Metra Electronics 99-7011 Installation Instructions Manual

99-7011 MITSUBISHI Lancer 2008-2010 KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision • Painted to Match Factory •A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Snap in Pocket KIT COMPONENTS A Phillips Screwdriver/ Panel Removal Tool • Cutting Tool 1-800-221-0932 www.metraonline.com B D E C F TOOLS REQUIRED: APPLICATIONS © COPYRIGHT 2008-2009 METRA ELECTRONICS CORPORATION WIRING AND ANTENNA CONNECTIONS: (Sold Separately) Harness: • MITO-02 - Mitsubishi amp interface harness 2007-up • 70-7005 - Mitsubishi harness 2007-up Antenna Adapter: • No antenna adapter required

Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5 - Double DIN Radio Provision/Stacked ISO Mount Units Provision . . . . . . 6 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 TABLE OF CONTENTS 99-7011 Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

99-7011 DASH DISASSEMBLY Disconnect the negative battery ter- minal to prevent an accidental short circuit. 1 Open the glove box and remove (1) Phillips screw from the panel to the right of the glove box door. Unclip and remove the panel. (Figure A) Remove (1) Phillips screw from the panel above the glove box then unclip and remove the panel. (Figure B) Continued on page 2. 2 B A

99-7011 DASH DISASSEMBLY 4 Unclip the radio switch panel includ- ing the hazard switch assembly. Unplug hazard switch assembly and remove panel. (Figure C) 5 Remove (4) Phillips screws secur- ing the radio chassis. Unplug and remove chassis. 7 Unclip assembly, unplug ribbon cable from assembly and remove assembly from the factory radio panel. Retain screws and hazard switch assembly for re-use during kit preparation. 6 Remove (3) Phillips screws securing the hazard switch assembly to the factory radio switch panel. Unclip and remove the switch. (Figure D) 8 Unclip and remove the a/c vents from the factory radio switch panel. (Retain a/c vents for re-use during kit preparation) 9 Remove and retain (7) factory clips from rear of radio housing for re-use during kit preparation. Continue to kit preparation. PASSENGER AIRBAG OFF PASSENGER PASSENGER AIRBAG OFF PASSENGER D C

Secure the hazard switch assembly into the radio housing using the factory hard- ware. Snap the a/c vents into the radio housing. (Figure A) Use the (7) plastic factory clips previously removed during dash disassembly and attach where shown. (Figure B) 1 2 PASSENGER PASSENGER AIRBAG OFF A REAR VIEW OF RADIO HOUSING B MITSUBISHI LANCER 2008-2010 Continue to kit assembly

4 A B C DIN RADIO PROVISION WITH POCKET Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 1 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 2 Snap the pocket into the radio hous- ing. (Figure C) 3 Continue to final assembly. *Note: Refer also to the instructions included with the aftermarket radio.

5 A B C ISO MOUNT RADIO PROVISION WITH POCKET Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 1 Slide the radio into the radio housing until it snaps into place. (Figure B) 2 Snap the trim plate onto the front of the radio housing. (Figure B) 3 Snap the Pocket into the radio housing. (Figure C) 4 Continue to final assembly. *Note: Refer also to the instructions included with the aftermarket radio.

6 DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNITS PROVISION Cut and remove the center bar from the radio housing. (Figure A) 1 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 2 Slide the Double DIN or stacked ISO mount unit(s) into the bracket/radio housing assembly and secure the unit(s) to the assembly using the screws supplied with the unit(s). (Figure C) 3 Continue to final assembly. *Note: Refer also to the instructions included with the aftermarket radio. A B C Snap the Double DIN trim plate onto the front of the radio housing. (Figure C) 4

FINAL ASSEMBLY (A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape A B C D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. 1 2 3 FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METRA / EIA WIRING CODE 12V Ignition / Acc. . . . . . . . . . Red 12V Batt / Memory. . . . . . . . . Yellow Ground. . . . . . . . . . . . . . . . . . Black* Power Antenna. . . . . . . . . . . . Blue Amp Turn-On . . . . . . . . . . . . . Blue / White Amp Ground. . . . . . . . . . . . . . Black / White Illumination . . . . . . . . . . . . . . Orange Dimmer . . . . . . . . . . . . . . . . . Orange / White Right Front (+) . . . . . . . . . . . . Gray Right Front (-). . . . . . . . . . . . . Gray/ Black Left Front (+) . . . . . . . . . . . . . White Left Front (-). . . . . . . . . . . . . . White / Black Right Rear (+) . . . . . . . . . . . . Violet Right Rear (-) . . . . . . . . . . . . . Violet / Black Left Rear (+) . . . . . . . . . . . . . Green Left Rear (-) . . . . . . . . . . . . . . Green / Black *NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications. 7

www.metraonline.com