quit (from ir & cr mode) 0x71 p power 0x70 u up 0x75 n down 0x6E Item Command Description hexa IR j left 0x6A k right 0x6B e enter 0x65 m menu 0x6D x exit 0x78 i input 0x69 r mute 0x72 The others quit (from Ir mode) The others hdcp-s hdcp-status HDCP Vector - x x x x x [Hex] HDCP Index - x x x x [Hex] HDCP Checksum - x x [Hex] 0x68 0x64 0x63 0x2D 0x73 did:all-wn=si Change all units ‘Display Sequence’ to ‘SET ID’ 0x64 0x69 0x64 0x3A 0x61 0x6C 0x6C 0x2D 0x77 0x6E 0x3D 0x73 0x69 0x2E did:allfst-hxvy Set all units to ‘H SET Count’ = x, ‘V SET Count’ = y, Display Sequence’ = ‘Select to SET ID 0x64 0x69 0x64 0x3A 0x61 0x6C 0x6C 0x66 0x73 0x74 0x2D 0x68 X Value 0x76 Y Value 0x2E Error “Error.”