KitchenAid YKEBC208KS1 Installation Instructions

[] EbctdcaU requirements [] [] installation steps If you need assistance: Check your Use and Care Guide for a toll-free number to call or call the dealer from whom you purchased this appliance. The dealer is listed in the Yellow Page of your phone directory under "Appliances- Household -- Major -- Service and Repair." Call when you: [_ Have questions about builtqn oven installation o operation, [_ Need to obtain the name and number of an authorized service company. When you call, you will need: [_ The builtqn oven model number. [_ The built-in oven serial number. Both numbers are listed on the model/serial rating plate, located on the oven door or on the oven frame

recessed 49-I/2" {12&7 ore) recessed height 23" (58,4 ore) reax. recessed depth 7 27-3/4" {7&5 ore) rein, cutout height2_ "_------30"(7&2 cre) rein,_ cab net wdth 28=1/2" {72,4 ore) cutout width Singmeoven undercounter {without cooktop installed above) 1-1/2" (3.8 crel rein, top of cutout to underside of countertop 49-3/4" (126,4 ore) rein, cutout height 5ol/4" {13.3 ere) bottom of cutout to floor 1=1/2" (&8 ore} rein_ bottom of cutout to top of cabinet door 3e" (7&2 crel min, cabinet 28=1/2" _{72,4 cre)_ cutout width cabinet_-_- 23=1/4" (59,1 crel rein, cutout depth 23" (58.4 ore) _---recessed oven_ depth J recessed oven _ oven front Cabinet side view Cabinet filler kits are available from your dealer. Use a matching color kit if oven is smaller than your cabinet opening. Single oven filler height is 3o5/16" (8.4 cm) Black -- 4378941 White -- 4378942 Almond- 4378943 Double oven filler height is 6o5/16" (16 cm) Black -- 4378947 White -- 4378948 Almond- 4378949 27=3/4" {7&5 ore} rein, cutout height 1=1/2" (3,8 ere) rein, bottom of cutout to top of cabinet door Doubmeoven 30" (76.2 ore} rein, cabinet width 28=1/2" _----{72,4 cre}------:b, cutout width Singmeoven .j- 5I" {12e.5 ore) reS)L overall height i 1" (2,5 ore} top of cutout to bottom of upper cabinet door 14=3/4" {37.5 ore) bottom of cutout to floor 1" (2,5 ore} top of cutout to bottom of upper cabinet door 32" {813 ore) bottom of cutout to floor Year safety aRd the safety of ethers are very important. We have provided many important safety messagesin this manual and on your appliance. Always readand obey alI safety messages. This is the safety alert symbol. This symbol alertsyou to potential hazardsthat can kill or hurt you and others. AIi safety messageswiii foiiow the safety alert symbol andeither the word "DANGER"or "WARNING"=Thesewords mean: Youcan be killed or seriously injuredif you don't fellow instructions. AtIsafety'messageswilI tetI you what the potentiai hazard is, teii you how to reducethe chanceof injury, andteli you what can happenif the instructions are not followed. important: Observe all governing codes and ordinances. Proper installation is your responsibility. Have a qualified technician install this even. Oven location should be away from strong draft areas, such as windows, doors and strong heating vents. Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. Recessed installation area must provide complete enclosure around the recessed portion of the oven. ElectricaJ ground is required. See "Electrical requirements." Electrical suppJy junction box should be located 3 inches (7.6 cm} maximum below the support surface when oven is installed in a wall cabinet. Drill a 1-inch minimum (2.5 cm} diameter hole in the right rear or left rear corner of the support surface to pass the appliance cable through to the junction box. For undercounter installation, it is recommended that the junction box be located in the adjacent right or left cabinet. If installing the junction box on rear wall behind oven, junction box must be recessed and located in the upper or lower right or left corner of cabinet. It is the customer's responsibility: To contact a qualified electrical installer. To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANa{/NFPA 70 E latest latest edition*, or Canadian L=lectdcalCode, C22.1-1982 and C22.2 No. 01982 (or latest edition)** and all local codes and ordinances. Copies of the standards listed may be obtained from: * National Fire Protection Association Batteryreamh Park Quincy, Massachusetts 02289 _ CSA International 8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575 Tool _/ PhimHps screwdriver Partssupplied: 4 screws (double oven) Page 1

gauge are in accordance with _oca_codes. Do Not ground to a gas pipe. Check with a qualified electrician if you are not sure oven is proper_y grounded. Do Not have a fuse in the neutral or grounding circuit. This oven must be connected to a grounded metal permanent wiring system. Oven must be connected to the proper eUectdcaUvoffage and frequency as specified on the model/serial rating plate. (The model/serial rating plate is located on the oven door or on the oven frame.} [_ Models rated from 7.3 to 9.6 kW at 240 volts (5,5 to 7,2 kW at 208 volts} require a separate @-ampere circuit. Models rated at 7.2 kW and below at 240 volts (5.4 kW and below at 208 volts} require a separate 30°ampere circuit. [_ A timeodelay fuse or circuit breaker is recommended. [_ Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with grounding wire). [_ Flexible armored cable from appliance should be connected directly to junction box. [_ Fuse both sides of the line. [_ A U.L.-listed conduit connector must be provided at the junction box. [_ Do Not cut the conduit. Wire sizes and connections must conform with the rating of the appliance and to the requirements of the National Electrical Code, ANSVNFPA 70 -- latest edition _, or Canadian Electrical Code, C22.1-1982 and C22.2 No. 01982 (or latest edition) *_ and all local codes and ordinances. if the house has aluminum wiring, follow the procedure below. a.) Connect the aluminum wiring to the copper wire using special connectors designed and Underwriters Laboratories° listed for joining copper to aluminum. Follow the electrical connector manufacturer's recommended procedure. b.) Aluminum/copper connection must conform with local codes and industry- accepted wiring practice. Copies of the standards listed may be obtained from: National Fire Protection Association Ratterymamh Park Quincy, Massachusetts 02269 ** CSA International 8501 East Pleasant Valley Road Cleveland, Ohio 44131=5575 _ Grasp oven frame to lift oven, I IB _ power suppBy cable ] Remove _ shipping feet. Use screws to attach oven to cabinet. Reattach side trim. Remove trim screws. Remove side trim. _J_ Grasp oven frame to lift oven. Use screws to attach oven to cabinet. [eattach side trim. Remove side trim. Preparation Excessive Weight Hazard Use two or more people to move and install oven. Failure to follow this instruction can result in back or other injury. Important: Use both hands to remove oven doors. Do Not use handle or any portion of the front frame or trim for lifting. Before moving oven across floor, check that oven is on shipping base or slide oven onto cardboard or hardboard. Do Not remove shipping feet at the front lower corners of oven, Do Not remove shipping feet. l m Turn power supply off. Move oven close to final position. , Remove and discard shipping materials, tape and protective film from the oven. Do Not remove shipping base or shipping feet at the front _ower corners of oven. The shipping feet will protect the _ower oven trim until oven is inserted into cabinet. , Remove and set aside racks and other parts from inside oven. Remove oven door. power X supply cable X Remove shipping feet. Remove trim $srews. Remove oven doors, Replace oven doe! match on the hinge in locked position = door free to open and close latch on the hinge in unlocked position = door ready for removal Remove trim screw. Puff trim out, Pull top of trim down, m Completely open oven door. in both back corners of the door you will see door latches in the locked position. Rotate both latches forward to the unlocked position. Grasp outside edges of door with both hands. Begin closing door, at the moment the door stops closing, lift and puii door toward you. Set door aside on a protective surface. 3u Remove trim screws attaching right and left side trim to oven. Grasp the bottom end of trim and pull away from oven. Slide top end of trim downward to remove trim from oven. Take care not to scratch other surfaces with ends of trim. Set trim and screws aside on protected surface. Page 2

"Electrical requirements", Page 2. Electrical 8hock Hazard Turn power supply off before connecting wires. Use 8 gauge solid copper wire. Electrically ground range. Failure to follow these instructions can result in death, fire, or electrical shock. This oven is manufactured with white {neutral) power supply wire and a cabinet=connected bare grounding wire twisted together. Feed oven cable through opening in the cabinet. Make electrical connection following the steps needed for your installation. 1. Disconnect the power supply. 2. Remove the junction box cover. 3. Connect oven cable to junction box through the U.L.-listed conduit connector. 4. Connect the two black wires together with twist-on connectors. 5. Connect the two red wires together with twist-on connectors. 6. Complete electrical connection according to local codes and ordinances. black "e8 white grounding oven U.L.4isted cable wires -- _ conduit factory crimped cable from connector Figure 1 oven ff local codes PERMIT connecting cabinet- grounding conductor to neutrat white wire in junction box: 7. Connect the factory-crimped bare and white oven cable wires to the neutral (white) wire in junction box. See Figure 1. 8. Replace junction box cover. cable from power supply junction box _J--J L , .= uit Figure 2 cable from connector oven If local codes DO NOT cabinet-grounding conductor to neutram white wire in junction box: 7. Separate the factory- crimped bare and white oven cable wires. 8. Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2. 9. Connect the bare grounding oven cable wire to a grounded wire in the junction box. See Figure 2. 10. Replace junction box cover. ff connecting to a four-wire electricam syste m: 7. Separate bare and white oven cable wires. 8. Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2. 9. Connect the bare grounding oven cable wire to the green grounding wire in junction box. Do Not connect bare grounding wire to neutral {white}wire in junction box. See Figure 2. 10. Replace junction box cover. Attachment Carefully push against seal area of oven front frame when pushing oven into cabinet. Do Not push against outside edges. 5m Lift oven into cob oet cutout os ng the oven ope.nmg as an I_',__ I_7/-_ area to gnp 4 screws Slide top of trim up, ! Push trim into place. Repmace trim screw. Slide top end of each trim upward onto oven side rails. Push each trim into place at bottom of trim. Use screws to attach each trim to oven. Take care not to scratch other surfaces with ends of trim. 8u Replace oven racks. / shipping foot Push against seal area of front frame to push oven into cabinet until shipping feet almost contact cabinet. Use a Phillips screwdriver to remove screws attaching shipping feet. Remove and discard shipping feet. Push oven completely into cabinet and center oven in cabinet cutout. m important: Securely fasten oven to cabinet using the screws provided (two screws for a single oven or four screws for a double oven). Insert the screws through hobs in mounting rails. Do Not overtighten screws. g m Reinstall the oven door by inserting ends of hinges into hinge slots in the oven frame. Push hinges in as far as theywill go. Open the door (you will feel the door drop into place) and rotate both hinge latches back to the locked position. Close and open the door to check that the door closes and opens completely, if door does not dose or open completely, repeat the door removal step and reinstall door as described above. Repeat for lower oven door. Check operation Turn on power supply. The display panel wiii light up briefly. "PF" should appear in the temperature display. / , / , ,f " _i iii : BAKE BBO& iCLEAN \ , , / , / m Check the operation of your single oven. Press the "BROIL" pad. "BROIL" will appear in the display. Press the "START" pad. Make sure the oven door is closed and the "ON" light is shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Press the "CANCEL" pad. Check the operation of your double oven. Press the "Upper Oven" pad. Pressthe "BROIL" pad. "BROIL" will appear in the display. Pressthe "START" pad. Make sure the oven door is closed and the "ON" light is shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Press the "CANCEL" pad. Press the "Lower Oven" pad and repeat the steps you completed for checking the upper oven. if your oven does not heat or an "F', followed by a number, appears in the disptay, contact your dealer or check the "if you need service..." section of this Installation instructions. To get the most efficient use from your new oven, read your Use and Care Guide.Keep installation instructions and Guide close to oven for easy reference. Page 3

[_ Check that circuit breaker is not tdpped or house fuse Nown, [_ See Use and Care Guide for trouMeshoofing [[st. if you need assistance: ff you have questions about operating, cleaning or maintaining your oven: [_ Refer to Use and Care Guide. [_ Ca[[the Consumer Assistance Center: Check your Use and Care Guide for a to[[- free number to ca[[ or ca[[ the dealer from whom you purchased tMs appliance. The dealer is listed in the Yellow Pages of your phone directory under "Appliances -- HousehoM -- Major -- Service and Repair." if you need service: Maintain the qud[ty built into your built-in oven by calling an authorized service company. To obtain the name and number of an authorized service company: [_ Contact the dealer from whom you purchased your bu[[tqn oven; or [_ Look in the Yellow Pages of your telephone directory under "Appliances -- Household -- Major -- Service and Repair" for an authorized service company; or [_ Call the Consumer Assistance Center. The toll free phone number is listed in your Use and Care Guide. When you ca[[, you wi[[ need: [_ The built-in oven mode[ number. _j The built in oven serial number. Both numbers are listed on the model/serial rating plate, located on the oven door or on the oven frame. Part No. 8300651 O 2001 Printed in U.S.A.