JVC HR-J655EK Instructions Manual

INSTRUCTIONS LPT0052-001B PAL TV PR OG + TV PR OG – T V – T V + TV 0000 START DEBUT STOP FIN DATE MENU OK TV PROG TV/VCR DAILY/QTDN. VPS/PDC AUX ? WEEKLY/HEBDO PROG 30 SEC – –:– – AUDIO 1 2 3 4 5 6 7 8 9 0 2 4 1 3 EXPRESS DISPLAY REC LINK COUNTER RESET TV PROG TV PROG TIMER STANDBY/ON SP/LP PUSH JOG CONTENTS SAFETY FIRST 2 Safety Precautions ...................... 2 Some Do's And Don'ts ............... 3 QUICK SET UP GUIDE 4 CHECK THE CONTENTS ........... 4 INSTALLATION .......................... 5 AUTO SET UP............................ 6 BASIC OPERATIONS 8 Playback .................................... 8 Recording ................................ 10 Video Plus+ Timer Programming ........................... 12 Express Timer Programming ..... 14 ADVANCED OPERATIONS 17 Looking For The Scene You Want ................................. 17 Playback/Recording According To Tape Characteristics............. 18 Playback Picture Adjustment .... 20 Selecting The Sound You Want ........................................ 21 Automatic Satellite Programme Recording ................................ 22 Edit To Or From Another Video Recorder .................................. 24 Edit From A Camcorder ............ 25 Other Functions ....................... 26 SYSTEM CONNECTIONS 29 Connection To A Stereo System ..................................... 29 SUBSIDIARY SETTINGS 30 Video Channel Set ................... 30 Tuner Set .................................. 32 Clock Set ................................. 39 Video Plus+ Setup .................... 40 SUBSIDIARY INFORMATION 41 Questions And Answers ........... 41 Troubleshooting ....................... 42 Index ....................................... 44 SPECIFICATIONS Back Cover

instruction manual before installing or operating the recorder. n It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video record- ing, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein. IMPORTANT Connection to the mains supply in the United Kingdom. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain a proper safety approved extension lead/adapter or consult your dealer. In the unlikely event of the plug fuse failing be sure to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover. If the fuse fails again consult your nearest JVC dealer. If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. If this product is not supplied fitted with a mains plug then follow the instructions given below: DO NOT make any connection to the Larger Terminal coded E or Green. The wires in the mains lead are coloured in accordance with the following code: If these colours do not correspond with the terminal identifications of your plug, connect as follows: Blue wire to terminal coded N (Neutral) or coloured Black. Brown wire to terminal coded L (Live) or coloured Red. If in doubt — consult a competent electrician. Blue to N (Neutral) or Black Brown to L (Live) or Red CAUTION n When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet. n Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial. The rating plate and the safety caution are on the rear of the unit. WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. Safety Precautions Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a single-speed video recorder. The STANDBY/ON button does not completely shut off mains power from the unit, but switches operating current on and off. " " shows electrical power standby and " " shows ON. Failure to heed the following precautions may result in damage to the recorder, remote control or video cassette. 1. DO NOT place the recorder . . . ... in an environment prone to extreme temperatures or humidity. ... in direct sunlight. ... in a dusty environment. ... in an environment where strong magnetic fields are generated. ... on a surface that is unstable or subject to vibration. 2. DO NOT block the recorder’s ventilation openings. 3. DO NOT place heavy objects on the recorder or remote control. 4. DO NOT place anything which might spill on top of the recorder or remote control. 5. AVOID violent shocks to the recorder during transport. MOISTURE CONDENSATION Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the recorder turned on for a few hours to let the moisture dry. ABOUT HEAD CLEANING Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or inter- rupted. Be sure to contact your nearest JVC dealer if such troubles occur. n Cassettes marked "VHS" (or "S-VHS") can be used with this video recorder. However, only VHS recordings can be made and played back. n HQ VHS is compatible with existing VHS equipment. n Video Plus+ and PlusCode are trademarks of Gemstar Development Corporation. The Video Plus+ system is manufactured under license from Gemstar Development Corporation. PAL

electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment. DO ensure that all electrical connections (including the mains plug, extension leads and interconnec- tions between pieces of equipment) are properly made and in accordance with the manufacturer's instructions. Switch off and withdraw the mains plug when making or changing connections. DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equip- ment. DO be careful with glass panels or doors on equipment. DON'T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way — switch off, withdraw the mains plug and consult your dealer. DON'T remove any fixed cover as this may expose dangerous voltages. DON'T leave equipment switched on when it is unattended unless it is specifically stated that it is de- signed for unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your family knows how to do this. Special arrangements may need to be made for infirm or handicapped people. DON'T use equipment such as personal stereos or radios so that you are distracted from the requirements of road safety. It is illegal to watch television whilst driving. DON'T listen to headphones at high volume, as such use can permanently damage your hearing. DON'T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheat- ing will cause damage and shorten the life of the equipment. DON'T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer's approved stand or legs with the fixings provided according to the instruc- tions. DON'T allow electrical equipment to be exposed to rain or moisture. ABOVE ALL... — NEVER let anyone especially children push anything into holes, slots or any other opening in the case — this could result in a fatal electrical shock; — NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry! Some Do's And Don'ts On The Safe Use Of Equipment

TV PR OG + TV PR OG – T V – T V + TV 0000 START DEBUT STOP FIN DATE MENU OK TV PROG TV/VCR DAILY/QTDN. VPS/PDC AUX ? WEEKLY/HEBDO PROG 30 SEC – –:– – AUDIO 1 2 3 4 5 6 7 8 9 0 2 4 1 3 EXPRESS STEP 1 CHECK THE CONTENTS CHECK ALL THE CONTENTS SHOWN BELOW Dear Customer, Thank you for purchasing this JVC Video Cassette Recorder. Please use this QUICK SET UP GUIDE to help you to set up your video cassette recorder. Video Cassette Recorder Infrared Remote Control Unit RF Cable "AA" Batteries (x 2) DISPLAY REC LINK COUNTER RESET TV PROG TV PROG TIMER STANDBY/ON SP/LP PUSH JOG You are now ready to install your video recorder.

(SCART) . . . 1– Connect the aerial, recorder and TV as per “RF CONNECTION”. 2– Connect an optional SCART cable between the AV1 IN/OUT socket on the rear panel of the recorder and the TV’s 21-pin AV input connector (SCART). STEP 2 INSTALLATION CONNECT VIDEO RECORDER TO TV Place the recorder on a stable, flat surface. Make this connection if your TV has a 21-pin AV input connector (SCART) in order to reduce the possibility of interference. And if you are using a stereo TV, you will need this cable in order to enjoy stereo playback of videotapes. RF CONNECTION To Connect To A TV With NO 21-pin AV input connector (SCART) . . . 1– Disconnect the TV aerial cable from the TV. 2– Connect the TV aerial cable to the ANT. IN jack on the rear panel of the recorder. 3– Connect the provided RF cable between the RF OUT jack on the rear panel of the recorder and the TV’s aerial connector. Go to Step 3 – AUTO SET UP AFTER YOU FINISH THIS STEP ATTENTION nDo NOT Plug the mains power cord into a mains outlet until all connections are completed. nDo NOT press the button on the recorder or on the remote control to turn on the recorder's power before you start the Auto Set Up procedure described on page 6. 21-pin AV input connector (SCART) Aerial connector Back of TV 21-pin SCART Cable (not provided) RF Cable (provided) TV Aerial Cable (not provided) Mains Power Cord Back of Recorder Mains outlet

STEP 3 AUTO SET UP SET THE TUNER CHANNELS, CLOCK, GUIDE PROGRAM NUMBERS AND VIDEO CHANNEL* The Auto Set Up function sets the tuner channels, clock, Video Plus+ assigned Guide Program numbers and the video channel* automatically the first time the button on the recorder or on the remote is pressed to turn on the recorder after the mains power cord has been plugged into a mains outlet. Before performing the following procedure, make sure that: n the TV aerial cable is connected to the recorder. n the mains power cord is plugged into the mains outlet. n batteries have been installed in the remote control. 1 ATTENTION Once you have performed Auto Set Up, all the stored stations, Guide Program numbers and the video channel remain in the recorder's memory and the recorder will not perform Auto Set Up again. If there is a power cut and the recorder's memory backup expires you only need to reset the clock. (Z pg. 39) If you have moved to a different area, perform each setting as required. n Video Channel setting (for RF connection users) Z pg. 30 n Tuner setting Z pg. 32 n Clock setting Z pg. 39 If a new station begins broadcasting in your area, perform tuner setting (Z pg. 32) and, if necessary, video channel setting (Z pg. 30). 0 + + + Beginning End * Useful if you have connected the video recorder to your TV via RF connection (Z pg. 5). Video Channel (RF output channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable. NOTES: ●Auto channel set function takes place first; it assigns automatically all receivable stations in your area. ● Auto clock set function sets the clock automatically. ● During auto channel set, the recorder recognizes each station name of the detected stations and stores them in the recorder's memory, then automatically sets the Video Plus+ assigned Guide Program number for those stations according to the broadcast area. ● For RF connection users: The video recorder detects the channels which are not occupied by local stations and selects one channel automatically for your Video Channel that is located in the middle of more than 5 vacant channels. ● If there is power cut or if you press or MENU while Auto Set Up is in progress, Auto Set Up will be inter- rupted; be sure to turn off the recorder power once and press to turn the power back on in order to re-start Auto Set Up. AUTO SET PLEASE WAIT [MENU] : EXIT 2 3 Press OK to finish Auto Set Up and refer to next page to check the results. Press . "Auto" appears on the display panel and blinks; do NOT press any button on the recorder or remote control until the display panel shows either the display as illustrated below in item 2 or "– – :– –". Auto Set Up usually takes about 4 – 12 minutes; the duration varies by area. ●If "– – :– –" appears on the display panel, refer to next page. ●If you have connected the video recorder to your TV via both an RF cable and a 21-pin SCART cable (AV connection) and if the TV is turned on and set to its AV mode, the AUTO SET screen will appear. ●If you have connected the video recorder to your TV via an RF cable only (RF connection) — the channel that is shown on the display panel is your Video Channel. To view picture signals from the video recorder, set your TV to the Video Channel. — Refer to the instructions supplied with your TV set for how to do this. Go to item 3 . ●If you have connected the video recorder to your TV via both an RF cable and a 21-pin SCART cable (AV connection) — you do not need the video channel so you have to set the video channel to off. Press TV PROG – until the display panel shows "_OUT– –" to set the Video Channel to off. To view picture signals from the video recorder, set your TV to its AV mode. — Refer to the instructions supplied with your TV set for how to do this. Go to item 3 .

properly. If the Guide Program numbers are not set properly, when you timer-record a TV programme using Video Plus+, the recorder will record a TV programme of a different station. When programming the timer using Video Plus+, be sure to check that the preset position corresponding to the broadcasting station you wish to record has been selected (Z pg. 12, "Video Plus+ Timer Programming"). n Your video recorder memorizes all detected stations even if reception of some of them is poor. In these cases picture quality may be poor. To delete those stations which have an unacceptable picture Z "Delete A Channel" on page 35. n If any of the above problems occur, refer to pages 34 – 36 to input station names (Z "Set Stations") or delete unnecessary stations (Z "Delete A Channel"). You can also change station preset positions (Z "Change Station Preset Position"). n For RF connection users: In certain reception conditions, the Video Channel may not be set correctly and interference may appear in the TV picture while the recorder's power is on. Set your Video Channel manually. Z pg. 30, "Video Channel Set". Auto Set Up results appear on the display panel When neither auto channel set nor auto clock set has been completed successfully, "– –:– –" will be displayed. * You can check if the Guide Program numbers have been set correctly when you perform Video Plus+ Timer Programming (Z pg. 12); if the correct preset position number is displayed in step 3, this confirms that the Guide Program number for the PlusCode number you enter in step 2 has been set correctly. A If both auto channel set and auto clock set have been performed successfully: 1 Turn on the TV and select its VIDEO channel or AV mode, then make sure that all necessary stations have been stored in the recorder's memory by using the TV PROG button(s). ●If station names (ID — Z pg. 37) have also been stored in the recorder's memory, the station name will be displayed at the top left corner of the screen for about 5 seconds each time the recorder is tuned to a different station. ●If you want to set the tuner manually such as to add or skip channels, to change preset positions, or to set or change station names, see pages 34 – 36. Now you have finished the basic set up and can use your recorder for both playback and recording. B If auto channel set has succeeded but auto clock set has not: 1 Turn on the TV and select its VIDEO channel or AV mode, then make sure that all necessary stations have been stored in the recorder's memory by using the TV PROG button(s). ●If station names (ID — Z pg. 37) have also been stored in the recorder's memory, the station name will be displayed at the top left corner of the screen for about 5 seconds each time the recorder is tuned to a different station. ●If you want to set the tuner manually such as to add or skip channels, to change preset positions, or to set or change station names, see pages 34 – 36. 2 Perform "Clock Set" on page 39. Now you have finished the basic set up and can use your recorder for both playback and recording. C If both auto channel set and auto clock set have failed: 1 Make sure the TV aerial cable is connected properly to the recorder and turn off the recorder power once, then turn the recorder power back on again. ●The recorder will try Auto Set Up again. If you have any difficulty with the above procedures call the JVC Customer Service Hot Line on 0181 208 7654 A B C When both auto channel set and auto clock set have been completed successfully the correct current time will be displayed after the OK button is pressed in item 3 on page 6. When auto channel set has been completed successfully but auto clock set has not, "(PR)1" will be displayed after the OK button is pressed in item 3 on page 6.

recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme. LOAD A CASSETTE 1 Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is point toward the recorder. Don’t apply too much pressure when inserting. ●The recorder power comes on automatically and the counter is reset to 0:00:00. ●If the record safety tab has been removed, playback begins automatically. FIND PROGRAMME START POINT 2 If the tape is advanced past the start point, press REW. To go forward, press FF. START PLAYBACK 3 Press PLAY. "BEST" appears blinking in the recorder's display panel during automatic tracking (Z pg. 18) ●Playback picture quality of LP recordings will not be as high as SP recordings. STOP PLAYBACK 4 Press STOP on the remote or STOP/EJECT on the recorder’s front panel. Then press STOP/EJECT to remove the cassette. Turn on the TV and select the VIDEO channel (or AV mode). 7 8 9 0 4 1 3 ? PLAY STOP 3 4 1 REW 2 FF 2 Usable cassettes ●Compact VHS camcorder recordings can be played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette. ●This video recorder can record on regular VHS and Super VHS cassettes. However, it will record and play back regular VHS signals only. It is not possible to play back a recorded Super VHS tape. 3 4 STOP/EJECT Tape Position Indicator The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “5” in relation to “0” (beginning) or “+” (end) shows you where you are on the tape. ”O.S.D.” (Z pg. 26) must be set to “ON”, or the indicator will not appear. NOTE: Depending on the type of tape used, there may be times when the indication is not correct. 3 1:23:45 REMAIN 2:35 0 + + + Beginning End PLAY REW FF 2 2

1 Press PAUSE. If there is vertical jitter, use the TV PROG buttons to correct the picture. ACTIVATE FRAME-BY-FRAME PLAYBACK 2 Press PAUSE. Each time PAUSE is pressed the tape will advance one frame. OR Press or (™ or £). Each time one of these buttons is pressed the tape will move one frame in the direction of the arrow. To resume normal playback, press PLAY. Slow Motion ACTIVATE SLOW-MOTION PLAYBACK 1 During still picture, press and hold PAUSE for 2 seconds, then release. Press and release again to return to still picture. OR During still picture, press and hold or (™ or £). Release to return to still picture. To resume normal playback, press PLAY. High-Speed Search ACTIVATE HIGH-SPEED SEARCH 1 During playback or still picture, press FF for forward high-speed search, or REW for reverse high-speed search. To resume normal playback, press PLAY. NOTE: For short searches, press and hold FF or REW for more than 2 seconds during playback or still picture. When released, normal playback resumes. % % ACTIVATE VARIABLE-SPEED SEARCH 1 During playback, press or (™ or £). ●The more times you press, the faster the playback picture moves. ●To decrease speed, press the button for the opposite direction. To resume normal playback, press PLAY. Variable-Speed Search ATTENTION In the search, still, slow-motion or frame-by-frame playback mode, ●the picture will be distorted. ●noise bars will appear. ●there will be loss of colour with a tape recorded in LP mode. % % % % PAUSE TV PROG TV PROG PAUSE FF REW PLAY PLAY FF REW

recorded onto a video tape. You can “capture” a TV programme using your video recorder. BASIC OPERATIONS (cont.) Recording Turn on the TV and select the VIDEO channel (or AV mode). LOAD A CASSETTE 1 Insert a cassette with the record safety tab intact (See below). ●The counter is reset to 0:00:00 and the recorder power comes on automatically. CHOOSE A PROGRAMME 2 Press TV PROG +/– or the NUMBER keys to select the preset you wish to record. SET TAPE SPEED 3 Press SP/LP ( ). Check the SP/LP indicator on the recorder display panel to confirm the selected tape speed. ●Picture quality of LP recordings will not be as high as on SP recordings. START RECORDING 4 Press and hold RECORD and press PLAY on the remote control, or press RECORD on the recorder. ● You can not change the preset whilst recording is in progress. To change the preset, see step 5. PAUSE/RESUME RECORDING 5 Press PAUSE. Press PLAY to resume recording. ● During the Record Pause mode, you can change the preset by pressing the TV PROG +/– buttons or the NUMBER keys. STOP RECORDING 6 Press STOP on the remote control or STOP/EJECT on the recorder. Then press STOP/EJECT to remove the cassette. 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? PAUSE 5 4,5 PLAY RECORD 4 STOP 6 NUMBER 3 1 TV PROG 2 2 PLAY 5 6 5 RECORD 3 4 2 Accidental erasure prevention ●To prevent accidental recording on a recorded cassette, remove its safety tab. To record on it later, cover the hole with adhesive tape. Record safety tab B.E.S.T. takes place at the beginning of both the first SP and the first LP recording after inserting the cassette (Z pg. 18). Recording Resume Function If there is a power outage during recording (or Instant Timer Recording or timer recording), the recording will resume automatically when power is restored to the recorder unless the recorder's memory backup has expired. PAUSE SP/LP STOP/EJECT TV PROG SP/LP

While Watching Another 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? Elapsed Recording Time Indication You can check the exact time of a recording. Tape Remaining Time DISPLAY REMAINING TIME 1 Press DISPLAY (or – –:– –) until the time remaining on the tape appears. ●The display panel shows the tape remaining time with " " displayed. ●By pressing the DISPLAY (or – –:– –) button, you can change the display to show the counter reading, preset position*, clock time or tape remaining time. * Preset position is not displayed during playback. NOTE: Depending on the type of tape used, there may be times when the tape remaining time reading may not appear right away, or is not correct. "– –:– –" may sometimes appear, or the display may blink on occasion. SET COUNTER DISPLAY 1 Press DISPLAY (or – –:– –) until a counter reading appears on the dispay panel. RESET COUNTER 2 Press COUNTER RESET (or 0000) before starting recording or playback. ●The counter is reset to “0:00:00” and shows the exact elapsed time as the tape runs. SELECT PRESET TO WATCH 1 Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you wish to view. ●The programme selected with the TV’s preset controls appears on the TV screen while the one selected with the recorder's TV PROG buttons is recorded on the tape. Instant Timer Recording (ITR) This easy method allows you to record for any length of time from 30 mins. to 6 hours (selectable in 30-min. increments), and shuts off the recorder after recording is finished. START RECORDING 1 Press RECORD on the recorder. ENGAGE ITR MODE 2 Press RECORD again. " " blinks and 0:30 appears on the front display panel. SET RECORDING DURATION 3 If you want to record for more than 30 minutes, press RECORD to extend the time. Each press extends recording time by 30 minutes. NOTE: You can only perform ITR using the RECORD button on the recorder's front panel. RECORD TV PROG TV PROG 0000 – –:– – DISPLAY COUNTER RESET

1 Press PROG. The front display panel looks like this: ENTER PLUSCODE NUMBER 2 Press the NUMBER keys to enter the PlusCode number of the programme you wish to record. ●If you make a mistake, press and input the correct number. The PlusCode number you enter appears on the front display panel: The display panel shows only a 4-digit number. ACCESS VIDEO PLUS+ PROGRAM SCREEN 3 Press OK, and the Video Plus+ Program screen appears (if you’re just starting out, “P1” appears). The display panel shows the programme start time. Pressing changes the display to the programme stop time, then the date and preset position. IMPORTANT Make sure the preset position number you wish to record is displayed; if not, see "Video Plus+ Setup" on page 40 and set the Guide Program number for that PlusCode number correctly. ●If the number you entered is invalid, "ERROR" appears on the screen and "Err" appears on the display panel. Press and input a valid PlusCode number. ●If the "GUIDE PROG SET" screen appears, see "ATTENTION – Regarding Guide Program Number Set" on page 13. Video Plus+ Timer Programming Before performing Video Plus+ Timer Programming: ●Make sure that the recorder's built-in clock is set properly. ●Insert a cassette with the safety tab in place. The recorder will come on automatically. ●Turn on the TV and select the VIDEO channel (or AV mode). With Video Plus+, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise. BASIC OPERATIONS (cont.) 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? OK 4 3,6 PROG 1,6 NUMBER SP/LP 5 2 PDC 7 WEEKLY DAILY STOP+/– VIDEO PLUS+ [0 – 9] = [+/–] : EXPRESS PROGRAMING [PROG] : EXIT VIDEO PLUS+ 12345678 [0 – 9] = [ ] : DELETE [PROG] : EXIT – P1 – VIDEO PLUS+ 123456789 START STOP 21:00 = 22:00 SP VPS/PDC OFF DATE TV PROG 25.12 1 BBC 1 : OK SP

4 Press SP/LP ( ) to set the tape speed. SET PDC MODE 5 Press PDC to select "ON" or "OFF". If "VPS/PDC ON" is displayed on the screen or "VPS/ PDC" is lit on the display panel, PDC is set to ON. If "VPS/PDC OFF" is displayed on the screen or "VPS/ PDC" is not lit on the display panel, PDC is set to OFF. Z "PDC Recording" in the column below. ●VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder. RETURN TO NORMAL SCREEN 6 Press PROG or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. ●Repeat steps 1 – 6 for each additional programme. ENGAGE RECORDER’S TIMER MODE 7 Press ‰ (TIMER). The recorder turns off automatically and ‰ appears on the display panel. ●To disengage the timer, press ‰ (TIMER) again. NOTES: ●To Change The Stop Time . . . . . . press STOP +/– after pressing OK in step 3. You can compensate for anticipated programme schedule delays this way. ●To Timer-Record Weekly Or Daily Serials . . . . . . after pressing OK in step 3, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday – Friday). Either "WEEKLY" or "DAILY" appears on the screen. Pressing the button again makes the corresponding indication disappear. ●You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (Z pg. 16). ●It is not possible to timer-record a TV programme with a PlusCode number which starts with "0". ATTENTION Regarding Guide Program Number Set "GUIDE PROG SET" appears after performing step 3 if the Guide Program number for the PlusCode number you entered has not been set. ●Press the NUMBER keys or %fi to input the preset position number on which your recorder receives that station, then press OK or . The Video Plus+ Program screen appears. (Ex.) To timer-record a BBC2 programme with Video Plus+. * If your recorder receives BBC2 on the preset position 2, press OK or after entering "2". Satellite Receiver Users To timer-record a satellite broadcast using Video Plus+: 1 Perform steps 1 – 7. 2 Set the satellite receiver to the appropriate channel before the selected programme begins. 3 Leave the satellite receiver's power on. Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service only in a very few areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel (Z step 5 above). NOTES: ●PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 IN on your recorder. ●PDC recording is also possible via the AV1 IN/OUT connector. PDC Recording % % Timer Warning – WARNING– TIMER RECORDING TO START SOON [ ] If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on the screen to tell you that the recording is due to start in 5 minutes. NOTES: ●The warning only appears if you’re not in the Timer mode at the time. ●If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder. The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press . GUIDE PROG SET GUIDE PROG TV PROG 2 – – [5∞] = [PROG] : EXIT

If you don’t know the PlusCode number for the programme you wish to record, use the following procedure to set your recorder to timer-record the programme. START+/– 2,3 4 PROG 1,9 ACCESS VIDEO PLUS+ SCREEN 1 Press PROG. ACCESS PROGRAMME SCREEN 2 Press START +/–. (If you’re just starting out, “P1” appears.) The front display panel looks like this: ENTER PROGRAMME START TIME 3 Press START +/– to enter the time you want recording to start. ●Press and hold START +/– to move in 30- minute increments, or press and release repeatedly to move 1 minute at a time. The front display panel looks like this: ENTER PROGRAMME STOP TIME 4 Press STOP +/– to enter the time you want recording to stop. ●Press and hold STOP +/– to move in 30-minute increments, or press and release repeatedly to move 1 minute at a time. ENTER PROGRAMME DATE 5 Press DATE +/– to enter the date on which you wish to record. (The current date first appears on screen. The date you enter will appear in its place.) Before performing Express Timer Programming: ●Make sure that the recorder's built-in clock is set properly. ●Insert a cassette with the safety tab in place. The recorder will come on automatically. ●Turn on the TV and select the VIDEO channel (or AV mode). STOP+/– TV PROG+/– DATE+/– 5 8 PDC 10 SP/LP – P1 – START STOP – –:– – = – –:– – SP VPS/PDC OFF DATE TV PROG – –.– – – – [+/–] = [PROG] : EXIT – P1 – START STOP 21:00 = – –:– – SP VPS/PDC OFF DATE TV PROG – –.– – – – [+/–] = [PROG] : EXIT SP SP

6 Press TV PROG +/– to enter the preset position corresponding to the broadcasting station you wish to record. SET TAPE SPEED 7 Press SP/LP ( ) to set the tape speed. SET PDC MODE 8 Press PDC to select "ON" or "OFF". If "VPS/PDC ON" is displayed on the screen or "VPS/ PDC" is lit on the display panel, PDC is set to ON. If "VPS/PDC OFF" is displayed on the screen or "VPS/ PDC" is not lit on the display panel, PDC is set to OFF. Z "PDC Recording" in the right column. ●VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder. RETURN TO NORMAL SCREEN 9 After confirming all information is correct, press PROG or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. ●Repeat steps 1 – 9 for each additional programme. ENGAGE RECORDER’S TIMER MODE 10 Press ‰ (TIMER). The recorder turns off automatically and ‰ appears on the display panel. ●To disengage the timer, press ‰ (TIMER) again. To Timer-Record Weekly Or Daily Serials . . . . . . anytime during steps 2 through 9, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday – Friday). Either "WEEKLY" or "DAILY" appears on the screen. Pressing the button again makes the corresponding indication disappear. Satellite Receiver Users To timer-record a satellite broadcast using Express Timer Programming: 1 Perform steps 1 – 10. Enter "L-2" for the preset position in step 6. 2 Set the satellite receiver to the appropriate channel before the selected programme begins. 3 Leave the satellite receiver's power on. NOTE: You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (Z pg. 16). Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service only in a very few areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel. (Z step 8 in the left column). NOTES: ●Set the start time (PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording. ●PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 IN on your recorder. ●PDC recording is also possible via the AV1 IN/OUT connector. PDC Recording Timer Warning If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on the screen to tell you that the recording is due to start in 5 minutes. NOTES: ●The warning only appears if you’re not in the Timer mode at the time. ●If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder. The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press . – P1 – START STOP 21:00 = 22:00 SP VPS/PDC OFF DATE TV PROG 25.12 1 BBC 1 [+/–] = [PROG] : EXIT – WARNING– TIMER RECORDING TO START SOON [ ] SP

Check, Cancel And Replace Programmes DISENGAGE TIMER MODE 1 Press ‰, then press . ACCESS PROGRAMME CHECK SCREEN/DISPLAY 2 Press . ACCESS PROGRAMME SCREEN/ DISPLAY 3 Press again to check more information. Each time you press , the next programme's information appears. ●The display panel shows the programme start time. Pressing OK changes the display to the programme stop time, then the date and the preset position. To cancel or replace a programme... CANCEL OR REPLACE A PROGRAMME 4 Press to cancel a programme. To replace a programme, press the appropriate button: START+/–, STOP+/–, DATE+/–, TV PROG+/–, SP/LP ( ), PDC. RETURN TO NORMAL SCREEN/ DISPLAY 5 Press as many times as necessary. If there are still some programmes to be recorded, go on to step 6. RETURN TO TIMER MODE 6 Press ‰. NOTE: You can also check the programmes on the display panel even when the recorder's power is off or the recorder is in the Timer mode. However, it is not possible to cancel or replace the programmes. 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? OK SP/LP PDC START+/– TV PROG+/– DATE+/– STOP+/– – P1 – START STOP 8:00 = 10:00 SP VPS/PDC OFF DATE TV PROG 24.12 3 ITV [ ] : NEXT PR START STOP CH DATE 1 8:00 10:00 3 24.12 2 10:00 10:45 2 25.12 3 11:30 13:00 1 25.12 4 5 6 7 8 [ ] : NEXT SP

index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction. NOTE: Before starting, make sure the recorder is in the Stop mode. ACTIVATE INDEX SEARCH 1 Press or (™ or £). “™ 1” or “£ 1” is displayed on screen and search begins in the corre- sponding direction. ●To access index codes 2 through 9, press or repeatedly until the correct index number is dis- played. Ex.: To locate the beginning of B from the current position, press twice. To locate the beginning of D from the current position, press once. ●When the specified index code is located, playback begins automatically. Current position Index number % fi % fi fi % A B C D E F –2 –1 1 2 3 £ 2 Looking For The Scene You Want SKIP OVER UNWANTED SECTIONS 1 Press 30 SEC 1 to 4 times during playback. Each press initiates a 30-second period of fast-motion playback. Normal playback resumes automatically. NOTE: To return to normal playback during a Skip Search, press PLAY. Skip Search 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? 30 SEC ADVANCED OPERATIONS Instant ReView Simply by pressing a single button, the recorder power comes on, rewinds, and begins playback of the last timer-recorded programme. If you have several programmes recorded, you can easily access any of them. NOTE: Before starting, make sure that the recorder is off and that the Timer mode is disengaged. ACTIVATE INSTANT REVIEW 1 Press REVIEW. The recorder power comes on and the recorder searches for the index code indicating the start of the last timer-recorded programme. Once it’s found, playback begins automatically. ●The front display panel tells you how many programmes have been timer-recorded. If you have, for example, 3 programmes, “REVIEW” and "3" appear and blink. To watch the first of the 3 programmes, press REVIEW three times. The recorder searches and begins playback automatically. You can access a programme as far as 9 index codes away from the current tape position. NOTES: ●Instant ReView is not possible while the recorder is in the Timer mode. ●The number of recorded programmes will not be displayed on the front display panel after Auto Satellite Prog recording (Z pg. 22). REVIEW REVIEW

Playback/ Recording According To Tape Charac- teristics The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. The default setting for both recording and playback is “ON”. B.E.S.T. Picture System TURN ON THE RECORDER 1 Press . ACCESS MAIN MENU SCREEN 2 Press MENU. ACCESS MODE SET SCREEN 3 Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or . SELECT B.E.S.T. MODE 4 Press %fi to move the highlight bar (pointer) to "B.E.S.T.", then press OK or to set to "ON" or "OFF". RETURN TO NORMAL SCREEN 5 Press MENU. % % PLAY 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? PAUSE PLAY OK MENU RECORD PAUSE RECORD Turn on the TV and select the VIDEO channel (or AV mode). MAIN MENU MODE SET AUTO CH SET MANUAL CH SET INITIAL SET [5∞] = [MENU] : EXIT MODE SET AUTO TIMER OFF O. S. D. ON B. E. S. T. ON AUTO SP=LP TIMER OFF [5∞] = [MENU] : EXIT

or press RECORD on the recorder. DURING B.E.S.T. B.E.S.T. COMPLETE ●The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording. NOTES: ●The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording. ●The B.E.S.T. system does not work while Auto Satellite Prog recording is in progress (Z pg. 22). ●In the case of timer recording, the B.E.S.T. system works before recording is initiated. ●Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re- performed. ●Pressing the recorder's RECORD button while "BEST" is displayed does not start Instant Timer Recording (Z pg. 11). ATTENTION Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after RECORD and PLAY on the remote are pressed, or RECORD on the recorder is pressed. To make sure you record the desired scene or programme in its entirety, first perform the following steps: 1) Press and hold PAUSE and press RECORD to engage the RECORD PAUSE mode. ●The recorder then automatically checks the condition of the tape and, after approximately 7 seconds, re- enters RECORD PAUSE. 2) Press PLAY when you are ready to start recording. ●If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF” in step 4 on page 18. Playback The recorder assesses the quality of the tape once you initiate playback. START PLAYBACK 1 Press PLAY. ●The recorder adjusts the playback picture quality based on the quality of the tape in use. ●B.E.S.T. is active during Auto Tracking. “BEST” appears blinking on the recorder’s display panel. NOTES: ●When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well. ●When watching a rental tape or one recorded on another video recorder, or when using this recorder as the player for editing, set B.E.S.T. to your preference by performing steps 1 through 5 on page 18. ●"BEST" only appears at the beginning of automatic tracking. Even though it doesn't appear after that, the B.E.S.T. function is operative.

control. For most tapes this will automatically adjust the tracking to suit the particular tape you are playing. In some circumstances it may be necessary to make manual tracking adjustments. This is usually only associated with old or worn tapes or recordings made on old or worn recorders. If the automatic tracking control fails to operate correctly you will see noise bars across the picture as shown on the left below. To correct this you can override the automatic control and adjust the tracking manually by pressing the TV PROG buttons. OVERRIDE AUTOMATIC TRACKING 1 Press on the remote to engage manual tracking. ADJUST TRACKING MANUALLY 2 Press TV PROG + or – to adjust tracking. RETURN TO AUTOMATIC TRACKING 3 Press on the remote to re-engage automatic tracking. NOTE: When a new tape is inserted, the recorder returns to the automatic tracking mode automatically. Playback Picture Adjustment TV PROG ADVANCED OPERATIONS (cont.)

During Playback Pressing AUDIO on the remote control changes the soundtrack being played back as follows: TRACK On-Screen Display USE HI FI For Hi-Fi stereo tapes L R HI FI For main audio of Bilingual tapes L HI FI For sub audio of Bilingual tapes R NORM For audio-dubbed tapes HI FI For audio-dubbed tapes NORM NOTES: ●"HIFI L R" should normally be selected. In this mode, Hi-Fi stereo tapes are played back in stereo, and the normal audio track is played back automatically for tapes with only normal audio. ●For instructions on recording NICAM stereo and bilingual programmes (See above). ●Bilingual programmes are not currently broadcast in the U.K. ●"O.S.D." must be set to "ON" or the on-screen displays will not appear (Z pg. 26). Receiving NICAM Stereo And Bilingual Programmes Your recorder is equipped with a Digital stereo sound decoder (NICAM), making reception of stereo and bilingual broadcasts possible. When the recorder is tuned to a different station, the type of broadcast being received will be displayed on the TV screen for a few seconds. NOTES: ●The NICAM audio programme will be recorded on the Hi-Fi audio track, and the Standard audio programme on the normal audio track. ●If the quality of stereo sound being received is poor, the broadcast will be received in monaural with better quality. ●Before playing back a programme recorded in stereo, or a bilingual programme, refer to "Soundtrack Selection" (See below). ●"O.S.D." must be set to "ON" or the on-screen displays will not appear (Z pg. 26). ●To listen to a stereo programme, press AUDIO until "HI FI L R" appears on the screen. ●To listen to a bilingual programme, press AUDIO until "HI FI L " or "HI FI R" appears on the screen (as required). ●To listen to the Standard (regular monaural) audio while receiving a NICAM broadcast, press AUDIO until "NORM" appears on the screen. 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? AUDIO Type of Broadcast On-screen Display Being Received Regular Monaural (none) NICAM Stereo ST NICAM NICAM Bilingual BIL NICAM NICAM Monaural NICAM Selecting The Sound You Want

programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder's AV2 IN connector and programme the timer on the satellite receiver; the recorder starts recording when the signals input from the satellite receiver to the AV2 IN connector, and when there is no input signals the recorder stops recording and the power shuts off. Automatic Satellite Programme Recording AV1 IN/OUT AV2 IN R L AUDIO ANT. IN RF OUT OUT DECODER VCR TV EXT.2 EXT.1 NOTES: ●When connecting your recorder to a TV equipped with 21-pin AV input connectors (SCART), follow the illustration above using the cables shown in grey. ●For details, check your satellite receiver’s instruction manual. Mains outlet TV Aerial cable Aerial connector Satellite Receiver Unit Satellite Cable Outdoor Unit Aerial Back of TV 21-pin AV input connectors (SCART) RF OUT ANT. IN Back of Recorder ADVANCED OPERATIONS (cont.)

programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on. ●If you have connected another appliance other than a satellite receiver to the AV2 IN connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on. ●Auto Satellite Prog recording and timer-recording cannot be done at the same time. Before performing the following steps: ●Make sure the satellite receiver is connected to the recorder's AV2 IN connector. (Z pg. 22) ●Programme the timer on the satellite receiver. ●Insert a cassette with the safety tab in place. SET TAPE SPEED 1 Press SP/LP ( ) to set the tape speed. ENGAGE AUTO SATELLITE PROG REC MODE 2 Press and hold REC LINK for about 2 seconds. The button lights up and the recorder turns off automati- cally. ●To disengage the Auto Satellite Prog Rec mode, press REC LINK. The light goes off. ●If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode. NOTES: ●Auto Satellite Prog recording is not possible with the AV1 IN/OUT connector. ●When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON". ●After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function (Z pg. 17). ●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver. ●Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer. ●The REC LINK button blinks while Auto Satellite Prog recording is in progress. ●Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode. ●If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 1 will apply to all the programmes for Auto Satellite Prog recording. ●The B.E.S.T. system (Z pg. 18) does not work while Auto Satellite Prog recording is in progress. ●Just Clock (Z pg. 39) does not work when the Auto Satellite Prog Rec mode is engaged. ●Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme. ●If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the REC LINK button blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording. ●You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 IN connector. REC LINK SP/LP

Edit To Or From Another Video Recorder You can use your video recorder as the source player or as the recording deck. MAKE CONNECTIONS 1 Connect the player’s 21-pin SCART connector to the recorder’s 21-pin SCART connector as illustrated on the below. When Using Your Video Recorder As The Source Player . . . . . . connect its AV1 IN/OUT connector to the recording deck. When Using Your Video Recorder As The Recording Deck . . . . . . . connect its AV2 IN or AV1 IN/OUT connector to the source player. SET RECORDING DECK’S INPUT MODE 2 Set to AUX. With this video recorder, press NUMBER key "0" and/or TV PROG to select “L-1” for the AV1 IN/ OUT connector, or “L-2” for the AV2 IN connector, depending on the connector being used. START SOURCE PLAYER 3 Engage its Play mode. START RECORDING DECK 4 Engage its Record mode. NOTES: ●All necessary cables can be obtained from your dealer. ●When you use this recorder as the player for editing, be sure to set "O.S.D." to "OFF" before starting (Z pg. 26). NUMBER "0" Another recorder RF Cable (provided) Another recorder Recorder 21-pin SCART Cable (not provided) Player Your recorder Recorder Your recorder TV Receiver TV Receiver RF Cable (provided) 21-pin SCART Cable (not provided) Player VIDEO CHAN- NEL or AV mode VIDEO CHAN- NEL or AV mode TV PROG

recorder as the recorder. Edit From A Camcorder MAKE CONNECTIONS 1 Connect the camcorder's AUDIO/VIDEO OUT connectors to the recorder's rear panel AV2 IN or AV1 IN/OUT connector via the optional cable adapter. SET RECORDER’S INPUT MODE 2 Press the NUMBER key "0" and/or TV PROG to select the appropriate input mode depending on the connec- tor being used; "L-1" for the AV1 IN/OUT connector, or "L-2" for the AV2 IN connector. START CAMCORDER 3 Engage its Play mode. START RECORDER 4 Engage its Record mode. NUMBER "0" Camcorder Recorder Player Audio/Video Cable (not provided) Cable adapter (not provided) VIDEO OUT AUDIO OUT TV PROG NOTE: All necessary cables can be obtained from your dealer.

ADVANCED OPERATIONS (cont.) On-Screen Display NOTES: ●When you use this recorder as the player for editing, be sure to set "O.S.D." to "OFF" before starting. ●During playback, the operation mode indicators may sometimes be disturbed depending on the type of tape being used. You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF. ACCESS MAIN MENU SCREEN 1 Press MENU. ACCESS MODE SET SCREEN 2 Move the highlight bar (pointer) to "MODE SET" by pressing %fi, then press OK or . ENABLE/DISABLE ON-SCREEN DISPLAY 3 The default setting is “ON”, so if you want on- screen displays, leave the setting as it is and go to step 4. If you don’t want the displays to appear, press %fi to move the highlight bar (pointer) to "O.S.D." and press OK or to set “O.S.D.” to “OFF”. RETURN TO NORMAL 4 Press MENU. % % 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? OK MENU Other Functions The superimposed indication on the TV screen tells you what the recorder is doing. 1– Operation mode indicators 2– Tape speed SP/LP/EP (EP is for NTSC playback only) 3– NTSC playback display (Z pg. 28) 4– Tape direction 5– Counter display 6– Tape remaining time indicator (Z pg. 11) 7– Audio mode display (Z pg. 21) 8– Tape position indicator (Z pg. 8) 9– NICAM display (Z pg. 21) 10– Current day/month/year 11– Clock display 12– Preset position number and station name/Aux. indicator (L-1 or L-2) 13– Timer warning display (Z pg. 13, 15) 14– Cassette loaded mark q6 PR.1 BBC 1 ] SP 21 : 00 NTSC=PAL 24. 12. 98 – WARNING– TIMER RECORDING TO START SOON [ ] ST NICAM HI FI –1 : 23 : 45 NORM REMAIN 1 : 00 0 + + + + 1 14 3 12 11 10 9 8 7 13 5 6 4 2 MODE SET AUTO TIMER OFF O. S. D. ON B. E. S. T. ON AUTO SP=LP TIMER OFF [5∞] = [MENU] : EXIT

engaged when the recorder power is turned off and automati- cally disengaged when the recorder is powered back on. ACCESS MAIN MENU SCREEN 1 Press MENU. ACCESS MODE SET SCREEN 2 Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or . SELECT MODE 3 Press OK or to select either "ON" or "OFF". RETURN TO NORMAL SCREEN 4 Press MENU. NOTE: For safety, when Auto timer is set to "OFF", all other recorder functions are disabled while the Timer mode is engaged. To disengage the timer, press ‰ (TIMER). % Auto SP→LP Timer If, when timer-recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode to allow complete recording. For Example . . . Recording a programme of 210 minutes in length onto a 180- minute tape NOTES: ●The Auto SP→LP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly with any tapes longer than E-180 or with some tapes of shorter lengths. ●If you have programmed the recorder to timer-record 2 or more programmes, the second programme and those thereafter may not fit on the tape if you set "AUTO SP→LP TIMER" to "ON". In this case, make sure the mode is not engaged, then set the tape speed manually during timer programming. ●In order to ensure that the recording fits on the tape, this feature may leave a short non-recorded section at the end of the tape. ●There may be some picture noise and sound disturbance at the point on the tape where the recorder switches from SP to LP mode. ●If you perform timer recording with both PDC and the Auto SP→LP Timer activated, and the programme goes beyond its originally scheduled length, there may be times when the programme cannot be recorded in its entirety. Total 210 minutes Approximately 150 minutes Approximately 60 minutes SP mode LP mode % Make sure you set "AUTO SP→LP TIMER" to "ON" at the Mode Set screen before the timer-recording starts. ACCESS MAIN MENU SCREEN 1 Press MENU. ACCESS MODE SET SCREEN 2 Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or . SELECT MODE 3 Press %fi to move the highlight bar (pointer) to "AUTO SP→LP TIMER", then press OK or to select "ON". RETURN TO NORMAL SCREEN 4 Press MENU. % % MODE SET AUTO TIMER OFF O. S. D. ON B. E. S. T. ON AUTO SP=LP TIMER ON [5∞] = [MENU] : EXIT MAIN MENU MODE SET AUTO CH SET MANUAL CH SET INITIAL SET [5∞] = [MENU] : EXIT MODE SET AUTO TIMER OFF O. S. D. ON B. E. S. T. ON AUTO SP=LP TIMER OFF [5∞] = [MENU] : EXIT

50 times repeatedly. START PLAYBACK 1 Press PLAY. ACTIVATE REPEAT PLAYBACK 2 Press PLAY and hold for over 5 seconds, then release. ●The Play indicator ( ) on the display panel blinks slowly. ●The tape plays 50 times automatically, and then stops. STOP PLAYBACK 3 Press STOP at any time to stop playback. NOTE: Pressing PLAY, REW, FF or PAUSE also stops Repeat Playback. NTSC Playback Your video recorder is equipped with NTSC circuitry that can play back NTSC tapes. LOAD A CASSETTE 1 Insert a cassette recorded in NTSC. START PLAYBACK 2 Press PLAY. ●"NTSC→PAL" appears on the screen for about 5 seconds. ●Some TVs shrink the picture vertically and place black bars at the top and bottom of the screen. This is not a malfunction on the part of either the video recorder or the TV. ●The picture may roll up and down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.) ●The counter and tape remaining time readings will be incorrect. ●During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour. ●Depending on the type of TV, the top and bottom portions of superimposed displays may be cut off during NTSC playback. Next Function Memory You can set your recorder's power to go off automatically after the tape is fully rewound. Before starting, make sure the recorder is in the Stop mode. For Automatic Power Off After Tape Rewind . . . . . . press REW, then press within 2 seconds. ADVANCED OPERATIONS (cont.) 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? FF REW STOP PAUSE PLAY

your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo. SYSTEM CONNECTIONS MAKE CONNECTIONS 1 Connect the AUDIO OUT L and R connectors on your video recorder to the AUX IN or TAPE MONITOR terminals on your stereo system's receiver or amplifier. NOTES: ●When connecting your recorder's audio output connectors to a stereo amplifier, make sure you connect L and R correctly. ●If NICAM TV broadcasts are receivable in your area, this recorder can record them independently of the TV set and play them back through the connected stereo system. ●When listening to sound through the connected stereo system, turn the TV's volume down completely. CAUTIONS: ●This recorder has a dynamic range of more than 80 dB with regards to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them. ●Some speakers and televisions are specially shielded to prevent television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the video playback picture. AUX IN or TAPE MONITOR Television Back of Recorder Speaker Speaker CD Player FM Tuner Stereo Amplifier Audio Cable (not provided) Mains outlet AUDIO OUT

which your TV receives picture and sound signals from the video recorder through the RF cable. With AV Connection ACCESS VIDEO CHANNEL SET MODE 1 Press and hold down STOP on the recorder until the display panel shows the following. SET VIDEO CHANNEL 2 Press TV PROG – until the display panel shows "–OUT– –". ●Now the video channel is set to off. EXIT VIDEO CHANNEL SET MODE 3 Press OK. To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this. ●If you have connected the video recorder to your TV via both an RF cable and a 21-pin SCART cable (AV connection), you do not need the video channel so you have to set the video channel to off. — Go to "With AV Connection" below. ●If you have connected the video recorder to your TV via an RF cable only (RF connection), you have to set the correct video channel — Go to "With RF Connection" on page 31. Before performing the following procedure, make sure that: n the mains power cord is plugged into the mains outlet. n the video recorder is turned off and there is no cassette inserted in the recorder. n batteries have been installed in the remote control. 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? TV PROG OK IMPORTANT Perform the following steps only if — — Video Channel Set has not been done correctly by the Auto Set Up function (Z pg. 6). — interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area. — you change the connection between your recorder and TV from RF connection to AV connection, or vice versa. STOP

sure that: n the mains power cord is plugged into the mains outlet. n the video recorder is turned off and there is no cassette inserted in the recorder. n the connected TV is turned on. n batteries have been installed in the remote control. ACCESS VIDEO CHANNEL SET MODE 1 Press and hold down STOP on the recorder until the display panel shows the following. SET VIDEO CHANNEL 2 Press TV PROG+ or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area. Refer to list on page 38 for details of broadcast stations in your area. Then set your TV to UHF channel 36. (Refer to the instructions supplied with your TV set for how to do this.) ●If the two vertical white bars appear clearly on the screen as shown in the illustration at buttom left, go to step 3. ●If the two vertical white bars do not appear clearly, re- set the video recorder to another vacant channel and try again. IMPORTANT ●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels. ●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer. EXIT VIDEO CHANNEL SET MODE 3 Press OK. (Ex.) If channel 36 is available in your area TEST SIGNAL The channel on which the screen on the left appears clearly in step 2 is your Video Channel. To view picture signals from the video recorder, set your TV to the Video Channel. With RF Connection 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? TV PROG OK STOP

Tuner Set IMPORTANT Perform the following steps only if — — Auto Channel Set has not been set correctly by Auto Set Up function (Z pg. 6). — you have moved to a different area or if a new station starts broadcasting in your area. Turn on the TV and select the VIDEO channel (or AV mode). Your recorder needs to memorise all necessary stations in preset positions in order to record TV programmes. Auto Channel Set automatically assigns all receivable stations in your area to call them up by using the TV PROG buttons without going through any vacant channel. TURN ON THE RECORDER 1 Press . ACCESS MAIN MENU SCREEN 2 Press MENU. PERFORM AUTO CHANNEL SET 3 Move the highlight bar (pointer) to "AUTO CH SET" by pressing %fi, then press OK or . ●The Auto Set screen appears, and remains on screen while the recorder searches for receivable stations. As Auto Channel Set progresses, the " " mark on the screen moves from left to right. Wait until the screen as shown in step 4 appears. ●Auto Channel Set usually takes about 4 – 12 minutes; the duration varies by area. 0 + + + End Beginning % Auto Channel Set TV PROG OK MENU MAIN MENU MODE SET AUTO CH SET MANUAL CH SET INITIAL SET [5∞] = [MENU] : EXIT AUTO SET PLEASE WAIT [MENU] : EXIT

is displayed on the screen for about 5 seconds, a Confirmation screen looking like the one on the right appears. The stations your recorder located appear on a Confirmation screen — preset positions (PR), channels (CH) and station names (ID – Z pg. 37). The blueback screen and the programme currently being broadcast by the station which is blinking appear alternately for 8 seconds each. To view the next page, use the %fi button on the remote control. ●The Guide Program numbers will also be set automatically during Auto channel Set. RETURN TO NORMAL SCREEN 5 Press MENU. ●Using the Confirmation screen, you can skip or add preset positions, enter station names and perform other operations. Refer to pages 34 – 38 for the procedures. ●Depending on reception conditions, the stations may, on occasion, not be stored in order, and the station names may not be stored correctly. IMPORTANT ● In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly, when you timer-record a TV programme using Video Plus+, the recorder will record a TV programme of a different station. When programming the timer using Video Plus+, be sure to check that the preset position correspond- ing to the broadcasting station you wish to record has been selected (Z pg. 12, "Video Plus+ Timer Programming"). ● Your video recorder memorizes all detected stations even if reception of some of them is poor. In these cases picture quality may be poor. To delete those stations which have an unacceptable picture Z "Delete A Channel" on page 35. NOTES: ●Fine tuning is performed automatically during Auto Channel Set. If you wish to perform it manually, refer to page 35. ●If, for any reason, you perform Auto Channel Set when the aerial cable is not connected properly, "SCAN COMPLETED - NO SIGNAL-" appears on the screen in step 4. When this happens, make sure of the aerial connection and press OK; Auto Channel Set will take place again. 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? MENU % % PR CH ID PR CH ID 01 26 BBC1 08 –––– 02 33 BBC2 09 –––– 03 23 ITV 10 –––– 04 30 CH4 11 –––– 05 37 CH5 12 –––– 06 –––– 13 –––– 07 –––– 14 –––– [5∞ ] = : EDIT = [X] : DELETE [MENU] : EXIT 5 5 5 OK

Storing Channels Manually To store channels that were not stored during Auto Set Up (Z pg. 6) or Auto Channel Set (Z pg. 32). ACCESS MAIN MENU 1 Press MENU. ACCESS CONFIRMATION SCREEN 2 Press %fi to move the highlight bar (pointer) to “MANUAL CH SET”, then press OK or . The Confir- mation screen appears. SELECT POSITION 3 Press %fi until an open position in which you want to store a channel begins blinking, then press OK. The Manual Channel Set screen appears. INPUT CHANNEL 4 Press the NUMBER keys to input the channel number you want to store. ●To input the registered station name (ID – Z pg. 37), press until "– – –␣–" (ID setting) begins blinking, then press %fi. ●For fine tuning adjustment, press until "+/–" begins blinking, then press %fi. While tuning, “+” or “–” appears. ENTER NEW CHANNEL INFORMATION 5 Press OK and the Confirmation screen appears. ●Repeat steps 3 through 5 as necessary. CLOSE CONFIRMATION SCREEN 6 Press MENU. ●To change positions, see "Change Station Preset Position" (Z pg. 35). ●If you wish to set station names other than the ones registered in your recorder, Z "Set Stations (B)" on page 36. % ATTENTION After you have stored channels manually, be sure to perform Guide Program Number Set (Z pg. 40) in order to get proper results from Video Plus+ timer recording. % % 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? NUMBER (Ex.) To store in position 6. The blueback screen and the programme currently being broadcast by the selected channel appear alternately for 8 seconds each. The blueback screen and the programme currently being broadcast by the selected channel appear alternately for 8 seconds each. % % 5 5 PR CH ID PR CH ID 01 26 BBC1 08 –––– 02 33 BBC2 09 –––– 03 23 ITV 10 –––– 04 30 CH4 11 –––– 05 37 CH5 12 –––– 06 –––– 13 –––– 07 –––– 14 –––– [5∞ ] = : EDIT = [X] : DELETE [MENU] : EXIT PR CH ID FINE 06 CH21 –––– +/– [0–9] : SELECT [ ] : CURSOR += : OK [MENU] : EXIT ∞ ∞ MENU OK

page 34 to access the Confirmation screen before continuing. Change Station Preset Position SELECT ITEM 1 Press %fi until the item you want to move begins blinking. Then press OK and the station name (ID) and its channel (CH) number begin blinking. SELECT NEW POSITION 2 Press %fi to move the station to the new preset position, then press OK. Example: If you moved the station in position 4 to position 2, the stations originally in positions 2 and 3 each move down one space. ●Repeat steps 1 and 2 as necessary. CLOSE CONFIRMATION SCREEN 3 Press MENU. SELECT ITEM 1 Press %fi until the item you want to delete begins blinking. DELETE CHANNEL 2 Press . ●The item directly beneath the cancelled one moves up one line. ●Repeat steps 1 and 2 as necessary. CLOSE CONFIRMATION SCREEN 3 Press MENU. Delete A Channel ATTENTION After you have deleted channels or changed preset positions, be sure to perform Guide Program Number Set (Z pg. 40) in order to get proper results from Video Plus+ timer recording. Perform steps 1 and 2 of "Storing Channels Manually" on page 34 to access the Confirmation screen before continuing. Perform steps 1 and 2 of "Storing Channels Manually" on page 34 to access the Confirmation screen before continuing. SELECT CHANNEL TO FINE-TUNE 1 Press %fi until the channel you want to tune begins blinking. ACCESS MANUAL CHANNEL SET SCREEN 2 Press OK twice. The Manual Channel Set screen appears. PERFORM TUNING 3 Press until "+/–" begins blinking, then press %fi until the picture is clearest. Then press OK. ●The Confirmation screen appears. ●Repeat steps 1 through 3 as necessary. CLOSE CONFIRMATION SCREEN 4 Press MENU. Fine-Tuning Channels Already Stored % % % % % % % PR CH ID PR CH ID 01 26 BBC1 08 –––– 02 23 ITV 09 –––– 03 30 CH4 10 –––– 04 33 BBC2 11 –––– 05 37 CH5 12 –––– 06 –––– 13 –––– 07 –––– 14 –––– [5∞ ] : MOVE : MANUAL CH SET [MENU] : EXIT PR CH ID PR CH ID 01 26 BBC1 08 –––– 02 33 BBC2 09 –––– 03 23 ITV 10 –––– 04 30 CH4 11 –––– 05 37 CH5 12 –––– 06 –––– 13 –––– 07 –––– 14 –––– [5∞ ] : MOVE = [MENU] : EXIT % % 5 5 5 5

% SELECT STATION NAME CHARACTER 1 Press until the first letter of the station name begins blinking. ENTER NEW CHARACTER 2 Press %fi to cycle through the characters (A–Z, 0–9, –, *, +, (space) ) and stop when the desired character is indicated, then press to enter. Enter the remaining characters the same way (maximum of 4). After entering all characters, press OK. ●The Confirmation screen appears. ●If you make a mistake, press until the incorrect character begins blinking. Then enter the correct character by pressing %fi. CLOSE CONFIRMATION SCREEN 3 Press MENU. [ % % Set Stations (B) Perform steps 1 and 2 of "Storing Channels Manually" on page 34 to access the Confirmation screen before continuing. SELECT ITEM 1 Press %fi until the item you want begins blinking. ACCESS MANUAL CHANNEL SET SCREEN 2 Press OK twice. SELECT NEW STATION 3 Press until the station name (ID) begins blinking, then press %fi until the new station’s name (ID) you want to store begins blinking. Registered station names (Z pg. 37) appear as you press %fi. SWITCH STATIONS 4 Press OK. ●The Confirmation screen appears. ●Repeat steps 1 through 4 as necessary. CLOSE CONFIRMATION SCREEN 5 Press MENU. Set Stations (A) Set station names that are registered in your recorder. % Perform steps 1 and 2 of "Storing Channels Manually" on page 34 to access the Confirmation screen and then perform step 1 and 2 of "Set Stations (A)" on the left before continuing. Set station names other than the ones registered in your recorder. % % PR CH ID FINE 06 CH45 –––– +/– [5∞] : CHANGE ID [ ] : CURSOR += : OK [MENU] : EXIT ∞ ∞ PR CH ID FINE 06 CH45 BBC1 +/– [5∞] : A-Z, 0-9 [ ] : CURSOR += : OK [MENU] : EXIT ∞ ∞

STATION NAME ID* Anglia TV ANGL ARD ARD ARTE ARTE BBC Group BBC BBC1 BBC1 BBC2 BBC2 Berlin 1 BLN1 Berlin 2 BLN2 Border TV BORD Bayern1 BR1 Bayern3 BR3 BRT1 BRT1 BRT2 BRT2 Children Ch CHLD Canal + CH+ CNN CNN Channel TV CHNL Central TV CNTR Channel 4 CH 4 Channel 5 CH 5 DRS DRS DR TV DRTV DSF DSF Euronews EURN Euronews EURO Eurosports EURS France1 FR1 France2 FR2 France3 FR3 Granada TV GRNA Grampian TV GRMP Hessen1 HR1 Hessen3 HR3 HRT HRT HTV HTV ITV Network ITV Kabelkanal KABL London LNDN MDR MDR MTV MTV Nord3 N3 NDR1 NDR1 NDR3 NDR3 NED1 NED1 NED2 NED2 NED3 NED3 Network 2 NET2 NRK NRK N-TV N-TV Offener Kanal OKAN ORF1 ORF1 ORF2 ORF2 ORF3 ORF3 OWL 3 OWL3 Premiere PRMI PR07 PR07 RAI1 RAI1 RAI2 RAI2 RAI3 RAI3 RB1 RB1 RB3 RB3 Rikisutvarpid-S RKPS RTBF 1 RTB1 RTBF 2 RTB2 RTE 1 RTE1 RTL RTL RTL 2 RTL2 RTP RTP STATION NAME ID* SAT SAT SAT 1 SAT1 Scottish TV SCOT SC4 SC4 SDR SDR SDR1 SDR1 SFB1 SFB1 SFB3 SFB3 SKY SKY Sky One SKY1 Sky Net SKYN Sport SPRT SR 1 SR1 Super RTL SRTL STV Test STVT STV 1 STV1 STV 2 STV2 Suedwest3 SW3 SWF 1 SWF1 Schweiz4 SWZ4 TYNE TEES TEES Text TEXT TF1 TF1 TNT int TNT TRT int TRT TSI TSI TSR TSR TSW TSW TVE TVE TV Polonia TVPA TVP 1 TVP1 TVP 2 TVP2 TVS TVS TV2 TV2 TV5 TV5 Tele Zurich TZUR Ulster TV ULST Veronica VERN VIVA VIVA VIVA2 VIV2 VOX VOX VTM VTM VT4 VT4 West1 WDR1 West3 WDR3 YLE 1 YLE1 YLE 2 YLE2 Yorkshire TV YORK ZDF ZDF Zurich 1 ZUR1 3SAT 3SAT * The "ID" abbreviation is what is shown on-screen in lieu of the station name. The "ID" abbreviation is listed in the Confirma- tion screen and is displayed on the TV screen each time the recorder is tuned to a different station.

TV Station Channel Number Guide Only the main stations are listed. There are in addition many relay stations, and full lists are available from the BBC and ITV. BBC1 BBC2 ITV CH4 CH5 London & South-East Bluebell Hill ......................... 40 46 43 65 — Crystal Palace....................... 26 33 23 30 37 Dover ................................... 50 56 66 53 — Heathfield ............................ 49 52 64 67 — Oxford ................................. 57 63 60 53 49 South-West Beacon Hill .......................... 57 63 60 53 — Caradon Hill ........................ 22 28 25 32 — Huntshaw Cross ................... 55 62 59 65 67 Redruth ................................ 51 44 41 47 37 Stockland Hill ...................... 33 26 23 29 — Channel Islands Fremont Point....................... 51 44 41 47 — South Hannington .......................... 39 45 42 66 35 Midhurst ............................... 61 55 58 68 — Rowridge.............................. 31 24 27 21 — West Mendip ................................ 58 64 61 54 37 East Sandy Heath......................... 31 27 24 21 39 Sudbury................................ 51 44 41 47 35 Tacolneston .......................... 62 55 59 65 52 Midlands Ridge Hill ............................. 22 28 25 32 35 Sutton Coldfield ................... 46 40 43 50 37 The Wrekin .......................... 26 33 23 29 35 Waltham .............................. 58 64 61 54 35 North Belmont ............................... 22 28 25 32 56 Emley Moor.......................... 44 51 47 41 37 BBC1 BBC2 ITV CH4 CH5 North-West Caldbeck .............................. 30 34 28 32 56 Winter Hill ........................... 55 62 59 65 48 North-East Bilsdale West Moor .............. 33 26 29 23 35 Chatton ................................ 39 45 49 42 — Pontop Pike .......................... 58 64 61 54 68 Scotland Angus ................................... 57 63 60 53 — Black Hill ............................. 40 46 43 50 37 Sandale ................................ 22 — — — — Caldbeck .............................. — 34 28 32 56 Creigkelly ............................. 31 27 24 21 48 Darvel .................................. 33 26 23 29 35 Durris ................................... 22 28 25 32 67 Eitshal .................................. 33 26 23 29 — Keelylang Hill ...................... 40 46 43 50 — Knock More ......................... 33 26 23 29 — Rosemarkie .......................... 39 45 49 42 67 Rumster Forest...................... 31 27 24 21 — Selkirk .................................. 55 62 59 65 52 Wales Blaenplwyf ........................... 31 27 24 21 56 Carmel ................................. 57 63 60 53 — Llanddona ............................ 57 63 60 53 — Moel-y-Parc ......................... 52 45 49 42 — Presely ................................. 46 40 43 50 37 Wenvoe................................ 44 51 41 47 — Northern Ireland Brougher Mountain .............. 22 28 25 32 — Divis .................................... 31 27 24 21 37 Limavady ............................. 55 62 59 65 — For customers in the U.K.

through automatic adjustments at regular intervals, by reading data from a PDC signal. The Just Clock option can be set "ON" or "OFF" at the Clock Set screen (the default setting is "ON"). Press OK until the Just Clock setting begins blinking, then press %fi to change the setting. IMPORTANT: If you turn the Just Clock function off, the accuracy of your recorder’s built-in clock may be impaired, which could adversely affect timer recording. TURN THE RECORDER ON 1 Press . ACCESS MAIN MENU SCREEN 2 Press MENU. ACCESS INITIAL SET SCREEN 3 Move the highlight bar (pointer) to "INITIAL SET" by pressing %fi, then press OK or . ACCESS CLOCK SET SCREEN 4 Move the highlight bar (pointer) to "CLOCK SET" by pressing %fi, then press OK or . The Clock Set screen appears. SET DATE AND TIME 5 Press %fi to set the time, then press OK or . The "date" display begins blinking. Repeat the same procedure to set the date and year. ●When you set the time, press and hold %fi to change the time by 30 minutes. ●When you set the date, press and hold %fi to change the date by 15 days. SET JUST CLOCK 6 The default setting is “ON”. Set as desired by pressing %fi, then press OK or . ●For the Just clock function, Z "Just Clock" on the left. ●If you set to “OFF”, you can disregard the next step as you won’t be able to receive regular clock adjustments. SET CLOCK DATA SOURCE PRESET 7 The recorder is preset to receive clock setting and adjustment data from preset position 1. Press %fi to set the preset position to the number representing the station transmitting clock setting data (BBC1, BBC2, etc.), then press OK or . START CLOCK OPERATION 8 Press MENU. Clock Set Turn on the TV and select the VIDEO channel (or AV mode). % NOTES: ●Just Clock (when set to "ON") adjusts the recorder's built-in clock every hour, except for 23:00, 0:00, 1:00 and 2:00. ●Just Clock is not effective when . . . – the recorder’s power is on. – the recorder is in the Timer mode. – a difference of more than 3 minutes exists between the built-in clock’s time and the actual time. – the recorder is in the Auto Satellite Prog Rec mode (Z pg. 22). ●If Just Clock is set to "ON", the recorder’s clock is automati- cally adjusted at the start/end of Summer Time. ●Just Clock may not function properly in poor reception conditions. IMPORTANT If you performed Auto Set Up (Z pg. 6) or Auto Channel Set (Z pg. 32), without ever having set the clock previ- ously, the recorder's built-in clock is also set automatically. Perform the following steps only if — — Auto Clock Set has not been performed correctly by Auto Set Up or Auto Channel Set. or — the recorder's memory backup has expired. or — you want to change Just Clock setting (Z "Just Clock" in the left column). % % % 1 2 3 4 5 6 7 8 9 0 2 4 1 3 ? OK MENU % INITIAL SET CLOCK SET GUIDE PROG SET [5∞] = [MENU] : EXIT CLOCK SET TIME DATE YEAR 0: 00 01 . 01 98 JUST CLOCK: ON TV PR. : 1 [5∞] = [MENU] : EXIT

SUBSIDIARY SETTINGS (cont.) IMPORTANT Normally, Auto Set Up (Z pg. 6) or Auto Channel Set (Z pg. 32) sets the Guide Program Numbers automatically. You need to set the Guide Program Numbers manually only in the following cases. ●When timer-programming with Video Plus+, the preset position, where the station you wish to record is received on your recorder, is not selected. — Set the Guide Program Number for that station manually. ●When you add/delete a channel or change preset positions manually after Auto Set Up or Auto Channel Set has taken place. — Set the Guide Program Numbers for all the receivable stations manually. ●When you wish to timer-record a satellite programme with Video Plus+. — Set the Guide Program Numbers for all satellite broadcasts received on your satellite receiver. Turn on the TV and select the VIDEO channel (or AV mode). Guide Program Number Set ACCESS MAIN MENU SCREEN 1 Press MENU. ACCESS INITIAL SET SCREEN 2 Press %fi to move the highlight bar (pointer) to "INITIAL SET", then press OK or . ACCESS GUIDE PROG SET SCREEN 3 Press %fi to move the highlight bar (pointer) to "GUIDE PROG SET", then press OK or . ENTER GUIDE PROG NUMBER 4 Press %fi or NUMBER keys to enter the Guide Program number for the desired station as shown in the TV listings. Then press OK or . % (Ex.) When inputting the Guide Program number 4 for CH4. % ENTER RECEIVING PRESET POSITION NUMBER 5 Press %fi or NUMBER keys to input the number of the recorder's preset position on which the Guide Program number's broadcast is received. Then press OK or . ●If the satellite broadcast is received on your recorder's auxiliary channel "L-2", select "L-2" for the preset position. • Repeat steps 4 and 5 as necessary. RETURN TO NORMAL SCREEN 6 Press MENU. (Ex.) If CH4 is received on preset position 4. Guide Program Number "Guide Program (GUIDE PROG) number" refers to the assigned TV station numbers, according to broadcast area, for Video Plus+ timer recording. The Guide Program numbers can be found in most TV listings. % % GUIDE PROG SET GUIDE PROG TV PROG 4 5 [5∞] = [MENU] : EXIT GUIDE PROG SET GUIDE PROG TV PROG 4 4 CH4 [5∞] = [MENU] : EXIT

during playback or search? ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ A. The tape is automatically rewound to the beginning. Q. Can the video recorder indefinitely remain in the still mode? A. No. It stops automatically after 5 minutes to protect ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ the heads. Q. During search, slow, still and frame-by-frame playback, I can’t hear any audio. What’s the problem? ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ A. This is normal. Q. When returning from multi-speed search to normal playback, the picture is disturbed. Should I be concerned about this? ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ A. No, it is normal. Q. Noise bars appear during multi-speed search. What’s the problem? ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ A. This is normal. Q. Other than preventing further recording, what effect does removing the Record Safety tab have? ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ A. It disables marking of index codes. Q. Sometimes, during Index Search, the video recorder can’t find the programme I want to see. Why not? ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ A. There may be index codes too close together. ATTENTION This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual. RECORDING Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen? A. This is normal. It reduces distortion at the pause and ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ resume points. Q. Can the video recorder indefinitely remain in the Record-Pause mode? A. No. The video recorder shuts off automatically after 5 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ minutes to protect the heads. Q. What happens if the tape runs out during recording? A. The video recorder automatically rewinds it to the beginning or, if Timer Recording, the cassette is ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ejected. TIMER RECORDING Q. " " and "‰" remain lit on the display panel. Is there a problem? A. No. This is a normal condition for a timer recording in ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ progress. Q. Can I programme the timer while I’m watching a tape or a TV broadcast? A. You won’t see the picture as it is replaced by the on- screen menu, but the audio from the program or tape ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ you’re viewing can be heard. Q. Is it possible to timer-record a TV programme broadcast in 2000? ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ A. Yes, it is possible. Questions And Answers SUBSIDIARY INFORMATION

Before requesting service for a problem, use this chart to see if you can correct the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair. POSSIBLE CAUSE ●The mains power cord is disconnected. ●“‰“ is displayed on the display panel with Auto Timer set to "OFF". ●The batteries are discharged. SYMPTOM 1. No power is applied to the recorder. 2. The clock is functioning properly, but the recorder cannot be powered. 3. The remote control won’t function. CORRECTIVE ACTION Connect the mains power cord. Press the ‰ button to turn the “‰“ indicator off. Replace the dead batteries with new ones. SYMPTOM 1. The tape does not run during recording. 2. The tape will not rewind or fast- forward. CORRECTIVE ACTION Press PLAY to turn the “^“ indicator off. Check the cassette. SYMPTOM 1. The playback picture does not appear while the tape is running. 2. Noise appears during visual search. 3. Noise appears during normal playback. 4. The playback picture is blurred or interrupted while TV broadcasts are clear. 5. Breaks are noticeable in Hi-Fi soundtrack. POSSIBLE CAUSE ●If you’re using the RF OUT connec- tion . . . . . . the TV receiver’s channel selector is not set to the VIDEO channel. . . . the recorder's VIDEO channel has not been correctly set. ●If you’re using the AV connection, the TV receiver is not set to the AV mode. ●This is normal. ●The automatic tracking mode is engaged. ●The video heads may be dirty. ●Automatic tracking is engaged. CORRECTIVE ACTION If you are using the RF OUT connec- tion . . . . . . set the TV receiver to the VIDEO channel. (Z pg. 6) . . . Perform "Video Channel Set" (Z pg. 30) If you are using the AV connection, set the TV to its AV mode. Try manual tracking (Z pg. 20). Consult your JVC dealer. Engage and adjust tracking manually. (Z pg. 20) POSSIBLE CAUSE ●“^“ is displayed on the display panel. ●The tape is already fully rewound or fast-forwarded. CORRECTIVE ACTION Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed. Set to the desired preset. Confirm that the source is properly connected. Confirm that all units’ power switches are turned on. Set the input mode to “L-1” or “L-2”. POSSIBLE CAUSE ●There is no cassette loaded, or the cassette loaded has had its Record Safety tab removed. ●“L-1” or “L-2” has been selected as the input mode. ●The source (another video recorder, camcorder) has not been properly connected. ●All necessary power switches have not been turned on. ●The input mode is not correct. SYMPTOM 1. Recording cannot be started. 2. TV broadcasts cannot be recorded. 3. Tape-to-tape editing is not possible. Troubleshooting POWER TAPE TRANSPORT PLAYBACK RECORDING

settings. Press ‰ and confirm that “‰“ is displayed on the display panel. Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes. Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape. Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the Record Safety tab intact. Check the programmed data and re- programme as necessary, then press ‰ again. The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme. Refer to "Guide Program Number Set" and re-perform the procedure (Z pg. 40). SYMPTOM 1. Timer recording won’t work. 2. Timer programming is not possible. 3. “‰“ and “]“ on the display panel won’t stop blinking. 4. The cassette is automatically ejected, and “‰“ and “]“ on the display panel won’t stop blinking. 5. “‰“ blinks for 10 seconds and the Timer mode is disengaged. 6. The cassette is automatically ejected, the power shuts off and “‰“ and “]“ won’t stop blinking. 7. Video Plus+ does not timer-record properly. POSSIBLE CAUSE ●The clock and/or the timer have been set incorrectly. ●The timer is not engaged. ●Timer recording is in progress. ●The timer is engaged but there’s no cassette loaded. ●The loaded cassette has had its Record Safety tab removed. ●‰ has been pressed when there are no programs in memory, or the timer record information has been programmed incorrectly. ●The end of the tape was reached during timer recording. ●The recorder’s preset positions have been set incorrectly. CORRECTIVE ACTION Position the camcorder so its microphone is away from the TV. Turn the TV’s volume down. If you need the skipped channels, restore them (Z pg. 34). Press PAUSE to pause the recording, change presets, then press PLAY to resume recording. Perform manual setting again. Connect the TV aerial cable to the recorder properly and turn off the recorder power once, then turn the recorder power back on again. The recorder will try Auto Set Up again (Z pg. 6). SYMPTOM 1. Whistling or howling is heard from the TV during camcorder record- ing. 2. When scanning channels, some of them are skipped over. 3. The preset cannot be changed. 4. Channel settings that were made manually seem to have changed or disappeared. 5. No channels are stored in the recorder's memory. POSSIBLE CAUSE ●The camcorder’s microphone is too close to the TV. ●The TV’s volume is too high. ●Those channels have been desig- nated to be skipped. ●Recording is in progress. ●After the manual settings were made, Auto Channel Set was performed. ●The TV aerial cable was not connected to the recorder when Auto Set Up was performed. 4. Camcorder recording is not possible. ●The camcorder has not been properly connected. ●The input mode is not correct. Confirm that the camcorder is properly connected. Set the input mode to “L-1” or “L-2”. OTHER PROBLEMS TIMER RECORDING

DISPLAY REC LINK COUNTER RESET TV PROG TV PROG TIMER STANDBY/ON SP/LP PUSH JOG 1 2 3 # & ^ % $ ! 8 0 9 4 5 6 7 * @ 1 STANDBY/ON Button turns recorder on/off (loading a cassette also turns power on). 2 TIMER Button engages timer standby mode. Z pg. 13, 15 3 SP/LP Button selects tape speed. Z pg. 10 4 Cassette Loading Slot is where cassette is inserted; door closes, "cassette loaded" indicator lights up on front display panel. 5 REVIEW Button "reviews" timer-recorded programme. Z pg. 17 6 PLAY Button plays back tape Z pg. 8; cancels Pause, Still, Slow, Search modes. Z pg. 9 7 PUSH JOG ™£ Button initiates functions such as Index Search Z pg. 17, variable-speed search, frame by frame playback. Z pg. 9 8 TV PROG +/– Buttons select a preset position. Z pg. 10 9 REC LINK Button enables/disables the Auto Satellite Prog Rec mode. Z pg. 23 0 COUNTER RESET Button resets counter to 0:00:00. Z pg. 11 ! Display Panel provides clear view of various displays and indicators. Z pg. 45 @ Infrared Beam Receiving Window is where remote control should be aimed when in use. # RECORD Button starts regular recording (press once), Instant Timer Recording (press twice); sets duration of ITR. Z pg. 10, 11 $ PAUSE Button stops tape temporarily during recording Z pg. 10; stops tape temporarily during playback; plays back frame by frame with each additional press. Z pg. 9 % Rewind [REW] Button rewinds the tape Z pg. 8; initiates high-speed reverse search. Z pg. 9 ^ Fast Forward [FF] Button fast-forwards tape Z pg. 8; initiates high-speed forward search. Z pg. 9 & DISPLAY Button switches display between clock time, tape remaining time, counter readings, preset position*. Z pg. 11 * Preset position is not displayed during playback. * STOP/EJECT Button stops tape; ejects tape during Stop mode. Z pg. 8 Index

5 AV2 IN Connector enables connection of satellite receiver or second recorder; input recordable when "L-2" selected. Z pg. 22, 24 6 RF OUT Connector enables connection to aerial terminal of TV receiver. Z pg. 5 1 Mains Power Cord supplies power to recorder. Z pg. 5 2 AV1 IN/OUT Connector enables AV connection to TV or second recorder; input recordable when "L-1" selected. Z pg. 5, 24 3 AUDIO OUT (L/R) Connectors enable connection of audio cassette recorder, TV or second video recorder for dubbing. Z pg. 29 REAR VIEW DISPLAY PANEL 1 B.E.S.T. Picture System Display lights from bottom to top while B.E.S.T. is active. Z pg. 18 2 Symbolic Mode Indicators 3 Tape Speed Indicators display mode of recording; light during Record or Play mode. Z pg. 10 * EP is only for NTSC playback. 4 Programme Time Indicators show the programme start time ( ) and the programme stop time ( ) for timer-recording. Z pg. 14 5 "Timer" Indicator lights when ‰ has been pressed to engage Timer mode. Z pg. 13, 15 6 Tape Remaining Time Indicator displays time remaining on tape when certain buttons are pressed. Z pg. 11 7 Channel Display shows preset position where the station currently being received is stored. Clock Display shows current time. Z pg. 7 8 Instant REVIEW Indicator blinks after timer-recording and shows how many programmes have been timer- recorded. Z pg. 17 0 "Cassette Loaded" Mark lights once a cassette is inserted; remains lit until cassette ejected or power turned off. 9 PDC Indicator lights when PDC has been engaged for timer recording. Z pg. 13, 15 * VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder. ! Counter shows time elapsed since playback or recording began. With displayed, shows time remaining from current tape position to end of tape (Z pg. 11). Counter, Preset Position*, Clock and Tape Remaining Time Display appear alternately when DISPLAY (or – –:– –) is pressed. * Preset Position is not displayed during playback. @ Mode shows external input mode selected (L-1 or L-2). STILL: SLOW: RECORD: RECORD PAUSE: PLAY: FF/REW VARIABLE SHUTTLE SEARCH: REVIEW SP VPS/PDC 9 0 ! @ 2 7 8 1 3 5 6 4 VPS/PDC

REMOTE CONTROL Buttons with a small dot on the left side of the name can also be used to operate your JVC TV while holding down the TV button. Z "Operating JVC TVs" on page 47. 1 TV Button enables remote control of your JVC TV. Z "Operating JVC TVs" on page 47. 2 TV/VCR Button switches connected JVC TV's mode between TV and AV. Z "Operating JVC TVs" on page 47. 3 REVIEW Button — same as button on recorder. Z pg. 17 4 NUMBER Keys are used in preset position selection Z pg. 10, Video Plus+ timer program- ming Z pg. 12. 5 PDC Button enables/disables PDC recording. Z pg. 13, 15 * VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder. 6 X Button cancels timer-programme. Z pg. 16 0000 Button resets counter to 0:00:00. Z pg. 11 7 STOP +/– Button inputs programme Stop Time. Z pg. 14 8 START +/– Button accesses Regular Program screen; inputs programme Start Time. Z pg. 14 9 PROG Button accesses Video Plus+ Program screen. Z pg. 12 0 Button accesses Program screens/displays to check the programme that you have pro- grammed (next programme's information screen appears each time button is pressed). Z pg. 16 ! Rewind [REW] Button — same as button on recorder. Z pg. 8, 9 @ Record Button — same as button on recorder. Z pg. 10 # Stop Button — same as button on recorder. Z pg. 8 $ MENU Button accesses Menu screen. Z pg. 18 % %fi Button is used for selection in on-screen menus. Z pg. 18 TV PROG +/– selects the connected JVC TV's channel. Z "Operating JVC TVs" on page 47. ^ STANDBY/ON Button — same as button on recorder. & AUDIO Button changes output sound mode. Z pg. 21 (TV Muting) Button mutes sound of connected JVC TV. Z "Operating JVC TVs" on page 47. * DISPLAY Button — same as button on recorder. Z pg. 11 ( DAILY Button enables timer recording of daily serials. Z pg. 13, 15 TV PR OG + TV PR OG – T V – T V + TV 0000 START DEBUT STOP FIN DATE MENU OK TV PROG TV/VCR DAILY/QTDN. VPS/PDC AUX ? WEEKLY/HEBDO PROG 30 SEC – –:– – AUDIO 1 2 3 4 5 6 7 8 9 0 2 4 1 3 EXPRESS y u t * p 2 7 6 5 1 8 3 9 4 0 ! @ # $ ^ & w q ) ( e r o i % Q This remote control transmits A code signals only; it is not applicable to B code signals.

weekly serials. Z pg. 13, 15 q AUX Button selects recorder's auxiliary input mode. Z pg. 24 w ‰ Button engages timer-standby mode. Z pg. 13, 15 e DATE +/– Button inputs date of programme for timer recording. Z pg. 14 r TV PROG +/– Button — same as button on recorder. Z pg. 10 t 30 SEC Button initiates a 30-second period of fast-motion playback. Z pg. 17 y Auto Tracking Button enables/disables auto tracking mode during playback Z pg. 20 SP/LP Button selects tape speed. Z pg. 10 u Play Button — same as button on recorder. Z pg. 8, 9 i Fast Forward Button — same as button on recorder. Z pg. 8, 9 o Pause Button — same as button on recorder. Z pg. 9 p OK Button enters selections made in on-screen menus. Z pg. 18 Q Button initiates functions such as Index Search Z pg. 17, variable-speed search, frame by frame playback. Z pg. 9 TV +/–Button controls volume of connected JVC TV. Z "Operating JVC TVs" in the right column. How To Use The remote control can operate most of your video recorder's functions, as well as basic functions of JVC TV sets. (See below.) ●Point the remote control toward the sensor window. ●The maximum operating distance of the remote control is about 8 m. Operating JVC TVs To operate your TV, while holding down the TV button, press the corresponding button: STANDBY/ON , TV/ VCR, TV PROG +/–, TV +/–, (TV Muting). NOTES: ●When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover. ●Depending on the type of JVC TV, there may be cases where some or all functions cannot be operated using the remote control. ●If the remote control doesn't work properly, remove its batteries, wait a short time, replace the batteries and then try again. % %

EK Printed in Japan 0498HOV*UN*VP VICTOR COMPANY OF JAPAN, LIMITED GENERAL Power requirement : AC 220 – 240 V`, 50/60 Hz Power consumption Power on : 24 W Power off : 5.5 W Temperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD) : 400 x 94 x 340 mm Weight : 3.8 kg Format : VHS PAL standard Maximum recording time (SP) : 240 min. with E-240 video cassette (LP) : 480 min. with E-240 video cassette VIDEO/AUDIO Signal system : PAL-type colour signal and CCIR monochrome signal, 625 lines/50 fields Recording system : DA4 (Double Azimuth) helical scan system Signal-to-noise ratio : 45 dB Horizontal resolution : 250 lines Frequency range : 70 Hz to 10,000 Hz (Normal audio) 20 Hz to 20,000 Hz (Hi-Fi audio) Input/Output : 21-pin scart connectors (IN/OUT x 1, IN x 1) RCA connectors (AUDIO OUT x 1) TUNER/TIMER TV channel storage capacity : 99 positions (+AUX position) Tuning system : Frequency synthesized tuner Channel coverage : UHF channels 21 – 69 (470 – 862 MHz) Aerial output : UHF channels 22 – 69 (Adjustable) Memory backup time : Approx. 10 min. ACCESSORIES Provided accessories : RF cable, Infrared remote control unit, "AA" battery x 2 Specifications shown are for SP mode unless otherwise specified. E.& O.E. Design and specifications subject to change without notice. SPECIFICATIONS