LG GP08NU10 Quick Setup Manual

Sensitive Devices, you may use anti-static products such as wrist straps, heel straps, mats to protect your body from electrostatic. • Make sure you have a personal computer with an open USB port before connecting the drive to your computer. • Power for all other devices should be turn off before attaching the cables. Connect the drive to the computer as shown in figure. A. Using an USB 2.0 cable only. 1. Connect the USB 2.0 cable to the External Super Multi DVD Rewriter. 2. Connect the other end of the USB 2.0 cable to your computer. B. Using USB 2.0 Cable and USB Power cable. (DC-jack type) 1. Connect the USB 2.0 cable to the External Super Multi DVD Rewriter. 2. Connect the other end of the USB 2.0 cable to your computer. 3. Connect the USB power cable (DC-jack type) to the External Super Multi DVD Rewriter. 4. Connect the other end of the USB power cable to your computer. • The Rewriter may get its power from the USB power. All systems may not meet USB power requirements and full performance may not be achieved. In this case, connect to the included USB power cable (DC-jack type.). • Please do connect the USB cables by any means other than specified above. Using the wrong type of cable with this drive can cause it to malfunction. When the computer is ready, confirm that the drive is detected. And then, insert the supplied software CD into the External Super Multi DVD Rewriter and install the software. • The machine does not have an ON/OFF switch. As soon as it is connected to the AC power, the power up sequence begins. The power supply cord is intended to serve as the main disconnect device. The power outlet shall be near the equipment and shall be easily accessible. • The appliance is not intended for use by young children or infirm persons without supervision. • Young Children should be supervised to ensure that they do not play with appliance. • If the appliance is supplied from a cord extension set or an electrical portable outlet device, the cord extension set on electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture. Installation USB Power cable (DC-jack type) NOTES Connecting to computer Hardware Installation NOTES NOTES A. Using an USB 2.0 cable only. B. Using USB 2.0 Cable and USB Power cable. (DC-jack type) USB 2.0 cable USB 2.0 cable

2. Drive activity indicators The LED used to indicate the operation of External Super Multi DVD Rewriter. 3. Eject Button 4. Emergency Eject Hole 1. Power Connector This connector is used to connect to the USB power cable. (DC-jack type) Or, this connector is used to connect to the AC Power adapter cord (5V, 2A, outside diameter: 4mm, inside diameter: 1.75mm) (Not supplied). 2. USB Connector This connector is used to connect to the USB 2.0 cable. Location and function of controls Removing the USB converter cable (For Windows) The drive supports the plug and play(not swap) function of Windows, and can be removed and inserted by performing the following operation. 1. Stop the application software being currently used. 2. Click the icon “ ” of the taskbar located on your screen’s bottom right side. 3. Click “Safely Remove USB Mass Storage Device-Drive[x:]”. 4. Click “Ok” and then remove the USB converter cable. 1 2 3 4 This following is the general figure of the design of the drive. The drive’s appearance and specifications may change without prior notice. Front Rear 1 2 NOTE Don’t remove the USB 2.0 cable when the busy indicator on the drive blinks, or during computer startup. The removing procedure varies depending on your OS.

• Buffer Under Run error protection technology • Emergency eject support • Combination of CD-R/RW, DVD-R/RW, DVD+R/RW, DVD+R DL, DVD-R DL and DVD-RAM drive functions into one drive. • Supports region playback control Phase II. • Supports SecurDiscTM Technology. • Supports LightScribe Direct Label Printing Technology - *Optional. * You can use a variety of Drive System meeting the following requirements is needed in order to use USB 2.0 operation with this drive. • Computer that is equipped with a USB 2.0 – compliant USB connector or PCI adapter card, and on which the USB 2.0 EHCI (Enhanced Host Controller Interface) driver software 1) has been installed. 1) The USB 2.0 EHCI driver software is supplied with currently available PCI adapter cards that conform to USB 2.0. Further, Microsoft has released the USB 2.0 EHCI driver software for Windows XP, therefore it is also possible to use this driver software with Windows XP. If you want to know in detail, please contact your USB 2.0 adapter dealer or consult your PC manufacturer, or consult the Microsoft Corporation Web site. System Environment Computer This unit can be operated in the system environment explained here. * For Windows Vista, 512MB of RAM or large is recommended. * Compatibility problem in write/read function may occur with some media depending on the media manufacturing quality. * To achieve maximum Record & Write speed your system may require data to be copied first to the computer’s hard drive rather than directly from another source disc or drive. Specifications Pentium III 1.0GHz or Higher(with USB 2.0) for basic performance (Recommended for optmal performance: Pentium IV 2.4GHz or Higher). 256MB or larger (Recommended: 512MB). 20GB or more free space. (The free space needed for writing depends on the quantity of data.) 64MB (Recommended: 128MB). USB 2.0 port For Software installation Windows Vista/Windows XP Home Edition/Professional Direct X 9.0 or Higher Mac OS X: Ver 10.4.10 or Higher CD-R : LG, Mitsubishi Kagaku Media, Verbatim, That’s, TDK, Ritek or HP discs are recommended. CD-RW : LG, Mitsubishi Kagaku Media, Verbatim are recommended. DVD-R : Mitsubishi Kagaku Media, Maxell, That’s are recommended. DVD-RW : Victor. JVC, Mitsubishi Kagaku Media, TDK are recommended. DVD+R : Mitsubishi Kagaku Media, That’s, Maxell are recommended. DVD+RW : TDK, Mitsubishi Kagaku Media, Ricoh are recommended. DVD-RAM : Maxell, Mitsubishi Kagaku Media are recommended. DVD±R DL : Mitsubishi Kagaku Media, Verbatim are recommended. System requirements Hard disk Video Memory Interface CD-ROM drive Software Required OS CD-R, CD-RW, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, DVD±R DL discs CPU Memory ❋ The drive’s appearance and specifications may change without prior notice. - The maximum data transfer rate varies according to the performance capabilities of the PC. - For the sake of periodic improvements, specifications and appearance are subject to change without notice. - We have taken all possible measures to assure the quality of our products, but we cannot be responsible for the consequences if defect occurs. Software Install the appropriate CD Recording Authoring Software before using this unit. * Please uninstall any previous CD burning software you may have loaded on your PC in order to prevent possible compatibility issues. Once you have installed the application software, you may (if you wish) begin to reinstall previous software, taking note for errors. We recommend using the drive with the latest software as some problems encountered when using the drive can be solved by updating the software. * For more SecurDiscinformation, visit http://www.securdisc.net Please visit www.lgservice.com and install the program, “LG ODD Online F/W update.” By using the program, you can automatically check the latest information about FirmWares and update the FirmWare. Worldwide support ; http://www.LGservice.com Worldwide corporate site : http://www.LGE.com Supported Discs DVD-ROM(Single/Dual), DVD-RW, DVD-R, DVD+RW, DVD+R, DVD+R Double layer, DVD-R Dual layer, DVD- RAM, CD-Digital Audio & CD-Extra, CD-Plus, CD-ROM, CD-ROM XA-Ready, CD-I FMV, CD-TEXT, CD-Bridge, CD-R, CD-RW, Photo-CD (Single & Multi-Session), Video CD, DVD-VIDEO Dimensions (WxHxD) 156 x 21 x 165mm Weight About 380g Interface USB 2.0 Read/Write Speed Write : (DVD-R): 2x CLV, 4x ZCLV, 8x CAV (DVD-R DL): 2x CLV, 4x ZCLV, 6x ZCLV (DVD-RW): 2x CLV, 4x, 6x ZCLV (DVD-RAM): 2x, 3x ZCLV, 5x PCAV (Ver. 2.0 & higher) (DVD+R): 2.4x CLV, 4x ZCLV, 8x CAV (DVD+R DL): 2.4x CLV, 4x ZCLV, 6x ZCLV (DVD+RW): 2.4x, 3.3x CLV, 4x ZCLV, 8x ZCLV (CD-R): 10x CLV, 16x, 24x ZCLV (CD-RW): 4x, 10x CLV, 16x ZCLV, 24x ZCLV (High Speed: 10x CLV, Ultra Speed > 16x ZCLV Ultra Speed plus > 16x ZCLV) Read : (DVD-R/RW/ROM): 8x/8x/8x max. (DVD-R DL): 8x max. (DVD-RAM) (Ver.2.0 & Higher): 5x max. (DVD-Video) (CSS Compliant Disc): 4x max. (DVD+R/+RW): 8x/8x max. (DVD+R DL): 8x max. (CD-R/RW/ROM): 24x/24x/24x max. (CD-DA (DAE)): 24x max. Data transfer rate Sustained CD-ROM : 3,600 Kbytes/s (24X max) DVD-ROM : 11.08 Mbytes/s (8X max) Average Access CD-ROM : 140msec (Typical) Time (1/3 Stroke) DVD-ROM : 160msec (Typical) DVD-RAM : 360msec (Typical) Buffer capacity 2 Mbytes MTBF 60,000 Power On Hours (Duty Cycle 10%) Supported CD-R, CD-RW, DVD+R, DVD+RW, DVD-R, SecureDiscs DVD-RW, DVD+R DL, DVD-R DL, DVD-RAM Power Requirement 5V DC Operating Environment Temperature 5 to 40 °C Humidity 15 to 80 % Storage Environment Temperature -30 to 60 °C Humidity 10% to 90% RH Item Quantity - External Super Multi DVD Rewriter 1 - USB 2.0 cable 1 - USB Power cable (DC-jack type) 1 - Software CD 1 - Quick Guide for Drive 1 Quick Set-up Guide External Super Multi DVD Rewriter GP08 To install of your product, please read this guide manual carefully and completely. For the detailed owner’s manual of the drive, please refer to the CD manual. P/NO. 3828HN1012X Ver. B Package Items GP08LU10 GP08NU10 Light Scribe X I/F USB 2.0 only USB 2.0 only Cautions

2004/108/EC et 2006/95/EC. Questo prodotto risponde alle direttive EMC 2004/108/EC e 2006/95/EC, relative alla compatibilità elettromagnetica. Este producto ha sido fabricado cumpliendo los requisitos sobre interferencias de radio de la DIRECTIVAS EMC 2004/108/EC y 2006/95/EC. CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT CLASE 1 PRODUCTO LÁSER CLASSE 1 PRODOTTO LASER CAUTION : CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.AVOID EXPOSURE TO THE BEAM. ADVARSEL : KLASSE 3B SYNLIG OG USYNLIG LASERSTRÅLING I ÅBEN TILSTAND OG VED AFBRUDT LÅSEFUNKTION. UNDGÅ AT BLIVE RAMT AF LASERSTRÅLEN. VARO! : LUOKKA 3B AVATTAESSA JA KUMOTTAESSA LUKITUS NÄKYVÄÄ JA NÄKYMÄTÖNTÄ LASERSÄTEILYÄ. VÄLTÄ LASERSÄTEILLE ALTISTUMISTA. ATTENTION : CLASSE 3B RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D’OUVERTURE ET ENCLENCHEMENTS DEFECTUEUX, EVITER L'EXPOSITION AU FAISCEAU. VORSICHT : SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG DER KLASSE 3B WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT VERMEIDEN SIE ES, SICH DEM STRAHL AUSZUSETZEN. ADVARSEL : KLASSE 3B SYNLIG OG USYNLIG LASERSTRÅLING NÅR ÅPNES OG LÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN. VARNING : KLASS 3B SYNLIG OCH OSYNLIG LASERSTRÅLNING FÖREKOMMER NÄR OCH MELLANLÅSET FÖRSTÖRS. UNDVIK EXPONERING UNDER STRÅLEN. Dieses Produkt erfüllt die Funkstörungsanforderungen folgender Normen: 2004/108/EC und 2006/95/EC. This product is manufactured to comply with the radio interference requirements of EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC. ■ Microsoft® and Windows® are trademarks registered in the United States and other countries by the Microsoft Corporation. ■ The company names and product names written in this manual are trademarks or registered trademarks of the respective companies. Industry Canada requirement This class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC COMPLIANCE STATEMENT Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an Authorized Service Center for help. • FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This External Super Multi DVD Rewriter is for use only with UL listed personal computers that have installation instructions detailing user-installation of card cage accessory. CAUTION: The laser used in the External Super Multi DVD Rewriter can damage your eyes. Do not attempt to open the cover. To reduce the risk of electric shock, do not remove the cover (or back). There are no user-serviceable parts inside. Refer servicing to qualified service personnel. Use of controls or performance of procedures other than those specified herein may result in hazardous radiation exposure. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.a VORSICHT : Der in diesem External Super Multi DVD -Laufwerk benutzte Laser kann Ihre Augen schädigen. Versuchen Sie keinesfalls, die Abdeckung zu öffnen. Um die Gefahr eines elektrischen Schocks zu reduzieren, sollten Sie die Abdeckung (oder Rückseite) keinesfalls entfernen. Im Inneren des Geräts befinden sich keine Teile, die vom Benutzer selbst gewartet werden können. Überlassen Sie die Wartung qualifizierten Kundendiensttechnikern. Beachten Sie bei der Benutzung von Bedienelementen und der Durchführung von Prozeduren unbedingt die Anweisungen dieses Handbuchs, da andernfalls gefährliche Strahlung freigesetzt werden kann. WARNUNG : Setzen Sie das Laufwerk keinesfalls Regen oder Feuchtigkeit aus, um die Gefahr eines Brandes oder elektrischen Schocks zu reduzieren. ATTENTION: l'exposition au laser utilisé dans le super graveur multi-DVD présente un danger pour les yeux. N'essayez pas d'ouvrir le capot. Afin de réduire les risques de chocs électriques, ne retirez pas le capot (ni l'arrière du dispositif). Aucune pièce interne ne peut être remplacée par l'utilisateur. Pour la maintenance de l'appareil, adressez-vous au personnel qualifié du service de maintenance. L'utilisation de commandes ou de procédures différentes de celles spécifiées ci-après peut entraîner une exposition à des rayons dangereux. AVERTISSEMENT :Ne pas exposer ce matériel à la pluie ou à l’humidité (risques d’incendie et d’électrocution). PERICOLO : Il dispositivo di lettura e scrittura utilizzato in questo masterizzatore utilizza un raggio laser che, se osservato da vicino, può danneggiare la vista. Evitare di smontare il coperchio dell’apparecchio. Al fine di prevenire eventuali folgorazioni, evitare di smontare l’apparecchio. All’interno dell’apparecchio non sono presenti parti che richiedono manutenzione da parte dell’utente. In caso di difetti o guasti, rivolgersi ad un Centro di Assistenza Tecnica. L’esecuzione di procedure diverse da quella espressamente indicate in questo manuale può provocare pericolose esposizioni alle radiazioni laser. ATTENZIONE: Al fine di evitare cortocircuiti o principi di incendio, evitare di esporre questo apparecchio alla pioggia o ad una eccessiva umidità ambientale. PRECAUCION: El láser utilizado en la unidad External Super Multi DVD puede dañar sus ojos. No intente abrir la tapa. Para reducir el riesgo de descarga eléctrica, no quite la tapa (ni la parte posterior). No hay piezas internas que deba mantener el usuario. El servicio de mantenimiento debe efectuarlo personal técnico cualificado. El uso de controles o la ejecución de procedimientos distintos de los especificados en este manual pueden ser causa de exposición a radiación peligrosa. ADVERTENCIA: Para reducir el riesgo de fuego o descarga eléctrica, no exponga este aparato a la lluvia ni a la humedad. CUIDADO: O laser utilizado na unidade Super Multi DVD pode causar lesões oculares. Não tente abrir a tampa. Para reduzir o risco de choques eléctricos, não retire a tampa (quer frontal quer superior ). A unidade não contém peças que possam ser reparadas pelo utilizador. Deixe a manutenção para um técnico da assistência qualificado. A utilização de controlos ou a execução de procedimentos que não sejam os especificados neste manual podem causar a exposição a radiações perigosas. AVISO: Para reduzir o risco de incêndio ou choque elétrico não exponha este aparelho á chuva ou humidade.