Samsung BN68-02618A-00 Quick Setup Manual

Select Language of the OSD. Menu Language : Plug & Play English Español Français Quick Setup Guide Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly. 1-800-SAMSUNG (1-800-726-7864) Samsung Electronics America, Inc. 105 Challenger Road Ridgefield Park, NJ 07660-0511 Samsung Electronics Canada Inc. 55 Standish Court Mississauga, Ontario L5R 4B2 Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST. To register this product, visit: www.samsung.com/ register. STOP Please do not return this unit. If you have problems operating your TV, call: 1-800-SAMSUNG (1-800-726-7864) For web support please visit: www.samsung.com/support Step 1: Install the Stand Follow the steps below to connect the TV to the stand. (50 inch model only) ✎ ✎NOTE xx Make sure to distinguish between the front and back of the Stand and Guide Stand when assembling them. xx Make sure that at least two persons lift and move the PDP TV. xx Stand the product up and fasten the screws. If you fasten the screws with the PDP TV placed down, it may lean to one side. 1 Connect the Guide Stand to the Stand using five screws (M4 X L12) as shown. 2 With your TV upright, connect the TV to the Stand. 3 Fasten two screws (M4 X L12) at position 1, and then fasten three screws (M4 X L12) at position 2. s s s s s s Rear Screws (M4 X L12) 1 s s s s s 2 Step 2: Install the Batteries into the Remote To install batteries into your remote control, follow these steps: 1. Lift the cover on the back of the remote upward as shown in the figure to the right. 2. Install two AAA batteries. ✎ ✎Make sure to match the + and - ends of the batteries to the diagram in the battery compartment. 3. Replace the cover. Step 3: Connect Power and Antenna or Cable Step 4: Connect External Devices Connecting an AV device (DVD/Blu-ray player, cable/satellite box Step 5: Run Plug & Play When you turn on your TV for the first time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV’s channel memorizing process. It also displays connection instructions similar to those in this guide. To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow buttons on your remote. To make a selection, press the ENTERE button. To skip a screen, press the MENU button. To turn on your TV, press the POWER button on the remote or on the TV. To run Plug & Play, follow these steps: 1 Using your remote control, select the language for the On Screen Display (OSD), and then press the ENTERE button. 2 Select Home Use, and then press the ENTERE button. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes. 3 Select Antenna Source and Channel Source. If Antenna Source is Cable or Auto, you must select Channel Source to same type as your cable system type. After selecting source, select Search; then press the ENTERE button on your remote. ✎ ✎Most cable systems are Standard (STD) systems, If you are not sure about what kind of cable system you have, contact your cable company. ✎ ✎If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4, according to the directions for your cable or satellite box. 4 The TV memorizes the available channels. This process can take up to 45 minutes. 5 After the TV has memorized the channels, choose the Clock Mode. Select Auto if you have a digital channel in your area. Select Manual if you don’t, or if you have a cable or satellite box. When done, press the ENTERE button. ✎ ✎If you select Manual, the clock setting screen appears. s s s s s Top view Rear Front Rear Guide Stand Screws (M4 X L12) Stand VHF/UHF Antenna Connect Ant In to • Wall cable jack • VHF/UHF Antenna • Cable or Satellite box Ant or Cable Out Use a 75 ohm (round) cable. or Antenna Cable (Not Supplied) AUDIO OUT VIDEO OUT Lowest Quality Connection Audio/Video connection (480i only) Using an Audio/Video Cable DVD, Blu-ray player, cable box, STB satellite receiver, VCR Device Audio Cable (Not Supplied) Video Cable (Not Supplied) Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality. ✎ ✎When connecting to AV IN 1 on the back of your TV, attach the video cable (yellow) to the green jack next to the AV IN 1 label. The jack will not match the color of the video cable (yellow).

Remote Control Buttons and Functions ✎ ✎This is a special remote control for the visually impaired and has Braille points on the Power, Channel and Volume buttons. Viewing the On Screen Menus To view the On Screen Menus, follow these steps: 1. Turn on your TV, press the MENU button on your remote. The main menu appears. The menu’s left side has the following menu options: Picture, Sound, Channel, Setup, Input, Application, and Support. 2. Press the ▲ or ▼ button on your remote to select a menu option, and then press the ENTERE button. 3. When done using the menu, press the EXIT button on your remote to exit. Selecting a Source To watch a movie on your Blu-ray player or watch your favorite TV show, you must select the correct source. A source is a device, such as a Blu-ray/DVD player, a cable/satellite box, antenna or a cable TV input. Sources can be connected to your TV through the HDMI, DVI, Component, Composite, or D-sub connections, or through the Antenna or Cable In connections. To view the signal from a source connected to the HDMI, DVI, Component, Composite, or D-sub jack, press the SOURCE button on your remote. Each time you press the SOURCE button, you change to a different source. CH LIST MUTE POWER SOURCE ON/OFF PRE-CH @TV INTERNET MENU CONTENT TOOLS INFO CH LIST MUTE POWER SOURCE ON/OFF PRE-CH @TV INTERNET MENU CONTENT TOOLS RETURN MEDIA.P FAV.CH P.SIZE CC A B C D MTS EXIT INFO Changing Channels and Adjusting the Volume Adjust the volume by pressing the Volume button on the remote. CH LIST MUTE POWER SOURCE ON/OFF PRE-CH @TV INTERNET MENU CONTENT TOOLS RETURN MEDIA.P FAV.CH P.SIZE CC A B C D MTS EXIT INFO Change the channels by pressing the Channel button on the remote. ✎ ✎If your TV is attached to a cable or satellite box, change the channel using the box’s remote. ✎ ✎You can also change the channels by pressing the z button on the front panel of your TV and adjust the volume by pressing the y button. CH LIST MUTE POWER SOURCE ON/OFF PRE-CH @TV INTERNET MENU CONTENT TOOLS RETURN MEDIA.P YAHOO! FAV.CH P.SIZE CC A B C D 3D EXIT INFO Turns the TV on and off. Returns to the previous channel. Cuts off the sound temporarily. Changes channels. Turns the remote control light on or off. When on, the buttons become illuminated for a moment when pressed. (Using the remote control with this button set to ON will reduce the battery usage time.) Link to various internet services. Displays the channel list on the screen. Displays information on the TV screen. Selects the on-screen menu items and changes the values seen on the menu. Exits the menu. MEDIA.P: Displays Media Play. YAHOO!: Runs the Yahoo widget. 3D: Sets the 3D mode. FAV.CH: Displays Favorite Channel Lists on the screen. P.SIZE: Selects the picture size. CC: Controls the caption decoder. Displays and selects the available video sources. Press to directly access channels. Press to select additional channels (digital) being broadcasted by the same station. For example, to select channel “54-3”, press “54”, then press “–” and “3”. Adjusts the volume. Brings up the OSD. Displays the Content View, which includes Channel List, Internet@TV, Media Play, AllShare and 3D. Quickly select frequently used functions. Returns to the previous menu. These buttons are for the Channel List, Internet@TV, Media Play menu, etc. Use these buttons in Media Play and Anynet+ (HDMI-CEC) modes. (Q: Controls recording for Samsung recorders that have the Anynet+ feature)