Encore ENHWI-N Operation & User’s Manual

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CE Mark Warning This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class B for ITE, the essential protection requirement of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or reproduced in any form without written consent from the company. Trademarks: All trade names and trademarks are the properties of their respective companies. Copyright © Encore Electronics, Inc. 2007, All Rights Reserved.

General Description····································································································· 1 Key Features ··············································································································· 2 The Front Panel··········································································································· 3 The Rear Panel ··········································································································· 4 Power Connection ································································································ 4 Restore Default Button ························································································· 4 Network configuration setup ························································································ 5 Computer configuration setup······················································································ 5 Wireless Router configuration setup············································································ 7 Network Setting ··········································································································· 9 WAN Interface Setup···························································································· 9 LAN Interface Setup ··························································································· 13 QoS Settings ······································································································ 15 Wireless Settings······································································································· 17 Basic Settings····································································································· 17 Advanced Settings······························································································ 18 Security Settings································································································· 20 Access Control ··································································································· 23 WDS Settings ····································································································· 25 WPS Settings ····································································································· 27 NAT Settings·············································································································· 29 NAT Settings······································································································· 29 Virtual Server······································································································ 30 Virtual DMZ········································································································· 32 Firewall Settings ········································································································ 33 IP Filter ··············································································································· 33 Port Filter············································································································ 35 MAC Filter ·········································································································· 37 Website Filter······································································································ 38 Services Settings······································································································· 39 DDNS Settings ··································································································· 39 UPnP Settings ···································································································· 40 System Log Settings··························································································· 41 Date/Time Settings ····························································································· 42 Management·············································································································· 43 Admin Account···································································································· 43 Ping Test············································································································· 44

Information················································································································· 45 System Information····························································································· 45 Packet Statistics ································································································· 46 Routing Table······································································································ 46 System Log ········································································································ 47 Logout························································································································ 47 Logout ················································································································ 47 Reboot················································································································ 47

check all the contents of this package. The product package should include the following: 1. One Wireless Router 2. One power adapter 3. One User Manual (CD) 4. One detachable antenna Introduction To Wireless Router General Description The ENCORE 802.11n Wireless Router is compatible with IEEE802.11n standard, which supports data rate up to 300 Mbps in 2.4 GHz band, which is also compatible with IEEE 802.11g/b wireless devices. The router allows multiple users to share one broadband connection, as well as secures your private network. With its built-in 4-port switch and wireless AP, LAN users can share files, printers, or playing network games all at a blazing speed. To provide a secure wireless network, this router supports wireless data encryption with 64/128-bit WEP, WPA and WPA2. Network Address Translation (NAT) Firewall is also support to shield your communications and network from hackers and wireless eavesdroppers. The Wireless Router built-in with 4-port 10/100Mbps Fast Ethernet Switch is the latest generation of Wireless router product for Home/Office and SOHO users. This full-feature and self-contained compact Wireless Router will be fully for broadband access in both of LAN and Wireless environment. This device has been specifically designed to provide LAN and Wireless users the most cost-effective method with multiple accesses to the Internet at the cost of a single public IP address（IP Sharing） and enjoy the true Plug-and-Play installation. Moreover, the built-in 4-port 10/100Mbps switch lets users plug the network cable into the device without buying additional switch. This device is also an Access Point. It has a built-in wireless LAN. Users can connect to Internet using wireless network interfaces anywhere within the range of its radio transmission. It’s ideal for SOHO users who require instant and convenient access to Internet without the restriction of connecting cables.

„ Compatible with IEEE 802.11n, 802.11g/b wireless standards. „ Provides three 802.11n/g/b wireless Reverse SMA detachable antennas „ High speed transfer data rate up to 300Mbps „ Supports wireless data encryption with 64/128-bit WEP, WPA and WPA2 „ Supports authentication for wireless connectivity based on ESSID „ Supports Multiple BSSID. „ Provides MAC access control and hidden SSID function „ WDS supported with WEP, TKIP and AES encryption „ Channel: USA 11, Europe 13 „ Supports NAT IP Sharing „ Supports WAN connection type-Static IP, PPPoE, PPTP, & DHCP client „ SPI Anti-DoS Firewall; Virtual DMZ; DNS relay; UPnP „ Provides DHCP server and client „ Supports ALG for FTP, NetMeeting, DDNS (DynDNS, TZO) „ Supports QoS:WMM „ Supports firmware upgrade function via Web „ Supports system log „ Certifications: FCC Class B, CE Mark, VCCI Class B 2

The front panel of the Wireless Router: LED Definitions z Status LED The LED will be dark for a few seconds when the system is started. After that, the LED will blink periodically to show the Wireless Router is working normally. If the LED stays green/dark that means the system failed, you need to contact your agent or try to reboot the system. z WLAN LED I. When Wireless AP is ready for data transmitting and receiving, it is steady green. II. When the data is transmitting or receiving, it is blinking green. z LAN LEDs Every port has an Act/Link LED. Steady green (link state) indicates that the port has good linkage to its associated devices. Flashing green indicates that the port is receiving or transmitting data between its associated devices. z WAN LED The LED stays light (green) means the WAN port has good linkage to its associated devices. The LED will blink green when there is traffic transverse the port. z Setup Button We provide this setup button to help users connecting this router to Internet quickly. 3

The rear panel of the Wireless Router is shown below. Power Connection Plug the circle end of the power adapter firmly into the rear panel of the Wireless Router, and the other end put into an electric service outlet then the system is ready. Restore Default Button 1. Push the button for more than 5 seconds and then release it, the system will return to factory default setting. In the meantime, system rewrites flash to default value and Status LED halts for a while. Approximately 60 seconds later, the Status LED blinks green periodically, now the whole system parameters have returned to factory default value. If the process has been interrupted by any reason (power off…), the system will fail. Before performing the process, ensure a safe operating environment please! 2. To reboot the Router, press the button for 2-5 seconds and then release it, and all the setting won’t be erased. Wait for the Router to complete the reboot, and then you can start to use it. Warning：Incomplete factory setting recovery procedure will cause the Wireless Router malfunction！If you are unfortunately in this situation, do not try to repair it by yourself. Consult your local distributor for help! 4

This Chapter provides a step-by-step guide to the installation and configuration of the Wireless Router. We suggest you go over the whole chapter and then do more advanced operation. Network configuration setup Steps to build up the network: ¾ Connect the ADSL or Cable modem to the Ethernet WAN port on the back of the Wireless Router by using the UTP cable. ¾ Connect the phone line from the wall socket to the line-in port on the ADSL modem, or the coaxial cable to the line-in port on the Cable modem. ¾ Plug-in the power adapter to the modem and turn on the power. Install the Ethernet card into the computer by referring to the User Guide that came with the card. ¾ Connect the computer to the Wireless Router by using standard twisted-pair Ethernet cable from the computer’s Ethernet card to an 10/100Mbps Ethernet port on the back of the Wireless Router. ¾ Plug-in the power adapter to the Router and the other side to the wall outlet. Computer configuration setup In order to communicate with this Wireless Router, you have to configure the IP addresses of your computer to be compatible with the device. The router supports DHCP server and it is enabled as default. Users that configure your IP address as “Obtain an IP address automatically” may skip the following IP configuration instruction. Note: 1. The default network setting of the device: IP address: 192.168.1.1 Subnet Mask: 255.255.255.0 DHCP Server: enabled 2. In the following TCP/IP configuration guide, the IP address “192.168.1.2 ” is assumed to be your IP address if you want to specify IP addresses manually. Please DO NOT choose “192.168.1.1” for the IP address (192.168.1.1) has been set as the default IP for this device. 3. The following TCP/IP configuration guide uses windows XP as the presumed operation system. 5

1. If you are in Classic Start menu view, click Start > Settings > Control Panel > Network Connections. If you are in Start menu view, click Start > Control Panel > Network Connections. 2. Double click Local Area Connection. 3. Choose Internet Protocol (TCP/IP) and click Properties. 4. You may choose “Obtain an IP address automatically”(recommend) to get IP address automatically or choose “Use the following IP address” to specify IP addresses manually. Please click the OK button after your configuration. 6

In order to make the whole network operate successfully, it is necessary to configure the Wireless Router through your computer has a WEB browser installed. Please follow up the steps listed below. 1. Double click the Internet WEB browser icon on your desktop screen (Netscape Communicator 4.0 and Internet Explorer 3.0 or update version) 2. Type 192.168.1.1 into the URL WEB address location and press Enter. 3. The Login Name and Password Required window appears. - Select Administrator in the Login Name drop list (default value). - Enter admin in the Password location (default value). - Click Login button. 7

After the password authorization, the Information page shows up as the home page of the Graphic User interface. You may click on each folder on left column of each page to get access to each configuration page. Note: Please note that you should click the Save Settings button to apply your configuration to this device. You can also restore the default settings by clicking the Reset Settings button. 8

This page allows users to configure those parameters for connecting to Internet. You may select the WAN Access Type from the “My Connection type” column and configure parameters for each mode. 9

Items Information IP Address, Subnet Mask and Default Gateway Fill in the IP address, Subnet Mask and Default Gateway that provided by your Internet Service Provider (ISP). Primary and 2nd DNS server To specify the Domain Name Server (DNS). Enter the DNS provided by your ISP in 1st and 2nd server. Static IP MTU To enable the Maximum Transmission Unit of Router setup. Any packet over this number will be chopped up into suitable size before sending. Larger number will enhance the transmission performance. Enter the MTU number in the blank to set the limitation (default 1500bytes). Host Name Name of this device. Ping from WAN Mark the check box to enable others detecting this device from WAN, and clear the checkbox to disable. WAN Ethernet MAC Select to use the following MAC as the MAC while serving Internet: Original MAC: the MAC of the device. Manual Settings: the MAC of your computer. Click on the words in the bracket to clone your computer MAC in the blank. You can also change the MAC numbers if you need. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 10

Items Information Set DNS server If your DNS provide by ISP is dynamic, choose “Automatically”, if not choose “Manually” and enter the DNS provided by your ISP in DNS 1, 2. DHCP MTU To enable the Maximum Transmission Unit of Router setup. Any packet over this number will be chopped up into suitable size before sending. Larger number will enhance the transmission performance. Enter your MTU number in the text-box to set the limitation (default 1500bytes). Host Name Name of this device. Ping from WAN Mark the check box to enable others detecting this device from WAN, and clear the checkbox to disable. WAN Ethernet MAC Select to use the following MAC as the MAC while serving Internet: Original MAC: the MAC of the device. Manual Settings: the MAC of your computer. Click on the words in the bracket to clone your computer MAC in the blank. You can also change the MAC numbers if you need. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 11

Password Fill in the User Name and Password that provided by your ISP. The default username/password is USERNAME/PASSWORD. Set DNS server If your DNS provide by ISP is dynamic, choose “Automatically”, if not, choose “Manually” and enter the DNS provided by your ISP in DNS 1, 2. PPPoE MTU To enable the Maximum Transmission Unit of Router setup. Any packet over this number will be chopped up into suitable size before sending. Larger number will enhance the transmission performance. Enter your MTU number in the text-box to set the limitation (default 1492 bytes). Host Name Name of this device. Ping form WAN Mark the check box to enable others detecting this device from WAN, and clear the checkbox to disable. WAN Ethernet MAC Select to use the following MAC as the MAC while serving Internet: Original MAC: the MAC of the device. Manual Settings: the MAC of your computer. Click on the words in the bracket to clone your computer MAC in the blank. You can also change the MAC numbers if you need. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 12

To set up the configuration of LAN interface, private IP of you router LAN port and subnet mask for your LAN segment. 13

Subnet Mask Subnet Mask of you LAN (default 255.255.255.0). DNS Proxy DNS proxy takes DNS queries from the local network and forwards them to an Internet DNS. Mark the check box to enable DNS Proxy function or clear to disable. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. DHCP Server Settings Items Information Enable DHCP Server To give your LAN Client an IP, you have to enable DHCP server. If not, manual setting up your client IP is necessary when you want to use the router as your client’s default gateway. DHCP IP Range Specify the DHCP Client IP address range default (100~150). DHCP Lease Time The time for the device to recycle and give out DHCP IP (default 86400). * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. DHCP Server Settings The information of type, hostname, MAC, IP, description and expire time of the DHCP clients that have connected with this device. 14

or data flows. 15

You can setup the total upload/ download bandwidth manually (default 102400). Bandwidth QoS Settings Items Information Enable this Rule Mark to enable the configuration, and clear to disable. Type Select the type of download or upload. LAN IP Address Fill in the MAC address that you are going to control. Priority Select the transmission priority of low, medium, high, or highest. Bandwidth Fill in the minimum and maximum bandwidth. Comment Give a definition to the LAN IP Address. Action After configuring the above settings, click Add to add a new list in the following MAC Access Control List. The Change button can be used to change the configuration. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. Bandwidth QoS Settings Lists the Bandwidth QoS Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list. 16

associate with your AP. Items Information Enable Wireless Mark the checkbox to enable Wireless interface or uncheck to disable. Wireless Mode To select a band for this device to match 802.11g/b/n mixed, 802.11g/b mixed, 802.11b, 802.11g, or 802.11n. Country Select the region you live. Wireless Channel Select a channel for the wireless network of this device. SSID Service set identifier for the name of the wireless network. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 17

changing these parameters unless you know what changes will be there on this router. 18

Items Information Hide SSID Mark to disable SSID from broadcasting. As default, this device broadcasts its SSID to allow every wireless station located within the coverage of this wireless router to discover this wireless router easily. Beacon Period The period of time a beacon is broadcasted (default 100ms). DTIM Period The beacon of a Delivery Traffic Indication Message is broadcasted (default 1 beacon). RTS Threshold If the packet size is smaller than the Request To Send threshold, the wireless router will not send this packet by using the RTS/CTS mechanism (default 2347 bytes). Fragment Threshold Specifies the maximum size of packet during the data transition. A higher value brings a better performance (default 2346 bytes) Tx Power Select the Transmission Power of very weak, weak, medium, and strong according to your demand. g/b Protection Allows the adapters search for 802.11g/b singles only. Select “Auto” to turns it on or off automatically, select “Always On” to support protection or select “Always Off” to disable this function. Support WMM To enable/disable Wi-Fi Multimedia function. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 802.11n Wireless advance Settings Items Information HT Operation Mode Select the mixed or green field mode as the Hyper Throughput operation mode. HT Channel Bandwidth Select the 40MHz or 20MHz as the channel bandwidth. HT Guard Interval Select 400ns or 800ns as the interval time. Enable HT TX Aggregate MSDU Mark to enable Hyper Throughput TX Aggregate MAC Service Data Unit, and clear to disable. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 19

and WPA encryption to secure your wireless network. As default, the authentication is configured as safe mode. Please select None/WEP/WPA (Personal) in the drop list. If you select none, any data will be transmitted without encryption and any station can access the router. 20

wireless router without WEP encryption. Shared Key: Wireless AP can associate with this wireless router only with WEP encryption. Default Key ID Select to use the WEP key value of 1,2,3 or 4 as in the following settings. WEP Key 1, 2, 3 and 4 Select ASCII or Hex to setup the key value (default 012345). * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 21

modes of auto, WPA only, or WPA2 only. WPA Encryption Select TKIP / AES, TKIP or AES as WPA encryption. Pre-Shared Key Select the key format of Pass Phrase or Hex. Enter the Pre-Shared Key according to the key format you select (default 01234567). WPA ReKey Method To enable/disable WPA rekey method by time or by packet. WPA ReKey Interval Enter the numbers to setup the WPA rekey interval. Pairwise Master Key Cache Interval Select 1, 5, 10, 20, 30, 60, or 120 minuets as the cache interval time. Pre-Authentication Support Mark this checkbox to enable pre-authentication function, and clear to disable. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 22

this page. You may select “Allow Listed” to allow those allowed MAC addresses or select “Deny Listed” to ban those MAC addresses from accessing to this device. 23

Items Information Enable this Rule Mark to enable the configuration, and clear to disable. MAC Address Fill in the MAC address that you are going to control. Description Give a definition to the MAC Address. Action After configuring the above settings, click Add to add a new list in the following MAC Access Control List. The Change button can be used to change the configuration. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. MAC Access Control List Lists the MAC Access Control Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list. Current Associated Client List Lists the current associated client connected to this device. Click on the list to add it into the MAC Access Control List then to do more configurations on it. 24

wirelessly. To make it work, you must ensure that these APs and the Router are in the same Channel and add these APs MAC Address and Comment values into the WDS list. AP+WDS (AP Repeater) 25

Auto (AP Bridge) Items Information WDS Select the option in the drop list to enable AP+WDS (AP Repeater), WDS (AP Bridge) or Auto (AP Bridge) as WDS format. Encryption Type Select the option in the drop list to enable WEP, WPA/TKIP, and WPA/AES encryption types. If you select None, any data will be transmitted without encryption and any station can access the router. WPA Encryption Key For encryption type of WPA/TKIP and WPA/AES, you have to fill in the WPA encryption key. Please use Pass Phrase (8~32bytes) key format. WDS AP MAC List For encryption type of WPA/TKIP and WPA/AES, you have to fill in the WDS AP MAC. You can fill up to 4 sets of WDS AP MAC lists. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 26

Items Information WPS Config Method PIN method (Personal Identification Number): read the PIN from either a sticker on the new STA or a display. PBC method (Push Button Communication): in which the user simply has to push a button, either an actual or virtual one, on both the AP and the new STA. Add Enrollee PIN Code Fill in the PIN code to enrollee device. Click on Build WPS Connection button to execute. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. WPS Information Shows the information of WPA configured, status, SSID, authentication mode, and pre-shared key. Click on Refresh button to refresh the information. 28

addresses of IP packets as they pass through a Router or firewall. NAT enable multiple hosts on a private network to access the Internet using a single public IP address. NAT & ALG Settings Click on the checkbox to enable NAT function, IPSec (IP Security), PPTP (point-to-point tunneling protocol), and L2TP (layer 2 tunneling protocol) pass through on Virtual Private Network (VPN), or clear to disable. Fill in the port number in the Non-standard FTP port blank if you need. ALG Settings Click on the checkbox to enable SIP (session initiation protocol), NetMeeting, Window Messenger File Transfer, and StarCraft/Battle.net ALG. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 29

refresh the page. 30

Items Information Enable this Rule Mark to enable the configuration, and clear to disable. Application Select Select an application for your demand. WAN Port Fill in the port number of WAN. Protocol Select the protocol type of TCP, UDP or Both LAN Server IP Fill in the IP of your LAN Server. LAN Port Fill in the port number of LAN. Action After configure the above settings, click Add to add a new list in the following IP Filter Rule List. The Change button can be used to change the configuration. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. Virtual Server Mapping List Lists the Virtual Server Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list. 31

ports on the router. The router will forward all unspecified incoming traffic to the host specified in this page. To configure it, mark to enable and then enter the Host IP (private IP address) and click Save Settings to enact the setting. 32

consideration. You can set up the filter against the IP addresses to block specific internal users from accessing the Internet. After marking or clearing the enable checkbox, it takes 5 seconds for this device to refresh the page. 33

Items Information Enable this Rule Mark to enable the configuration, and clear to disable. IP Address Fill in the IP address that you are going to filter. Protocol Select the protocol type of TCP, UDP or Both Filter Mode Select the filter mode of Always or by Schedule Date Define Time Define For filter mode of by Schedule, you have to define the filter date and time. Action After configure the above settings, click Add to add a new list in the following IP Filter Rule List. The Change button can be used to change the configuration. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. IP Filter Rule List Lists the IP Filter Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list. 34

also restricting the LAN users. Port filtering restricts certain type of data packets from your LAN to Internet through the router. After marking or clearing the enable checkbox, it takes 5 seconds for this device to refresh the page. 35

Items Information Enable this Rule Mark to enable the configuration, and clear to disable. Port Range Fill in the port range that you are going to filter. The valid numbers are 1~65535. Protocol Select the protocol type of TCP, UDP or Both Filter Mode Select the filter mode of Always or by Schedule Date Define Time Define For filter mode of by Schedule, you have to define the filter date and time. Action After configure the above settings, click Add to add a new list in the following IP Filter Rule List. The Change button can be used to change the configuration. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. Port Filter Rule List Lists the Port Filter Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list. 36

consideration. You can set up the filter against the MAC addresses to block specific internal users from accessing the Internet. After marking or clearing the enable checkbox, it takes 5 seconds for this device to refresh the page. MAC Filter Settings Items Information Enable this Rule Mark to enable the configuration, and clear to disable. MAC Address Fill in the MAC address that you are going to filter. Filter Mode Select the filter mode of Always or by Schedule Date Define Time Define For filter mode of by Schedule, you have to define the filter date and time. Action After configure the above settings, click Add to add a new list in the following IP Filter Rule List. The Change button can be used to change the configuration. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. MAC Filter Rule List Lists the MAC Filter Settings you have added before. Click on the list to change 37

Website Filter The Website Filter allows users to prevent certain website from accessing by users in LAN. This filter will block those websites that contain certain keywords. After marking or clearing the enable checkbox, it takes 5 seconds for this device to refresh the page. Website Filter Settings Items Information Enable this Rule Mark to enable the configuration, and clear to disable. IP Address Fill in the local IP address that you want to restrain it from serving the filtering websites. Website or Key Word Fill in the name or keywords of the website to block. Action After configure the above settings, click Add to add a new list in the following Website Filter Rule List. The Change button can be used to change the configuration. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. Website Filter Rule List Lists the Website Filter Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list. 38

fixed and easy-to–remember hostname. Items Information Enable DDNS Mark to enable the configuration, and clear to disable. Service Provider The website that provides DDNS service. Please select DynDns.org, No-IP.com or TZO from the drop list. Domain Name The hostname that you have applied for the device. User Name/Email DDNS login account. For DynDNS users, please fill in your user name; for No-IP and TZO users, please fill in your email address (default USER). Password/Key The password of your DDNS service account (default PASSWORD). Confirmed Password Retype the password to confirm. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 39

simplify the implementation of networks in the home (data sharing, communications, and entertainment) and corporate environments. This page allows user to monitor the information of UPnP clients. Mark or clear the checkbox to enable or disable UPnP IGD, and then click Save Settings to enact your settings. 40

The System Log Settings page shows the information of the current activities on the router. Items Information System Log Mark to enable the configuration, and clear to disable. Log Type Select “cleanup when reboot” or “save log message” as the log type. Log Message Size Select the log message size of 4, 8, or 32 Kbytes. Remote Log Mark to enable the following configuration, and clear to disable. Remote Log Server Address Fill in the sever address for remote log. Remote Log Server Port Fill in the sever port for remote log. Log to Remote and Local To enable/disable log to remote and local * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 41

the date and time from the drop list and click the Save Settings button. To synchronize time from a timeserver, please enter the update interval hour numbers, select an NTP server from the drop list or manually enter a private NTP server and then click the Save Settings button. Mark the Daylight Saving checkbox if you want to apply it on system time. Manual Time Setting NTP Time Server 42

page, you can reset the password of the admin account and setup a designated IP to remote control this device. Remote Administration Items Information Remote Control Mark this checkbox to allow remote PC accessing the configuration interface of this router. HTTP port for remote The HTTP port for accessing this management interface (default 8080). Remote Control IP The permitted IP for accessing. The default IP 0.0.0.0 allows all IP addresses form accessing. Update button Click on this button to update your setting. Admin Accounts Items Information Access Level Select an access level of admin or guest. Password The new password for the admin account Confirm Password Fill in the new password again Action Click Change button to apply the new password. 43

IP then click on the Ping Test button to view the result information. Config The Config page allows users to backup and download the configuration status of the device or restore the factory default configuration. Items Information Save Settings to File Click on the Save button to save settings. Load Settings from File Click Browse to select the file and then click Reload to start the process. Please wait for it to complete. Reset Settings to Default Click Reset to Default to start the process and it will be completed till the status LED starts blinking. 44

could upgrade the firmware you got in this page. To upgrade the firmware, please click on the Browse button, locate the firmware in your computer and then click the Upload button to execute. Information System Information This information page shows the current settings of this device. You could check if the parameters match your configuration. 45

the status and performance of this router including interface, receiving/sending packets, and receiving/sending errors. Routing Table This page shows the routing table in this router. Users can get connecting information including destination, gateway, net mask, flags, metric, ref, use and interface. 46

list. Logout Logout Click the Logout button to log out the admin account from this system Reboot Click the reboot button to restart this system. This may cost 1 minute to restart the system. Please wait upon restarting. 47

WAN: One RJ45 port 3* 802.11n/g/b wireless reverse SMA detachable antenna WAN Connection Ethernet 10/100 Mbps Cable Connections RJ-45 (10BASE-T): Category 3,4,5 UTP RJ-45 (100BASE-TX): Category 5 UTP Transmission Mode Auto-Negotiation (Full-duplex, Half-duplex) LED indications 1*Power, 1*WAN, 4*LAN, 1*WLAN Security 64/128-bit WEP, WPA, WPA2 Receiver Sensitivity 11Mbps-91dBm, 54Mbps-78dBm, 300mbps -69dBm Transmit Power 11Mbps 19dBm, 54Mbps 16dBm, 11n 20MHz and 11n 40MHz 16dBm Range Coverage Indoor 35~100 meters Outdoor 100~300meters. Emission FCC CLASS B, CE Operating Temperature 00 ~ 400C (320 ~ 1040F) Operating Humidity 10% - 90% RH non-condensing Power Supply External Power Adapter, 12VDC/ 1A 48