IKEA HJÄLPSAM Operation & User’s Manual

hardness dial to the position 1 or 2. Electronic adjustment 1. Press the on/off button to activate the appliance. 2. Make sure that the appliance is in set- ting mode. Refer to ‘SETTING AND STARTING A PROGRAMME’. 3. Press and hold the programme button until the programme indicator (A) flash- es and the programme indicator (B) comes on. 4. Wait until the programme indicator (B) goes off and the end indicator starts to flash (the programme indicator (A) con- tinues to flash). 5. Press the programme button. • The end indicator flashes intermittent- ly. T ...

2 Filters 3 Rating plate 4 Rinse aid dispenser 5 Detergent dispenser 6 Salt container 7 Water hardness dial 8 Upper spray arm 9 Upper basket Control panel B A 2 1 4 3 1 On/off button 2 Programme indicators 3 Indicators 4 Programme button. Indicators Description End indicator. Salt indicator. This indicator is off while the programme operates. Programmes Programme1) Degree of soil Type of load Programme phases Duration (min) Energy (kWh) Water (l) 2) Heavy soil Crockery, cut- lery, pots and pans Prewash Wash 70 °C Rinses Dry 110 - 120 1. ...

ing operation. Before you contact the Service, refer to the information that follows for a solution to the problem. With some problems, different indicators flash continuously or intermittently at the same time to show an alarm code. Alarm code Problem • The indicator of the set programme flash- es continuously. • The end indicator flashes 1 time intermit- tently. The appliance does not fill with water. • The indicator of the set programme flash- es continuously. • The end indicator flashes 2 times intermit- tently. The appl ...

guarantee? • Normal wear and tear. • Deliberate or negligent damage, dam- age caused by failure to observe operat- ing instructions, incorrect installation or by connection to the wrong voltage, dam- age caused by chemical or electro-chem- ical reaction, rust, corrosion or water damage including but not limited to dam- age caused by excessive lime in the wa- ter supply, damage caused by abnormal environmental conditions. • Consumable parts including batteries and lamps. • Non-functional and decorative parts which do not affect normal use of the ap- plianc ...

When the programme is completed, an in- termittent acoustic signal operates and the end indicator comes on. 1. Press the on/off button to deactivate the appliance. 2. Close the water tap. • Let the dishes become cold before you remove them from the appliance. Hot dishes can be easily damaged. • First remove the items from the lower basket, then from the upper basket. There can be water on the sides and on the door of the appliance. Stainless steel becomes cool more quickly than the dishes. Hints and tips The water softener Hard water contains a high quantity of ...

ing operation. Before you contact the Service, refer to the information that follows for a solution to the problem. With some problems, different indicators flash continuously or intermittently at the same time to show an alarm code. Alarm code Problem • The indicator of the set programme flash- es continuously. • The end indicator flashes 1 time intermit- tently. The appliance does not fill with water. • The indicator of the set programme flash- es continuously. • The end indicator flashes 2 times intermit- tently. The appl ...

Type of load Programme phases Duration (min) Energy (kWh) Water (l) 3) Fresh soil Crockery and cutlery Wash 60 °C Rinse 30 0.8 8 4) Normal soil Crockery and cutlery Prewash Wash 50 °C Rinses Dry 120 - 130 0.8 - 0.9 12 - 13 5) All Prewash 11 0.1 5 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the programme duration and the consumption values. 2) This programme has a high temperature rinsing phase for better hygiene results. During the rinsing phase, the temperature stays at ...

not drain the water. The sink spigot is clogged. Clean the sink spigot. The water drain hose has a kink or a bend. Make sure that the position of the hose is correct. The salt indicator con- tinues to stay on after the replenishment of the salt container. This can occur when you are using salt that needs more time to dissolve. There is no unwanted effect on the performance of the appli- ance. If after 3 or 4 programmes, the salt indicator continues to stay on, contact the service. After the checks are completed, activate the appliance ...