Metra Electronics 99-8218 Installation Instructions Manual

Phillips Screwdriver • Socket 1-800-221-0932 www.metraonline.com KIT FEATURES © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION • DIN Radio Provision with Pocket • ISO Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Units Provision 99-8218 APPLICATIONS A) Radio Housing • B) Radio Housing Brackets • C) ISO Snap-In Brackets • D) Double DIN Brackets KIT COMPONENTS C E) Trim Plate • F) Double DIN Trim Plate • G) Pocket • H) (4) # 8 x 3/8 Phillips Screws • I) (4) #4 x 1/4 Phillips Screws B D E F G H I Small Flat Blade Screwdriver or Panel Removal Tool TOYOTA CAMRY / CAMRY HYBRID 2007-2011 A WIRING AND ANTENNA CONNECTIONS (Sold Separately) Wire harness: • 70-1761 Toyota 1987-up • TYTO-01 Toyota amp interface harness 2003-up Antenna adapter: • Not required TOOLS REQUIRED:

Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . 3 - ISO Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . 4 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 TABLE OF CONTENTS 99-8218 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Disconnect the negative battery terminal to prevent an accidental short circuit. Turn the shift knob counterclockwise to remove. 1 2 Unclip and remove (1) trim panel from each side of the pocket below the radio/climate control assembly. (2 panels total) (Figure A) 3 Unclip and remove the top of the center console including the cup holders. (Figure B) 5 1 2 3 4 5 6 A 1 2 3 4 5 6 B 1 2 3 4 5 6 C Continued on Page 2. Unclip and remove the shift knob trim panel. (Figure B) 4 Remove (1) Phillips screw from each side of pocket below the radio/climate control assembly (2 screws total). (Figure C) 6 Unclip and remove the pocket. (Figure C) 7

the brackets to the radio/climate control assembly and separate the radio from the climate controls. (Retain climate controls and screws for use during kit assembly). (Figure C) 1 2 3 4 5 6 A 1 2 3 4 5 6 B C Unclip and remove the A/C vents above the radio. (Take care not to scratch the dash panel. (Figure A) 11 Remove (2) 10mm bolts above the radio (behind the A/C vents) and (2) 10mm bolts below the climate controls (behind pocket) then unplug and remove the radio/climate control assembly. (Figure B) Unscrew and remove the (2) Clips from the back of the factory radio. (Retain clips for use during kit assembly. (Figure C) Continue to kit assemby. TOYOTA CAMRY / CAMRY HYBRID 2007-2011

B C A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the after-market radio into the cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure B) NOTE: Refer also to the instructions included with the aftermarket radio. Continue to Final Assembly. 4 Align the small legs on the bottom of the radio housing with the slots in the top of the climate control. Then slide the climate control sideways to engage together. (Figure C) 5 Attach the radio housing brackets to the radio housing using the included Phillips screws. (Figure D) D 6 Secure the radio housing brackets to the climate control using the factory hardware. (Figure D) 7 Attach the (2) clips removed in step 11 in dash disassembly to the radio housing brackets using the supplied small Phillips screws.(Figure D)

radio with the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio open- ing until the side clips engage. (Figure B) 4 Snap the pocket into the radio housing. (Figure B) NOTE: Refer also to the instructions included with the aftermarket radio. Continue to Final Assembly. 5 Align the small legs on the bottom of the radio housing with the slots in the top of the climate control. Then slide the climate control sideways to engage together. (Figure C) 6 Attach the radio housing brackets to the radio housing using the included Phillips screws. (Figure D) D 7 Secure the radio housing brackets to the climate control using the factory hardware. (Figure D) 8 Attach the (2) clips removed in step 11 in dash disassembly to the radio housing brackets using the supplied small Phillips screws.(Figure D) ISO RADIO PROVISION WITH POCKET 3 Snap the Trim plate into the Radio Housing. (Figure B)

from radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Double DIN radio into the Double DIN bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure C) NOTE: Refer also to the instructions included with the aftermarket radio. Continue to Final Assembly. 4 Snap the Double DIN trim-plate into the housing/radio assembly. (Figure C) 5 Align the small legs on the bottom of the radio housing with the slots in the top of the climate control then slide the climate control sideways to engage together. (Figure D) D 6 Attach the corresponding radio housing bracket to the radio housing using the included Phillips screws. (Figure E) 8 Attach the (2) clips removed in step 11 in dash disassembly to the radio housing brackets using the supplied small Phillips screws.(Figure E) DOUBLE DIN 7 Secure the radio housing brackets to the climate control using the factory hardware. (Figure E) RADIO PROVISION E

from radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Stacked ISO units into the Double DIN bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the units. (Figure C) NOTE: Refer also to the instructions included with the aftermarket radio. Continue to Final Assembly. 4 Snap the Double DIN trim-plate into the housing/radio assembly. (Figure C) 5 Align the small legs on the bottom of the radio housing with the slots in the top of the climate control then slide the climate control sideways to engage together. (Figure D) D 6 Attach the corresponding radio housing bracket to the radio housing using the included Phillips screws. (Figure E) 8 Attach the (2) clips removed in step 11 in dash disassembly to the radio housing brackets using the supplied small Phillips screws.(Figure E) STACKED ISO 7 Secure the radio housing brackets to the climate control using the factory hardware. (Figure E) UNITS PROVISION E

proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly. A A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape B C D Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. 12V Ignition / Acc . . . Red 12V Batt / Memory . . Yellow Ground . . . . . . . . . . . Black* Power Antenna . . . . . Blue Amp Turn-On . . . . . . Blue / White Amp Ground . . . . . . . Black / White Illumination. . . . . . . . Orange Dimmer . . . . . . . . . . Orange / White Right Front (+) . . . . . White Left Front (-). . . . . . . White / Black Right Rear (+). . . . . . Violet Right Rear (-) . . . . . . Violet / Black Left Rear (+). . . . . . . Green Left Rear (-) . . . . . . . Green / Black *NOTE: When Black a wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications. METRA / EIA WIRING CODE FINAL WIRING CONNECTIONS