MINOURA P-600AL Instruction Manual

Type-B: with Spring Washer 1 2 3 5 P-600AL "Closet Cyclist 2" instructions manual Upper Hook Main Pillar Lower Hook Reinforcement Bar Rear Leg Right Side Front Leg Height Adjuster Leg Base Plate Stainless Band Clip • For use of normal human-powered 2-wheel bicycles only. Heavy and long bikes such as tandem, electric assisted and downhill / freeride bikes don't fit P-600AL. • P-600AL may lose balance when hanging bike on just one side only depends on the bike weight. Be careful about the stability when taking off the bike. • You should setup P-600AL along a wall to prevent falling backward problem. Do not install the bike on the backside of P-600AL. Required Tools for Assembling Bolt Type Recognition Install both right and left Front Legs to the Leg Base Plate with the supplied M6x35 bolt (type-A), Flat washer, Collar and M6 Nylon nut. (see Fig. A) M6 Nylon Nut Collar M6 Flat Washer Left Side Front Leg Place the Rear Leg on the Leg Base Plate, and put the Pillar Base Plate onto the assembled legs. Put the M6x40 bolt (type-A) with M6 Flat Washer into the front side hole, then tighten to M6 Nylon Nut temporarily. (see Fig. B) Pillar Base Plate M6x40 Bolt (type-A) Rear Leg Put the M6x40 bolt (type-A) with M6 Flat washer into the backside hole and tighten to M6 Nylon Nut firmly. After that, tighten the front side bolt firmly too. (see Fig. C) M6x40 Bolt (type-A) Attach the Backside Leg on the back of the Main Pillar, then tighten with the supplied two M6x18 bolts (type-B) temporarily. Please note that you will tighten these bolts firmly after installing the Reinforcement Bars. (see Fig. E) Backside Leg M6x18 Bolt Main Pillar 1 x M5 Hex Wrench 1 x 10mm Spanner 1 x 13mm Spanner M6x35 Bolt (type-A) Leg Base Plate MADE IN JAPAN IMPORTANT NOTICES Be sure the Legs are different for right side and left side. Each Reinforcement Bar must be located inward. ! M6 Nylon Nut ! Be sure the collar insertion direction is different on right and left side. Follow as shown in Fig. A. (Fig. A) (Fig. B) (Fig. C) (Fig. D) (Fig. E) M6 Nylon Nut 4 Insert the Main Pillar onto the Pillar Base Plate. Make sure the Main Pillar must cover on the bracket, not placing beside the bracket. (see Fig. D) M6 Flat Washer M6 Flat Washer Stainless Band Clip (2009/07)

supplied M6x70 bolt (type-A), Plastic Shim, M6 flat washer and M6 Nylon nut. After installing the Reinforcement Bars, adjust the Backside Leg height to touch the floor all together, then tighten the M6x18 bolts on the Backside Leg firmly. (see Fig. F) Plastic Shim Reinforcement Bar Install Upper Hook (Fig. G) and Lower Hook (Fig. H) to the Main Pillar. Each bike requires both hooks and they are fully position adjustable. Find out the best position to hang down your bike most efficiently. To install the Stainless Band Clip, follow the steps below; 1) Once disassemble the Stainless Band Clip. 2) Open the band and wind it around the Main Pillar. 3) Lap the band ends (see Fig. I). The end with a welded nut must be inward. Make sure that both ends fit each other. If not, adjust the bending angle. 4) Attach the Plastic Bracket onto the band. It should be snapped in. Upper Hook Lower Hook P-600AL is a tall stand. You must maintain the balance whenever you use it to prevent from any accident. Adjust the Height Adjuster on each legs to keep the Main Pillar truly vertical and stable, then tighten the Lock Nut firmly with a 13mm spanner. (see Fig. K) < Complete Style with Bikes > For More Information MINOURA JAPAN MINOURA NORTH AMERICA (for ALL customers) (for U.S. residents ONLY) 1197-1 Godo, Anpachi 1996 East Avenue Gifu 503-2305 Japan Hayward, CA 94541-5454 U.S.A. Phone +81-584-27-3131 Phone 1-510-538-8599 Fax +81-584-27-7505 Fax 1-510-538-5899 Email [email protected] Email [email protected] Web www.minoura.jp Washer Washer Nylon Nut (Fig. F) If you have any questions or need help, you should contact the dealer where you purchased or the Minoura distributor in your country first. The distributor can be found on our web site. Only when you cannot get enough service, you can contact us. (Fig. K) Please attach the Lower Hook from the back of the rear wheel to support it, otherwise the bike will not become vertical to save the space due to the bike's weight balance. If the inside band end with welded nut has been angled against the bolt, you won't be able to screw the bolt in. Make sure the nut side end is properly set at right angle to the bolt. (see Fig. J) Do not push the bolt so much when screwing in. The band end will have to be bent and you are no longer tighten the bolt. 5) Put the bolt into the hole on the hook, then screw into the bracket gently. 6) Adjust the hook position and tighten the bolt firmly. Lock Nut Height Adjuster (Fig. G) (Fig. H) (Fig. I) (Fig. J) 90º Stainless Band (45mm) Plastic Bracket M6 Flat Washer M6x30 Bolt (type-A)