Liebherr HF 861 Installation Instructions Manual

integrated use, door-on-door Instrucciones de montaje Frigorífico y congelador, integrable, puerta fija Instructions de montage Congélateurs et réfrigérateurs, intégrables, porte fixe HRB 1120 / HF 861 040414 7085580 - 00

2 2 Transporting the appliance.......................... 2 3 Setting up the device.................................... 2 4 Appliance dimensions................................... 4 5 Recess dimensions....................................... 4 6 Cabinet door................................................... 4 7 Kitchen cabinet setup for the water filter.... 7 8 Air circulation in the kitchen cabinet........... 7 9 Reversing the door........................................ 8 10 Water connection........................................... 11 11 Installing the appliance in the recess.......... 12 12 Installing the water filter............................... 21 13 Disposal of packaging................................... 22 14 Connecting the appliance............................. 23 The manufacturer is constantly working to improve all models. Therefore please understand that we reserve the right to make design, equipment and technical modifica- tions. To get to know all the benefits of your new appliance, please read the information contained in these instruc- tions carefully. The instructions apply to several models, so there may be differences. Sections which only apply to certain appli- ances are indicated with an asterisk (*). Instructions for action are marked with a , the results of action are marked with a . 1 General safety information - Read and follow these instructions. They contain safety advice which is important for safe and problem-free installation and opera- tion. Always read and follow the safety advice. - It is important that the guidelines and instruc- tions in this manual are followed so that the appliance is correctly installed and operates properly Read and understand all information in this manual before the appliance is installed - Risk of asphyxiation and crushing: Remove doors and shelves from old appli- ances to prevent them from becoming a poten- tial hazard to children at play. - Only install, connect and dispose of the appli- ance in accordance with the instructions. Pay particular attention to “niche dimensions” (see 5) and “ventilation and fume extraction in kitchen units” (see 8) . - The socket must be easily accessible so that the appliance can be disconnected from the mains quickly in an emergency. It must not be behind the back of the appliance. DANGER indicates a hazardous situation, which if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation, which if not avoided, could result in death or serious injury. CAUTION indicates a hazardous situation, which if not avoided, will result in minor or moderate injury. NOTICE indicates a hazardous situation, which if not avoided, could result in damage to property. Note indicates useful advice and tips. 2 Transporting the appliance CAUTION Risk of injury or damage if incorrectly transported. u Transport the appliance in its packaging. u Transport the appliance upright. u Do not move the appliance on your own. 3 Setting up the device WARNING Risk of fire due to short circuit. If the power cable or plug of the appliance or another appliance and the back of the appliance touch each other the power cable or plug will be damaged by the vibrations of the appliance which could lead to a short circuit. u Install the appliance so that it does not touch any plugs or power cables. u Do not connect the appliance or other appliances to the sockets on the back of the appliance. WARNING Risk of fire due to moisture! If live parts or the power cord get wet, this can cause a short circuit. u The appliance is designed for use in enclosed spaces. Do not operate the appliance in open space or in damp areas or where there is spray. u Only operate the appliance after it has been installed. General safety information 2 * Depending on model and options

The refrigerant contained within the appliance, R 600a, is environmentally friendly, but flammable. Leaking refrig- erant can ignite. u Do not damage the pipes of the refrigerant circuit. WARNING Danger of fire and damage! u Do not place devices that give off heat, e.g. micro- waves, toasters, etc. on the appliance. NOTICE Risk of damage caused by condensation Installing the appliance next to any other refrigerator or freezer can cause condensation or damage to the Lieb- herr appliance. u Do not install this appliance next to any other refriger- ator or freezer except another Liebherr model. Liebherr models are designed to allow side-by-side installation. They are equipped with a heating system to eliminate condensation when refrigerators or freezers are installed side-by-side. NOTICE Risk of damage for the finished floor surface! u Protect the finished floor surface before you uncrate the unit. WARNING Danger of damage from overheating. May restrict opera- tion. u Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction. WARNING Danger of tilting. u To avoid a hazard due to instability of the appliance, it must be fixed in accordance with the instructions. q If possible, have a professional install the appliance in your kitchen cabinet unit. q If the appliance is damaged check with the supplier immediately before connecting it. q The floor of the installation site must be horizontal and level. q Do not install the appliance in direct sunlight or next to an oven, heater or similar heat source. q Do not install the appliance on your own. It is better to do this with two or more people. q In accordance with EN 378 for each 0.28 oz (8 g) of R 600a refrigerant the room where the appliance is installed must have a volume of 35.5 ft3 (1 m3). If the installation room is too small an inflammable gas/air mixture may arise if the refrigerant circuit leaks. You will find details of the required quantity of refrigerant on the rating plate inside the appliance. q If the appliance is installed in a very damp environment condensate water may form on the outside of the appli- ance. Always ensure good ventilation. q The load-bearing capacity of the floor must be sufficient for the weight of the appliance plus about 1200 pounds (544 kg) of food weight. q The electrical socket must assessed precisely to ensure the correct position and fuse. q Do not restrict ventilation. Sufficient ventilation is required for the appliance to operate correctly. The ventilation grid fitted at the factory guarantees an effec- tive ventilation gap on the appliance of 31 in.2 (200 cm2). If you replace the ventilation grid with a fascia, this must have at least the same size or larger ventilation gap as the manufacturer's ventilation grid. u Note down the type (model, number), appliance name, appliance or serial number, date of purchase and manufacturer's address in the place provided for this in the Use & Care Manual. u Remove all materials that could prevent it from being installed properly or prevent proper ventilation from the back or the side panels of the appliance. u Remove the red transport safety device. Close off any holes that have been revealed with plugs (60). After installation: u Remove protective films, adhesive tapes and transport safety devices, etc. Note u Clean the appliance (see operating instructions, "Cleaning the appliance" section). Setting up the device * Depending on model and options 3

Fig. 1 in. mm A 22 559 B 21 7/16 544 C 69 11/16 1770 5 Recess dimensions This is a built-in appliance and is therefore completely enclosed by a kitchen cabinet The kitchen cabinet surrounding the appliance must be designed exactly in accordance with the specified fitting dimensions and must allow sufficient air circulation to ensure correct operation of the appliance. Fig. 2 in. mm D 69 3/4 — 70 3/8 1772 — 1788 E 22 — 22 3/4 560 — 578 F min. 21 5/8 min. 550 G min. 19 11/16 min. 500 H min. 1 5/8 min. 40 J max. 3/4 max. 19 u For side-by-side installation of two appliances next to each other install each appliance in its own kitchen cabinet. u Check the wall thickness of adjacent cabinets: It must be at least 5/8 in. (16 mm). u Only install the appliance in solid, fixed kitchen cabi- nets. Ensure that the cabinets cannot tip over. u Align the cabinets with a spirit level and a try square. If necessary level them by putting something underneath them. u Ensure that the floor and the side panels of the cabinet are at right angles to each other. 6 Cabinet door - A door is required for the kitchen cabinet. Appliance dimensions 4 * Depending on model and options

than 3/4 in. (19 mm) thick. - There must be a gap of at least 1/8 in. (3 mm) between the door and the cupboard door above it (if there is one). - The width of the cabinet door depends on the style of the kitchen and the size of the gap between the door panels of the cupboard. Normally a vertical gap of 1/8 in. (3 mm) should be left between the cabinet doors. - If there are other cabinets the top edge of the cabinet door should be at the same height as the doors on the adjacent cabinets. - The cabinet door must be assembled flat and free from tension. NOTICE An excessively heavy unit door can cause potential damage! If the unit door is too heavy, we cannot rule out damage to the hinges, which may compromise the use of the unit. u Before installing the unit door, ensure the door does not exceed the permissible weight. Appliance type Maximum weight of unit door HRB 1120, HF 861 50 lbs (23 kg) Total height of the cabinet (i.e. 70 3/8 in. (1788 mm)) plus thickness of the cover and floor plate Fig. 3 (a) (normally 3/4 in. (19 mm)): 70 3/8 in. + 3/4 in. + 3/4 in. = 71-3/16 in. ( 1788 mm + 19 mm + 19 mm = 1808 mm ) Cabinet door * Depending on model and options 5