MINOURA PAIR STAND Manual 

(projection is foreside) Alloy Stay Frame Hook Bicycle display stand “PAIR STAND” instruction manual Please read this instuctions carefully before use. Thank you for purchasing Minoura PAIR STAND bike display stand. This stand can hold up to two bikes horizontally in a space as same as for only one bike. This stand is designed for standard two wheel bicycles. Do not use this stand for electric bikes or tandems. The weight limit for two bikes is 30 kgs. or 66 lbs. Make sure the stand is used on a level floor. Failing to set-up and use this stand on a level floor may cause the stand to fall over and cause damage or injury. This stand requires some assembly. You will need a M4 Hex wrench and a 13 mm spanner in order to assemble the PAIR STAND completely. IMPORTANT NOTES HOW TO ASSEMBLE YOUR PAIR STAND 1 Screw the foot adjuster to the nut located on each leg end. Insert four M8x55 bolts into the holes on the bottom of the Lower Pillar, then put through the legs. The long leg is for rear section, and the short legs are for front sec- tion. Be sure to fit the legs to the shape of the horrow of the bottom plate. Lower Pillar Rear Leg Bottom Plate Front Leg (Fig. A) (Fig. B) (Fig.C) Install the Reinforcement Arms between the Lower Pillar and the Front Legs by tightening the M6x14 bolts for the pillar side, and M6x30 bolts for the leg side. After installing the Reinforcement Arms, tighten the M8x55 bolts firmly. Wrong step may make you unable to install the Reinforcement Arms. Reinforcement Arm Reinforcement Arm Rear Leg Front Leg Upper Pillar Lower Pillar

lar. Connect the Upper Pillar to the Lower Pillar then tighten the M6x14 bolts firmly. Now the base frame is completed. Upper Pillar Connecting Plate Lower Pillar 5 (Fig. D) (Fig. E) 6 (Fig. H) FOR MORE INFORMATION For parts or service outside of Japan or North America, please con- sult your local shop or refer our international distributor list (found on our web site) for the distributor in your country. MINOURA JAPAN 1197-1 Godo, Anpachi, Gifu 503-2305 Japan Phone: +81-(0)584-27-3131 / Fax: +81-(0)584-27-7505 Email: [email protected] / Web: http://www.minoura.jp MINOURA NORTH AMERICA (for North American residents only) 1996 East Avenue, Hayward, CA 94541-5454 U.S.A. Fax: 1-510-538-5899 / Email: [email protected] MADE IN JAPAN Copyright 2002 Minoura Co.,Ltd. All rights reserved Assemble the cradles. Place the Angle Adjust Plate onto the Lower Support, then put the Alloy Stay on it. Fix three parts with the supplied M6x20 bolt in the upper hole. (see Fig. E) Screw the supplied M6x15 bolt in the lower hole, but you don’t need to tighten it so firmly at this time. Next, you'll install the bike cradles to both the upper and lower pillars. Disassemble the band clip first. (see Fig. H) Wrap the stainless band around the pillar, in-sert the end of the band between another end and the rectangle nut. Put the plastic bracket onto the band, attach the hook or support arm, then tighten the bolt. Stainless Band Plastic Bracket The distance between the plastic frame hooks can be adjusted to fit different sized bikes. To do so, loosen the rear nut and adjust the position of the hook. After adjusted to the required position firmly re-tighten the nut. (see Fig. F) 7 (Fig. F) The stainless band must ONLY be used on the upper side of the cradle. Do NOT use it on the bottom position of the cradle. (see Fig. G) (Fig. G) stainless band just putting onto the pole 8 The cradle is adjustable in degrees. If you want to move the cradle, loosend the lower bolt on the angle adjust plate, change the angle until the displayed bike will be horizontally as much as possible then tighten the bolt again. (see Fig. I) (Fig. I) To put a bike on PAIR STAND, lift the bike and gently place the top tube into the frame hooks. If the bike does not have a standard frame design, it should be supported by the top tube and rear seatstay configuration. (see Fig. J) 9 WHY MY NUT IS MISALIGNED? The inside nut of the stainless band clamp is not square, it is rectanle. You have to remove the stainless band to wind up it around the pole for assembling. At this time, do NOT remove the nut from the band. If you had removed the nut, make sure the nut direction that the longer side must be vertical. If you see there is some space between the nut and stainless band, the direction is wrong.