Estate TMH16XS Dimension Manual

OVERALL DIMENSIONS VENTING REQUIREMENTS TMH16XS Electrical: A 120-volt, 60 Hz, AC-only, 15 or 20 amp electrical supply located in the upper cabinet as close as possible to the microwave oven hood. A time-delay fuse or circuit breaker and separate circuit is recommended. ® Microwave Hood Combination Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice. Ref. 8206587 09-19-06 Recommended standard fittings If the existing vent is round, a rectangular- to-round adapter must be used and a rectangular 3" (7.6 cm) extension vent between the damper assembly and the adapter must be installed to prevent sticking of the exhaust damper. 1 - 3-1/4" x 10" 90° elbow = 25 ft. (7.6 m) 1 - wall cap = 40 ft. (12.2 m) 8 feet straight = 8 ft. (2.4 m) Length of 3-1/4" x 10" system = 73 ft. (22.2 m) 6" (15.2 cm) vent system 3-1/4" x 10" (9.5 cm x 25.4 cm) vent system 1 - transition = 5 ft. (1.5 m) 2 - 90° elbows = 20 ft. (6.1 m) 1 - wall cap = 40 ft. (12.2 m) 8 feet straight = 8 ft. (2.4 m) Length of 6" system = 73 ft. (22.2 m) 3-1/4" x 10" 90° elbow 90° elbows transition wall cap 6 ft. (1.8 m) 2 ft. (0.6 m) 3-1/4" x 10" to 6" = 5 ft. 3-1/4" x 10" roof cap = 24 ft. 3-1/4" x 10" 90° elbow = 25 ft. 90° elbow 6" = 10 ft. 3-1/4" x 10" wall cap = 40 ft. 3-1/4" x 10" 90° flat elbow= 10 ft. 45° elbow 6" = 5 ft. Recommended vent length Use 3-1/4" x 10" (8.3 cm x 25.4 cm) rectangular or 6" (15.2 cm) round vent. The total length of the vent system including straight vent, elbow(s), transitions, wall or roof caps must not exceed the equivalent of 140 feet (42.7 m) of 3-1/4" x 10" (8.3 cm x 25.4 cm) rectangular or 6" (15.2 cm) round vent. For best performance, use no more than three 90° elbows. To calculate the length of system you need, add the equivalent feet for each vent piece used in the system. See examples below. NOTE: There must be at least one 2" x 4" (50.8 cm x 101.6 cm) wall stud and minimum 3/8" (9.5 mm) thickness drywall or plaster/lath within cabinet opening. Must be able to support 150 lbs. (68 kg). * 30" (76.2 cm) is typical for 66" (167.6 cm) installation height. Exact dimensions may vary depending on type of range/cooktop installed below. Roof venting Wall venting roof cap 3-1/4" x 10" (8.3 cm x 25.4 cm) through-the-roof 3-1/4" x 10" (8.3 cm x 25.4 cm) through-the-wall wall cap CABINET OPENING DIMENSIONS For wall or roof venting methods: If the wall exhaust method is chosen, be sure that there is proper clearance within the wall for the damper to fully open. Wall and roof caps must have back-draft damper. We recommend: ✔using rigid metal vent. ✔that length of vent and number of elbows should be kept to a minimum to provide efficient performance. ✔that size of vent should be uniform. ✔using duct tape to seal all joints in the vent system. ✔using caulking compound to seal exterior wall or roof opening around cap. ✔two elbows should not be installed together. We do NOT recommend: ✔flexible metal vent. NOTE: If flexible metal vent must be used, calculate each foot of flexible metal vent as two feet of rigid metal vent. Flexible metal elbows count twice as much as standard elbows. 6 ft. (1.8 m) 2 ft. (0.6 m) 29⁷⁄₈" (76.0 cm) 15³⁄₄" (40.0 cm) 17¹⁄₄" (43.8 cm) 16¹⁄₄" (41.3 cm) 66" (167.6 cm) min. 12" (30.5 cm) min. 14" (35.6 cm) max. A B 30" (76.2 cm) typical* 30" (76.2 cm) min. NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See “Electrical Requirements” section. A. 2" x 4" wall stud B. Grounded 3 prong outlet 66" (167.6 cm) min.