Metra Electronics 95-7324 Installation Instructions Manual

95-7324 APPLICATIONS KIA Optima 2006.5-2010 KIT FEATURES • Double DIN radio provision • Stacked ISO units provision A) Double DIN Trim Plate • B) Double DIN Brackets KIT COMPONENTS A B TOOLS REQUIRED: Phillips Screwdriver • Small Flat Blade Screwdriver/ Panel Removal Tool 1-800-221-0932 © COPYRIGHT 2004-10 METRA ELECTRONICS CORPORATION www.metraonline.com WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • 70-1004 - Hyundai 2006-up/KIA harness 2004-up • 70-7303 - Hyundai / KIA Harness 2009 Antenna Adapter: • 40-KI11 - 2009-10 Kia Optima

Kit Assembly * - Double DIN Radio Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Stacked ISO Units Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TABLE OF CONTENTS 95-7324 *Note: Refer also to the instructions included with the aftermarket radio.

KIA OPTIMA 2006.5-2010 PUSH A/C PUSH TEMP FM AM 4RPT POWER VOLUME SEEK TRACK 103.9 1 2 3 2 FF REW 5 RDM A 103.5 FM 3:05 EQ CD FM AM SCAN AUDIO POWER VOLUME TUNE SEEK TRACK RPT RDM FF REW 1 4 2 5 3 6 B 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 1 Unclip and remove the panel sur- rounding the radio including the a/c vents and climate controls. (Figure A) 2 Remove (4) Phillips screws securing radio. Unplug and remove radio. (Figure B) 3 Continue to kit assembly.

2 A B DOUBLE DIN RADIO PROVISION Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Figure A) 1 Slide the Double DIN radio into the bracket/trim plate assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure B) 2 Continue to final assembly. *Note: Refer also to the instructions included with the aftermarket radio.

3 A B STACKED ISO UNITS PROVISION Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Figure A) 1 Slide the stacked ISO units into the bracket/radio housing assembly and secure the units to the kit using the screws supplied with the units. (Figure B) 2 Continue to final assembly. *Note: Refer also to the instructions included with the aftermarket radio.

FINAL ASSEMBLY (A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape A B C D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. 1 2 3 FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METRA / EIA WIRING CODE 12V Ignition / Acc. . . . . . . . . . Red 12V Batt / Memory. . . . . . . . . Yellow Ground. . . . . . . . . . . . . . . . . . Black* Power Antenna. . . . . . . . . . . . Blue Amp Turn-On . . . . . . . . . . . . . Blue / White Amp Ground. . . . . . . . . . . . . . Black / White Illumination . . . . . . . . . . . . . . Orange Dimmer . . . . . . . . . . . . . . . . . Orange / White Right Front (+) . . . . . . . . . . . . Gray Right Front (-). . . . . . . . . . . . . Gray/ Black Left Front (+) . . . . . . . . . . . . . White Left Front (-). . . . . . . . . . . . . . White / Black Right Rear (+) . . . . . . . . . . . . Violet Right Rear (-) . . . . . . . . . . . . . Violet / Black Left Rear (+) . . . . . . . . . . . . . Green Left Rear (-) . . . . . . . . . . . . . . Green / Black *NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications. 4

www.metraonline.com