Kenwood TM-D700 E Instruction Manual

KENWOOD FM transceiver. KENWOOD always provides Amateur Radio products which surprise and excite serious hobbyists. This transceiver is no exception. This time KENWOOD presents a mobile with a built-in TNC to make data communications much more convenient than before. KENWOOD believes that this product will satisfy your requirements on both voice and data communications. MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual. TM-D700A: 144/440 MHz FM Dual Bander (U.S.A./ Canada) TM-D700E: 144/430 MHz FM Dual B ...

7 Select the desired frequency as the upper limit. 8 Press [F]. 9 Turn the Tuning control, or press Mic [UP]/ [DWN], to select a matching channel in the range U0 to U9. • If you have selected for example L3 in step 5, select U3. 10 Press [M.IN]. • The upper limit is stored in the channel. To confirm the stored scan limits, press [MR], then select the L and U channels. Note: N The lower limit must be lower in frequency than the upper limit. N The lower and upper frequency step sizes must be equal. N The lower and upper limit ...

by circuit failure. m elb o r P e s u a C elb a b o r P n oitc A e vitc e rr o C e g a P .fe R r e w o p t o n lli w r e vie c s n a rt e h T V 8 . 3 1 a g nitc e n n o c r e tf a p u g nis s e r p d n a ylp p u s r e w o p C D e h t R W P g nih t o N . h cti w s .y alp sid e h t n o s r a e p p a 1 d e tc e n n o c s a w elb a c r e w o p e h T .s d r a w k c a b 1 elb a c r e w o p C D d eilp p u s e h t tc e n n o C :yltc e rr o c d e R → k c al B ;) + ( ...

When placing the main unit on such a surface as a desk top, use the supplied cushions to prevent the surface from being scratched. Attach the 4 pieces of cushions to the specified positions on the rear of the main unit. Note: Attach all the cushions to the flat surface on the main unit; otherwise the installation will be unstable or the cushions may come off easily. MODULAR PLUG CABLE CONNECTION Use the supplied modular plug cable to connect the front panel to the main unit. Connect the 4-pin plug to the front panel and 6-pin plug to the main unit. Note: The ...

r etti m s n a r T d n a B F H V d n a B F H U t u p t u o r e w o P h gi H W 0 5 W 5 3 m uid e M W 0 1 .x o r p p A w o L W 5 .x o r p p A n oit alu d o M e c n a tc a e R s n ois si m e s u oir u p S s s el r o B d 0 6 – n oit aiv e d y c n e u q e rf m u m ix a M ± z H k 5 ) n oit alu d o m % 0 6 t a ( n oitr o tsid oid u A s s el r o % 3 e c n a d e p m i e n o h p o r ci M 0 0 6 Ω r e vie c e R d n a B F H V d n a B F H U y rtiu c ri C e n y d o r e t e h r ...

If the fuse blows, determine the cause, then correct the problem. After the problem is resolved, replace the fuse. If newly installed fuses continue to blow, disconnect the power cable and contact your authorized KENWOOD dealer or an authorized KENWOOD service center for assistance. Only use fuses of the specified type and rating; otherwise the transceiver could be damaged. Note: If you use the transceiver for a long period when the vehicle battery is not fully charged, or when the engine is OFF, the battery may become discharged, and will not have sufficient reserves ...

current settings of the HF transceiver as below: q HF frequency w VFO: A, VFO: B, MR: 00 ~ 99 (memory channel number) e RIT, XIT r OFF, –9.99 ~ +9.99 t LSB, USB, CW, FM, or AM y SPLIT–A: VFO A is used for transmitting. SPLIT–B: VFO B is used for transmitting. SPLIT–M: A memory channel is used for transmitting. u “FS” appears when Mic [ ] is pressed. Note: N After pressing [MENU], you can access only Menu 4–4. N The Transporter will transmit its call sign in Morse every 10 minutes, using the 144 MHz band. N The APO timer does ...