InFocus LP130 Operation & User’s Manual

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communi- cations. Operation of this equipment in a residential area is likely to cause harm- ful interference in which case the user will be required to correct the interference at his own expense. Canada This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Can- ada. Safety Certifications UL, CUL, TÜV, NOM, IRAM EN 55022 Warning This is a Class A product. In a domestic environment it may cause radio interfer- ence, in which case the user may be required to take adequate measures.

Manufacturer: InFocus Corporation 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USA European Office: Olympia 1, NL-1213 NS Hilversum, The Netherlands We declare under our sole responsibility that the LP130 projector conforms to the following directives and norms: Directive 89/336/EEC, Amended by 93/68/EEC EMC: EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 Directive 73/23/EEC, Amended by 93/68/EEC Safety: EN 60950: 1992 + A1 + A2 + A3 + A4: 1997 February, 2001 Australian Certification C-tick mark Trademarks Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Digital Light Pro- cessing is a trademark or registered trademark of Texas Instruments. InFocus and LP are trademarks or registered trademarks of InFocus Corporation.

Safety Instructions iii Introduction 1 Image Resolution 1 Compatibility 1 Unpacking the Projector 1 Usage Guidelines 3 If You Need Assistance 4 Warranty 4 Setting up the Projector 5 Connecting a Computer 7 Connecting a Video Player 8 Powering up the Projector and Adjusting the Image 9 Turning Off the Projector 9 Using the Projector 11 Basic Image Adjustment 11 Adjusting the Projector 11 Using the Remote Control 13 Using the Keypad and Remote Buttons 14 Using the On-Screen Menus 16 Display Menu 17 Image Menu for Computer Sources 19 Image Menu for Video Sources 21 Control Menu 22 Advanced Menu 23 Language Menu 24 Status Menu 25 Maintenance & Troubleshooting 27 Cleaning the Lens 27 Replacing the Projection Lamp 27 Replacing the Batteries in the Remote Control 31 Using the Security Lock 31 Troubleshooting 32

40 Using Video Mirroring with a PowerBook Computer 45 Projected Image Size 46 Index 47

using your new projector. Failure to comply with safety instruc- tions may result in fire, electrical shock, or personal injury and may damage or impair protection provided by equipment. Please save all safety instructions. Safety Definitions: • Warning: Statements identify conditions or practices that could result in personal injury. • Caution: Statements identify conditions or practices that could result in damage to your equipment. Safety Symbols: Attention: For information about usage of a feature, please refer to the User’s Guide. Warning: Hot surface. Do not touch. An arrow pointing to the lamp door on the projector. Safety Terms: • Warning: Don’t look directly into the lens when the projector is turned on. •Warning: To replace the lamp, turn the projector off and unplug the power cord. To avoid burns, wait 30 min- utes before opening the lamp access grill. Follow all instruc- tions provided in this User’s Guide. •Warning: Please use the power cord provided. • Warning: Refer all service to qualified service personnel. Ser- vicing your own projector will void the warranty. See the fol- lowing page for the customer service contact information. • Caution: Don’t block ventilation openings.

damage your projector. • Caution: Don’t place the projector on a hot surface or in direct sunlight. • Caution: Do not drop the projector. Transport the projector in an InFocus-approved case; see page 39 for a list of cases. Important Operating Considerations Do not place the projector on a tablecloth or other soft covering that may block the vents. In the unlikely event of the bulb ruptur- ing, thoroughly clean the area in front of the projector and dis- card any edible items placed in that area. Customer Service If you need assistance, call InFocus Customer Service directly at 1-800-799-9911. Support is free between 6 a.m. and 6 p.m. PST, Monday through Friday. Support is available in North America after hours and weekends for a fee at 1-888-592-6800. Or, send us an e-mail at [email protected]. In Europe, call InFocus in The Netherlands at (31) 35-6474010. In Asia, call InFocus in Singapore at (65) 353-9424. Do not place objects in this area in front of the projector 2 ft (.6m)

for the mobile presenter. It generates crisp, clear images using Digital Light Processing™ (DLP) technology, and features an M1-DA type DVI connector for easy, built-in digital/analog and USB connectivity. It is easy to connect, easy to use, easy to trans- port, and easy to maintain. Image Resolution NOTE: The LP130 automatically expands 640x480 and 800x600 images to 1024x768. You can dis- play these images at their native resolutions using the Resize option in the Image menu. See page 19 for more information. The XGA resolution of the LP130’s projected image is 1024x768. The projector is compatible with screen resolutions up to 1280x1024. If your computer’s screen resolution is higher than 1280x1024, reset it to a lower resolution before you connect the projector. Compatibility The projector is compatible with a wide variety of computers and video devices, including: • IBM-compatible computers, including laptops, up to 1280x1024 resolution. • Apple® Macintosh® and PowerBook® computers up to 1280x1024 resolution. NOTE: The projector is compati- ble with 1080i and 720P HDTV formats. • Most standard VCRs, DVD players, HDTV sources, camcord- ers and laser disc players. Unpacking the Projector The projector comes with the items shown in Figure 1. Check to make sure all are included. Contact your InFocus dealer imme- diately if anything is missing. If you are experienced in setting up presentation systems, use the Quick Start card that was included in the shipping box. For com- plete details on connecting and operating the projector, refer to this User’s Guide. Electronic versions of this user’s guide in mul- tiple languages are available on the included CD and on our web- site at www.infocus.com.

product updates, announcements, and special offers from InFocus. Or, register online at www.infocus.com/service/register and you will be automatically entered to win free merchandise. FIGURE 1 Shipping box contents 1. LP130 digital projector + lens cap 5. Remote control 2. Soft carry case 6. Analog computer cable 3. User’s Guide, Quick Start card, and CD 7. Composite video cable 4. Power cord 8. S-video cable data video keystone forward backward menu/select 1 2 3 4 5 6 7 8

Usage Guidelines • Do not look directly into the projection lens when the projector is turned on. The bright light may harm your eyes. • Do not block the grills on the projector. Restricting the air flow can cause it to overheat and turn off. If this happens, you must wait a minute before attempting to turn it back on. • Handle the projector as you would any product with glass components. Be especially careful not to drop it. • Avoid leaving the projector in direct sunlight or extreme cold for extended periods of time. If this happens, allow it to reach room temperature before use. • Transport the projector in a vendor-approved hard or soft case. Part numbers for these cases are listed on page 39. security lock power cord connector power switch keypad zoom ring focus ring computer and video connectors

The first place to look for help is in this manual. Be sure to check the guidelines in “Troubleshooting” on page 32. Or, check the Service and Support section of our website at http://www.infocus.com/service. You’ll find a Technical Library, FAQs, and support contacts including a technical support e-mail form. If those sources don’t answer your question, call your InFocus dealer. You can also call InFocus Customer Service directly at 1-800-799-9911. Call between 6 a.m. and 6 p.m. PST, Monday through Friday. Service is available in North America after hours and on weekends for a fee at 1-888-592-6800. In Europe, call InFocus in The Netherlands at (31) 35-6474010. In Asia, call InFocus in Singapore at (65) 353-9424. Or, send us an e-mail at [email protected] Our World Wide Web address is http://www.infocus.com. Warranty This product is backed by a limited two-year warranty. The details of the warranty are printed at the back of this manual. Included with the standard warranty is Priority Care* for one full year and 90 days of free 7x24 Technical Support (after 90 days there will be a minimal $35/incident fee). An extended warranty plan may be purchased from your InFocus dealer, any time dur- ing the original two year warranty period. Refer to page 39 for the part number. When sending your projector in for repair, InFocus recommends shipping the unit in its original packing material, or having a pro- fessional packaging company pack the unit for shipping. Do not ship your projector in the enclosed soft case. Please insure your shipment for its full value. * Priority Care is currently available in the U.S., Canada, EU coun- tries, Switzerland and Norway.

1 Place the projector on a flat surface. • The projector must be within 10 feet (3 m) of your power source and within 6 feet (1.8 m) of your computer. • If you want to project from behind a translucent screen, set up the projector behind your screen. See “Rear Projection” on page 23 to reverse the image. 2 Position the projector the desired distance from the screen. • If the image is too big or too small, use the zoom ring to adjust the size or move the projector forward or backward. Figure 3 shows three projected image sizes. For more infor- mation about image size, see “Projected Image Size” on page 46. FIGURE 3 Projected image size at minimum zoom 3 Make sure the projector and the computer are turned off. 3.0 ft. 11.8 ft. 7.1 ft. 5 ft. 12 ft. 20 ft.

make sure the projector and all other equipment is turned off. If you’re connecting a computer, make sure the distance between it and the projector is 6 feet or less. FIGURE 4 Connector panel FIGURE 5 Computer cable NOTE: If you are connecting an older Macintosh computer that does not have a 15-pin connector, you must use a Mac adaptor between the computer and the projector. See “Optional Accessories” on page 39. video power switch computer power cord to computer video to projector to computer to USB mouse

The projector ships with an analog computer cable. If your com- puter has a digital output, you can order the optional digital com- puter cable. Using a digital source generates the highest quality and brightest image possible. See “Optional Accessories” on page 39. 1 Plug the end of the computer cable with one cable into the connector on the projector. NOTE: Many laptop computers do not automatically turn on their external video port when a sec- ondary display device such as a projector is connected. Refer to your computer manual for the command that activates the exter- nal video port. Activation com- mands for some laptop computers are listed in the Appendix of this manual on page 40 and in the Service section of our website. 2 Plug the blue end of the computer cable into the video connec- tor on your computer. 3 If you want to advance slides in a PowerPoint™ presentation using the remote, plug the USB cable into the USB mouse con- nector on your computer. FIGURE 6 Connecting the projector to a computer NOTE: The USB mouse is sup- ported for use with Windows 98, Windows 2000, and Apple OS 8.5 and higher only. Now you’re ready to power up the projector and your laptop. Skip to “Powering up the Projector and Adjusting the Image” on page 9. NOTE: You do not need to restart your computer after connecting a USB mouse to use it computer cable USB mouse

If your video player uses a round, one-prong composite video connector, use the composite video cable. If your video player uses a round, four-prong S-video connector, use the S-video cable. S-video generates a higher quality image. NOTE: HDTV sources must be connected to the projector using the computer cable (not the video cable). See the previous pages for details on connecting this cable. 1 Plug the composite video cable’s round yellow connector into the “video-out” connector on your video player (Figure 7). This connector may be labeled “To Monitor.” • If you’re using an S-video cable, connect the round black connector to the “S-video out” connector on the video player. 2 Plug the square yellow connector into the video connector on the projector. FIGURE 7 Connecting the projector to a video player CAUTION: Your video player may also have a “Video Out” connector for a coaxial cable connection. DO NOT use this to connect to the projector. The projector is compatible with these major broadcast video standards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, PAL-60, and SECAM. It automatically adjusts to optimize its performance for the incoming video. video cable

NOTE: Always use the power cord that shipped with the projector. 1 Remove the lens cap. 2 Plug the power cord into the back of the projector, then plug it into your electrical outlet. A surge-protected power strip is recommended. 3 Press the Power switch on the back of the projector. NOTE: The first time you connect your computer to the projector, the computer may display a message stating that new hardware was found. The Add New Hardware Wizard may appear. Use the Wiz- ard to load the correct driver (the computer considers the projector a Plug and Play Monitor). • The fans start to run, the LED on the top of the projector (Figure 11 on page 14) lights green, and the InFocus startup screen appears. It takes about one minute for the image to achieve full brightness. 4 If you connected a video player, turn it on. • The video image should display on the projection screen. If it doesn’t, press the source button on the keypad (page 14) or the video button on the remote to display your video image. 5 Turn on your computer. • The computer image should display on the projection screen. If it doesn’t, press the source button on the keypad or the data button on the remote to display your computer’s image. NOTE: With some computers, the order in which you power up the equipment is very important. Most computers should be turned on last, after all other peripherals have been turned on. Refer to your computer’s documentation to determine the correct order. • Make sure your laptop’s external video port is activated; see “Portable and Laptop Activation Chart” on page 40 for details. • If necessary, make adjustments to the image using the pro- jector’s on-screen menus. To open the menus, press the menu/select button on the keypad or remote. For more information about the menus, see page 16. Turning Off the Projector To turn off the projector, press the Power switch. If you want to turn the lamp back on, you must allow 90 seconds for the lamp to cool. The lamp won’t light if it’s too hot. NOTE: To maximize lamp life, allow the projector to run for at least five minutes before turning it off.

This section describes how to use and make adjustments to the projector. It also provides a reference to the keypad and remote buttons and the options available from the on-screen menus. Basic Image Adjustment 1 Make sure you have powered up your equipment in the right order (page 9). 2 If the image doesn’t display completely, zoom the image (page 11), adjust the height of the projector (page 12) or center the image by adjusting its horizontal or vertical position (page 20). Be sure the projector is at a 90 degree angle to the screen. 3 If the image is out of focus, rotate the focus lens (page 11). 4 If the colors don’t look right, adjust the brightness, contrast, tint, or color (page 17). Adjusting the Projector To focus the image, rotate the focus ring (Figure 8) until the image is clear. To zoom the image, rotate the zoom ring. This adjusts the image size. NOTE: To obtain the best overall focus quality, open the menu and focus on the text. This will ensure that the best overall image quality is achieved. FIGURE 8 Focus ring and zoom ring focus ring zoom ring

tor foot and button. To raise the projector: 1 Press and hold the elevator button (Figure 9). 2 Raise the projector to the height you want, then release the button to lock the elevator foot into position. FIGURE 9 Adjusting the height of the projector elevator button elevator foot (under finger)

To use the forward and back buttons on the remote to advance slides in PowerPoint, you must connect the USB mouse connector on the computer cable to the computer. See page 7 for details. Point the remote control at the projection screen or at the front of the projector (not at the computer). The range for optimum oper- ation is about 25 feet. If you point the remote at the projection screen, the distance to the screen and back to the projector must be less than or equal to 25 feet. For best results, point the remote directly at the projector. FIGURE 10 Remote control data video keystone forward back menu/select

While the menus are displayed, the source and reset buttons on the keypad and the up and down arrow buttons on the remote act as menu navigation and adjustment buttons and the menu/select button acts as a select button. See “Using the On- Screen Menus” on page 16 for details. FIGURE 11 Keypad and remote buttons Menu/select NOTE: If you have turned Auto Source off (page 22), you may need to press the source button more than once to display an active source. The sources switch in this order: data analog, data digital, S-video, and composite video. Press the menu/select button to open the on-screen menus. Press menu/select again (while Exit is highlighted) to close the menus. (The menus automatically close after 30 seconds if no buttons are pressed.) When you close the menus, the projector saves any changes you made. For more information about the on-screen menus, see page 16. Source (keypad only) or Data and Video (remote only) When you have more than one source (computer and video) con- nected to the projector, select between them by pressing the source button on the keypad or the data or video button on the remote. menu/select source reset LED data video keystone forward backward menu/select

dard, and Rear Projection) to their original settings. Keystone + - (remote only) Use this feature to adjust the image vertically and make a squarer image. 1 Press the keystone + button to reduce the upper part of the image, and press the keystone - button to reduce the lower part. You can also adjust keystone from the Display menu (see page 17 for details on the menu). FIGURE 12 Adjusting the keystone Forward/back buttons (remote only) These buttons act like the page up and page down buttons on your computer’s keyboard. You can use them to advance through a slide show in PowerPoint™ presentations. To use this feature, you must connect the USB mouse connector on the computer cable to your computer. See page 7 for details. Up/down arrow buttons Use these buttons to navigate through and make adjustments to the on-screen menus. See “Using the On-Screen Menus” on page 16 for details. increasing keystone decreasing keystone

The projector has menus that allow you to make image adjust- ments and change a variety of settings. These adjustments aren’t available directly from the keypad. NOTE: Some menu items may be grayed out (dimmed) at certain times. This indicates the item is not applicable to your setup or the item is not enabled until another selection is made. To open the on-screen menus, press the menu/select button on the keypad or remote. (The menus automatically close after 30 seconds if no buttons are pressed.) This displays the Main menu and changes the source and reset buttons on the keypad to menu navigation buttons. Press the button to move the cursor down and press the button to move the cursor up. The selected menu is highlighted. FIGURE 13 Main menu To change a menu setting, use the up and down arrow buttons to move the cursor up and down to the item you want to change (the selected item is highlighted), then press menu/select. When an item is selected, its button appears depressed to provide a visual indication of selection. Use the up and down arrows to adjust the setting or turn it on and off. Press menu/select when you are done. Press the up and down arrows to move to another setting. When you have completed your adjustments, navigate to Exit, then press menu/select. You are returned to the top of the Main menu. Press menu/select again to exit the Main menu, or navigate to another submenu.

to display the Main menu, press the down arrow to highlight Dis- play, then press menu/select again to access the Display menu. FIGURE 14 Display menu Keystone This option helps to keep the image square as the angle of projec- tion is changed. Use this feature to adjust the image vertically and make a squarer image. See page 15 for details on keystone adjustments. 1 Press the down button to highlight Keystone, then press menu/select. Use the up and down arrows to adjust the key- stone setting. Press menu/select to accept your changes. Brightness Adjusting the brightness changes the intensity of the image. 1 Use the up and down arrows to highlight Brightness, press menu/select, use the arrows to adjust the brightness, then press menu/select to accept your changes.

and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. 1 Use the up and down arrows to highlight Contrast, press menu/select, use the arrows to adjust the contrast, then press menu/select to accept your changes. Tint NOTE: The color setting applies to video sources only. The tint setting applies to NTSC video sources only. The tint adjusts the red-green color balance in the projected image. 1 Use the up and down arrows to highlight Tint, press menu/select, use the arrows to adjust the tint, then press menu/select to accept your changes. Color The color setting adjusts a video image from black and white to fully saturated color. 1 Use the up and down arrows to highlight Color, press menu/select, use the arrows to adjust the color, then press menu/select to accept your changes. Blank screen Blank Screen determines what color is displayed when there is no active source and when the projector is in standby. 1 Use the up and down arrows to highlight Blank screen, press menu/select, use the arrows to cycle through the options blue, black, and white, then press menu/select to accept your selec- tion.

To access the Image menu settings, press the menu/select button to display the Main menu, press the down arrow to highlight Image, then press menu/select again to access the Image menu. FIGURE 15 Image menu for computer sources Resize Resize allows you to select from among four different re-sizing options. The default is Standard, which resizes the image from its original version to fit a standard 4x3 aspect ratio screen. Wide- screen Letterbox preserves the 16x9 aspect ratio of the original theater version, but the image is placed in a 4x3 space, so black bars appear at the top and bottom of the image. Enhanced Wide- screen also preserves the aspect ratio of the original theater ver- sion and is designed to be used with content that is Enhanced for Widescreen TVs. This option yields more detail than Widescreen Letterbox. Native reduces the Standard size to match the height of Enhanced Widescreen. Highlight Resize, press menu/select, use the up or down arrow buttons to cycle through the options, then press menu/select to select. Auto Image The projector automatically adjusts tracking, signal synchroniza- tion and vertical and horizontal position for most computers. If you want to adjust these features manually, you must turn off Auto image first. Highlight Auto image, press menu/select, then press the up or down arrow buttons to turn this feature off and on.

most computers. But if the projected computer image looks fuzzy or streaked, try turning Auto image off then back on again. If the image still looks bad, try adjusting the signal synchronization manually: 1 Turn Auto Image off. 2 Highlight Manual sync, press menu/select, use the arrow but- tons to adjust Manual sync until the image is sharp and free of streaks, then press menu/select. Manual Tracking The projector adjusts tracking automatically to match the video signal from your computer. However, if the display shows evenly spaced, fuzzy, vertical lines or if the projected image is too wide or too narrow for the screen, try turning Auto Image off then back on again. If the image is still bad, try adjusting the tracking man- ually: NOTE: The Manual Sync, Manual Tracking, Horizontal Position and Vertical Position options are available only for analog computer sources. The projector sets these options automatically for digital computer and video sources, with no manual override. 1 Turn Auto image off. 2 Highlight Manual tracking, press menu/select, use the arrow buttons to adjust Manual tracking until the fuzzy vertical bars are gone, then press menu/select. Horizontal Position Follow these steps to manually adjust the horizontal position: 1 Turn Auto image off. 2 Highlight Horizontal position, press menu/select, use the arrow buttons to adjust the Horizontal position, then press menu/select. Positioning adjustments are saved when you turn off the projec- tor. Vertical Position Follow these steps to manually adjust the vertical position. 1 Turn Auto image off. 2 Highlight Vertical position, press menu/select, use the arrow buttons to adjust the Vertical position, then press menu/select. Positioning adjustments are saved when you turn off the projec- tor.

FIGURE 16 Image menu for video sources Resize Resize allows you to select from among four different re-sizing options. The default is Standard, which resizes the image from its original version to fit a standard 4x3 aspect ratio screen. Wide- screen Letterbox preserves the 16x9 aspect ratio of the original theater version, but the image is placed in a 4x3 space, so black bars appear at the top and bottom of the image. Enhanced Wide- screen also preserves the aspect ratio of the original theater ver- sion and is designed to be used with content that is Enhanced for Widescreen TVs. This option yields more detail than Widescreen Letterbox. Native reduces the Standard size to match the height of Enhanced Widescreen. Highlight Resize, press menu/select, use the up or down arrows to cycle through the options, then press menu/select. Video Standard (video sources only) When Video is set to Auto, the projector attempts to pick the video standard (NTSC, NTSC 4.43, PAL, or SECAM) automati- cally based on the input signal it receives. (The video standard options may vary depending on your region of the world.) If the projector is unable to detect the correct standard, the colors might not look right or the image might appear “torn.” If this happens, manually select a video standard. Highlight Video standard, press menu/select, use the up or down arrows to cycle through the options, then press menu/select to select.

to display the Main menu, press the down arrow to highlight Control, then press menu/select again to access the Control menu. FIGURE 17 Control menu Auto Source When this feature is On, the projector automatically finds the active source, checking the default source first. When this feature is Off, the projector defaults to the source selected in Default Source. To display another source, you must manually select one by pressing the source button on the keypad or the data or video button on the remote. Highlight Auto source, press menu/select, then press the up or down arrow buttons to turn this feature off and on. Default Source This determines which source the projector checks first for active video during power-up. Select among Data-Analog, Data-Digital, composite video, and S-Video. Highlight Default source, press menu/select, use the up or down arrows to cycle through the options, then press menu/select to select.

ton to display the Main menu, press the down arrow to highlight Advanced, then press menu/select again to access the Advanced menu. FIGURE 18 Advanced menu Rear Projection When you turn Rear Projection on, the projector reverses the image so you can project from behind a translucent screen. Highlight Rear Projection, press menu/select, then press the up or down arrow buttons to turn this feature off and on. Reset Highlight Reset then press menu/select to reset the options in the menus (except Language, Video Standard, and Rear Projection) to their original settings.

Spanish, Chinese or Japanese. 1 Press the menu/select button to display the Main menu, press the arrow buttons to highlight Language, then press menu/select again to access the Language menu. 2 Press the arrow buttons to highlight the desired language, then press menu/select. Press menu/select to exit this menu and return to the Main menu.

the Status menu, highlight Status from the Main menu, then press menu/select. FIGURE 20 Status menu Lamp hours used Indicates how many hours the current lamp has been in use. The counter starts at zero hours and counts each hour the lamp is in use. Replace the bulb when the brightness is no longer accept- able. See “Replacing the Projection Lamp” on page 27 for details. Computer resolution Shows your computer’s resolution setting. To change this, go to your computer’s Control Panel and adjust the resolution in the Display tab. See your computer’s user’s guide for details. Source Indicates the active source, Data-Analog, Data-Digital, Compos- ite video, or S-video. Version Indicates the projector’s software version. This information is useful when contacting Technical Support.

This section describes how to: •clean the lens •replace the projection lamp •replace the batteries in the remote •use the security lock feature •troubleshoot the projector Cleaning the Lens Follow these steps to clean the projection lens: 1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth. • Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. • Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. 2 Lightly wipe the cleaning cloth over the lens in a circular motion. 3 If you don’t intend to use the projector immediately, replace the lens cap. Replacing the Projection Lamp WARNING: To avoid burns, allow the projector to cool for at least 30 minutes before you open the lamp access grill. Never extract the lamp module while the projector is operating. The lamp hour counter in the Status menu counts the number of hours the lamp has been in use. Change the lamp when the brightness is no longer acceptable. You can order new lamp mod- ules from your InFocus dealer. See “Accessories” on page 38 for information. Follow these steps to replace the projection lamp: 1 Turn off the projector and unplug the power cord. 2 Wait 30 minutes to allow the projector to cool thoroughly.

the front of the projector. Slide the screwdriver toward the back of the projector to disengage the lamp access grill, then slide the lamp access grill off (away from the lens). WARNING: Be extremely careful when removing the lamp module. In the unlikely event that the bulb ruptures, small glass fragments may be generated. The lamp module is designed to contain these fragments, but use caution when removing the lamp module. FIGURE 21 Disengaging and removing the lamp access grill CAUTION: Never operate the projector with the lamp access grill removed. This disrupts the air flow and causes the projector to overheat. 4 Pull the yellow tab on the lamp module. FIGURE 22 Pulling the tab on the lamp module tab

FIGURE 23 Loosening the screw on the lamp module 6 Grasp the pull tab to pull the lamp module out. Dispose of the lamp module in an environmentally proper manner. WARNING: Do not drop the lamp module or touch the glass bulb! The glass may shatter and cause injury. FIGURE 24 Removing the lamp module

8 Tighten the screw on the outside of the module. 9 Press the yellow tab to reconnect the lamp module. 10 Replace the lamp access grill by lining up the ribs on the grill with the marks on the bottom case and sliding the grill in the direction of the arrows on the bottom case. 11 Plug in the power cord and press the Power switch to turn the projector back on. 12 To reset the lamp hour counter in the Status menu, press and hold the reset button, then press the menu/select button (while still holding down the reset button) for 10 seconds. Verify that the counter was reset by pressing the menu/select button and viewing the counter in the Status menu. See page 25 for details on the Status menu.

The life of the batteries depends on how often and how long you use the remote. Symptoms of low battery charge include erratic responses when using the remote and a reduced range of opera- tion. Follow these steps to replace the batteries: 1 Turn the remote face down in your hand. 2 Push the tab on the battery door toward the top of the remote and lift the door off. 3 Remove the old batteries and dispose of them in an environ- mentally proper manner. 4 Install two new AAA alkaline batteries. Make sure you install each in the correct direction. 5 Insert the hooks on the battery door into the remote and press the tab to re-install the door. Using the Security Lock NOTE: The lamp cannot be removed while the security lock is attached. The projector has a security connector for use with a PC Guardian Cable Lock System (Figure 25). See “Optional Accessories” on page 39 for ordering information. Refer to the information that came with the lock for instructions on how to use it to secure the projector. FIGURE 25 Installing the security lock

•Make sure that the power cord is properly connected to a fully functional AC electrical outlet. Make sure that the power cord is also properly connected to the projector. •If the projector is plugged into a power strip, make sure the power strip is turned on. •Make sure the projector is turned on. Problem: Projector is running, but nothing appears on projec- tion screen •Make sure you have removed the lens cap on the projection lens at the front of the projector. •Check the projector’s lamp to ensure that it is securely con- nected in the lamp module. Make sure the lamp access grill is installed. See “Replacing the Projection Lamp” on page 27. Problem: Only the start-up screen displays •Verify that the cables are connected correctly. See page 7 for connection procedures. •Make sure that the cables do not have any bent pins. •Verify that the proper input source is connected. See “Source (keypad only) or Data and Video (remote only)” on page 14. •You might need to turn everything off and power up the equipment again in the proper order. Refer to your com- puter’s documentation to determine the correct order. •Make sure your laptop’s external video port is turned on. See the “Portable and Laptop Activation Chart” on page 40 or your computer’s manual for details. •Make sure your computer’s video board is installed and con- figured correctly. •Make sure your computer has a compatible video board. The projector isn’t CGA or EGA compatible.

1 Open “My Computer” icon, the Control Panel folder and then the Display icon. 2 Click the Settings tab. 3 Verify that the Desktop area is set to 1280x1024 or less. Problem: Color or text not being projected •You might need to adjust the brightness up or down until the text is visible. Refer to “Brightness” on page 17 for more infor- mation. Problem: The screen resolution is not right •Make sure the computer’s video card is set for a resolution of no greater than 1280x1024. Problem: Image isn’t centered on the screen •Move the projector to reposition the image. •Reposition the image using the menu. Refer to “Horizontal Position” on page 20 and “Vertical Position” on page 20. •Be sure the projector is at a 90 degree angle to the screen. Problem: Image is too wide or narrow for screen •Adjust the zoom or projector placement. •Adjust the resolution of your video card if it’s greater than 1280x1024. Problem: Image is out of focus •Turn the projection lens to focus the image. •Make sure the projection screen is at least 5 feet (1.5 m) from the projector. •Check the projection lens to see if it needs cleaning. Problem: Image and menus are reversed left to right •Rear projection mode is probably turned on. Turn Rear Projec- tion off in the Controls menu. The image should immediately return to forward projection. See “Rear Projection” on page 23.

spots •Adjust the brightness. See “Brightness” on page 17. •Check the projection lens to see if it needs cleaning. Problem: Image is “noisy” or streaked Try these steps in this order. 1 Deactivate the screen saver on your computer. 2 Turn Auto Image off and then back on again. See “Auto Image” on page 19. 3 Turn Auto Image off and adjust the synchronization and track- ing manually to find an optimal setting. See “Manual Sync” on page 20 and “Manual Tracking” on page 20. •The problem could be with your computer’s video card. If possible, connect a different computer. Problem: Projected colors don’t match the computer or video player’s colors •Just as there are differences in the displays of different moni- tors, there are often differences between the computer image and the projected image. Adjust the brightness, tint and/or contrast from the Display menu. See “Brightness” on page 17, “Tint” on page 18 and “Contrast” on page 18. Problem: Lamp seems to be getting dimmer •The lamp begins to lose brightness when it has been in use for a long time. Replace the lamp as described in “Replacing the Projection Lamp” on page 27. Problem: Lamp shuts off •A minor power surge may cause the lamp to shut off. Unplug the projector, wait at least a minute, then plug it back in. •Make sure the vents are not blocked.

the Service and Support section of our website at http://www.infocus.com/service. You’ll also find a Technical Library, FAQs, and support contacts including a technical sup- port e-mail form. Before calling your dealer or InFocus Technical Support for assis- tance, please have the following information available: •the projector’s serial number (located on the bottom label) •the resolution of your computer. Call InFocus Technical Support at 1-800-799-9911 between 6 a.m. and 6 p.m. PST, Monday through Friday. Service is available in North America after hours and on weekends for a fee at 1-888-592-6800. In Europe, call InFocus in The Netherlands at (31) 35-6474010 between 8 a.m. and 6 p.m. Central European Time. In Asia, call (65) 353-9424 between 9:30 a.m. and 5:30 p.m. Or, send us an e-mail at [email protected]

ture and humidity ranges specified. Temperature Operating 50 to 104° F (10 to 40° C) at sea level 50 to 95° F (10 to 35° C) at 10,000 feet Non-operating -4 to 158° F (-20 to 70° C) Altitude Operating 0 to 10,000 feet (3,048 meters) Non-operating 0 to 20,000 feet (6,096 meters) Humidity Operating and non-oper. 10% to 95% relative humidity, non-condensing Dimensions 6.25 x 8.25 x 2 inches (15.9 x 21.0 x 5.1 cm) Weight 2.9 lbs. (1.33 kg) unpacked Optics Focus Range 4.9 - 13 feet (1.5-4 m) Lamp Type 120-watt UHP lamp Input Power Requirements 100-120VAC 2A;50/60Hz 200-240VAC 1A; 50Hz

approved accessories. Other products have not been tested with the projector. Power Cords (one ships with projector, type depends on country) Standard Accessories (ship with the projector) Part Number Quick Start card 009-0526-xx User’s Guide 010-0251-xx Soft Case 110-0342-xx Shipping Box 110-0343-xx Analog Computer Cable 6 ft (1.8 m) 210-0185-xx Composite RCA Video Cable 6 ft (1.8 m) 210-0192-xx S-video Cable 6 ft (1.8 m) 210-0193-xx Remote 590-0379-xx Projection Lamp Module (included in projector) SP-LAMP-LP1 Lens Cap 505-0713-xx Online User’s Guide CD-ROM 010-0274-xx North American Power Cord 210-0109-xx Australian Power Cord 210-0111-xx UK Power Cord 210-0110-xx European Power Cord 210-0112-xx Japanese Power Cord 210-0204-xx

items by contacting your dealer or InFocus Catalog Sales at 1-800-660-0024. Optional Accessories Deluxe Travel Case CA-WHL340 Executive Leather Case CA-EXE-340 Hard Travel Elite Porter Case CA-HD-PORTERELT Projection Lamp Module SP-LAMP-LP1 Digital Computer Cable SP-DVI-D Digital/Analog Interface Card SP-DVI-CARD USB Ranger 400 System HW-USBRNGR4 HW-USBRNGR4-I Macintosh Adaptor SP-MACADPT Executive Plus Remote HW-EXPLUS Full-Feature LaserPro Remote Control HW-LASERPRO GyroMouse Pro RF Remote (US, Mexico, Canada, UK only) HW-RF-GPRO Executive Remote IR Receiver HW-EXRCVR Remote Point RF Remote with LaserPointer (US and Canada only) HW-RF-REMLSR GyroMouse Presenter RF Remote Control (US, Mexico, Canada, UK only) HW-RF-GPRES PC Guardian Projector Cable Lock SP-LOCK 40” Portable Projection Screen HW-PORTSCR40 50” Portable Projection Screen HW-PORTSCR50 60” Deluxe Insta-Theatre Screen HW-DLXSCRN Portable Projector Stand SP-STND eBeam (Web Enabled Electronic Meeting Assistant) HW-EBEAM 3rd Year Advantage Service Plan (1 year extension) EW-LP13xx-12

NOTE: Visit our website at www.infocus.com for the most current activation chart. It is located in the Technical Library in the Service and Support section. Many laptop computers do not automatically turn on their exter- nal video port when a projector is connected. Activation com- mands for some laptop computers are listed in the following table. (If your computer is not listed or the given command does not work, refer to the computer’s documentation for the appro- priate command.) On many laptops, the activation function key is labeled with an icon, for example or the text CRT/LCD. NOTE: Usually, pressing the key commands once activates the external video port, pressing it again activates both the external and internal ports, and pressing it a third time activates the internal port. Refer to your computer’s documentation for details on your specific model. Computer Key command to activate port Key command to de-activate port Acer Ctrl-Alt-Esc (for setup) Ctrl-Alt-Esc (for setup) AST* ** FN-D or Ctrl-D FN-D or Ctrl-D Ctrl-FN-D Ctrl-FN-D FN-F5 FN-F5 type from A:/IVGA/CRT type from A:/IVGA/CRT FN-F12 FN-F12 AMS FN-F2 FN-F2 AMT setup screen setup screen AT&T FN-F3 FN-F6 FN-F3 FN-F6 Advanced Logic Research Ctrl-Alt-V Ctrl-Alt-V Altima Shift-Ctrl-Alt-C Shift-Ctrl-Alt-L setup VGA/ Conf.Simulscan setup VGA/ Conf.Simulscan Ambra** FN-F12 FN-F12 FN-F5 FN-F5 F2/Choose Option/F5 F2/Choose Option/F5 Amrel* ** setup menu setup menu Shift-Ctrl-D Shift-Ctrl-D Apple see Mac Portable and Mac PowerBook Aspen automatic automatic Award FN-F6 FN-F6 BCC* automatic reboot computer

bootup reboot for LCD or CRT options to appear Chaplet** setup screen setup screen FN-F6 FN-F6 FN-F4 FN-F4 Chembook FN-F6 FN-F6 Commax Ctrl-Alt-#6 Ctrl-Alt-#5 Compaq* ** Ctrl-Alt-< Ctrl-Alt-> FN-F4 FN-F4 automatic automatic mode/? (for setup option) mode/? (for setup option) Compuadd* ** automatic automatic Alt-F for screen setup option Alt-F for screen setup option Data General Ctrl-Alt-Command Ctrl-Alt-Command Data General Walkabout 2 CRT/X at DOS prompt reboot Datavue Ctrl-Shift-M Ctrl-Shift-M DEC** FN-F5 FN-F5 FN-F4 FN-F4 Dell** Ctrl-Alt-< Ctrl-Alt-> Ctrl-Alt-F10 Ctrl-Alt-F10 FN-F8 (CRT/LCD) FN-F8 FN-D FN-D FN-F12 FN-F12 Digital* automatic reboot FN-F2 FN-F2 Dolch dip switch to CRT dip switch to LCD Epson dip switch to CRT dip switch to LCD Everex* setup screen option setup screen option For-A Ctrl-Alt-Shift-C Ctrl-Shift-Alt-L Fujitsu FN-F10 Computer Key command to activate port Key command to de-activate port

taneous FN-F3 FN-F1 Grid* ** FN-F2, choose auto or simultaneous FN-F2 Ctrl-Alt-Tab Ctrl-Alt-Tab Hitachi FN-F7 FN-F7 Honeywell FN-F10 FN-F10 Hyundai setup screen option setup screen option IBM 970* automatic warm reboot IBM ThinkPad** reboot, enter setup menu FN-F2 FN-F7, select choice from setup menu FN-F1, select choice FN-F5, select choice PS/2 SC select choice (CRT, LCD, etc.) Infotel FN-F12 FN-F12 Kaypro boot up, monitor plugged in unplug monitor Kris Tech FN-F8 FN-F8 Leading Edge FN-T FN-T Mac Portable 100 no video port: not compatible Mac PowerBook 140, 145, 150, 170 no video port: requires a 3rd-party interface 160, 165, 180, 520, 540, 5300 Control Panel folder, Pow- erBook Display folder; Activate Video Mirroring warm reboot 210, 230, 250, 270, 280, 2300 requires Apple Docking Station or Mini Dock Magitronic FN-F4 FN-F4 Mastersport FN-F2 FN-F1 Computer Key command to activate port Key command to de-activate port

setup screen option NEC* ** setup screen option setup screen option CRT at the DOS prompt LCD at the DOS prompt FN-F3 FN-F3 Olivetti* automatic automatic FN-O/* FN-O/* Packard Bell* ** FN-F0 FN-F0 Ctrl-Alt-< Ctrl-Alt-> Panasonic FN-F2 FN-F2 Prostar Ctrl-Alt-S at bootup Ctrl-Alt-S at bootup Samsung* setup screen option setup screen option Sanyo setup screen option setup screen option Sharp dip switch to CRT dip switch to LCD Sun SPARC- Dataview Ctrl-Shift-M Ctrl-Shift-M Tandy** Ctrl-Alt-Insert Ctrl-Alt-Insert setup screen option setup screen option Tangent FN-F5 FN-F5 Texas Instru- ments* setup screen option setup screen option Top-Link* ** setup screen option setup screen option FN-F6 FN-F6 Toshiba* ** Ctrl-Alt-End Ctrl-Alt-Home FN-End FN-Home FN-F5 FN-F5 setup screen option setup screen option Twinhead* FN-F7 FN-F7 FN-F5 FN-F5 Automatic Automatic WinBook Ctrl-Alt-F10 Ctrl-Alt-F10 Computer Key command to activate port Key command to de-activate port

to the external CRT port when some type of display device is attached. ** These manufacturers offer more than one key command depend- ing on the computer model. Wyse software driven software driven Zenith** FN-F10 FN-F10 FN-F2 FN-F2 FN-F1 FN-F1 Zeos** Ctrl-Shift-D FN-F1 Ctrl-Shift-D FN-F1 Computer Key command to activate port Key command to de-activate port

When you turn video mirroring (called SimulScan in newer Pow- erBooks—see below) on, the projector displays the same informa- tion that appears on your PowerBook’s built-in screen. When video mirroring is off, the projector acts like a separate display. To turn on video mirroring for the first time: 1 Open the Monitors control panel; click on Monitor 2. 2 Set the number of colors you want. 3 Open the Control Strip, then click on the monitor icon. 4 Select “Turn Video Mirroring On.” Now you can turn video mirroring on and off from the Control Strip without having to open the Monitors control panel again. When using video mirroring and high color graphics such as slide shows, the projected image occasionally might turn black and white. If this happens, perform the following steps: 1 Turn off video mirroring. 2 Open the Monitors control panel. 3 Move the white menu bar to Monitor 2 to set the projector as the primary monitor. 4 Restart the PowerBook. Using SimulScan Some newer PowerBooks display images on an external monitor or projector differently than previous ones. When using SimulScan, the projector displays the same information that appears on your PowerBook To select SimulScan: 1 Open the Control Panel, then double-click Monitors and Sound. 2 In the Resolution list, choose the SimulScan mode, then click OK. 3 If this changes your display settings, a dialog box appears. Click OK to confirm the change.

NOTE: Use the graph and table to help you determine projected image sizes. FIGURE 26 Projected image size NOTE: Visit our website at www.infocus.com for an interactive image size calculator. It is located in the Technical Library in the Service and Support section. 50 100 150 200 250 5 10 0 15 20 25 30 Diagonal Image Size (inches) Distance to Screen (feet) maximum image size minimum image size Table 1: Range of distance to the screen for a given screen size Diagonal Screen Size (inches) Distance to screen Image Width (inches) Maximum distance (feet) Minimum Distance (feet) 60 48 8.5 6.9 72 58 10.2 8.3 84 67 11.9 9.7 90 72 12.7 10.4 100 80 14.1 11.6 120 96 17.0 13.9 150 120 21.2 17.4

activation commands for laptop com- puters 40 adjusting brightness 17 color 18 contrast 18 height of the projector 12 keystone 17 tint 18 Advanced menu options Rear projection 23 Reset 23 altitude limits 37 assistance. See Technical Support auto image 19 auto source 22 B brightness, adjusting 17 buttons on keypad Menu/select 14 Reset 15 Source 14 C cables computer cable 2, 6, 7 ordering 38 power 38 video 8 cases, ordering 38 centering the image 12, 20 cleaning the projection lens 27 color, adjusting 18 colors don’t match monitor colors 34 not displayed 33 compatibility IBM-compatible 1 Macintosh 1 computer cable 2, 6, 7 computers compatible 1 connecting 7 connecting computer 7 power cord 9 video player 8 contrast, adjusting 18 Control menu options Auto source 22 Default Source 22 D Default Source 22 Display menu options Blank screen 18 Brightness 17 Color 18 Contrast 18 Keystone 17 Tint 18 displaying on-screen menus 14

F focusing the image 11 forward/back buttons 15 fuzzy lines 20 H HDTV 1, 8, 18 height adjustment 12 I IBM-compatible computers compatibility 1 connecting 7 image adjusting 9, 11 centering 20 colors don’t match computer’s 34 focusing 11 fuzzy lines 20 has lines or spots 34 not centered 33 not displayed 32 out of focus 33 quality 33–34 resolution 1 reversed 23, 33 size 5, 46 streaked 34 too wide or too narrow 33 zooming 11 Image menu options Auto Image 19 Horiz. Position 20 Manual Sync 20 Manual Tracking 20 Resize 19 Vert. Position 20 Video Standard 21 K keypad 14 keystone adjustment 15 L lamp ordering 38, 39 replacing 27 turns off unexpectedly 34 lamp hour counter 25, 27, 30 Language menu 24 language, selecting for menus 24 laptop computers activation sequence to allow secondary display 40 compatibility 7 connecting 7 LED 9, 14 lens cap 38 cleaning 27 LP130 cases 38 project from behind the screen 23 setting up 5 specifications 37 turning off 9 turning on 9 M Macintosh computers compatibility 1 connecting 6 maintenance 27 menus. See on-screen menus monitor, projected colors don’t match 34

O on-screen menus changing language of 24 displaying 16 P PAL video 21 power cord connecting 9 ordering 38 power up sequence 9, 32 PowerPoint slides, advancing 15 project from behind the screen 23 R rear projection 23 remote control advancing PowerPoint slides with 15 replacing the batteries 31 using 13, 14 replacing projection lamp module 27 re-positioning the image on the screen 20 Reset button 15 resetting adjustments 15, 23 resetting the lamp hour counter 30 resizing the image 19 resolution 1 S safety guidelines iii security lock 31, 39 shutting off the projector 9 SimulScan, using with PowerBooks 45 Source button 14 specifications 37 starting up the projector 9 Status menu 25 S-video, connecting 8 T Technical Support in Europe 4 in Singapore 4 in USA 4 information to have on hand before you call 35 temperature limits 37 text not visible 33 tint, adjusting 18 troubleshooting 32 turning off the projector 9 turning on the projector 9 V vertical lines displayed 20, 34 video cable, connecting 8 video mirroring on a PowerBook 45 video resize 21 video standard 21 W warranty 39 widescreen video 19, 21 Z zooming the image 11

accordance with the written specifications of InFocus. Said limited warranty shall apply only to the first person or entity that purchases the Product for personal or business use and not for the purpose of distribution or resale. Said warranty shall continue for a period of two (2) years from the date of such purchase. The standard limited warranty excludes the lamps in projectors after 90 days and the accessories after one year. InFocus does not warrant that the Product will meet the specific requirements of the first person or entity that purchases the Product for personal or business use. InFocus’ liability for the breach of the foregoing limited warranty is limited to the repair or replacement of the Product or refund of the pur- chase price of the Product, at InFocus’ sole option. Under the Priority Care Program, Replacement Product will be brand new, if replaced during the first 90 days of ownership and may be re-furbished in “like-new” condition, at InFocus’ sole discretion, if replacement is required after 90 days of ownership. To exercise the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost and expense, to InFocus or to any authorized InFocus service center provided, and the Product must be accompanied by a written letter explaining the problem and which includes (i) proof of date of purchase; (ii) the dealer’s name; and (iii) the model and serial number of the Product. When sending your projector in for repair, InFocus recommends shipping the unit in its original packing material, or having a professional packaging company pack the unit for shipping. Do not ship your projector in the enclosed soft case. Please insure your shipment for its full value. A return authorization number, issued by the InFocus customer service department, must also be clearly displayed on the outside of the shipping carton containing the Product. Note: Remanufactured Products are exempt from the foregoing Limited Warranty. Please refer to the Remanufactured Product Warranty for applicable warranty information. WARRANTY LIMITATION AND EXCLUSION InFocus shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering, alterations, or service other than by InFocus or its authorized agents, causes other than from ordinary use or failure to properly use the Product in the application for which said Product is intended. DISCLAIMER OF UNSTATED WARRANTIES THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MER- CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO YOU.

IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN LIMITING INFOCUS’ LIABILITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE PRODUCT MAY BE BROUGHT BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPE- CIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. Part Number 010-0251-00