Lorex L4202 Instruction Manual

Controller (Video Web Server) L4202 FOR MORE INFORMATION WWW.STRATEGICVISTA.COM BEFORE OPERATING THIS SYSTEM, PLEASE READ THIS MANUAL THOROUGHLY AND RETAIN IT FOR FUTURE REFERENCE

an internet based digital video server capable of connecting up to 2 channels of video sources to distribute their compressed live video into Intranet-Internet through Ethernet connection. It also enables DVR series products and cameras to connect to the internet for remote monitoring or remote control. This is a self-contained Web Server so users can access the camera server by browsing the website over the internet using a standard browser, such as Explorer or Netscape, and do all the management, configuration and monitoring easily. The system contains an image compression chipset that is capable of delivering standard JPEG and real-time video into a limited network bandwidth. To learn more about this system or to find out more about our products available, please visit our website at: www.strategicvista.com CAUTION ! RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Explanation of two Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateraltriangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM. “WARNING – TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE” ! -i-

FCC, EMC and LVD. Therefore, it is designed to provide reasonable protection against interference and will not cause interference with other appliance usage. However, it is imperative that user follows this manual's guidelines to avoid improper usage which may result in damage to the unit, electrical shock and fire hazard or injury. In order to improve the feature functions and quality of this product, the specifications are subject to change without notice from time to time. FCC CLASS B NOTICE Note: This equipment has been tested and found to comply with the limits For a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by one or more of the following measures: • Increase the separation between the equipment and the camera and/or monitor. • Connect the equipment into an outlet on a circuit different from that to which the monitor/DVR or cameras are connected. • Consult the dealer or an experienced radio or television technician for help. STRATEGIC VISTA CORP. www.strategicvista.com -ii-

Getting Started Getting Started IP ADDRESS --------------------------------------------------------------------------------------------------------- REAR PANEL --------------------------------------------------------------------------------------------------------- BOTTOM PANEL----------------------------------------------------------------------------------------------------- HARDWARE CONNECTION AT SERVER SITE------------------------------------------------------------- Static IP Setting Static IP Setting SOFTWARE INSTALLATION------------------------------------------------------------------------------------- IP SETTING------------------------------------------------------------------------------------------------------------ Video Web Server SETTING-------------------------------------------------------------------------------------- DVR REMOTE SETTING------------------------------------------------------------------------------------------- PIN CONFIGURATION---------------------------------------------------------------------------------------------- CONNECTING TO A PC VIA THE INTERNET---------------------------------------------------------------- Dynamic IP Setting Dynamic IP Setting WHAT IS A DYNAMIC IP ADDRESS---------------------------------------------------------------------------- SOFTWARE INSTALLATION------------------------------------------------------------------------------------- SYSTEM RESET------------------------------------------------------------------------------------------------------ DDNS REGISTRATION FOR A DYNAMIC IP ADDRESS-------------------------------------------------- CONNECTING THE PC TO A ROUTER / ROUTER LOGIN----------------------------------------------- ROUTER SETTING-------------------------------------------------------------------------------------------------- IP SETTING------------------------------------------------------------------------------------------------------------ VIDEO WEB SERVER SETTING--------------------------------------------------------------------------------- DVR REMOTE SETTING------------------------------------------------------------------------------------------- PIN CONFIGURATION---------------------------------------------------------------------------------------------- CONNECT ALL DEVICES------------------------------------------------------------------------------------------ CONNECTING TO A PC VIA THE INTERNET --------------------------------------------------------------- Operation Guide Operation Guide SOFTWARE OPERATION AT THE REMOTE SITE -------------------------------------------------------- CONTROL PANEL & BASIC OPERATION ------------------------------------------------------------------- PLAYBACK OPERATION ---------------------------------------------------------------------------------------- ADVANCED SETTING -------------------------------------------------------------------------------------------- FAQ’S ------------------------------------------------------------------------------------------------------------------- SPECIFICATIONS ---------------------------------------------------------------------------------------------------- APPENDIX#1 DVR CONTROL ----------------------------------------------------------------------------------- APPENDIX#2 SENDING E-MAIL --------------------------------------------------------------------------------- APPENDIX#3 SOFTWARE DOWNLOAD ---------------------------------------------------------------------- REFERENCE NOTES------------------------------------------------------------------------------------------------ CARE & MAINTENANCE------------------------------------------------------------------------------------------- 1 2 3 3 4 4 5 6 8 9 11 12 13 14 14 14 14 16 19 21 22 24 24 25 25 26 27 28 29 32 33 34 36 37 38 39 -iii-

be read and understood before the product is used. 2. Retain Instructions The safety and operating instructions should be retained for future reference. 3. Heed Warnings All warnings on the product and the instruction manual should be followed. 4. Follow Instructions All operating and use instructions should be followed for optimal performance 5. Cleaning Disconnect this video product from the power supply before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. 7. Water and Moisture Do not use this product near water - for example, near a bathtub, wash bowl, kitchen sink, wet basement, or near a swimming pool. 8. Accessories Use this product only with a stand, tripod, bracket or table recommended by the manufacturer or sold with the product. Any mounting of the product should follow the manufacturer’s instructions. 9. Ventilation This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation, such as a book case or rack, unless proper ventilation is provided or the Manufacturer’s instructions have been adhered to. 10. Power Source This product should be operated from the type of Power source indicated by the marking label. If you are not sure of the type of power supply to your location, consult your product dealer or your local Power company 11. Power Cord Protection Power supply cords should not be routed so that they are likely to be walked on or pinched by items placed on or near them 12. Lightning For added protection, unplug this product from its outlet during a lightning storm. This will prevent damage to the video product due to lightning and power surges 13. Overloading To avoid the risk of fire and electric shock, do not plug this product into an over-loaded power supply. 14. Object and Liquid Entry Never push objects into the openings of this product as they may touch dangerous voltage points that may result in fire or electric shock. Never spill liquid of any kind on this product. 15. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to voltage or other hazards. Refer all servicing to qualified service personnel 16. Damage Requiring Service Disconnect this product from the power supply and refer servicing to qualified service personnel under the following conditions: a. When the power supply cord or plug is damaged b. If objects have fallen into the product c. If the product has been exposed to rain or liquids d. If the product does not operate normally by following the instruction manual. Adjust only the controls that are covered in the instruction manual as an improper adjustment may result in damage and will often require extensive work by a qualified service technician to restore the product to its normal operation e. If the product has been dropped or the cabinet has been damaged f. When the product displays a distinct change in performance - this indicates a need for service 17. Replacement Parts When replacement parts are required, be sure the technician uses replacement parts specified by the manufacturer. Unauthorized substitutions may result in fire, electric shock, or other hazards. 18. Safety Check Upon completion of any service to this product ask the service technician to perform safety checks to determine that the product is in proper working condition. 19. Grounding or Polarization This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin and will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 20. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 21. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 22. Heat The product should be situated away from heat such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. -1-

2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use water damped cloth for cleaning 3. Do not use this unit in very humid and wet places 4. Keep enough space around the unit for ventilation. Slots and openings of the cabinet should not be blocked. 5. During flashes of lightning or cracks of thunder, or when the system is not used for a long time, unplug the system power supply and disconnect the cables to protect the unit from lightening or power surges. Features • Compatible with most CCTV Products. • Empowers all video output devices watching and controlling on the Internet or LAN. • Auto Network Reconnection (ANR). • Support alarm triggers recording & watch dog function. • Support Dynamic IP address via a Router. • Support 4 alarm inputs. • Duplex function, record and playback simultaneously at client site. • Auto e-mail warning system & images uploading function (to FTP site) that will remind you if an external alarm was triggered. • Intelligent non-stoppable recording function after ANR. • Support Multi AP screens and HTTP display (IE browser). • Unique video player. -2-

Owner’s Manual & CD CHECK YOUR PACKAGE TO MAKE SURE THAT YOU RECEIVED THE COMPLETE SYSTEM, INCLUDING THE COMPONENTS SHOWN ABOVE. Power Adapter & Cord GETTING STARTED: Terminal block Crossover LAN cable Before installation, contact your ISP (Internet Service Provider) for your own IP address. Note : The bundled software is compatible with the following Windows operating systems : WIN2000, WIN2003 and WINXP. It is not recommended to use with WIN98 & WIN ME, which may cause system conflictions with the software.

-4- 1. LAN Connect the RJ45 Crossover LAN cable to the internet, or directly to a PC 2. ACT & LINK LED’s When these LED’s are blinking it indicates that the network is in operation 3. VIDEO INPUT (BNC, 2 channels) Connect to a video source, such as a camera or DVR video output. 4. ALARM I/O (optional for advanced applications) Connect control devices, such as a PTZ Camera, DVR, Motion Sensors, external alarm signal inputs, etc 5. POWER Plug in the supplied power adaptor (12V / 500mA). RESET BUTTON (at the bottom of the Video Web Server) Push this button for more than 5 seconds to reset the setting back to the default setting. BOTTOM PANEL : 3 Bottom 1 2 3 4 5

A . Connection Structure NOTE: The RS-485 to control the DVR is optional. 1. Connect the video output of the camera or DVR to the video input of the Video Web Server. 2. Connect the PC to the Video Web Server for IP setting. 3. Connect the Video Server to the ADSL or CABLE MODEM with a Static IP address. 4. Connect PC with Internet and remote control Video Web Server. B . Connection Application

1. Put the attached CD into the CD-ROM. The application program will install on your PC. Note: The CD contains a self-running installation that automatically starts when the CD is inserted. Follow the instructions for installation as indicated in the next few pages. 2. Press “Next”. 3. Choose the destination location and press “Next”.

5. Press “Next” to begin copying the files 6. After the installation, the following files listed below will appear in your assigned path or file folder. There will be 6 files and 1 folder. -7-

1. Using the Crossover LAN cable connect the Video Web Server to the PC. Note : In some operating environments, users might need the standard CAT5 cable. RJ-45 POWER 2. Network setting for the PC. (The instruction is based on Win XP O/S. If your Operating System is Win 2000 or Win 2003, the setup procedure is similar to that of Win XP O/S.) Click twice 3. Click on “Properties” for TCP/IP setup -8-

5. Click on “Use the following IP address” and set the IP address and subnet mask NOTE : 1. Before changing the PC network setting, please write down the original network setting in order to recover the original setting after the setup. 2. The IP address should be 192.168.1.XXX. The setting of “XXX” could be set from 1 to 254 Do not use 10 since 192.168.1.10 is the default IP ); the subnet mask is 255.255.255.0. STEP 3: VIDEO WEB SERVER SETTINGS 1. To configure the Server IP, please click twice to enter the setup. 2. Key in the User Name, Password, and Server IP (The default setting for the User Name is admin and the default Password is admin ; Server IP is 192.168.1.10, Port : 80). Click on OK to connect. -9-

program on the Video Web Server. Click on “System Config” to set up.(NOTE: If you don’t connect a camera or DVR to the Video Web Server, the only thing you will see is the control bar.) SYSTEM CONFIG 4. In the Peripheral setting, set the baud rate, ID and model that you want to remotely control later. Press the “APPLY” to enable the change after the setting. 5. Click on “System Config” again. In the Network setting, set the server IP, gateway, net mask and DNS provided from your local ISP ( internet service provider ). Press “APPLY” to enable the change after the setting. -10-

server. Static IP STEP 4: DVR REMOTE SETTING 1. Connect the DVR and monitor. 2. In the “Remote” setting, set the baud rate and ID the same as the “Peripheral” setting in the Video Web Server. Set the remote mode to RS-485 (see example below). (REMOTE) REMOTE MODE : RS-485 BAUD RATE : 2400 ID : 001 (MENU) TIMER CAMERA RECORD ALARM DWELL REMOTE SYSTEM EVENT A. 1 / 4 CH DVR B. 4 / 9 / 16 CH DMR (MENU) SEARCH TIMER RECORD CAMERA SYSTEM EVENT (SYSTEM) : : REMOTE MODE : RS-485 BAUD RATE : 2400 REMOTE ID : 001 -11-

After the remote setting, connect the DVR, noting the following pins. PIN 1, 6. RS485-A, RS485-B Use RS485-A & RS485-B serial communication signals to control digital units such as a DVR. PIN 4, 7, 8, 9. ALARM INPUT Use PIN 4,7,8,9 to receive the alarm input and then trigger the Video Server to send E- mail to users for the auto e-mail warning system. (Alarm 1, 2 are for CH1; alarm 3, 4 are for CH2) PIN 5. GND Ground PIN 2, 3. NORMAL HIGH, NORMAL LOW Use PIN 2 or 3 to trigger an external device. Please see the example picture below for a 1CH/4CH DVR. RS485-A RS485-B -12-

1. Change the PC network setting to the original setting and link the PC to the internet. 2. Click twice to enter your User name & Password (Note : The default User Name and Password are both “admin”), and the static IP, which you have set for the Video Web Server in step 4.5. Then click OK to connect. -13-

Follow the same procedure as outlined on Page 6 & 7 for the Static IP Setting STEP 2: SYSTEM RESET: Before using the Video Web Server, please connect the power to the Video Web Server and push the button under the unit for more than 5 seconds to reset the setting. See the photo below STEP 3: DDNS REGISTRATION FOR A DYNAMIC IP ADDRESS: A Dynamic IP Address is an IP (Internet Protocol) address that changes each time you connect to the internet. This cuts down on the number of IIP addresses large consumer providers need because not all of their customers are using the service at any given time. It also cuts down on bandwidth usage by preventing consumers from hosting servers. Note: a number of companies have started to offer services aimed at updating DNS for dynamically connected clients. WHAT IS A DYNAMIC IP ADDRESS ? 1. You must have a gateway router that supports DDNS (Dynamic Domain Network Service). Please go to www.dlink.com or www.linksys.com for a list of available routers 2. To register for a dynamic IP address click on the free site “http://www.dyndns.org” and click on “Account” (please look at the example below). -14-

3. Register your information (Username, E-mail address & password). Click on “Create Account” when the necessary information is completed 4. After registering your account, you will receive an e-mail, which contains instructions to activate your account. If you do not follow these directions within 48 hours, you will need to re-register your account. 5. Login your account. -15-

7. Users can set up their own DDNS HOST. For example, the user’s Host name is “avtech.dyndns.org”. Click on “Add Host” to finish the setting. (NOTE : Some routers don’t support some DDNS HOSTs) STEP 4: CONNECTING THE PC TO A ROUTER / ROUTER LOGIN: NOTE : The following settings are different from router to router. Please read the instructions on your router thoroughly. 1. Connect the PC to the router using the LAN cable(LAN end) POWER -16-

2000 or Win 2003, the setup procedure is similar to that of Win XP O/S.) 3. Click on “Properties” for TCP/IP setup Click twice -17-

5. Choose “Obtain an IP address automatically” 6. Enter the “Command Prompt” -18-

log in to the router from the Internet Explorer. Enter the login web page and key in the router’s user name and password. 7. In the setting window, enter “ ipconfig” , and write down the router’s gateway(e.g. 192.168.1.1) NOTE : In the router setting, there are four steps to follow. 1. Dial setting 2. DHCP setting 3. Virtual server setting 4. DDNS setting STEP 5: ROUTER SETTING -19-

1. Click on “INTERNET PORT” and choose your WAN type (e.g. PPPoE). Enter your “User Name” and “Password” to dial up the dynamic IP address. Press save after you set up. 2. Press “LOCAL PORT” and set “Start IP address” and “Number of IP address”. (For example, if the IP address of your Video Web Server is 192.168.1.10, then 10 is excluded from the setting range) Press save after you finish setting up. 3. In the “ADVANCED SETUP / Virtual Server”. Choose “By Port” and set the “Port Number” to 80 for the Video Web Server. Set the “Local Server IP Address” to 192.168.1.10. (The default Video Web Server IP and port). Press add & save after you set up. -20-

Name” and “Password” that you applied in step 3. Press save after you set up. 1. Connect the PC or Notebook to the Video Web Server using the crossover LAN cable. Note: In some operating environments, users might need the standard CAT5 cable. RJ-45 POWER (MENU) TIMER CAMERA RECORD ALARM DWELL PIP MOTION DISPLAY NETWORK USER SYSTEM EVENT PTZ In the DVR Menu, select “Network” (NETWORK) IP ADDRESS 061.066.138.074 NET MASK 255.255.255.000 GATEWAY 061.066.138.073 DNS 168.095.001.001 PORT 00080 RESET DEFAULT NO The following 5 network settings should be entered. (please see the example) STEP 6 : IP SETTING -21-

2. Key in the User Name, Password, and IP address (The default setting for the User Name and Password are both “admin”; IP address is 192.168.1.10, Port : 80). Click OK to connect. 2. Network setting for PC. (The instruction is based on Win XP O/S. If your O/S is Win 2000 or Win 2003, the setup procedure is similar to that on Win XP O/S.) Click twice STEP 7: VIDEO WEB SERVER SETTING -22-

Video Web Server. Click on “System Config” to set up. SYSTEM CONFIG 5. Click on “System Config” again. In the Network setting, set the gateway the same as the router’s gateway(192.168.1.1). Press “APPLY” to enable the change after the setting. 4. In the Peripheral setting, set baud rate, ID and the model that want to remotely control later. Press “APPLY” to enable the change after the setting. -23-

2. In the “Remote” setting, set the baud rate and ID the same as the “Peripheral” setting on the video web server. Set the remote mode to RS-485.(see example below) (REMOTE) REMOTE MODE : RS-485 BAUD RATE : 2400 ID : 001 (MENU) TIMER CAMERA RECORD ALARM DWELL REMOTE SYSTEM EVENT A. 1 / 4 CH DVR B. 4 / 9 / 16 CH DMR (MENU) SEARCH TIMER RECORD CAMERA SYSTEM EVENT (SYSTEM) : : REMOTE MODE : RS-485 BAUD RATE : 2400 REMOTE ID : 001 After the remote setting, connect the DVR, noting the following pins below PIN 1, 6. RS485-A, RS485-B Use the RS485-A & RS485-B serial communication signals to control digital units, such as a DVR. PIN 4, 7, 8, 9. ALARM INPUT Use the PIN 4,7,8,9 to receive the alarm input and trigger the Video Server to send mail to users for the auto e-mail warning system. (Alarm1, 2 are for CH1; alarm3, 4 are for CH2) STEP 8: DVR REMOTE SETTING STEP 9: PIN CONFIGURATIONS A normally open contact/sensor can be connected to Pin 4 ,5.7,8 & 9, where Pin 5 is Nomally open (Ground) and Pin 4,7,8 & 9 are Common (Alarm Input 1-4) -24-

DVR ADSL modem (WAN end) 2. Click twice and enter your User name, Password and host on the Video Web Server. (Note : If you did not change the “Account” , the User Name and Password are both “admin”). Click OK to connect. DDNS HOST RS485-A RS485-B 1CH/4CH DVR. Video Web Server STEP 10: CONNECTING ALL DEVICES 1. Change PC network setting to the original setting and link PC to the internet. STEP 11: CONNECTING TO A PC VIA THE INTERNET -25- PIN 5. GND Ground PIN 2, 3. NORMAL HIGH, NORMAL LOW Use PIN 2 or 3 to trigger an external device

twice to enter the Login setup (please refer to “software installation”) Step 2: Key in “User Name” and “ Password”. (e.g. “User Name” and “Password” is “dan”, and the IP address is 61.222.50.174). Click “OK” to establish the connection. Follow the steps below to connect to a remote site. (e.g. If you set up the server at your office with one static ADSL, you can remotely watch the video anywhere, with a networkable computer.) Step 3: If you see the video screen, then you have successfully connecting to the server. NOTE: 1.There are two ways to get the software, one is via the attached CD, the other is via the Video Web Server. (Refer to APPENDIX#3) 2.You can press the “Address Book” button to add a new IP into this table or choose any login IP address to access the Video Server. 3.This function is designed to store a list of IP addresses which you can control and manage. SOFTWARE OPERATION AT THE REMOTE SITE -26-

1. Image transmission rate per second 2. Video Channels 3. Data transmission rate 4. Connection/Disconnection 5. Resolution : VGA QVGA 6. Image quality : High Middle Low 7. Image adjusting : Brightness/ Contrast/ Saturation 8. IP address (last 3 digits are displayed) 9. Snapshot : Press this button to automatically save the image on your PC. 10. Record : Press this button to record the files & save them on your PC 11. System setting 12. Number of online users 13. Window adjust ( right click for Full Screen) 14. Click on the arrow key to go to the “Digital Device Control Panel”. NOTES 1.When you setup the video input from the DVR, the screen will show the operation interface, shown above. 2.Use the 16 CH DVR to explain the operation (please refer to the DVR user manual & APPENDIX#1 for details) 3.After you press the record icon, there will be a recorded file on your PC. Each recording file can save up to 6000 frames. The recording file will be assigned to the second file if it is more than 6000 frames. If the HDD space is less than 200MB, the program will stop recording. 1. Camera video inputs 2. Quad screen, 7-9-10-13-16 screen 3. Zoom, PIP, Select, Lock, Search, Enter 4. Stop, Record, Rewind, Fast Forward, Pause, Slow, Play 5. Menu(Exit), Left, Right, Up, Down 6. Click on the arrow key to go to the “Video Web Server Control Panel” A. Video Web Server control panel B. Digital device control panel 1 2 3 4 5 1 2 3 4 9 6 7 5 8 10 11 12 13 14 6 -27-

1. On Screen Display 2. Snapshot 3. Stop 4. Pause 5. Slow (1/2, 1/4, 1/8) 6. PLAY 7. Fast 8. OSD show / hide 9. System setting (Path of snapshot, text color, progress color, channel color) 10. Back Video 11. Next Video 12. Playback controlling bar 1 2 3 4 5 6 7 8 9 10 11 12 PLAYBACK OPERATION -28-

1. You can get all the information, Server IP, Gateway, Net Mask & DNS, from your ISP company. 2. Web Port : You can control the Video Web server via this port. 3. Mac : The equipment’s physical address. 4. IP Type : This unit only supports Static IP address, if you want to use Dynamic IP, please obtain through a Router. To set up the network setting of the Video Web Server, check with your network administrator or Internet Service Provider. NOTE : Apply-- After all setting changes, press “apply” to refresh the data in the Video Web Server. Reboot-- Press this button to restart the Video Web Server. SYSTEM CONFIG 1. You can get all the data from the ISP company or by mailing to the server supplier.(POP3/SMTP server) 2. You should set the mail list which you want to send to when the alarm is triggered. 3. If it is not necessary for you to verify password and user’s name, please choose Verify as “No”. 4. Please refer to appendix#2 for more details. When the alarm is triggered, the Video Web Server will capture the instant picture and e-mail the captured image to the assigned recipients. NETWORK NETWORK MAIL MAIL ADVANCED SETTINGS -29-

department. 2. The default uploading port is No.21. 3. You can set the uploading directory by yourself. When the alarm is triggered, the video server will capture the instant picture and upload the captured image to the assigned FTP site. 1. User’s level: SUPERVISOR - controls all the functions USER LEVEL - control advanced functions GUEST LEVEL - control basic functions only 2. Live time : During this time period, users are allowed to control the Video Web Server. Set up the user’s account, password (Max 5 accounts) and authority. Peripheral Control : Set up the video input device. You can select the devices and set up “Baud Rate & ID No.” to control the equipment via the Video Web Server. You can set up all the peripheral setting in this Windows. (Refer to APPENDIX#1 for more details) FTP FTP ACCOUNT ACCOUNT PERIPHERAL PERIPHERAL -30-

recording file and snapshot images . 1. Firmware Version : For the current firmware version, you can click on the “Find” button to get the latest firmware from your PC. Press “Upgrade Firmware” to upgrade it. 2.Turbo step: You can set the turbo step when the turbo function is open. Upgrade the firmware. NOTE : Do not reboot the Video Web Server while it is upgrading the firmware. 1. Alarm : Enable or disable Alarm trigger function. 2. Method : Two selections—Email or FTP. 3. Resolution : Image storing resolution for Email or FTP function. 4. Alarm Duration : Alarm duration time. 5. Post Image : You can select how many images you need to store when the alarm is triggered. 6. Alarm record : Enable or disable “Alarm trigger recording” function. 7. Alarm refresh : Clean the alarm message “ ” which is shown on the screen. Set up the ALARM function. You can use it to operate the “alarm trigger recording” function. FILE PATH FILE PATH TOOLBOX TOOLBOX ALARM ALARM -31-

remote PC without connecting it to the Internet ? ANS: Yes, you can connect the Video server with remote PC using the Crossover cable directly. 2. If I do not have any network in my office or house, could I use this system? ANS: Yes, you could use this unit. You can connect the Video Server with PC or notebook directly, and take the PC as a storage device. Save all video from your cameras and display the Video record on the PC. 3. Can I use ISDN to connect the Video Server? ANS: Our Video Server could be connected via ADSL or CABLE modem. It does not support ISDN connection. However, if you have a router which supports ISDN, RJ-45 and port forwarding function, it can be used with our Video Server. 4. What kind of frame rate are we expecting? ANS: The frame rate = band width(Kbps) / 8 / image size(Kbytes)-->Daytime QVGA(Low-6 Kbytes, Middle-9 Kbytes, High-12 Kbytes), VGA(Low-24 Kbytes, Middle-36 Kbytes, High-48 Kbytes). ONLINE USER ONLINE USER 1. Info refresh : Refresh the online users’ information Get online user’s information FAQ’S -32-

Bytes SDRAM Hardware One RJ-45 for 10/100 Mbps Ethernet, LED to indicate Link/ Actual Status Yes RS-485 Port 12V / 500mA Power Password Protection Security Assign IP address Installation Triggered by GPIO Input, Action: E-mail images or images uploading to the FTP sites specific account Trigger & Action 64K Min. Bandwidth Up to 15/frames per second, 7.5 FPS/channel Performance VGA: 640 x 480, QVGA: 32 0x 240 Resolution 10 Max. # of user accounts 6 Max. # of remote accesses GPIO with triggers for E-mail or FTP site TCP/IP, ICMP, FTP, HTTP Protocols Brightness, Contrast, Saturation, Quality level adjustment Video Adjustment JPEG Image Compression Ethernet (10/100 Base-T) Network Interface Yes (this function keeps the Video Web Server working, and not shut down) Watch Dog 4 inputs Alarm Input 2 channels for analog and digital products, 1.0V p-p, Composite BNC Video Input Because our products are subject to continuous improvement, SVII and its subsidiaries reserve the right to modify product design and specifications without notice and without incurring any obligation. E&OE -33-

ALARM INPUT 1 ALARM INPUT 3 NORMAL LOW ALARM INPUT 4 NORMAL HIGH RS485-B RS485-A EXTERNAL ALARM NO EXTERNAL ALARM COM RS485-A RS485-B RS232-TX RS232-RX ALARM INPUT 3 ALARM INPUT 4 GND ALARM INPUT 2 ALARM INPUT 1 PIN CONFIGURATIONS FOR CONNECTION TO A 1CH DVR PIN CONFIGURATIONS FOR CONNECTION TO 4CH, 9CH & 16CH DMR Web Server DMR DVR Web Server GND ALARM INPUT2 ALARM INPUT1 ALARM INPUT3 NORMAL LOW ALARM INPUT4 NORMAL HIGH RS485-B RS485-A RS232-TX GND RS232-RX RS485-B VIDEO LOSS RS485-A SWITCH OUT DISK FULL ERROR OUT ALARM RESET REC STAR ALARM INPUT EXTERNAL ALARM NC EXTERNAL ALARM COM EXTERNAL ALARM NO APPENDIX #1 – DVR CONTROL -34-

NOTE : Remote mode : RS-485, Baud rate : selectable, ID : same as “Peripheral Control” in the Video Web Server. A. 1 / 4 CH DVR B. 4 / 9 / 16 CH DMR 3) Set the “Peripheral Control” in the system configuration of the Video Web Server. (MENU) TIMER CAMERA RECORD ALARM DWELL REMOTE SYSTEM EVENT (REMOTE) REMOTE MODE:RS-485 BAUD RATE:selectable ID:020 (MENU) SEARCH TIMER RECORD CAMERA SYSTEM EVENT (SYSTEM) : : REMOTE MODE:RS-485 BAUD RATE:selectable REMOTE ID:021 -35-

Sensor. 2) Set the “Mail setting” item in the system configure. NOTE 1 : You can get all the data from the ISP ( Internet Service Provider) company or by mailing to the server supplier (POP3/SMTP server). NOTE 2 : You should set the mail list when the alarm is triggered. NOTE 3 : When the alarm is triggered, you can find “ ” message showed on the screen. The AP will start recording automatically and you can get the email with the snapshot image in your mailbox. APPENDIX #2 – SENDING E-MAIL -36- Please connect the N.O. end of sensor to ground (GND 5) and connect the COM. end of the sensor to input end (4,7,8,9) Video Web Server

“Setup.exe” in the HDD. Step 1 : Please connect the PC to the Internet and key in the Video Web Server’s IP address (ex : 61.222.50.160) in the browser. Then press ENTER. Step 3 : Click on “Setup.exe” twice to install the application program. Step 4 Click on twice to enter the Login setup and refer to “software installation” for other operations. APPENDIX #3 – SOFTWARE DOWNLOAD -37-

setting of “XXX” could be set from 1 to 254, where 10 is excluded (The default IP is 192.168.1.10 ) 2. In step 4.4 : Please make sure that the Peripheral setting is the same as the setting on the DVR, which you want to remotely control later. 3. In step 6.2 : The Server IP is the IP you set in step 4.5. Dynamic IP 1. In step 3.7 : Some routers don’t support the DDNS HOST. 2. In step 4.1 : Please use the router’s LAN end to connect to the PC. 3. In step 4.8 : Please use the IE(Internet Explorer) browser to enter the router’s gateway. 4. In steps 5.1- 5.4 : Please make sure that you press “save’ after you finish the setting. 5. In step 7.4 : Please make sure that the Peripheral setting is the same as the setting on the DVR, which you want to remotely control later. 6. In step 10 : Please use the router’s LAN end to connect the Video Web Server. Use the WAN end to connect to the ADSL modem. 7. In step 11.2 : The Server IP is the DDNS HOST, which you set in step 5.4. REFEFENCE NOTES : -38- Important Note: You must have a gateway router that supports DDNS (Dynamic Domain Network Service). Please go to www.dlink.com or www.linksys.com for a list of available routers

Please follow these instructions to ensure proper care and maintenance of this system Keep your monitor and camera dry. If it gets wet, wipe it dry immediately. Use and store your unit in normal temperature environment. Extreme temperatures can shorten the life of the electronic devices. Handle the monitor carefully. Dropping it can cause serious damage to the unit. Occasionally clean the unit with a damp cloth to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the unit. Keep the unit away from excessive dirt and dust. It can cause premature wear of parts. -39-