Sampo SME-27HD5 Operation & User’s Manual

WIDE SCREEN 34” (32” Viewable) 4:3 SUPER FLAT TUBE 29” (27” Viewable) 4:3 SUPER FLAT TUBE HIGH DEFINITION DIGITAL TELEVISION USER MANUAL

1.FCC STATEMENT.……………………………………………............………………… 1 2.IMPORTANT SAFETY INSTRUCTION……………………………………………… 2-5 3.BACK PANEL AND CONNECTION…………..……………………………........……6-7 4.LOCATION OF BUTTONS ON REMOTE CONTROL.…………………………..……8 5.USING THE TV’ S ADVANCED FEATURES........................................................9-15 6.USING THE MONITOR’ S ADVANCED FEATURES.……………………….....…16-17 7.BATTERY IN REMOTE CONTROL…………..………….…………….......................18 8.FRONT PANEL AND CONNECTIONS……………………………….....………....19-21 9.ON SCREEN DISPLAY MENU SETTINGS………………………….................…22-28 10. TROUBLE SHOOTING…………….………………………….……………….…… 29-30 11.FREQUENCY TABLE……………………………………………………………..… 31-33 12.SPECIFICATIONS…………………………………………………………………… 34-3

-1- IMPORTANT: The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in strict accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measure: l Reorient or relocate the receiving antenna. l Increase the separation between the equipment and the receiver. l Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. l Consult the dealer or an experienced radio/TV technician for help. Shielded interconnected cables and shield power cords must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the manufacturer could void the user’ s authority to operate the equipment and invalidate the warranty. CANADIAN COMPLIANCE STATEMENT: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

-2- 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Umeine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Verletzungen hervorrufen. Verwenden Sie nur sichere Standorte und beachten Sie die Aufstellhinweise des Herstellers. 7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor Überhitzung schützt. Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden. 8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte. 9. Die Netzanschlußsteckdose muß aus Gründen der elektrischen Sicherheit einen Schutzleiterkontakt haben. 10. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden. 11. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten. 12. Wird das Gerät uber einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen.Somit wird im Falle einer Überspannung eine Beschädigung vermieden. 13. Durch die Lüftungsäffnungen dürfen niemals Gegenstände oder Flussigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen. 14. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden. 15. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu überprufen: l Netzkabel oder Netzstecker sind beschädigt. l Flussigkeit ist in das Gerät eingedrungen. l Das Gerät war Feuchtigkeit ausgesetzt. l Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. l Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt. l Wenn das Gerät deutliche Anzeichen eines Defektes aufweist. 16. Bei Reparaturen dürfen nur Orginalersatzteile bzw. Den Orginalteilen entsprechende Teile verwendet werden. Der Einsatz von ungeeigneten Ersatzteilen kann eine weitere Beschädigung hervorrufen. 17. Wenden Sie sich mit allen Fragen die Service und Reparatur betreffen an Ihren Servicepartner. Somit stellen Sie die Betriebssicherheit des Gerätes sicher.

-3- WARNING: 1. To prevent fire or shock hazard, do not expose this monitor to rain to rain or moisture. 2. High voltage exists on the cathode-ray tube anode lead of this monitor. Before servicing, determine the presence of high voltage by connecting the H.V. meter between the anode of CRT cap and chassis only. PRECAUTIONS: 1. Keep monitor away from excessive dust, high temperatures, moisture or direct sunlight. 2. Use in a well-ventilated area and do not cover ventilation openings. 3. Unauthorized modification to this equipment or usage of an unshielded connecting cable may cause excessive interference. 4. If the picture displayed is in any way abnormal, turn off the unit and disconnect it from the electric outlet. Verify your signal wire connections and reconnect the TV to the electric outlet. 5. Read all of these instructions and Save these instructions for later use. 6. Follow all warnings and instructions marked on the product. 7. Disconnect from the mains supply before cleaning. Do not use liquid or aerosol cleaners. Use only a slightly damp cloth for cleaning. 8. Do not use this product near water. 9. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage. 10. The ventilation slots located on the back of the cabinet are for proper heat dissipation. To ensure reliable operation of the unit and to protect it from overheating, do not block or cover the openings. Do not place the unit on a bed, sofa, rug, or other similar surfaces. Never place the unit near or over a radiator or heat source. Do not install unit in an enclosed area unless proper ventilation is provided. 11. The unit should be operated from the type of power source indicated on the label. If the type of available power is unknown, consult your dealer or local power company. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE TV/MONITOR’ S COVER. NO USER SERVICEABLE PARTS ARE INSIDE THE UNIT. PLEASE REFER SERVICING TO QUALIFIED PERSONNEL.

-4- 12. The unit is equipped with a 3-pin grounded plug. The plug will only fit into a grounded power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician. Do not alter the plug; this will defeat the safety feature. 13. Do not rest objects on the power cord. 14. Avoid placing the power cord near high traffic areas. 15. If an extension cord is used, make sure that the total ampere ratings of the products connected to the extension cord do not exceed the extension cord ampere rating. Also make sure that the total amperes of all products connected to the main outlet does not exceed 15 amperes. 16. Never push objects of any kind into the unit through its ventilation slots. This may result in dangerous voltage points or electrical shorting of parts, resulting in fire or electric shock. Never spill liquid of any kind on the unit. 17. Do not attempt to service unit yourself. Opening or removing the cover may result in exposure to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. 18. Disconnect the unit from the main supply and refer servicing to qualified service personnel under the following conditions: l Power cord or plug is damaged or frayed. l Liquid has been spilled into the product. l Unit has been exposed to water or moisture. l Uit does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions, improper adjustment of other controls may result in damage which often requires extensive work by a qualified technician to restore the unit to normal operation. l Unit has been dropped or the cabinet has been damaged. l Unit exhibits a distinct change in performance, indicating a need for service.

-5-  AC IN: This terminal is for AC power cord. ­ RGB IN: This terminal is for RGB analog signal, use with IBM PC and other compatibles. ® RGB OUT: Terminal for RGB signal output so that you can attach another display monitor to display the same RGB analog signal that your monitor is currently displaying. ¯ RGB AUDIO IN: These terminals are for sound signal when monitor is in RGB mode. ° AV IN: Terminals are for video and stereo sound signals, used with video equipment with composite video outputs. ± S-VIDEO 3: Terminals are for S-VIDEO and stereo sound signals, used with video equipment with Composite video outputs. Æ AV OUT: Terminals can output composite video and sound signals that the monitor is using. AV OUT only supplies composite video signals. Y/PB/PR and Y/CB/CR signals are not supported. ³ Y/PB/PR: Terminal is for progressive-scan component input (Y PB PR) video signals and stereo sound signals. This is used with progressive-scan video equipment such as progressive-scan DVD players and high end HDTV decoders. ‰ Y/CB/CR: Terminal is for standard component video input (Y/CB/CR) video signals and stereo sound signals. É RF: This terminal is for connect RF antenna or cable TV box. µ ´ ² VTR/LD RF PC/NOTEBOOK AC IN RGB IN R L RGB OUT AUDIO R- AUDIO- L AV 1 R Y R L OUT L CB CR R L VIDEO IN Y PB PR ˆ AUDIO IN AV COMPONENT OTHER RGB MONITOR DVD PLAYER SET TOP BOX „ ¬ ‚ ƒ R L S-VIDEO 3 ±

-6- NOTE: l Before connecting any cables, refer to the safety instructions at the beginning of this manual and make sure the unit and the video equipment are both switched off. l Be sure to lug the AC power cord to a properly grounded outlet. l The AV OUT terminal only supplies AV1 or AV2 composite signals and does not supply Y/PB/PR or Y/CB/CR signals.

-7- 5 6 3 4 WOOFER DI SPLAY RECALL WI DE CCD AI R CABLE DEGAUSS BLUE BACK ON/OFF CH ADD/ERASE FULL SEARCH 1 7 18 5 10 12 11 2 8 16 14 13 3 20 9 21 15 6 4 17 19

-8- This television features “Digital Vision”, an advanced on-screen digital display and control system to adjust various settings within the television. These functions are accessible using the remote control for the televison’ s front control panels. 1. Pressing the POWER button turns on the unit. When power is on, the green POWER LED illuminates. When power is off, the unit switches to standby mode illuminating the red STANDBY LED. 2. Press button to select the source signal to display. Each time the input button is pressed, the on-screen display will toggle between “TV”, “AV1”, “AV2”, S-VIDEO 3 , “Y/CB/CR”, “Y/PB/PR”, and “RGB”. 3. Use the AIR/CABLE button to switch the tuner from receiving standard over the air broadcasts or standard cable television broadcasts. If AIR is selected, the TV can receive channels 2 to 69. If CABLE is selected, the TV can receive channels 1 to 125. 4. Use the FULL SEARCH button to automatically program the television to receive broadcasts from all available channels. When this button is pushed for 1.5 seconds, the TV will begin the FULL SEARCH process and memorize all available channels. The search takes some time and you can cancel the search by pressing the FULL SEARCH button during the search. Note: l If the tuner is set to AIR (see above), the search range is from CH2 to CH69. If the tuner is set to CABLE TV, the search range is from CH1 to CH125. l The searching data for AIR TV mode and CABLE TV mode is independent. So the FULL SEARCH function must be performed twice, once in AIR mode and once in CABLE TV mode. 5. Push “▲” and “▼“ to change channels. The television will automatically skip blank channels. POWER INPUT SELECT AIR CABLE FULL SEARCH CH s t

-9- 6. This button is used to add a channel to memory or erase a channel stored in memory. With the channel that you want to add or erase selected and displayed on the screen, press the CH ADD/ERASE button. The screen will display “ADD” or “ERASE”. If “ADD” is displayed, it means that this channel can be added to memory and selectable using the channel ▲▼buttons. If “ERASE” is displayed, it means that this channel is erasable from memory and will not be accessible using the channel ▲▼ buttons. 7. Digit Keypad Use the digit keypad to select TV channels. Push any two digits on the keypad to select channels between CH1 and CH99. For example, to select CH2, simply push “0” and “2”. You may also select a single-digit channel between CH2 and CH9 by simply pressing the corresponding digit key. When a single digit is pressed, the TV will wait for 5 seconds before changing the channel. To select channels beyond CH100, push the “100” key first followed by the last two digits of the channel. For example, to select CH107, push “100”, “0”, and ”7”. 8. QV (Quick View) button allows you to instantly revert back to the previously selected channel. 9. Use CCD to set closed caption mode. The CCD button toggles between the following modes: 10. Press and hold the Volume + button to increase the volume level. Press and hold volume - button to decrease the volume level. The Volume +/- buttons also function as ADJ +/- buttons for the On-Screen display functions CH ADD/ERASE QV CLOSED CAPTION OFF COLSED CAPTION 1 COLSED CAPTION 2 TEXT1 TEXT2 CCD ＋ － VOL 1 2 3 4 5 6 7 8 9 0 100

-10- 11. Use MTS to toggle between SAP, MONO, or STEREO audio mode settings for your television program. SAP, MONO, and STEREO audio modes are only applicable to standard television broadcasts. 12. Use MUTE button to quickly turn off the sound through the TV’ s internal speakers. Once pushed, the on-screen display will indicate the mute function is enabled. To disable the mute function, press the button again. The on-screen display will disappear and sound will be restored from the speakers. 13. Push this button to enable/disable the blue back function. The blue back function is used to suppress “snowflakes” and audible noise when the television cannot receive a TV broadcast signal. This funtion is only applicable to analog TV receptions. 14. Use DISPLAY button to show channel information on the screen. 15. The built-in woofer can add a significant bass boost to the sound of your television/monitor. Press WOOFER button to switch the built-in woofer ON or OFF . Each time the button is pressed, the on-screen display will display “woofer on” or “woofer off”. 16. Degaussing keeps the display free from unwanted magnetism that can result in color impurity. Each time the monitor is turned on, it is automatically degaussed. If the unit is displayed continuously, It is recommended that unit is degaussed at least once every few days to remove any color impurities. Whenever the degauss button is pushed, the display image blurs and a humming sound is heard. This is normal. The screen will return to normal operations in a matter of seconds. A minimum of 20 minutes should be observed between each use of the manual degauss button. MTS MUTE BLUE BACK ON/OFF DISPLAY WOOFER DEGAUSS

-11- 17. V-CHIP V-CHIP (Parental Guide) This television is equipped with V-CHIP technology to prevent children from watching unsuitable programming. To setup V-CHIP: 1. Press V-CHIP (blue) key on remote control to enter Parental Guide setting. Your television will display the following: 2. Press the following number keys on the remote control to enter the initial parental code: 8,4,8,4,100. After pressing the code, the screen will display “Parental Guide ON”.to indicate the function is currently switched on. 3. Press V-CHIP (blue) key to go into the next menu to setup parental control settings. The following menu is displayed: Menu Code Reference FV : Fantasy Violence D : Sexual Dialog L : Adult Language S : Sexual Situations V : Violence TV-Y : All Children TV-Y7 : Older Children TV-G : General Audience TV-PG :Guidance Suggested TV-14 : Strongly Cautioned TV-MA : Mature Audience Enter Parental code ----- Parental Guide ON/OFF Set Page+ Parental Guidelines Rating FV V S L D TV-Y u TV-Y7 u u TV-G u TV-PG u u u u u TV-14 u u u u u TV-MA u u u u Set ▼ ▲ Page+ V-CHIP 1 2 3 4 5 6 7 8 9 0 100

-12- 4. Use s(yellow) or t(green) keys to select the rating you want to set. The selected rating will flash to indicate your selection. Use SET (red) key to toggle between the U (unblock) setting or B (block) setting. 5. Press V-CHIP (blue) key again to access the Motion Picture Association of America (MPAA) menu. The MPAA rating menu will display as follows: Menu Code Reference G : General Audience PG : Parental Guidance PG-13 : Strongly Cautioned R : Restricted NC-17 : No One Under 17 X : No One Under 17 6. Use s(yellow) or t(green) keys to select the MPAA rating you wish to set. The selected rating will flash to indicate your selection. Use SET (red) key to toggle between the U (unblock) setting or B (block) setting. t SET s Parental Guidelines Rating FV V S L D TV-Y U TV-Y7 U U TV-G U TV-PG B B B B B TV-14 B B B B B TV-MA B B B B Set ▼ ▲ Page+ V-CHIP MPAA Rating Movie Ratings G U PG U PG-13 U R U NC-17 U X U Set ▼ ▲ Page+ t SET s MPAA Rating Movie Ratings G u PG u PG-13 u R B NC-17 B X B Set ▼ ▲ Page+

-13- 7. After the above setting is completed, press V-CHIP (blue) key to set the parental code. 8. Enter a new passcode using the digit keys on the remote control. The pass code must be 5 digits. When you’ ve completed entering the 5-digit code, press V-CHIP (blue) key to complete the process. You can also keep the original passcode by not entering a new pass code and pressing the V-CHIP (blue) key. Note: If the pass code is forgetten, use the initial pass code of 8,4,8,4,100. This is a master code that will override the system. 9. When watching a channel or program that is blocked by the V-CHIP, the following screens will display: V-CHIP Set Parental code ＊＊＊＊＊ Parental Guide ACCOMPLISHED Blocked 13 Parental Guidelines V-PG VS Blocked 13 MPAA Rating MPAA NC-17 V-CHIP 1 2 3 4 5 6 7 8 9 0 100

-14- 18. For SME-34WHD5 Only When the source of display is AV1 or AV2 or Y/CB/CR, press the WIDE button to select the display aspect ratio. Each time the WIDE button is pressed, the on-screen display will toggle between “4:3” and “16:9”. 19. To display the monitor’ s on-screen display, press menu ▲▼ button. The first line of the window displays the master picture menu and the setting of a selected feature. The last line of the window reports the current resolution and frequency settings. 20. After you have selected a category, you can increase or decrease a display setting. Here’ s how to adjust a setting: Press the menu ▲▼ button. While the master picture menu is on screen, use the menu ▲▼ select key to choose a category. Once you have selected a category, press the ADJ 34button. Each time the ADJ 4button is pressed, the settings for the category selected will increase. Each time the ADJ 3 button is pressed, the settings for the selected category will decrease. 21. Press RECALL button to reset various settings to the factory’ s pre-set default value. RECALL function is not supported when the unit is using RGB or Y/PB/PR as the input source. WIDE ▲ ▼ MENU ADJ. ▲ ▲ RECALL

-15- Open the cover on the back of the remote insert two R06/AA/SUM-3 batteries. Be sure the polarity is correct. Replace the cover. NOTES : To avoid damage from possible battery leakage, remove the batteries for extended unused periods. Be sure that there are no obstructions between the Remote Control and the monitor. Operating range is specified for normal use. The shorter the distance between the Remote control and the monitor narrower the angle within which the Remote Control can operate the monitor. ▲

-16- Front View NOTE: l Before connecting any cables to the AV2 IN terminals, make sure the unit and the video equipment are both switched off. INPUT SELECT DEGAUSS － MENU ＋ － VOL ＋ STAND BY POWER SAVING POWER L-AUDIO-R VIDEO S-VIDEO 3ADJUST4 AV2 IN INPUT SELECT DEGAUSS － MENU ＋ － VOL ＋ L-AUDIO-R VIDEO S-VIDEO 3ADJUST4 AV2 IN STAND BY¯ POWER SAVING ¯ POWER¯ 36”(34” Viewable) 16:9 MONITOR 34” (32” Viewable) 4:3 MONITOR 29” (27” Viewable) 4:3 MONITOR ADJU DEGA － VOL ＋ － MENU ＋ INPUT SELECT STA POWER SAVING ¯ POWER¯ L-AUDIO-R S-VIDEO AV2 IN

-17- 1. Pressing the POWER button turns on the unit. When power is on, the green POWER LED illuminates. When power is off, the unit switches to standby mode illuminating the red STANDBY LED. 2. To display the monitor’ s on-screen display, press menu +/- button. The first line of the window displays the master picture menu and the setting of a selected feature. The last line of the window reports the current resolution and frequency settings. 3. The VOLUME -/+ buttons turns up the volume of your TV/monitor. These buttons also function as the ADJ - / + buttons for setting TV/Monitor settings. 4. Degaussing keeps the display free from unwanted magnetism that can result in color impurity. Each time the monitor is turned on, it is automatically degaussed. If the unit is displayed continuously, It is recommended that unit is degaussed at least once every few days to remove any color impurities. Whenever the degauss button is pushed, the display image blurs and a humming sound is heard. This is normal. The screen will return to normal operations in a matter of seconds. A minimum of 20 minutes should be observed between each use of the manual degauss button. 5. Press button to select the source of display. Each time the input button is pressed, the on-screen display will toggle between “AV1”, “AV2”, S-VIDEO 3, “Y/CB/CR”, “Y/PB/PR”, and “RGB”. POWER MENU ADJ DEGAUSS INPUT SELECT AV1→AV2→S-VIDEO 3→YCBCR→YPBPR→RGB

-18- The TV/Monitor function settings are set using the on-screen display. To access function settings, simply press the MENU - / + keys on the front control panel or your remote control. Different function settings are available for the different types of signal inputs. The following diagram shows the different on-screen displays available for different input signals. On-Screen Display for RGB Input TV and Composite Video Inputs (AV1 and AV2) Std. Component Input (Y/CB/CR) M : 0 1 F H : 3 1 K H z F V : 6 0 H z 1 2 8 BRIGHT M : T V / A V F H : 1 5 K H z F V : 6 0 H z 1 2 8 R←→B BRIGHT M : Y C B C R F H : 1 5 K H z F V : 6 0 H z 1 2 8 R←→B BRIGHT

-19- Progressive Scan Component Inputs (Y/PB/PR) To change the setting of a particular function, you must first highlight the function by pressing the MENU -/+ buttons while the OSD is displayed. This will toggle between the displayed functions. After selecting the function to set, press the ADJ + or ADJ – buttons to adjust the function setting. Each time the ADJ + button is pressed, the settings for the function will increase. Each time the ADJ – button is pressed, the setting for the category will decrease. The following explains the each function setting: BRIGHTNESS: Select icon to adjust the overall picture brightness (image black level). Set the brightness so that the dark areas of the monitor remain black. Press the ADJ - button to decrease brightness. Press the ADJ + button to increase brightness. This setting is available to all video signal inputs. CONTRAST: Select icon to adjust the contrast (image white level). Contrast is the difference in brightness between the dark and light parts of the displayed image. Press the ADJ- button to decrease contrast. Press the ADJ + button to increase contrast. This setting is available to all video signal inputs. V-SIZE (Vertical Size): Select icon to adjust the vertical size of the displayed image. Press the ADJ - button to decrease V-Size. Press the ADJ + button to increase V-Size. This setting is only available to RGB and Y/PB/PR input signals. V-CENTER (Vertical Position): Select icon to adjust the vertical position of the displayed image. Press the ADJ- button to decrease V-Position. Press the ADJ+ button to increase V-Position. This setting is only available to RGB and Y/PB/PR input signals. 1 2 8 R←→B COLOR M: YPBPR FH :33KHz FV : 60Hz 1 2 8 BRIGHT M: YPBPR FH : 33KHz FV : 60Hz

-20- H-WIDTH (Horizontal Size): Select icon to adjust the horizontal size of the displayed image. Press the ADJ- button to decrease H-Width. Press the ADJ + button to increase H-Width. This setting is only available to RGB and Y/PB/PR input signals. H-PHASE (Horizontal Position):. Select icon to adjust the horizontal position of the displayed image. Press the ADJ- button to decrease H-Phase. Press the ADJ + button to increase H-Phase. This setting is only available to RGB and Y/PB/PR input signals. PINCUSHION: Select icon to adjust the amount of tapering on each side of the displayed image. Press the ADJ- button to decrease the amount of side pincushion. Press the ADJ + button to increase the amount of side pincushion. This setting is only available to RGB and Y/PB/PR input signals. TRAPEZOID: Select icon to adjust the trapezoid. Press ADJ - button to move the upper screen to center and to move the lower screen to the outside. Press ADJ + button to move the upper screen to the outside and to move the lower screen to the center. This setting is only available to RGB and Y/PB/PR input signals. PARALLELOGRAM: Select icon to adjust the parallelogram. Press ADJ + button to slant the screen to left side and press ADJ - button to slant the screen to right side. This setting is only available to RGB and Y/PB/PR input signals. ROTATION: Select icon to adjust the screen tilt of the displayed image. This is used to compensate for earth magnetic field effect on the monitor. This setting is only available to RGB and Y/PB/PR input signals. R-GAIN: Select icon to change the gain of red. G-GAIN: Select t icon to change the gain of green. B-GAIN: Select icon to change the gain of blue. These settings are available to all video signal inputs. BASS: Select icon to adjust bass level of sound. TREBLE: Select icon to adjust treble level of sound. BALANCE: Select icon to adjust the left and the right balance. These settings are available to all video signal inputs. COLOR: Select icon to adjust the color of the displayed image. Press the ADJ - button to decrease color. Press the ADJ + button to increase color. This setting is available to TV/AV (Composite video AV1 & AV2), Y/CB/CR and Y/PB/PR signal inputs. TINT: Select icon to adjust the tint of the displayed image. Press the ADJ + button to increase the level of green in the image. Press the ADJ - button to increase the level of red in the image. This setting is available to TV/AV (Composite video AV1 & AV2), Y/CB/CR and Y/PB/PR signal inputs. This function is not applicable with PAL video signals. SHARPNESS:Select icon to adjust the sharpness of the displayed image.Press the ADJ - button to decrease sharpness.Press the ADJ + button to increase sharpness.This setting is available to TV/AV (Composite video AV1 & AV2), Y/CB/CR and Y/PB/PR signal inputs. R←→ B

-21- The following is a description of the power states and the power consumed in each state: MODE LED H-SYNC V-SYNC VIDEO POWER CONSUMPTION on green pulse pulse active normal power saving yellow no pulse pulse blanked <30W power saving yellow pulse no pulse blanked <30W power saving yellow no pulse no pulse blanked <30W NOTE: l The power management function requires TTL horizontal and vertical sync. l Power saving is invalid if display is in TV, AV, Y CB CR, Y PB PR mode. As an ENERGY STAR® partner, SAMPO CORPORATION has determined that this product meets the ENERGY STAR®guidelines for energy efficiency.

Trouble condition Cause Remedy No picture 1. Power cord disconnected. 2. Power not switched on. 3. Improperly connected signal cable. 4. Monitor in power save mode. 1. Connect power cord. 2. Turn the power switch on. 3. Connect the signal properly. 4. Press any key on computer. Color is abnormal 1. Magnetic object nearby. 2. Direction of screen changed during operation. 3. Improperly connected signal cable. 1. Move the magnetic object away. 2. Turn OFF the power switch and wait 10 minutes. Turn on the power and degauss circuit within monitor. 3. Connect signal cable properly. Picture runs 1. Improperly connected signal cable. 2. Input signal frequency is being the normal operating range of the monitor. 1. Connect signal cable properly. 2. Readjust your input signal to within the normal frequency range of the monitor. Display image is too dark 1. Brightness and contrast settings set at minimum. 1. Adjust brightness and contrast. Display image is too large or small 1. Horizontal size control needs adjustment. 2. Vertical size control needs adjustment. 1. Use the horizontal size control function setting to adjust the image to desired size. 2. Use the vertical size control function setting to adjust the image to desired size. Image is distorted 1. Earth’ s natural magnetic field interfering with display. 2. Picture appears or 1. Use the rotation function setting to adjust the image. 2. Use the pincushion function setting to adjust the image. Remote control is not functioning 1. Weak or dead batteries. 2. Outside interference. 1. Replace batteries. 2. Turn off the TV and disconnect the AC power cord from the fall. Wait 10 seconds and reconnect the AC power cord. Turn on the television again. With sound no picture 1. Antenna direction changed? 2. Antenna a properly connected? 1. To verify the direction of antenna. 2. To verify whether the cable was connected in properly. With picture no sound 1. Antenna has trouble? 2. Volume adjust to min.? 3. Without connecting audio cable? 4. Non-integrate signal proanced? 1. To verify the direction of antenna. 2. To adjust the volume in properly. 3. To connect the audio cable in properly. 4. Try other channels. No picture just blue back 1. Antenna properly connected? 2. Non-integrate signal proanced? 1. To verify the direction of antenna. 2. Try other channels. Picture repeat 1. The location of antenna is appropriately? 1. The reflex wave is effected by mountain building and tree to cause picture repeat. Try to change the direction and highness of antenna. Appear cross line 1. Effect by other station . 1. Try to change the direction and highness of antenna Picture with snowflakes and noise. 1. Antenna has trouble ? 2. Antenna properly connected ? 3. Antenna direction changed ? 1. To verify the direction of antenna. 2. To verify whether the cable was connected in properly. 3. To verify the direction of antenna.

FREQUENCY TABLE -24- Band AIR CB CATV CH FP (MHZ) Assig- nment CH DISP FP (MHZ) CH DISP CB NO STD BRC IRC VHF 02 55.25 02 2 55.25 54.00 55.25 LOW 03 61.25 03 3 61.25 60.00 61.25 04 67.25 04 4 67.25 66.00 67.25 01 4A …… 72.00 73.25 05 77.25 05 5 77.25 78.00 79.25 06 83.25 06 6 83.25 84.00 85.25 95 A-5 91.25 90.00 91.25 96 A-4 97.25 96.00 97.25 97 A-3 103.25 102.00 103.25 98 A-2 109.25 108.00 109.25 99 A-1 115.25 114.00 115.25 14 A 121.25 120.00 121.25 15 B 127.25 126.00 127.25 VHF 16 C 133.25 132.00 133.25 BIGB 17 D 139.25 138.00 139.25 18 E 145.25 144.00 145.25 19 F 151.25 150.00 151.25 20 G 157.25 156.00 157.25 21 B 163.25 162.00 163.25 22 1 169.25 168.00 169.25 07 175.25 07 7 175.25 174.00 175.25 08 181.25 08 8 181.25 180.00 181.25 09 187.25 09 9 187.25 186.00 187.25 10 193.25 10 10 193.25 192.00 193.25 11 199.25 11 11 199.25 198.00 199.25 12 205.25 12 12 205.25 204.00 205.25 13 211.25 13 13 211.25 210.00 211.25 23 J 217.25 216.00 217.25 24 K 223.25 222.00 223.25 25 L 229.25 228.00 229.25 26 M 235.25 234.00 235.25 27 N 241.25 240.00 241.25 28 O 247.25 246.00 247.27 29 P 253.25 252.00 253.25

FREQUENCY TABLE -25- Band AIR CB CATV CH FP (MHZ) Assig- nment CH DISP FP (MHZ) CH DISP CB NO STD BRC IRC 30 Q 259.25 258.00 259.25 31 R 265.25 264.00 265.25 32 S 271.25 270.00 271.25 33 T 277.25 276.00 277.25 34 U 283.25 282.00 283.25 35 V 289.25 288.00 289.25 36 W 295.25 292.00 295.25 37 +1 301.25 300.00 301.25 38 +2 307.25 306.00 307.25 39 +3 313.25 312.00 313.25 40 +4 319.25 318.00 319.25 41 +5 325.25 324.00 325.25 42 +6 331.25 330.00 331.25 43 +7 337.25 336.00 337.25 44 +8 343.25 342.00 343.25 45 +9 349.25 348.00 349.25 46 +10 355.25 354.00 355.25 47 +11 361.25 360.00 361.25 48 +12 367.25 366.00 367.25 49 +13 375.25 372.00 373.25 50 +14 379.25 378.00 379.25 51 +15 385.25 384.00 385.25 52 +16 391.25 390.00 391.25 53 +17 397.25 396.00 397.25 54 +18 403.25 402.00 403.25 55 +19 409.25 408.00 409.25 56 +20 415.25 414.00 415.25 57 +21 421.25 420.00 421.25 58 +22 427.25 426.00 427.25 UHF 59 V+23 433.25 432.00 433.25 60 V+24 439.25 438.00 439.25 61 V+25 445.25 444.00 445.25 62 V+26 451.25 450.00 451.25 63 V+27 457.25 456.00 457.25 64 V+28 463.25 462.00 463.25 65 V+29 469.25 468.00 469.25 14 471.25 66 V+30 475.25 474.00 475.25 15 477.25 67 V+31 481.25 480.00 481.25 16 483.25 68 V+32 487.25 486.00 487.25 17 489.25 69 V+33 493.25 492.00 493.25 18 495.25 70 V+34 499.25 498.00 499.25 19 501.25 71 V+35 505.25 504.00 505.25 20 507.25 72 V+36 511.25 510.00 511.25 21 513.25 73 V+37 517.25 516.00 517.25

FREQUENCY TABLE -26- Band AIR CH CATV CH FP (MHZ) Assig- nment CH DISP FP (MHZ) CH DISP CB NO STD BRC IRC 22 519.25 74 V+38 523.25 522.00 523.25 23 525.25 75 V+39 529.25 528.00 529.25 24 531.25 76 V+40 535.25 534.00 535.25 25 537.25 77 V+41 541.25 540.00 541.25 26 543.25 78 V+42 547.25 546.00 547.25 27 549.25 79 V+43 553.25 552.00 553.25 28 555.25 80 V+44 559.25 558.00 559.25 29 561.25 81 V+45 565.25 564.00 565.25 30 567.25 82 V+46 571.25 570.00 571.25 31 573.25 83 V+47 577.25 576.00 577.25 32 579.25 84 V+48 583.25 582.00 583.25 33 585.25 85 V+49 589.25 588.00 589.25 34 591.25 86 V+50 595.25 594.00 595.25 35 597.25 87 V+51 601.25 600.00 601.25 36 603.25 88 V+52 607.25 606.00 607.25 37 609.25 89 V+53 613.25 612.00 613.25 38 615.25 90 V+54 619.25 618.00 619.25 39 621.25 91 V+55 625.25 624.00 625.25 40 627.25 92 V+56 631.25 630.00 631.25 41 633.25 93 V+57 637.25 636.00 637.25 42 639.25 94 V+58 643.25 642.00 643.25 43 645.25 100 V+59 649.25 648.00 649.25 44 651.25 101 V+60 655.25 654.00 655.25 45 657.25 102 V+61 661.25 660.00 661.25 46 663.25 103 V+62 667.25 666.00 667.25 47 669.25 104 V+63 673.25 672.00 673.25 48 675.25 105 V+64 679.25 678.00 679.25 49 681.25 106 V+65 685.25 684.00 685.25 50 687.25 107 V+66 691.25 690.00 691.25 51 693.25 108 V+67 697.25 696.00 697.25 52 699.25 109 V+68 703.25 702.00 703.25 53 705.25 110 V+69 709.25 708.00 709.25 54 711.25 111 V+70 715.25 714.00 715.25 55 717.25 112 V+71 721.25 720.00 721.25 56 723.25 113 V+72 727.25 726.00 727.25 57 729.25 114 V+73 733.25 732.00 733.25 58 735.25 115 V+74 739.25 738.00 739.25 59 741.25 116 V+75 745.25 744.00 745.25 60 747.25 117 V+76 751.25 750.00 751.25 61 753.25 118 V+77 757.25 756.00 757.25 62 759.25 119 V+78 763.25 762.00 763.25 63 765.25 120 V+79 769.25 768.00 769.25 64 771.25 121 V+80 775.25 774.00 775.25 65 777.25 122 V+81 781.25 780.00 781.25 66 783.25 123 V+82 787.25 786.00 787.25 67 789.25 124 V+83 793.25 792.00 793.25 68 795.25 125 V+84 799.25 798.00 795.25 69 801.25

a. tube size 36 inch (16:9 Aspect Ratio) 34 inch (32 inch viewable) 29 inch (27 inch viewable) b. Dot pitch H=0.82mm H=0.8mm H=0.74mm c. Light transmission 76% (typical) 35% typical 49% typical 2. Power a. Input voltage 100 Vac ~ 240 Vac 60Hz / 50Hz 100 Vac ~ 240 Vac 60Hz / 50Hz 100 Vac ~ 240 Vac 60Hz / 50Hz b. Input current 3A at 110Vac / 60Hz Max 3A at 110Vac / 60Hz Max 3A at 110Vac / 60Hz Max c. Power consumption 200 Watts(Max) 220 Watts(Max) 180 Watts(Max) 3. Input signal Video signal a. Type Analog Analog Analog b. Polarity Positive Positive Positive c. Amplitude RGB: 0.714 Vp-p Y PB PR: 1Vp-p (with sync) AV: 1Vp-p (with sync) Y CB CR: 1Vp-p (with sync) RGB: 0.714 Vp-p Y PB PR: 1Vp-p (with sync) AV: 1Vp-p (with sync) Y CB CR: 1Vp-p (with sync) RGB: 0.714 Vp-p Y PB PR: 1Vp-p (with sync) AV: 1Vp-p (with sync) Y CB CR: 1Vp-p (with sync) d. Input impedance 75 ohms 75 ohms 75 ohms e. Dot rate 75 MHz(Max.) 75 MHz(Max.) 75 MHz(Max.) Audio Signal a. Type Analog Analog Analog b. Polarity 1.0Vp-p 1.0Vp-p 1.0Vp-p c. Amplitude ≧10KΩ ≧10KΩ ≧10KΩ Horizontal sync a. Type TTL TTL TTL b. Polarity Positive or negative Positive or negative Positive or negative c. Input impedance 1K ohm(Min) 1K ohm(Min) 1K ohm(Min) d. Frequency RGB: 31 KHz ~ 52 KHz Y PB PR: 31KHz~45KHz AV/Y CB CR: 15.734 KHz (NTSC) 15.625 KHz (PAL) RGB: 31 KHz ~ 52 KHz Y PB PR: 31KHz~45KHz AV/Y CB CR: 15.734 KHz (NTSC) 15.625 KHz (PAL) RGB: 31 KHz ~ 52 KHz Y PB PR: 31KHz~45KHz AV/Y CB CR: 15.734 KHz (NTSC) 15.625 KHz (PAL) Vertical sync a. Type TTL TTL TTL b. Polarity Positive or negative Positive or negative Positive or negative c. Input impedance 1K ohm(Min) 1K ohm(Min) 1K ohm(Min) d. Frequency RGB: 50 Hz ~ 120 Hz Y PB PR: 60 Hz AV/Y CB CR: 60 Hz (NTSC) 50 Hz (PAL) RGB: 50 Hz ~ 120 Hz Y PB PR: 60 Hz AV/Y CB CR: 60 Hz (NTSC) 50 Hz (PAL) RGB: 50 Hz ~ 120 Hz Y PB PR: 60 Hz AV/Y CB CR: 60 Hz (NTSC) 50 Hz (PAL) 4. Connector type 15 pin D-type and RCA JACK and S-terminal 15 pin D-type and RCA JACK and S-terminal 15 pin D-type and RCA JACK and S-terminal 5. Horizontal size 725 +/- 8 mm (for RGB mode 1-9) 620 +/- 8 mm (for RGB mode 1-9) 520 +/- 6 mm (for RGB mode 1-9) Vertical size 408 +/- 8 mm (for RGB mode 1-9) 465 +/- 8 mm (for RGB mode 1-9) 388 +/- 6 mm (for RGB mode 1-9)

W× H × D (mm) 1000 × 636 × 695 866 × 718 × 583 742 × 575 × 512 Packaging dimension : W× H × D (mm) 1165 × 870 × 900 1030 × 870 × 760 880 × 647 × 580 7. Net weight of unit : 87 Kg 71 Kg 51 Kg 8. User Controls: Power, Brightness, Contrast, V-Size, V-Center, H-Width, H-Phase, Degauss, Pincushion, Trapezoid, Parallelogram, Rotation, R-Gain, G-Gain, B-Gain, Bass, Treble, Balance, Color, Tint, Sharpness, Mute, Volume, Woofer, Recall, Input Select, WIDE. 9. Operating temperature: 0℃ to 40℃ 10. Pin assignments for D-type connector Pin 1 : RED Pin 6 : RED RETURN Pin 11 : GND Pin 2 : GREEN Pin 7 : GREEN RETURN Pin 12 : SDA Pin 3 : BLUE Pin 8 : BLUE RETURN Pin 13 : H-SYNC Pin 4 : GND Pin 9 : NC Pin 14 : V-SYNC Pin 5 : GND Pin10: GND Pin 15 : SCL 11. a. The table below is required timings and technical description for the 36” tube (H=725mm, V=408mm standard size), 34” tube (H=620mm, V=465mm standard size), 29” tube (H=520mm, V=388mm standard size). Mode No. 1 2 3 4 5 6 7 8 9 HDTV HDTV‚ Resolution & Refresh Rate 640 480 60 640 480 72 720 400 70 640 480 66.6 800 600 60.317 800 600 56.25 640 480 85 800 600 72 1024 768 60 1280 720 60 1920 1080 60 Hz Pixel timing +/- .5% 39.722 31.746 35.311 33.06 25 27.8 36 50 15.385 13.468 13.468 n Sec Horizontal visible 640 640 720 640 800 800 640 800 1024 1280 1920 Dots Horizontal total 800 832 900 864 1056 1024 832 1040 1344 1650 2200 Dots Horizontal front porch 16 16 18 64 40 24 56 56 40 112 80 Dots Horizontal sync 96 40 108 64 128 72 56 120 145 76 76 Dots Horizontal back porch 48 136 54 96 88 128 80 64 105 72 36 Dots Hor blanking time 160 192 180 224 256 224 192 240 290 260 192 Dots Vertical visible 480 480 400 480 600 600 480 601 768 720 1080 Lines Vertical total 525 520 449 525 628 625 509 667 806 750 1125 Lines Vertical front porch 10 1 12 3 1 1 1 1 1 5 2 Lines Vertical sync 2 3 2 3 4 2 3 6 6 5 5 Lines Vertical back porch 33 36 35 39 23 22 22 23 29 20 15 Lines Vertical blanking time 45 40 49 45 28 25 26 30 36 30 22 Lines Horizontal frequency 31.469 37.861 31.467 35 37.879 35.156 43.27 48.09 48.363 45.1515 33.78 KHz Vertical frequency 59.940 72.809 70.082 66.667 60.317 56.250 85 72 60 60 60 Hz Vertical sync polarity - - + - + + - + - - - TTL Hor sync polarity - - - + + + - + - - - TTL Dot rate 25.2 31.2 28.3 30.204 40 35.97 36 50 65 74.25 74.25 MHz The SYNC-ON-GREEN recall is just proper MODE 4. b.YPBPR mode: mode 1 : 1080I (H=33KHz, V=60Hz) mode 2 : 720p (H=45KHz, V=60Hz)