Intel D915GVWB Product Manual

September 2004 If an FCC declaration of conformity marking is present on the board, the following statement applies: FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions related to the EMC performance of this product, contact: Intel Corporation 5200 N.E. Elam Young Parkway Hillsboro, OR 97124 1-800-628-8686 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the user’s authority to operate the equipment. Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par le ministére des Communications du Canada. Disclaimer Information in this document is provided in connection with Intel® products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel’s Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. Desktop Board D915GVWB may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be obtained from Intel Corporation by going to the World Wide Web site at: http://www.intel.com/ or by calling 1-800-548-4725. Intel, Pentium, and Celeron are registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. * Other names and brands may be claimed as the property of others. Copyright © 2004, Intel Corporation. All rights reserved.

regulatory requirements for Intel® Desktop Board D915GVWB. Intended Audience The Product Guide is intended for technically qualified personnel. It is not intended for general audiences. Information Layout The chapters in this Product Guide are arranged as follows: 1 Desktop Board Features: a summary of product features 2 Installing and Replacing Desktop Board Components: instructions on how to install the desktop board and other hardware components 3 BIOS: instructions on how to update the BIOS A Error Messages and Indicators: information about BIOS error messages and beep codes B Regulatory Compliance: safety and EMC regulations, product certification Conventions The following conventions are used in this manual: WARNING Warnings indicate conditions that, if not observed, can cause personal injury. CAUTION Cautions warn the user about how to prevent damage to hardware or loss of data. NOTE Notes call attention to important information.

iv Terminology The table below gives descriptions to some common terms used in the product guide. Term Description GB Gigabyte (1,073,741,824 bytes) GHz Gigahertz (one billion hertz) KB Kilobyte (1024 bytes) MB Megabyte (1,048,576 bytes) Mbit Megabit (1,048,576 bits) MHz Megahertz (one million hertz) Box Contents • Intel Desktop Board • I/O shield • One IDE cable • Two SATA cables (second cable optional) • One diskette drive cable • Quick Reference Guide • Configuration and battery caution statement label • Intel® Express Installer CD-ROM

Manufacturing Option............................................................................................................10 Supported Operating Systems..............................................................................................10 Desktop Board Components.................................................................................................11 Processor..............................................................................................................................13 Main Memory ........................................................................................................................14 Intel® 915GV Express Chipset..............................................................................................14 Graphics Subsystem.............................................................................................................15 Audio Subsystem ..................................................................................................................15 Input/Output (I/O) Controller..................................................................................................16 LAN Subsystem (Optional)....................................................................................................16 LAN Subsystem Software ............................................................................................16 RJ-45 LAN Connector LEDs ........................................................................................16 Hi-Speed USB 2.0 Support ...................................................................................................17 Enhanced IDE Interface........................................................................................................17 Serial ATA.............................................................................................................................17 Expandability.........................................................................................................................17 BIOS......................................................................................................................................18 Serial ATA and IDE Auto Configuration .......................................................................18 PCI and PCI Express Auto Configuration ....................................................................18 Security Passwords......................................................................................................18 Chassis Intrusion...................................................................................................................18 Power Management Features...............................................................................................19 ACPI.............................................................................................................................19 Power Connectors........................................................................................................19 Fan Connectors............................................................................................................19 Fan Speed Control (Intel® Precision Cooling Technology) ..........................................19 Suspend to RAM (Instantly Available PC Technology)................................................20 Resume on Ring ..........................................................................................................21 Wake from USB ...........................................................................................................21 Wake from PS/2 Keyboard/Mouse...............................................................................21 PME# Wakeup Support................................................................................................21 Speaker.................................................................................................................................21 Battery...................................................................................................................................21 Real-Time Clock....................................................................................................................21 2 Installing and Replacing Desktop Board Components Before You Begin..................................................................................................................23 Installation Precautions.........................................................................................................24 Installation Instructions..........................................................................................................24 Ensure Electromagnetic Compatibility (EMC) Compliance ..........................................24 Chassis and Component Certifications........................................................................25 Prevent Power Supply Overload..................................................................................25 Place Battery Marking..................................................................................................25

vi Use Only for Intended Applications..............................................................................26 Installing the I/O Shield .........................................................................................................26 Installing and Removing the Desktop Board.........................................................................27 Installing and Removing a Processor....................................................................................28 Installing a Processor...................................................................................................28 Installing the Processor Fan Heat Sink........................................................................31 Connecting the Processor Fan Heat Sink Cable..........................................................31 Removing the Processor..............................................................................................32 Installing and Removing Memory..........................................................................................32 Installing DIMMs...........................................................................................................34 Removing DIMMs.........................................................................................................35 Connecting the IDE Cable.....................................................................................................36 Connecting the Serial ATA (SATA) Cable.............................................................................37 Connecting Internal Headers ................................................................................................38 Connecting the USB 2.0 Headers................................................................................39 Connecting the Front Panel Header.............................................................................39 Connecting the Front Panel Audio Header ..................................................................39 Connecting to the Flexible 6-Channel Audio System............................................................40 Connecting Fan and Power Cables ......................................................................................41 Connecting Fan Cables................................................................................................41 Connecting Power Cables............................................................................................42 Other Connectors..................................................................................................................44 Setting the BIOS Configuration Jumper Block ......................................................................45 Clearing Passwords ..............................................................................................................46 Back Panel Connectors.........................................................................................................47 Replacing the Battery............................................................................................................48 3 BIOS Updating the BIOS with the Intel® Express BIOS Update Utility ...........................................53 Updating the BIOS with the Iflash Memory Update Utility.....................................................54 Obtaining the BIOS Update File...................................................................................54 Updating the BIOS .......................................................................................................54 Recovering the BIOS ...................................................................................................55 A Error Messages and Indicators BIOS Beep Code...................................................................................................................57 BIOS Error Messages ...........................................................................................................57 B Regulatory Compliance Safety Regulations................................................................................................................59 European Union Declaration of Conformity Statement .........................................................59 Product Ecology Statements.................................................................................................61 EMC Regulations ..................................................................................................................61 Product Certification Markings (Board Level)........................................................................63

2. Location of Standby Power Indicator..............................................................................20 3. Installing the I/O Shield...................................................................................................26 4. Mounting Screw Hole Locations.....................................................................................27 5. Lift Socket Lever.............................................................................................................28 6. Lift the Load Plate and Don’t Touch the Socket Contacts..............................................28 7. Remove the Protective Socket Cover.............................................................................29 8. Remove the Processor from the Protective Processor Cover/Do Not Touch.................29 9. Install Processor.............................................................................................................30 10. Close the Load Plate ......................................................................................................30 11. Connecting the Processor Fan Heat Sink Cable to the Processor Fan Connector........31 12. Dual Configuration Example 1........................................................................................32 13. Dual Configuration Example 2........................................................................................33 14. Dual Configuration Example 3........................................................................................33 15. Installing a DIMM............................................................................................................34 16. Connecting the IDE Cable..............................................................................................36 17. Connecting the Serial ATA Cable...................................................................................37 18. Internal Headers.............................................................................................................38 19. Back Panel Audio Connectors for Flexible 6-Channel Audio System ............................40 20. Location of Fan Headers ................................................................................................41 21. Connecting 2x10 Power Supply Cables .........................................................................42 22. Connecting 2x12 Power Supply Cables .........................................................................43 23. Location of Other Connectors.........................................................................................44 24. Location of the BIOS Configuration Jumper Block .........................................................45 25. Back Panel Connectors..................................................................................................47 26. Removing the Battery.....................................................................................................52 27. F2 Key ............................................................................................................................53 Tables 1. Feature Summary.............................................................................................................9 2. Manufacturing Option .....................................................................................................10 3. Desktop Board D915GVWB Components......................................................................12 4. RJ-45 10/100 Ethernet LAN Connector LEDs................................................................16 5. USB 2.0 Header Signal Names......................................................................................39 6. Front Panel Header Signal Names.................................................................................39 7. Front Panel Audio Header Signal Names.......................................................................39 8. Jumper Settings for the BIOS Setup Program Modes....................................................45 9. BIOS Beep Code............................................................................................................57 10. BIOS Error Messages.....................................................................................................57 11. Safety Regulations .........................................................................................................59 12. EMC Regulations............................................................................................................61 13. Product Certification Markings........................................................................................63

This chapter briefly describes the main features of the Intel® Desktop Board D915GVWB. Table 1 summarizes the major features of the desktop board. Table 1. Feature Summary Form Factor MicroATX (9.60” x 9.60”) Intel Desktop Board D915GVWB Processor • Support for an Intel® Pentium® 4 processor in the LGA775 package • Support for an Intel® Celeron® D processor in the LGA775 package Main Memory • Four 184-pin, 2.5 V SDRAM Dual Inline Memory Module (DIMM) sockets • 400/333 MHz single or dual channel DDR SDRAM interface • Designed to support up to 4 GB of system memory NOTE: For the latest list of tested memory, refer to the Intel World Wide Web site at: http://support.intel.com/support/motherboards/desktop/ Chipset Intel® 915GV Express Chipset consisting of: • Intel® 82915GV Graphics and Memory Controller Hub (GMCH) with Direct Media Interface • Intel® 82801FB I/O Controller Hub (ICH6) Graphics Intel 915GV Express Chipset with Intel® Graphics Media Accelerator 900 Audio • Intel 915GV Express Chipset • Intel® High Definition Audio codec Expansion Capabilities • Two PCI bus add-in card connectors (SMBus routed to slot 2) • One PCI Express* x1 connector Peripheral Interfaces • Up to eight USB 2.0 ports: ⎯ Four ports routed to the back panel ⎯ Four ports routed to two USB headers • Four Serial ATA (SATA) channels, via the ICH6, one device per channel • One IDE interface with ATA-66/100 support (two devices) • One diskette drive interface • One parallel port • One serial port • PS/2* keyboard and mouse ports BIOS • 4 Mbit flash memory • Support for SMBIOS • Intel® Rapid BIOS Boot • Intel® Express BIOS Update continued

10 Table 1. Feature Summary (continued) Power Management • Support for Advanced Configuration and Power Interface (ACPI) • Suspend to RAM (STR) • Wake on USB, PCI, PCI Express, PS/2, LAN, and front panel Hardware Management Hardware monitor with: • Three fan sensing inputs used to monitor fan activity • Remote diode temperature sensing • Intel® Precision Cooling Technology fan speed control that automatically adjusts processor fan speed based on processor temperature and chassis fan speeds based on system temperature • Voltage sensing to detect out of range values Related Links: For more information about Intel Desktop Board D915GVWB, including the Technical Product Specification (TPS), BIOS updates, and device drivers, go to: http://support.intel.com/support/motherboards/desktop/ Manufacturing Option Table 2 shows the manufacturing option for the Desktop Board D915GVWB. Table 2. Manufacturing Option Option Description LAN Intel® 82562EZ 10/100 Mbit/sec Platform LAN Connect (PLC) device with RJ-45 connector Supported Operating Systems The desktop board supports the following operating systems: • Microsoft Windows* XP • Microsoft Windows 2000

11 Desktop Board Components Figure 1 shows the approximate location of the major components on the Desktop Board D915GVWB. OM17366 Line In RJ45 DIMM 0 DIMM 0 Channel A Channel B A H G K J C D E F O M L N B P R Q I B S 82915GV (GMCH) DIMM 1 DIMM 1 Figure 1. Intel Desktop Board D915GVWB Components

12 Table 3. Desktop Board D915GVWB Components Label Description A Front panel audio header (yellow) B Rear chassis fan header (fan speed control) C 12 V processor core voltage connector (2x2) D Processor socket E Processor fan header (4-pin, fan speed control) F Main power connector (2x12) G Diskette drive connector H Primary IDE connector I Battery J Chassis intrusion header K BIOS configuration jumper L Front chassis fan header (fan speed control) M Serial ATA connectors (4) N Alternate power LED header O Front panel header P USB 2.0 headers (black, 2) Q PCI bus add-in card connectors (2) R Speaker S PCI Express x1 connector Related Links: Go to the following links for more information about: • Intel Desktop Board D915GVWB http://www.intel.com/design/motherbd http://support.intel.com/support/motherboards/desktop • Supported processors http://support.intel.com/support/motherboards/desktop • Audio software and utilities http://www.intel.com/design/motherbd • LAN software and drivers http://www.intel.com/design/motherbd

13 Processor CAUTION Failure to use an ATX12V power supply, or not connecting the 12 V (2x2) processor core voltage power supply connector to Desktop Board D915GVWB may result in damage to the desktop board and/or power supply. The Desktop Board D915GVWB supports a single Intel Pentium 4 processor or Intel Celeron D processor in the LGA775 package. The processor is not included with the desktop board and must be purchased separately. The processor connects to the Intel desktop board through the LGA775 socket. The supported processors list for the Desktop Board D915GVWB is located on the web at: http://support.intel.com/support/motherboards/desktop/ Related Links: Go to the following links or pages for more information about: • Supported Intel® processors for the Desktop Board D915GVWB: http://support.intel.com/support/motherboards/desktop/ • Instructions on installing or upgrading the processor, page 28 in Chapter 2. • The location of the power connector, page 41 in Chapter 2.

14 Main Memory NOTE To be fully compliant with all applicable Intel® SDRAM memory specifications, the board should be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. If your memory modules do not support SPD, you will see a notification to this effect on the screen at power up. The BIOS will attempt to configure the memory controller for normal operation. The desktop board supports: • Four 184-pin Double Data Rate (DDR) SDRAM Dual Inline Memory Module (DIMMs) connectors with gold-plated contacts • Unbuffered, non-registered single or double-sided DIMMs • Serial Presence Detect (SPD) memory only • Non-ECC RAM • 2.5 V memory • Memory configuration listed below: ⎯ Up to 1.0 GB utilizing 256 Mb technology ⎯ Up to 4.0 GB utilizing 512Mb or 1 GB technology NOTE System resources (such as PCI and PCI Express) require physical memory address locations that reduce available memory addresses above 3 GB. This may result in less than 4 GB of memory being available to the operating system and applications. Related Links: Go to the following links or pages for more information about: • The latest list of tested memory, http://support.intel.com/support/motherboards/desktop/ • SDRAM specifications, http://www.intel.com/technology/memory/pcsdram/spec/ • Installing memory, page 32 in Chapter 2 Intel® 915GV Express Chipset The Intel 915GV Express Chipset consists of the following devices: • Intel 82915GV Graphics and Memory Controller Hub (GMCH) with Digital Media Interface • Intel 82801FB I/O Controller Hub (ICH6) Related Link: Go to the following link for more information about the Intel 915GV Express Chipset: http://developer.intel.com/design/nav/pcserver.htm

15 Graphics Subsystem The Desktop Board D915GVWB includes the following: • Intel 915GV Express Chipset • Intel Graphics Media Accelerator 900 Audio Subsystem The Desktop Board D915GVWB includes a flexible 6-channel audio subsystem based on an Intel High Definition Audio codec: The audio subsystem features: • Impedance sensing capability for jack re-tasking • S/N (signal-to-noise) ratio: > 90 dB • Power management support for ACPI 2.0 (driver dependent) • Intel 82801FB I/O Controller Hub (ICH6) • Intel High Definition Audio codec • Microphone input that supports: ⎯ Microphone array ⎯ Acoustic Echo (AEC) ⎯ Beam Forming (BF) ⎯ Noise Supression (NX) technology The subsystem includes the following connectors: • Front panel audio connector, including pins for: ⎯ Line out ⎯ Line in • Back panel audio connectors that are configurable through the drivers of the audio devices: ⎯ Line in, or rear left/right out ⎯ Line out, or front left/right out ⎯ Mic in, or center/LFE out Related Links: Go to the following link or pages for more information about: • Audio drivers and utilities http://support.intel.com/support/motherboards/desktop/ • Installing the front panel audio solution, page 39 in Chapter 2 • The location of audio connectors, page Figure 19 on page 40

16 Input/Output (I/O) Controller The super I/O controller features the following: • One serial port • One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port (EPP) support • Serial IRQ interface compatible with serialized IRQ support for PCI systems • PS/2-style mouse and keyboard interfaces • Interface for one 1.2 MB or 1.44 MB diskette drive • Intelligent power management, including a programmable wake up event interface • PCI power management support LAN Subsystem (Optional) The optional LAN, with the Intel 82801FB (ICH6), provides a Fast PCI LAN subsystem. The LAN subsystem provides the following functions: • Basic 10/100 Ethernet LAN (Intel 82562EZ) • Support for RJ-45 connector with status indicator LEDs • Programmable transit threshold • Configurable EEPROM that contains the MAC address LAN Subsystem Software For LAN software and drivers, refer to the D915GVWB link on Intel’s World Wide Web site at: http://support.intel.com/support/motherboards/desktop RJ-45 LAN Connector LEDs Two LEDs are built into the RJ-45 LAN connector. Table 4 describes the LED states when the board is powered up and the 10/100 Ethernet LAN subsystem is operating. Table 4. RJ-45 10/100 Ethernet LAN Connector LEDs LED Color LED State Indicates Off 10 Mbit/sec data rate is selected. Green On 100 Mbit/sec data rate is selected. Off LAN link is not established. On (steady state) LAN link is established. Yellow On (brighter and pulsing) The computer is communicating with another computer on the LAN.

17 Hi-Speed USB 2.0 Support NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. The desktop board supports up to eight USB 2.0 ports via ICH6; four ports routed to the back panel and four routed to two internal USB 2.0 headers. USB 2.0 ports are backward compatible with USB 1.1 devices. USB 1.1 devices will function normally at USB 1.1 speeds. USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer rates. Disabling Hi-Speed USB in BIOS reverts all USB 2.0 ports to USB 1.1 operation. This may be required to accommodate operating systems that do not support USB 2.0. Enhanced IDE Interface The ICH6’s IDE interface handles the exchange of information between the processor and peripheral devices like hard disks, CD-ROM drives, and Iomega Zip* drives inside the computer. The interface supports: • Up to two IDE devices (such as hard drives) • ATAPI-style devices (such as CD-ROM drives) • Older PIO Mode devices • Ultra DMA-33 and ATA-66/100 protocols • Laser Servo (LS-120) drives Serial ATA The desktop board supports four Serial ATA channels via ICH6, connecting one device per channel. Expandability The desktop board supports the following: • One PCI Express x1 add-in card • Two PCI add-in cards

18 BIOS The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI/PCI Express and IDE auto-configuration utilities, and the video BIOS. The BIOS is stored in the Firmware Hub. The BIOS can be updated by following the instructions on page 53 in Chapter 3. Serial ATA and IDE Auto Configuration If you install a Serial ATA or IDE device (such as a hard drive) in your computer, the auto- configuration utility in the BIOS automatically detects and configures the device for your computer. You do not need to run the BIOS Setup program after installing a Serial ATA or IDE device. You can override the auto-configuration options by specifying manual configuration in the BIOS Setup program. PCI and PCI Express Auto Configuration If you install a PCI/PCI Express add-in card in your computer, the PCI/PCI Express auto- configuration utility in the BIOS automatically detects and configures the resources (IRQs, DMA channels, and I/O space) for that add-in card. You do not need to run the BIOS Setup program after you install a PCI/PCI Express add-in card. Security Passwords The BIOS includes security features that restrict whether the BIOS Setup program can be accessed and who can boot the computer. A supervisor password and a user password can be set for the BIOS Setup and for booting the computer, with the following restrictions: • The supervisor password gives unrestricted access to view and change all Setup options. If only the supervisor password is set, pressing at the password prompt of Setup gives the user restricted access to Setup. • If both the supervisor and user passwords are set, you must enter either the supervisor password or the user password to access Setup. Setup options are then available for viewing and changing depending on whether the supervisor or user password was entered. • Setting a user password restricts who can boot the computer. The password prompt is displayed before the computer is booted. If only the supervisor password is set, the computer boots without asking for a password. If both passwords are set, you can enter either password to boot the computer. Chassis Intrusion The board supports a chassis security feature that detects if the chassis cover has been removed. The security feature uses a mechanical switch on the chassis that can be connected to the chassis intrusion header on the desktop board. See Figure 18 on page 38 for the location of the chassis intrusion header.

19 Power Management Features Power management is implemented at several levels, including: • Advanced Configuration and Power Interface (ACPI) • Hardware support: ⎯ Power connectors ⎯ Fan connectors ⎯ Suspend to RAM (Instantly Available PC technology) ⎯ Resume on Ring ⎯ Wake from USB ⎯ Wake from PS/2 keyboard/mouse ⎯ PME# wakeup support ACPI ACPI gives the operating system direct control over the power management and Plug and Play functions of a computer. The use of ACPI with the desktop board requires an operating system that provides full ACPI support. Power Connectors The desktop board has two power connectors. See Figure 21 on page 42 and Figure 22 on page 43 for the location of the power connectors. Fan Connectors The desktop board has a 4-pin processor fan header and two 3-pin chassis fan headers. See Figure 20 on page 41 for the location of the fan headers. Fan Speed Control (Intel® Precision Cooling Technology) Intel Precision Cooling Technology automatically adjusts the processor fan speed based on the processor thermal diode temperature and adjusts the chassis fan speeds depending on the system temperature. System fan noise may be reduced by operating controlled chassis and processor fans at the minimum necessary speeds. The processor and chassis fan speed control features can be disabled independently through the desktop board BIOS. Disabling the processor fan speed control will result in the fan operating at full speed if it is not a self controlled fan. It is recommended that processor fan speed control remain enabled (default BIOS setting) when using the processor fan heat-sink included with Intel® boxed processors. Disabling the chassis fan speed control results in chassis fans always operating at full speed. The chassis fan speed control feature should be disabled if a self-controlled chassis fan is attached to any controlled chassis fan header. The overall system noise reduction will vary based on system configuration and environment.

20 Suspend to RAM (Instantly Available PC Technology) CAUTION For Instantly Available PC technology, the 5 V standby line for the power supply must be capable of delivering adequate +5 V standby current. Failure to provide adequate standby current when using this feature can damage the power supply and/or effect ACPI S3 sleep state functionality. CAUTION Power supplies used with this desktop board must be able to provide enough standby current to support the standard Instantly Available (ACPI S3 sleep state) configuration. If the standby current necessary to support multiple wake events from the PCI and/or USB buses exceeds power supply capacity, the desktop board may lose register settings stored in memory. Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to-RAM) sleep state. While in the S3 sleep state, the computer will appear to be off. When signaled by a wake-up device or event, the system quickly returns to its last known awake state. The desktop board’s standby power indicator, shown in Figure 2, is lit when there is standby power to the system. This includes the memory modules and PCI bus connectors, even when the computer appears to be off. If the system has a dual-colored power LED on the front panel, the sleep state is indicated by the LED turning amber. OM17367 Figure 2. Location of Standby Power Indicator Related Links: For more information on standby current requirements for the desktop board, refer to the Technical Product Specification by going to the following link, finding the product, and selecting Product Documentation from the left-hand menu: http://support.intel.com/support/motherboards/desktop/

21 Resume on Ring The operation of Resume on Ring can be summarized as follows: • Resumes operation from either ACPI S1 or ACPI S3 state • Requires only one call to access the computer • Detects incoming call similarly for external and internal modems • Requires modem interrupt be unmasked for correct operation Wake from USB NOTE Wake from USB requires the use of a USB peripheral that supports wake from USB. USB bus activity wakes the computer from an ACPI S1 or S3 state. Wake from PS/2 Keyboard/Mouse PS/2 keyboard/mouse activity wakes the computer from an ACPI S1 or S3 state. PME# Wakeup Support When the PME# signal on the PCI bus is asserted, the computer wakes from an ACPI S1, S3, or S5 state. Speaker A speaker is mounted on the desktop board. The speaker provides audible error code (beep code) information during the Power-On Self-Test (POST). Battery A battery on the desktop board keeps the values in CMOS RAM and the clock current when the computer is turned off. Go to page 48 for instructions on how to replace the battery. Real-Time Clock The desktop board has a time-of-day clock and 100-year calendar. The battery on the desktop board keeps the clock current when the computer is turned off.

Board Components This chapter tells you how to: • Install the I/O shield • Install and remove the desktop board • Install and remove a processor and memory • Connect the IDE and Serial ATA cables • Connect internal headers • Set up flexible 6-channel audio with jack re-tasking • Connect fans and power cables • Connect PCI bus add-in cards • Set the BIOS configuration jumper • Clear passwords • Locate back panel connectors • Replace the battery Before You Begin WARNING Warnings indicate conditions that, if not observed, can cause personal injury. The procedures in this chapter assume familiarity with the general terminology associated with personal computers and with the safety practices and regulatory compliance required for using and modifying electronic equipment. Disconnect the computer from its power source and from any telecommunications links, networks, or modems before performing any of the procedures described in this chapter. Failure to disconnect power, telecommunications links, networks, or modems before you open the computer or perform any procedures can result in personal injury or equipment damage. Some circuitry on the board can continue to operate even though the front panel power button is off. Follow these guidelines before you begin: • Always follow the steps in each procedure in the correct order. • Set up a log to record information about your computer, such as model, serial numbers, installed options, and configuration information. • Electrostatic discharge (ESD) can damage components. Perform the procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis.

24 Installation Precautions When you install and test the Intel desktop board, observe all warnings and cautions in the installation instructions. To avoid injury, be careful of: • Sharp pins on connectors • Sharp pins on printed circuit assemblies • Rough edges and sharp corners on the chassis • Hot components (like processors, voltage regulators, and heat sinks) • Damage to wires that could cause a short circuit Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical personnel. Installation Instructions CAUTION Follow these guidelines to meet safety and regulatory requirements when installing this board. Read and adhere to all of these instructions and the instructions supplied with the chassis and associated modules. If the instructions for the chassis are inconsistent with these instructions or the instructions for associated modules, contact the supplier’s technical support to find out how you can ensure that your computer meets safety and regulatory requirements. If you do not follow these instructions and the instructions provided by chassis and module suppliers, you increase safety risk and the possibility of noncompliance with regional laws and regulations. Ensure Electromagnetic Compatibility (EMC) Compliance Before computer integration, make sure that the power supply and other modules or peripherals, as applicable, have passed Class B EMC testing and are marked accordingly. Pay close attention to the following when reading the installation instructions for the host chassis, power supply, and other modules: • Product certifications or lack of certifications • External I/O cable shielding and filtering • Mounting, grounding, and bonding requirements • Keying connectors when mating the wrong connectors could be hazardous If the power supply and other modules or peripherals, as applicable, are not Class B EMC compliant before integration, then EMC testing is required on a representative sample of the newly completed computer.

25 Chassis and Component Certifications Ensure that the chassis and certain components; such as the power supply, peripheral drives, wiring, and cables; are components certified for the country or market where used. Agency certification marks on the product are proof of certification. Typical product certifications include: • In Europe The CE marking signifies compliance with all applicable European requirements. If the chassis and other components are not properly CE marked, a supplier’s Declaration of Conformity statement to the European EMC directive and Low Voltage directive (as applicable), should be obtained. Additionally, other directives, such as the Radio and Telecommunications Terminal Equipment (R&TTE) directive may also apply depending on product features. • In the United States A certification mark by a Nationally Recognized Testing Laboratory (NRTL) such as UL, CSA, or ETL signifies compliance with safety requirements. Wiring and cables must also be UL listed or recognized and suitable for the intended use. The FCC Class B logo for home or office use signifies compliance with electromagnetic interference (EMI) requirements. • In Canada A nationally recognized certification mark such as CSA or cUL signifies compliance with safety requirements. The Industry Canada statement at the front of this product guide demonstrates compliance with Canadian EMC regulations. Industry Canada recognizes and accepts FCC certification as denoting compliance with national electromagnetic interference (emissions) requirements. Prevent Power Supply Overload Do not overload the power supply output. To avoid overloading the power supply, make sure that the calculated total current loads of all the modules within the computer is less than the output current rating of each of the power supplies output circuits. Place Battery Marking CAUTION Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations. There is insufficient space on this Desktop Board to provide instructions for replacing and disposing of the Lithium ion coin cell battery. For system safety certification, the following statement or equivalent statement is required to be permanently and legibly marked on the chassis near the battery. Related Links For information about replacing the battery, go to page 48 in Chapter 2.

26 Use Only for Intended Applications All Intel desktop boards are evaluated as Information Technology Equipment (I.T.E.) for use in personal computers for installation in homes, offices, schools, computer rooms, and similar locations. The suitability of this product for other applications or environments, such as medical, industrial, alarm systems, test equipment, etc. may require further evaluation. Related Links For information about regulatory compliance, go to Appendix B on page 59. Installing the I/O Shield The desktop board comes with an I/O shield. When installed in the chassis, the shield blocks radio frequency transmissions, protects internal components from dust and foreign objects, and promotes correct airflow within the chassis. Install the I/O shield before installing the desktop board in the chassis. Place the shield inside the chassis as shown in Figure 3. Press the shield into place so that it fits tightly and securely. If the shield doesn’t fit, obtain a properly-sized shield from the chassis supplier. OM16533 Figure 3. Installing the I/O Shield

27 Installing and Removing the Desktop Board WARNING Only qualified technical personnel should do this procedure. Disconnect the computer from its power source before performing the procedures described here. Failure to disconnect the power before you open the computer can result in personal injury or equipment damage. NOTE Refer to Appendix B for regulatory requirements. Refer to your chassis manual for instructions on installing and removing the desktop board. Figure 4 shows the location of the mounting holes for the desktop board. OM17368 Figure 4. Mounting Screw Hole Locations

28 Installing and Removing a Processor Instructions on how to install the processor to the desktop board are given below. Installing a Processor CAUTION Before installing or removing the processor, make sure AC power has been removed by unplugging the power cord from the computer; the standby power LED should not be lit (see Figure 2 on page 20). Failure to do so could damage the processor and the board. To install a processor, follow these instructions: 1. Observe the precautions in "Before You Begin" on page 23. 2. Open the socket lever by pushing the lever down and away from the socket (see Figure 5, A and B). OM17210 A B Figure 5. Lift Socket Lever 3. Lift the load plate. Do not touch the socket contacts (see Figure 6, C and D). OM17211 D D C Figure 6. Lift the Load Plate and Don’t Touch the Socket Contacts

29 4. Remove the plastic protective socket cover from the load plate. Do not discard the protective socket cover. Always replace the socket cover if the processor is removed from the socket (see Figure 7, E). OM17228 E Figure 7. Remove the Protective Socket Cover 5. Remove the processor from the protective processor cover. Hold the processor only at the edges, being careful not to touch the bottom of the processor. Do not discard the protective processor cover. Always replace the processor back to the package if the processor is removed from the socket (see Figure 8). OM17213 Figure 8. Remove the Processor from the Protective Processor Cover/Do Not Touch

30 6. Hold the processor with your thumb and index fingers oriented as shown in Figure 9. Make sure fingers align to the socket cutouts (see Figure 9, F). Align notches (see Figure 9, G) with the socket see (Figure 9, H). Lower the processor straight down without tilting or sliding the processor in the socket. OM17214 G G F H F H Figure 9. Install Processor 7. Pressing down on the load plate (Figure 10, I) close and engage the socket lever (Figure 10, J). OM17215 I J Figure 10. Close the Load Plate

31 Installing the Processor Fan Heat Sink The desktop board has an integrated processor fan heat sink retention mechanism (RM). For instructions on how to attach the processor fan heat sink to the integrated processor fan heat sink RM, refer to the boxed processor manual or the Intel World Wide Web site at: http://support.intel.com/support/processors/pentium4/intnotes478.htm Connecting the Processor Fan Heat Sink Cable Connect the processor fan heat sink cable to the 4-pin processor fan connector (see Figure 11). NOTE If a 3-pin fan connector is used in a 4-pin fan header, the fan will not be controlled and will run at full speed. OM17369 3 1 2 4 3 1 2 4 A B 3 1 2 3 1 2 B A Figure 11. Connecting the Processor Fan Heat Sink Cable to the Processor Fan Connector

32 Removing the Processor For instruction on how to remove the processor fan heat sink and processor, refer to the processor installation manual or the Intel World Wide Web site at: http://support.intel.com/support/processors/pentium4/inuse.htm Installing and Removing Memory NOTE To be fully compliant with all applicable Intel SDRAM memory specifications, the boards require DIMMs that support the Serial Presence Detect (SPD) data structure. You can access the PC Serial Presence Detect Specification at: http://www.intel.com/technology/memory/pcsdram/spec/ The desktop board has four 184-pin DDR DIMM sockets arranged as DIMM 0 (blue) and DIMM 1 (black) in both Channel A and Channel B. Guidelines for Dual Channel Memory Configuration Before installing DIMMs, read and follow these guidelines for dual channel configuration. Two or Four DIMMs Install a matched pair of DIMMs equal in speed and size in DIMM 0 (blue) of both channels A and B (see Figure 12). Channel A 1 GB, 400 MHz DIMM 0 DIMM 1 Channel B 1 GB, 400 MHz DIMM 0 DIMM 1 Figure 12. Dual Configuration Example 1

33 If additional memory is to be used, install another matched pair of DIMMs in DIMM 1 (black) in both channels A and B (see Figure 13). Channel A 256 MB, 400 MHz DIMM 0 512 MB, 400 MHz DIMM 1 Channel B 256 MB, 400 MHz DIMM 0 512 MB, 400 MHz DIMM 1 Figure 13. Dual Configuration Example 2 Three DIMMs Install a matched pair of DIMMs equal in speed and size in DIMM 0 (blue) and DIMM 1 (black) of channel A. Install a DIMM equal in speed and total size of the DIMMs installed in channel A in either DIMM 0 or DIMM 1 of channel B (see Figure 14). Channel A 256 MB, 400 MHz DIMM 0 256 MB, 400 MHz DIMM 1 Channel B 512 MB, 400 MHz DIMM 0 DIMM 1 Figure 14. Dual Configuration Example 3 NOTE All other memory configurations will result in single channel memory operation.

34 Installing DIMMs 1. Observe the precautions in "Before You Begin" on page 23. 2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord. 3. Remove the computer’s cover and locate the DIMM sockets (see Figure 15). OM17370 Channel A Channel B DIMM 1 DIMM 0 DIMM 1 DIMM 0 Figure 15. Installing a DIMM

35 4. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position. 5. Holding the DIMM by the edges, remove it from its anti-static package. 6. Position the DIMM above the socket. Align the small notch at the bottom edge of the DIMM with the keys in the socket (see inset in Figure 15). 7. Insert the bottom edge of the DIMM into the socket. 8. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips snap into place. Make sure the clips are firmly in place. 9. Replace the computer’s cover and reconnect the AC power cord. Removing DIMMs To remove a DIMM, follow these steps: 1. Observe the precautions in "Before You Begin" on page 23. 2. Turn off all peripheral devices connected to the computer. Turn off the computer. 3. Remove the AC power cord from the computer. 4. Remove the computer’s cover. 5. Gently spread the retaining clips at each end of the DIMM socket. The DIMM pops out of the socket. 6. Hold the DIMM by the edges, lift it away from the socket, and store it in an anti-static package. 7. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM sockets. 8. Replace the computer’s cover and reconnect the AC power cord.

36 Connecting the IDE Cable The IDE cable can connect two drives to the desktop board. The cable supports the ATA-66/100 transfer protocol. Figure 16 shows the correct installation of the cable. NOTE ATA-66/100 compatible cables are backward compatible with drives using slower IDE transfer protocols. If an ATA-66/100 disk drive and a disk drive using any other IDE transfer protocol are attached to the same cable, the maximum transfer rate between the drives may be reduced to that of the slowest drive. NOTE Do not connect an ATA device as a slave on the same IDE cable as an ATAPI master device. For example, do not connect an ATA hard drive as a slave to an ATAPI CD-ROM drive. For correct function of the cable: • Observe the precautions in "Before You Begin" on page 23. • Attach the cable end with the single connector to the Intel desktop board (Figure 16, A). • Attach the cable end with the two closely spaced connectors to the drives (Figure 16, B). OM17371 A B Figure 16. Connecting the IDE Cable

37 Connecting the Serial ATA (SATA) Cable The SATA cable (4-conductor) supports the Serial ATA protocol and connects a single drive to the desktop board. Either end of the cable can be connected to the SATA drive or the connector on the board. For correct cable function: 1. Observe the precaution in "Before You Begin" on page 23. 2. Attach either cable end to the connector (Figure 17, A) on the board. 3. Attach the other cable end to the drive (Figure 17, B). OM17372 A B Figure 17. Connecting the Serial ATA Cable

38 Connecting Internal Headers Before connecting cables to the internal headers, observe the precautions in "Before You Begin" on page 23. Figure 18 shows the location of the internal headers. OM17259 D B C 1 5 6 7 3 4 2 10 9 Port1L Port1R Port2R Sense_Send Port2L GND Presence# Sense1_Ret Key (no pin) Sense2_Ret 1 3 On/Off Power LED HD LED Reset No Connection 1 2 3 4 5 7 6 8 9 USB A USB B 1 5 6 7 8 3 4 2 10 Power (+5V) Power (+5V) D- D+ Ground Key (no pin) N/C D- D+ Ground E A 1 Item Description A Chassis intrusion B Power LED C Front panel D USB 2.0 E Front panel audio Figure 18. Internal Headers

39 Connecting the USB 2.0 Headers Before connecting the USB 2.0 headers, observe the precautions in "Before You Begin" on page 23. See Figure 18, D on page 38 for the location of the black USB 2.0 headers. Table 5 shows the pin assignments for the USB 2.0 headers. Table 5. USB 2.0 Header Signal Names USB Port A USB Port B Pin Signal name Pin Signal name 1 Power 2 Power 3 D- 4 D- 5 D+ 6 D+ 7 Ground 8 Ground 9 Key 10 No connect Note: USB ports may be assigned as needed. Connecting the Front Panel Header Before connecting the front panel header, observe the precautions in "Before You Begin" on page 23. See Figure 18, C on page 38 for the location of the multi-colored front panel header. Table 6 shows the pin assignments for the front panel header. Table 6. Front Panel Header Signal Names Pin Signal In/Out Description Pin Signal In/Out Description Hard Drive Activity LED (Orange) Power LED (Green) 1 HD_PWR Out Hard disk LED pull-up (330 Ω) to +5 V 2 HDR_BLNK_GRN Out Front panel green LED 3 HDA# Out Hard disk active LED 4 HDR_BLNK_YEL Out Front panel yellow LED Reset Switch (Purple) On/Off Switch (Red) 5 Ground Ground 6 SWITCH_ON# In Power switch 7 FP_RESET# In Reset switch 8 Ground Ground 9 N/C Not connected 10 No pin No pin Connecting the Front Panel Audio Header Figure 18, E on page 38 shows the location of the yellow front panel audio header. Table 7 shows the pin assignments for the front panel audio header. Table 7. Front Panel Audio Header Signal Names Pin Signal Name Pin Signal Name 1 Port1L 2 GND 3 Port1R 4 Presence# 5 Port2R 6 Sense1 Ret 7 Sense Send 8 Key (no pin) 9 Port2L 10 Sense2 Ret

40 Connecting to the Flexible 6-Channel Audio System Installing the audio driver from the Intel Express Installer CD-ROM enables the flexible, analog audio system. The back panel audio connectors support up to six speakers and are retaskable using the audio driver interface. Typical connector assignments are shown in the table in Figure 19. OM15694 A B C Item Description A Line In [retaskable as Rear Left/Right Out] B Line Out [Front Left/Right Out] C Mic In [retaskable as Center/LFE (Subwoofer) Out] Figure 19. Back Panel Audio Connectors for Flexible 6-Channel Audio System Connect speakers as follows: • If using two speakers, connect the pair to connector (B). • If using four speakers, do the following: ⎯ Connect the front left/right speakers to connector (B). ⎯ Connect the rear left/right speakers to connector (A). ⎯ Using the audio driver interface, retask connector (A) to be Rear Left/Right Out. • If using six speakers, do the following: ⎯ Connect the front left/right speakers to connector (B). ⎯ Connect the rear left/right speakers to connector (A). ⎯ Connect the center/subwoofer speakers to connector (C). ⎯ Using the audio driver interface, retask connector (A) to be Rear Left/Right Out and retask connector (C) to be Center/LFE Out.

41 Connecting Fan and Power Cables Connecting Fan Cables Figure 20 shows the location of the fan headers. Connect the processor’s fan heat sink cable to the 4-pin processor fan header on the board. Connect chassis fan cables to the 3-pin fan headers. NOTE If a 3-pin fan connector is used in a 4-pin fan header, the fan will not be controlled and will run at full speed. OM17373 3 1 2 4 3 1 2 4 A B 3 1 2 3 1 2 B A Figure 20. Location of Fan Headers

42 Connecting Power Cables CAUTION Failure to use an ATX12V power supply, or not connecting the 12 V (2x2) processor core voltage power supply connector to the desktop board may result in damage to the desktop board and/or power supply. Connecting 2x10 Power Supply Cables The 2x12 main power connector on the desktop board is backwards compatible with ATX12V power supplies with 2x10 power connections. Figure 21 shows the location of the power connectors. OM17260 2X10 1 2 Figure 21. Connecting 2x10 Power Supply Cables 1. Observe the precautions in "Before You Begin" on page 23. 2. Connect the 12 V processor core voltage power supply cable to the 2x2 connector. 3. Connect the main power supply cable to the 2x10 connector.

43 Connecting 2x12 Power Supply Cables If you have a 2x12 power supply, follow the instruction below. Figure 22 shows the location of the power connectors. OM17361 2X12 1 2 Figure 22. Connecting 2x12 Power Supply Cables 1. Observe the precautions in "Before You Begin" on page 23. 2. Connect the 12 V processor core voltage power supply cable to the 2x2 connector. 3. Connect the main power supply cable to the 2x12 connector.

44 Other Connectors Figure 23 shows the location of the PCI bus add-in card connectors, PCI Express x1 add-in card connector, and peripheral interface connectors for the desktop board. OM17374 D E A B C F Item Description A PCI Express x1 connectors B PCI bus add-in card connector 2 (SMBUS routed) C PCI bus add-in card connector 1 D Diskette drive connector E IDE connector F Serial ATA connectors Figure 23. Location of Other Connectors

45 Setting the BIOS Configuration Jumper Block CAUTION Always turn off the power and unplug the power cord from the computer before changing the jumper. Moving the jumper with the power on may result in unreliable computer operation. Figure 24 shows the location of the desktop board’s BIOS configuration jumper. OM17375 1 3 Figure 24. Location of the BIOS Configuration Jumper Block The three-pin BIOS jumper block enables all board configurations to be done in BIOS Setup. Table 8 shows the jumper settings for the Setup program modes. Table 8. Jumper Settings for the BIOS Setup Program Modes Jumper Setting Mode Description 3 1 Normal (default) (1-2) The BIOS uses the current configuration and passwords for booting. 3 1 Configure (2-3) After the Power-On Self-Test (POST) runs, the BIOS displays the Maintenance Menu. Use this menu to clear passwords. 3 1 Recovery (None) The BIOS recovers data from a recovery diskette in the event of a failed BIOS update.

46 Clearing Passwords This procedure assumes that the board is installed in the computer and the configuration jumper block is set to normal mode. 1. Observe the precautions in "Before You Begin" on page 23. 2. Turn off all peripheral devices connected to the computer. Turn off the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4. Find the configuration jumper block (see Figure 24). 5. Place the jumper on pins 2-3 as shown below. 3 1 6. Replace the cover, plug in the computer, turn on the computer, and allow it to boot. 7. The computer starts the Setup program. Setup displays the Maintenance menu. 8. Use the arrow keys to select Clear Passwords. Press and Setup displays a pop-up screen requesting that you confirm clearing the password. Select Yes and press . Setup displays the maintenance menu again. 9. Press to save the current values and exit Setup. 10. Turn off the computer. Disconnect the computer’s power cord from the AC power source. 11. Remove the computer cover. 12. To restore normal operation, place the jumper on pins 1-2 as shown below. 3 1 13. Replace the cover, plug in the computer, and turn on the computer.

47 Back Panel Connectors NOTE The line out connector, located on the back panel, is designed to power either headphones or amplified speakers only. Poor audio quality may occur if passive (non-amplified) speakers are connected to this output. Figure 25 shows the location of the back panel connectors. OM17265 Line In RJ45 Figure 25. Back Panel Connectors

48 Replacing the Battery A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at 25 ºC with 3.3 VSB applied. When the voltage drops below a certain level, the BIOS Setup program settings stored in CMOS RAM (for example, the date and time) might not be accurate. Replace the battery with an equivalent one. Figure 26 on page 52 shows the location of the battery. CAUTION Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations. PRECAUTION Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les piles usagées doivent être recyclées dans la mesure du possible. La mise au rebut des piles usagées doit respecter les réglementations locales en vigueur en matière de protection de l'environnement. FORHOLDSREGEL Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier bør om muligt genbruges. Bortskaffelse af brugte batterier bør foregå i overensstemmelse med gældende miljølovgivning. OBS! Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier bør kastes i henhold til gjeldende miljølovgivning. VIKTIGT! Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras enligt de lokala miljövårdsbestämmelserna. VARO Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on mahdollista. Käytetyt paristot on hävitettävä paikallisten ympäristömääräysten mukaisesti. VORSICHT Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend.

49 AVVERTIMENTO Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del produttore. PRECAUCIÓN Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del fabricante. WAARSCHUWING Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij. Batterijen moeten zoveel mogelijk worden gerecycled. Houd u bij het weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving. ATENÇÃO Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto. As baterias devem ser recicladas nos locais apropriados. A eliminação de baterias usadas deve ser feita de acordo com as regulamentações ambientais da região. AŚCIAROŽZNAŚĆ Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу. Акумулятары павінны, па магчымасці, перепрацоўвацца. Пазбаўляцца ад старых акумулятараў патрэбна згодна з мясцовым заканадаўствам па экалогіі. UPOZORNÌNÍ V případě výměny baterie za nesprávný druh může dojít k výbuchu. Je-li to možné, baterie by měly být recyklovány. Baterie je třeba zlikvidovat v souladu s místními předpisy o životním prostředí. Προσοχή Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η µπαταρία αντικατασταθεί από µία λανθασµένου τύπου. Οι µπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι δυνατό. Η απόρριψη των χρησιµοποιηµένων µπαταριών πρέπει να γίνεται σύµφωνα µε τους κατά τόπο περιβαλλοντικούς κανονισµούς. VIGYÁZAT Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket lehetőség szerint újra kell hasznosítani. A használt telepeket a helyi környezetvédelmi előírásoknak megfelelően kell kiselejtezni.

50 AWAS Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan. OSTRZEŻENIE Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu baterii. Zużyte baterie należy w miarę możliwości utylizować zgodnie z odpowiednimi przepisami ochrony środowiska. PRECAUŢIE Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător. Bateriile trebuie reciclate, dacă este posibil. Depozitarea bateriilor uzate trebuie să respecte reglementările locale privind protecţia mediului. ВНИМАНИЕ При использовании батареи несоответствующего типа существует риск ее взрыва. Батареи должны быть утилизированы по возможности. Утилизация батарей должна проводится по правилам, соответствующим местным требованиям. UPOZORNENIE Ak batériu vymeníte za nesprávny typ, hrozí nebezpečenstvo jej výbuchu. Batérie by sa mali podľa možnosti vždy recyklovať. Likvidácia použitých batérií sa musí vykonávať v súlade s miestnymi predpismi na ochranu životného prostredia. POZOR Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo. Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi. การระวัง ระวังการระเบิดที่เกิดจากเปลี่ยนแบตเตอรี่ผิดประเภท หากเปนไปได ควรนําแบตเตอรี่ไปรีไซเคิล การทิ้งแบตเตอรี่ใชแลวตองเปนไปตามกฎขอบังคับดานสิ่งแวดลอมของทองถิ่น. UYARI Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri dönüştürülmelidir. Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır.

51 OСТОРОГА Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху. Якщо можливо, використані батареї слід утилізувати. Утилізація використаних батарей має бути виконана згідно місцевих норм, що регулюють охорону довкілля. ETTEVAATUST ATTENZJONI

52 To replace the battery, follow these steps: 1. Observe the precautions in "Before You Begin" (see page 23). 2. Turn off all peripheral devices connected to the computer. Disconnect the computer’s power cord from the AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4. Locate the battery on the board (see Figure 26). 5. With a medium flat-bladed screwdriver, gently pry the battery free from its connector. Note the orientation of the “+” and “-” on the battery. 6. Install the new battery in the connector, orienting the “+” and “-” correctly. 7. Replace the computer cover. OM17376 Figure 26. Removing the Battery

BIOS Setup program is accessed by pressing the key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. OM17050 F2 Figure 27. F2 Key This chapter tells you how to update the BIOS by either using the Intel Express BIOS Update utility or the Iflash Memory Update utility, and how to recover the BIOS if an update fails. Updating the BIOS with the Intel® Express BIOS Update Utility With the Intel Express BIOS Update utility you can update the system BIOS while in the Windows environment. The BIOS file is included in an automated update utility that combines the functionality of the Intel® Flash Memory Update Utility and the ease-of use of Windows-based installation wizards. To update the BIOS with the Intel Express BIOS Update utility: 1. Go to the Intel World Wide Web site: http://support.intel.com/support/motherboards/desktop/ 2. Navigate to the D915GVWB page, click “[view] Latest BIOS updates,” and select the Express BIOS Update utility file. 3. Download the file to your hard drive. (You can also save this file to a diskette. This is useful if you are updating the BIOS for multiple identical systems.) 4. Close all other applications. This step is required. Your system will be rebooted at the last Express BIOS Update window. 5. Double-click the executable file from the location on your hard drive where it was saved. This runs the update program. 6. Follow the instructions provided in the dialog boxes to complete the BIOS update.

54 Updating the BIOS with the Iflash Memory Update Utility With the Iflash BIOS update utility you can update the system BIOS from a floppy disk or other bootable media. The utility available from the Web provides a simple method for creating a bootable flash memory update floppy that will automatically update your BIOS. Obtaining the BIOS Update File You can update to a new version of the BIOS by using the BIOS update file. The BIOS update file is a compressed self-extracting archive that contains all the files you need to update the BIOS. The BIOS update file contains: • New BIOS files • BIOS recovery files • Intel Flash Memory Update Utility You can obtain the BIOS update file through your computer supplier or by navigating to the Desktop Board D915GVWB page on the Intel World Wide Web site at: http://support.intel.com/support/motherboards/desktop Navigate to the D915GVWB page, click “[view] Latest BIOS updates,” and select the Iflash BIOS Update utility file. NOTE Review the instructions distributed with the update utility before attempting a BIOS update. The Iflash Memory Update utility allows you to: • Update the BIOS in flash memory • Update the language section of the BIOS Updating the BIOS CAUTION The AUTOEXEC.BAT file provided with the update files updates the BIOS. Do not interrupt the process or the system may not function. 1. Boot the computer with the BIOS update diskette in drive A. During system boot, the AUTOEXEC.BAT file provided with the update files will automatically run the BIOS update process. 2. When the update process is complete, the monitor will display a message telling you to remove the diskette and to reboot the system. 3. As the computer boots, check the BIOS identifier (version number) to make sure the update was successful. If a logo appears, press to view the POST messages.

It is unlikely that anything will interrupt the BIOS update; however, if an interruption occurs, the BIOS could be damaged. The following steps explain how to recover the BIOS if an update fails. The following procedure uses recovery mode for the Setup program. See page 45 for more information on Setup modes. NOTE Because of the small amount of code available in the boot block area, there is no video support. You will not see anything on the screen during this procedure. Monitor the procedure by listening to the speaker and looking at the diskette drive LED. 1. Turn off the computer, disconnect the computer’s power cord, and disconnect all external peripherals. 2. Remove the computer cover and locate the configuration jumper block (see Figure 24). 3. Remove the jumper from all pins as shown below to set recovery mode for Setup. 3 1 4. Insert the bootable BIOS update diskette into diskette drive A. 5. Replace the computer cover, connect the power cord, turn on the computer, and allow it to boot. The recovery process will take a few minutes. 6. Listen to the speaker: • Upon applying power, drive A will begin to show activity. In about a minute, two beeps are heard and drive A activity ceases (temporarily) indicating the successful recovery of the BIOS core. Drive A activity will begin again followed by two more beeps indicating the successful recovery of the boot block. This sequence of events indicates a successful BIOS recovery. • A series of continuous beeps indicates a failed BIOS recovery. 7. If recovery fails, return to step 1 and repeat the recovery process. 8. If recovery is successful, turn off the computer, and disconnect its power cord. 9. Remove the computer cover and continue with the following steps. 10. On the jumper block, reinstall the jumper back on pins 1-2 as shown below to set normal mode for Setup. 3 1 11. Leave the update diskette in drive A, replace the computer cover, and connect the computer’s power cord. 12. Turn on the computer and continue with the BIOS update.

Desktop Board D915GVWB reports POST errors in two ways: • By sounding a beep code • By displaying an error message on the monitor BIOS Beep Code The BIOS issues a beep code during POST if a memory error occurred. If a repeating beep code is heard and the desktop board does not boot, see Table 9 for beep code descriptions. Table 9. BIOS Beep Code Number of Beeps Description 1 Refresh failure 2 Parity cannot be reset 3 First 64 K memory failure 4 Timer not operational 5 Processor failure (Reserved; not used) 6 8042 GateA20 cannot be toggled (memory failure or not present) 7 Exception interrupt error 8 Display memory R/W error 9 (Reserved; not used) 10 CMOS Shutdown register test error 11 Invalid BIOS (such as, POST module not found) BIOS Error Messages When a recoverable error occurs during the POST, the BIOS displays an error message describing the problem. Table 10 gives an explanation of the BIOS error messages. Table 10. BIOS Error Messages Error Message Explanation GA20 Error An error occurred with Gate-A20 when switching to protected mode during the memory test. Pri Master HDD Error Pri Slave HDD Error Sec Master HDD Error Sec Slave HDD Error Could not read sector from corresponding drive. Pri Master Drive - ATAPI Incompatible Pri Slave Drive - ATAPI Incompatible Sec Master Drive - ATAPI Incompatible Sec Slave Drive - ATAPI Incompatible Corresponding drive is not an ATAPI device. Run Setup to make sure device is selected correctly. continued

58 Table 10. BIOS Error Messages (continued) Error Message Explanation A: Drive Error B: Drive Error No response from the diskette drive. CMOS Battery Low The battery may be losing power. Replace the battery soon. CMOS Display Type Wrong The display type is different than what has been stored in CMOS. Check Setup to make sure type is correct. CMOS Checksum Bad The CMOS checksum is incorrect. CMOS memory may have been corrupted. Run Setup to reset values. CMOS Settings Wrong CMOS values are not the same as the last boot. These values have either been corrupted or the battery has failed. CMOS Date/Time Not Set The time and/or date values stored in CMOS are invalid. Run Setup to set correct values. DMA Error Error during read/write test of DMA controller. FDC Failure Error occurred trying to access diskette drive controller. HDC Failure Error occurred trying to access hard disk controller. Checking NVRAM..... NVRAM is being checked to see if it is valid. Update OK! NVRAM was invalid and has been updated. Updated Failed NVRAM was invalid but was unable to be updated. Keyboard Is Locked The system keyboard lock is engaged. The system must be unlocked to continue to boot. Keyboard Error Error in the keyboard connection. Make sure keyboard is connected properly. KB/Interface Error Keyboard interface test failed. Memory Size Decreased Memory size has decreased since the last boot. If no memory was removed, then memory may be bad. Memory Size Increased Memory size has increased since the last boot. If no memory was added, there may be a problem with the system. Memory Size Changed Memory size has changed since the last boot. If no memory was added or removed, then memory may be bad. No Boot Device Available System did not find a device to boot. Off Board Parity Error A parity error occurred on an offboard card. This error is followed by an address. On Board Parity Error A parity error occurred in onboard memory. This error is followed by an address. Parity Error A parity error occurred in onboard memory at an unknown address. NVRAM / CMOS / PASSWORD cleared by Jumper NVRAM, CMOS, and passwords have been cleared. The system should be powered down and the jumper removed. Pressed CMOS is ignored and NVRAM is cleared. User must enter Setup.

This appendix contains the following regulatory compliance information for the Desktop Board D915GVWB: • Safety regulations • European Union Declaration of Conformity statement • Product Ecology statements • Electromagnetic Compatibility (EMC) regulations • Product certification markings Safety Regulations The Desktop Board D915GVWB complies with the safety regulations stated in Table 11 when correctly installed in a compatible host system. Table 11. Safety Regulations Regulation Title UL 60950-1:2003/ CSA C22.2 No. 60950-1-03 Information Technology Equipment – Safety - Part 1: General Requirements (USA and Canada) EN 60950-1:2002 Information Technology Equipment – Safety - Part 1: General Requirements (European Union) IEC 60950-1:2001, First Edition Information Technology Equipment – Safety - Part 1: General Requirements (International) European Union Declaration of Conformity Statement We, Intel Corporation, declare under our sole responsibility that the product Intel® Desktop Board D915GVWB is in conformity with all applicable essential requirements necessary for CE marking, following the provisions of the European Council Directive 89/336/EEC (EMC Directive) and Council Directive 73/23/EEC (Safety/Low Voltage Directive). The product is properly CE marked demonstrating this conformity and is for distribution within all member states of the EU with no restrictions. This product follows the provisions of the European Directives 89/336/EEC and 73/23/EEC.

60 Čeština Tento výrobek odpovídá požadavkům evropských směrnic 89/336/EEC a 73/23/EEC. Dansk Dette produkt er i overensstemmelse med det europæiske direktiv 89/336/EEC & 73/23/EEC. Dutch Dit product is in navolging van de bepalingen van Europees Directief 89/336/EEC & 73/23/EEC. Eesti Antud toode vastab Euroopa direktiivides 89/336/EEC ja 73/23/EEC kehtestatud nõuetele. Suomi Tämä tuote noudattaa EU-direktiivin 89/336/EEC & 73/23/EEC määräyksiä. Français Ce produit est conforme aux exigences de la Directive Européenne 89/336/EEC & 73/23/EEC. Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie 89/336/EEC & 73/23/EEC. Ελληνικά Το παρόν προϊόν ακολουθεί τις διατάξεις των Ευρωπαϊκών Οδηγιών 89/336/ΕΟΚ και 73/23/ΕΟΚ. Magyar E termék megfelel a 89/336/EEC és 73/23/EEC Európai Irányelv előírásainak. Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 89/336/ EEC & 73/23/EEC. Italiano Questo prodotto è conforme alla Direttiva Europea 89/336/EEC & 73/23/EEC. Latviešu Šis produkts atbilst Eiropas Direktīvu 89/336/EEC un 73/23/EEC noteikumiem. Lietuvių Šis produktas atitinka Europos direktyvų 89/336/EEC ir 73/23/EEC nuostatas. Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej 89/336/EEC u 73/23/EEC. Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 89/336/ EEC & 73/23/EEC. Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej 89/336/EWG i 73/23/EWG. Portuguese Este produto cumpre com as normas da Diretiva Européia 89/336/EEC & 73/23/EEC. Español Este producto cumple con las normas del Directivo Europeo 89/336/EEC & 73/23/EEC. Slovensky..Tento produkt je v súlade s ustanoveniami európskych direktív 89/336/EEC a 73/23/EEC. Slovenščina Izdelek je skladen z določbami evropskih direktiv 89/336/EGS in 73/23/EGS. Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 89/336/EEC & 73/23/EEC. Türkçe Bu ürün, Avrupa Birliği’nin 89/336/EEC ve 73/23/EEC yönergelerine uyar.

The following information is provided to address worldwide product ecology concerns and regulations. Disposal Considerations This product contains the following materials that may be regulated upon disposal: lead solder on the printed wiring board assembly. Recycling Considerations Intel encourages its customers to recycle its products and their components (e.g., batteries, circuit boards, plastic enclosures, etc.) whenever possible. In the U.S., a list of recyclers in your area can be found at: http://www.eiae.org In the absence of a viable recycling option, products and their components must be disposed of in accordance with all applicable local environmental regulations. EMC Regulations Desktop Board D915GVWB complies with the EMC regulations stated in Table 12 when correctly installed in a compatible host system. Table 12. EMC Regulations Regulation Title FCC Class B Title 47 of the Code of Federal Regulations, Parts 2 and 15, Subpart B, Radio Frequency Devices. (USA) ICES-003 (Class B) Interference-Causing Equipment Standard, Digital Apparatus. (Canada) EN55022: 1998 (Class B) Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment. (European Union) EN55024: 1998 Information Technology Equipment – Immunity Characteristics Limits and methods of measurement. (European Union) AS/NZS 3548 (Class B) Australian Communications Authority, Standard for Electromagnetic Compatibility. (Australia and New Zealand) CISPR 22, 3rd Edition, (Class B) Limits and methods of measurement of Radio Disturbance Characteristics of Information Technology Equipment. (International) CISPR 24: 1997 Information Technology Equipment – Immunity Characteristics – Limits and Methods of Measurement. (International) VCCI (Class B) Voluntary Control for Interference by Information Technology Equipment (Japan)

62 Japanese Kanji statement translation: this is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Korean Class B statement translation: this is household equipment that is certified to comply with EMC requirements. You may use this equipment in residential environments and other non- residential environments.

Desktop Board D915GVWB has the product certification markings shown in Table 13: Table 13. Product Certification Markings Description Mark UL joint US/Canada Recognized Component mark. Includes adjacent UL file number for Intel desktop boards: E210882 (component side). FCC Declaration of Conformity logo mark for Class B equipment; includes Intel name and D915GVWB model designation (component side). CE mark. Declares compliance to European Union (EU) EMC directive (89/336/EEC) and Low Voltage directive (73/23/EEC) (component side). The CE mark should also be on the shipping container. Australian Communications Authority (ACA) C-tick mark. Includes adjacent Intel supplier code number, N-232. The C-tick mark should also be on the shipping container. Japan VCCI (Voluntary Control Council for Interference) mark. S. Korea MIC (Ministry of Information and Communication) mark. Printed wiring board manufacturer’s recognition mark: consists of a unique UL recognized manufacturer’s logo, along with a flammability rating (solder side). V-0 or 94V-0