KitchenAid 5KSM7580 Instructions Manual

of bowl are not thoroughly mixed, then the beater is not far enough into the bowl. See the “Setting Up Your Stand Mixer” section. Tips for Great Results Adding Ingredients Always add ingredients as close to side of bowl as possible, not directly into moving beater. The Pouring Shield can be used to simplify adding ingredients. Use Speed 1 until ingredients have been blended. Then gradually increase to desired speed. Adding Nuts, Raisins, or Candied Fruits Follow individual recipes for guidelines on including these ingredients. In general, soli ...

Adjusting your Beater to Bowl Clearance Your Stand Mixer is adjusted at the factory so the Flat Beater just clears the bottom of the bowl. If, for any reason, the Flat Beater hits the bottom of the bowl or is too far away from the bowl, you can correct the clearance easily. 1. Turn speed control to “0” (OFF). 2. Unplug Stand Mixer or disconnect power. 3. Lower the bowl to the down position. 4. Turn Beater Height Adjustment Screw (A) slightly counter clockwise (left) to raise Flat Beater or clockwise (right) to lower Flat Beater. 5. Make adjustme ...

When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. To avoid risk of electrical shock, do not put Stand Mixer in water or other liquid. 3. The appliance is not intended for use by young children or infirm persons without supervision. 4. Unplug Stand Mixer from outlet when not in use, before putting on or taking off parts, and before cleaning. 5. Avoid contacting moving parts. Keep hands, hair, and clothing, as well as spatulas and other utensils away from beater during ope ...

Household KitchenAidTM Bowl-Lift Stand Mixer Warranty Length of Warranty: KitchenAid Will Pay For: KitchenAid Will Not Pay For: Europe, Australia and New Zealand: For the ArtisanTM Mixer 5KSM7580: Five years Full Warranty from date of purchase. For the Heavy Duty Mixer 5KSM7591: One Year Full Warranty from date of purchase. The replacement parts and repair labor costs to correct defects in materials or workmanship. Service must be provided by an Authorized KitchenAid Service Center. A. Repairs when Stand Mixer is used for operations other than normal household ...

Volts: 220-240 A.C. Hertz: 50/60 Hz NOTE: The power rating for your Stand Mixer is printed on the serial plate, placed under your Stand Mixer. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance. The wattage rating is determined by using the attachment that draws the greatest load (power). Other recommended attachments may draw significantly less power. Electrical Requirements This appliance is marked according to the European directive 2002/96/EC on Waste Electrical an ...

All speeds have the Soft Start feature that automatically starts the Stand Mixer at a lower speed to help avoid ingredient splash- out and “flour puff” at start-up, then quickly increases to the selected speed for optimal performance. Speed Used for Accessories Description 1 Stirring For slow stirring, combining, mashing, starting all mixing procedures. Use to add flour and dry ingredients to batter, and add liquids to dry ingredients. Do not use Speed 1 to mix or knead yeast doughs. 2 Slow Mixing, For slow mixing, mashing, faster stirring. Kneading Use to ...

Adjusting your Beater to Bowl Clearance Your Stand Mixer is adjusted at the factory so the Flat Beater just clears the bottom of the bowl. If, for any reason, the Flat Beater hits the bottom of the bowl or is too far away from the bowl, you can correct the clearance easily. 1. Turn speed control to “0” (OFF). 2. Unplug Stand Mixer or disconnect power. 3. Lower the bowl to the down position. 4. Turn Beater Height Adjustment Screw (A) slightly counter clockwise (left) to raise Flat Beater or clockwise (right) to lower Flat Beater. 5. Make adjustme ...