Integra DTR-80.1 Instruction Manual

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radia- tors, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are pro- vided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience recepta- cles, and the point where they exit from the appara- tus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manu- facturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or plug is dam- aged, B. If liquid has been spilled, or objects have fallen into the apparatus, C. If the apparatus has been exposed to rain or water, D. If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the oper- ating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified tech- nician to restore the apparatus to its normal operation, E. If the apparatus has been dropped or damaged in any way, and F. When the apparatus exhibits a distinct change in performance this indicates a need for service. 16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous volt- age points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit. 17. Batteries Always consider the environmental issues and fol- low local regulations when disposing of batteries. 18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is ade- quate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue- like gap for warm air to escape. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR AVIS PORTABLE CART WARNING S3125A

only, recording copyrighted material is illegal with- out the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not user- serviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit. 3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild deter- gent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thin- ners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel let- tering. 4. Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SEC- TION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz). The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times. Pressing the [On/Standby] button to select Standby mode does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet. 5. Preventing Hearing Loss Caution Excessive sound pressure from earphones and head- phones can cause hearing loss. 6. Batteries and Heat Exposure Warning Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like. 7. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by the dealer from whom you purchased this unit. 8. Handling Notes • If you need to transport this unit, use the original packaging to pack it how it was when you origi- nally bought it. • Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case. • This unit’s top and rear panels may get warm after prolonged use. This is normal. • If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally. For U.S. models FCC Information for User CAUTION: The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment generates, uses and can radiate radio fre- quency energy and, if not installed and used in accor- dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partic- ular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit dif- ferent from that to which the receiver is connected. • Consult the dealer from whom you purchased this unit or an experienced radio/TV technician for help. For Canadian Models NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. Modèle pour les Canadien REMARQUE: CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA. Sur les modèles dont la fiche est polarisée: ATTENTION: POUR ÉVITER LES CHOCS ÉLEC- TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRE- SPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Please read this manual thoroughly before making con- nections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV receiver. Please retain this manual for future reference. Supplied Accessories Make sure you have the following accessories: * In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operations are the same regardless of color. Remote controller & two batteries (AA/R6) Speaker setup microphone Indoor FM antenna AM loop antenna Power cord (Plug type varies from country to country.) Speaker cable labels 3 2 1 Speaker Cable FRONT LEFT FRONT LEFT FRONT RIGHT FRONT RIGHT SURROUND BACK RIGHT SURROUND BACK RIGHT FRONT HIGH LEFT FRONT HIGH LEFT FRONT HIGH RIGHT FRONT HIGH RIGHT FRONT LEFT FRONT LEFT FRONT RIGHT FRONT RIGHT SURROUND LEFT SURROUND LEFT SURROUND RIGHT SURROUND RIGHT SURROUND LEFT SURROUND LEFT SURROUND RIGHT SURROUND RIGHT SURROUND BACK RIGHT SURROUND BACK RIGHT CENTER CENTER CENTER CENTER SURROUND BACK LEFT SURROUND BACK LEFT SURROUND BACK LEFT SURROUND BACK LEFT FRONT HIGH LEFT FRONT HIGH LEFT FRONT HIGH RIGHT FRONT HIGH RIGHT FRONT WIDE LEFT FRONT WIDE LEFT FRONT WIDE RIGHT FRONT WIDE RIGHT FRONT WIDE LEFT FRONT WIDE LEFT FRONT WIDE RIGHT FRONT WIDE RIGHT SP-B/ZONE2 LEFT SP-B/ZONE2 LEFT SP-B/ZONE2 RIGHT SP-B/ZONE2 RIGHT SP-B/ZONE2 LEFT SP-B/ZONE2 LEFT SP-B/ZONE2 RIGHT SP-B/ZONE2 RIGHT

Precautions.......................................................................3 Supplied Accessories .......................................................4 Features............................................................................6 Front & Rear Panels .........................................................8 Front Panel ...................................................................8 Display ........................................................................10 Rear Panel..................................................................11 Remote Controller...........................................................14 Installing the Batteries.................................................14 Aiming the Remote Controller.....................................14 Controlling the AV Receiver........................................15 About Home Theater ......................................................17 Enjoying Home Theater ..............................................17 Connecting the AV receiver ............................................18 Connecting Your Speakers.........................................18 Bi-amping the Front Speakers ....................................21 Bridging the Front Speakers .......................................22 Connecting Passive Subwoofers ................................23 Connecting Antenna ...................................................24 About AV Connections................................................26 Connecting Components with HDMI...........................27 Connecting Both Audio & Video..................................29 Which Connections Should I Use? .............................29 Connecting a TV or Projector......................................32 Connecting a DVD Player...........................................33 Connecting a VCR or DVD Recorder for Playback.....35 Connecting a VCR or DVD Recorder for Recording...36 Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source..............................................37 Connecting a Game Console......................................38 Connecting a Camcorder or Other Device..................39 Connecting a CD Player or Turntable.........................40 Connecting a Cassette, CDR, MiniDisc, or DAT Recorder....41 Connecting a Power Amplifier.....................................42 Connecting an RI Dock...............................................43 Connecting a Universal Port Option Series ................43 Connecting Integra/Onkyo u Components...............44 Connecting the Power Cord........................................44 Turning On the AV receiver ............................................45 Turning On and Standby.............................................45 First Time Setup .............................................................46 Monitor Setup..............................................................46 Selecting the Language used for the onscreen setup menus ...47 Using the Onscreen Setup Menus..............................48 Using the Display to change the settings....................48 Monitor Out Setup.......................................................49 Video Input Setup .......................................................51 Digital Audio Input Setup ............................................53 Analog Audio Input Setup ...........................................54 Speaker Settings.........................................................54 TV Format Setup (Australian models).........................56 FM/AM Frequency Step Setup....................................56 Changing the Input Display.........................................57 Audyssey MultEQ® XT Room Correction and Speaker Setup..........................................................58 Basic Operations ............................................................64 Selecting the Input Source..........................................64 Adjusting the Bass & Treble........................................65 Displaying Source Information....................................65 Setting the Display Brightness....................................66 Muting the AV Receiver ..............................................66 Using the Sleep Timer ................................................66 Selecting Speaker Layout...........................................66 Using Headphones .....................................................66 Using Easy Macros.....................................................67 Listening to the Radio .....................................................69 Using the Tuner ..........................................................69 Presetting AM/FM Stations .........................................70 Listening to Satellite Radio (North American models)....71 Using RDS (Australian models) ..................................82 Universal Port Option UP-A1 Dock for iPod ................... 84 About the UP-A1 Dock ............................................... 84 Compatible iPod models............................................. 84 Function Overview...................................................... 84 Controlling iPod .......................................................... 85 Recording ....................................................................... 87 Using the Listening Modes ............................................. 88 Selecting Listening Modes.......................................... 88 Listening Modes Available for Each Source Format... 89 About the Listening Modes ......................................... 96 Advanced Setup ............................................................. 99 Onscreen Setup Menus.............................................. 99 Input/Output Assign .................................................. 100 Speaker Setup.......................................................... 102 Audio Adjust ............................................................. 106 Source Setup............................................................ 110 Assigning Listening Modes to Input Sources............ 115 Miscellaneous (Volume/OSD) Setup ........................ 116 Hardware Setup........................................................ 117 Lock Setup................................................................ 122 Digital Input Signal Formats ..................................... 122 Using the Audio Settings .......................................... 123 NET/USB...................................................................... 126 About NET ................................................................ 126 Connecting the AV Receiver .................................... 126 Listening to Internet Radio........................................ 127 Playing Music Files on a Server ............................... 128 Network Settings ...................................................... 132 About USB................................................................ 133 Playing Music Files on a USB Device ...................... 134 Multi Zone..................................................................... 136 Multiroom Capability ................................................. 136 Connecting Zone 2 ................................................... 137 Connecting Zone 3 ................................................... 139 Connecting Zone 4 ................................................... 140 Setting the Powered Zone 2/3/4 ............................... 141 Setting the Multi Zone............................................... 142 Using Zone 2/3/4 ...................................................... 143 Using the 12V Triggers............................................. 145 Using the Remote Controller in Zone 2/3/4 and Multiroom Control Kits............................................ 147 Controlling Other Components..................................... 148 Preprogrammed Remote Control Codes .................. 148 Looking up for Remote Control Code ....................... 148 Entering Remote Control Codes............................... 150 Remote Control Codes for Integra/Onkyo Components Connected via u ............................ 151 Resetting Remote Mode Buttons.............................. 151 Resetting the Remote Controller .............................. 151 Controlling a TV........................................................ 152 Controlling a DVD Player or DVD Recorder ............. 153 Controlling a VCR or PVR ........................................ 154 Controlling a Satellite Receiver or Cable Receiver... 155 Controlling a CD Player, CD Recorder or MD Recorder ... 156 Controlling an RI Dock.............................................. 157 Controlling a Cassette Recorder .............................. 158 Activities Setup ......................................................... 159 Learning Commands ................................................ 161 Using Normal Macros ............................................... 162 Troubleshooting............................................................ 163 Specifications (DTR-70.1) ............................................ 169 Specifications (DTR-80.1) ............................................ 170 Video Resolution Chart................................................. 171 Introduction Connection Turning On & First Time Setup Basic Operations Using the Listening Modes Advanced Setup NET/USB Multi Zone Controlling Other Components Others * To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VCR/DVR] button, press the [On/Standby] button (see page 163).

• 200 Watts/Channel @ 6 ohms (IEC) • 250 Watts/Channel @ 6 ohms (JEITA) (DTR-80.1) • 145 Watts/Channel @ 8 ohms (FTC) • 220 Watts/Channel @ 6 ohms (IEC) • 280 Watts/Channel @ 6 ohms (JEITA) • WRAT–Wide Range Amplifier Technology (5 Hz-100 kHz bandwidth) • Linear Optimum Gain Volume Circuitry • 3-Step Inverted Darlington Circuitry • H.C.P.S. (High Current Power Supply) Massive High Power Transformer • Toroidal transformer (DTR-80.1) Processing • THX Ultra2 Plus*1 Certified • HQV-Reon-VX Video Processing with 1080p Video Upscaling of All Video Sources via HDMI • HDMI ver.1.3a with (Deep Color, x.v.Color, Lip Sync, DTS*2-HD Master Audio, Dolby TrueHD*3, DSD and Multi-CH PCM) • Dolby Pro Logic IIz*3 – New Surround Format (front- high) • Audyssey Dynamic Surround Expansion™*8 for New Surround Channels (front-wide/front-high) • 4 DSP Modes for Gaming; Rock/Sports/Action/RPG • Non-Scaling Configuration • Direct Mode • Music Optimizer*4 for Digital Music Files • A-Form Listening Mode Memory • Latest Burr-Brown 192 kHz/32-Bit DACs Improve Jitter Performance for Cleaner Sound (DTR-80.1) • Burr-Brown 192 kHz/24-Bit DACs Improve Jitter Performance for Cleaner Sound (DTR-70.1) • Three TI (Aureus) 32-bit Processing DSP • Neural Surround Decoding*9 • DSD Direct Connections • 7 HDMI*5 Inputs and 2 Outputs (DTR-70.1) • 8 HDMI*5 Inputs and 2 Outputs (DTR-80.1) • Integra/Onkyo for System Control • 6 Digital Inputs (3 Optical/3 Coaxial) (DTR-70.1) • 7 Digital Inputs (4 Optical/3 Coaxial) (DTR-80.1) • Universal Port for UP-A1 (Dock for the iPod)/HD Radio™*6 tuner module (North American models)/ DAB+ tuner module (Australian models) • 2 Independent Subwoofer Pre Outs • SIRIUS*7 Satellite Radio Connectivity (North Ameri- can models) • Banana Plug-Compatible Speaker Posts • Powered Zone 2/3/4 • Internet Radio* Connectivity (SIRIUS Internet Radio*7/vTuner/Pandora/Rhapsody) * Services available may vary depending on the region. • Network Capability for Streaming Audio Files • Bi-Amping and BTL Capability • USB Port for a USB Mass Storage Device (Audio Only) Miscellaneous • 40 SIRIUS*7/AM/FM Presets (North American mod- els) • 40 AM/FM Presets (Australian models) • Dolby Volume*3 • Audyssey MultEQ® XT*8 to Correct Room Acoustic Problems • Audyssey Dynamic EQ™*8 for Loudness Correction • Audyssey Dynamic Volume™*8 • Crossover Adjustment (40/45/50/55/60/70/80/90/100/110/120/130/150/200 Hz) • A/V Sync Control Function (up to 250 ms) • Bi-Directional Preprogrammed (with onscreen dis- play setup) RI-Compatible Learning Remote with 4 Activities and Mode-Key LEDs • ISF (Imaging Science Foundation) Video Calibration *1. THX and Ultra2 Plus are trademarks of THX Ltd. THX may be registered in some jurisdictions. All rights reserved. Surround EX is a trademark of Dolby Laboratories. Used with permission. *2. Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks of DTS, Inc. © 1996-2008 DTS, Inc. All Rights Reserved. *3. Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “Surround EX” and the double-D symbol are trademarks of Dolby Laboratories. *4. Music Optimizer™ is a trademark of Onkyo Corporation. *5. HDMI, the HDMI logo and High Definition Multimedia Inter- face are trademarks or registered trademarks of HDMI Licens- ing, LLC.

trademarks of iBiquity Digital Corporation. To receive HD Radio broadcasts, you must install an Onkyo UP-HT1 HD Radio tuner module (sold separately). *7. SIRIUS, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries. All other marks and logos are the property of their respective owners. All rights reserved. SIRIUS and XM subscriptions sold separately. Taxes and a one-time activation fee may apply. XM tuners and home docks or SIRIUS tuners (each sold separately) are required to receive the SIRIUS or XM satellite radio service. All program- ming and fees subject to change. It is prohibited to copy, decom- pile, disassemble, reverse engineer, hack, manipulate or otherwise make available any technology or software incorpo- rated in receivers compatible with the SIRIUS or XM Satellite Radio Systems. Service not available in Alaska and Hawaii. *8. Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending. Audyssey MultEQ® XT, Audyssey Dynamic Surround Expansion™, Audyssey Dynamic Volume™ and Audyssey Dynamic EQ™ are trademarks of Audyssey Laboratories. *9. Neural Surround is a trademark owned by Neural Audio Corpo- ration, THX is a trademark of THX Ltd., which may be regis- tered in some jurisdictions. All rights reserved. * “Xantech” is a registered trademark of Xantech Corporation. * “Niles” is a registered trademark of Niles Audio Corporation. * Apple and iPod are trademarks of Apple Inc., registered in the U.S. and other countries. * “x.v.Color” is a trademark of Sony Corporation. * Rhapsody and the Rhapsody logo are registered trademarks of RealNetworks, Inc. * “DLNA®, the DLNA Logo and DLNA CERTIFIED™ are trademarks, service marks, or certification marks of the Digital Living Network Alliance.” * Re-Equalization and the “Re-EQ” logo are trademarks of THX Ltd. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassem- bly is prohibited. THX Ultra2 Plus Before any home theater component can be THX Ultra2 Plus certified, it must pass a rigorous series of quality and performance tests. Only then can a product feature the THX Ultra2 Plus logo, which is your guar- antee that the Home Theater products you purchase will give you superb performance for many years to come. THX Ultra2 Plus requirements define hundreds of parameters, including power amplifier performance, and pre-amplifier performance and operation for both digital and analog domains. THX Ultra2 Plus receivers also feature proprietary THX technologies (e.g., THX Mode) which accurately translate movie soundtracks for home theater playback.

The actual front panel has various logos printed on it. They are not shown here for clarity. The page numbers in parentheses show where you can find the main explanation for each item. a On/Standby button (45) This button is used to set the AV receiver to On or Standby. b Standby indicator (45) Lights when the AV receiver is in Standby mode, and it flashes while a signal is being received from the remote controller. c Zone 2 indicator (143) Lights when Zone 2 is selected. d Zone 3 indicator (143) Lights when Zone 3 is selected. e Zone 4 indicator (143) Lights when Zone 4 is selected. f Remote control sensor/transmitter (14) The sensor receives control signals from the remote controller. The transmitter transmits setting data to the remote controller. g Monitor Out button (46) Used to set the “Monitor Out” setting. h Tone button (65, 144) Used to select the tone (bass and treble) for the main room and the tone and balance for Zone 2 or Zone 3. Down and Up [–]/[+] buttons (65, 144) Used to adjust the tone (bass and treble) for the main room and the tone and balance for Zone 2 or Zone 3. i Display See “Display” on page 10. j Movie/TV button (88) Selects the listening modes intended for use with movies and TV. k Music button (88) Selects the listening modes intended for use with music. l Game button (88) Selects the listening modes intended for use with video games. m Dimmer button (66) (North American models) This button is used to adjust the display brightness. RT/PTY/TP button (82) (Australian models) This button is used for RDS (Radio Data System). The [RT/PTY/TP] button does not work in areas where RDS broadcasts are not available. See “Using RDS (Australian models)” on page 82. n Memory button (70) This button is used when storing or deleting radio presets. o Tuning Mode button (69) This button is used to select the Auto or Manual tuning mode. Front Panel z x w uv t y A B C j i g f h k l m n p r o q s a b de c

The page numbers in parentheses show where you can find the main explanation for each item. p Display button (65) This button is used to display various information about the currently selected input source. q Setup button This button is used to access the onscreen setup menus that appear on the connected TV. r Arrow, Tuning, Preset and Enter buttons When the AM or FM input source is selected, the Tuning [q]/[w] buttons are used to tune the tuner, and the Preset [e]/[r] buttons are used to select radio presets (see pages 70 and 83). When the onscreen setup menus are used, they work as arrow buttons and are used to select and set items. The [Enter] button is also used with the onscreen setup menus. s Return button This button is used to return to the previously dis- played onscreen setup menu. t Master Volume control (64) This control is used to adjust the volume of the AV receiver to –Q dB, –81.5 dB through +18.0 dB (rel- ative display). The volume level can also be displayed as an abso- lute value. See “Volume Setup” on page 116. u Zone 2 and Off buttons (143) The [Zone 2] button is used to select Zone 2. The [Off] button is used to turn off the output of Zone 2. v Zone 3 and Off buttons (143) The [Zone 3] button is used to select Zone 3. The [Off] button is used to turn off the output of Zone 3. w Zone 4 and Off buttons (143) The [Zone 4] button is used to select Zone 4. The [Off] button is used to turn off the output of Zone 4. x Phones jack (66) This 1/4-inch phone jack is for connecting a stan- dard pair of stereo headphones for private listening. y Zone Level Down and Up [w]/[q] buttons (144) Used when adjusting the volume level of Zone 2, Zone 3, or Zone 4. z Setup Mic jack (59) Audyssey MultEQ® XT Room Correction and Speaker Setup microphone connects here. A Input selector buttons (64) These buttons are used to select from the following input sources: DVD/BD, VCR/DVR, CBL/SAT, Game, AUX1, AUX2, TV/Tape, Tuner, CD, Phono, Port, Net/USB. B USB port (133) A USB mass storage device, such as a USB flash drive or MP3 player, containing music files can be plugged in here and the music selected can be played through the AV receiver. C AUX1 Input (39) This input can be used to connect a camcorder, game console, and so on. There are jacks for com- posite video, analog audio, and optical digital audio. AUX1 Input HDMI (28) Used to connect an HD camcorder etc.

For detailed information, see the pages in parentheses. a Speaker/channel indicators Indicate the speaker channels used by the current listening mode. The following abbreviations indicate which audio channels are outputted for the current listening mode. b Z3 indicator (143) Lights when Powered Zone 3 is being used. c Z2 indicator (143) Lights when Powered Zone 2 is being used. d Z4 indicator (143) Lights when Powered Zone 4 is being used. e Listening mode and format indicators (88) Show the selected listening mode and audio input signal format. Audyssey (58, 104): Flashes during Audyssey MultEQ® XT Room Cor- rection and Speaker Setup. Lights when the “Equal- izer Settings” is set to “Audyssey” or Audyssey Dynamic Surround Expansion™ listen- ing mode is selected. Dynamic EQ (108): Lights when “Dynamic EQ” is enabled. Vol (108, 124): Lights when “Dynamic Volume” is enabled. Vol (107, 124): Lights when “Dolby Volume” is enabled. f NETWORK indicator (127) Lights when the Net input selector is selected. g Tuning indicators RDS (Australian models) (82): Lights when tuned to a radio station that supports RDS (Radio Data System). AUTO (69): Lights when Auto Tuning mode is selected for AM or FM radio. Goes off when Manual Tuning mode is selected. TUNED (69): Lights when tuned to a radio station. FM STEREO (69): Lights when tuned to a stereo FM station. h SLEEP indicator (66) Lights when the Sleep function has been set. i Bi AMP indicator (21) Lights when the “Speakers Type(Front)” setting is set to “Bi-Amp”. j BTL indicator (22) Lights when the “Speakers Type(Front)” setting is set to “BTL” for bridged front speaker operation. k Headphone indicator (66) Lights when a pair of headphones are plugged into the Phones jack. l Message area Displays various information. m USB indicator (134) Lights up when a USB mass storage device is detected. n Volume level (64) Displays the volume level. o MUTING indicator (66) Flashes while the AV receiver is muted. p Audio input indicators Indicate the type of audio input that’s selected as the audio source: HDMI, ANALOG, or DIGITAL. Display b e d g f a c h i j k l m n op LW: Front wide left LH: Front high left RH: Front high right RW: Front wide right FL: Front left C: Center FR: Front right SL: Surround left SW: Subwoofer (Low Frequency Effects) SR: Surround right SBL: Surround back left SB: Surround back SBR: Surround back right

a UNIVERSAL PORT This port is for connecting the component with the Universal Port option such as UP-A1 Dock. b IR IN/OUT A commercially available IR receiver can be con- nected to the IR IN jack, allowing you to control the AV receiver while you’re in Zone 2/3/4, or control it when it’s out of sight, for example, installed in a cabinet. A commercially available IR emitter can be con- nected to the IR OUT jack to pass IR (infrared) remote control signals through to other components. c Digital OPTICAL IN 1 and 2 (DTR-70.1) Digital OPTICAL IN 1, 2, and 3 (DTR-80.1) These optical digital audio inputs are for connecting components with optical digital audio outputs, such as CD and DVD/BD players. They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Digital Audio Input Setup” on page 53. d Digital COAXIAL IN 1, 2, and 3 These coaxial digital audio inputs are for connect- ing components with coaxial digital audio outputs, such as CD and DVD/BD players. They’re assign- able, which means you can assign each one to an input selector to suit your setup. See “Digital Audio Input Setup” on page 53. e USB port (DTR-80.1) A USB mass storage device, such as a USB flash drive or MP3 player, containing music files can be plugged in here and the music selected can be played through the AV receiver. f ETHERNET This port is for connecting the AV receiver to your Ethernet network (e.g., router or switch) for playing music files on a networked computer or media server, or for listening to Internet radio. g u REMOTE CONTROL This u (Remote Interactive) jack can be con- nected to an u jack on another Integra/Onkyo AV component. The AV receiver’s remote controller can then be used to control that component. To use u, you must make an analog audio connection (RCA) between the AV receiver and the other AV compo- nent, even if they are connected digitally. h RS232 Terminal for control. i HDMI IN 1–6, OUT MAIN, and OUT SUB (DTR-70.1) HDMI IN 1–7, OUT MAIN, and OUT SUB (DTR-80.1) HDMI (High Definition Multimedia Interface) con- nections carry digital audio and digital video. The HDMI inputs are for connecting components with an HDMI output, such as a DVD player, Blu- ray Disc Player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “HDMI Input Setup” on page 51. The HDMI outputs are for connecting a TV or pro- jector with an HDMI input. Rear Panel d k e l p n m q o b h g i j a c f r s w B C D E t x u v z y A F* * North American models (DTR-80.1)

j MONITOR OUT These S-Video and composite video jacks should be connected to a video input on your TV or projector. k COMPONENT VIDEO IN 1, 2 and 3 These RCA component video inputs are for con- necting components with a component video out- put, such as a DVD player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Component Video Input Setup” on page 52. l COMPONENT VIDEO MONITOR OUT These RCA component video outputs are for con- necting a TV or projector with a component video input. m COMPONENT VIDEO ZONE 2 OUT This RCA component video output is for connect- ing a TV or projector with a component video input located in your main listening room or Zone 2. n ZONE 2 OUT This composite video output can be connected to a video input on a TV in Zone 2. o PC INPUT ANALOG RGB (DTR-80.1) This input terminal is for connecting a personal computer with an analog RGB output. You can assign it to an input selector to suit your setup. See “Component Video Input Setup” on page 52. p FM ANTENNA This jack is for connecting an FM antenna. AM ANTENNA These push terminals are for connecting an AM antenna. q AC INLET The supplied power cord is connected here. The other end of the power cord should be connected to a suitable wall outlet. r GND screw This screw is for connecting a turntable’s ground wire. s PHONO IN These analog audio inputs are for connecting a turn- table. t CD IN These analog audio inputs are for connecting a CD player’s analog audio output. u 12V TRIGGER OUT (A/B/C) These outputs can be connected to the 12-volt trig- ger inputs on other components. v TV/TAPE IN/OUT These analog audio inputs and outputs are for con- necting a TV or recorder with an analog audio input and output (cassette, Mini Disc, etc.). w AUX 2 IN This analog audio input is for connecting an analog audio output, such as an audio device, etc. x GAME IN Here you can connect a game console, etc. Input jacks include S-Video, composite video, and analog audio. y CBL/SAT IN Here you can connect a cable/satellite receiver, set- top box, etc. Input jacks include S-Video, composite video, and analog audio. z VCR/DVR IN/OUT Here you can connect a VCR or DVR (digital video recorder). Input and output jacks include S-Video, composite video, and analog audio. A DVD/BD IN Here you can connect a DVD/BD player. Input jacks include S-Video, composite video, and analog audio. You can connect a DVD/BD player’s 2-chan- nel analog audio output. B MULTI CH input: FRONT L/R, CENTER, SUBWOOFER, SURR L/R, and SURR BACK L/R This analog multichannel input is for connecting a component with a 5.1/7.1-channel analog audio out- put, such as a DVD player, DVD-Audio or Super Audio CD-capable player, or an MPEG decoder. C PRE OUT: FRONT L/R, CENTER, SURR L/R, SURR BACK L/R, and FRONT HIGH/WIDE L/R These multichannel analog audio outputs can be connected to the analog audio input on a multichan- nel power amplifier for when you want to use the AV receiver solely as a preamplifier. PRE OUT: SW1, SW2 These analog audio outputs can be connected to a powered subwoofer. You can connect the powered subwoofer with each jacks respectively. Level and distance can be set individually for each output. D PRE OUT: ZONE 2, ZONE 3 These analog audio outputs can be connected to the line inputs on amplifiers in Zone 2 and Zone 3. The SW jacks can be connected to the inputs on pow- ered subwoofers in Zone 2 and Zone 3.

E FRONT L/R, CENTER, SURR/ZONE 4 L/R, SURR BACK/ZONE 3 L/R, FRONT HIGH L/R, and FRONT WIDE/ZONE 2 L/R These terminal posts are for connecting the front L/R, center, surround/zone 4 L/R, surround back/zone 3 L/R, front high L/R, and front wide/zone 2 L/R speakers. The FRONT L/R and SURR BACK/ZONE 3 L/R terminal posts can be used with front speakers and surround back speakers respectively, or used to bi- amp or bridge the front speakers. See “Bi-amping the Front Speakers” on page 21 and “Bridging the Front Speakers” on page 22. The FRONT WIDE/ZONE 2 L/R terminals can be used with front wide speakers or zone 2 speakers respectively, or used to connect the passive sub- woofers. See “Connecting Zone 2” on page 137. The SURR BACK/ZONE 3 L/R terminals can be used with surround back speakers respectively, or used to connect the speakers in Zone 3. See “Connecting Zone 3” on page 139. The SURR/ZONE 4 L/R terminals can be used with surround speakers respectively, or used to connect the speakers in Zone 4. See “Connecting Zone 4” on page 140. F SIRIUS antenna (North American models) This jack is for connecting a SIRIUS Satellite Radio antenna, sold separately (see the separate SIRIUS instructions). See pages 18 to 44 for connection information.

replacing the batteries. • Don’t mix new and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion. • Expired batteries should be removed as soon as possi- ble to prevent damage from leakage or corrosion. To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below. Transmission Received Notes: • The remote controller may not work reliably if the AV receiver is subjected to bright light, such as direct sun- light or inverter-type fluorescent lights. Keep this in mind when installing. • If another remote controller of the same type is used in the same room, or the AV receiver is installed close to equipment that uses infrared rays, the remote control- ler may not work reliably. • Don’t put anything, such as a book, on the remote con- troller, because the buttons may be pressed inadvert- ently, thereby draining the batteries. • The remote controller may not work reliably if the AV receiver is installed in a rack behind colored glass doors. Keep this in mind when installing. • The remote controller will not work if there’s an obstacle between it and the AV receiver’s remote con- trol sensor. • When the remote control codes have been registered and you want to operate another component (page 150), or when you want to operate an Inte- gra/Onkyo component without u connection, point the remote controller at the other component to use it. • When you want to operate an Integra/Onkyo compo- nent with u connection or an -compatible component connected via HDMI (pages 152 and 153), point the remote controller at the AV receiver’s remote control sensor. Installing the Batteries 1 To open the battery compartment, press the small lever and remove the cover. 2 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. 3 Replace the cover and push it shut. Aiming the Remote Controller Remote control sensor AV receiver Approx. 16 ft. (5 m) 30° off center (Left/Right/Up/Down) 15 15 Transmitter AV receiver Approx. 16 ft. (5 m) Incoming sensor 15° off center (Left/Right/Up/Down)

a Standby button (45) Sets the AV receiver to Standby. b On button (45) Turns on the AV receiver. c Activities buttons (67, 162) Used with the MACRO function. d Remote Mode/Input Selector buttons (64, 152 to 158) Selects the remote controller modes and the input sources. e SP Layout button (66) This button is used to change the speaker selection: Front High speakers or Front Wide speakers*2. *2 If you use surround back speakers, you can select the combina- tion of surround back and front high, or surround back and front wide speakers. f Arrow [q]/[w]/[e]/[r] and Enter buttons Used to select and adjust settings. g Setup button Used to change settings. h Listening Mode buttons (88) Used to select the listening modes. i Dimmer button (66) Adjusts the display brightness. j Display button (65) Displays information about the current input source. k Muting button (66) Mutes or unmutes the AV receiver. l VOL [q]/[w] button (64) Adjusts the volume of the AV receiver regardless of the currently selected remote controller mode. m Video button (46, 50, 111) Used to change video settings. n Return button Returns to the previous display when changing set- tings. o Audio button (123) Used to change audio settings. When the “Audio TV Out” setting is set to “On” (page 119), this button is disabled. p Sleep button (66) Used with the Sleep function. Controlling the AV Receiver To control the AV receiver, press the [Receiver] but- ton to select Receiver mode. You can also use the remote controller to control your DVD/BD player, CD player, and other components. See pages 148 to 162 for more details. d c *1 b a g 1f e h 2i 5 p j3 4 l k m n o *1 When you want to change the remote controller mode without changing the current input source, press the [Mode] button and within about eight seconds, press the Remote Mode button. Then, with the AV receiver’s remote controller, you can control the component corresponding to the button you pressed.

To control the AV receiver’s tuner, press the [Tuner] (or [Receiver]) button. You can select AM or FM by pressing the [Tuner] button repeatedly. 1 Arrow [q]/[w] buttons Used to tune into radio stations. 2 D.TUN button (69) (Tuner remote mode only) Selects the Direct tuning mode. 3 Display button Displays information about the band, frequency, preset number, and so on. 4 CH +/– button (70) Used to select radio presets. 5 Number buttons (69, 70) Used to select radio stations directly in the Direct tuning mode. Also you can select a preset directly. Note: An Onkyo cassette recorder connected via u can also be controlled in Receiver mode (see page 158).

Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes. You can also enjoy THX Surround EX (THX-certified THX speaker system recommended). Enjoying Home Theater Front left and right speakers These output the overall sound. Their role in a home theater is to provide a solid anchor for the sound image. They should be positioned facing the listener at about ear level, and equidistant from the TV. Angle them inward so as to create a triangle, with the listener at the apex. Center speaker This speaker enhances the front left and right speakers, making sound movements dis- tinct and providing a full sound image. In movies it’s used mainly for dialog. Position it close to your TV fac- ing forward at about ear level, or at the same height as the front left and right speakers. Subwoofer The subwoofer handles the bass sounds of the LFE (Low-Frequency Effects) channel. The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listening posi- tion. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at one-third the width of the wall, as shown. Tip: To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results. Surround left and right speakers These speakers are used for precise sound positioning and to add realistic ambience. Position them at the sides of the listener, or slightly behind, about 2 to 3 feet (60 to 100 cm) above ear level. Ideally they should be equidis- tant from the listener. Surround back left and right speakers These speakers are necessary to enjoy Dolby Digital EX, DTS-ES Matrix, DTS-ES Discrete, THX Surround EX, etc. They enhance the realism of surround sound and improve sound localization behind the listener. Position them behind the listener about 2 to 3 feet (60 to 100 cm) above ear level. Front high left and right speakers These speakers are necessary to enjoy Dolby Pro Logic IIz Height, and Audyssey Dynamic Surround Expansion™. They significantly enhance the spatial experience. Position them at least 3.3 feet (100 cm) above the front left and right speakers (preferably as high as possible) and at an angle slightly wider than the front left and right speakers. Corner position 1/3 of wall position Front wide left and right speakers These speakers are necessary to enjoy Audyssey Dynamic Surround Expansion™ (DSX). They significantly enhance the spatial experience. Position them well outside of the front left and right speakers. See also http://www.audyssey.com/technology/dsx.html about optimum speaker placement for Audyssey Dynamic Surround Expansion™.

Speaker Configuration For 9.2-channel surround-sound playback, you need nine speakers and two powered subwoofers. The following table indicates the channels you should use depending on the number of speakers that you have. * If you’re using only one surround back speaker, connect it to the SURR BACK/ZONE 3 L terminal. No matter how many speakers you use, two powered subwoofers are recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to set the speaker settings. You can do this automatically (see page 58) or manually (see page 102). Note: Front high and front wide speakers produce no sound at the same time. Attaching the Speaker Labels The AV receiver’s positive (+) speaker terminals are all red (the negative (–) speaker terminals are all black). The supplied speaker cable labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the above table. Then all you need to do is to match the color of each label to the corresponding speaker terminal. • If you are using banana plugs, tighten the speaker ter- minal before inserting the banana plug. • Do not insert the speaker code directly into the center hole of the speaker terminal. Connecting Powered Subwoofers Using a suitable cable, connect the AV receiver’s PRE OUT: SW1, SW2 to an input on your powered sub- woofer, as shown. If your subwoofer is unpowered and you’re using an external amplifier, connect the PRE OUT: SW1, SW2 to an input on the amp. You can connect the powered subwoofer with each jacks respectively. Level and distance can be set individually for each output. If you use one subwoofer, connect it to PRE OUT: SW1. Connecting Your Speakers Number of speakers: 2 3 4 5 6 7 7 7 8 8 9 9 9 10 11 Front left ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Front right ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Center ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Surround left ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Surround right ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Surround back* ✓ ✓ ✓ ✓ Surround back left ✓ ✓ ✓ ✓ Surround back right ✓ ✓ ✓ ✓ Front high left ✓ ✓ ✓ ✓ ✓ ✓ Front high right ✓ ✓ ✓ ✓ ✓ ✓ Front wide left ✓ ✓ ✓ ✓ ✓ ✓ Front wide right ✓ ✓ ✓ ✓ ✓ ✓ Speaker Color Front left White Front right Red Center Green Surround left, Zone 4 left Blue Surround right, Zone 4 right Gray Surround back left, Zone 3 left Brown Surround back right, Zone 3 right Tan Front high left White Front high right Red Front wide left, Zone 2 left White Front wide right, Zone 2 right Red LINE INPUT LINE INPUT LINE INPUT LINE INPUT Powered subwoofer

Using Dipole Speakers You can use dipole speakers for the surround left and right, surround back left and right speakers. Dipole speakers output the same sound in two directions. Dipole speakers typically have an arrow printed on them to indicate how they should be positioned. The surround left and right dipole speakers should be positioned so that their arrows point toward the TV/screen, while the surround back left and right and front high left and right and front wide left and right dipole speakers should be positioned so that their arrows point toward each other, as shown. Speaker Connection Precautions Read the following before connecting your speakers: • You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, be sure to set the minimum speaker impedance to “4ohms” (see page 54). If you use speakers with a lower impedance, and use the amplifier at high vol- ume levels for a long period of time, the built-in pro- tection circuit may be activated. • Disconnect the power cord from the wall outlet before making any connections. • Read the instructions supplied with your speakers. • Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+) terminals, and negative (–) terminals only to nega- tive (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural. • Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided. • If you use 4 or 5 speakers, connect each of the two surround speakers to the SURR/ZONE 4 L/R termi- nals. Do not connect them to the SURR BACK/ZONE 3 L/R, FRONT WIDE/ZONE 2 L/R, or FRONT HIGH L/R terminals. • Be careful not to short the positive and negative wires. Doing so may damage the AV receiver. • Make sure the metal core of the wire does not have contact with the AV receiver’s rear panel. Doing so may damage the AV receiver. • Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver. • Don’t connect one speaker to several terminals. 1 1 5 6 7 8 2 3 4 5 7 8 6 1 9 10 11 12 2 3 4 9 10 11 12 1 TV/screen TV/screen 1. Subwoofers 2. Front left speaker 3. Center speaker 4. Front right speaker 5. Surround left speaker 6. Surround right speaker 7. Surround back left speaker 8. Surround back right speaker 9. Front high left speaker 10.Front high right speaker 11.Front wide left speaker 12.Front wide right speaker Dipole speakers Normal speakers

Connecting the Speaker Cables The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one surround back speaker, connect it to the SURR BACK/ZONE 3 L terminal. 1 Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown. 2 Unscrew the terminal. 1/2" to 5/8" (12 to 15 mm) 3 Fully insert the bare wires. 4 Screw the terminal tight. Surround back left speaker Surround back right speaker Surround left speaker Surround right speaker Front high left speaker Front high right speaker Front left speaker Front right speaker Center speaker Front wide right speaker Front wide left speaker

The FRONT L/R and SURR BACK/ZONE 3 L/R termi- nal posts can be used with front speakers and surround back speakers respectively, or bi-amped to provide sepa- rate tweeter and woofer feeds for a pair of front speakers that support bi-amping, providing improved bass and treble performance. • When bi-amping is used, surround back speakers can- not be used. • For bi-amping, the FRONT L/R terminal posts con- nect to the front speakers’ woofer terminals. And the SURR BACK/ZONE 3 L/R terminal posts connect to the front speakers’ tweeter terminals. • Once you’ve completed the bi-amping connections shown below and turned on the AV receiver, you must set the “Speakers Type(Front)” setting to “Bi-Amp” to enable biamping (see page 54). Important: • When making the bi-amping connections, be sure to remove the jumper bars that link the Speakers’ tweeter (high) and woofer (low) terminals. • Bi-amping can only be used with speakers that support bi-amping. Refer to your speaker manual. Bi-amping Speaker Hookup Bi-amping the Front Speakers 1 Connect the AV receiver’s FRONT R positive (+) terminal to the right speaker’s positive (+) Woofer (low) terminal. And connect the AV receiver’s FRONT R negative (–) terminal to the right speaker’s negative (–) Woofer (low) terminal. 2 Connect the AV receiver’s SURR BACK/ZONE 3 R positive (+) terminal to the right speaker’s pos- itive (+) Tweeter (high) terminal. And connect the AV receiver’s SURR BACK/ZONE 3 R negative (–) terminal to the right speaker’s negative (–) Tweeter (high) terminal. 3 Connect the AV receiver’s FRONT L positive (+) terminal to the left speaker’s positive (+) Woofer (low) terminal. And connect the AV receiver’s FRONT L negative (–) terminal to the left speaker’s negative (–) Woofer (low) terminal. 4 Connect the AV receiver’s SURR BACK/ZONE 3 L positive (+) terminal to the left speaker’s posi- tive (+) Tweeter (high) terminal. And connect the AV receiver’s SURR BACK/ZONE 3 L negative (–) terminal to the left speaker’s negative (–) Tweeter (high) terminal. Woofer (low) Tweeter (high) Tweeter (high) Woofer (low) Left speaker Right speaker

The FRONT L/R and SURR BACK/ZONE 3 L/R ter- minal posts can be used with front speakers and surround back speakers respectively, or bridged together to pro- vide almost double the output power for the front speakers. • When bridging is used, surround back speakers cannot be used. • For bridging, the positive (+) FRONT L/R and SURR BACK/ZONE 3 L/R terminal posts are used, but the negative (–) FRONT L/R and SURR BACK/ZONE 3 L/R terminals are not. • Once you’ve completed the bridging connections shown below and turned on the AV receiver, you must set the “Speakers Type(Front)” setting to “BTL” to enable bridging (see page 54). Notes: • Use only front speakers with an impedance of 8 ohms or higher for bridging. Failure to do so may seriously damage the AV receiver. • When using bridging, make sure that your front speak- ers can handle the additional power. Bridged Speaker Hookup Bridging the Front Speakers 1 Connect the AV receiver’s FRONT R positive (+) terminal to the right speaker’s positive (+) ter- minal. And connect the AV receiver’s SURR BACK/ZONE 3 R positive (+) terminal to the right speaker’s negative (–) terminal. 2 Connect the AV receiver’s FRONT L positive (+) terminal to the left speaker’s positive (+) terminal. And connect the AV receiver’s SURR BACK/ZONE 3 L positive (+) terminal to the left speaker’s negative (–) terminal. Right speaker Left speaker

The FRONT WIDE/ZONE 2 L/R terminal posts can be used with front wide speakers or passive subwoofers. • Once you’ve connected the passive subwoofers shown below and turned on the AV receiver, you must set the “Passive Subwoofer” setting to “Use” (see page 54). • When the passive subwoofers are used, the Powered Zone2/4 cannot be used. • If you use one passive subwoofer, connect it to the SUBWOOFER1 terminals. Connecting Passive Subwoofers Subwoofer 1 Subwoofer 2

This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner. Connecting the Indoor FM Antenna The supplied indoor FM antenna is for indoor use only. If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out- door FM antenna instead (see page 25). Connecting the AM Loop Antenna The supplied indoor AM loop antenna is for indoor use only. If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commer- cially available outdoor AM antenna (see page 25). Connecting Antenna 1 Attach the FM antenna, as shown. (North American models) (Australian models) Once your AV receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception. 2 Use thumbtacks or something similar to fix the FM antenna into position. Caution: Be careful that you don’t injure yourself when using thumbtacks. FM ANTENNA jack AM ANTENNA push terminals Insert the plug fully into the jack. Insert the plug fully into the jack. Thumbtacks, etc. 1 Assemble the AM loop antenna, inserting the tabs into the base, as shown. 2 Connect both wires of the AM loop antenna to the AM antenna push termi- nals, as shown. (The antenna’s wires are not polarity sensitive, so they can be connected either way around.) Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation. Once your AV receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception. Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords. Push Insert wire Release

Connecting an Outdoor FM Antenna If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft. • For best results, install the outdoor FM antenna well away from tall buildings, preferably with a clear line of sight to your local FM transmitter. • Outdoor antenna should be located away from possi- ble noise sources, such as neon signs, busy roads, etc. • For safety reasons, outdoor antenna should be situated well away from power lines and other high-voltage equipment. • Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock haz- ards. ■Using a TV/FM Antenna Splitter It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If cir- cumstances demand it, use a TV/FM antenna splitter, as shown. Connecting an Outdoor AM Antenna If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown. Outdoor AM antennas work best when installed outside horizontally, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the outdoor antenna should be right connected. Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards. To AV receiver To TV (or VCR) TV/FM antenna splitter Outdoor antenna Insulated antenna cable AM loop antenna

• Before making any AV connections, read the manuals supplied with your other AV components. • Don’t connect the power cord until you’ve completed and double-checked all AV connections. Optical Digital Jacks The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way. Caution: To prevent shutter damage, hold the optical plug straight when inserting and removing. AV Connection Color Coding RCA-type AV connections are usually color-coded: red, white, and yellow. Use red plugs to connect right-chan- nel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and out- puts (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs. • Push plugs in all the way to make good connections (loose connec- tions can cause noise or malfunc- tions). • To prevent interference, keep audio and video cables away from power cords and speaker cables. AV Cables & Jacks The AV receiver does not support SCART plugs. About AV Connections Analog audio Composite video Left (white) Right (red) Right (red) Left (white) (Yellow) (Yellow) Right! Wrong! Video / Audio Cable Jack Description HDMI HDMI connections can carry uncompressed stan- dard- or high-definition digital video and audio and offer the best picture and sound quality. Video Component video cable Component video separates the luminance (Y) and color difference signals (PR, PB), providing the best picture quality (some TV manufacturers label their component video sockets slightly differently). S-Video cable S-Video separates the luminance and color signals and provides better picture quality than composite video. Composite video cable Composite video is commonly used on TVs, VCRs, and other video equipment. Audio Optical digital audio cable Offers the best sound quality and allows you to enjoy surround sound (e.g., Dolby Digital, DTS). The audio quality is the same as for coaxial. Coaxial digital audio cable Offers the best sound quality and allows you to enjoy surround sound (e.g., Dolby Digital, DTS). The audio quality is the same as for optical. Analog audio cable (RCA) This cable carries analog audio. It’s the most com- mon connection format for analog audio, and can be found on virtually all AV components. Multichannel analog audio cable (RCA) This cable carries multichannel analog audio and is typically used to connect DVD players with a 7.1- channel analog audio output. Several standard ana- log audio cables can be used instead of a multichan- nel cable. HDMI Y PB/CB PR/CR Y PB/CB PR/CR V OPTICAL L R

About HDMI Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, DVD/BD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichannel digital audio, and multichannel PCM). The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface)*1, so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and displays, resulting in no picture.) The AV receiver uses HDCP (High-bandwidth Digital Content Protection)*2, so only HDCP-compatible components can display the picture. Supported Audio Formats • 2-channel linear PCM (32–192 kHz, 16/20/24 bit) • Multichannel linear PCM (up to 7.1 ch, 32–192 kHz, 16/20/24 bit) • Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS Express, DTS-HD High Resolution Audio, DTS-HD Master Audio) Your DVD/BD players must also support HDMI output of the above audio formats. ■Integra/Onkyo for System Control , which stands for Remote Interactive over HDMI, is the name of the system control function found on Inte- gra/Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than -compatible components cannot be guaranteed. • Set “HDMI Control (RIHD)” to “On” (page 120). • See “Controlling a TV” (page 152) and “Controlling a DVD Player or DVD Recorder” (page 153) for operation. Notes: • Do not connect the -compatible component more than the following number to the HDMI input terminal so that the linked operations work properly. a. DVD/BD player is up to three. b. DVD/BD recorder is up to three. c. Cable/Satellite Set-top box is up to four. • Do not connect the AV receiver to the other AV receiver /AV amplifier via HDMI. • When the -compatible component more than the above-mentioned is connected, the linked operations are not guaranteed. • The control does not support HDMI OUT SUB. Use HDMI OUT MAIN instead. About Copyright Protection The AV receiver supports HDCP (High-bandwidth Digital Content Protection)*2, a copy-protection system for digital video signals. Other devices connected to the AV receiver via HDMI must also support HDCP. *1 DVI (Digital Visual Interface): The digital display interface standard set by the DDWG*3 in 1999. *2 HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s designed to protect video content and requires a HDCP-compatible device to display the encrypted video. *3 DDWG (Digital Display Working Group): Lead by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open industry group’s objective is to address the industry’s requirements for a digital connectivity specification for high-performance PCs and digital displays. Connecting Components with HDMI The AV receiver’s HDMI interface is based on the following standard: x.v.Color, Deep Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD, Dolby Digital Plus, DSD, and Multichannel PCM

Making HDMI Connections ■Video Signals Digital video signals received by the HDMI IN jacks are normally output by the HDMI MAIN OUT and SUB OUT for display on your TV. Composite video, S-Video, and component video sources can be upconverted for the HDMI output. See “Video Connection Formats” on page 29 for more information. ■Audio Signals Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV receiver. Normally, they are not output by the HDMI outputs, unless the “Audio TV Out” setting is set to “On” (see page 119). To listen to audio received by the HDMI IN jacks through your TV’s speakers: •Set the “TV Control” setting to “On” (see page 120) for an -compatible TV. •Set the “Audio TV Out” setting to “On” (see page 119) when the TV is not compatible with or the “TV Control” setting to “Off”. •Set your DVD/BD player’s HDMI audio output setting to PCM. Notes: • The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not guaranteed. • When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut off. • When the “Audio TV Out” setting is set to “On” (see page 119) to hear from your TV’s speakers, by controlling the AV receiver’s volume, the sound will be output from the AV receiver’s speakers, too. When the “TV Control” setting is set to “On” to hear from speakers of -compatible TV, by controlling the AV receiver’s volume, the AV receiver’s speakers will produce sound while the TV’s speakers are muted. To stop the AV receiver’s speakers pro- ducing sound, change the settings, change your TV’s settings, or turn down the AV receiver’s volume. • The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected component’s instruction manual for details. Step 1: Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible DVD/BD player, TV, projec- tor, and so on. Step 2: Assign each HDMI IN to an input selector in the HDMI Input Setup (see page 51). Hint! HDMI IN HDMI OUT TV DVD/BD player HD camcorder, etc

By connecting both the audio and video outputs of your DVD/BD player and other AV components to the AV receiver, you can select both the audio and video simultaneously simply by selecting the appropriate input source on the AV receiver. The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your other components. Use the following sections as a guide. Video Connection Formats Video equipment can be connected to the AV receiver by using any one of the following video connection formats: composite video, S-Video, component video, or HDMI, the latter offering the best picture quality. The AV receiver can upconvert and downconvert between video formats, depending on the “Monitor Out” setting, which generally determines whether video signals are upconverted for the component video output or the HDMI output. For optimal video performance, THX recommends that video signals pass through the system without upconver- sion (e.g., component video input through to component video output). It is also recommended that you press the [VCR/DVR] and [Return] buttons on the AV receiver at the same time. Select “Skip” in the “VideoProcessor” setting by pressing the [Return] button repeatedly on the display. To reset back to the original setting, press the same button at the same time. ■“Monitor Out” Setting Set to “HDMI Main” or “HDMI Sub” With the “Monitor Out” setting set to “HDMI Main” or “HDMI Sub” (see page 49), video input signals flow through the AV receiver as shown, with composite video, S-Video, and component video sources all being upconverted for the HDMI output. Use the “HDMI Main” or “HDMI Sub” setting if you connect the AV receiver’s HDMI OUT MAIN or HDMI OUT SUB, respectively, to your TV. The composite video, S-Video, and component video outputs pass through their respective input signals as they are. Note: If not connected to the same output you have selected in the “Monitor Out” setting, the “Mon- itor Out” setting will be automatically switched to “Analog” (see page 49). In this case, the set- ting of the output resolution will be that for HDMI output (see page 49). However, it will be switched to “1080i” when “1080p” is selected, and to “Through” when “Auto” is selected. Connecting Both Audio & Video : Signal Flow Video Audio Video Audio Speakers (see pages 18 to 20 for connection information) DVD/BD player, etc. TV, projector, etc. Which Connections Should I Use? IN MONITOR OUT DVD/BD player, etc. AV receiver TV, projector, etc. Composite Composite S-Video S-Video Component Component Video Signal Flow Chart HDMI HDMI

■“Monitor Out” Setting Set to “Both”, “Both(Main)” or “Both(Sub)” With the “Monitor Out” setting set to “Both”, “Both(Main)” or “Both(Sub)” (see page 49), video input signals flow through the AV receiver as shown, with composite video, S-Video, and component video sources all being upconverted for both HDMI outputs. Use the “Both”, “Both(Main)” or “Both(Sub)” setting if you connect the AV receiver’s HDMI OUT MAIN and HDMI OUT SUB to your TVs. The composite video, S-Video, and component video outputs pass through their respective input signals as they are. Both: Video signals are output from both HDMI outputs at the resolution supported by both TVs. You cannot select “Resolution” setting. The pic- ture adjust setting will be that for “HDMI Main”. Both (Main): Video signals are output from both HDMI outputs but HDMI OUT MAIN will become a priority; depending on the resolution, video signals may not be output from HDMI OUT SUB. Both (Sub): Video signals are output from both HDMI outputs but HDMI OUT SUB will become a priority; depending on the resolution, video signals may not be output from HDMI OUT MAIN. Note: The “Monitor Out” setting will be automatically switched to “Analog” (see page 49) if not connected to both outputs when “Both” is selected or if not connected to a priority output when “Both(Main)” or “Both(Sub)” is selected. ■“Monitor Out” Setting Set to “Analog” With the “Monitor Out” setting set to “Analog” (see page 49), video input signals flow through the AV receiver as shown, with composite video and S-Video sources being upconverted for the component video output. Use this setting if you connect the AV receiver’s COMPONENT VIDEO MONITOR OUT to your TV. Composite video is upconverted to S-Video and S-Video is downconverted to composite video. Note that these conversions only apply to the MONITOR OUT V and S outputs, not the VCR/DVR OUT V and S outputs. The composite video, S-Video, and component video outputs pass through their respective input signals as they are. This signal flow also applies when the “Resolu- tion” setting is set to “Through” (see page 49). Video Signal Flow and the Resolution Setting When the “Monitor Out” setting is set to “Ana- log” (see page 49), if the “Resolution” setting is set to anything other than “Through” (see page 49), the video signal flow will be as shown here, with composite video and S-Video sources being upconverted for the component video out- put. The composite video, S-Video, and component video outputs pass through their respective ana- log input signals as they are. HDMI input signals are not output. IN MONITOR OUT DVD/BD player, etc. AV receiver TV, projector, etc. Composite Composite S-Video S-Video Component Component Video Signal Flow Chart HDMI HDMI IN MONITOR OUT DVD/BD player, etc. AV receiver TV, projector, etc. Composite Composite S-Video S-Video Component Component Video Signal Flow Chart HDMI HDMI IN MONITOR OUT DVD/BD player, etc. AV receiver TV, projector, etc. Composite Composite S-Video S-Video Component Component Video Signal Flow Chart HDMI HDMI

Audio Connection Formats Audio equipment can be connected to the AV receiver by using any of the following audio con- nection formats: analog, optical, coaxial, analog multichannel, or HDMI. When choosing a connection format, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice versa. For example, audio signals connected to an optical or coaxial digital input are not output by the analog TV/TAPE OUT. If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: HDMI, digital, analog. *1 DVD/BD player, etc. AV receiver TV, projector, etc. Audio Signal Flow Chart HDMI Analog *1 Depends on the “Audio TV Out” setting (see page 119). *2 Only the front L/R channels are output. Optical Coaxial Multichannel Analog HDMI

See “Connecting Components with HDMI” on page 27 for HDMI connection information. • With connection , you can listen to and record audio from your TV or listen in Zone 2, Zone 3 or Zone 4. • To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2, Zone 3 or Zone 4 as well, use and , or and .) If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite receiver to the AV receiver and use its tuner to listen to TV programs through the AV receiver (see pages 35 and 37). Connecting a TV or Projector Connection AV receiver Signal flow TV, projector, etc. COMPONENT VIDEO MONITOR OUT ⇒ Component video input MONITOR OUT S ⇒ S-Video input MONITOR OUT V ⇒ Composite video input TV/TAPE IN L/R ⇐ Analog audio L/R output DIGITAL COAXIAL IN 2 (VCR/DVR) ⇐ Digital coaxial output DIGITAL OPTICAL IN 1 (GAME) (DTR-70.1) DIGITAL OPTICAL IN 2 (TV/TAPE) (DTR-80.1) ⇐ Digital optical output Step 1: Video Connection Choose a video connection that matches your TV ( , , or ), and then make the connection. A B C Step 2: Audio Connection Choose an audio connection that matches your TV ( , , or ), and then make the connection. a b c a b c a b a c A B C a b c COAXIAL OUT OPTICAL OUT AUDIO OUT L R S VIDEO IN VIDEO IN COMPONENT VIDEO IN Y PB PR a A C B b c TV, projector, etc. When you use connection , you need to assign the digital audio input (see page 53). b (DTR-70.1) When you use connection , you need to assign the digital audio input (see page 53). c Hint!

See “Connecting Components with HDMI” on page 27 for HDMI connection information. • With connection , you can listen to and record audio from your DVD player or listen in Zone 2, Zone 3 or Zone 4. • To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2, Zone 3 or Zone 4 as well, use and , or and .) • If your DVD player has main left and right outputs and multichannel left and right outputs, be sure to use the main left and right outputs for connection . Connecting a DVD Player Connection AV receiver Signal flow DVD player COMPONENT VIDEO IN 1 (DVD/BD) ⇐ Component video output DVD/BD IN S ⇐ S-Video output DVD/BD IN V ⇐ Composite video output DVD/BD IN L/R ⇐ Analog audio L/R output DIGITAL COAXIAL IN 1 (DVD/BD) ⇐ Digital coaxial output DIGITAL OPTICAL IN 1 (GAME) ⇐ Digital optical output Step 1: Video Connection Choose a video connection that matches your DVD player ( , , or ), and then make the connection. You must connect the AV receiver to your TV via the same type of connection. A B C Step 2: Audio Connection Choose an audio connection that matches your DVD player ( , , or ), and then make the connection. a b c a b c a b a c a A B C a b c COAXIAL OUT OPTICAL OUT AUDIO OUT L R S VIDEO OUT VIDEO OUT COMPONENT VIDEO OUT Y PB PR a C B b c A DVD player When you use connection , you need to assign the digital audio input (see page 53). c

Hooking Up the Multichannel Input If your DVD player supports multichannel audio formats such as DVD-Audio and Super Audio CD, and it has a multi- channel analog audio output, you can connect it to the AV receiver’s multichannel input. Use a multichannel analog audio cable, or several normal audio cables, to connect the AV receiver’s MULTI CH: FRONT L/R, CENTER, SURR L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.1-channel analog audio output on your DVD player. If your DVD player has a 5.1-channel analog audio output, don’t connect anything to the AV receiver’s SURR BACK L/R jacks. Before using the multichannel input, you must assign it to an input selector. See “Analog Audio Input Setup” on page 54. To select the multichannel input, see “Audio Selector” on page 125. To adjust the subwoofer sensitivity for the multi- channel input, see “Subwoofer Input Sensitivity” on page 101. 5.1 ch 7.1 ch CENTER SURROUND L R SURR BACK L R FRONT R L SUB WOOFER DVD player

With this hookup, you can use your VCR’s tuner to listen to your favorite TV programs via the AV receiver, useful if your TV has no audio outputs. • With connection , you can listen to the VCR or DVD recorder in Zone 2, Zone 3 or Zone 4. • To enjoy Dolby Digital and DTS, use connection or . (To listen in Zone 2, Zone 3 or Zone 4 as well, use and , or and .) . Connecting a VCR or DVD Recorder for Playback Connection AV receiver Signal flow VCR or DVD recorder COMPONENT VIDEO IN 2 (CBL/SAT) ⇐ Component video output VCR/DVR IN S ⇐ S-Video output VCR/DVR IN V ⇐ Composite video output VCR/DVR IN L/R ⇐ Analog audio L/R output DIGITAL COAXIAL IN 2 (VCR/DVR) ⇐ Digital coaxial output DIGITAL OPTICAL IN 1 (GAME) ⇐ Digital optical output Hint! Step 1: Video Connection Choose a video connection that matches your VCR or DVD recorder ( , , or ), and then make the connection. You must connect the AV receiver to your TV via the same type of connection. A B C Step 2: Audio Connection Choose an audio connection that matches your VCR or DVD recorder ( , , or ), and then make the connection. a b c a b c a b a c A B C a b c COAXIAL OUT OPTICAL OUT AUDIO OUT L R S VIDEO OUT VIDEO OUT COMPONENT VIDEO OUT Y PB PR B a C b c A VCR or DVD recorder When you use connection , you need to assign the digital audio input (see page 53). c When you use connection , you need to assign the component video input (see page 52). A

Notes: • The AV receiver must be turned on for recording. Recording is not possible while it’s in Standby mode. • If you want to record directly from your TV or playback VCR to the recording VCR without going through the AV receiver, connect the TV/VCR’s audio and video outputs directly to the recording VCR’s audio and video inputs. See the manuals supplied with your TV and VCR for details. • Video signals connected to composite video inputs can only be recorded via composite video outputs. If your TV/VCR is connected to a composite video input, the recording VCR must be connected to a composite video output. Similarly, video signals connected to S-Video inputs can only be recorded via S-Video outputs. If your TV/VCR is connected to an S-Video input, the recording VCR must be connected to an S-Video output. • Sources connected to a digital input cannot be recorded. Only analog inputs can be recorded. Connecting a VCR or DVD Recorder for Recording Connection AV receiver Signal flow VCR or DVD recorder VCR/DVR OUT S ⇒ S-Video input VCR/DVR OUT V ⇒ Composite video input VCR/DVR OUT L/R ⇒ Analog audio L/R input Step 1: Video Connection Choose a video connection that matches your VCR or DVD recorder ( or ), and then make the connection. The video source to be recorded must be connected to the AV receiver via the same type of connection. A B Step 2: Audio Connection Make the audio connection . a A B a AUDIO IN L R S VIDEO IN VIDEO IN a B A VCR or DVD recorder

With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs via the AV receiver, useful if your TV has no audio outputs. • With connection , you can listen to and record audio from the video source or listen in Zone 2, Zone 3 or Zone 4. • To enjoy Dolby Digital and DTS, use connection or . (To record or listen in Zone 2, Zone 3 or Zone 4 as well, use and , or and .) Connecting a Satellite, Cable, Terrestrial Set-top box, or Other Video Source Connection AV receiver Signal flow Video source COMPONENT VIDEO IN 2 (CBL/SAT) ⇐ Component video output CBL/SAT IN S ⇐ S-Video output CBL/SAT IN V ⇐ Composite video output CBL/SAT IN L/R ⇐ Analog audio L/R output DIGITAL COAXIAL IN 3 (CBL/SAT) ⇐ Digital coaxial output DIGITAL OPTICAL IN 1 (GAME) ⇐ Digital optical output Hint! Step 1: Video Connection Choose a video connection that matches the video source ( , , or ), and then make the connection. You must connect the AV receiver to your TV via the same type of connection. A B C Step 2: Audio Connection Choose an audio connection that matches the video source ( , , or ), and then make the connection. a b c a b c a b a c A B C a b c COAXIAL OUT OPTICAL OUT AUDIO OUT L R S VIDEO OUT VIDEO OUT COMPONENT VIDEO OUT Y PB PR B a C b c A Satellite, cable, set-top box, etc. When you use connection , you need to assign the digital audio input (see page 53). c

• With connection , you can listen to and record audio from your game console or listen in Zone 2, Zone 3 or Zone 4. • To enjoy Dolby Digital and DTS, use connection . (To record or listen in Zone 2, Zone 3 or Zone 4 as well, use and .) Connecting a Game Console Connection AV receiver Signal flow Game console COMPONENT VIDEO IN 3 (GAME) ⇐ Component video output GAME IN S ⇐ S-Video output GAME IN V ⇐ Composite video output GAME IN L/R ⇐ Analog audio L/R output DIGITAL OPTICAL IN 1 (GAME) ⇐ Digital optical output Step 1: Video Connection Choose a video connection that matches your game console ( , , or ), and then make the connection. You must connect the AV receiver to your TV with the same type of connection. A B C Step 2: Audio Connection Choose an audio connection that matches your game console ( or ), and then make the connection. a b a b a b A B C a b OPTICAL OUT AUDIO OUT L R S VIDEO OUT VIDEO OUT COMPONENT VIDEO OUT Y PB PR B a C b A Game Console

Connecting a Camcorder or Other Device Connection AV receiver Signal flow Camcorder etc. AUX1 Input Video ⇐ Composite video output AUX1 Input L-Audio-R ⇐ Analog audio L/R output AUX1 Input Digital ⇐ Digital optical output Step 1: Video Connection Make the connection . A Step 2: Audio Connection Choose an audio connection that matches your camcorder ( or ), and then make the connection. a b A a b AUDIO OUT VIDEO OUT L R Video Audio L R AUX1 Input AUX1 Input OPTICAL OUT Digital AUX1 Input A b a Camcorder etc.

■CD Player or Turntable (MM) with Built-in Phono Preamp • With connection , you can listen to and record audio from your CD player or listen in Zone 2, Zone 3 or Zone 4. • To connect the CD player digitally, use connection or . (To record or listen in Zone 2, Zone 3 or Zone 4 as well, use and , or and .) ■Turntable (MM) with no Phono Preamp Built-in The AV receiver’s PHONO IN is designed for use with a mov- ing magnet (MM) type cartridge. Use an analog audio cable to connect the AV receiver’s PHONO IN L/R jacks to the audio output on your turntable. Notes: • If your turntable has a ground wire, connect it to the AV receiver’s GND screw. With some turntables, connecting the ground wire may produce an audible hum. If this happens, disconnect it. • If your turntable has a moving coil (MC) type cartridge, you’ll need a commercially available MC head amp or MC transformer. Connect your turntable to the head amp or trans- former, and connect that to the AV receiver’s PHONO IN L/R jacks. • You can also use a phono equalizer to connect a turntable with an MC-type cartridge. See your phono equalizer’s man- ual for details. Connecting a CD Player or Turntable Connection AV receiver Signal flow CD or turntable CD IN L/R ⇐ Analog audio L/R output DIGITAL COAXIAL IN 2 (VCR/DVR) ⇐ Digital coaxial output DIGITAL OPTICAL IN 2 (CD) (DTR-70.1) DIGITAL OPTICAL IN 3 (CD) (DTR-80.1) ⇐ Digital optical output Step 1: Choose a connection that matches your CD player ( , , or ). Use connection for a turntable with a built-in phono preamp. a b c a a b c a b a c a b c IN 3 (CD) OPTICAL IN L R L R CD AUDIO OUTPUT OPTICAL OUT AUDIO OUT L R COAXIAL OUT L R IN IN 2 COAXIAL (VCR/DVR) CD a b a c Turntable (MM) with built-in phono preamp CD player When you use connection , you need to assign the digital audio input (see page 53). b L R AUDIO OUTPUT Turntable (MM) with no phono preamp built-in

• With connection , you can play and record or listen in Zone 2, Zone 3 or Zone 4. • To connect the recorder digitally for playback, use connections and , or and . Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Step 1: Choose a connection that matches the recorder ( , or ), and then make the connection. a b c a a b a c Connection AV receiver Signal flow Cassette, CDR, MD, or DAT recorder TV/TAPE IN L/R TV/TAPE OUT L/R ⇐ ⇒ Analog audio L/R output Analog audio L/R input DIGITAL COAXIAL IN 3 (CBL/SAT) ⇐ Digital coaxial output DIGITAL OPTICAL IN 1 (GAME) (DTR-70.1) DIGITAL OPTICAL IN 2 (TV/TAPE) (DTR-80.1) ⇐ Digital optical output a b c c AUDIO IN L R L R IN TV/TAPE AUDIO OUT L R L R TV/TAPE COAXIAL OUT OPTICAL OUT COAXIAL OPTICAL IN 3 (CBL/SAT) IN 2 (TV/TAPE) a a b Cassette, CDR, MD, or DAT recorder When you use connection , you need to assign the digital audio input (see page 53). b (DTR-70.1) When you use connection , you need to assign the digital audio input (see page 53). c

If you want to use a more powerful power amplifier and use the AV receiver as a preamp, connect it to the PRE OUT jacks, and connect all speakers and the subwoofer to the power amplifier. You can connect the powered subwoofer with each jacks respectively. If you use one subwoofer, connect it to PRE OUT: SW1. Connecting a Power Amplifier 2 3 4 5 6 7 8 9 1 Power amplifier Powered subwoofer See “Connecting Powered Sub- woofers” on page 18 for more information. 1. Front left speaker 2. Center speaker 3. Front right speaker 4. Surround left speaker 5. Surround right speaker 6. Surround left back speaker 7. Surround right back speaker 8. Front wide/Front high left speaker* 9 Front wide/Front high right speaker* Note: * Specify “None” for the channel that you don’t want to output in the “Speaker Configuration” (page 102).

■If Your iPod Supports Video: Connect your RI Dock’s audio output jacks to the AV receiver’s GAME IN or VCR/DVR IN L/R jacks, and connect its video output jack to the AV receiver’s GAME IN V or VCR/DVR IN V jack. (Onkyo DS- A2 hookup shown below.) ■If you have an Onkyo DS-A1 RI Dock Connect its video output jack to the AV receiver’s GAME IN S or VCR/DVR IN S jack. ■If Your iPod Doesn’t Support Video: Connect your RI Dock’s audio output jacks to the AV receiver’s TV/TAPE IN L/R jacks. (Onkyo DS- A2 hookup shown below.) Note: When UP-A1 Dock that seated iPod is connected, the power consumption on standby mode slightly increases. Connecting an RI Dock Not all iPod models output video. For information about which iPod models are supported by the RI Dock, see the RI Dock’s instruction manual. L R IN GAME V GAME L R IN IN VCR/DVR VCR/DVR V V IN Make either connection. L R IN TV/TAPE Connecting a Universal Port Option Series Notes: • Enter the appropriate remote control code before using the AV receiver’s remote controller for the first time (see page 150). • Connect the RI Dock to the AV receiver with an u cable (see page 44). • Set the RI Dock’s RI MODE switch to “HDD” or “HDD/DOCK”. • Set the AV receiver’s Input Display to “DOCK” (see page 57). • See the RI Dock’s instruction manual for more information. ex. UP-A1

With u (Remote Interactive), you can use the follow- ing special functions: ■Auto Power On/Standby When you start playback on a component connected via u, if the AV receiver is on Standby, it will auto- matically turn on and select that component as the input source. Similarly, when the AV receiver is set to Standby, all components connected via u will also go on Standby. ■Direct Change When playback is started on a component connected via u, the AV receiver automatically selects that component as the input source. ■Remote Control You can use the AV receiver’s remote controller to control your other u-capable Integra/Onkyo com- ponents, pointing the remote controller at the AV receiver’s remote control sensor instead of the com- ponent. You must enter the appropriate remote con- trol code first (see page 151). Notes: • Use only u cables for u connections. u cables are supplied with Integra/Onkyo players (DVD, CD, etc.). • Some components have two u jacks. You can con- nect either one to the AV receiver. The other jack is for connecting additional u-capable components. • Connect only Integra/Onkyo components to u jacks. Connecting other manufacturer’s components may cause a malfunction. • Some components may not support all u functions. Refer to the manuals supplied with your other Inte- gra/Onkyo components. • While Zone 2, Zone 3 or Zone 4 is on, the Auto Power On/Standby and Direct Change u functions do not work. Notes: • Before connecting the power cord, connect all of your speakers and AV components. • Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit. • Do not use a power cord other than the one supplied with the AV receiver. The supplied power cord is designed exclusively for use with the AV receiver and should not be used with any other equipment. • Never disconnect the power cord from the AV receiver while the other end is still plugged into a wall outlet. Doing so may cause an electric shock. Always discon- nect the power cord from the wall outlet first, and then the AV receiver. Connecting Integra/Onkyo u Components Step 1: Make sure that each Integra/Onkyo component is connected to the AV receiver with an analog audio cable (connection in the hookup examples) (see pages 32 to 41, 43). Step 2: Make the u connection (see illustration right). Step 3: If you’re using an MD, CDR, or RI Dock, change the Input Display (see page 57). a Connecting the Power Cord L R IN DVD/BD L R IN CD L R REMOTE CONTROL ANALOG AUDIO OUT L R ANALOG AUDIO OUT e.g., CD player e.g., DVD player Step 1: Connect the supplied power cord to the AV receiver’s AC INLET. Step 2: Plug the power cord into an AC wall outlet. To AC wall outlet

On/Standby Standby On Receiver Standby indicator Turning On and Standby On the AV receiver, press the [On/Standby] button. On the remote controller, press the [Receiver] button, followed by the [On] button. The AV receiver comes on, the display lights up, and the Standby indicator goes off. Pressing the remote controller’s [On] button again will turn on any components connected via u. To turn the AV receiver off, press the [On/Standby] button, or press the remote controller’s [Standby] button. The AV receiver will enter Standby mode. To prevent any loud surprises when you turn on the AV receiver, always turn down the volume before you turn it off. or Remote controller AV receiver Smooth Operation in a Few Easy Steps To ensure smooth operation, here’s a few easy steps to help you configure the AV receiver before you use it for the very first time. These settings only need to be made once. ■Did you connect your TV to an HDMI output or COMPONENT VIDEO MONITOR OUT? If you did, “Monitor Setup” on page 46. ■Run MultEQ XT Room Correction and Speaker Setup—this is essential! See “Audyssey MultEQ® XT Room Correction and Speaker Setup” on page 58. ■Have you connected a component to an HDMI input, component video input, or digital audio input? If you have, see “HDMI Input Setup” on page 51, “Component Video Input Setup” on page 52, or “Digital Audio Input Setup” on page 53 respectively. ■Have you connected an Integra/Onkyo MD recorder, CD recorder, or RI Dock? If you have, see “Changing the Input Display” on page 57. HDMI OUT IN TV/TAPE MD recorder, CD recorder, RI Dock

This section explains the settings that you need to make before using the AV receiver for the very first time. If you connect your TV to HDMI OUT MAIN, “Monitor Out” setting is automatically set so that the onscreen setup menus are displayed and composite video, S- Video, and component video sources are upconverted* and output. On the “Monitor Out” settings, you can select whether or not to have the video sources’ images output through the HDMI output, as well as whether to have the onscreen setup menu output through the HDMI output or through an analog output. If you connect your TV to the COMPONENT VIDEO MONITOR OUT (not the HDMI output), “Monitor Out” setting is automatically set so that the onscreen setup menus are displayed and composite video and S-Video sources are upconverted* and output. ■Change “Monitor Out” setting manually Tips: • The “Monitor Out” setting can also be set using the [Video] button on the remote controller. • This setting can also be performed by using Onscreen Setup Menu (see page 49). Notes: • See page 29 for charts showing how the “Monitor Out” and “Resolution” (see page 49) settings affect the video signal flow through the AV receiver. • You can specify the output resolution for the HDMI outputs and COMPONENT VIDEO MONITOR OUT and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported by your TV (see page 49). Monitor Setup IN OUT Composite video, S-Video, component video Composite video, S-Video, component video HDMI HDMI IN OUT Composite video, S-Video Composite video, S-Video Component video Component video 1 Press the [Monitor Out] button. The current setting is displayed. 2 Press the [Monitor Out] button repeatedly to select: Analog, HDMI Main, HDMI Sub, Both, Both(Main) or Both(Sub) For details on each item, see step 4 in the page 49. Monitor Out

In this Instruction Manual, illustrations from the onscreen menu or explanations referring to the menu will be in the same language as the Instruction Manual. The default Language setting for the onscreen menu is English. If your Instruction Manual is in a language other than English, first follow the instructions below to change the Language. This setting determines the language used for the onscreen setup menus. You can select: English, German, French, Spanish, Italian, Dutch, Swedish, or Chinese. Note: This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. Selecting the Language used for the onscreen setup menus 1 Press the [Receiver] button, fol- lowed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. 2 Use the Up and Down [q]/[w] but- tons to select “6. Miscella- neous”, and then press [Enter]. The “Miscellaneous” menu appears. Setup Receiver qwer Enter 1. Input/Output Assign 2. Speaker Setup 3. Audio Adjust 4. Source Setup 5. Listening Mode Preset 6. Miscellaneous 7. Hardware Setup 8. Remote Controller Setup 9. Lock Setup Menu 1. Volume Setup 2. OSD Setup 3. 12V Trigger A Setup 4. 12V Trigger B Setup 5. 12V Trigger C Setup 6. Miscellaneous 3 Use the Up and Down [q]/[w] but- tons to select “2. OSD Setup”, and then press [Enter]. The “OSD Setup” menu appears. (Australian models) 4 Use the Up and Down [q]/[w] but- tons to select “Language”, and then use the Left and Right [e]/ [r] buttons to select: English, Deutsch, Français, Español, Italiano, Nederlands, Svenska, 中文 5 Press the [Setup] button. The setup menu closes. 6–2. OSD Setup Immediate Display Display Position TV Format Language On Bottom Auto English

Carry out the settings for the AV receiver by using the Onscreen Setup Menu. The settings of the AV receiver can be changed using the Display. Onscreen Setup Menus and Display As each item in the Onscreen Setup Menus is selected, the selected items will be displayed one by one. Note: During Audyssey MultEQ® XT Room Correction and Speaker Setup, messages, etc., that are displayed on the TV screen will appear in the Display. Using the Onscreen Setup Menus 1 Press the [Receiver] button fol- lowed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. Tip: On several functions, the explanation will be displayed under the screen. 2 Use the Up and Down [q]/[w] but- tons to select item and then press [Enter]. The submenu appears. Press the [Setup] button to close the menu. Press the [Return] button to return to the previous menu. Setup Receiver qwer Enter 1. Input/Output Assign 2. Speaker Setup 3. Audio Adjust 4. Source Setup 5. Listening Mode Preset 6. Miscellaneous 7. Hardware Setup 8. Remote Controller Setup 9. Lock Setup Menu Using the Display to change the settings 1 Press the [Receiver] button fol- lowed by the [Setup] button. The main menu item appears on the display. 2 Use the Up and Down [q]/[w] but- tons to select item and then press [Enter]. The submenu item appears on the display. Press the [Setup] button to close the menu. Press the [Return] button to return to the previous menu. 1. Input/Output Assign 2. Speaker Setup 3. Audio Adjust 4. Source Setup 5. Listening Mode Preset 6. Miscellaneous 7. Hardware Setup 8. Remote Controller Setup 9. Lock Setup Menu Onscreen Setup Menus Display

If you connect your TV to the HDMI output, set the “Monitor Out” setting so that the onscreen setup menus are displayed and composite video, S-Video, and component video sources are upconverted and output. If you connect your TV to the COMPONENT VIDEO MONITOR OUT, set the “Monitor Out” setting so that the onscreen setup menus are displayed and composite video and S-Video sources are upconverted and output. You can specify the output resolution for the HDMI outputs and COMPONENT VIDEO MONITOR OUT and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported by your TV. Monitor Out Setup 1 Press the [Receiver] button, fol- lowed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. 2 Use the Up and Down [q]/[w] but- tons to select “1. Input/Output Assign”, and then press [Enter]. The “Input/Output Assign” menu appears. 3 Use the Up and Down [q]/[w] but- tons to select “1. Monitor Out”, and then press [Enter]. The “Monitor Out” menu appears. 1. Input/Output Assign 1. Monitor Out 2. HDMI Input 3. Component Video Input 4. Digital Audio Input 5. Analog Audio Input 6. Gamma Curve Monitor Out Resolution Brightness Contrast Hue Saturation HDMI Main Through 0 0 0 0 1–1. Monitor Out 4 Use the Up and Down [q]/[w] but- tons to select “Monitor Out”, and use the Left and Right [e]/[r] buttons to select: Analog: Select this if your TV is connected to the COMPONENT VIDEO MONITOR OUT, S MONITOR OUT, or V MONITOR OUT. HDMI Main: Select this if your TV is connected to the HDMI OUT MAIN. HDMI Sub: Select this if your TV is connected to the HDMI OUT SUB. Both: Select this if your TVs are con- nected to the HDMI OUT MAIN and HDMI OUT SUB. Video sig- nals are output from both HDMI outputs at the resolution supported by both TVs. Both (Main): Select this if your TVs are con- nected to the HDMI OUT MAIN and HDMI OUT SUB. Video sig- nals are output from both HDMI outputs but HDMI OUT MAIN will become a priority; depending on the resolution, video signals may not be output from HDMI OUT SUB. Both (Sub): Select this if your TVs are con- nected to the HDMI OUT MAIN and HDMI OUT SUB. Video sig- nals are output from both HDMI outputs but HDMI OUT SUB will become a priority; depending on the resolution, video signals may not be output from HDMI OUT MAIN. Notes: • If not connected to the same output you have selected in the“Monitor Out” setting, the “Monitor Out” setting will be automatically switched to “Analog”. • When you select other than “Analog”, the onscreen setup menus are output by only the HDMI outputs. If you’re not using the HDMI output and select settings by mistake and the menus disappear, press the [Monitor Out] button to select “Analog”. • For Deep Color output, if the “Monitor Out” setting is set to “Both (Main)” or “Both (Sub)”, the number of bit may be limited due to the capability of your TV connected to a priority output.

Notes: • See page 29 for charts showing how the “Monitor Out” and “Resolution” settings affect the video signal flow through the AV receiver. • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. 5 Use the Up and Down [q]/[w] but- tons to select “Resolution”, and use the Left and Right [e]/[r] buttons to select: Through: Select this to pass video through the AV receiver at the same resolution and with no conversion. Auto : Select this to have the AV receiver automatically convert video at reso- lutions not supported by your TV. 480p (480p/576p): Select this for 480p or 576p output and video conversion as necessary. 720p: Select this for 720p output and video conversion as necessary. 1080i: Select this for 1080i output and video conversion as necessary. 1080p : Select this for 1080p output and video conversion as necessary. 1080p/24 : Select this for 1080p output at 24 frames per second and video con- version as necessary. Source: Output will be according to the res- olution level which was set in the “Picture Adjust” setting (see page 111). Tips: • The “Resolution” setting can also be set using the [Video] button on the remote controller. • The “Resolution” setting is set respectively of main, sub, and analog. Notes: • Settings marked with an asterisk ( ) are not available when the “Monitor Out” setting is set to “Analog”. • If the “Monitor Out” setting is set to “Both”, this setting is fixed at “Auto”. • Depending on the incoming video signal, video playback may not be smooth or the vertical resolution may be lowered. In this case select other than “1080p/24”. * * * * 6 Press the [Setup] button. The setup menu closes.

HDMI Input Setup If you connect a video component to HDMI IN, you must assign that input to an input selector. For example, if you connect your DVD/BD player to HDMI IN 1, you must assign HDMI IN 1 to the DVD/BD input selector. If you’ve connected your TV to the AV receiver with an HDMI cable, you can set the AV receiver so that composite video, S-Video, and component video sources are upconverted* and output by the HDMI output. You can set this for each input selector by selecting the “- - - - -” option. Notes: • For composite video, S-Video, and component video upconversion for the HDMI output, the “Monitor Out” setting must be set to other than “Analog” (see page 49), and the “HDMI Input” setting must be set to “- - - - -”. See page 29 for more information on video signal flow and upconversion. • If no video component is connected to HDMI output (even if the HDMI input is assigned), the AV receiver selects the video source based on the setting of Component Video Input. • When an HDMI IN is assigned to an input selector, the AV receiver will select audio from HDMI IN as a pri- ority. See “Digital Audio Input Setup” on page 53. • The Tuner input selector cannot be assigned and is fixed at the “- - - - -” option. • If you connect an input component (such as UP-A1 Dock that seated iPod) to the UNIVERSAL PORT jack, you cannot assign any input to Port selector. • Do not assign the component connected with the HDMI input to the TV/Tape selector when you set “TV Control” setting to “On” (see page 120). Otherwise, appropriate CEC (Consumer Electronics Control) operation is not guaranteed. • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. Video Input Setup 1 Press the [Receiver] button fol- lowed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. 2 Use the Up and Down [q]/[w] but- tons to select “1. Input/Output Assign”, and then press [Enter]. The “Input/Output Assign” menu appears. 3 Use the Up and Down [q]/[w] but- tons to select “2. HDMI Input”, and then press [Enter]. The “HDMI Input” menu appears. IN OUT Composite video, S-Video, component video Composite video, S-Video, component video HDMI HDMI 1. Input/Output Assign 1. Monitor Out 2. HDMI Input 3. Component Video Input 4. Digital Audio Input 5. Analog Audio Input 6. Gamma Curve 1–2. HDMI Input DVD/BD VCR/DVR CBL/SAT GAME AUX 1 HDMI1 HDMI2 HDMI3 HDMI4 FRONT 4 Use the Up and Down [q]/[w] but- tons to select an input selector, and use the Left and Right [e]/ [r] buttons to select: HDMI1, HDMI2, HDMI3, HDMI4, HDMI5, HDMI6, HDMI7 (DTR-80.1): Select the HDMI IN to which the video component has been connected. - - - - -: Output composite video, S-Video, and component video sources from the HDMI outputs. The video output sig- nal from the HDMI outputs is the one configured in “Com- ponent Video Input Setup” (see page 52). • Each HDMI IN cannot be assigned to more than one input selector. When HDMI IN have already been assigned, you must set first any unused input selectors to “- - - - -” or you will be unable to assign HDMI IN to input selector. • “AUX 1” is used only for digital input from the front panel terminals. 5 Press the [Setup] button. The setup menu closes.

Component Video Input Setup If you connect to a COMPONENT VIDEO IN or PC INPUT ANALOG RGB (DTR-80.1), you must assign it to an input selector. For example, if you connect your DVD/BD player to COMPONENT VIDEO IN 2, you should assign it to the DVD/BD input selector. If you’ve connected your TV to the AV receiver with a component video cable, you can set the AV receiver so that composite video and S-Video sources are upconverted* and output by the COMPONENT VIDEO MONITOR OUT*1. You can set this for each input selector by selecting the “- - - - -” option. *1 Only when “Monitor Out” setting is set to “Analog”. Notes: • For composite video and S-Video upconversion for the COMPONENT VIDEO MONITOR OUT, the “Monitor Out” setting must be set to “Analog” (see page 49), and the “Component Video Input” setting must be set to “- - - - -”. See page 29 for more information on video signal flow and upconversion. • If not connected to the same output you have selected in the “Monitor Out” setting, the “Monitor Out” setting will be automatically switched to “Analog” (see page 49). • If you connect an input component (such as UP-A1 Dock that seated iPod) to the UNIVERSAL PORT jack, you cannot assign any input to Port selector. • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. ■About PC Input (DTR-80.1) Signals from PC INPUT ANALOG RGB are output from the HDMI output without the resolution conversion. Supported Resolution: • VGA (640 480) 60/72/75/85 Hz • SVGA (800 600) 56/60/72/75/85 Hz • XGA (1024 768) 60/70/75/85 Hz • SXGA (1280 1024) 60/75 Hz Note: The picture adjust setting is effective for only 60 Hz. 1 Press the [Receiver] button fol- lowed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. 2 Use the Up and Down [q]/[w] but- tons to select “1. Input/Output Assign”, and then press [Enter]. The “Input/Output Assign” menu appears. 3 Use the Up and Down [q]/[w] but- tons to select “3. Component Video Input”, and then press [Enter]. The “Component Video Input” menu appears. IN OUT Composite video, S-Video Composite video, S-Video Component video Component video 1. Input/Output Assign 1. Monitor Out 2. HDMI Input 3. Component Video Input 4. Digital Audio Input 5. Analog Audio Input 6. Gamma Curve 1–3. Component Video Input IN1 - - - - - IN2 IN3 - - - - - DVD/BD VCR/DVR CBL/SAT GAME AUX 1 4 Use the Up and Down [q]/[w] but- tons to select an input selector, and then use the Left and Right [e]/[r] buttons to select: IN1: Select if the video component is connected to COMPO- NENT VIDEO IN 1. IN2: Select if the video component is connected to COMPO- NENT VIDEO IN 2. IN3: Select if the video component is connected to COMPO- NENT VIDEO IN 3. PC IN: (DTR-80.1) Select if the per- sonal computer is connected to PC INPUT ANALOG RGB. - - - - -: Select if you are using the HDMI outputs, rather than the COMPONENT VIDEO OUT, for the output from composite video, S-Video, and component video sources. 5 Press the [Setup] button. The setup menu closes. × × × ×

If you connect a component to a digital input jack, you must assign that jack to an input selector. For example, if you connect your CD player to the OPTICAL IN1 jack, you should assign that jack to the CD input selector. By default, the COAXIAL IN1 jack is assigned to the DVD/ BD input selector, although this can be changed. Here are the default assignments. Notes: • Available sampling rate for PCM signals from a digital input (optical and coaxial) is 32/44.1/48/88.2/ 96 kHz/16, 20, 24 bit. • If you connect an input component (such as UP-A1 Dock that seated iPod) to the UNIVERSAL PORT jack, you cannot assign any input to Port selector. • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. Digital Audio Input Setup Input selector Default assignment (DTR-70.1) (DTR-80.1) DVD/BD COAX1 COAX1 VCR/DVR COAX2 COAX2 CBL/SAT COAX3 COAX3 Game OPT1 OPT1 AUX 1 FRONT (Fixed) FRONT (Fixed) AUX 2 - - - - - - - - - - TV/Tape - - - - - OPT2 Tuner - - - - - (Fixed) - - - - - (Fixed) CD OPT2 OPT3 Phono - - - - - - - - - - Port - - - - - - - - - - 1 Press the [Receiver] button fol- lowed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. 2 Use the Up and Down [q]/[w] but- tons to select “1. Input/Output Assign”, and then press [Enter]. The “Input/Output Assign” menu appears. 3 Use the Up and Down [q]/[w] but- tons to select “4. Digital Audio Input”, and then press [Enter]. The “Digital Audio Input” menu appears. 1. Input/Output Assign 1. Monitor Out 2. HDMI Input 3. Component Video Input 4. Digital Audio Input 5. Analog Audio Input 6. Gamma Curve 1–4. Digital Audio Input DVD/BD VCR/DVR CBL/SAT GAME AUX 1 COAX1 COAX2 COAX3 OPT1 FRONT 4 Use the Up and Down [q]/[w] but- tons to select an input selector, and use the Left and Right [e]/ [r] buttons to select “COAX1”, “COAX2”, “COAX3”, “OPT1”, “OPT2”, “OPT3” (DTR-80.1), or “- - - - - (analog)”. • When an HDMI IN is assigned to an input selector in “HDMI Input Setup” on page 51, the AV receiver will select audio from HDMI IN as a priority. • Press the [Enter] button when you do not use the signal of audio from the HDMI IN. The “ ” mark is dis- played like “COAX1 ”. • “AUX 1” is used only for digital input from the front panel terminals. Examples: If you connect your DVD player to the OPTICAL IN 1 jack, set “DVD/BD” to “OPT1”. If you want to listen to audio from the component connected to the OPTICAL IN 2 jack when the VCR/DVR input selector is selected, set “VCR/DVR” to “OPT2”. If you want to listen to audio from the component connected to the COAXIAL IN 1 jack when the CBL/ SAT input selector is selected, set “CBL/SAT” to “COAX1”. For input selectors that you don’t want to assign a digital input jack, set to “- - - - - (analog)”. 5 Press the [Setup] button. The setup menu closes. * *

If you connect a component to the AV receiver’s analog multichannel input, you must assign that input to an input selector. For example, if you connect your DVD/ BD player to the MULTI CH input, you must assign it to the DVD/BD input selector. Notes: • To listen to the component connected to the multichannel input, press the [Audio] button and select the “Audio selector” (see page 125). • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms. To use bi-amping, bridging or passive subwoofer, you must change the “Speakers Type(Front)” setting. For hookup information, see pages 21 to 23. Notes: • When bridging is used, the AV receiver is able to drive up to 7.2 speakers in the main room. • When bi-amping is used, the AV receiver is able to drive up to 7.2 speakers in the main room. • Before you change these settings, turn down the volume. Analog Audio Input Setup 1 Press the [Receiver] button, fol- lowed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. 2 Use the Up and Down [q]/[w] but- tons to select “1. Input/Output Assign”, and then press [Enter]. The “Input/Output Assign” menu appears. 3 Use the Up and Down [q]/[w] but- tons to select “5. Analog Audio Input”, and then press [Enter]. The “Analog Audio Input” menu appears. 4 Use the Left and Right [e]/[r] buttons to select an input selec- tor. You can assign the multichannel input to the following input selectors: “DVD/BD”, “VCR/DVR”, “CBL/ SAT”, “Game”, “AUX1”, “AUX2”, “TV/Tape”, “CD”, or “Phono”. If you don’t want to assign the multichannel input, set to “- - - - -”. 1. Input/Output Assign 1. Monitor Out 2. HDMI Input 3. Component Video Input 4. Digital Audio Input 5. Analog Audio Input 6. Gamma Curve Multich Subwoofer Input Sensitivity - - - - - 0dB 1–5. Analog Audio Input 5 Press the [Setup] button. The setup menu closes. Speaker Settings 1 Press the [Receiver] button, fol- lowed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. If you change these settings, you must run Audyssey MultEQ® XT Room Correction and Speaker Setup again (see page 58).

Powered Zone 2/3/4 See “Setting the Powered Zone 2/3/4” on page 141. Note: This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. 2 Use the Up and Down [q]/[w] but- tons to select “2. Speaker Setup”, and then press [Enter]. The “Speaker Setup” menu appears. 3 Use the Up and Down [q]/[w] but- tons to select “1. Speaker Set- tings”, and then press [Enter]. The “Speaker Settings” menu appears. 4 Use the Up and Down [q]/[w] but- tons to select “Speaker Imped- ance”, and then use the Left and Right [e]/[r] buttons to select: 4ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6. 6ohms: Select if the impedances of all speakers are between 6 and 16 ohms. Note: When bridging is used, “Speaker Impedance” setting is fixed at “8ohms”. 5 Use the Up and Down [q]/[w] but- tons to select “Speakers Type(Front)”, and then use the Left and Right [e]/[r] buttons to select: Normal: Select this if you’ve con- nected your front speakers normally. Bi-Amp: Select this if you’ve con- nected your front speakers for bi-amped operation. BTL: Select this if you’ve con- nected your front speakers for bridged operation. The BTL indicator will appear on the display. 2. Speaker Setup 1. Speaker Settings 2. Speaker Configuration 3. Speaker Distance 4. Level Calibration 5. Equalizer Settings 6. THX Audio Setup 2–1. Speaker Settings Speaker Impedance Speakers Type(Front) Passive Subwoofer Powered Zone2 Powered Zone3 Powered Zone4 6ohms Normal Not Use Not Act Not Act Not Act Note: Surround back speakers and Powered Zone 3/4 cannot be used if you select “Bi-Amp” or “BTL”. 6 Use the Up and Down [q]/[w] but- tons to select “Passive Sub- woofer”, and then use the Left and Right [e]/[r] buttons to select: Use: Select this if you’ve con- nected passive subwoofers. Not Use: Select this if you’ve con- nected no passive subwoof- ers. Note: Powered Zone 2/4 cannot be used if “Passive Subwoofer” is set to “Use”. 7 Press the [Setup] button. The setup menu closes.

For the onscreen setup menus to display properly, you must specify the TV system used in your area. Note: This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. For FM/AM tuning to work properly, you must specify the FM/AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. TV Format Setup (Australian models) 1 Press the [Receiver] button fol- lowed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. 2 Use the Up and Down [q]/[w] but- tons to select “6. Miscella- neous”, and then press [Enter]. The “Miscellaneous” menu appears. 3 Use the Up and Down [q]/[w] but- tons to select “2. OSD Setup”, and then press [Enter]. The “OSD Setup” menu appears. 4 Use the Up and Down [q]/[w] but- tons to select “TV Format”, and then use the Left and Right [e]/[r] buttons to select: Auto: Select this to automatically detect the TV system from the video input signals. NTSC: Select if the TV system in your area is NTSC. PAL: Select if the TV system in your area is PAL. 1. Volume Setup 2. OSD Setup 3. 12V Trigger A Setup 4. 12V Trigger B Setup 5. 12V Trigger C Setup 6. Miscellaneous 6–2. OSD Setup Immediate Display Display Position TV Format Language On Bottom Auto English 5 When you’ve finished, press the [Setup] button. The setup menu closes. FM/AM Frequency Step Setup 1 Press the [Receiver] button, fol- lowed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. 2 Use the Up and Down [q]/[w] but- tons to select “7. Hardware Setup”, and then press [Enter]. The “Hardware Setup” menu appears. 7. Hardware Setup 1. Remote ID 2. Multi Zone 3. Tuner 4. HDMI 5. Network 6. Firmware Update

Note: This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. If you connect an u-capable Onkyo MiniDisc recorder, CD recorder, or RI Dock to the TV/TAPE IN/ OUT jacks, or connect an RI Dock to the GAME IN or VCR/DVR IN jacks, for u to work properly, you must change this setting. This setting can only be changed on the AV receiver. Notes: • DOCK can be selected for the TV/Tape or Game or VCR/DVR input selector, but not at the same time. • Enter the appropriate remote control code before using the AV receiver’s remote controller for the first time (see page 150). 3 Use the Up and Down [q]/[w] but- tons to select “3. Tuner”, and then press [Enter]. The “Tuner” menu appears. (North American models) (Australian models) 4 Use the Left and Right [e]/[r] buttons to select: (North American models) 200kHz/10kHz: Select if 200 kHz/10 kHz steps are used in your area. 50kHz/9kHz: Select if 50 kHz/9 kHz steps are used in your area. (Australian models) 10kHz: Select if 10 kHz steps are used in your area. 9kHz: Select if 9 kHz steps are used in your area. 5 Press the [Setup] button. The setup menu closes. Changing the Input Display 7–3. Tuner FM/AM Frequency Step SAT Radio Mode 200kHz/10kHz None AM Frequency Step 9kHz 7–3. Tuner 1 Press the [TV/Tape], [Game] or [VCR/DVR] input selector button so that “TV/TAPE”, “GAME” or “VCR/DVR” appears on the dis- play. 2 Press and hold down the [TV/ Tape], [Game] or [VCR/DVR] input selector button (about 3 seconds) to change the setting. Repeat this step to select MD, CDR, or DOCK. For the TV/Tape input selector, the setting changes in this order: For the Game input selector, the setting changes in this order: GAME ↔ DOCK For the VCR/DVR input selector, the setting changes in this order: VCR/DVR ↔ DOCK VCR/DVR TV/ Tape Game or or or or (3 seconds) TV/TAPE → MD → CDR DOCK → →

With the supplied calibrated microphone, Audyssey MultEQ XT automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position. Audyssey MultEQ XT then removes the distortion caused by room acoustics by capturing room acoustical problems over the listening area in both the frequency and time domain. The result is clear, well-balanced sound for everyone. Enabling Audyssey MultEQ XT allows you to also use Audyssey Dynamic EQ™, which maintains the proper octave-to-octave balance at any volume level (see page 108). Before using this function, connect and position all of your speakers. If Audyssey Dynamic EQ is set to “On”, Audyssey Dynamic Volume™ becomes available. Measurement Positions To create a listening environment in your home theater that all listeners will enjoy, Audyssey MultEQ XT takes measurements at up to eight positions within the listening area. ■First measurement point Also referred to as the Main Listening Position this refers to the most central position where one would normally sit within the listening environment. MultEQ XT uses the measurements from this posi- tion to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer. ■Second−eighth measurement positions These are the other listening positions (i.e., the places where the other listeners will sit). You can measure up to eight positions. The following examples show some typical home theater seating arrangements. Choose the one that best matches yours, and position the microphone accordingly when prompted. Audyssey MultEQ® XT Room Correction and Speaker Setup About Audyssey Dynamic EQ Audyssey Dynamic EQ solves the problem of deterio- rating sound quality as volume is decreased by taking into account human perception and room acoustics. Dynamic EQ selects the correct frequency response and surround levels moment-by-moment at any user- selected volume setting. The result is bass response, tonal balance, and surround impression that remain constant despite changes in volume. Dynamic EQ combines information from incoming source levels with actual output sound levels in the room, a prereq- uisite for delivering a loudness correction solution. Audyssey Dynamic EQ works in tandem with Audyssey MultEQ XT to provide well-balanced sound for every listener at any volume level. About Audyssey Dynamic Volume Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the pre- ferred volume setting by the user and then monitors how the volume of program material is being per- ceived by listeners in real time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary rapid or gradual adjust- ments to maintain the desired playback volume level while optimizing the dynamic range. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal bal- ance, surround impression, and dialog clarity remain the same whether watching movies, flipping between television channels, or changing from stereo to sur- round sound content. – TV TV TV TV TV TV TV TV TV : listening area : listening position

Using Audyssey MultEQ® XT Enter qwer On/Standby Speaker setup microphone Notes: • If any of your speakers is 4 ohms, change “Speaker Impedance” setting before running Audyssey MultEQ XT Room Correction and Speaker Setup (see page 54). • If the AV receiver is muted, it will be unmuted automatically when Audyssey MultEQ XT Room Correction and Speaker Setup starts. • Room correction and speaker setup cannot be performed while a pair of headphones is connected. • It takes about 30 minutes to complete the room correction and speaker setup for eight positions. Total measurement time varies depending on the number of speakers. • Do not disconnect the speaker setup microphone during the room correction and speaker setup, unless you want to cancel the setup. • Do not connect or disconnect any speakers during the room correction and speaker setup. 1 Turn on the AV receiver and the connected TV. On the TV, select the input to which the AV receiver is connected. 2 Set the speaker setup micro- phone at the Main Listening Posi- tion a (page 58), and connect it to the Setup Mic jack. The speaker setting menu appears. If you change these settings, refer to step 5 on “Speaker Settings” (page 54) or step 4 on “Setting the Powered Zone 2/3/4” (page 141). 3 When you’ve finished, press the [Enter] button. Notes: • Before starting Audyssey MultEQ XT Room Correction and Speaker Setup, arrange the room and connect the speakers as you would for enjoying movies. Changes to the room after auto setup requires you run the auto setup again, as room EQ characteristics may have changed. • When starting the room correction and speaker setup, do not stand between the speakers and microphone, and avoid obstacles blocking the path between speakers and microphone. This will produce inaccurate results. • Position the microphone at ear height of a seated listener with the microphone tip pointed directly at the ceiling using a tripod. Do not hold the microphone in your hand during measurements as this will produce inacurate results. MultEQ XT: Auto Setup Speakers Type(Front) Passive Subwoofer Powered Zone2 Powered Zone3 Powered Zone4 Normal Not Use Not Act Not Act Not Act MultEQ XT: Auto Setup Please place setup microphone at center of listening area at ear height. Next

• Make the room as quiet as possible. Background noise can disrupt the room measurements. Close windows, silence cell phones, televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices. • Cell phones should be turned off or placed away from all audio electronics during the measurement process as Radio Frequency Interference (RFI) may cause measurement disruptions (even if the cell phone is not in use). 4 Press [Enter]. The room correction and speaker setup starts. Test tones are played through each speaker as Audyssey MultEQ® XT Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. 5 The following screen appears. Place the setup microphone at the next position (page 58), and then press [Enter]. Audyssey MultEQ XT performs more measurements. This takes a few minutes. MultEQ XT: Auto Setup Do not unplug setup microphone. Please keep quiet. Now measuring. . . MultEQ XT: Auto Setup Next Please place setup microphone at 2nd position at ear height. MultEQ XT: Auto Setup Do not unplug setup microphone. Please keep quiet. Now measuring. . . 6 When prompted, place the setup microphone at the next position, and repeat step 5. 7 After the 3rd to the 8th measure- ment, the following screen appears. Use the Up and Down [q]/[w] but- tons to select an option, and then press [Enter]. Next: Select “Next” to begin measuring the next measurement position. After the 8th measurement has been taken, the procedure automatically proceeds to step 8. Finish(Calculate): Select this if you don’t want to measure any more listening posi- tions and are ready to calculate the results, then go to step 8. 8 When the measurements are complete, the following screen appears. MultEQ XT: Auto Setup Next Finish(Calculate) Please select [Next], when measuring next position, and select [Finish], when ending. MultEQ XT: Auto Setup Calculating...

Notes: • When the room correction and speaker setup is complete, the “Equalizer Settings” (page 104) will be set to “Audyssey” and “Dynamic EQ” (page 108) will be set to “On”. • You can cancel the Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone. Error Messages While the room correction and speaker setup is in progress, one of the following error messages may appear: ❏Ambient noise is too high. This message appears if the background noise is too loud and the measurements cannot be performed properly. Remove the source of the noise and try again. Retry: Return to the measured point immediately before and start set up again. Cancel: Cancel the room correction and speaker setup. ❏Speaker Detect Error This message appears if a speaker is not detected. “Yes” means that a speaker was detected. “No” means that no speaker was detected. Tip: See “Speaker Configuration” (page 18) for appropriate settings. The front speaker has not been detected. 9 When the calculations are com- plete, the following screen appears. Use the Up and Down [q]/[w] but- tons to select an option, and then press [Enter]. The options are: Save: Save the calculated settings and exit the room correction and speaker setup. Cancel: Cancel the room correction and speaker setup. Note: You can view the calculated settings for the speaker configuration, speaker dis- tances, and speaker levels by using the Left and Right [e]/[r] buttons. 10 If you selected “Save”, the results are saved, and the following screen appears. 11 Disconnect the speaker setup microphone. Subwoofer No Front Full Band Center 40Hz Surround 120Hz Front Wide Full Band Front High Full Band Surr Back 150Hz Surr Back Ch 2ch -- Review SP Configuration -- MultEQ XT: Auto Setup Save Cancel MultEQ XT: Auto Setup Saving... MultEQ XT: Auto Setup Please, unplug setup microphone. MultEQ XT: Auto Setup Retry Cancel Ambient noise is too high. FL : No SL : --- FWL : --- FHL : --- SBL : --- C : --- FR : --- SR : --- FWR : --- FHR : --- SBR : --- SW1 : --- SW2 : --- MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error

One of the front speakers has not been detected. One of the front wide speakers has not been detected. One of the front high speakers has not been detected. One of the surround speakers has not been detected. The surround back speakers have been detected but the surround speakers haven’t. The front high speakers have been detected but the surround speakers haven’t. The front wide speakers have been detected but the surround speakers haven’t. The right surround back speaker has been detected but the left surround back speaker hasn’t. The left surround back speaker has been detected but the surround speaker hasn’t. Subwoofer 2 has been detected but Subwoofer 1 has not. MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error FL : Yes SL : --- FWL : Yes FHL : Yes SBL : --- C : Yes FR : No SR : --- FWR : Yes FHR : Yes SBR : --- SW1 : --- SW2 : --- FL : Yes SL : --- FWL : Yes FHL : Yes SBL : --- C : Yes FR : --- SR : --- FWR : No FHR : Yes SBR : --- SW1 : --- SW2 : --- MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error FL : Yes SL : --- FWL : Yes FHL : Yes SBL : --- C : Yes FR : --- SR : --- FWR : --- FHR : No SBR : --- SW1 : --- SW2 : --- MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error FL : Yes SL : No FWL : Yes FHL : Yes SBL : Yes C : Yes FR : Yes SR : Yes FWR : Yes FHR : Yes SBR : Yes SW1 : --- SW2 : --- MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error FL : Yes SL : --- FWL : No FHL : No SBL : --- C : Yes FR : Yes SR : No FWR : No FHR : No SBR : Yes SW1 : --- SW2 : --- MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error FL : Yes SL : --- FWL : No FHL : Yes SBL : --- C : Yes FR : Yes SR : No FWR : No FHR : Yes SBR : --- SW1 : --- SW2 : --- MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error FL : Yes SL : --- FWL : Yes FHL : No SBL : --- C : Yes FR : Yes SR : No FWR : Yes FHR : No SBR : --- SW1 : --- SW2 : --- FL : Yes SL : --- FWL : Yes FHL : Yes SBL : No C : Yes FR : Yes SR : Yes FWR : Yes FHR : Yes SBR : Yes SW1 : --- SW2 : --- MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error FL : Yes SL : --- FWL : No FHL : No SBL : Yes C : Yes FR : Yes SR : No FWR : No FHR : No SBR : No SW1 : --- SW2 : --- MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error FL : Yes SL : Yes FWL : Yes FHL : Yes SBL : Yes C : Yes FR : Yes SR : Yes FWR : Yes FHR : Yes SBR : Yes SW1 : No SW2 : Yes MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error

The speaker type detected does not match what was expected. The speaker may be incorrect type or bro- ken. Please check that it is the correct speaker type. ❏Speaker Matching Error! The number of speakers detected on the second mea- surement and later was different to the number detected on the first measurement. Make sure speakers that could not be detected are connected properly. Retry: Return to step 2 and try again. Cancel: Cancel the room correction and speaker setup. ❏Writing Error! This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, the AV receiver is probably malfunctioning. Contact the dealer from whom you purchased this unit. Retry: Return to step 2 and try again. Cancel: Cancel the room correction and speaker setup. Changing the Speaker Settings Manually If you wish to make changes to the settings found during the room correction and speaker setup, follow the directions on pages 102 to 105. Notes: • Please note that THX recommends any THX main speakers be set to “80Hz(THX)”. If you set up your speakers using Audyssey MultEQ XT Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to 80 Hz (THX) crossover (see page 102). • Sometimes due to the electrical complexities of subwoofers and the interaction with the room, THX recommends setting the level and the distance of the subwoofer manually. • Sometimes due to interaction with the room, you may notice irregular results when setting the level and/or distance of the main speakers. If this happens, THX recommends setting them manually. Using Powered Subwoofers If you’re using powered subwoofers that output very low-frequency sound at a low volume level, it may not be detected by Audyssey MultEQ® XT Room Correction and Speaker Setup. If the “Subwoofer” appears on the “Review SP Configuration” screen as “No”, increase the subwoofer’s volume to the half-way point, set it to its highest crossover frequency, and then try running Audyssey MultEQ XT Room Correction and Speaker Setup again. Note that if the volume is set too high and the sound distorts, detection issues may occur, so use an appropriate volume level. If the subwoofer has a low- pass filter switch, set it to Off or Direct. Refer to your subwoofer’s instruction manual for details. FL : Error SL : Yes FWL : --- FHL : --- SBL : Yes C : Yes FR : Yes SR : Yes FWR : --- FHR : --- SBR : Yes SW1 : Yes SW2 : Yes MultEQ XT: Auto Setup Retry Cancel Speaker Detect Error MultEQ XT: Auto Setup Retry Cancel Speaker Matching Error! MultEQ XT: Auto Setup Retry Cancel Writing Error!

Selecting the Input Source 1 Use the AV receiver’s input selector buttons to select the input source. To select the input source with the remote controller, press the [Receiver] button, and then press the Input Selector buttons. 2 Start playback on the source component. When you select DVD or another video component, on your TV, you’ll need to select the video input that’s connected to the AV receiver’s HDMI outputs, COMPONENT VIDEO MONITOR OUT or MONITOR OUT. On some DVD players, you may need to turn on the digital audio output. 3 To adjust the volume, use the Master Volume control, or the remote controller’s VOL [q]/[w] button. The volume can be set to –Q dB, –81.5 dB through +18.0 dB (relative dis- play). The AV receiver is designed for home theater enjoyment. It has a wide volume range, allowing precise adjustment. The volume level can also be displayed as an absolute value. See “Volume Setup” on page 116. 4 Select a listening mode and enjoy! See “Using the Listening Modes” on page 88. Master Volume VOL q/w Input Selector Receiver Input selector buttons Remote controller AV receiver or or AV receiver Remote controller

except when the Direct or THX listening mode is selected. ■Bass You can boost or cut low-frequency sounds output by the front speakers from –10 dB to +10 dB in 2 dB steps. ■Treble You can boost or cut high-frequency sounds output by the front speakers from –10 dB to +10 dB in 2 dB steps. Notes: • This setting is not available when the multichannel Analog input is selected. • To bypass the bass and treble tone circuits, select the Direct or THX listening mode. You can display various information about the current input source as follows. Note: This procedure can also be performed on the AV receiver by using its [Display] button. The following information can typically be displayed for input sources. * If the input signal is analog, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format and the number of channels is displayed. For some digital input sig- nals, including multichannel PCM, the signal format, number of channels, and sampling frequency is displayed. Information is displayed for about three seconds, then the previ- ously displayed information reappears. Adjusting the Bass & Treble 1 AV receiver Press the [Tone] button repeat- edly to select either “Bass” or “Treble” for each speaker or sub- woofer. 2 AV receiver Use the Down and Up [–]/[+] but- tons to adjust. Tip: This procedure can also be performed on the remote controller by using [Audio] button (see page 123). Tone, –, + Dimmer Display Display Dimmer Muting Sleep SP Layout Press [Receiver] first. Displaying Source Information Remote controller Press the [Receiver] button, and then press the [Display] button repeatedly to cycle through the available information. Sampling frequency Input source Signal format* Listening mode Input Signal Resolution Output Resolution

You can temporarily mute the output of the AV receiver. Tip: You can specify how much the output is muted with the “Muting Level” setting (page 116). With the sleep timer, you can set the AV receiver to turn off automatically after a specified period. If you need to cancel the sleep timer, press the [Sleep] button repeatedly until the SLEEP indicator disappears. To check the time remaining until the AV receiver sleeps, press the [Sleep] button. Note that if you press the [Sleep] button while the sleep time is being displayed, you’ll shorten the sleep time by 10 minutes. Front High or Front Wide Speakers • When the Powered Zone 2 is being used (page 141), this setting cannot be selected. • When the listening mode that doesn’t support Front High or Front Wide speakers is used, the setting can- not be selected. • If you use surround back speakers, the speaker selec- tion will be based on the combination of surround back and front high speakers, or surround back and front wide speakers. You can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver’s Phones jack for private listening, as shown. Notes: • Always turn down the volume before connecting your headphones. • While the headphones plug is inserted in the Phones jack, the Headphone indicator, speaker/channel indi- cator FL and FR light up. (The Powered Zone 2/3/4 speakers are not turned off.) • When you connect a pair of headphones, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono or Direct. • The following listening modes can be used with head- phones (the listening modes available also depend on the currently selected input source): Stereo, Direct, and Mono. Setting the Display Brightness Remote controller Press the [Receiver] button, and then press the [Dimmer] button repeatedly to select: dim, dim- mer, or normal brightness. Alternatively, you can use the AV receiver’s [Dimmer] button (North American models). Muting the AV Receiver Remote controller Press the [Receiver] button, and then press the [Muting] button. The output is muted and the MUTING indicator flashes on the display, as shown. To unmute the AV receiver, press the [Muting] button again, or adjust the volume. The Mute function is cancelled when the AV receiver is set to Standby. Using the Sleep Timer Remote controller Press the [Receiver] button, and then press the [Sleep] button repeatedly to select the required sleep time. The sleep time can be set from 90 to 10 minutes in 10 minute steps. The SLEEP indicator appears on the display when the sleep timer has been set. The specified sleep time appears on the display for about five seconds, then the previous display reappears. Selecting Speaker Layout Remote controller Press the [Receiver] button, and then press the [SP Layout] but- ton repeatedly. Using Headphones

mode, you can sequentially operate Integra/Onkyo com- ponents with simple commands by simply pressing one button. These commands are user-specifiable (see page 159) and the default actions are described below. Press the Activities buttons to start the Easy macro com- mand. Once the AV receiver has entered the normal macro mode, all of the Activities buttons will automatically switch to the normal macro mode. In this case, pressing the [All Off] button will set only the AV receiver to Standby mode. *1. Depending on the start-up time of the DVD/BD player, the AV receiver may not activate this playback command. In this case, press the Play [1] button on the remote controller. *2. When [My Music] is selected, with the default settings, this will not be performed. *3. With some televisions, the power may not be turned off (or enter standby). Using Easy Macros 1 Press the [My Movie], [My TV], or [My Music] button. My Movie (default): 1. The TV connected to the AV receiver is turned on. 2. The Integra/Onkyo DVD player connected to the AV receiver is turned on. 3. The AV receiver is turned on. 4. The input selector of the AV receiver is set to “DVD/BD”. 5. The player starts playback. *1 My TV (default): 1. The TV connected to the AV receiver is turned on. 2. The cable set-top box connected to the AV receiver is turned on. 3. The AV receiver is turned on. 4. The input selector of the AV receiver is set to “CBL/SAT”. You can enjoy cable TV. Receiver Audio All Off, My Movie, My TV, My Music Activities buttons My Music (default): 1. The Integra/Onkyo CD player con- nected to the AV receiver is turned on. 2. The AV receiver is turned on. 3. The input selector of the AV receiver is set to “CD”. 4. The player starts playback. Note: Once you start the Easy macro com- mand, you cannot use other Activities buttons during the execution. If you want to operate other components half- way, press the [All Off] to stop and press desired Activities button. 2 Press the [All Off] button. 1. The connected component stops and turns off. 2. The AV receiver turns off. 3. The TV connected to the AV receiver turns off (Standby). *2*3

When you want to operate the component that is not assigned as the source component, you can assign it as the source component. For the default assignment, see page 160. Restoring Default (3 seconds) While holding down the Remote Mode button, press and hold down the [My Movie], [My TV], or [My Music] button (about 3 sec- onds). The Activities buttons that you pressed flashes twice, indicating that the setting has been established. Examples: When you press the [My Music] button and want to start the Onkyo Cassette recorder, while holding down [TV/ Tape] button, press and hold down the [My Music] button (about 3 seconds) flashes twice. Tip: This procedure can also be performed via onscreen menu (see page 159). 1 (3 seconds) While holding down the [Audio] button, press and hold down the [All Off] button until the [All Off] button lights up (about 3 sec- onds). 2 Release the [Audio] and [All Off] buttons and press the [All Off] button again. The [All Off] button flashes twice.

With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. Listening to the Radio Tuning into Radio Stations ■Auto Tuning Mode When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator appears on the display, as shown. ■Manual Tuning Mode This model changes FM/AM frequency in 200k/10k (or 50k/9k) Hz steps. In Manual Tuning mode, FM stations will be in mono. Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. ■Tuning into Stations by Frequency You can tune into AM and FM stations directly by enter- ing the appropriate frequency. Using the Tuner Use the [Tuner] input selector button to select either AM or FM. In this example, FM has been selected. Each time you press the [Tuner] button, the input source changes between AM and FM. (Actual display depends on country.) 1 Press the [Tuning Mode] button so that the AUTO indicator appears on the display. 2 Press the Tuning Up or Down [q]/ [w] buttons. Searching stops when a station is found. Tuning q/w Tuner Tuning Mode Band Frequency 1 Press the [Tuning Mode] button so that the AUTO indicator disap- pears from the display. 2 Press and hold the Tuning Up or Down [q]/[w] buttons. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. 1 Remote controller Press the [Tuner] button repeat- edly to select AM or FM, followed by the [D.TUN] button. (Actual display depends on country.) 2 Remote controller Within 8 seconds, use the num- ber buttons to enter the fre- quency of the radio station. For example, to tune to 87.5 (FM), press 8, 7, 5. TUNED FM STEREO AUTO

You can store a combination of up to 40 of your favorite AM/FM radio stations as presets. Note: You can name your radio presets for easy identification (see page 111). Its name is displayed instead of the band and frequency. Selecting Presets Deleting Presets Presetting AM/FM Stations 1 Tune into the AM/FM station that you want to store as a preset. 2 Press the [Memory] button. The preset number flashes. 3 While the preset number is flash- ing (about 8 seconds), use the Preset [e]/[r] buttons to select a preset from 1 through 40. 4 Press the [Memory] button again to store the station or channel. The station or channel is stored and the preset number stops flashing. Repeat this procedure for all of your favorite AM/FM radio stations. Preset e/r Memory Preset e/r AV receiver or Remote controller or To select a preset, use the Preset [e]/[r] buttons, or the remote controller’s CH [+/–] button. Remote controller You can also use the remote con- troller’s number buttons to select a preset directly. 1 Select the preset that you want to delete. See the previous section. 2 While holding down the [Mem- ory] button, press the [Tuning Mode] button. The preset is deleted and its number disappears from the display. Memory, Tuning Mode

To listen to Satellite Radio, you’ll need to connect a SIR- IUS Satellite Radio tuner (sold separately) to your Sir- ius-Ready receiver. SIRIUS Satellite Radio is available to residents of the US (except Alaska and Hawaii) and Canada. Satellite Radio delivers a variety of commercial-free music from categories ranging from Pop, Rock, Country, R&B, Dance, Jazz, Classical and many more plus cover- age of all the top professional and college sports includ- ing play by play games from select leagues and teams. Additional programming includes expert sports talk, uncensored entertainment, comedy, family program- ming, local traffic and weather and news from your most trusted sources. Once you’ve purchased a SIRIUS tuner you’ll need to activate it and subscribe to begin enjoying the service. Easy to follow installation and setup instructions are pro- vided with the SIRIUS tuner. There are a variety of pro- gramming packages available, including the option of adding “The Best of XM” programming to the SIRIUS service. The Best of XM service is not available to SIR- IUS Canada subscribers at this time. Please check with SIRIUS Canada for any updates using the numbers and web address below. Family friendly packages are also available to restrict channels featuring content that may be inappropriate for children. To subscribe to SIRIUS, U.S. and Canadian customers can call 1-888-539-SIRI (1-888-539-7474) or visit sir- ius.com (US) or siriuscanada.ca (Canada). Setting Up the SiriusConnect™ Home Tuner The optional SiriusConnect Home tuner kit includes everything for easy home installation, including the Sir- iusConnect receiver, indoor/outdoor antenna with 21- foot cable, 8-pin mini DIN connector cable, and an AC power adapter. See the SiriusConnect Home tuner’s instructions for more information. Use the 8-pin mini DIN connector cable to connect the SiriusConnect receiver to the SIRIUS jack on the rear of the AV receiver. To use the included antenna indoors, you must place it at a north-, west-, or east-facing window, depending on where you live. If this isn’t possible, you’ll need to install it outside, away from any overhead obstructions. Positioning the Antenna For a consistent satellite signal, the antenna must be positioned correctly. Use the following map to determine which area you are in and position the antenna accord- ingly. Area 1: Point the antenna toward the sky in the east, northeast, or southeast, either through a window or out- side. Area 2: Point the antenna toward the sky in the north or northeast, either through a window or outside. Area 3: Point the antenna toward the sky in the north or northwest, either through a window or outside. Area 4: Point the antenna toward the sky in the west, northwest, or southwest, either through a window or outside. Area 5: Put the antenna outside and point it straight up. The antenna cannot be used indoors. Listening to Satellite Radio (North American models) SIRIUS, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries. All rights reserved. Service not available in Alaska and Hawaii. SiriusConnect receiver 8-pin mini DIN connector cable AC power Indoor/outdoor antenna with 21-foot cable AV receiver SIRIUS jack 1 2 3 4 5 HORIZON SKY SOUTH WEST EAST NORTH

Setting the Satellite Radio Mode Before you can listen to SIRIUS Satellite Radio, you must set the “SAT Radio Mode” to “SIRIUS”. Note: This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. 1 Remote controller Press the [Receiver] button, fol- lowed by the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [q]/[w] but- tons to select “7. Hardware Setup”, and then press [Enter]. The “Hardware Setup” menu appears. Setup Receiver qwer Enter 7. Hardware Setup 1. Remote ID 2. Multi Zone 3. Tuner 4. HDMI 5. Network 6. Firmware Update 3 Use the Up and Down [q]/[w] but- tons to select “3. Tuner”, and then press [Enter]. The “Tuner” screen appears. 4 Use the Up and Down [q]/[w] but- tons to select “SAT Radio Mode”, and use the Left and Right [e]/ [r] buttons to select “SIRIUS”. Pressing the Left and Right [e]/[r] buttons cycles through the following options: None Q SIRIUS None: Select if you’re not using Satellite Radio. SIRIUS: Select to use SIRIUS Satel- lite Radio. 5 When you’ve finished, press the [Setup] button. The setup menu closes. 7–3. Tuner FM/AM Frequency Step SAT Radio Mode 200kHz/10kHz None

Selecting SIRIUS Satellite Radio Note: This procedure can also be performed on the AV receiver. Press the [Tuner] button repeatedly to select “SIRIUS”. Signing Up for SIRIUS Satellite Radio Before you can use SIRIUS Satellite Radio, you must first sign up for an account. You’ll need a major credit card and your SIRIUS Satellite Radio ID, which you can get from the AV receiver, as explained below, or from the SiriusConnect Home tuner package. Note: Your ID is also displayed on the Satellite Radio screen. See “Positioning the SiriusConnect Home Antenna” on page 80. Selecting SIRIUS Satellite Radio Channels There are three ways to select SIRIUS Satellite Radio channels: 1. Channel Search mode: select any channel. 2. Category Search mode: select channels by cate- gory. 3. Direct tuning: enter channel number. ■Channel Search Mode Remote controller Press the [Receiver] button, and then press the [Tuner] button repeatedly to select “SIRIUS”. If “CHECK SR TUNER” appears on the display, make sure the SiriusCon- nect receiver is connected properly. If “ANTENNA ERROR” appears, make sure the antenna is connected properly. 1 AV receiver Use the Tuning Up and Down [q]/ [w] buttons to select channel 0. Your SIRIUS Satellite Radio ID num- ber is displayed. Write it below. ID 2 To sign up, go to: http://activate.siriusradio.com or call: 1-888-539-SIRIUS (7474) Tuning q/w 1 Remote controller Press the [Tuner] button, and then press the [Enter] button repeatedly to select Channel Search mode. 2 Use the Up and Down [q]/[w] but- tons to select a channel. You can also use the Left and Right [e]/[r] buttons to select a category. Tuner Receiver qwer Enter Channel name Channel number

■Category Search Mode ■Direct Tuning You can select a SIRIUS Satellite Radio channel directly by entering its number. Notes: • If you select an unavailable channel, “INVALID CHANNEL” appears on the display. • If you select a channel that you are not subscribed to, “CALL SIRIUS” appears on the display. • Channels that are locked must be unlocked before you can listen to them. See “SIRIUS Parental Lock” on page 76 for more information. ■Selecting the Previous Channel 1 Remote controller Press the [Tuner] button, and then press the [Enter] button repeatedly to select Category Search mode. 2 Use the Left and Right [e]/[r] buttons to select a category, and use the Up and Down [q]/[w] but- tons to select a channel in that category. Return CH +/– Tuner qwer D.TUN Number buttons 1 Remote controller Press the [Tuner] button, fol- lowed by the [D.TUN] button. 2 Within 8 seconds, use the num- ber buttons to enter the channel number. For example, to select channel #20, press 0, 2, 0, or 2, 0. AV receiver or Remote controller To listen to the previously selected SIRIUS Satellite Radio channel, press the [Return] but- ton.

Selecting Channels on the AV Receiver Presetting SIRIUS Satellite Radio Channels You can store a combination of up to 40 of your favorite SIRIUS Satellite Radio channels and AM/FM radio sta- tions as presets. 1 AV receiver Press the [Tuner] button repeat- edly to select “SIRIUS”. 2 Press the [Tuning Mode] button repeatedly to select Channel Search mode or Category Search mode. 3 Press the [Enter] button repeat- edly to select a category. 4 Use the Tuning Up and Down [q]/ [w] buttons to select a channel. In Channel Search mode, you can select any channel. In Category Search mode, you can only select channels from the currently selected category. Tuning q/w Tuning Mode Return Tuner Enter 1 Tune into the SIRIUS channel that you want to store as a preset. 2 AV receiver Press the [Memory] button. The preset number flashes. 3 While the preset number is flash- ing (about 8 seconds), use the Preset [e]/[r] buttons to select a preset from 1 through 40. 4 Press the [Memory] button again to store the channel. The channel is stored and the preset number stops flashing. Repeat this procedure for all of your favorite SIRIUS Satellite Radio chan- nels. Memory Preset e/r Tuning Mode

■Selecting Presets ■Deleting Presets SIRIUS Parental Lock With SIRIUS Parental Lock, you can lock out channels that you do not want to receive and use a 4-digit PIN number to prevent others from unlocking them. AV receiver or Remote controller To select a preset, use the Preset [e]/[r] buttons, or the remote controller’s CH [+/–] button. You can also use the remote controller’s number buttons to select a preset directly. 1 Select the preset that you want to delete. See the previous section. 2 AV receiver While holding down the [Memory] button, press the [Tun- ing Mode] button. The preset is deleted and its number disappears from the display. 1 Remote controller Press the [Receiver] button, fol- lowed by the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [q]/[w] but- tons to select “7. Hardware Setup”, and then press [Enter]. The “Hardware Setup” menu appears. Setup Receiver qwer Enter 7. Hardware Setup 1. Remote ID 2. Multi Zone 3. Tuner 4. HDMI 5. Network 6. Firmware Update

3 Use the Up and Down [q]/[w] but- tons to select “3. Tuner”, and then press [Enter]. The “Tuner” screen appears. 4 Use the Up and Down [q]/[w] but- tons to select “SIRIUS Parental Lock”, and then press [Enter]. The “SIRIUS Parental Lock” screen appears. Note: If the “SAT Radio Mode” is set to “None” (see page 72), the “SIRIUS Parental Lock” item is not available. 7–3. Tuner FM/AM Frequency Step SAT Radio Mode Antenna Aiming SIRIUS Parental Lock 200kHz/10kHz SIRIUS SIRIUS Parental Lock Enter Code 0 1 2 3 4 5 6 7 8 9 5 Use the Left and Right [e]/[r] buttons to select a number on the screen, and then press [Enter]. Repeat this for each of the four digits in the PIN number. If you’re entering the PIN number for the very first time, the PIN is stored, and the following screen appears. If you’ve already set a PIN number, you must enter the correct PIN to get to this screen. If you enter the wrong PIN, the message “Wrong Code!” appears and you’ll have to enter the PIN again. Note: The “SIRIUS Parental Lock” cannot be set unless the AV receiver and the Siri- usConnect receiver are connected. 6 Use the Up and Down [q]/[w] but- tons to select “Parental Lock”, and then press [Enter]. The “Parental Lock” screen appears. 7 Use the Up and Down [q]/[w] but- tons to select a channel, and use the Left and Right [e]/[r] but- tons to select “Locked” or “Unlocked”. The number, name, and status of the currently selected channel is displayed. -> SIRIUS Parental Lock Edit Code Parental Lock

Notes: • While a channel is locked, it cannot be selected for listening. • To unlock a channel, you must enter the correct PIN number and change it to Unlocked in step 6. • This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. Changing the PIN Number 8 When you’ve finished, press [Enter] to save your changes, or press [Return] to return to the previous screen without saving. When [Enter] is pressed, the confirma- tion message “Locked” or “Unlocked” appears. 9 Press the [Setup] button. The setup menu closes. 1 Remote controller Press the [Receiver] button, fol- lowed by the [Setup] button. The main menu appears onscreen. Setup Receiver qwer Enter 2 Use the Up and Down [q]/[w] but- tons to select “7. Hardware Setup”, and then press [Enter]. The “Hardware Setup” menu appears. 3 Use the Up and Down [q]/[w] but- tons to select “3. Tuner”, and then press [Enter]. The “Tuner” screen appears. 4 Use the Up and Down [q]/[w] but- tons to select “SIRIUS Parental Lock”, and then press [Enter]. The “SIRIUS Parental Lock” screen appears. Note: If the “SAT Radio Mode” is set to “None” (see page 72), the “SIRIUS Parental Lock” item is not available. 7. Hardware Setup 1. Remote ID 2. Multi Zone 3. Tuner 4. HDMI 5. Network 6. Firmware Update 7–3. Tuner FM/AM Frequency Step SAT Radio Mode Antenna Aiming SIRIUS Parental Lock 200kHz/10kHz SIRIUS SIRIUS Parental Lock Enter Code 0 1 2 3 4 5 6 7 8 9

Displaying SIRIUS Satellite Radio Information The following information can be displayed: Note: If the category, artist/composer, or song title is not avail- able, “- - -” will be displayed instead. 5 Use the Left and Right [e]/[r] buttons to select a number on the screen, and then press [Enter]. Repeat this for each of the four digits in the PIN number. If you’re entering the PIN number for the very first time, the PIN is stored, and the following screen appears. If you’ve already set a PIN number, you must enter the correct PIN to get to this screen. If you enter the wrong PIN, the message “Wrong Code!” appears and you’ll have to enter the PIN again. Note: The “SIRIUS Parental Lock” cannot be set unless the AV receiver and the Siri- usConnect receiver are connected. 6 Use the Up and Down [q]/[w] but- tons to select “Edit Code”, and then press [Enter]. The “New Code” screen appears. 7 Use the Left and Right [e]/[r] buttons to select a number on the screen, and then press [Enter]. Repeat this for each of the four digits in the new PIN number. The “Confirm” screen appears. -> SIRIUS Parental Lock Edit Code Parental Lock SIRIUS Parental Lock New Code 0 1 2 3 4 5 6 7 8 9 SIRIUS Parental Lock Confirm 0 1 2 3 4 5 6 7 8 9 8 Confirm the new PIN number by entering it again. If you confirm the PIN number cor- rectly, the new PIN is saved and the message “Complete” appears. If you confirm the PIN number incor- rectly, “Wrong Code!” appears, and you’ll be returned to step 5 to try again. 9 Press the [Setup] button. The setup menu closes. Remote controller Press the [Display] button repeatedly to cycle through the available information. Display Channel name Category Artist/composer Song title Listening mode

Positioning the SiriusConnect Home Antenna You can check the strength of the SIRIUS Satellite Radio signal and adjust the position of the SiriusConnect Home antenna accordingly. Notes: • So long as the signal strength is good, you can enjoy SIRIUS Satellite Radio by using either satellite or ter- restrial reception. • Terrestrial signals are only available in certain areas. • The SIRIUS information on the Satellite Radio screen is only displayed when the “SAT Radio Mode” is set to “SIRIUS” (see page 72). 1 Remote controller Press the [Receiver] button, fol- lowed by the [Tuner] button, and [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [q]/[w] but- tons to select “7. Hardware Setup”, and then press [Enter]. The “Hardware Setup” menu appears. Note: If the “SAT Radio Mode” is set to “None” (see page 72), the “Antenna Aiming” item is not available. Setup Receiver qwer Enter Tuner 7. Hardware Setup 1. Remote ID 2. Multi Zone 3. Tuner 4. HDMI 5. Network 6. Firmware Update 3 Use the Up and Down [q]/[w] but- tons to select “3. Tuner”, and then press [Enter]. The “Tuner” screen appears. 4 Use the Up and Down [q]/[w] but- tons to select “Antenna Aiming”, and then press [Enter]. The Satellite Radio screen appears. The name of the currently selected input selector is displayed in a box. 5 Position the SiriusConnect Home antenna so that as many bars as possible (up to 3) appear on the SIRIUS Satellite signal strength meter. If you cannot receive a satellite signal, position the SiriusConnect Home antenna so that as many bars as possible (up to 3) appear on the SIRIUS Terres- trial signal strength meter. 7–3. Tuner FM/AM Frequency Step SAT Radio Mode Antenna Aiming SIRIUS Parental Lock 200kHz/10kHz SIRIUS SIRIUS ID - - - - - - - - - - - - Satellite Terrestrial SIRIUS Antenna Aiming

SIRIUS Satellite Radio Messages The following messages may appear while using SIR- IUS Satellite Radio. ❑ACQUIRING SIGNAL The SiriusConnect receiver is acquiring the signal or no signal is present. Make sure the SiriusConnect Home tuner is connected properly and that there are no obstacles nearby. ❑ANTENNA ERROR Make sure the SiriusConnect Home tuner is con- nected properly. ❑SUBSCRIPTION UPDATED Displayed while your subscription is being updated. No operations can be performed until this message has cleared. ❑UPDATING CHANNELS XXX% Displayed while the channel map is being updated. Wait until the updating is complete. ❑SIRIUS UPDATING Displayed while the SiriusConnect receiver’s firm- ware is being updated. ❑INVALID CHANNEL Displayed if you select an unavailable channel. ❑CALL SIRIUS Displayed when you select a channel to which you are not subscribed. Call SIRIUS if you want to sub- scribe. ❑CHECK SIRIUS TUNER Displayed if the SiriusConnect receiver is not con- nected. Make sure the SiriusConnect receiver is con- nected properly, and make sure its AC adapter is plugged in.

RDS only works in areas where RDS broadcasts are available. When tuned into an RDS station, the RDS indicator appears. ■What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is avail- able in most European countries. Many FM stations use it these days. In addition to displaying text information, RDS can also help you find radio stations by type (e.g., news, sport, rock, etc.). The AV receiver supports four types of RDS informa- tion: PS (Program Service) When tuned to an RDS station that’s broadcasting PS information, the station’s name will be displayed. Press- ing the [Display] button will display the frequency for 3 seconds. RT (Radio Text) When tuned to an RDS station that’s broadcasting text information, the text will be shown on the display (see page 83). PTY (Program Type) This allows you to search for RDS radio stations by type (see page 83). TP (Traffic Program) This allows you to search for RDS radio stations that broadcast traffic information (see page 83). Notes: • In some cases, the text characters displayed on the AV receiver may not be identical to those broadcast by the radio station. Also, unexpected characters may be dis- played when unsupported characters are received. This is not a malfunction. • If the signal from an RDS station is weak, RDS data may be displayed intermittently or not at all. RDS Program Types (PTY) Using RDS (Australian models) RDS indicator Type Display None None News reports News Current affairs Affairs Information Info Sport Sport Education Educate Drama Drama Culture Culture Science and technology Science Varied Varied Pop music Pop M Rock music Rock M Middle of the road music Easy M Light classics Light M Serious classics Classics Other music Other M Weather Weather Finance Finance Children’s programmes Children Social affairs Social Religion Religion Phone in Phone In Travel Travel Leisure Leisure Jazz music Jazz Country music Country National music Nation M Oldies music Oldies Folk music Folk M Documentary Document Alarm test TEST Alarm Alarm!

When tuned to an RDS station that’s broadcasting text information, the text can be displayed. Displaying Radio Text (RT) Notes: • The message “Waiting” may appear while the AV receiver waits for the RT information. • If the message “No Text Data” appears on the display, no RT information is available. Finding Stations by Type (PTY) You can search for radio stations by type. Listening to Traffic News (TP) You can search for stations that broadcast traffic news. Press the [RT/PTY/TP] button once. The RT information scrolls across the display. 1 Press the [RT/PTY/TP] button twice. The current program type appears on the display. 2 Use the Preset [e]/[r] buttons to select the type of program you want. See the table on page 82. RT/PTY/TP RT/PTY/TP Enter Preset e/r 3 To start the search, press [Enter]. The AV receiver searches until it finds a station of the type you specified, at which point it stops briefly before con- tinuing with the search. 4 When a station you want to listen to is found, press [Enter]. If no stations are found, the message “Not Found” appears. 1 Press the [RT/PTY/TP] button three times. If the current radio station is broadcast- ing TP (Traffic Program), “[TP]” will appear on the display, and traffic news will be heard as and when it’s broad- cast. If “TP” without square brackets appears, this means that the station is not broadcasting TP. 2 To locate a station that is broad- casting TP, press [Enter]. The AV receiver searches until it finds a station that’s broadcasting TP. If no stations are found, the message “Not Found” appears. RT/PTY/TP Enter

With the UP-A1 Dock (sold separately), you can easily play the music, photo, or movie stored on your Apple iPod through the AV receiver and enjoy great sound. You can use the AV receiver’s remote controller to operate your iPod. For information about which iPod models are sup- ported by the UP-A1 Dock, see the UP-A1 Dock instruction manual. Note: Before using the UP-A1 Dock, update your iPod with the latest software, available from the Apple Web site. ■Basic Operation Note: The AV receiver may take several seconds to startup, so you might not hear the first few seconds of the first song. • Auto Power On Function If you start iPod playback while the AV receiver is on Standby, the AV receiver will automatically turn on and select your iPod as the input source. • Direct Change Function If you start iPod playback while listening to another input source, the AV receiver will automatically select your iPod as the input source. • Using the AV receiver’s Remote Controller You can use the AV receiver’s remote controller to control basic iPod functions. Operating Notes: • Functionality depends on your iPod model and gener- ation. • Before selecting a different input source, stop iPod playback to prevent the AV receiver from selecting the iPod input source by mistake. • If any accessories are connected to your iPod, the AV receiver may not be able to select the input source properly. • While your iPod is in the UP-A1 Dock, its volume control has no effect. If you adjust your iPod models volume control while it’s in the UP-A1 Dock, make sure it’s not set too high before you reconnect your headphones. • The Auto Power On function will not work if you set your iPod in the UP-A1 Dock while it is playing. • When Zone 2, 3 or 4 is turned on, you can’t use Auto Power On and Direct Change functions. ■Using Your iPod models Alarm Clock You can use your iPod models Alarm Clock function to automatically turn on your iPod and the AV receiver at a specified time. The AV receiver’s input source will auto- matically be set to the [Port] selector. Notes: • To use this function, your iPod must be in the UP-A1 Dock, and the UP-A1 Dock must be connected to the AV receiver. • When you use this function, be sure to set the AV receiver’s volume control to a suitable level. • The AV receiver may take several seconds to startup, so you might not hear the first few seconds of the first song. • When Zone 2, 3 or 4 is turned on, you can’t use this function. • You cannot use this function for sound effects on your iPod. ■Charging Your iPod models Battery The UP-A1 Dock charges your iPod models battery while your iPod is in the UP-A1 Dock and connected to the UNIVERSAL PORT jacks on the AV receiver. While your iPod is seated in the UP-A1 Dock, its battery will be charged when the AV receiver is set to “On” or “Standby”. Note: When UP-A1 Dock that seated iPod is connected, the power consumption on standby mode slightly increases. About the UP-A1 Dock For the latest information on the Dock, see the Onkyo Web site at: http://www.onkyo.com Compatible iPod models Function Overview Dock connector iPod adapter

By pressing the Remote Mode button that’s been pro- grammed with the remote control code for your Dock, you can control your iPod in the Dock with the following buttons. The [Port] button is preprogrammed with the remote control code for controlling a Dock with Universal Port connector. For details on entering a remote control code, see page 150. When Using a Dock with Universal Port connector: • Connect the Dock to the UNIVERSAL PORT jack. • See the Dock’s instruction manual for more informa- tion. You can control your iPod when “Port” is selected as the input source. Notes: • With some iPod models and generations, certain but- tons may not work as expected. • For detailed operation of the iPod, please refer to the instruction manual. a Arrow [q]/[w] and Enter buttons Used to navigate menus and select items. b Previous [7] button Restarts the current song. Press it again to select the previous song. c Fast Reverse [5] button Press and hold to fast reverse. d Pause [3] button Pauses playback. Press it again to start playback. e Repeat button Used with the repeat function. f Display button Select Standard or Extended mode*1. g Muting button (66) Mutes or unmutes the AV receiver. h Album +/– button Selects the next or previous album. i VOL [q]/[w] button (64) Adjusts the volume of the AV receiver. j Playlist [e]/[r] buttons Selects the previous or next playlist on the iPod. k Return button Exits the menu or returns to the previous menu. l Play [1] button Starts playback. If the component is off, it will turn on automatically. m Next [6] button Selects the next song. n Fast Forward [4] button Press and hold to fast forward. o Stop [2] button Stops playback and displays a menu. p Random button Used with the shuffle function. *1 Standard mode Nothing is displayed on your TV and you navigate and select your contents by using your iPod’s display. Only this mode can playback the video. Extended mode Playlists (artists, albums, songs, and so on) are displayed on your TV, and you can navigate and select your music while looking at your TV. Notes: • In Extended mode, the playback will be continued even if the AV receiver is turned off. • In Extended mode, you cannot operate your iPod directly. • In Extended mode, it may take some time to acquire the contents. • In Extended mode, video contents can not display on your TV. Controlling iPod n m k l p o f h i j d b c a g e Press [Port] button first.

Status messages ❏PORT Reading The AV receiver is checking the connection with the dock. ❏PORT Not Support The AV receiver do not support the connected dock. ❏PORT UP-A1 UP-A1 Dock is connected. Notes: • The AV receiver displays the message “UP-A1” for several seconds after recognizing the UP-A1. • When the status message is not displayed on the AV receiver’s display, check the connection to your iPod.

source to a component with recording capability, and how to record audio and video from different sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected DVDs cannot be recorded. • Sources connected to a digital input cannot be recorded. Only analog inputs can be recorded. • DTS signals will be recorded as noise, so don’t attempt analog recording of DTS CDs or LDs. AV Recording Audio sources can be recorded to a recorder (e.g., cas- sette deck, CDR, MD) connected to the TV/TAPE OUT jack. Video sources can be recorded to a video recorder (e.g., VCR, DVD recorder) connected to the VCR/DVR OUT jack. See pages 29 to 44 for hookup information. Recording Separate AV Sources Here you can record audio and video from completely separate sources, allowing you to overdub audio onto your video recordings. This function takes advantage of the fact that when an audio-only input source (i.e., TV/ Tape, Tuner, CD or Phono) is selected, the video input source remains unchanged. In the following example, audio from the CD player con- nected to the CD IN, and video from the camcorder con- nected to the AUX1 Input Video jack are recorded by the VCR connected to the VCR/DVR OUT jacks. 1 Use the input selector buttons to select the source that you want to record. You can watch the source while record- ing. The AV receiver’s Master Volume control has no effect on recording. 2 On your recorder, start record- ing. 3 On the source component, start playback. If you select another input source dur- ing recording, that input source will be recorded. 1 Prepare the camcorder and CD player for playback. 2 Prepare the VCR for recording. 3 Press the [AUX1] input selector button. 4 Press the [CD] input selector button. This selects the CD player as the audio source, but leaves the camcorder as the video source. 5 Start recording on the VCR and start play- back on the camcorder and CD player. The video from the camcorder and the audio from the CD player are recorded by the VCR. Camcorder VCR CD player video signal audio signal

See “About the Listening Modes” on page 96 for detailed information about the listening modes. Selecting on the AV receiver ■Listening Mode buttons [Movie/TV] button This button selects the listening modes intended for use with movies and TV. [Music] button This button selects the listening modes intended for use with music. [Game] button This button selects the listening modes intended for use with video games. Selecting with the Remote Controller ■Listening Mode buttons [Movie/TV] button This button selects the listening modes intended for use with movies and TV. [Music] button This button selects the listening modes intended for use with music. [Game] button This button selects the listening modes intended for use with video games. [THX] button This button selects the THX listening modes. Selecting Listening Modes • The Dolby Digital and DTS listening modes can only be selected if your DVD player is con- nected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI). • The listening modes you can select depend on the format of the input signal. To check the for- mat, see “Displaying Source Information” on page 65. • While a pair of headphones is connected, you can only select the Mono, Direct, or Stereo lis- tening mode. Listening Mode Remote controller Press the [Receiver] button, and then press the Listening Mode button repeatedly to select the listening mode. Movie/TV Music THX Game

Mono/Multiplex Sources ✔: Available Listening Modes Notes: *1 For 7ch output, output can be switched between Front high or Front wide speakers by pressing the [SP Layout] button (depending on the “Speaker Configuration” setting (see page 102)). *2 For 9ch output, output can be switched between the combination of Surround back and Front high, or Surround back and Front wide speakers by pressing the [SP Layout] button. • Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192kHz. • The listening modes cannot be selected with some source formats. Listening Modes Available for Each Source Format The Speaker layout illustration shows which speakers are set to active in the “Speaker Configu- ration” setting (see page 102). The Listening Mode button illus- tration shows that listening modes can be selected. Listening Mode Button Speaker layout Direct ✔ ✔ ✔ ✔ Stereo ✔ ✔ ✔ ✔ Mono ✔ ✔ ✔ ✔ Orchestra ✔ ✔*1*2 Unplugged ✔ ✔*1*2 Studio-Mix ✔ ✔*1*2 TV Logic ✔ ✔*1*2 Game-RPG ✔ ✔*1*2 Game-Action ✔ ✔*1*2 Game-Rock ✔ ✔*1*2 Game-Sports ✔ ✔*1*2 All Ch Stereo ✔ ✔ ✔*1*2 Full Mono ✔ ✔ ✔*1*2 T-D (Theater- Dimensional) ✔ ✔ ✔ ✔ FL LW LH C RH RW FR SR SBR SBL SL SW LH RH SBR SBL FL FR LW RW C SL SR SW C C : Front left speaker : Center speaker : Surround left speaker : active in the speaker settings : non-active in the speaker settings : Front right speaker : Subwoofer : Surround right speaker : Surround back right speaker : Surround back left speaker : Front high left speaker : Front high right speaker : Front wide left speaker : Front wide right speaker LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW *1 *1 *2 *2 *1 *1 *2 *2 *2 *2

Stereo Source (1/2) ✔: Available Listening Modes Listening Mode Button Speaker layout Direct ✔ ✔ ✔ ✔ Stereo ✔ ✔ ✔ ✔ Mono ✔ ✔ ✔ ✔ PLII/PLIIx Movie*3 ✔ ✔ ✔ PLII/PLIIx Music*3 ✔ ✔ ✔ PLII/PLIIx Game*3 ✔ ✔ ✔ PLIIz Height ✔ Neo:6 Cinema ✔ ✔ ✔ Neo:6 Music ✔ ✔ ✔ Neural Surround ✔ ✔ ✔ Neural Digital Music ✔ ✔ ✔ PLII/PLIIx Movie*3 THX Cinema ✔ ✔ PLII/PLIIx Movie Audyssey DSX*4 ✔ PLllz Height THX Cinema ✔ Neo:6 Cinema THX Cinema ✔ ✔ Neo:6 Cinema Audyssey DSX*4 ✔ Neural THX Cinema ✔ ✔ PLII/PLIIx Music*3 THX Music ✔ ✔ PLII/PLIIx Music Audyssey DSX*4 ✔ PLllz Height THX Music ✔ Neo:6 Music THX Music ✔ ✔ Neo:6 Music Audyssey DSX*4 ✔ Neural Digital Music THX Music ✔ ✔ LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW *1 *1 *2 *2 *1 *1 *2 *2 *2 *2

Stereo Source (2/2) ✔: Available Listening Modes Notes: *1 For 7ch output, output can be switched between Front high or Front wide speakers by pressing the [SP Layout] button (depending on the “Speaker Configuration” setting (see page 102)). *2 For 9ch output, output can be switched between the combination of Surround back and Front high, or Surround back and Front wide speakers by pressing the [SP Layout] button. *3 If there are no surround back speakers, or Powered Zone 3 is being used, Dolby Pro Logic II is used. *4 • This listening mode can be selected only when all the following conditions are satisfied: a. Center speaker is connected to the AV receiver. b. Either of Front High speakers or Front Wide speakers is connected to the AV receiver. • Output can be switched between Front high or Front wide speakers by pressing the [SP Layout] button (depending on the “Speaker Configuration” setting (see page 102)). • Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192kHz. • The listening modes cannot be selected with some source formats. Listening Mode Button Speaker layout PLII/PLIIx Game*3 THX Games ✔ ✔ PLII/PLIIx Game Audyssey DSX*4 ✔ PLllz Height THX Games ✔ Neural THX Games ✔ ✔ PLII Game THX Ultra2 Games ✔ PLIIz Height THX Ultra2 Games ✔ Orchestra ✔ ✔*1*2 Unplugged ✔ ✔*1*2 Studio-Mix ✔ ✔*1*2 TV Logic ✔ ✔*1*2 Game-RPG ✔ ✔*1*2 Game-Action ✔ ✔*1*2 Game-Rock ✔ ✔*1*2 Game-Sports ✔ ✔*1*2 All Ch Stereo ✔ ✔ ✔*1*2 Full Mono ✔ ✔ ✔*1*2 T-D (Theater- Dimensional) ✔ ✔ ✔ ✔ LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW *1 *1 *2 *2 *1 *1 *2 *2 *2 *2

5.1 channel Sources (1/2) ✔: Available Listening Modes Listening Mode Button Speaker layout Direct ✔ ✔ ✔ ✔ Stereo ✔ ✔ ✔ ✔ Mono ✔ ✔ ✔ ✔ DolbyDigital/ DolbyDigital Plus/TrueHD/ Multichannel/ DTS/ DTS 96/24*5/ DTS Express/ DTS-HD High Resolution Audio/DTS-HD Master Audio/ DSD*3 ✔ ✔ ✔ PLIIx Movie ✔ PLIIx Music ✔ PLIIz Height ✔ DolbyEX ✔ DolbyEX Audyssey DSX*4 ✔ Neo:6 ✔ Neo:6 Audyssey DSX*4 ✔ Neural Surround ✔ Audyssey DSX*4 ✔ THX Cinema ✔ ✔ PLIIx Movie THX Cinema ✔ PLIIx Movie Audyssey DSX*4 ✔ PLIIz Height THX Cinema ✔ Neo:6 THX Cinema ✔ Neural THX Cinema ✔ THX Music ✔ ✔ LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW *1 *1 *2 *2 *1 *1 *2 *2 *2 *2

5.1 channel Sources (2/2) ✔: Available Listening Modes Listening Mode Button Speaker layout PLIIx Music THX Music ✔ PLIIx Music Audyssey DSX*4 ✔ PLIIz Height THX Music ✔ Neo:6 THX Music ✔ Neural THX Music ✔ THX Games ✔ ✔ PLIIx Height THX Games ✔ Neo:6 THX Games ✔ Neural THX Games ✔ THX Surround EX ✔ THX Ultra2 Cinema ✔ PLIIz THX Ultra2 Cinema ✔ THX Ultra2 Music ✔ PLIIz THX Ultra2 Music ✔ THX Ultra2 Games ✔ PLIIz THX Ultra2 Games ✔ Orchestra ✔ ✔*1*2 Unplugged ✔ ✔*1*2 Studio-Mix ✔ ✔*1*2 TV Logic ✔ ✔*1*2 Game-RPG ✔ ✔*1*2 Game-Action ✔ ✔*1*2 Game-Rock ✔ ✔*1*2 Game-Sports ✔ ✔*1*2 All Ch Stereo ✔ ✔ ✔*1*2 Full Mono ✔ ✔ ✔*1*2 T-D (Theater- Dimensional) ✔ ✔ ✔ ✔ LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW *1 *1 *2 *2 *1 *1 *2 *2 *2 *2

Notes: *1 For 7ch output, output can be switched between Front high or Front wide speakers by pressing the [SP Layout] button (depending on the “Speaker Configuration” setting (see page 102)). *2 For 9ch output, output can be switched between the combination of Surround back and Front high, or Surround back and Front wide speakers by pressing the [SP Layout] button. *3 AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better sound according to the player. In that case, set the output setting on the player side to PCM. *4 • This listening mode can be selected only when all the following conditions are satisfied: a. Center speaker is connected to the AV receiver. b. Either of Front High speakers or Front Wide speakers is connected to the AV receiver. • Output can be switched between Front high or Front wide speakers by pressing the [SP Layout] button (depending on the “Speaker Configuration” setting (see page 102)). *5 Depending on the input source, DTS is used. • Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192kHz. • The listening modes cannot be selected with some source formats.

7.1 channel Sources ✔: Available Listening Modes Listening Mode Button Speaker layout Direct ✔ ✔ ✔ ✔ Stereo ✔ ✔ ✔ ✔ Mono ✔ ✔ ✔ ✔ Multichannel/ DolbyDigital Plus/TrueHD/ DTS-HD High Resolution Audio/DTS-HD Master Audio/ DTS-ES Discrete*5/ DTS-ES Matrix*5 ✔ ✔ ✔*3 PLIIz Height ✔ Audyssey DSX*4 ✔ THX Cinema ✔ ✔ PLIIz Height THX Cinema ✔ THX Music ✔ ✔ PLIIz Height THX Music ✔ THX Games ✔ ✔ PLIIz Height THX Games ✔ Orchestra ✔ ✔*1*2 Unplugged ✔ ✔*1*2 Studio-Mix ✔ ✔*1*2 TV Logic ✔ ✔*1*2 Game-RPG ✔ ✔*1*2 Game-Action ✔ ✔*1*2 Game-Rock ✔ ✔*1*2 Game-Sports ✔ ✔*1*2 All Ch Stereo ✔ ✔ ✔*1*2 Full Mono ✔ ✔ ✔*1*2 T-D (Theater- Dimensional) ✔ ✔ ✔ ✔ LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW LH RH SBR SBL FL FR LW RW C SL SR SW *1 *1 *2 *2 *1 *1 *2 *2 *2 *2

Notes: *1 For 7ch output, output can be switched between Front high or Front wide speakers by pressing the [SP Layout] button (depending on the “Speaker Configuration” setting (see page 102)). *2 For 9ch output, output can be switched between the combination of Surround back and Front high, or Surround back and Front wide speakers by pressing the [SP Layout] button. *3 Based on the audio channels contained in the source, the corresponding speakers will output the sound. *4 • This listening mode can be selected only when all the following conditions are satisfied: a. Center speaker is connected to the AV receiver. b. Either of Front High speakers or Front Wide speakers is connected to the AV receiver. • Output can be switched between Front high or Front wide speakers by pressing the [SP Layout] button (depending on the “Speaker Configuration” setting (see page 102)). *5 If there are no surround back speakers, DTS is used. • Available sampling rate for PCM input signal is 32/44.1/48/88.2/96/176.4/192kHz. • The listening modes cannot be selected with some source formats. The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Direct In this mode, audio from the input source is output directly with minimal processing, providing high-fidel- ity reproduction. All of the source’s audio channels are output as they are. Stereo Sound is output by the front left and right speakers and subwoofer. Mono Use this mode when watching an old movie with a mono soundtrack, or use it with the foreign language soundtracks recorded in the left and right channels of some movies. It can also be used with DVDs or other sources containing multiplexed audio, such as karaoke DVDs. Multichannel This mode is for use with PCM multichannel sources. Dolby Pro Logic IIx Dolby Pro Logic II Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It provides a very natural and seamless surround-sound experience that fully envelops the listener. As well as music and movies, video games can also benefit from the dramatic spatial effects and vivid imaging. If you’re not using any surround back speakers, Dolby Pro Logic II will be used instead of Dolby Pro Logic IIx. • Dolby PLIIx Movie Use this mode with any stereo or Dolby Surround (Pro Logic) movie (e.g., TV, DVD, VHS). • Dolby PLIIx Music Use this mode with any stereo or Dolby Surround (Pro Logic) music source (e.g., CD, radio, cassette, TV, VHS, DVD). • Dolby PLIIx Game Use this mode with video games, especially those that bear the Dolby Pro Logic II logo. Dolby Pro Logic IIz Height Dolby Pro Logic IIz Height is designed to more effec- tively use existing program material when height chan- nel speaker outputs are present. Dolby Pro Logic IIz Height can be used to upmix a variety of sources from movies and music, but are particularly well-suited to upmix game content. Dolby Digital Use this mode with DVDs that bear the Dolby Digital logo, and Dolby Digital TV broadcasts. This is the most common digital surround-sound format, and it’ll put you right in the middle of the action, just like being in a movie theater or concert hall. Audyssey Dynamic Surround Expansion™ Audyssey Dynamic Surround Expansion™ is a scalable system that adds new speakers to improve surround impression. Starting with a 5.1 system Dynamic Sur- round Expansion first adds Wide channels for the biggest impact on envelopment. Research in human hearing has proven that information from the Wide channels is much more critical in the presentation of a realistic soundstage than then Back Surround channels found in traditional 7.1 systems. Dynamic Surround Expansion then creates a pair of Height channels to reproduce the next most important acoustical and perceptual cues. In addition to these new Wide and Height channels, Dynamic Sur- round Expansion applies Surround Envelopment Pro- cessing to enhance the blend between the front and surround channels. About the Listening Modes

5.1-channel source + Dolby EX These modes expand 5.1-channel sources for 6.1/7.1- channel playback. They’re especially suited to Dolby EX soundtracks that include a matrix-encoded surround back channel. The additional channel adds an extra dimension and provides an enveloping surround sound experience, perfect for rotating and fly-by sound effects. Dolby Digital Plus Developed for use with HDTV, including the new video disc formats Blu-ray and HD DVD, this is the latest mul- tichannel audio format from Dolby. It supports up to 7.1 channels with 48 kHz sampling rate. Dolby TrueHD Designed to take full advantage of the additional storage space offered by the new Blu-ray and HD DVD disc for- mats, this new Dolby format offers up to 7.1 discrete channels of digital audio with 48/96 kHz, up to 5.1-chan- nels with 192 kHz sampling rate. 5.1-channel source + Dolby PLIIx Music These modes use the Dolby Pro Logic IIx Music mode to expand 5.1-channel sources for 6.1/7.1-channel play- back. 5.1-channel source + Dolby PLIIx Movie These modes use the Dolby Pro Logic IIx Movie mode to expand 5.1-channel sources for 7.1-channel playback. DTS The DTS digital surround-sound format supports up to 5.1 discrete channels and uses less compression for high- fidelity reproduction. Use it with DVDs and CDs that bear the DTS logo. DTS 96/24 This mode is for use with DTS 96/24 sources. This is high-resolution DTS with a 96 kHz sampling rate and 24-bit resolution, providing superior fidelity. Use it with DVDs that bear the DTS 96/24 logo. DTS-ES Discrete This mode is for use with DTS-ES Discrete soundtracks, which use a discrete surround back channel for true 6.1/ 7.1-channel playback. The seven totally separate audio channels provide better spatial imaging and 360-degree sound localization, perfect for sounds that pan across the surround channels. Use it with DVDs that bear the DTS- ES logo, especially those with a DTS-ES Discrete soundtrack. DTS-ES Matrix This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-encoded back-channel for 6.1/7.1- channel playback. Use it with DVDs that bear the DTS- ES logo, especially those with a DTS-ES Matrix soundtrack. DTS Neo:6 This mode expands any 2-channel source for up to 7.1- channel playback. It uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, provid- ing a very natural and seamless surround sound experi- ence that fully envelops the listener. • Neo:6 Cinema Use this mode with any stereo movie (e.g., TV, DVD, VHS). • Neo:6 Music Use this mode with any stereo music source (e.g., CD, radio, cassette, TV, VHS, DVD). 5.1-channel source + Neo:6 This mode uses Neo:6 to expand 5.1-channel sources for 6.1/7.1-channel playback. DTS-HD High Resolution Audio Developed for use with HDTV, including the new video disc formats Blu-ray and HD DVD, this is the latest mul- tichannel audio format from DTS. It supports up to 7.1 channels with 96 kHz sampling rate. DTS-HD Master Audio Designed to take full advantage of the additional storage space offered by the new Blu-ray and HD DVD disc for- mats, this new DTS format offers up to 7.1 discrete chan- nels of digital audio with 48/96 kHz, up to 5.1-channels with 192 kHz sampling rate. DTS Express This format supports up to 5.1 channels and a lower sam- pling rate of 48 kHz. Applications include interactive audio and commentary encoding for HD DVD Sub Audio and Blu-ray Secondary Audio. Also broadcast and media servers. Neural Digital Music Neural Digital Music is a new surround mode specifi- cally designed to enhance the playback of compressed digital music content. It provides listeners with an expanded sound stage and clean surround experience, even with compressed audio sources such as MP3s and Internet streams. DSD DSD stands for Direct Stream Digital and is the format used to store digital audio on Super Audio CDs (SACD). This mode can be used with Super Audio CDs that fea- ture multichannel audio.

THX Founded by George Lucas, THX develops stringent stan- dards that ensure movies are reproduced in movie the- aters and home theaters just as the director intended. THX Modes carefully optimize the tonal and spatial characteristics of the soundtrack for reproduction in the home-theater environment. They can be used with 2- channel matrixed and multichannel sources. Surround back speaker output depends on the source material and the selected listening mode. • THX Cinema THX Cinema mode corrects theatrical soundtracks for playback in a home theater environment. In this mode, THX Loudness Plus is configured for cinema levels and Re-EQ, Timbre Matching, and Adaptive Decorrelation are active. • THX Music THX Music mode is tailored for listening to music, which is typically mastered at significantly higher levels than movies. In this mode, THX Loudness Plus is configured for music playback and only Tim- bre Matching is active. • THX Games THX Games mode is meant for spatially accurate playback of game audio, which is often mixed simi- larly to movies but in a smaller environment. THX Loudness Plus is configured for game audio levels, with Timbre Matching active. • THX Ultra2 Cinema This mode expands 5.1-channel sources for 7.1- channel playback. It does this by analyzing the com- position of the surround source, optimizing the ambient and directional sounds to produce the sur- round back channel output. • THX Ultra2 Music This mode is designed for use with music. It expands 5.1-channel sources for 7.1-channel playback. • THX Ultra2 Games This mode is designed for use with video games. It can expand 5.1-channel sources for 6.1/7.1-channel playback. • THX Surround EX This mode expands 5.1-channel sources for 6.1/7.1- channel playback. It’s especially suited to Dolby Digital EX sources. THX Surround EX, also known as Dolby Digital Surround EX, is a joint develop- ment between Dolby Laboratories and THX Ltd. Neural Surround Neural Surround employs psychoacoustic frequency domain processing, which allows delivery of a more detailed sound stage, with superior channel separation and localization of audio elements. The Neural Surround modes can expand any 2-channel stereo source for 5.1- or 7.1-channel playback, respectively. Use them with CD, radio, cassette, TV, VHS, DVD, and other 2-channel stereo sources, including video games. Neural Surround can also be used by broadcasters to encode and transmit surround-sound content over a stereo signal, which lis- teners can enjoy as either surround sound or normal ste- reo. Onkyo Original DSP Modes Orchestra Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall. Unplugged Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the front stereo image, giving the impression of being right in front of the stage. Studio-Mix Suitable for rock or pop music, listening to music in this mode creates a lively sound field with a powerful acous- tic image, like being at a club or rock concert. TV Logic This mode adds realistic acoustics to TV shows pro- duced in a TV studio, surround effects to the entire sound, and clarity to voices. Game-RPG Use this mode when playing role playing game discs. Game-Action Use this mode when playing action game discs. Game-Rock Use this mode when playing rock game discs. Game-Sports Use this mode when playing sports game discs. All Ch Stereo Ideal for background music, this mode fills the entire lis- tening area with stereo sound from the front, surround, and surround back speakers. Full Mono In this mode, all speakers output the same sound in mono, so the sound you hear is the same regardless of where you are within the listening room. T-D (Theater-Dimensional) With this mode you can enjoy a virtual surround sound even with only two or three speakers. This works by con- trolling how sounds reach the listener’s left and right ears. Good results may not be possible if there’s too much reverb, so we recommend that you use this mode in an environment with little or no natural reverb.

various settings. Settings are organized into nine categories on the main menu, most containing a submenu. Onscreen Setup Menus 1. Input/Output Assign 2. Speaker Setup 3. Audio Adjust 4. Source Setup 5. Listening Mode Preset 6. Miscellaneous 7. Hardware Setup 8. Remote Controller Setup 9. Lock Setup Menu 1. Speaker Settings 2. Speaker Configuration 3. Speaker Distance 4. Level Calibration 5. Equalizer Settings 6. THX Audio Setup 1. Multiplex/Mono 2. Dolby 3. DTS 4. Audyssey 5. Theater-Dimensional 6. LFE Level 7. Direct 1. DVD/BD 2. VCR/DVR 3. CBL/SAT 4. GAME 5. AUX1 1. Remote Mode Setup 2. Activities Setup Lock Unlocked 1. IntelliVolume 2. A/V Sync 3. Name Edit 4. Picture Adjust 7. Hardware Setup 1. Remote ID 2. Multi Zone 3. Tuner 4. HDMI 5. Network 6. Firmware Update 8. Remote Controller Setup 9. Lock Setup 5. Listening Mode Preset 4. Source Setup 3. Audio Adjust 2. Speaker Setup 1. Input/Output Assign DVD/BD 1. Monitor Out 2. HDMI Input 3. Component Video Input 4. Digital Audio Input 5. Analog Audio Input 6. Gamma Curve 6. Miscellaneous 1. Volume Setup 2. OSD Setup 3. 12V Trigger A Setup 4. 12V Trigger B Setup 5. 12V Trigger C Setup Submenus Main menu pages 102–105 pages 106–109 pages 110–114 page 115 pages 116–117 pages 117–121 page 122 page 56 page 54 page 132 page 142 page 148 page 159 page 49 page 51 page 52 page 53 pages 100–101 page 54 page 145

Note: This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. Input/Output Assign 1 Press the [Receiver] button followed by the [Setup] button. The main menu appears onscreen. If the main menu doesn’t appear, make sure the appropriate external input is selected on your TV. 2 Use the Up and Down [q]/[w] buttons to select “1. Input/Output Assign”, and then press [Enter]. 3 Use the Up and Down [q]/[w] buttons to select the submenu, and then press [Enter]. 4 Use the Up and Down [q]/[w] buttons to select setting, and then use the Left and Right [e]/[r] buttons to set them. 5 When you’ve finished, press the [Setup] button. The setup menu closes. Monitor Out Monitor Out Resolution See “Monitor Out Setup” on page 49. Brightness –50 to +50 (default: 0) With this setting you can adjust the picture brightness. “–50” is the darkest. “+50” is the brightest. Contrast –50 to +50 (default: 0) With this setting you can adjust contrast. “–50” is the least. “+50” is the greatest. Hue –20 to +20 (default: 0) With this setting you can adjust the red/green balance. “–20” is the strongest green. “+20” is the strongest red. Saturation –50 to +50 (default: 0) With this setting you can adjust saturation. “–50” is the weakest color. “+50” is the strongest color. Red Brightness –50 to +50 (default: 0) With this setting you can adjust the picture red brightness. “–50” is the darkest. “+50” is the brightest. Red Contrast –50 to +50 (default: 0) With this setting you can adjust red contrast. “–50” is the least. “+50” is the greatest. Green Brightness –50 to +50 (default: 0) With this setting you can adjust the picture green brightness. “–50” is the darkest. “+50” is the brightest. Green Contrast –50 to +50 (default: 0) With this setting you can adjust green contrast. “–50” is the least. “+50” is the greatest. Blue Brightness –50 to +50 (default: 0) With this setting you can adjust the picture blue brightness. “–50” is the darkest. “+50” is the brightest. Blue Contrast –50 to +50 (default: 0) With this setting you can adjust blue contrast. “–50” is the least. “+50” is the greatest. HDMI Input See “HDMI Input Setup” on page 51.